DOCSLIB.ORG

Phenol Resorcinol Formaldehyde Resin Validation Date : 01/19/2015 Print Date : 07/08/2015 Manufacturer/Supplier/Impor : Hexion Canada, Inc

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Phenol Resorcinol Formaldehyde Resin Validation Date : 01/19/2015 Print Date : 07/08/2015 Manufacturer/Supplier/Impor : Hexion Canada, Inc Page:1/14 Material Safety Data Sheet FOR INDUSTRIAL USE ONLY Cascophen(TM) LT-5210Q 1. Product and company identification Product name : Cascophen(TM) LT-5210Q MSDS Number : 000000104568 Material uses : Wood Adhesives, Composites, Laminates or Related Board Products Product type : Phenol Resorcinol Formaldehyde Resin Validation date : 01/19/2015 Print date : 07/08/2015 Manufacturer/Supplier/Impor : Hexion Canada, Inc. ter 180 East Broad Street Columbus, Ohio 43215 USA Contact person : [email protected] Telephone : For additional health and safety or regulatory information, call 1 888 443 9466. Emergency telephone number : For Emergency Medical Assistance Call Health & Safety Information Services 1-866-303-6949 For Emergency Transportation Information CHEMTREC US Domestic (800) 424-9300 CHEMTREC International (703) 527-3887 CANUTEC CA Domestic (613) 996-6666 Part of the CASCO® Brand of Adhesives and Resins from Hexion Inc. 2. Hazards identification –Emergency overview Physical state : Liquid Color : Clear, reddish-brown Odor : Slight alcoholic Signal word : WARNING! Hazard statements : COMBUSTIBLE LIQUID AND VAPOR. MAY FORM EXPLOSIVE MIXTURES WITH AIR. INHALATION CAUSES HEADACHES, DIZZINESS, DROWSINESS AND NAUSEA AND MAY LEAD TO UNCONSCIOUSNESS. CAUSES EYE IRRITATION. MAY CAUSE RESPIRATORY TRACT AND SKIN IRRITATION. CONTAINS MATERIAL THAT CAN CAUSE TARGET ORGAN DAMAGE. CANCER HAZARD - CONTAINS MATERIAL WHICH CAN CAUSE Version: 9.1 Date of issue/Date of revision: 01/19/2015 Date of previous issue: 12/28/2011 Cascophen(TM) LT-5210Q Page:2/14 CANCER. Precautionary measures : Do not handle until all safety precautions have been read and understood. Obtain special instructions before use. Do not breathe vapor or mist. Use only with adequate ventilation. Do not eat, drink or smoke when using this product. Avoid contact with eyes, skin and clothing. Keep away from heat and flame. Keep container tightly closed. Use personal protective equipment as required. Wash thoroughly after handling. Potential acute health effects Inhalation : Can cause central nervous system (CNS) depression. Slightly irritating to the respiratory system. Ingestion : Can cause central nervous system (CNS) depression. Skin : Slightly irritating to the skin. Eyes : Severely irritating to eyes. Risk of serious damage to eyes. Potential chronic health effects Chronic effects : Contains material that can cause target organ damage. Signs and symptoms of chronic phenol poisoning may include vomiting, difficulty in swallowing, diarrhea, lack of appetite, jaundice, fatigue, bleeding or easy bruising and sometimes pain and swelling in the upper right abdomen, changes in urine output or dark urine, pain upon urination or in the lower back, or general edema. Can also cause cardiac damage evidenced by shortness of breath and in severe cases cardiac arrest. Preexisting medical conditions of the heart, kidney, liver, lung, eyes and skin may be aggravated by exposure. Carcinogenicity : Contains material which can cause cancer. Risk of cancer depends on duration and level of exposure. Mutagenicity : No known significant effects or critical hazards. Teratogenicity : No known significant effects or critical hazards. Developmental effects : No known significant effects or critical hazards. Fertility effects : No known significant effects or critical hazards. Target organs : Contains material which causes damage to the following organs: blood kidneys lungs the nervous system liver heart spleen gastrointestinal tract cardiovascular system upper respiratory tract immune system skin central nervous system (CNS) eye, lens or cornea pancreas thyroid Over-exposure signs/symptoms Inhalation : Adverse symptoms may include the following: nausea or vomiting Version: 9.1 Date of issue/Date of revision: 01/19/2015 Date of previous issue: 12/28/2011 Cascophen(TM) LT-5210Q Page:3/14 respiratory tract irritation coughing headache drowsiness/fatigue dizziness/vertigo unconsciousness Ingestion : No specific data. Skin : Adverse symptoms may include the following: irritation redness Eyes : Adverse symptoms may include the following: pain or irritation watering redness Medical conditions aggravated : Pre-existing disorders involving any target organs mentioned in this MSDS by over-exposure as being at risk may be aggravated by over-exposure to this product. See toxicological information (Section 11) 3. Composition/information on ingredients Name CAS number % by weight Resorcinol 108-46-3 >=5 - <10 Phenol 108-95-2 >=5 - <10 Sodium Hydroxide 1310-73-2 >=1 - <5 Ethanol 64-17-5 >=1 - <5 Methanol 67-56-1 >=0.1 - <1 Ethyl Acetate 141-78-6 >=0.1 - <1 There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section. 4. First aid measures Eye contact : Check for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical attention immediately. Skin contact : In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention immediately. Inhalation : Move exposed person to fresh air. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention immediately. Ingestion : Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention immediately. Protection of first aid : No action shall be taken involving any personal risk or without suitable personnel training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before Version: 9.1 Date of issue/Date of revision: 01/19/2015 Date of previous issue: 12/28/2011 Cascophen(TM) LT-5210Q Page:4/14 removing it, or wear gloves. Notes to physician : No specific treatment. Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. 5. Fire-fighting measures Flammability of the product : Combustible liquid. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. Extinguishing media Suitable : Use dry chemical, CO2, water spray (fog) or foam. Not suitable : Do not use water jet. Special exposure hazards : Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool. Hazardous thermal : Decomposition products may include the following materials: decomposition products carbon dioxide carbon monoxide metal oxide/oxides Special protective equipment : Fire-fighters should wear appropriate protective equipment and self- for fire-fighters contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. 6. Accidental release measures Personal precautions : No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Do not breathe vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment (see section 8 of SDS). Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Methods for cleaning up Small spill : Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor. Large spill : Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see section 13 of SDS). Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see section 1 of SDS for Version: 9.1 Date of issue/Date of revision: 01/19/2015 Date of previous issue: 12/28/2011 Cascophen(TM) LT-5210Q Page:5/14 emergency contact information and section
Load more

Recommended publications
  • Technical Data Sheet Polyproof Phenol Resorcinol Adhesive with Hardener
    a TECHNICAL DATA SHEET POLYPROOF PHENOL RESORCINOL ADHESIVE WITH HARDENER The combination Polyproof Adhesive with hardener is approved by NTI, Norway, Otto-Graf Institut (FMPA), Germany, SKH/KOMO (DHBC No. 32389), Holland for the production of load-bearing timber structures. Polyproof can be used in door production, lamination, finger jointing and other applications in the wood working industry, where there is demand for high water and weather resistance of the joints. The combination has short pressing times even at lower pressing temperatures. PRODUCT DESCRIPTION This super-professional, two part glue has been specially developed for waterproof exterior use and can stand continuous immersion in water. This glue is so waterproof - boat builders use it. Developed for the marine industry this is the only completely waterproof adhesive that will withstand continual immersion in water. For use externally where extreme weathering will take place. Arches for bridge work, concrete formers, marine craft construction, bonding of preservative treated timber.. Bonding of difficult timber i.e. teak and Iroko. Fire resistant to class 0. Used extensively for bonding difficult timbers such as teak and iroko where normal adhesives could fail.• structural timber • laminated roof members • timber in constant contact with water • timber in contact with the ground. DIRECTIONS FOR USE General Application for jointing To obtain the very best results the moisture content should be in the 12-14% range. Timber bought as kiln dried and stored under cover will present no problem. Perhaps as important as the glue is the preparation the joining surfaces, especially for Oak and oily timbers, Teak, Iroko etc.
    [Show full text]
  • APPENDIX G Acid Dissociation Constants
    harxxxxx_App-G.qxd 3/8/10 1:34 PM Page AP11 APPENDIX G Acid Dissociation Constants §␮ ϭ 0.1 M 0 ؍ (Ionic strength (␮ † ‡ † Name Structure* pKa Ka pKa ϫ Ϫ5 Acetic acid CH3CO2H 4.756 1.75 10 4.56 (ethanoic acid) N ϩ H3 ϫ Ϫ3 Alanine CHCH3 2.344 (CO2H) 4.53 10 2.33 ϫ Ϫ10 9.868 (NH3) 1.36 10 9.71 CO2H ϩ Ϫ5 Aminobenzene NH3 4.601 2.51 ϫ 10 4.64 (aniline) ϪO SNϩ Ϫ4 4-Aminobenzenesulfonic acid 3 H3 3.232 5.86 ϫ 10 3.01 (sulfanilic acid) ϩ NH3 ϫ Ϫ3 2-Aminobenzoic acid 2.08 (CO2H) 8.3 10 2.01 ϫ Ϫ5 (anthranilic acid) 4.96 (NH3) 1.10 10 4.78 CO2H ϩ 2-Aminoethanethiol HSCH2CH2NH3 —— 8.21 (SH) (2-mercaptoethylamine) —— 10.73 (NH3) ϩ ϫ Ϫ10 2-Aminoethanol HOCH2CH2NH3 9.498 3.18 10 9.52 (ethanolamine) O H ϫ Ϫ5 4.70 (NH3) (20°) 2.0 10 4.74 2-Aminophenol Ϫ 9.97 (OH) (20°) 1.05 ϫ 10 10 9.87 ϩ NH3 ϩ ϫ Ϫ10 Ammonia NH4 9.245 5.69 10 9.26 N ϩ H3 N ϩ H2 ϫ Ϫ2 1.823 (CO2H) 1.50 10 2.03 CHCH CH CH NHC ϫ Ϫ9 Arginine 2 2 2 8.991 (NH3) 1.02 10 9.00 NH —— (NH2) —— (12.1) CO2H 2 O Ϫ 2.24 5.8 ϫ 10 3 2.15 Ϫ Arsenic acid HO As OH 6.96 1.10 ϫ 10 7 6.65 Ϫ (hydrogen arsenate) (11.50) 3.2 ϫ 10 12 (11.18) OH ϫ Ϫ10 Arsenious acid As(OH)3 9.29 5.1 10 9.14 (hydrogen arsenite) N ϩ O H3 Asparagine CHCH2CNH2 —— —— 2.16 (CO2H) —— —— 8.73 (NH3) CO2H *Each acid is written in its protonated form.
    [Show full text]
  • Resorcinol and Sulfonates Criteria
    02/22/13 COMMONWEALTH OF PENNSYLVANIA DEPARTMENT OF ENVIRONMENTAL PROTECTION BUREAU OF POINT AND NON-POINT SOURCE MANAGEMENT RATIONALE FOR THE DEVELOPMENT OF AMBIENT WATER QUALITY CRITERIA RESORCINOL & SULFONIC ACID COMPOUNDS (Revised February 2012) (Revised February 2013) Introduction: Beazer East, Inc. (Beazer) implemented environmental investigations and remediation at sites in Butler and Armstrong Counties, Pennsylvania in cooperation with the Department of Environmental Protection (Department) and United States Environmental Protection Agency (U.S. EPA). These sites are located within an area approximately 60 square miles in size that has been designated by the Department under the Hazardous Sites Cleanup Act (HSCA) as the “Bear Creek Area Chemical Site” (BCACS). The Department has determined that environmental media (i.e. soil and groundwater) within the BCACS have been impacted by sulfonate (sulfonic acid) compounds and resorcinol and other hazardous substances. The sulfonic acid compounds include meta-benzene disulfonic acid (m-BDSA), benzene monosulfonic acid (BSA), p-phenol sulfonic acid (p-PSA). Currently, with respect to surface water, there are no ambient water quality criteria for the sulfonic acids or resorcinol, which are needed to evaluate the environmental clean-up objectives and progress within the BCACS. EPA and Department Review Aquatic Life Water Quality Criteria Developed by AMEC: Because water quality criteria had not been developed for the sulfonic acids or resorcinol by either the Department or the U.S. EPA, AMEC Earth & Environmental (AMEC) used U.S. EPA's national guidelines to develop aquatic life water quality criteria (Stephan, et al., 1985) in accordance with 25 Pa. Code § 16.22. (AMEC. April 2008).
    [Show full text]
  • Cure Rate of Resorcinol and Phenol-Resorcinol Adhesives in Joints of Ammonium Salt-Treated Southern Pine
    CURE RATE OF RESORCINOL AND PHENOL-RESORCINOL ADHESIVES IN JOINTS OF AMMONIUM SALT-TREATED SOUTHERN PINE U.S.D.A. FOREST SERVICE RESEARCH PAPER FPL 121 JANUARY 1970 U.S. Department of Agriculture/Forest Service/Forest Products Laboratory/Madison, Wis ABSTRACT A resorcinol resin adhesive of commercial manu­ facture, formulated for the purpose of gluing ammoni­ um salt-treated wood, gave excellent performance in joints of southern pine. Joints of the treated wood made with this adhesive passed the minimum require­ ments of a commercial standard for shear strength and wood failure. Six ordinary phenol-resorcinol or resorcinol resin adhesives did not meet the commer­ cial standard minimum requirements for gluing fire­ retardant-treated wood. Shear strength and wood failure were higher with all adhesives studied for untreated wood than for treated wood. The determina­ tion of the effect of an ammonium salt fire retardant on the increase in viscosity of these adhesives, in the absence of wood, predicted the better performance of the specially formulated adhesive with the treated wood. However, gluing studies were needed to deter­ mine the actual level of performance of the specially formulated adhesive. CURE RATE OF RESORCINOL AND PHENOL-RESORCINOL ADHESIVES IN JOINTS OF AMMONIUM SALT-TREATED SOUTHERN PINE FOREST PRODUCTS LABORATORY,1 BY FOREST SERVICE R.E. SCHAEFFER, CHEMIST U.S. DEPARTMENT OF AGRICULTURE INTRODUCTION The rate at which adhesives cure has always retardant-treated wood, on the curing rate of the been of importance to the wood industry. In a glueline. It has been shownthat typical ammonium large measure, this factor determines the gluing salt fire retardants increase the rate of gel of requirements for the particular operation for resorcinol resin adhesives while lowering the pH 3 which the adhesive is being considered.
    [Show full text]
  • Retreatment of Resorcinol-Formalin Past Root Fillings : Studies on Dissolving Properties of Various Solutions
    University of Connecticut OpenCommons@UConn SoDM Masters Theses School of Dental Medicine June 2006 Retreatment of Resorcinol-Formalin Past Root Fillings : Studies on Dissolving Properties of Various Solutions. Stanislav Aleksandrovich Moline Follow this and additional works at: https://opencommons.uconn.edu/sodm_masters Recommended Citation Moline, Stanislav Aleksandrovich, "Retreatment of Resorcinol-Formalin Past Root Fillings : Studies on Dissolving Properties of Various Solutions." (2006). SoDM Masters Theses. 1. https://opencommons.uconn.edu/sodm_masters/1 Retreatment of Resorcinol-Formalin Paste Root Fillings: Studies on Dissolving Properties of Various Solutions Stanislav Aleksandrovich Moline D.M.D., Tufts University, 2002 A Thesis Submitted in Partial Fulfillment of the Requirements for the Degree of Master of Dental Science At the University of Connecticut 2006 APPROVAL PAGE Master of Dental Science Thesis Retreatment of Resorcinol-Formalin Paste Root Fillings" Studies on Dissolving Properties of Various Solutions Presented by Stanislav Aleksandrovich Moline, D.M.D. Major Advisor Reza B. Kazemi D.M.D. Associate Advisor Kamran Safavi D.M.D., M.Ed. Associate Advisor Liisa Kuhn Ph.D. University of Connecticut 2006 DEDICATION To My Wife Tatyana Moline iii TABLE OF CONTENTS Page Title Page Approval Page ii Dedication iii Table of Contents iv Acknowledgement List of Tables vi List of Graphs viii List of SEM Images ix Introduction Purpose Null Hypothesis Materials and Methods Results 19 Discussion 45 Conclusion 53 References 55 iv Acknowledgement I would like to specially thank you Dr. Reza B. Kazemi for being not just an adviser, but also a true mentor. He was very supportive and patience in guiding me through this project.
    [Show full text]
  • Waste Water Treatment of Resorcinol Production
    1933 A publication of CHEMICAL ENGINEERINGTRANSACTIONS VOL. 61, 2017 The Italian Association of Chemical Engineering Online at www.aidic.it/cet Guest Editors:Petar SVarbanov, Rongxin Su, Hon Loong Lam, Xia Liu, Jiří JKlemeš Copyright © 2017, AIDIC ServiziS.r.l. ISBN978-88-95608-51-8; ISSN 2283-9216 DOI: 10.3303/CET1761320 Waste Water Treatment of Resorcinol Production Huanong Cheng*, Guangchao Gao, Shiqing Zheng Center of Computer and Chemical Engineering，Qingdao University of Science and Technology，Qingdao 266042， Shandong China [email protected] Wastewater of resorcinol production that included acid, m-phenylenediamine, m-aminophenol, resorcinol, and other impurities was generated by m-phenylenediamine hydrolysis. In this paper formaldehyde condensed with organics of wastewater to form oligomeric solid polymer that could be separated by filtration. The oligomeric solid polymer could be used as plasticizer of rubbers. And then the acidity of wastewater was neutralized by adding ammonia water. It was found that other impurity reacted with ammonia and precipitated from the solution in the neutralized process. Methanol and n-butyl ester of wastewater were removed by stripping one third water after forward two steps. Lastly activated carbon was utilized to adsorb trace organics and impurities, and then water was evaporated to product ammonium sulphate. An orthogonal experiment about adsorption temperature, activated carbon quantity, stirring time was arranged to gain optimal activated carbon adsorption operation conditions. The condensed mole ratio of formaldehyde and organics, neutralized pH value, and the activated carbon adsorption conditions were investigated to achieve the minimum impurities, the qualified nitrogen content, and the best color of ammonium sulphate.
    [Show full text]
  • Dissociation Constants of Organic Acids and Bases
    DISSOCIATION CONSTANTS OF ORGANIC ACIDS AND BASES This table lists the dissociation (ionization) constants of over pKa + pKb = pKwater = 14.00 (at 25°C) 1070 organic acids, bases, and amphoteric compounds. All data apply to dilute aqueous solutions and are presented as values of Compounds are listed by molecular formula in Hill order. pKa, which is defined as the negative of the logarithm of the equi- librium constant K for the reaction a References HA H+ + A- 1. Perrin, D. D., Dissociation Constants of Organic Bases in Aqueous i.e., Solution, Butterworths, London, 1965; Supplement, 1972. 2. Serjeant, E. P., and Dempsey, B., Ionization Constants of Organic Acids + - Ka = [H ][A ]/[HA] in Aqueous Solution, Pergamon, Oxford, 1979. 3. Albert, A., “Ionization Constants of Heterocyclic Substances”, in where [H+], etc. represent the concentrations of the respective Katritzky, A. R., Ed., Physical Methods in Heterocyclic Chemistry, - species in mol/L. It follows that pKa = pH + log[HA] – log[A ], so Academic Press, New York, 1963. 4. Sober, H.A., Ed., CRC Handbook of Biochemistry, CRC Press, Boca that a solution with 50% dissociation has pH equal to the pKa of the acid. Raton, FL, 1968. 5. Perrin, D. D., Dempsey, B., and Serjeant, E. P., pK Prediction for Data for bases are presented as pK values for the conjugate acid, a a Organic Acids and Bases, Chapman and Hall, London, 1981. i.e., for the reaction 6. Albert, A., and Serjeant, E. P., The Determination of Ionization + + Constants, Third Edition, Chapman and Hall, London, 1984. BH H + B 7. Budavari, S., Ed., The Merck Index, Twelth Edition, Merck & Co., Whitehouse Station, NJ, 1996.
    [Show full text]
  • Safety Data Sheet
    SAFETY DATA SHEET Preparation Date: 06/10/2015 Revision Date: 06/28/2018 Revision Number: G2 1. IDENTIFICATION Product identifier Product code: R1004 Product Name: RESORCINOL, REAGENT Other means of identification Synonyms: 1,3-Benzenediol 1,3-Dihydroxybenzene 3-Hydroxycyclohexadien-1-one 3-Hydroxyphenol Benzene, 1,3-dihydroxy- Benzene, m-dihydroxy- C.I. 76505 C.I. Developer 4 C.I. Oxidation Base 31 Developer O Developer R Developer RS Dihydroxybenzol Durafur developer G Fouramine RS Fourrine 79 Fourrine EW Nako TGG Pelagol Grey RS Pelagol RS Phenol, m-hydroxy- Resorcin Resorcine Resorcinol Resorcinolum Resorzin m-Benzenediol m-Dihydroxybenzene m-Dioxybenzene m-Hydroquinone m-Hydroxyphenol CAS #: 108-46-3 RTECS # VG9625000 CI#: Not available Recommended use of the chemical and restrictions on use Recommended use: In tanning; manufacturing resins, resin adhesives, hexylresoricnol, p-amino salicyclic acid, explosives, and dyes; In rubber industry for tires and reinforced rubber products; wood adhesives; pharmaceuticals; cross-linking agent; a rubber tackifier; and cosmetic; In photography; chemical intermediate used in oxidation hair dyes; medication. Product code: R1004 Product name: RESORCINOL, 1 / 13 REAGENT Uses advised against No information available Supplier: Spectrum Chemical Mfg. Corp 14422 South San Pedro St. Gardena, CA 90248 (310) 516-8000 Order Online At: https://www.spectrumchemical.com Emergency telephone number Chemtrec 1-800-424-9300 Contact Person: Martin LaBenz (West Coast) Contact Person: Ibad Tirmiz (East Coast) 2.
    [Show full text]
  • 604 Quantitative Estimation of Sialic Acids Ii. A
    604 BIOCHIMICA ET BIOPHYSIC.k .\CT.k VOL. 24 (i957) QUANTITATIVE ESTIMATION OF SIALIC ACIDS II. A COLORIMETRIC RESORCINOL-HYDROCHLORIC ACID METHOD', *" LARS SVENNERHOLM Department of Medical Biochemistry, University o[ Gothenburg, Gothenburg (Sweden) In a previous communication 1 the quantitative estimation of sialic acids with orcinol- hydrochloric acid (Bial's reagent) has been described. With this method the keto- hexoses, when tested in dilute solutions, gave a colour that was impossible to dis- tinguish from that of the sialic acids. Thus Bial's reagent cannot be used for the estimation of sialic acids when they occur together with ketohexoses. The amount of ketohexoses is low in animal materials and will not seriously disturb the determination of sialic acids. SPRINGER it, however, has reported that sialic acids also occur in plant materials, where the content of ketosugars is much greater. Therefore, a systematical investigation was performed to find out whether it would be possible to determine sialic acids when they occur in the same samples as ketohexoses. Reagents used for the estimation of ketohexoses were tested in order to obtain a reagent that gave different colours with ketohexoses and sialic acids. The results of the testing are collected in Table I. In the resorcinol method of COLE et al. ~ sialic acids and fructose gave quite different colours. From the other tests some general trends in the colour formation of sialic acids could be observed. The colour formation was strongly promoted by Cu ~+ or Fe ~+, while alcohols or acetic acid inhibited it to a great extent. On the basis of these general principles a method was worked out.
    [Show full text]
  • Environmental Indicator Groundwater Indspec Chemical Corporation
    DOCUMENTATION OF ENVIRONMENTAL INDICATOR DETERMINATION Interim Final 2/5/99 RCRA Corrective Action Environmental Indicator (EI) RCRIS code (CA750) Migration of Contaminated Groundwater Under Control Facility Name: Beazer/INDSPEC Properties Facility Address: 133 Main Street, Petrolia, Pennsylvania Facility EPA ID #: PAD004336731 1. Has all available relevant/significant information on known and reasonably suspected releases to the groundwater media, subject to RCRA Corrective Action (e.g., from Solid Waste Management Units (SWMU), Regulated Units (RU), and Areas of Concern (AOC)), been considered in this EI determination? X If yes - check here and continue with #2 below. If no - re-evaluate existing data, or if data are not available skip to #6 and enter“IN” (more information needed) status code. BACKGROUND Definition of Environmental Indicators (for the RCRA Corrective Action) Environmental Indicators (EI) are measures being used by the RCRA Corrective Action program to go beyond programmatic activity measures (e.g., reports received and approved, etc.) to track changes in the quality of the environment. The two EI developed to-date indicate the quality of the environment in relation to current human exposures to contamination and the migration of contaminated groundwater. An EI for non-human (ecological) receptors is intended to be developed in the future. Definition of “Migration of Contaminated Groundwater Under Control” EI A positive “Migration of Contaminated Groundwater Under Control” EI determination (“YE” status code) indicates that the migration of “contaminated” groundwater has stabilized, and that monitoring will be conducted to confirm that contaminated groundwater remains within the original “area of contaminated groundwater” (for all groundwater “contamination” subject to RCRA corrective action at or from the identified facility (i.e., site-wide)).
    [Show full text]
  • Resorcinol Resin
    Resorcinol Resin RS-12A/RXS-22A WOODWORKING ADHESIVE SYSTEM RESIN RS-12A is a resorcinol phenol formaldehyde resin adhesive used with HARDENER RXS- 22A. This system is widely used for timber laminating, door, window and panel making, and general joinery when a high degree of durability is required. It has particularly good water resistance and satisfies the requirements of BS EN 301, Adhesive Type l and BS1203 WBP. It is also capable of bonding components to achieve Class 0 fire resistance. It may be used in conventional hot and cold presses and in the general gluing processes normally encountered in the woodworking industry. TYPICAL PROPERTIES RESIN RS-12A Appearance Thin reddish brown liquid Solids contents (3 h @ 120°C) 56% Viscosity @ 25°C 3.5 P Specific gravity @ 25°C 1.12 pH 8.5 Diluent for washing Water Storage life @ 20°C 1 year HARDENER RXS-22A Appearance Beige powder Storage life @ 20°C 1 year QUALITY To ensure consistent bond quality, the product is manufactured to within a strict product specification. However, it is also important for the user to make regular quality checks. Should any changes be made to the materials to be bonded, the equipment or the process, particular care should be taken to check the bond quality. Whilst offering technical help and advice, Wessex Resins and Adhesives Ltd cannot accept responsibility for actions beyond our control. HEALTH AND SAFETY Please read the relevant Material Safety Data Sheet CAREFULLY. HARDENERS Resorcinol phenol formaldehyde resins are cured by the addition of a hardener. RESIN RS-12A is a fairly low viscosity resin and is easily mixed with powder hardener RXS- 22A.
    [Show full text]
  • Resorcinol-Formaldehyde Resin “Russian Red” Endodontic Therapy
    JOURNAL OF ENDODONTICS Printed in U.S.A. Copyright © 2003 by The American Association of Endodontists VOL. 29, NO.7,JULY 2003 Resorcinol-Formaldehyde Resin “Russian Red” Endodontic Therapy Nathan W. Schwandt, DDS, and Tom G. Gound, DDS, MS Resorcinol-formaldehyde resin is a material used discuss clinical considerations when evaluating and retreating RF in endodontic therapy in many foreign countries. cases. With immigration to the United States increasing, American dentists need to become familiar with resorcinol-formaldehyde therapy. It contains two Components of Resorcinol-Formaldehyde Resin potentially toxic components, formaldehyde (liq- Formaldehyde pastes have been used for endodontic therapy for uid) and resorcinol (powder). Zinc oxide or barium over a century. In 1898, Gysi introduced a formaldehyde paste sulfate may be used for radiopacity. When 10% known as Gysi’s Triopaste for endodontic therapy (3). Its purpose sodium hydroxide is added to the mixture, poly- in paste formulations is to cause histopathologic fixation of the merization occurs, which can form a brick-hard red remaining pulp tissue. Fixation refers to the process of cross- material that has no known solvent. Several varia- linking proteins that purportedly inhibits autolysis of the pulp tions in technique exist. The catalyst can be mixed tissue. Formaldehyde is also an effective antimicrobial agent in before insertion into the tooth, added after the against bacteria, fungi, and virus. However, its efficacy is depen- mixture is inserted, or not used. Providers believe dent on conditions within the pulp chamber and canal and may be pulp tissue will be fixed and bacteria destroyed limited because of its tendency to bind to organic matter.
    [Show full text]