DIY Hydroponic Grow Box by Thefrosty on January 26, 2015

Total Page:16

File Type:pdf, Size:1020Kb

DIY Hydroponic Grow Box by Thefrosty on January 26, 2015 Food Living Outside Play Technology Workshop DIY Hydroponic Grow Box by TheFrosty on January 26, 2015 Table of Contents DIY Hydroponic Grow Box . 1 Intro: DIY Hydroponic Grow Box . 2 Materials Needed . 2 Possible Materials . 2 Step 1: Step 1: Building your Grow Box . 2 Step 2: Step 2: Spinkler System . 4 Step 3: Step 3: Adding Oxygen (optional) . 5 Step 4: Step 4: The Pump . 7 Step 5: Step 5: The Top . 7 Step 6: Enjoy! . 8 Related Instructables . 8 Advertisements . 8 Comments . 8 http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/ Author:TheFrosty My Blog! Husband,?A #WordPress developer, @FrostyMediaWP. I'm a photographer, Dodgers season ticket holder, softball player, gym enthusiast and drink aficionado. Intro: DIY Hydroponic Grow Box The original post can be found here: DIY Hydroponic Grow Box at Home After searching online for a hydroponic grow box I found a bunch of systems ranging from $200-$2000+. So I decided to build my own. Materials Needed Any size dark container bin (with lid). Use a size you’ve got the space for. I went with a 18 gal. dark gray bin from Home Depot. A submersible pump. GPH depends on size of tub, and your PVC sprinkler system. I went with a Hydrofarm 250-GPH Submersible Pump PVC pipe. I purchased ½” width with one t-joint fitting and two end caps. Which is slightly different then I’ve seen done in demo videos on YouTube (also different from initial photos – where my first build was with two L fittings with screw caps). Remember, it’s a DIY Hydroponic Box, and you can build it how every you see fit. Irrigation sprinkler heads. I picked up a 50 pack of red 360º micro sprayers on amazon after the 5 pack from Home Depot failed twice on me. The proper drill tap for your sprinkler head. Net cups. Size varies on bin size and number of cups in use. I would suggest the 2 to 3 inch cups for around 6-8 pots per bin. Clay (grow media). Can be found on Amazon or at your local grow shop.Rockwool Cubes or what I found to work better is the Aerogarden grow sponges. Flexible hose to attach pump to PVC sprinkler system (dishwasher hoses work best). Possible Materials Aquarium Air Pump with hoses, a one way check valve and a air stone. PVC pipe cutter Tape measure or a ruler PVC glue Epoxy Closet hanger “shelf” (holds the PVC tubing) Image Notes 1. PVC pipe cutter 2. Micro sprinkler head 3. Aquarium sub-pump 4. Dodgers duct-tape! Step 1: Step 1: Building your Grow Box After choosing your storage tub, measure down from the top the distance your PVC pipe with sprinkler heads plus the height of your net pots. This is where we’ll place the closet rod hangers. I also used a utility knife to scratch up the plastic to get the non-toxic epoxy/non-toxic hot glue to adhere the rod holders. If you’re comfortable you can screw it in, but remember to seal the hole with something as there will be water http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/ Image Notes Image Notes 1. Closet rod-hanger 1. Closet rod-hanger Image Notes 1. Scratched inner tub wall. http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/ Step 2: Step 2: Spinkler System Measure the width of the inner bin and then cut your PVC pipe to fit. In my bin I found the inner width to be 19?. I then measured the fittings; the t-joint was 2¾” wide and each end cap was 2¼ wide. With the subtraction of those totals to the total width and adding and eight (times each fitting entrance) I had my inner PVC length. Do a test fit with all the pieces together to make sure you’ve got the correct length and that it will fit nicely into the bin. Note: I found adding some hand lotion to the ends helps test fit the connections without them getting stuck together (I used some mini hotel lotions I had laying around for this). With everything still test fit together, mark your sprinkler head locations and drill your pilot holes and then tap them with the proper thread (usually supplied with your sprinkler head package – or at least listed so you can purchase the correct thread tap). Be sure the t-joint is pointing down. :) Image Notes Image Notes 1. Micro sprinkler head 1. In the final version I used a strait end cap. Image Notes 1. Strait end-cap. 2. Red micro 360º sprinkler heads. http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/ Step 3: Step 3: Adding Oxygen (optional) This step is not required as the sprinklers create a aeration effect. But I chose to add in two air-stones and a dual aquarium air-pump to introduce extra oxygen into the bin when the roots reach down and the hydroponics system becomes a deep water culture hydroponic box. Place the air-stone(s) at the bottom. I chose to glue them down and run the tubes up the side. I also drilled a small hole to run the tubes through in the top to allow the bin top to seat tight against the bin when closed. Also note the optional weather stripping around the top. Image Notes 1. Air-stone http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/ Image Notes 1. Air-stone 2. Air-tube running to air-pump. Image Notes Image Notes 1. Tube running through drilled hole in storage bin. 1. After installing weather sealant around bin top. http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/ Step 4: Step 4: The Pump Place the water pump at the bottom with the screw-in connection cap and measure out your flexible pipe to connect the pump to the PVC sprinkler system. Run the plug out the top (I cut the bin to allow the cable to run up and over to allow the top to seat flush). Notice the optional weather striping. Step 5: Step 5: The Top Now that the innards are complete, we need to cut the top to allow the net pots and an (optional) access hatch to add nutrients and additional water. I chose to flip the net cups upside down and measure the holes equally spaced around the top. Since the top is plastic, it will cut real easy with a sharp utility knife. After I cut the access hatch, I added some electrical tape to the bottom to re-enforce the swinging hatch. I then measured around the hatch and ended up with seven holes for pots. Image Notes Image Notes 1. Net-pot cutouts. 1. Final hydroponic bin top 2. Easy access hatch. 2. Wife... http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/ Image Notes Image Notes 1. Access hatch (in use) 1. Hydroton clay 2. Tomato plants (one month of growth) 2. Net-pot Step 6: Enjoy! Now go out and get your favorite vegetables and herbs a grow a garden! Let me know how your growing experience goes! Thanks! Austin Passy @TheFrosty Related Instructables Indoor Building an Aquaponics by Aquaponic Inverted Non-Circulating Mini Sprinkler jonathondk System by fox45 Hydroponics $10 homemade Hydroponics by Experiment by Herb Garden by hydroponic FLgrower rabidwoo grow light by kym.teo captainhydroponics Advertisements Comments 1 comments Add Comment Uncle Kudzu says: Jan 26, 2015. 3:35 PM REPLY Nicely done! Your grow box looks fairly easily doable and I'll bet it does a good job of keeping the roots hydrated and fed. Good Stuff! http://www.instructables.com/id/DIY-Hydroponic-Grow-Box/.
Recommended publications
  • Understanding Irrigation Decisions
    NUMBER 6 UNDERSTANDING IRRIGATION DECISIONS FROM ENTERPRISE PLANNING TO THE PADDOCK Kelvin Montagu, Ben Thomas, Geoff Thomas, Evan Christen, John Hornbuckle, Craig Baillie, Chris Linehan, Peter Smith, Fabian Gallo, Sam North, Wayne Meyer, Richard Stirzaker, Peter Cornish UNDERSTANDING IRRIGATION DECISIONS FROM ENTERPRISE PLANNING TO THE PADDOCK Kelvin Montagu, CRC Irrigation Futures Ben Thomas, Scholefield Robinson Horticultural Services Pty Ltd Geoff Thomas, Thomas Project Services Evan Christen, CSIRO, CRC for Irrigation Futures John Hornbuckle, CSIRO, CRC for Irrigation Futures Craig Baillie, CRC for Irrigation Futures Chris Linehan, Department of Primary Industries, Victoria Peter Smith, NSW Department of Primary Industries, CRC for Irrigation Futures Fabian Gallo, HydroTech Monitoring Pty Ltd Sam North, NSW Department of Primary Industries, CRC for Irrigation Futures Wayne Meyer, CSIRO, CRC for Irrigation Futures Richard Stirzaker, CSIRO, CRC for Irrigation Futures Peter Cornish, University of Western Sydney, CRC for Irrigation Futures i Published by: Land & Water Australia on behalf of the National Program for Sustainable Irrigation Postal address: GPO Box 2182 Canberra ACT 2601 Office Location: L1, The Phoenix Building 86 Northbourne Ave Braddon ACT Telephone: 02 6263 6000 Facsimile: 02 6263 6099 Email: Land&[email protected] Internet: www.lwa.gov.au © Land & Water Australia and IF Technologies Pty Ltd 2006. Acknowledgment The National Program for Sustainable Irrigation focuses research on the development and adoption of
    [Show full text]
  • Prototype Water Conservation Plan for the Department of Land and Natural Resources (Dlnr)
    PROTOTYPE WATER CONSERVATION PLAN FOR THE DEPARTMENT OF LAND AND NATURAL RESOURCES (DLNR) Prepared for: Commission on Water Resource Management Department of Land and Natural Resources State of Hawaii February 2005 FUKUNAGA AND ASSOCIATES, INC. Consulting Engineers 1388 Kapiolani Boulevard, Second Floor Honolulu, Hawaii 96814 (808) 944-1821 PROTOTYPE WATER CONSERVATION PLAN FOR THE DEPARTMENT OF LAND AND NATURAL RESOURCES (DLNR) Prepared for: Commission on Water Resource Management Department of Land and Natural Resources State of Hawaii February 2005 FUKUNAGA AND ASSOCIATES, INC. Consulting Engineers 1388 Kapiolani Boulevard, Second Floor Honolulu, Hawaii 96814 (808) 944-1821 TABLE OF CONTENTS Page 1. OVERVIEW 1-1 1.1. Hawaii’s Physical Environment 1-1 1.2. Hawaii’s Water Resource Challenges 1-2 2. PROJECT BACKGROUND 2-1 2.1. Bureau of Reclamation 2-1 2.2. BOR Water Conservation Field Services Program 2-1 2.3. Scoping of the DLNR Water Conservation Plan 2-2 2.3.1. BOR 9-Step Management Plan Format 2-2 2.3.2. Proposed Modifications to the BOR 9-Step Management Plan Format 2-4 3. PLAN APPROACH 3-1 3.1. Phase 1 – Description of Agency (DLNR) 3-1 3.2. Phase 2 – Inventory of Water Use Characteristics (Survey) 3-1 3.3. Phase 3 – Selected DLNR Facilities for Pilot Water Conservation Plan 3-1 3.4. Phase 4 – Development of Prototype Water Conservation Programs 3-3 3.5. Phase 5 – Summary and Recommendations 3-3 4. PHASE 1 – BACKGROUND INFORMATION ON THE DEPARTMENT OF LAND AND NATURAL RESOURCES 4-1 4.1. Background 4-1 4.2.
    [Show full text]
  • INFLUENCE of SEEDLING ESTABLISHMENT TECHNIQUES and IRRIGATION SYSTEMS on GROWTH, WATER USE EFFICIENCY and NUTRIENT CONTENT of RUBBER (Hevea Brasiliensis MUELL.ARG)
    UNIVERSITI PUTRA MALAYSIA INFLUENCE OF SEEDLING ESTABLISHMENT TECHNIQUES AND IRRIGATION SYSTEMS ON GROWTH, WATER USE EFFICIENCY AND NUTRIENT CONTENT OF RUBBER (Hevea brasiliensis MUELL.ARG) ABBA NABAYI FP 2016 14 INFLUENCE OF SEEDLING ESTABLISHMENT TECHNIQUES AND IRRIGATION SYSTEMS ON GROWTH, WATER USE EFFICIENCY AND NUTRIENT CONTENT OF RUBBER (Hevea brasiliensis MUELL.ARG) UPM By ABBA NABAYI COPYRIGHT Thesis submitted to the School of Graduate Studies, Universiti Putra Malaysia, in Fulfilment of the Requirements for the Degree of Master of Science © April 2016 COPYRIGHT All material contained within the thesis, including without limitation text, logos, icons, photographs and all other artwork, is copyright material of University Putra Malaysia unless otherwise stated. Use may be made of any material contained within the thesis for non-commercial purposes from the copyright holder. Commercial use of material may only be made with the express, prior, written permission of University Putra Malaysia. Copyright © Universiti Putra Malaysia UPM COPYRIGHT © DEDICATION TO MY BELOVED PARENTS, FRIENDS AND FAMILY UPM COPYRIGHT © Abstract of thesis presented to the Senate of Universiti Putra Malaysia in fulfilment of the requirement for the Degree of Master of Science INFLUENCE OF SEEDLING ESTABLISHMENT TECHNIQUES AND IRRIGATION SYSTEMS ON GROWTH, WATER USE EFFICIENCY AND NUTRIENT CONTENT OF RUBBER (Hevea brasiliensis MUELL.ARG) By ABBA NABAYI April 2016 Chairman : Christopher Teh Boon Sung, PhD Faculty : Agriculture UPM Rubber (Hevea brasiliensis) is an important crop in tropical Asian countries. In Malaysia, rubber contributes much to the economy of the country through latex production. Latex production requires seedlings that are disease-free, mature quickly and have high field survival rates.
    [Show full text]
  • Effects of Sprinkler Irrigation System and Water Use Efficiency (WUE)
    International Journal of Modern Agriculture, Volume 10, No.1, 2021 ISSN: 2305-7246 Effects of Sprinkler Irrigation System and Water Use Efficiency (WUE) Gaurav Kumar1 1 Department of Agriculture, Sanskriti University, Mathura Uttar Pradesh-281401, India. Corresponding author: N. N. Saxena Department of Agriculture, Sanskriti University, Mathura Uttar Pradesh-281401, India. Abstract Although the population of Egypt is over ninety million, It is unable to fulfill the food requirements as enough amount of water is not available for sufficient production of crops. In order for recognizing and implementing the steps to minimize water usage and improving the crop production techniques, this research is carried out into the farm fields of farmers in 2009 and 2010, 2010 and 2011 to evaluate the effectiveness and economy feasibility of the sprinkler irrigation system for the growth of the wheat crops. In the National Researches Centers and Development Station in Nubaria, two field studies were performed. Under sprinkler irrigation method the water related characteristics of the crops like wheat have been readied in the region. Treatments composed of two irrigation sprinklers, set sprinklers (S1) and the lateral hand motions (S2), and 3 levels of irrigation (IF1: only once in a whole week; IF2: only twice in the whole week, IF3: three times in a whole week). Also, the highest amount of net profit occurred under strong defined sprinkler irrigation scheme and irrigation size. The suggested sprinkler method and irrigation schedule for each case for winter wheat in the Nubaria is solid set sprinkler (S1) and three-fold irrigations per week (IF3). The method of sprinkler irrigation is most general method of adaptation of irrigation water that normally falls as rainfall.
    [Show full text]
  • Irrigation for Small Farms
    This page is intentionally blank. ii IRRIGATION FOR SMALL FARMS Author Dana Porter, Ph.D., P.E. Associate Professor and Extension Specialist – Agricultural Engineering Texas AgriLife Research and Extension Service Department of Biological and Agricultural Engineering Texas A&M System Acknowledgements This resource is made available through efforts in support of Texas Water Development Board Contract #1003581100, “Youth Education on Rainwater Harvesting and Agricultural Irrigation Training for Small Acreage Landowners” and through partial funding support from the USDA-ARS Ogallala Aquifer Program. Special thanks are extended to Brent Clayton, Extension Program Specialist, Department of Biological and Agricultural Engineering, for his dedicated and capable assistance in project management; to Justin Mechell, former Extension Program Specialist, Department of Biological and Agricultural Engineering, for his assistance in project management and contributions to this publication; to Thomas Marek, P.E., Senior Research Engineer, Texas AgriLife Research, for his technical review; and to Dr. Patrick Porter, Extension Entomologist/Integrated Pest Management Specialist, Texas AgriLife Extension Service, for his editorial assistance iii This page is intentionally blank. iv CONTENTS 1. Introduction………………………………………………………….……….………….. 1 2. Irrigation Options: Technologies and Methods…………………………….……...… 3 3. Crop Water Requirements …………………………………………….……….…… 19 4. Soil Moisture Management………………………………………..………….……… 31 5. Water Sources and Water Quality…………………………………..……….……… 37 6. Irrigation Best Management Practices……………………………………….……… 51 Educational programs of Texas AgriLife Extension Service are open to all people without regard to race, color, sex, disability, religion, age, or national origin. v This page is intentionally blank. vi 1. INTRODUCTION Water is often a limiting factor in crop production systems, where constraints may be primarily physical (water resource availability, capacity or quality); economic (costs of equipment and operation vs.
    [Show full text]
  • Tips for Irrigation Sprinkler Systems Tune-Up Checklist
    Town of Lincoln Water Department Tips for Irrigation Sprinkler Systems Tune-Up Checklist __________________________________________________________________ There is no better time than spring to make sure your automatic sprinkler system is ready for another season of efficient lawn and garden watering. Here are a few simple steps that will go a long way towards saving water and money. The most important thing to remember when turning on your sprinkler system is to turn on the water slowly. You can create a huge water hammer if you are not careful. A water hammer is a high-pressure surge that occurs when a valve is first opened. An initial pressure surge can result in pipe bursts and damaged valves. When restoring water to your sprinkler system, open the main water valve slowly to allow pipes to fill with water in a gradual and controlled manner, thus preventing a water hammer and costly damage. Always open the system shutoff valve slowly to let the system pressurize gradually. 1. Starting your sprinkler system while the ground is still frozen can result in damage to the pipes. Use a shovel to make sure that the soil is frost-free 12 inches deep. If it is still solid as a rock, then wait another week and test it again before starting the sprinkler system. 2. Run a check of the irrigation controls and programs. Make sure the date and time is correct, and that the settings are appropriate for your landscape’s watering needs. Keep a copy of your watering schedule nearby. 3. Check for debris that may block the flow of water from the sprinkler heads.
    [Show full text]
  • Sprinkler Planning & Installation Guide
    Do-It-Yourself Sprinkler Planning & Installation Guide Your beautiful landscape awaits... INTRODUctiON Do-It-Yourself Sprinkler Planning & Installation Guide TABLE OF CONTENts TWO SystEMS ARE BEttER THAN ONE Congratulations on your decision to install an automatic BEFORE YOU BEGIN........................1 irrigation system . An automatic irrigation system will help you create the landscape you’ve always wanted by making sure your plants get the water they need, just when they need it . USING THE TORO DESIGN SERVICE . .4 How many times have you forgotten to water your lawn, or worse yet, over-watered it and ended up with unsightly brown QUESTIONNAIRE . 5 spots and muddy puddles? You could be using up to 50% more water than your yard needs . That isn’t good for your lawn or your pocketbook . The solution is precision watering using PROPERTY PLAN LAYOUT SHEET..............6 an automatic irrigation system which can be adjusted to the individual needs of different plantings . You will get a thicker, greener lawn and more beautiful gardens, as you save time • TRADITIONAL IRRIGATION INSTALLATION . 1-12 and water . STEP 1 - Gather Required Information . 2. STEP 2 - Map Out Your System . 7. %#842! STEP 3 - Install It! . 9. TROUBLESHOOTING . 13 APPENDIX A-E . 14-16 FREQUENTLY ASKED QUESTIONS ............18 An example of traditional sprinkler-based and drip irrigation systems . This system uses automatic in-line valves . IRRIGATION INSTALLATION TIPS . 19 There are two different styles of irrigation systems you can use: traditional sprinkler-based systems and drip irrigation systems . The good news is you don’t have to choose between them because they work better together .
    [Show full text]
  • A Method for Promoting Microbial Activity in Soil
    (19) TZZ Z_¥¥ T (11) EP 2 601 833 A2 (12) EUROPEAN PATENT APPLICATION (43) Date of publication: (51) Int Cl.: 12.06.2013 Bulletin 2013/24 A01N 25/30 (2006.01) A01N 49/00 (2006.01) A01N 65/00 (2009.01) A01P 3/00 (2006.01) (2006.01) (2006.01) (21) Application number: 13000517.6 A01P 5/00 A01G 1/00 (22) Date of filing: 13.04.2010 (84) Designated Contracting States: (72) Inventors: AT BE BG CH CY CZ DE DK EE ES FI FR GB GR • Pullen, Erroll, M. HR HU IE IS IT LI LT LU LV MC MK MT NL NO PL 1729 Somerset West (ZA) PT RO SE SI SK SM TR • Pullen, Melvin, Donovan Burbank, CA 91504-2909 (US) (30) Priority: 09.09.2009 US 585232 (74) Representative: Kador & Partner (62) Document number(s) of the earlier application(s) in Corneliusstrasse 15 accordance with Art. 76 EPC: 80469 München (DE) 10716646.4 / 2 475 247 Remarks: (71) Applicant: Oro Agri, Inc This application was filed on 01-02-2013 as a Trophy Club, TX 76262 (US) divisional application to the application mentioned under INID code 62. (54) A method for promoting microbial activity in soil (57) The instant invention relates to a method for in- a composition comprising one or more surfactants and creasing or promoting microbial activity in soil by applying one or more high terpene based oils to the soil. EP 2 601 833 A2 Printed by Jouve, 75001 PARIS (FR) EP 2 601 833 A2 Description [0001] The instant application is a continuation-in-part of co-pending U.S.
    [Show full text]
  • Compendium on Climate-Smart Irrigation
    COMPENDIUM Climate-Smart Irrigation Compendium on Climate-Smart Irrigation Concepts, evidence and options for a climate- smart approach to improving the performance of irrigated cropping systems Compendium on Climate-Smart Irrigation Concepts, evidence and options for a climate- smart approach to improving the performance of irrigated cropping systems Charles Batchelor, Julian Schnetzer Global Alliance for Climate-Smart Agriculture Rome, 2018 CONTENTS CONTENTS .......................................................................................................... II FIGURES ............................................................................................................. VI PHOTOS ........................................................................................................... VIII TABLES ............................................................................................................... IX BOXES .................................................................................................................. X FOREWORD ......................................................................................................... XI ACKNOWLEDGEMENTS ...................................................................................... XII PREFACE .......................................................................................................... XIII LIST OF ACRONYMS ........................................................................................... XV EXECUTIVE SUMMARY ....................................................................................
    [Show full text]
  • Irrigation: Inspecting and Correcting Turf Irrigation System Problems Fact Sheet No
    Irrigation: Inspecting and Correcting Turf Irrigation System Problems Fact Sheet No. 4.722 Crop Series|Irrigation by C. Swift and R.D. Khalsa* Revised by Kurt Jones** Quick Facts The Procedure sprinkler riser stems should be at least • Proper maintenance of the 4 inches or greater in length. The following can be accomplished when irrigation system is critical to - Sprinkler heads that are too high may the water is first turned on at the beginning of ensure uniform application of be damaged when mowing. the irrigation season. Examine each irrigation water in turf areas. sprinkler to determine if: - Sprinkler heads that are too high or too • Are any pop-up spray heads, impact low are a tripping hazard. • Irrigation sprinkler heads sprinkler or rotor sprinkler, nozzles or - In order to lift or lower the sprinkler that tilt, are below grade, sprinkler bodies broken? These need head, you may need to adjust the plugged, or operate at the swing pipe or use a different length to be replaced with the same size and wrong pressure, etc. affect the nipple extension (Figure 7). Level manufacturer parts (Figure 2). application of irrigation water. • Are sprinkler filters clean? Replace the sprinkler body and back-fill with missing filters. sand. Remove the nozzle and flush the • Inspect underground sprinkler • Is the sprinkler head above or below sprinkler head. systems at least once a grade? See level sprinkler heads with the • Is the top of the irrigation sprinkler year to locate and correct top of the lawn (Figure 3). Use a bulls-eye head parallel with the slope of the lawn problems.
    [Show full text]
  • Hydraulics and Field Performance of a Novel Micro Sprinkler
    HYDRAULICS AND FIELD PERFORMANCE OF A NOVEL MICRO SPRINKLER By SOUMYA RANI, T (2010 - 18 - 106) DEPARTMENT OF LAND &WATER RESOURCES AND CONSERVATION ENGINEERING KELAPPAJI COLLEGE OF AGRICULTURAL ENGINEERING AND TECHNOLOGY TAVANUR - 679573, MALAPPURAM 2012 HYDRAULICS AND FIELD PERFORMANCE OF A NOVEL MICRO SPRINKLER By SOUMYA RANI, T (2010 - 18 - 106) THESIS Submitted in partial fulfilment of the requirement for the degree of MASTER OF TECHNOLOGY IN AGRICULTURAL ENGINEERING (Soil and Water Engineering) Faculty of Agricultural Engineering & Technology Kerala Agricultural University DEPARTMENT OF LAND &WATER RESOURCES AND CONSERVATION ENGINEERING KELAPPAJI COLLEGE OF AGRICULTURAL ENGINEERING AND TECHNOLOGY TAVANUR - 679573, MALAPPURAM 2012 DECLARATION I hereby declare that this thesis entitled “Hydraulics and field performance of a novel micro sprinkler” is a bonafide record of research done by me during the course of research and that the thesis has not previously formed the basis for the award of any degree, diploma, fellowship or other similar title, of any other University or Society. Tavanur Soumya Rani T Date: (2010 - 18 - 106) Dr. Sathian, K.K Date: Associate Professor Department of Land & Water Resources and Conservation Engineering KCAET, Kerala agricultural University Tavanur, Malappuram, Kerala CERTIFICATE Certified that this thesis, entitled “Hydraulics and field performance of a novel micro sprinkler” is a record of research work done independently by Ms. Soumya Rani T (2010- 18- 106) under my guidance and supervision and that it has not previously formed the basis for the award of any degree, diploma, fellowship or associateship to her. Tavanur Dr. Sathian, K.K Chairman Advisory Committee CERTIFICATE We, the undersigned, members of the advisory committee of Ms.
    [Show full text]
  • View Full Text-PDF
    Int.J.Curr.Microbiol.App.Sci (2020) Special Issue-11: 1115-1140 International Journal of Current Microbiology and Applied Sciences ISSN: 2319-7706 Special Issue-11 pp. 1115-1140 Journal homepage: http://www.ijcmas.com Review Article Precision-Smart Water Technologies for Improving Water Use Efficiency and Water Productivity under Concept of Sustainable Farming as in Climate Change Situations Raghuvir Singh Meena1, Ganga Ram Mali2, Komandla Venkatkiran Reddy3, B. Sri Sai Siddartha Naik4, Somdutt5, Tirunagari Rupesh6, Jitendra Singh Bamboriya7 and Swetha Dhegavath8 1Department of Agronomy, RCA, MPUAT, Udaipur, Rajasthan, India 2KVK Gudamalani, AU Jodhpur Rajasthan, India 3Department of Agronomy, College of Agriculture Rajendranagar, PJTSAU, Hyderabad, Telangana, India 4Department of Agronomy, RCA, MPUAT, Udaipur, Rajasthan, India 5Directorate of Research, SK Rajasthan Agricultural University, Bikaner Rajasthan, India 6Division of Soil Science and Agricultural Chemistry, ICAR-IARI, New Delhi, India 7Soil Science and Agricultural Chemistry, MPUAT, Udaipur, Rajasthan, India 8Department of Soil Science and Agricultural Chemistry, PJTSAU, Hyderabad, India *Corresponding author ABSTRACT Water is considered as the most critical resource for sustainable agricultural development worldwide. Irrigated areas will increase in forthcoming years, while fresh water supplies will be diverted from agriculture to meet the increasing demand of domestic use and industry. Furthermore, the efficiency of irrigation is very low, since less than 65 % of the applied water is actually used by the crops. Worldwide water management in irrigated and rain-fed agriculture is becoming more and more complex to overcome the expected water scarcity stress. The sustainable use of irrigation water is a priority for agriculture in arid areas. So, under scarcity conditions and climate change considerable effort has been devoted over time to introduce policies aiming to increase water efficiency based on the assertion that more can be achieved with K e yw or ds less water through better management.
    [Show full text]