r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 1 Owner’s ManualManual Instruction Book for: ™ Model 552552 Autoloading RimfireRimfire RifleRifle && ™ Model 572572 Pump ActionAction RimfireRimfire RifleRifle

IMPORTANT! This manual contains operating, care, and maintenance instructions. To ensure safe operation, any user of this firearm must read and understand this manual before using the firearm. Failure to follow the instructions and heed the warnings in this manu- al can cause property damage, personal injury, and/or death. This manual should always accompany this firearm, and be transferred with it upon change of ownership. WARNING! Keep this firearm out of the reach of children, unauthorized individuals, and others unfamiliar with safe handing of firearms.

page 2...... the ten commandments of firearm safety

page 7...... important parts of the firearm

page 10...... how to load and unload

page 13 ...... lubrication and maintenance

page 20 ...... how to obtain parts and service

Model 572™ Shown r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 2

A Tradition of Performance and Safety. • L In 1816 Eliphalet Remington was confident he could make a flintlock that was as good or cou better than any he could buy. His confidence was well founded. The barrel he handcrafted clim set a new standard for firearm accuracy and spawned generations of products that have you hol made Remington® Arms America’s leading gunmaker. While performance and style are certainly hallmarks of Remingtonfirearms, one factor ultimately drives their performance. • C Safety. Eliphalet Remington never lost sight of the fact that his rifles were potentially lethal inte and could kill someone if handled improperly. And after more than 180 years the same ers holds true for any firearm, including your new Remington. Eliphalet Remington’s first flint- Eliphalet Remington’s first Eve flintlock launched a proud tradition or lock launched a proud tradition of accuracy and responsibility. of accuracy & responsibility. sec Safety is Critical to Performance. • S A superbly crafted gun is only as good as the hands that hold it. You can never be too careful. Shooting fire accidents are often caused by careless oversights such as failing to control the direction of the muzzle, failing to • T fully engage the safety, leaving ammunition in the chamber or using improper loads. These oversights can result can in the destruction of life, limb or property. There’s no calling back a bullet once it’s been fired, so it’s oth critical that you know the principles of safe gun handling and storage before you ever take your new Remington • A firearm out of the box. fire The proper use and performance of your firearm depends on correct assembly and maintenance, so it’s critical sur that you familiarize yourself with the information in this instruction book. Even if you’re a veteran shooter with a collection of Remington firearms, take the time to read this literature. Not all firearms are the same. That means the first step in safe handling is to learn the features and requirements of your new Remington.

T h e T e n CommandmenTs o f f i r e a r m s a f e T y The Ten Commandments of Firearm Safety should be etched in your memory forever. Let them govern your Trea action wherever and whenever you’re involved with firearms. In the field. On the range. Or in your home. care Please take the time to review and understand these rules. dev Hum 1st C o m m a n d m e n t real unlo Always Keep the Muzzle Pointed in a Safe Direction. It's This is the most important firearm safety rule. A safe direction is one in which an acci- Nev dental discharge will not cause injury to yourself or others. Never allow your firearm to you point at anything you don't intend to shoot. Be especially careful when you're loading or fire unloading. Treat every firearm as if it were loaded. And make it a habit to know where the muzzle is pointed at all times, even when your firearm is un-loaded. No one will be injured Bef by an accidental discharge if you keep your firearm pointed in a safe direction. It's as sim- firea ple as that. mu are fire 2nd C o m m a n d m e n t Firearms should be Unloaded When Not Actually in Use. Load your firearm only when you're in the field or on the target range and ready to fire. Never let a loaded firearm out of your sight or out of your hands. Unload it as soon as you're finished shooting - before you bring it into your car, camp or home. Remember, unloading your firearm means unloading it completely, so there is no ammunition in the chamber or in the magazine. Before handling a firearm or passing it to someone else, visually check the chamber, receiver and magazine to be certain they do not contain ammunition. Always keep the firearm's action open when not in use. Never assume a firearm is unloaded even if you were the last person to use it. Always check for yourself.

2 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 3

• Let common sense rule when you carry a loaded firearm. If you're in a situation that could risk accidental discharge - such as crossing a fence, wading through a stream or climbing a tree - always unload your firearm. Never pull or push a loaded firearm toward yourself or another person. And never carry a loaded firearm in a scabbard, detached holster or gun case.

• Certain firearms (including some Remington® rifles and shotguns) are equipped with internal security devices to prevent unauthorized use. In addition, some firearms own- ers use external devices, such as cable locks and trigger blocks, for the same purpose. Firearms should be stored in a secure place where children n’s first Even if you use such a device, you should still keep your firearm unloaded when stored cannot access them. A gun safe ud tradition or not in use. And using internal or external devices cannot substitute, however, for is an ideal way to secure your nsibility. securing your firearms and ammunition in a separate, locked location. firearm • Safe storage of firearms is just as critical as safe handling. Never store firearms loaded. Be sure to keep your oting firearms in a secure place where unauthorized persons cannot get their hands on them without your knowledge. ng to • Take special care if there are children around. Children are fascinated by firearms. It's a natural curiosity that esult can have tragic consequences when not properly supervised. Store your firearms in a locked firearm safe or some it’s other location that physically bars a child from gaining access. gton • Ammunition should be stored and locked in a location separate from your firearm. Never leave an unsecured firearm or ammunition in a closet, dresser drawer or under the bed. Remember, it is your responsibility to make tical sure that children and others unfamiliar with firearms cannot get access to your firearm and ammunition. ith a eans

3rd C o m m a n d m e n t DON'T RELY ON YOUR GUN'S SAFETY

our Treat every firearm as if it can fire at any time, whether or not there's pressure on the trigger. Your firearm has been carefully designed to maximize performance and safety. However, because a firearm's safety is a mechanical device, it could fail. Human error is a more likely reason for a firearm safety to fail. By mistake, you may think the safety is on when it really isn't. Or the safety may have been disengaged without your knowledge. Or you could think your firearm is unloaded when there's actually a cartridge or shell in it. A mechanical safety is not a substitute for common sense. It's merely a supplement to your proper handling of a firearm. Never touch the trigger on a firearm until you are ready to shoot. Keep your fingers away from the trigger when you're loading or unloading. And don't pull the trigger when the safety is engaged or positioned between safe and fire.

Before using your firearm, read this instruction book to understand the exact location and operation of your firearm's safety. Even when the safety is on, maintain control of your loaded firearm and control the direction of the muzzle. In other words, don't rely on your safety to justify careless handling. If your firearm's internal mechanisms are broken or have been altered, your firearm may fire even when the safety is on. Remember, you and your safe firearm handling practices are your firearm's best safety. 4th C o m m a n d m e n t BE SURE OF YOUR TARGET AND WHAT’S BEYOND IT. rearm o your You can't stop a shot in mid-air, so never fire unless you know nition exactly where your shot is going and what it will strike. Never ck the fire at a sound, a movement or a patch of color. Before you pull action the trigger be absolutely sure of your target and what's behind it. check Make sure the shot has a backstop such as a hillside or dense material like sand. Remember, bullets can travel great distances with tremendous velocity. Know how far your shot will go if you miss your target or the bullet ricochets.

3 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 4

5th C o m m a n d m e n t Use Proper Ammunition Every firearm is designed to use a certain caliber or gauge of ammunition. Using the wrong ammunition, mixing ammu- nition or using improperly reloaded ammunition can cause serious personal injury or death. And it only takes one car- If for tridge or shotshell of the incorrect caliber or gauge, or which has been improperly reloaded, to destroy your firearm. It's Comm your responsibility to make sure the ammunition you use exactly matches the caliber or gauge of your firearm. Refer to the br this instruction book to find out the specific requirements of your firearm. Always read and heed the instructions on ly. R ammunition boxes. tried Confusing shells or cartridges can cause serious personal injury or death and destroy your firearm. Examine your shells or cartridges closely and use only the precise caliber or gauge for your specific firearm. For example, suppose you acci- dentally loaded a 20 ga. shell into a 12 ga. shotgun. Because the 20 ga. shell is too small for the chamber, the 20 ga. shell could travel down the barrel and get lodged in the bore. If you then loaded a standard 12 ga. shell behind it and Your fired, the 12 ga. shot will slam into the lodged 20 ga. shell and may cause the barrel to explode right in your hand. This times is commonly called a 12/20 burst, and it can kill you. chips Check all ammunition before you load it to make sure it matches your firearm's requirements. Every Remington® car- the fi tridge and shell is head-stamped with its caliber or gauge for easy identification. Likewise, you'll find the caliber or gauge ing a of your new Remington firearm imprinted on the barrel. come reloading requires extra diligence. nently If you're an ammunition reloader, you are responsible for personally assuring that the loads and components of your prote reloaded ammunition meet your firearm's factory-tested standards. Never use ammunition, which has been reloaded by someone else! Many shooters handload as a hobby or to save money on commercial, factory-made ammunition. However, it requires a thorough knowledge of reloading procedures and a deep respect for the explosive potential of gunpowder. Befor Firearms are designed, manufactured and proof-tested to standards based on factory-loaded ammunition. Handloaded zine. or reloaded ammunition that deviates, either intentionally or accidentally, from load or component recommendations can greas be very dangerous. clean Reloaders must observe all possible safety precautions and practices related to the proper handling of explosives. Never Whether you're a seasoned reloader or just starting out, you should study the subject, watch reloading demonstrations When and talk to experienced reloaders. your The first rule of reloading is to always follow the manufacturer's instructions for the components you're using. They'll when tell you to follow certain guidelines. Namely: free o 1. Don't mix or substitute powders or primers. 2. Don't use unknown or substandard components. 3. Use only suitable components that have been factory-tested by reputable ammunition, powder and bullet manufacturers. 4. Always be sure to use the manufacturer's recommended recipe when reloading. Your Not following these guidelines could result in severe injury to yourself or severe damage to your firearm. Dangerously high safety pressure and explosions can result from an overcharge of powder or other deviations from established reloading guidelines. So ne Be very careful. The process of reloading exposes you to environmentally hazardous material. Lead, which is known to cause cancer and birth defects, is the most common substance in bullets and shot. It is important to handle lead bullets and shot with extreme care. Work only in a well-ventilated area and always wash your hands after exposure and before eating. Never smoke while reloading. Primers and powders are also highly toxic and flammable. So after reloading be sure to clean up all materials from your work area. Don't leave primer or powder spills anywhere on the floor or bench top. Dispose of all waste material in accor- dance with the manufacturer's recommendations.

Finally, when reloading or handloading concentrate on what you're doing at all times. Do not be distracted by talking to others, listening to the radio or watching TV while reloading. Never reload after consuming alcoholic beverages or drugs of any kind. You are working with extremely hazardous materials and you can't risk even a few seconds of distraction. the b Remember, if you reload, you are the ammunition manufacturer and you are responsible for the performance and safe- Make ty of your reloaded ammunition. and a expos

4 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 5

6th C o m m a n d m e n t mmu- IF YOUR FIREARM FAILS TO FIRE WHEN THE TRIGGER IS PULLED, HANDLE WITH CARE. ne car- If for some reason the ammunition doesn't fire when you pull the trigger, stop and remember the 1st m. It's Commandment of Firearm Safety - always keep the muzzle pointed in a safe direction. Keep your face away from efer to the breech, then put the safety on, carefully open the action, unload the firearm and dispose of the cartridge safe- ons on ly. Remember that anytime there's a shell in the chamber, your firearm is loaded and ready to use. Even if you tried to shoot and your firearm didn't fire, treat your firearm as if it could still discharge. shells u acci- 7th C o m m a n d m e n t 20 ga. ALWAYS WEAR EYE AND EAR PROTECTION WHEN SHOOTING. it and Your sight and hearing risk injury from shooting and should be protected at all d. This times. Wear protective shooting glasses to guard against falling shot, clay target

chips, powder residue, ruptured cartridge cases and even twigs and branches in n® car- the field. Also be sure to wear eye protection when you're disassembling or clean- gauge ing a firearm so that tensioned parts (like springs) and cleaning solvents don't come in contact with your eyes. Continued exposure to shooting noise can perma- nently damage your hearing. On the range, where shooting volume is the loudest, be sure to use the maximum f your protection of a headset. Learn to use ear protection at all times. ded by

8th C o m m a n d m e n t quires E URE THE ARREL IS LEAR OF BSTRUCTIONS EFORE HOOTING B S B C O B S . Before loading your firearm, open the action and make sure there's no ammunition in the chamber or maga- oaded zine. Check the barrel for any obstructions or debris. Even a small amount of snow, mud, excess lubricant or ns can grease in the bore can dangerously increase pressure and cause the barrel to bulge or burst when firing. Use a cleaning rod and patch to wipe away anti-rust compounds or any other residues or obstructions in the barrel. osives. Never try to shoot out an obstruction by loading another shell and firing! ations When firing, rely on your instincts. If the noise or recoil of your firearm seems weak, stop everything, unload your firearm and be sure nothing is lodged in the barrel. Remember the 12/20 burst? That's what can happen They'll when the barrel is obstructed. Always be sure you're using the correct ammunition in your firearm and that it's free of obstructions.

9th C o m m a n d m e n t DON'T ALTER OR MODIFY YOUR FIREARM. HAVE IT SERVICED REGULARLY. Your firearm has been designed to operate according to certain factory specifications. You'll jeopardize your y high safety and that of others around you by attempting to alter its trigger, mechanical safety or other mechanisms. elines. So never alter or modify your firearm in any way. cause Like any mechanical device, a firearm is subject to wear. It must be main- d shot tained and periodically serviced to assure optimum safety and performance. Never Only a qualified service facility should service, repair or modify your Remington® firearm. Consult your instruction book for instructions on how m your to send your firearm to the factory or for the location of the nearest accor- Remington Authorized repair station.

Proper cleaning and lubrication are also important to firearm maintenance king to and are necessary to assure accuracy, safety and reliability. Before cleaning, drugs always make sure that your firearm is completely unloaded. And always clean action. the barrel from the chamber end to the muzzle when possible. d safe- Make it a practice to clean your bore every time you're going to shoot. Be sure to clean your entire firearm before

and after long-term storage and no less than once a year. It's also important to clean your firearm whenever it's been exposed to adverse conditions such as rain, dirt, mud, snow, sleet or saltwater.

5 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 6

For safe and dependable operation of your firearm, all parts of your firearm must be properly cleaned and lubri- Rem cated. Periodically inspect the internal workings of your firearm to be sure they're clean and free of rust, unwant- Aut ed dirt and debris. Cong Use recommended lubricants on your firearm and do not over-lubricate. The use of a non-recommended lubricant use a could adversely affect the function and safe operation of your firearm. Remember, you are responsible for the proper in fac care and maintenance of your firearm. Failure to properly maintain your firearm cannot only damage or ruin your firearm, it can expose you and others to unnecessary risks of personal injury or death. PICTU Remington® has a wide range of firearm care products and resources for best results when cleaning your firearm. MODEL 572™ Everything from solvents and lubricants to rods and patches. They're all available from your Remington dealer. St

10th C o m m a n d m e n t LEARN THE MECHANICS AND HANDLING CHARACTERISTICS OF YOUR FIREARM. Not all firearms are alike. They have different mechanical characteristics that dictate how you should carry and handle them. Anyone who plans to use a firearm should first become totally familiar with the type of firearm it is and the safe handling procedures for loading, unloading, carrying, shooting and PICTURE 1 B ™ storing it. MODEL 552 Before you even unpack your new Remington firearm, read this Stock instruction book from cover to cover and familiarize yourself with the different component parts of the firearm. Then read, understand and follow the Ten Commandments of Firearm Safety in this book. WARNING! Discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition may result in exposure to lead, a substance known to cause birth defects, reproductive harm, cancer and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure. SHOOT SOBER!! Im There's one other rule that must be followed when handling firearms. In fact, respect for this rule is necessary in order to effectively practice the Ten Commandments of Firearm Safety. The rule is: SHOOT SOBER! Firearms and alcohol or Th drugs make a deadly combination. Never consume anything that would mildly impair your judgment or physical coor- dination when you're using a firearm. A staggering percentage of the shooting accidents that occur every year involve The alcohol or drugs. Be smart. Always shoot sober and stay alive. See WARNING! Failure to follow any of these safety rules may cause personal injury or death to the shooter or bystander The s and damage to property. Do not use a firearm until you fully understand and practice the Ten Commandments of disch Firearm Safety. If you have any questions about the safe use of a Remington firearm, write to us at Remington Arms order Company, LLC , Consumer Service, P.O. Box 700, Madison, NC 27025-0700, or call us at 1-800-243-9700. To en DON'T KEEP THIS TO YOURSELF. MAR Now that you're a firearm owner you have the obligation to help ensure that shooting sports are safe for everyone - Alwa participants and bystanders alike. You can do that by practicing these principles of firearm safety and passing them on to others - especially new shooters. Set an example for beginners. Be a guide to their safe entry into the exciting world do n of shooting sports. Invest your time and patience for the love of the sport and for its future. After all, it's your love of Neve the sport that led you to buy a new Remington. Whe Firearm ownership is a right and privilege. It's a right guaranteed in this nation's Constitution. It's a privilege, which ING. carries with it a personal responsibility to use your firearm in a way which will ensure your safety and the safety of kept others. The preservation of this right and privilege depends on the personal commitment of you and your fellow ally r shooters to the safe and responsible use of firearms. Let the Ten Commandments of Firearm Safety outlined in the book guide you at all times. Teach and promote these rules whenever you can. Remember, firearm safety depends on WAR you! That's the only way to really enjoy your new Remington firearm and to preserve sport shooting as we know it BAN today. Even the f

6 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 7

® ™ ™ For safe and dependable operation of your firearm, all parts of your firearm must be properly cleaned and lubri- Remington Model 572 Pump Action Rimfire Rifle and Model 552 cated. Periodically inspect the internal workings of your firearm to be sure they're clean and free of rust, unwant- Autoloading Rimfire Rifle ed dirt and debris. Congratulations on your choice of a Remington.® With proper care, it should give you many years of dependable Use recommended lubricants on your firearm and do not over-lubricate. The use of a non-recommended lubricant use and enjoyment. For best results, we recommend that you use Remington Ammunition – the ammunition used could adversely affect the function and safe operation of your firearm. Remember, you are responsible for the proper in factory testing your firearm against our exacting function and performance standards. care and maintenance of your firearm. Failure to properly maintain your firearm cannot only damage or ruin your ™ ™ firearm, it can expose you and others to unnecessary risks of personal injury or death. PICTURE 1 A These pictures show the main parts of the REMINGTON MODEL 572 PUMP ACTION RIMFIRE RIFLE AND THE MODEL 552 AUTOLOADING RIMFIRE RIFLE. The picture will aid in understanding the instructions in this book. Remington® has a wide range of firearm care products and resources for best results when cleaning your firearm. ™ MODEL 572 Receiver Rear Sight Barrel Front Sight Everything from solvents and lubricants to rods and patches. They're all available from your Remington dealer. Ejection Port Stock

Fore-end Muzzle LEARN THE MECHANICS AND HANDLING CHARACTERISTICS OF YOUR FIREARM. Loading Port Magazine Tube Knurled Plug Not all firearms are alike. They have different mechanical characteristics that dictate how you should carry and handle Safety Mechanism Trigger Action Bar Lock them. Anyone who plans to use a firearm should first become totally familiar with the type of firearm it is and the safe Operating Handle Rear Sight handling procedures for loading, unloading, carrying, shooting and PICTURE 1 B Receiver Ejection Port Barrel Front Sight ™ On Left Side storing it. MODEL 552 Before you even unpack your new Remington firearm, read this Stock instruction book from cover to cover and familiarize yourself with the Loading Port Operating Handle Fore-End Muzzle different component parts of the firearm. Then read, understand and Magazine Tube Knurled Plug follow the Ten Commandments of Firearm Safety in this book. Deflector Trigger WARNING! Discharging firearms in poorly ventilated areas, cleaning Safety Mechanism firearms or handling ammunition may result in exposure to lead, a substance known to cause birth defects, reproductive harm, cancer PICTURE 2 This picture shows the main parts of the ammunition. 22 CALIBER CARTRIDGE and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure. BULLET RIM SHOOT SOBER!! Important Parts of the Firearm There's one other rule that must be followed when handling firearms. In fact, respect for this rule is necessary in order 22 22 22 to effectively practice the Ten Commandments of Firearm Safety. The rule is: SHOOT SOBER! Firearms and alcohol or The Safety Mechanism SHORT LONG LONG RIFLE CASE drugs make a deadly combination. Never consume anything that would mildly impair your judgment or physical coor- dination when you're using a firearm. A staggering percentage of the shooting accidents that occur every year involve The safety mechanism on the Model 572™ and Model 552™ Rimfire Rifle is a button located behind the trigger. alcohol or drugs. Be smart. Always shoot sober and stay alive. See Pictures 3 and 4. PICTURE 3 WARNING! Failure to follow any of these safety rules may cause personal injury or death to the shooter or bystander The safety mechanism provides protection against accidental or unintentional and damage to property. Do not use a firearm until you fully understand and practice the Ten Commandments of discharge under normal usage when properly engaged and in good working Firearm Safety. If you have any questions about the safe use of a Remington firearm, write to us at Remington Arms order. Company, LLC , Consumer Service, P.O. Box 700, Madison, NC 27025-0700, or call us at 1-800-243-9700. To engage the safety mechanism, push the button so that the RED BAND DON'T KEEP THIS TO YOURSELF. MARKING CANNOT BE SEEN. Now that you're a firearm owner you have the obligation to help ensure that shooting sports are safe for everyone - Always engage the safety mechanism when the firearm is loaded and you SAFETY MECHANISM participants and bystanders alike. You can do that by practicing these principles of firearm safety and passing them on to others - especially new shooters. Set an example for beginners. Be a guide to their safe entry into the exciting world do not intend to shoot. of shooting sports. Invest your time and patience for the love of the sport and for its future. After all, it's your love of Never pull the trigger when the safety mechanism is engaged. the sport that led you to buy a new Remington. When you are ready to fire the firearm, press the safety mechanism so that the RED BAND MARKING IS SHOW- Firearm ownership is a right and privilege. It's a right guaranteed in this nation's Constitution. It's a privilege, which ING.Do not touch the trigger while moving the safety mechanism. Your fingers and all other objects should be carries with it a personal responsibility to use your firearm in a way which will ensure your safety and the safety of kept outside the trigger guard and away from the trigger until you are actu- PICTURE 4 others. The preservation of this right and privilege depends on the personal commitment of you and your fellow ally ready to fire by pulling the trigger. shooters to the safe and responsible use of firearms. Let the Ten Commandments of Firearm Safety outlined in the book guide you at all times. Teach and promote these rules whenever you can. Remember, firearm safety depends on WARNING: The firearm will fire when the trigger is pulled and the RED you! That's the only way to really enjoy your new Remington firearm and to preserve sport shooting as we know it BAND IS SHOWING. today. Even when the safety mechanism is engaged, careless handling can cause the firearm to fire. See the Ten Commandments of Firearm Safety on page 2. TRIGGER

6 7 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 8

The Security System The firearm you have purchased is equipped with either an integrated security system or with a separate lock- TO REMOVE THE INNER MAGAZINE TUBE: ing device. WARNING: Check the chamber and magazine to make sure there are no The separate locking device included with your firearm will be packaged with its own instructions. cartridges in the firearm. The integrated security system locking device instructions are described below. 1. Point the firearm in a safe direction. The security system enables the owner to lock the safety mechanism on the firearm in the “SAFE” position 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. with the use of a special key. 3. Unlock the inner magazine tube by turning the knurled plug at the THIS SECURITY SYSTEM DOES NOT ELIMINATE THE NEED FOR SAFE GUN HANDLING AND STORAGE, end of the tube. See Picture 8. INCLUDING KEEPING THIS AND EVERY GUN UNLOADED AND LOCKED IN A SECURE PLACE WHEN NOT 4. Pull the inner magazine tube from magazine tube. IN USE. READ AND FOLLOW THESE AND OTHER SAFETY RULES IN THIS INSTRUCTION BOOK. FAIL- URE TO READ, UNDERSTAND AND OBEY THESE RULES CAN RESULT IN SERIOUS PERSONAL INJURY OR DEATH TO YOU OR OTHERS. SEE THE TEN COMMANDMENTS OF FIREARM SAFETY ON PAGE 2. The Trigger Assembly Integrated Security System: Pulling the trigger fires the firearm. On the safety mechanism there is a “J” shaped slot. See Picture 5. This “J” slot is the key hole for securing your safety mechanism. Also on the safety mechanism is a pointer which will point and line up with either the The weight of the trigger pull is preset at the factory. RED or WHITE DOT on the trigger plate when the safety mechanism is turned. See Picture 5. The position of All adjustments to the trigger and trigger plate assembly must be made the pointer indicates whether or not the security system is engaged. The existence of the security system does by the factory or a REMINGTON® AUTHORIZED SERVICE CENTER. not change the basic operation of the safety mechanism, nor does it change the manner in which the safety mechanism should be used. WARNING: NEVER put your finger on the trigger unless you are going to fire the firearm. With your new firearm you will receive a capped key. To use the key remove the cap. On the key is an indicator The Barrel line which will line up with the pointer on the safety mechanism. See Picture 5. The inside of the barrel must be clean and free of obstructions. To engage the security system, press the safety mechanism to the “SAFE” position so the RED BAND DOES TO CHECK THE INSIDE OF THE BARREL ON THE MODEL 552: NOT SHOW. Insert the key into the “J” slot as far as it can go. Next, turn the key counter-clockwise so that the indicator line on the key and the pointer on the safety mechanism line up with the WHITE DOT on the WARNING: Look into the ejection port. Check the chamber and magazine to make sure there are no cartridges trigger plate. in the firearm. THE SECURITY SYSTEM IS NOW ENGAGED. 1. Point the firearm in a safe direction. In operating the security system, NEVER use excessive force to turn the key. If the key will not turn freely, 2. Engage the safety mechanism. Make sure the RED BAND IS NOT SHOWING. contact a Remington® Authorized Service Center. 3. Pull the operating handle fully rearward and hold fully rearward. Keep your security system engaged and your safety INDICATOR LINE 4. Insert a cleaning rod into the muzzle. Push the rod completely through the barrel until the rod can be seen mechanism in the “SAFE” position when your RED DOT firearm is not in use. Keep your key in a secure in the ejection port. place, inaccessible to others. DO NOT leave your key TO CHECK THE INSIDE OF THE BARREL ON THE MODEL 572: or any ammunition with your firearm, which should be kept unloaded and locked in a safe place. WARNING: Look into the ejection port. Check the chamber and magazine to make sure there are no cartridges in the firearm. If you lose the key, DO NOT attempt to disengage the “J” SLOT safety mechanism using a foreign object. This will KEY WHITE DOT 1. Point the firearm in a safe direction. damage your firearm. Contact your Remington PICTURE 5 2. Engage the safety mechanism. Make sure the RED BAND IS NOT SHOWING. Authorized Service Center for a replacement key. 3. Pull the fore-end fully rearward. Even if you think the security system and safety mechanism are engaged, careless handling can cause the firearm to fire. See the Ten Commandments of Firearm Safety on page 2. 4. Insert a cleaning rod into the muzzle. Push the rod completely through the barrel until the rod can be The Operating Handle (Model 552) seen in the ejection port. PICTURE 6 TO REMOVE OBJECT FROM INSIDE THE BARREL: The operating handle is on the left-hand side of the Model 552 and is OPERATING HANDLE used to pull the bolt rearward to open the action. See Picture 6. WARNING: Never try to remove an object from the barrel by loading another cartridge and firing. This may WARNING: When the operating handle is forward as shown in Picture cause the barrel to burst or a cartridge case to rupture and cause serious personal injury. 6, the bolt is closed and is in the ready-to-fire position. 1. Use the correct size cleaning rod. The Fore-End 2. Insert the cleaning rod into the muzzle and lightly tap rod to free object. The fore-end on the Model 572 is used to pull the bolt rearward. To 3. Push the cleaning rod all the way through the barrel, until the rod can be seen in the ejection port. open the action, push up on the action bar lock and pull the fore-end 4. If an object cannot be easily pushed out of the barrel with a cleaning rod, return the firearm to the factory rearward. See Picture 7. or a REMINGTON AUTHORIZED SERVICE CENTER. WARNING: When the fore-end is fully forward as shown in Picture 7, the bolt is closed and is in the ready- to-fire position.

8 9 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 9

The Security System PICTURE 7 The firearm you have purchased is equipped with either an integrated security system or with a separate lock- TO REMOVE THE INNER MAGAZINE TUBE: ing device. WARNING: Check the chamber and magazine to make sure there are no The separate locking device included with your firearm will be packaged with its own instructions. cartridges in the firearm. The integrated security system locking device instructions are described below. 1. Point the firearm in a safe direction. The security system enables the owner to lock the safety mechanism on the firearm in the “SAFE” position 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. FORE-END with the use of a special key. 3. Unlock the inner magazine tube by turning the knurled plug at the THIS SECURITY SYSTEM DOES NOT ELIMINATE THE NEED FOR SAFE GUN HANDLING AND STORAGE, end of the tube. See Picture 8. ACTION BAR LOCK INCLUDING KEEPING THIS AND EVERY GUN UNLOADED AND LOCKED IN A SECURE PLACE WHEN NOT 4. Pull the inner magazine tube from magazine tube. IN USE. READ AND FOLLOW THESE AND OTHER SAFETY RULES IN THIS INSTRUCTION BOOK. FAIL- PICTURE 8 URE TO READ, UNDERSTAND AND OBEY THESE RULES CAN RESULT IN SERIOUS PERSONAL INJURY OR DEATH TO YOU OR OTHERS. SEE THE TEN COMMANDMENTS OF FIREARM SAFETY ON PAGE 2. The Trigger Assembly Integrated Security System: Pulling the trigger fires the firearm. On the safety mechanism there is a “J” shaped slot. See Picture 5. This “J” slot is the key hole for securing your safety mechanism. Also on the safety mechanism is a pointer which will point and line up with either the The weight of the trigger pull is preset at the factory. RED or WHITE DOT on the trigger plate when the safety mechanism is turned. See Picture 5. The position of All adjustments to the trigger and trigger plate assembly must be made MAGAZINE TUBE the pointer indicates whether or not the security system is engaged. The existence of the security system does by the factory or a REMINGTON® AUTHORIZED SERVICE CENTER. KNURLED PLUG not change the basic operation of the safety mechanism, nor does it change the manner in which the safety mechanism should be used. WARNING: NEVER put your finger on the trigger unless you are going to fire the firearm. With your new firearm you will receive a capped key. To use the key remove the cap. On the key is an indicator The Barrel line which will line up with the pointer on the safety mechanism. See Picture 5. The inside of the barrel must be clean and free of obstructions. To engage the security system, press the safety mechanism to the “SAFE” position so the RED BAND DOES TO CHECK THE INSIDE OF THE BARREL ON THE MODEL 552: NOT SHOW. Insert the key into the “J” slot as far as it can go. Next, turn the key counter-clockwise so that the indicator line on the key and the pointer on the safety mechanism line up with the WHITE DOT on the WARNING: Look into the ejection port. Check the chamber and magazine to make sure there are no cartridges trigger plate. in the firearm. THE SECURITY SYSTEM IS NOW ENGAGED. 1. Point the firearm in a safe direction. In operating the security system, NEVER use excessive force to turn the key. If the key will not turn freely, 2. Engage the safety mechanism. Make sure the RED BAND IS NOT SHOWING. contact a Remington® Authorized Service Center. 3. Pull the operating handle fully rearward and hold fully rearward. Keep your security system engaged and your safety 4. Insert a cleaning rod into the muzzle. Push the rod completely through the barrel until the rod can be seen mechanism in the “SAFE” position when your firearm is not in use. Keep your key in a secure in the ejection port. place, inaccessible to others. DO NOT leave your key TO CHECK THE INSIDE OF THE BARREL ON THE MODEL 572: or any ammunition with your firearm, which should be kept unloaded and locked in a safe place. WARNING: Look into the ejection port. Check the chamber and magazine to make sure there are no cartridges in the firearm. If you lose the key, DO NOT attempt to disengage the safety mechanism using a foreign object. This will 1. Point the firearm in a safe direction. damage your firearm. Contact your Remington 2. Engage the safety mechanism. Make sure the RED BAND IS NOT SHOWING. Authorized Service Center for a replacement key. 3. Pull the fore-end fully rearward. Even if you think the security system and safety mechanism are engaged, careless handling can cause the firearm to fire. See the Ten Commandments of Firearm Safety on page 2. 4. Insert a cleaning rod into the muzzle. Push the rod completely through the barrel until the rod can be The Operating Handle (Model 552) seen in the ejection port. PICTURE 6 TO REMOVE OBJECT FROM INSIDE THE BARREL: The operating handle is on the left-hand side of the Model 552 and is used to pull the bolt rearward to open the action. See Picture 6. WARNING: Never try to remove an object from the barrel by loading another cartridge and firing. This may WARNING: When the operating handle is forward as shown in Picture cause the barrel to burst or a cartridge case to rupture and cause serious personal injury. 6, the bolt is closed and is in the ready-to-fire position. 1. Use the correct size cleaning rod. The Fore-End 2. Insert the cleaning rod into the muzzle and lightly tap rod to free object. The fore-end on the Model 572 is used to pull the bolt rearward. To 3. Push the cleaning rod all the way through the barrel, until the rod can be seen in the ejection port. open the action, push up on the action bar lock and pull the fore-end 4. If an object cannot be easily pushed out of the barrel with a cleaning rod, return the firearm to the factory rearward. See Picture 7. or a REMINGTON AUTHORIZED SERVICE CENTER. WARNING: When the fore-end is fully forward as shown in Picture 7, the bolt is closed and is in the ready- to-fire position.

8 9 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:33 AM Page 10

TO CLEAN THE BARREL FOLLOW THE INSTRUCTIONS SHOWN ON PAGE 12. To Load The Model 572 BEFORE LOADING THE FIREARM: Make sure the inside of the barrel is free of dirt or other objects. I. TO LOAD ONE CARTRIDGE ONLY: To Load The Model 552 WARNING: Always check the cartridge for the correct caliber before loading the firearm. WARNING: Always check the cartridges for the correct caliber before loading the firearm. NOTE: The chamber should be cleaned before loading and firing the firearm the first time. Follow cleaning instructions shown on page 12. I. TO LOAD ONE CARTRIDGE ONLY: 1. Check the chamber and magazine to make sure there are no cartridges in the firearm. NOTE: The chamber should be cleaned before loading and firing the firearm the first time. Follow cleaning instructions 2. Point the firearm in a safe direction throughout the loading shown on page 12. process. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. 1. Check the chamber and magazine to make sure there are no car- PICTURE 9 tridges in the firearm. 4. Pull the fore-end fully rearward to open the action. 2. Point the firearm in a safe direction throughout the loading 5. Put one cartridge of the correct caliber through the ejection port process. and into the chamber. See Picture 11. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. 6. Keep your fingers away from the ejection port. 4. Pull the operating handle fully rearward and hold. 7. Push the fore-end forward close the action. 5. Put one cartridge of the correct caliber through the ejection port THE FIREARM IS NOW LOADED WITH A ROUND IN THE CHAMBER. and into the chamber. See Picture 9. 8. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. 6. Keep your fingers away from the ejection port. EJECTION PORT THE FIREARM IS NOW READY TO FIRE 7. Release the operating handle to close the action. 9. Pull the trigger to fire the firearm. 10. Engage the safety mechanism when you are finished firing. RED BAND WILL NOT SHOW. THE FIREARM IS NOW LOADED WITH A ROUND IN THE CHAMBER. II. TO LOAD THE CHAMBER AND MAGAZINE: 8. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. WARNING: Always check the cartridge for the correct caliber before loading the firearm. THE FIREARM IS NOW READY TO FIRE. 1. Check the chamber and magazine to make sure there are no cartridges in the firearm. 9. Pull the trigger to fire the firearm. 2. Point the firearm in a safe direction throughout the loading process. 10. Engage the safety mechanism when you are finished firing. RED BAND WILL NOT SHOW. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. II. TO LOAD THE CHAMBER AND MAGAZINE: 4. Unlock the inner magazine tube by turning the knurled plug at the end of the tube. PICTURE 10 5. Pull the inner magazine forward from the magazine tube until the loading port is open. See Picture 10. 1. Check the chamber and magazine to make sure there are no car- LOADING PORT 6. Insert cartridges through the loading port, bullet end forward towards the muzzle. tridges in the firearm. MUZZLE 7. Load magazine to capacity, tubular magazine will hold 20 shorts, 17 long or 15 long rifle cartridges. 2. Point the firearm in a safe direction throughout the loading 8. Close the loading port in the magazine by sliding the inner magazine tube back into the magazine. process. NOTE: Turn the tube slightly to ease passage over loaded cartridges. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. 9. Turn the tube clockwise to lock the inner magazine to the magazine tube. 4. Unlock the inner magazine tube by turning the knurled plug at the IMPORTANT: Inner magazine tube will not lock properly if to many cartridges are loaded into the magazine. end of the tube. MAGAZINE FOLLOWER 10. Pull the fore-end fully rearward and then push the fore-end fully forward. This will close the action and 5. Pull the inner magazine forward from the magazine tube until the load a cartridge from the magazine into the chamber. loading port is open. See Picture 10. THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED. 6. Insert cartridges through the loading port, bullet end forward towards the muzzle. 11. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. 7. Load magazine to capacity, tubular magazine will hold 20 shorts, 17 long or 15 long rifle cartridges. 8. Close the loading port in the magazine by sliding the inner magazine tube back into the magazine. THE FIREARM IS NOW READY TO FIRE. NOTE: Turn the tube slightly to ease passage over loaded cartridges. 12. Pull the trigger to fire the firearm. 13. Pull the fore-end fully rearward to eject the empty cartridge. 14. Slide the fore-end 9. Turn the tube clockwise to lock the inner magazine to the magazine tube. forward to chamber the next cartridge. 15. IMPORTANT: Inner magazine tube will not lock properly if too many cartridges are loaded into the magazine. Engage the safety mechanism when you are finished firing. RED 10. Pull the operating handle fully rearward and release. This will load a cartridge from the magazine into the BAND WILL NOT SHOW. chamber. THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED. To Unload the Firearm (Model 552 and 11. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. Model 572) 1. Point the firearm in a safe direction throughout the unloading THE FIREARM IS NOW LOADED AND READY TO FIRE. process. 12. The firearm will fire each time the trigger is pulled until the magazine and chamber are empty. 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. 13. Engage the safety mechanism when you are finished firing. RED BAND WILL NOT SHOW. 3. Turn the knurled plug to unlock the inner magazine tube from the magazine tube. 4. Pull the inner magazine tube completely from the magazine tube. 5. Tilt the muzzle down to allow the cartridges to slide from the mag- azine.

10 11 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 11

TO CLEAN THE BARREL FOLLOW THE INSTRUCTIONS SHOWN ON PAGE 12. To Load The Model 572 BEFORE LOADING THE FIREARM: Make sure the inside of the barrel is free of dirt or other objects. I. TO LOAD ONE CARTRIDGE ONLY: To Load The Model 552 WARNING: Always check the cartridge for the correct caliber before loading the firearm. WARNING: Always check the cartridges for the correct caliber before loading the firearm. NOTE: The chamber should be cleaned before loading and firing the firearm the first time. Follow cleaning instructions shown on page 12. I. TO LOAD ONE CARTRIDGE ONLY: 1. Check the chamber and magazine to make sure there are no cartridges in the firearm. NOTE: The chamber should be cleaned before loading and firing the firearm the first time. Follow cleaning instructions 2. Point the firearm in a safe direction throughout the loading PICTURE 11 shown on page 12. process. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. 1. Check the chamber and magazine to make sure there are no car- PICTURE 9 tridges in the firearm. 4. Pull the fore-end fully rearward to open the action. 2. Point the firearm in a safe direction throughout the loading 5. Put one cartridge of the correct caliber through the ejection port process. and into the chamber. See Picture 11. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. 6. Keep your fingers away from the ejection port. EJECTION PORT 4. Pull the operating handle fully rearward and hold. 7. Push the fore-end forward close the action. 5. Put one cartridge of the correct caliber through the ejection port THE FIREARM IS NOW LOADED WITH A ROUND IN THE CHAMBER. and into the chamber. See Picture 9. 8. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. 6. Keep your fingers away from the ejection port. EJECTION PORT THE FIREARM IS NOW READY TO FIRE 7. Release the operating handle to close the action. 9. Pull the trigger to fire the firearm. 10. Engage the safety mechanism when you are finished firing. RED BAND WILL NOT SHOW. THE FIREARM IS NOW LOADED WITH A ROUND IN THE CHAMBER. II. TO LOAD THE CHAMBER AND MAGAZINE: 8. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. WARNING: Always check the cartridge for the correct caliber before loading the firearm. THE FIREARM IS NOW READY TO FIRE. 1. Check the chamber and magazine to make sure there are no cartridges in the firearm. 9. Pull the trigger to fire the firearm. 2. Point the firearm in a safe direction throughout the loading process. 10. Engage the safety mechanism when you are finished firing. RED BAND WILL NOT SHOW. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. II. TO LOAD THE CHAMBER AND MAGAZINE: 4. Unlock the inner magazine tube by turning the knurled plug at the end of the tube. PICTURE 10 5. Pull the inner magazine forward from the magazine tube until the loading port is open. See Picture 10. 1. Check the chamber and magazine to make sure there are no car- 6. Insert cartridges through the loading port, bullet end forward towards the muzzle. tridges in the firearm. 7. Load magazine to capacity, tubular magazine will hold 20 shorts, 17 long or 15 long rifle cartridges. 2. Point the firearm in a safe direction throughout the loading 8. Close the loading port in the magazine by sliding the inner magazine tube back into the magazine. process. NOTE: Turn the tube slightly to ease passage over loaded cartridges. 3. Engage the safety mechanism. RED BAND WILL NOT SHOW. 9. Turn the tube clockwise to lock the inner magazine to the magazine tube. 4. Unlock the inner magazine tube by turning the knurled plug at the IMPORTANT: Inner magazine tube will not lock properly if to many cartridges are loaded into the magazine. end of the tube. 10. Pull the fore-end fully rearward and then push the fore-end fully forward. This will close the action and 5. Pull the inner magazine forward from the magazine tube until the load a cartridge from the magazine into the chamber. loading port is open. See Picture 10. THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED. 6. Insert cartridges through the loading port, bullet end forward towards the muzzle. 11. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. 7. Load magazine to capacity, tubular magazine will hold 20 shorts, 17 long or 15 long rifle cartridges. 8. Close the loading port in the magazine by sliding the inner magazine tube back into the magazine. THE FIREARM IS NOW READY TO FIRE. NOTE: Turn the tube slightly to ease passage over loaded cartridges. 12. Pull the trigger to fire the firearm. 13. Pull the fore-end fully rearward to eject the empty cartridge. 14. Slide the fore-end 9. Turn the tube clockwise to lock the inner magazine to the magazine tube. forward to chamber the next cartridge. 15. IMPORTANT: Inner magazine tube will not lock properly if too many cartridges are loaded into the magazine. Engage the safety mechanism when you are finished firing. RED PICTURE 12 10. Pull the operating handle fully rearward and release. This will load a cartridge from the magazine into the BAND WILL NOT SHOW. chamber. THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED. To Unload the Firearm (Model 552 and 11. To prepare to fire, disengage the safety mechanism. RED BAND WILL SHOW. Model 572) 1. Point the firearm in a safe direction throughout the unloading THE FIREARM IS NOW LOADED AND READY TO FIRE. process. MAGAZINE TUBE 12. The firearm will fire each time the trigger is pulled until the magazine and chamber are empty. 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. 13. Engage the safety mechanism when you are finished firing. RED BAND WILL NOT SHOW. 3. Turn the knurled plug to unlock the inner magazine tube from the magazine tube. 4. Pull the inner magazine tube completely from the magazine tube. 5. Tilt the muzzle down to allow the cartridges to slide from the mag- azine.

10 11 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 12

Shake the firearm slightly to make sure all cartridges slide MODEL 552 PICTURE 13 time, until the patch is not dirty. from the magazine. See Picture 12. 6. Replace and lock the inner magazine tube. 7. Push a clean patch saturated with Rem™ Oil through the barrel. WARNING: Two cartridges may remain in the rifle after the magazine is 8. Push a clean, dry patch through the barrel to remove excess lubri- unloaded - one in the chamber and one in the action. To unload those cant. cartridges: 9. Apply a thin coat of Rem™ Oil to the outside of the barrel with a 7a. Model 552 soft, clean cloth. Pull the operating handle fully rearward to extract and eject the WARNING: After cleaning, make sure the barrel is free of obstructions. round from the chamber and repeat as many times as necessary to MAGAZINE FOLLOWER unload any rounds from the action. How To Disassemble 7b. Model 572 To Disassemble The Model 552: Pull the fore-end fully rearward and repeat as many times as neces- MODEL 572 PICTURE 14 WARNING: NEVER attempt to disassemble a loaded firearm. sary to extract and eject the round from the chamber and any rounds Check the chamber and magazine to make sure there are no car- from the action. tridges in the firearm. WARNING: Visually check the chamber, action and magazine to make 1. Point the firearm in a safe direction. sure there are no cartridges in the firearm. 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. NOTE: The end of the magazine follower can be seen when the action is 3. Tap out the front and rear trigger plate pins. See Picture 16. open and the last cartridge is removed from the action. See Picture 13 MAGAZINE FOLLOWER 4. Lift and remove the trigger plate assembly from the receiver. and 14. 5. Unscrew the take-down screw. See Picture 17. To Adjust the Sights REAR SIGHT APERTURE 6. Separate the fore-end slightly from the receiver. WARNING: NEVER adjust the sights on a loaded firearm. Make sure PICTURE 15 the chamber and magazine are completely unloaded before adjusting WINDAGE SCREW 7. Grasp the fore-end firmly to the barrel and pull the barrel and bolt the sights Also make sure the safety mechanism is engaged. RED assembly from the receiver. See Picture 17. BAND WILL NOT SHOW. 8. Slide the action bar from the bolt slot. See Picture 18. 9. Pull the bolt assembly from the barrel. TO ADJUST THE REAR SIGHT: To Disassemble The Model 572: For elevation (up and down adjustments) and windage (left and right WARNING: NEVER attempt to disassemble a loaded firearm. adjustments), move the rear sight in the same direction as you need to REAR SIGHT SLIDE Check the chamber and magazine to make sure there are no car- move the bullet on the target. See Picture 15. ELEVATION SCREW tridges in the firearm. NOTE: For more information on ballistics and trajectory, see the 1. Point the firearm in a safe direction. REMINGTON® catalog. POSITION ON ADJUSTMENTS 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. TARGET TELESCOPIC SIGHTS: 3. Tap out the front and rear trigger plate pins. See Picture 16. 4. Lift and remove the trigger plate assembly from the receiver. The receiver is designed with two long dovetail grooves cut into a. Loosen the elevation screw 5. Unscrew and remove the barrel dowel screw and washer. See the top panel. A receiver type mount may be used. Slide the on the rear sight. b. Slide the rear sight down Picture 19. mount into the grooves and tighten in the desired location. (backward) on the ramp. 6. Unscrew and remove the barrel lock screw. Bullets hits above c. Tighten the elevation screw. TO CLEAN THE BARREL: the center. 7. Separate the fore-end slightly from the receiver. WARNING: NEVER attempt to clean the barrel on a loaded a. Loosen the elevation screw 8. Grasp the fore-end firmly to the barrel and pull the barrel and bolt firearm. Check the chamber and magazine to make sure there on the rear sight. assembly from the receiver. See Picture 20. are no cartridges in the firearm. b. Slide the rear sight up 9. Lift the action bar lug from the bolt. See Picture 21. (forward) on the ramp. 10. Pull the bolt assembly from the barrel. 1. Use the instructions and the equipment provided in a good Bullets hits below c. Tighten the elevation screw. cleaning kit. For recommendations, see your the center. CLEANING AND LUBRICATION: Remington Authorized Service Center. a. Loosen the windage screw WARNING: NEVER attempt to clean or lubricate a loaded firearm. 2. Select the correct caliber cleaning brush and attach the on the rear sight. Check the chamber and magazine to make sure there are no car- brush to the cleaning rod. b. Slide the rear sight aperture tridges in the firearm. to the right. 3. Put the cleaning brush into the gun cleaning solvent. Bullets hits to c. Tighten the windage screw. Actr ion Ba 4. Push the cleaning brush through the barrel several times. the left. 1. Brush with gun cleaning solvent and wipe dry with a clean cloth. 2. Apply a thin coat of Rem™ Oil to prevent rusting. NOTE: Always clean the barrel from the muzzle to the chamber. a. Loosen the windage screw on the rear sight. Bolt Assembly 5. Remove the brush from the rod. Attach tip with correct size b. Slide the rear sight aperture 1. Brush with gun cleaning solvent and wipe dry with a clean cloth. cleaning patch and push through the bore. to the left. Bullets hits to c. Tighten the elevation screw. 2. Apply a thin coat of Rem™ Oil to prevent rusting. 6. Repeat several times using a new cleaning patch each the right.

12 13 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 13

Shake the firearm slightly to make sure all cartridges slide PICTURE 13 time, until the patch is not dirty. from the magazine. See Picture 12. PICTURE 16 6. Replace and lock the inner magazine tube. 7. Push a clean patch saturated with Rem™ Oil through the barrel. TRIGGER PLATE ASSEMBLY WARNING: Two cartridges may remain in the rifle after the magazine is 8. Push a clean, dry patch through the barrel to remove excess lubri- unloaded - one in the chamber and one in the action. To unload those cant. cartridges: 9. Apply a thin coat of Rem™ Oil to the outside of the barrel with a 7a. Model 552 soft, clean cloth. Pull the operating handle fully rearward to extract and eject the WARNING: After cleaning, make sure the barrel is free of obstructions. round from the chamber and repeat as many times as necessary to MAGAZINE FOLLOWER TRIGGER PLATE PINS unload any rounds from the action. How To Disassemble To Disassemble The Model 552: 7b. Model 572 OPERATING HANDLE PICTURE 17 Pull the fore-end fully rearward and repeat as many times as neces- PICTURE 14 WARNING: NEVER attempt to disassemble a loaded firearm. sary to extract and eject the round from the chamber and any rounds Check the chamber and magazine to make sure there are no car- from the action. tridges in the firearm. WARNING: Visually check the chamber, action and magazine to make 1. Point the firearm in a safe direction. sure there are no cartridges in the firearm. 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. NOTE: The end of the magazine follower can be seen when the action is 3. Tap out the front and rear trigger plate pins. See Picture 16. RECEIVER BUSHING open and the last cartridge is removed from the action. See Picture 13 RECEIVER 4. Lift and remove the trigger plate assembly from the receiver. TAKEDOWN SCREW and 14. 5. Unscrew the take-down screw. See Picture 17. To Adjust the Sights 6. Separate the fore-end slightly from the receiver. BOLT SLOT PICTURE 18 WARNING: NEVER adjust the sights on a loaded firearm. Make sure PICTURE 15 the chamber and magazine are completely unloaded before adjusting 7. Grasp the fore-end firmly to the barrel and pull the barrel and bolt the sights Also make sure the safety mechanism is engaged. RED assembly from the receiver. See Picture 17. BAND WILL NOT SHOW. 8. Slide the action bar from the bolt slot. See Picture 18. 9. Pull the bolt assembly from the barrel. TO ADJUST THE REAR SIGHT: To Disassemble The Model 572: ACTION BAR For elevation (up and down adjustments) and windage (left and right WARNING: NEVER attempt to disassemble a loaded firearm. adjustments), move the rear sight in the same direction as you need to REAR SIGHT SLIDE Check the chamber and magazine to make sure there are no car- BARREL DOWEL SCREW PICTURE 19 move the bullet on the target. See Picture 15. ELEVATION SCREW tridges in the firearm. AND WASHER NOTE: For more information on ballistics and trajectory, see the 1. Point the firearm in a safe direction. REMINGTON® catalog. POSITION ON ADJUSTMENTS 2. Engage the safety mechanism. RED BAND WILL NOT SHOW. TARGET TELESCOPIC SIGHTS: 3. Tap out the front and rear trigger plate pins. See Picture 16. 4. Lift and remove the trigger plate assembly from the receiver. The receiver is designed with two long dovetail grooves cut into a. Loosen the elevation screw 5. Unscrew and remove the barrel dowel screw and washer. See the top panel. A receiver type mount may be used. Slide the on the rear sight. b. Slide the rear sight down Picture 19. mount into the grooves and tighten in the desired location. BARREL LOCK SCREW (backward) on the ramp. 6. Unscrew and remove the barrel lock screw. TO CLEAN THE BARREL: c. Tighten the elevation screw. 7. Separate the fore-end slightly from the receiver. BARREL PICTURE 20 BOLT WARNING: NEVER attempt to clean the barrel on a loaded a. Loosen the elevation screw 8. Grasp the fore-end firmly to the barrel and pull the barrel and bolt firearm. Check the chamber and magazine to make sure there on the rear sight. assembly from the receiver. See Picture 20. are no cartridges in the firearm. b. Slide the rear sight up 9. Lift the action bar lug from the bolt. See Picture 21. (forward) on the ramp. 1. Use the instructions and the equipment provided in a good c. Tighten the elevation screw. 10. Pull the bolt assembly from the barrel. cleaning kit. For recommendations, see your CLEANING AND LUBRICATION: ACTION BAR Remington Authorized Service Center. WARNING: NEVER attempt to clean or lubricate a loaded firearm. FORE-END a. Loosen the windage screw RECEIVER BUSHING 2. Select the correct caliber cleaning brush and attach the on the rear sight. Check the chamber and magazine to make sure there are no car- brush to the cleaning rod. b. Slide the rear sight aperture tridges in the firearm. to the right. ACTION BAR LUG PICTURE 21 3. Put the cleaning brush into the gun cleaning solvent. c. Tighten the windage screw. Action Bar EXTRACTOR 4. Push the cleaning brush through the barrel several times. 1. Brush with gun cleaning solvent and wipe dry with a clean cloth. 2. Apply a thin coat of Rem™ Oil to prevent rusting. NOTE: Always clean the barrel from the muzzle to the chamber. a. Loosen the windage screw on the rear sight. Bolt Assembly BOLT 5. Remove the brush from the rod. Attach tip with correct size b. Slide the rear sight aperture 1. Brush with gun cleaning solvent and wipe dry with a clean cloth. cleaning patch and push through the bore. to the left. MAGAZINE FOLLOWER c. Tighten the elevation screw. 2. Apply a thin coat of Rem™ Oil to prevent rusting. 6. Repeat several times using a new cleaning patch each FORE-END HANGER

13 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 14

Receiver Assembly NOTE: If the inner magazine tube is in the rifle, make sure the flexible magazine follower re-enters the receiver 1. Brush the inside of the receiver with gun cleaning solvent and wipe dry with a clean cloth. freely. 2. Apply a thin coat of Rem™ Oil to prevent rusting. 7. Align the fore-end hanger screw hole with the barrel lock screw hole in the receiver. Trigger Plate Assembly SPRAY WITH REM ™ OIL PICTURE 22 8. Replace and tighten the take-down screw. NOTE: Clean the trigger plate assembly as a unit. AS SHOWN 9. Replace and tighten barrel dowel screw and washer. 1. Spray the trigger plate assembly with Rem™ Oil as shown. 10. Replace the trigger plate assembly. Make sure the hammer in the cocked position. See Picture 24. See Picture 22. 11. Carefully guide projecting carrier and action bar lock into the receiver. See Picture 22. 2. Let stand for 15 minutes. NOTE: Check to make sure that the end of the action bar lock is below the end of the left connector. See 3. Spray again to wash off components. Picture 24. 4. Shake off excess lubrication. 12. Tap in the front and rear trigger plate pins. WARNING: Excessive use of a non-recommended lubricant could adversely affect the function and safe operation of your firearm. Lubrication For safe and dependable operation Over-lubrication should be avoided of your firearm, the barrel and action To Reassemble at all times. A light application of must be cleaned periodically. RemTM Oil helps to prevent rusting. To Reassemble The Model 552: Remington recommends using Bolt to Barrel WARNING! Excessive use of a lubri- Remington cleaning products and 1. Align the extractors in the bolt to re-enter the extractor slots in the barrel. cant could adversely affect the func- lubricants or their equivalents. 2. Slide the bolt into the barrel. tion and safe operation of your WARNING! The use of a non recom- NOTE: The bolt must be replaced into the barrel with the action bar lug slot facing the action bar. firearm. Failure to properly maintain your mended lubricant or cleaner could 3. Position the action bar lug in the matching slot in the bolt. firearm can not only adversely affect the function and safe 4. With the action bar engaging the the bolt, hold the fore-end and barrel firmly together. damage your firearm, it operation of your firearm. Do not use 5. Slide the barrel, assembled bolt, and action bar into the receiver. can expose you and oth- congealing lubricants. The use of 6. Seat the fore-end hanger (within the fore-end) firmly into non-congealing lubricants such as PROJECTING CARRIER PICTURE 23 ers to unnecessary risks the receiver. of personal injury or death. Rem™ Oil is strongly recommended. NOTE: If the inner magazine tube is in the rifle, make sure the HAMMER IN COCKED POSITION When the firearm is to be stored, it NOTE: Remington’s Rem™ Oil is flexible magazine follower re-enters the receiver freely. should be carefully cleaned and thor- available from your local dealer. If oughly oiled. Outside metal surfaces your dealer is out of stock, ask the 7. Align the fore-end hanger screw hole with the take-down should be wiped with RemTM Oil occa- dealer to order Rem™ Oil from the screw hole in the receiver. sionally. When the firearm is to be Remington Distributor. 8. Replace and tighten the take-down screw. reused, all excess lubrication must 9. Replace the trigger plate assembly. Make sure the hammer DISCONNECTOR be removed. The chamber and bore is in the cocked position. See Picture 21. LEFT CONNECTOR must be thoroughly wiped dry. 10. Carefully guide projecting carrier and disconnector into the receiver. See Picture 23. NOTE: Check to make sure that the end of the disconnector is below the end of the left connector. See Picture 23. 11. Tap in the front and rear trigger plate pins. PROJECTING CARRIER PICTURE 24 HAMMER IN COCKED To Reassemble The Model 572: POSITION Bolt to Barrel 1. Align the extractors in the bolt to re-enter the extractor slots in the barrel. 2. Slide the bolt into the barrel. NOTE: The bolt must be replaced into the barrel with the action bar lug slot facing the action bar. ACTION BAR LOCK LEFT CONNECTOR 3. Position the action bar lug in the matching slot in the bolt. 4. With the action bar engaging the the bolt, hold the fore-end and barrel firmly together. 5. Slide the barrel, assembled bolt, and action bar into the receiver. 6. Seat the fore-end hanger (within the fore-end) firmly into the receiver.

14 15 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 15

Receiver Assembly NOTE: If the inner magazine tube is in the rifle, make sure the flexible magazine follower re-enters the receiver 1. Brush the inside of the receiver with gun cleaning solvent and wipe dry with a clean cloth. freely. 2. Apply a thin coat of Rem™ Oil to prevent rusting. 7. Align the fore-end hanger screw hole with the barrel lock screw hole in the receiver. Trigger Plate Assembly PICTURE 22 8. Replace and tighten the take-down screw. NOTE: Clean the trigger plate assembly as a unit. 9. Replace and tighten barrel dowel screw and washer. 1. Spray the trigger plate assembly with Rem™ Oil as shown. 10. Replace the trigger plate assembly. Make sure the hammer in the cocked position. See Picture 24. See Picture 22. 11. Carefully guide projecting carrier and action bar lock into the receiver. See Picture 22. 2. Let stand for 15 minutes. NOTE: Check to make sure that the end of the action bar lock is below the end of the left connector. See 3. Spray again to wash off components. Picture 24. 4. Shake off excess lubrication. 12. Tap in the front and rear trigger plate pins. WARNING: Excessive use of a non-recommended lubricant could adversely affect the function and safe operation of your firearm. Lubrication For safe and dependable operation Over-lubrication should be avoided of your firearm, the barrel and action To Reassemble at all times. A light application of must be cleaned periodically. RemTM Oil helps to prevent rusting. To Reassemble The Model 552: Remington recommends using Bolt to Barrel WARNING! Excessive use of a lubri- Remington cleaning products and 1. Align the extractors in the bolt to re-enter the extractor slots in the barrel. cant could adversely affect the func- lubricants or their equivalents. 2. Slide the bolt into the barrel. tion and safe operation of your WARNING! The use of a non recom- NOTE: The bolt must be replaced into the barrel with the action bar lug slot facing the action bar. firearm. Failure to properly maintain your mended lubricant or cleaner could 3. Position the action bar lug in the matching slot in the bolt. firearm can not only adversely affect the function and safe 4. With the action bar engaging the the bolt, hold the fore-end and barrel firmly together. damage your firearm, it operation of your firearm. Do not use 5. Slide the barrel, assembled bolt, and action bar into the receiver. can expose you and oth- congealing lubricants. The use of 6. Seat the fore-end hanger (within the fore-end) firmly into ers to unnecessary risks non-congealing lubricants such as the receiver. of personal injury or death. Rem™ Oil is strongly recommended. NOTE: If the inner magazine tube is in the rifle, make sure the When the firearm is to be stored, it NOTE: Remington’s Rem™ Oil is flexible magazine follower re-enters the receiver freely. should be carefully cleaned and thor- available from your local dealer. If oughly oiled. Outside metal surfaces your dealer is out of stock, ask the 7. Align the fore-end hanger screw hole with the take-down should be wiped with RemTM Oil occa- dealer to order Rem™ Oil from the screw hole in the receiver. sionally. When the firearm is to be Remington Distributor. 8. Replace and tighten the take-down screw. reused, all excess lubrication must 9. Replace the trigger plate assembly. Make sure the hammer be removed. The chamber and bore is in the cocked position. See Picture 21. must be thoroughly wiped dry. 10. Carefully guide projecting carrier and disconnector into the receiver. See Picture 23. NOTE: Check to make sure that the end of the disconnector is below the end of the left connector. See Picture 23. 11. Tap in the front and rear trigger plate pins. PICTURE 24 To Reassemble The Model 572: Bolt to Barrel 1. Align the extractors in the bolt to re-enter the extractor slots in the barrel. 2. Slide the bolt into the barrel. NOTE: The bolt must be replaced into the barrel with the action bar lug slot facing the action bar. LEFT CONNECTOR 3. Position the action bar lug in the matching slot in the bolt. 4. With the action bar engaging the the bolt, hold the fore-end and barrel firmly together. 5. Slide the barrel, assembled bolt, and action bar into the receiver. 6. Seat the fore-end hanger (within the fore-end) firmly into the receiver.

14 15 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 16

MODEL 552™ MODEL 552™ Autoloading Rimfire Rifle Autoloading Rimfire Rifle PARTS LIST

62 61

30 47 72 60 31

45 46 29 48 8 17

32

59 8 7 22

21 16 3 20 41 4 19 18 12 42 23 27 50 13 44 40 51 37 49 14 39 71 70 1 35 43 2 6 34 28 5 38 15 36 33 57 56 67 24 69 58 25 53 66 54 68 52 26 9 10 55 64 65 11 63

16 17 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 17

MODEL 552™ MODEL 552™ Autoloading Rimfire Rifle Autoloading Rimfire Rifle PARTS LIST

VIEW# PART NAME VIEW# PART NAME NOTE: See Exploded View For Proper NOTE: Parts Subject To Change Without Identification Of Parts Notice FOB Ilion, New York. 1 Action Bar Assembly 48 Rear Sight Base Slide 2 Action Spring 49 Receiver (Restricted) 3 Barrel 50 Receiver Bushing 4 Bolt (Restricted) 51 Receiver Cover 5 Bolt Buffer 52 Safety Mechanism 6 Buffer Pad 53 Safety Mechanism Detent Ball 7 Butt Plate 54 Safety Mechanism Spring Butt Plate Insert (Not Shown) 55 Safety Mechanism Spring Retaining Pin 8 Butt Plate Screw 56 Sear Butt Plate Insert Screw (Not Shown) 57 Sear Pin 9 Carrier 58 Sear Spring 10 Carrier Pivot Tube 59 Stock Assembly 11 Carrier Spring 60 Stock Bolt 12 Cartridge Ramp 61 Stock Bolt Lock Washer 13 Deflector 62 Stock Bolt Washer 14 Deflector Screw 63 Take Down Screw 15 Disconnector 64 Trigger Assembly (Restricted) 16 Ejector (Includes: Connector Left, Connector 17 Elevation Screw Right, Connector Pin and Trigger 18 Extractor 65 Trigger Pin 19 Extractor Pin 66 Trigger Plate 20 Extractor Spring 67 Trigger Plate Pin Bushing, Rear 21 Extractor Spring Seat 68 Trigger Plate Pin Detent Spring, Front 22 Firing Pin 69 Trigger Plate Pin Detent Spring, Rear 23 Firing Pin Retaining Pin 70 Trigger Plate Pin, Front 24 Fore-End Assembly 71 Trigger Plate Pin, Rear 25 Fore-End Escutcheon 72 Windage Screw 26 Fore-End Escutcheon Nut 27 Fore-End Hanger 28 Fore-End Support 29 Front Sight 30 Front Sight Screw 31 Front Sight Washer 32 Grip Cap 28 33 Hammer 34 Hammer Pin Hammer Pin Washer (Not Shown) 35 Hammer Plunger 36 Hammer Spring 37 Inner Magazine Tube 38 Magazine Follower 39 Magazine Pin 40 Magazine Plug 41 Magazine Ring 42 Magazine Screw 43 Magazine Spring 44 Outer Magazine Tube 45 Rear Sight Aperture 46 Rear Sight Base 47 Rear Sight Base Screw

16 17 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 18

MODEL 572™ MODEL 572™ Pump Action Rimfire Rifle Pump Action Rimfire Rifle PARTS LIST

67 66 31 52 76 32 65

50 51 30 53 16 9 33

9 64 8 17 15 21 3 46 20 18

19 7 13 47 22 25 5 55 4 6

45 49 56 74 44 40 54 75 38 29 39 48 29 41 36 2 23 42 43 27 26 28 14 37 62 35 34 61 71 73 63 10

58 24 70 72 1 59 57 11 60 68 69 12

18 19 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 19

MODEL 572™ MODEL 572™ Pump Action Rimfire Rifle Pump Action Rimfire Rifle PARTS LIST

VIEW# PART NAME VIEW# PART NAME NOTE: See Exploded View For Proper NOTE: Parts Subject To Change Without Notice Identification Of Parts FOB Ilion, New York. 1 Action Bar 45 Magazine Plug 2 Action Bar Lock 46 Magazine Ring 3 Barrel 47 Magazine Screw 4 Barrel Dowel Screw 48 Magazine Spring 5 Barrel Dowel Screw Washer 49 Outer Magazine Tube 6 Barrel Lock Screw 50 Rear Sight Aperture 7 Bolt (Restricted) 51 Rear Sight Base 8 Butt Plate 52 Rear Sight Base Screw Butt Plate Insert (Not Shown) 53 Rear Sight Base Slide 9 Butt Plate Screw 54 Receiver (Restricted) Butt Plate Insert Screw (Not Shown) 55 Receiver Bushing 10 Carrier 56 Receiver Cover 11 Carrier Pivot Tube 57 Safety Mechanism 12 Carrier Spring 58 Safety Mechanism Detent Ball 13 Cartridge Ramp 59 Safety Mechanism Spring 13 Deflector 60 Safety Mechanism Spring Retaining Pin 14 Disconnector 61 Sear 15 Ejector 62 Sear Pin 16 Elevation Screw 63 Sear Spring 17 Extractor, Left 64 Stock Assembly 18 Extractor, Right 65 Stock Bolt 19 Extractor Pin 66 Stock Bolt Lock Washer (2) 20 Extractor Spring 67 Stock Bolt Washer 21 Firing Pin 68 Trigger Assembly (Restricted) 22 Firing Pin Retaining Pin (Includes: Connector Left, Connector 23 Fore-End Assembly Right, Connector Pin and Trigger 24 Fore-End Escutcheon 69 Trigger Pin 25 Fore-End Hanger 70 Trigger Plate 26 Fore-End Nut 71 Trigger Plate Pin Bushing, Rear 27 Fore-End Screw 72 Trigger Plate Pin Detent Spring, Front 29 28 Fore-End Lock Washer 73 Trigger Plate Pin Detent Spring, Rear 29 Fore-End Support (2) 74 Trigger Plate Pin, Front 30 Front Sight 75 Trigger Plate Pin, Rear 31 Front Sight Screw 76 Windage Screw 32 Front Sight Washer 33 Grip Cap 34 Hammer 35 Hammer Pin Hammer Pin Washer (Not Shown) 36 Hammer Plunger 37 Hammer Spring 38 Inner Magazine Tube 39 Locking Bar 40 Locking Bar Retaining Screw 41 Locking Bar Spring 42 Locking Bar Spring Stud 43 Magazine Follower 44 Magazine Pin

18 19 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 20

® Firearm Owner's Record How to Obtain Parts and Service From Remington Arms Co. How to Obtain Parts and Service From Repair Services TO ORDER PARTS: Remington Arms Company, LLC Many Remington Dealers and Authorized Service Centers carry a full line of parts. Please check with them first 1.To locate the Remington Authorized Model: before ordering parts. To Order Parts: Repair Center nearest you visit our web site at www.remington.com and use our To expedite your PARTS order or request REPAIR SERVICE visit our web site at www.remington.com. Detailed To order parts please visit Remington’s Repair Service Locator. If you need addi- Serial # instructions are provided along with parts and/or service order forms. You may also reach Remington by calling web site @ www.remingtonpartsstore.com tional on-line assistance, e-mail us at our toll free customer service number, 1-800-243-9700, Mon.-Fri., 9:00 AM-5:00 PM Eastern time. or call 1-800-243-9700. For additional [email protected] to obtain a listing of Date Purchased: 1. Fax completed order form (from the web site) to 1-336-548-7801. information on service enhancements, Authorized Repair Centers. Contact the upgrades, repair, additional barrels, and Authorized Repair Center of your choice Purchased From: 2. To order by phone without the order form call 1-800-243-9700. specialty parts visit www.remington.com. for evaluation of your firearm and/or addi- Please have the following information ready before you call. tional shipping instructions. Price Paid: • Firearm model and serial number. To place an order or for additional infor- 2.If your Remington Authorized Repair mation on service enhancements, up • Part description and quantity. Part descriptions can be found on the parts listing page in this manual. Center cannot provide the service or grades, and additional barrels, please repair you require and you need further Remember to complete and return the Firearm Warranty Registration Card in • Your complete mailing address (P.O. Box and Street Address) including zip code, telephone call us toll free consumer service number, assistance, please call our toll free num- order to obtain full benefit of your Limited Two Year Firearm Warranty. number and e-mail address. 1-800-243-9700, Mon.-Fri., 9:00 AM-5:00 ber 1-800-243-9700, Mon.-Fri., 9:00 AM- A WORD ON THE MAINTENANCE AND CARE OF YOUR REMINGTON FIREARM • Method of payment: Mastercard, Visa, Amex or Discover card number and expiration date. Prepayment PM Eastern time. 5:00 PM Eastern time and select the may be made by check or money order. A quote may be made to you over the phone. (Sorry, no C.O.D.s.) option for repairs. Don't Alter or Modify Your Firearm and Have it Serviced Regularly. WARNING! USE ONLY REMINGTON PARTS IN REMINGTON FIREARMS. 1. Fax completed order form (from the 3.If shipment of your firearm is required web site) to 1-336-548-7801. please follow the instructions below: Your firearm has been designed to operate Remington recommends that you have your NOTE: SOME PARTS MAY BE RESTRICTED. See parts list for details. Owner’s manuals/instruction books may be according to certain factory specifications. firearm professionally serviced annually. requested via our web site at: www.remington.com or by calling 1-800-243-9700. 2. To order by phone without the order form call 1-800-243-9700. • Record the serial number of your firearm You'll jeopardize your safety and that of You should also have your firearm profes- before shipping. Please have the following information ready others around you by attempting to alter its sionally serviced after prolonged storage, REPAIR SERVICES • Pack your firearm for safety and to pre- before you call. trigger, mechanical safety or other mecha- or if there is ever any question pertaining to 1. To locate the Remington Authorized Service Center nearest you visit our web site at www.remington.com and vent further damage in shipping and nisms. Never alter or modify your firearm the proper functioning characteristics of use our Repair Service Locator. If you need additional on-line assistance, e-mail us at [email protected] • Firearm model and serial number. handling. Preferably, ship in a firearm in any way. your firearm. to obtain a listing of Remington Authorized Service Centers. Contact the Remington Authorized Service • Part description and quantity. Part box. Center of your choice for evaluation of your firearm and/or additional shipping instructions. descriptions can be found on the parts • Remove all accessories from the firearm Like any mechanical device, a firearm is Proper cleaning and lubrication are also listing pages 26 through 29 in this manu- to prevent loss or damage. subject to wear. It must be maintained and important to firearm maintenance and are 2. If your Remington Authorized Service Center cannot provide the service or repair you require and you need al. • Enclose a letter with the firearm detail- periodically serviced to assure optimum necessary to assure accuracy, safety, and further assistance, please call our toll free number 1-800-243-9700, Mon.-Fri., 9:00 AM-5:00 PM Eastern • Your complete mailing address (P.O. ing the model name or number of your safety and performance. Only a qualified reliability. Before cleaning, always make time and select the option for repairs. Then, if shipment of your firearm is required, please: Box and Street Address) including zip firearm and serial number along with a service facility should service, repair or sure that your firearm is completely code, telephone number and e-mail full description of the problem. Be sure • Record the serial number of your firearm before sending it to us. modify your Remington firearm. Consult unloaded. And always clean the barrel from address. to include your full name and address your instruction manual for location of the the chamber end to the muzzle when possible. • Pack your firearm for safety and to prevent further damage in shipping and handling. Preferably, ship in a • Method of payment: MasterCard, Visa, (P.O. Box and Street Address), including nearest Authorized Remington Repair firearm box. Amex or Discover card number and zip code, daytime telephone number Center. • Remove all accessories from the firearm to prevent loss or damage. expiration date. A quote may be made and e-mail address. • Enclose a letter with the firearm detailing the model name or number of your firearm and serial number to you over the phone. (Sorry, no • Check your government guidelines along with a full description of the problem. Be sure to include your full name and address (P.O. Box and C.O.D.s.) before shipping. Firearm Sale or Transfer: • Remington is not responsible for dam- Street Address), including zip code, daytime telephone number and e-mail address. WARNING! Use only Remington parts in age or loss during shipment. You may • Ship your firearm by either United Parcel Service (UPS) or Parcel Post (US Post Office). Remington is not Remington’s firearms. If your firearm has been adjusted or changed in any way and you intend to sell or otherwise trans- elect to purchase insurance from your responsible for damage or loss during shipment, so you may elect to purchase insurance from your carrier. fer possession of your firearm, you must: 1) provide a complete service record, (2) warn the pur- NOTE: Some parts may be restricted. carrier. Ship to: See parts list for details. Owner's manu- chaser or recipient of your firearm that it has been adjusted or modified, and (3) give the purchas- Remington Arms Company, LLC WARNING! DO NOT SEND LIVE OR SPENT SHELLS IN YOUR FIREARM OR IN er or recipient this owner’s manual for review and reference. If you do not wish to sell or transfer THE SAME BOX WITH THE FIREARM. THIS IS A VIOLATION OF FEDERAL LAW. als/ instruction books may be requested Attn: Arms Service Division/Repairs via our web site at: www.remington.com your firearm in an adjusted condition (recommended), return it to a Remington Authorized Repair IF YOU FEEL YOU MUST SEND SPENT SHELLS, PLEASE SEND THEM IN A 14 Hoefler Ave. or by calling 1-800-243-9700. Center for restoration of your firearm to the original factory conditions. Do Not attempt to restore Ilion, NY 13357 SEPARATE PACKAGE AND INCLUDE NAME, ADDRESS (WITH ZIP CODE), the firearm to factory conditions yourself. TELEPHONE NUMBER, MODEL AND SERIAL NUMBER OF YOUR FIREARM. WARNING! Do not send live or spent shells in your firearm or in the same box with the WARNING! NEVER alter or modify any part of the firearm. Improper alterations can firearm. This is a violation of federal law. If you feel you must send spent shells, make the firearm unsafe and result in personal injury or death to you or others. please send them in a separate package and include name, address (with zip code), telephone number, model and serial number of your firearm. This firearm should not be sold where prohibited by federal, state or local laws.

20 21 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 21

Firearm Owner's Record How to Obtain Parts and Service From Repair Services Remington Arms Company, LLC 1.To locate the Remington Authorized Model: To Order Parts: Repair Center nearest you visit our web site at www.remington.com and use our To order parts please visit Remington’s Repair Service Locator. If you need addi- Serial # web site @ www.remingtonpartsstore.com tional on-line assistance, e-mail us at or call 1-800-243-9700. For additional [email protected] to obtain a listing of Date Purchased: information on service enhancements, Authorized Repair Centers. Contact the upgrades, repair, additional barrels, and Authorized Repair Center of your choice Purchased From: specialty parts visit www.remington.com. for evaluation of your firearm and/or addi- tional shipping instructions. Price Paid: To place an order or for additional infor- 2.If your Remington Authorized Repair mation on service enhancements, up Center cannot provide the service or grades, and additional barrels, please repair you require and you need further Remember to complete and return the Firearm Warranty Registration Card in call us toll free consumer service number, assistance, please call our toll free num- order to obtain full benefit of your Limited Two Year Firearm Warranty. 1-800-243-9700, Mon.-Fri., 9:00 AM-5:00 ber 1-800-243-9700, Mon.-Fri., 9:00 AM- A WORD ON THE MAINTENANCE AND CARE OF YOUR REMINGTON FIREARM PM Eastern time. 5:00 PM Eastern time and select the option for repairs. Don't Alter or Modify Your Firearm and Have it Serviced Regularly. 1. Fax completed order form (from the 3.If shipment of your firearm is required web site) to 1-336-548-7801. please follow the instructions below: Your firearm has been designed to operate Remington recommends that you have your 2. To order by phone without the order according to certain factory specifications. firearm professionally serviced annually. form call 1-800-243-9700. • Record the serial number of your firearm You'll jeopardize your safety and that of You should also have your firearm profes- before shipping. Please have the following information ready others around you by attempting to alter its sionally serviced after prolonged storage, • Pack your firearm for safety and to pre- before you call. trigger, mechanical safety or other mecha- or if there is ever any question pertaining to vent further damage in shipping and nisms. Never alter or modify your firearm the proper functioning characteristics of • Firearm model and serial number. handling. Preferably, ship in a firearm in any way. your firearm. • Part description and quantity. Part box. descriptions can be found on the parts • Remove all accessories from the firearm Like any mechanical device, a firearm is Proper cleaning and lubrication are also listing pages 26 through 29 in this manu- to prevent loss or damage. subject to wear. It must be maintained and important to firearm maintenance and are al. • Enclose a letter with the firearm detail- periodically serviced to assure optimum necessary to assure accuracy, safety, and • Your complete mailing address (P.O. ing the model name or number of your safety and performance. Only a qualified reliability. Before cleaning, always make Box and Street Address) including zip firearm and serial number along with a service facility should service, repair or sure that your firearm is completely code, telephone number and e-mail full description of the problem. Be sure modify your Remington firearm. Consult unloaded. And always clean the barrel from address. to include your full name and address your instruction manual for location of the the chamber end to the muzzle when possible. • Method of payment: MasterCard, Visa, (P.O. Box and Street Address), including nearest Authorized Remington Repair Amex or Discover card number and zip code, daytime telephone number Center. expiration date. A quote may be made and e-mail address. to you over the phone. (Sorry, no • Check your government guidelines C.O.D.s.) before shipping. Firearm Sale or Transfer: • Remington is not responsible for dam- WARNING! Use only Remington parts in age or loss during shipment. You may Remington’s firearms. If your firearm has been adjusted or changed in any way and you intend to sell or otherwise trans- elect to purchase insurance from your fer possession of your firearm, you must: 1) provide a complete service record, (2) warn the pur- NOTE: Some parts may be restricted. carrier. See parts list for details. Owner's manu- chaser or recipient of your firearm that it has been adjusted or modified, and (3) give the purchas- als/ instruction books may be requested er or recipient this owner’s manual for review and reference. If you do not wish to sell or transfer via our web site at: www.remington.com your firearm in an adjusted condition (recommended), return it to a Remington Authorized Repair or by calling 1-800-243-9700. Center for restoration of your firearm to the original factory conditions. Do Not attempt to restore the firearm to factory conditions yourself.

WARNING! Do not send live or spent shells in your firearm or in the same box with the WARNING! NEVER alter or modify any part of the firearm. Improper alterations can firearm. This is a violation of federal law. If you feel you must send spent shells, make the firearm unsafe and result in personal injury or death to you or others. please send them in a separate package and include name, address (with zip code), telephone number, model and serial number of your firearm. This firearm should not be sold where prohibited by federal, state or local laws.

20 21 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 22

Firearm Maintenance Record

DATE SERVICE PERFORMED PERFORMED BY DATE SERVICE PERFORMED PERFORMED BY

22 23 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 23

Firearm Maintenance Record Firearm Maintenance Record

DATE SERVICE PERFORMED PERFORMED BY DATE SERVICE PERFORMED PERFORMED BY

22 23 r1e7562rem_Q8:552/572 rev 706 3/21/12 9:34 AM Page 24

Remington is a trademark registered in the United States Patent and Trademark Office by Remington Arms Company, LLC

Part No. 3530 Printed in U.S.A. Form RD 7074 Rev. 0312