DOCSLIB.ORG

Stripped-Down Motor

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Stripped-Down Motor Stripped-Down Motor In this activity, you’ll make an electric motor—a simple version of the electric motors found in toys, tools, and appliances everywhere. What Do I Need? • aluminum foil • paper clips (larger is better) • paper, plastic, or foam cup • masking tape • magnets (two or more, available at Radio Shack) • scissors • copper wire (bare or coated) • sandpaper • battery (D or C cell) • permanent marker (any color is fine) What Do I Do? Building the Stand other piece of foil and paper clip. 1. Tear off two narrow sheets of aluminum foil. These will connect 4. Place the paper cup upside-down the motor to the battery. on the table. Tape the foil-covered 2. Take a paper clip and bend the outside wire down, so that you have a loop with post. Repeat with another paper clip. 3. Wrap one end of the aluminum foil around the long post of the paper clip. Make sure there is good contact between the paper clip and the foil. Repeat with the www.exploratorium.edu/afterschool Exploratorium end of one paper clip to the top of Turn over the cup and drop the inverted paper cup. Tape the another magnet inside. The two other paper clip to the opposite magnets will stick together. side. 6. Put the cup back on the table 5. Place a magnet on the top of the upside-down. This is the base for cup, between the paper clips. your motor. Making the Coil wire with two bare ends sticking 1. Cut a length of about 2 feet (60 out from either side. cm) of copper wire. 5. Balance the coil between two 2. If the wire is coated, use the fingers and see if it spins easily. If sandpaper to scrape away about it is too off-balanced to spin an inch (2 cm) of the coating on smoothly, adjust it. either end of the wire. 6. Use the permanent marker to 3. Wrap the coated part of the wire mark one side of one end of bare around the battery to make a coil, wire. then remove the coil from the battery. 7. Rest the ends of the coil in the cradles formed by the two paper clips. 8. Adjust the height of the paper clips so that when the coil spins, it just clears the top magnet. 9. Connect the battery by pressing the two free ends of the aluminum 4. Poke the bare ends of the wire foil pieces against either end of into and around the coil several the battery. times to fix the coil in place. You 10. Give the coil a spin to start the should now have a loop of coated motor turning. www.exploratorium.edu/afterschool Exploratorium Note: If the coil won’t spin, check that the coil is well balanced, that the coating has been thoroughly scraped off the ends, that the one end has been marked on one side with the marker, and that the coil and magnet are close but not touching. Keep adjusting if necessary—it will work. What’s Going On? Electricity flows through the coil of wire and creates an electromagnet. One face of the coil becomes a north pole, the other a south pole. The permanent magnet below attracts its opposite pole on the coil and repels its like pole, causing the coil to spin. Another way to explain this is the motor effect: when electricity moves through a wire in a magnetic field, a force results that moves the wire. Why is it important to color half of one projecting wire with a marker? By marking half of one end, you insulate the wire and prevent electricity from flowing through it for half of each spin. This turns off the electromagnet for that half spin, allowing momentum to carry it through to the next cycle. If you allowed the electricity to flow continually, one pole of the electromagnetic coil would just be continually attracted to the permanent magnet, and the coil wouldn’t spin. www.exploratorium.edu/afterschool Exploratorium.
Load more

Recommended publications
  • Electromagnetic Sheet Forming by Uniform Pressure Using Flat Spiral Coil
    materials Article Electromagnetic Sheet Forming by Uniform Pressure Using Flat Spiral Coil Xiaohui Cui 1,2,3,*, Dongyang Qiu 2, Lina Jiang 4, Hailiang Yu 1,2,3, Zhihao Du 1 and Ang Xiao 1 1 Light alloy research Institute, Central South University, Changsha 410083, China; [email protected] (H.Y.); [email protected] (Z.D.); [email protected] (A.X.) 2 College of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China; [email protected] 3 State Key Laboratory of High Performance Complex Manufacturing, Central South University, Changsha 410083, China 4 Shandong North Binhai Machinery Company, Zibo 255201, China; [email protected] * Correspondence: [email protected]; Tel.: +86-15388028791 Received: 13 May 2019; Accepted: 13 June 2019; Published: 18 June 2019 Abstract: The coil is the most important component in electromagnetic forming. Two important questions in electromagnetic forming are how to obtain the desired magnetic force distribution on the sheet and increase the service life of the coil. A uniform pressure coil is widely used in sheet embossing, bulging, and welding. However, the coil is easy to break, and the manufacturing process is complex. In this paper, a new uniform-pressure coil with a planar structure was designed. A three-dimensional (3D) finite element model was established to analyze the effect of the main process parameters on magnetic force distribution. By comparing the experimental results, it was found that the simulation results have a higher analysis precision. Based on the simulation results, the resistivity of the die, spacing between the left and right parts of the coil, relative position between coil and sheet, and sheet width significantly affect the distribution of magnetic force.
    [Show full text]
  • Overlapped Electromagnetic Coilgun for Low Speed Projectiles
    ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 Journal of Magnetics 20(3), 322-329 (2015) http://dx.doi.org/10.4283/JMAG.2015.20.3.322 Overlapped Electromagnetic Coilgun for Low Speed Projectiles Hany M. Mohamed1, Mahmoud A. Abdalla2*, Abdelazez Mitkees, and Waheed Sabery Electrical Engineering Branch, MTC College, Cairo, Egypt [email protected] [email protected] (Received 20 February 2015, Received in final form 16 June 2015, Accepted 16 June 2015) This paper presents a new overlapped coilgun configuration to launch medium weight projectiles. The proposed configuration consists of a two-stage coilgun with overlapped coil covers with spacing between them. The theoretical operation of a multi-stage coilgun is introduced, and a transient simulation was conducted for projectile motion through the launcher by using a commercial transient finite element software, ANSOFT MAXWELL. The excitation circuit design for each coilgun is reported, and the results indicate that the overlapped configuration increased the exit velocity relative to a non-overlapped configuration. Different configurations in terms of the optimum length and switching time were attempted for the proposed structure, and all of these cases exhibited an increase in the exit velocity. The exit velocity tends to increase by 27.2% relative to that of a non-overlapped coilgun of the same length. Keywords : electromagnetic launch, excitation circuit, lorentz force, overlapped coilgun 1. Introduction is not easy to obtain the main performance parameters and optimize the design [3]. Electromagnetic (EM) launch technology is a strong Sandia National Laboratories has succeeded in coilgun candidate to launch objects with high velocities over long design and operations by developing four guns with distances.
    [Show full text]
  • (12) United States Patent (10) Patent No.: US 9,000,647 B2 Rapoport (45) Date of Patent: Apr
    USOO9000647B2 (12) United States Patent (10) Patent No.: US 9,000,647 B2 Rapoport (45) Date of Patent: Apr. 7, 2015 (54) HIGH EFFICIENCY HIGH OUTPUT DENSITY (56) References Cited ELECTRIC MOTOR U.S. PATENT DOCUMENTS (76) Inventor: Uri Rapoport, Moshav Ben Shemen 5,396,140 A ck 3, 1995 Goldie et al. 310,268 (IL) 5,903,082 A 5/1999 Caamano 6,175,178 B1* 1/2001 Tupper et al. ................. 310,166 (*) Notice: Subject to any disclaimer, the term of this 6,259,233 B1 ck 658) ano f patent is extended or adjusted under 35 g: R g58. Shiki . 310,114 U.S.C. 154(b) by 318 days. 2004/0195931 A1* 10, 2004 Sakoda ......................... 310,268 2008/008.8200 A1* 4/2008 Ritchey......................... 310,268 (21) Appl. No.: 13/495,788 2012/0319518 A1* 12/2012 Rapoport ................. 310,156.12 (22) Filed: Jun. 13, 2012 k cited. by examiner O O Primary Examiner — John K. Kim (65) Prior Publication Data (74) Attorney, Agent, or Firm — The Law Office of Michael US 2012/O319518A1 Dec. 20, 2012 E. Kondoudis (57) ABSTRACT Related U.S. Application Data An electric motor that generates mechanical energy whilst increasing both the motor efficiency and the mechanical (60) Eyal application No. 61/497.536, filed on Jun. power density. The electric motor includes: a plurality of disk s Surfaces having a main longitudinal axis; a plurality of sta 51) Int. C tionary Support structures; and a rotating shaft affixed to the (51) Int. Cl. disk Surfaces. Each disk surface is coupled to an array of HO2K L/27 (2006.01) offset magnets.
    [Show full text]
  • Electromagnetic Launcher: Review of Various Structures
    Published by : International Journal of Engineering Research & Technology (IJERT) http://www.ijert.org ISSN: 2278-0181 Vol. 9 Issue 09, September-2020 Electromagnetic Launcher : Review of Various Structures Siddhi Santosh Reelkar Prof. Dr. U. V. Patil Department of Electrical Engineering, Department of Electrical Engineering, Government College of Engineering, Government College of Engineering, Karad Karad Prof. Dr. V. V. Khatavkar Department of Electrical Engineering, P.E.S. Modern college of Engineering, Pune Hrishikesh Mehta Utkarsh Alset Aethertec Innovative Solutions, Aethertec Innovative Solutions, Bavdhan, Pune Bavdhan, Pune Abstract— A theoretic review of electromagnetic coil-gun This paper is mainly focusing the basic principle of launcher and its types are illustrated in this paper. In recent electromagnetic coil-gun launcher, inductance and resistance years conventional launchers like steam launchers, chemical calculations, construction and modeling concept of different launchers are replaced by electromagnetic launchers with coil-gun launcher. auxiliary benefits. The electromagnetic launchers like rail- gun and coil-gun elevated with multi pole field structure delivers II. WORKING PRINCIPLE great muzzle velocity and huge repulse force in limited time. Rail gun has two parallel rails from which object is launched. Various types of coil-gun electromagnetic launchers are When current passes through the rails to the object it compared in this paper for its structures and characteristics. The paper focuses on the basic formulae for calculating the produces arc. Because of high current pulse it has more values of inductance and resistance of electromagnetic contact friction losses [4]. Compare to the rail-gun launcher, launchers. Coil-gun launchers have no contact friction losses as there is no electrical contact between coils and object.
    [Show full text]
  • Study on Characteristics of Electromagnetic Coil Used in MEMS Safety and Arming Device
    micromachines Article Study on Characteristics of Electromagnetic Coil Used in MEMS Safety and Arming Device Yi Sun 1,2,*, Wenzhong Lou 1,2, Hengzhen Feng 1,2 and Yuecen Zhao 1,2 1 National Key Laboratory of Electro-Mechanics Engineering and Control, School of Mechatronical Engineering, Beijing Institute of technology, Beijing 100081, China; [email protected] (W.L.); [email protected] (H.F.); [email protected] (Y.Z.) 2 Beijing Institute of Technology, Chongqing Innovation Center, Chongqing 401120, China * Correspondence: [email protected]; Tel.: +86-158-3378-5736 Received: 27 June 2020; Accepted: 27 July 2020; Published: 31 July 2020 Abstract: Traditional silicon-based micro-electro-mechanical system (MEMS) safety and arming devices, such as electro-thermal and electrostatically driven MEMS safety and arming devices, experience problems of high insecurity and require high voltage drive. For the current electromagnetic drive mode, the electromagnetic drive device is too large to be integrated. In order to address this problem, we present a new micro electromagnetically driven MEMS safety and arming device, in which the electromagnetic coil is small in size, with a large electromagnetic force. We firstly designed and calculated the geometric structure of the electromagnetic coil, and analyzed the model using COMSOL multiphysics field simulation software. The resulting error between the theoretical calculation and the simulation of the mechanical and electrical properties of the electromagnetic coil was less than 2% under the same size. We then carried out a parametric simulation of the electromagnetic coil, and combined it with the actual processing capacity to obtain the optimized structure of the electromagnetic coil.
    [Show full text]
  • Basics of Control Components
    Pilot Devices A pilot device directs the operation of another device (pushbuttons and selector switches) or indicates the status of the operating system (pilot lights). This section discusses Siemens 3SB and Furnas Class 51/52 pushbuttons, selector switches, and pilot lights. 3SB devices are available in 22 mm diameters. Class 51/52 pilot devices are available in 30 mm diameter. The diameter refers to the size of the knockout hole required to mount the devices. Class 51 devices are rated for hazardous locations environments such as Class I, Groups C and D and Class II, Groups E, F, and G. Class 52 devices are heavy duty for harsh, industrial environments. Bifurcated Contacts Whether one chooses the 3SB or the Class 51/52 pilot devices, the fine silver contacts have a 10 A/600 V continuous-current rating and can be used on solid state equipment. The 3SB and the Class 51/52 devices use bifurcated movable contacts. The design of the bifurcated contacts provides four different pathways for current to flow, thus improving contact reliability. 67 Pushbuttons A pushbutton is a control device used to manually open and close a set of contacts. Pushbuttons are available in a flush mount, extended mount, with a mushroom head, illuminated or nonilluminated. Pushbuttons come with either normally open, normally closed, or combination contact blocks. The Siemens 22 mm pushbuttons can handle up to a maximum of 6 circuits. The Furnas 30 mm pushbutton can handle up to a maximum fo 16 circuits. Normally Open Pushbuttons are used in control circuits to perform various Pushbuttons functions.
    [Show full text]
  • Electromagnetic Coil Gun – Design and Construction
    Bohumil SKALA Vladimir KINDL ELECTROMAGNETIC COIL GUN – DESIGN AND CONSTRUCTION ABSTRACT A single-stage, sensor less, coil gun was designed to demonstrate the capability to accelerate a ferromagnetic projectile to high velocity. This paper summarize all important steps during coil gun design, such as physical laws of the coil gun, preliminary calculations, the testing device and final product. The electromagnetic FEA model of the capacitor-driven inductance coil gun was constructed to be able to optimize the coil's dimensions. The driving circuit was implemented as dynamic model for simulation of current. The coil gun is designed for an exhibition centre as an exhibit. It is not designed for a really shooting applications, this means the projectile is accelerated at relatively low speed. Keywords: Coil gun, electronics, FEM, electromagnetic force 1. INTRODUCTION Electromagnetic accelerating systems are usually constructed as rail guns [3] or coil guns [1]. The rail gun is conceptually more simple than the coil gun, but has some inherent problems with plasma [2] during the projectile launches. That is why this conception is not use here. On the other hand the coil gun is much more suitable for common applications even if it needs some additional supporting facilities [4] such as energy accumulator, switcher and driver. Its main advantage lies in loose of almost all negative phenomena damaging the launch device. Doc. Ing. Bohumil SKALA, Ph.D. e-mail: [email protected] Ing. Vladimir KINDL, Ph.D. e-mail: [email protected] Dept. of Electromechanics and Power Electronics, University of West Bohemia in Pilsen, Univerzitní 8, 306 14 Pilsen, CZ PROCEEDINGS OF ELECTROTECHNICAL INSTITUTE, Issue 263, 2013 116 B.
    [Show full text]
  • Electromagnetic Coil Gun Launcher System
    ISSN(Online): 2319-8753 ISSN (Print) : 2347-6710 International Journal of Innovative Research in Science, Engineering and Technology (A High Impact Factor, Monthly, Peer Reviewed Journal) Visit: www.ijirset.com Vol. 8, Issue 3, March 2019 Electromagnetic Coil Gun Launcher System Prof. Yogesh Fatangde1 Swapnil Biradar2, Aniket Bahmne3, Suraj Yadav4, Ajay Yadav5 Department of Mechanical Engineering, RMD Sinhgad Technical Campus, Savitribai Phule Pune University, Pune, Maharashtra, India1 ABSTRACT: In our present time, a study was undertaken to determine if ground based electromagnetic acceleration system could provide a useful reduction in launching cost with current large chemical boosters, while increasing launch safety and reliability. An electromagnetic launcher (EML) system accelerates and launches a projectile by converting electric energy into kinetic energy. An EML system launches projectile by converting electric energy into kinetic energy. There are two types of EML system under development: rail gun and coil gun. A coil gun launches the projectile by magnetic force of electromagnetic coil. A higher velocity needs multiple stages of system, which make coil gun EML system longer. As a result installation cost is very high and it required large installation site for EML. So, we present coil gun EML system with new structure and arrangement for multiple electromagnetic coils to reduce the length of system KEYWORDS: EML, coil gun, Electromagnetic launcher, suck back effect I. INTRODUCTION In chemical launcher systems such as firearms and satellite launchers, chemical explosive energy is converted into mechanical dynamic energy. The system must be redesigned and remanufactured if the target velocity of the projectile is changed. In addition, such systems are not eco-friendly.
    [Show full text]
  • Electromagnetism Fall 2018 (Adapted from Student Guide for Electric Snap Circuits by Elenco Electronic Inc.)
    VANDERBILT STUDENT VOLUNTEERS FOR SCIENCE http://studentorgs.vanderbilt.edu/vsvs Electromagnetism Fall 2018 (Adapted from Student Guide for Electric Snap Circuits by Elenco Electronic Inc.) Here are some Fun Facts for the lesson Wind turbines generate electricity by using the wind to turn their blades. These drive magnets around inside coils of electric wire Electromagnets are used in junk yards to pick up cars and other heavy metal objects Electromagnetics are used in home circuit breakers, door bells, magnetic door locks, amplifiers, telephones, loudspeakers, PCs, medical imaging, tape recorders Magnetic levitation trains use very strong electromagnets to carry the train on a cushion of magnetic repulsion. Floating reduces friction and allows the train to run more efficiently. Materials 16 sets (of 2) D-batteries in holder 16 sets (of 2) nails wrapped with copper wire 1 nail has 50 coils and the other 10 coils 16 cases Iron fillings (white paper glued beneath for better visibility) 16 paper clips attached to each other 16 bags of 10 paper clips 16 circuit boards with: 4 # 2 snaps 1 # 1snap 1 # 3 snaps 1 electromagnet 1 switch 1 red and 1 black lead 1 voltmeter/ammeter 1 motor 1 magnet 1 red spinner (blade) 1 iron rod and grommet 16 simple motors 16 Transparent generators Observation sheet Divide class into 16 pairs. I. Introduction Learning Goals: Students understand the main ideas about magnets and electromagnets. A. What is a Magnet? Ask students to tell you what they know about magnets. Make sure the following information is included: All magnets have the same properties: All magnets have 2 magnetic poles.
    [Show full text]
  • Origin of the Electric Motor
    Origin of the Electric Motor JOSEPH C. MIGHALOWICZ MEMBER AIEE HE DAY that man Had it not been for the efforts of men like 1821—Michael Faraday dem- T molded the first wheel Davenport, De Jacobi, and Page, the benefits onstrated for the first time the from the sledlike skids of his of the electric motor would not be enjoyed possibility of motion by electro- magnetic means with the move- primitive wagon should be today. It is the purpose of this article to trace ment of a magnetic needle in a one of great commemoration, briefly the early history of the science of electro- field of force. had not its identity been lost motion and, in particular, to bring to light and 1829—-Joseph Henry, a teacher in the passing of time. Not to honor the inventor of the electric motor. of physics at the Albany Academy unlike the wheel and prob- in New York, constructed an elec- ably second only to the wheel, tromagnetic oscillating motor but considered it only a "philosophical the electric motor has been a toy." great benefactor to man and its history, too, slowly is 1833—Joseph Saxton, an American inventor, exhibited a magneto- being forgotten. Today, we hear very little, if anything, about Thomas Figure 1. Thomas Davenport, the blacksmith who invented the electric Davenport, inven- motor; or about De Jacobi, who propelled the first boat tor of the electric by means of an electric motor; or of Charles Page who motor successfully carried passengers on the first practical electric railway. Had it not been for the efforts of these men and others like them, the benefits of the electric motor probably would not be enjoyed today.
    [Show full text]
  • A 3D Printer for Interactive Electromagnetic Devices Huaishu Peng1,2 François Guimbretière1,2 James Mccann1 Scott E
    A 3D Printer for Interactive Electromagnetic Devices Huaishu Peng1,2 François Guimbretière1,2 James McCann1 Scott E. Hudson1,3 Disney Research Pittsburgh1 Computing and Information Science2 HCI Institute3 Pittsburgh, PA 15213 Cornell University Carnegie Mellon University [email protected] Ithaca, NY 14850 Pittsburgh, PA 15213 {hp356, fvg3}@cornell.edu [email protected] Figure 1. 3D printed electromagnetic devices. a) Solenoid used to actuate the cat hand; b) A Ferrofluid display; c) A movement sensor based on coupling strength; d) The stator and the rotor of a reluctance motor. The electromagnetic components are printed with a soft iron core, wound in place, and multiple layer of copper wire. ABSTRACT Author Keywords We introduce a new form of low-cost 3D printer to print 3D printing; computational crafts; electromagnets; rapid interactive electromechanical objects with wound in place prototyping; interactive devices; fabrication. coils. At the heart of this printer is a mechanism for ACM Classification Keywords depositing wire within a five degree of freedom (5DOF) H.5.m. Information Interfaces and Presentation (e.g. HCI): fused deposition modeling (FDM) 3D printer. Copper wire Miscellaneous can be used with this mechanism to form coils which induce magnetic fields as a current is passed through them. Soft iron INTRODUCTION wire can additionally be used to form components with high 3D printing technology has moved beyond simply magnetic permeability which are thus able to shape and instantiating 3D geometries to printing functional and direct these magnetic fields to where they are needed. When interactive objects. Recent work has considered how a range fabricated with structural plastic elements, this allows simple of functional objects might be fabricated, including 3D but complete custom electromagnetic devices to be 3D printed optical components [30], speakers [11], hydraulic printed.
    [Show full text]
  • A Review on Technological Advancement in Electromagnetic Coil Gun System
    Special Issue - 2018 International Journal of Engineering Research & Technology (IJERT) ISSN: 2278-0181 ICRTT - 2018 Conference Proceedings A Review on Technological Advancement in Electromagnetic Coil Gun System Sai Chaithanya, Vineeth Kumar P. K2 123 Shri Dharmasthala Manjunatheshwara Institute of Technology, Ujire, Karnataka, India 2 Department of Electrical & Electronics Engineering A ground based electrically powered launcher could significantly like a machine gun. It was powered by a large electrical motor reduce the complexity and cost of space launches for moderate and generator. It appeared in many contemporary science weight payloads. This paper presents results of a study to publications, but never piqued the interest of any armed estimate the required parameters. This study is based on forces. Similar principle is used in various areas such as linear electromagnetic gun technology which is constrained to a coaxial motors, Maglev Trains, Roller coasters, etc. Coil gun use geometry to take advantage of the efficiency of closely coupled coils. Each coil is sequentially fired as the projectile moves down electromagnetism to propel the projectile rather than using an the bore. A hybrid power electronic system has been used for explosive charge. firing of a projectile without any chemical substances, without Hence it can be called as fireless gun or a silent machine gun. any loud noise and without fire. There’s been speculation that, Coil gun requires high voltage, high amperage, and high this paper has involved in this research. With this in mind, this speed electrical switches. We can have a higher max paper humbly presents the crown jewel of the electronic projectile velocity.
    [Show full text]