DOCSLIB.ORG

Novel Possibilities in Chemical Pretreatment and Finishing Of

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Novel Possibilities in Chemical Pretreatment and Finishing Of Novel Possibilities in Chemical Pretreatment and Finishing of Cotton Fabrics Dissertation zur Erlangung des akademischen Grades eines Doktors der Naturwissenschaften – Dr. rer. nat. – vorgelegt von Vahid Ameri Dehabadi geboren in Kashan/Iran Institut für Deutsches Textilforschungszentrum Nord-West gGmbH der Universität Duisburg-Essen 2012 Die vorliegende Arbeit wurde im Zeitraum von Nov 2008 bis Juli 2012 im Arbeitskreis von Prof. Dr. Gutmann am Institut für Deutsches Textilforschungszentrum Nord-West gGmbH der Universität Duisburg-Essen durchgeführt. Tag der Disputation: 10.12.2012 Gutachter: Prof. Dr. Gutmann Prof. Dr. Ulbricht Vorsitzender: Prof. Dr. Spohr Erklärung Hiermit versichere ich, dass ich die vorliegende Arbeit mit dem Titel „Novel Possibilities in Chemical Pretreatment and Finishing of Cotton Fabrics ” selbst verfasst und keine außer den angegebenen Hilfsmitteln und Quellen benutzt habe, und dass die Arbeit in dieser oder ähnlicher Form noch bei keiner anderen Universität eingereicht wurde. Essen, im Juli 2012 Vahid Ameri Dehabadi Novel Possibilities in Chemical Pretreatment and Finishing of Cotton Fabrics Von der Fakultät für Chemie der Universität Duisburg-Essen zur Erlangung des akademischen Grades eines Doktors der Naturwissenschaften genehmigte Dissertation von Vahid Ameri Dehabadi Essen–DeutsChland Juli 2012 Acknowledgment I am heartily thankful to my supervisor Prof. Dr. JoChen Stefan Gutmann, whose enCouragement, guidanCe and support from the initial to the final level enabled me to develop an understanding of the subjeCt. I also must deClare my speCially thanks to retired Prof. Dr. ECkhard SChollmeyer, who had kindly helped and let me to Continue my study in University of Duisburg- Essen. I owe my deepest gratitude to Dr. Hans-Jürgen BusChmann and Dr. Klaus Opwis, who without their support, patienCe and guidanCe this study would not have been Completed. I am indebted to many of my Colleagues in Deutsches Textilforschungszentrum Nord-West e. V. to support me during Completion of this projeCt: Dr. Reiner Benken, Dr. Dirk Knittel, Dr. Torsten Textor, Dr. Thomas Mayer-Gall, Harald Fink, Ulrike Artz, Andrea FisCher, Leonie Derksen and Elke Roskothen. And finally, I would like to thank my dear wife, Nazanin, for her understanding and endless love, my family, speCially my mother, who are not by my side but their warm enCouragements from a long distanCe, my home Country, always warm me up to overCome the Challenge in my studies and my dear friends Habib ShalChian, Abbas Aghaei and Kamal Arass. Vahid Ameri Dehabadi To: my love Nazanin, my mother, & my father, whose memory is always with me Page | I Table of Contents List of Figures .................................................................................................... IV List of Tables ................................................................................................... VIII List of Equations ................................................................................................ IX Abstract ............................................................................................................. 1 1 Combination of Acid-Demineralization and Desizing of Cotton Fabrics by Using Acid-Stable Starch-Converting enzymes ............................................... 3 1.1 Introduction .............................................................................................. 4 1.2 State of research ........................................................................................ 6 1.2.1 Structure of cotton ................................................................................................ 6 1.2.2 Desizing of cotton ............................................................................................... 10 1.2.3 Acid demineralization ......................................................................................... 11 1.2.4 Enzymatic processes of textiles ........................................................................... 11 1.2.4.1 StruCture and funCtions of enzymes ........................................................... 11 1.2.4.2 EnzymatiC deComposition of hydrogen peroxide ........................................ 14 1.2.4.3 Biofinishing of CellulosiC fibers by Cellulases ............................................... 16 1.2.4.4 EnzymatiC sCouring of CellulosiC fibers ........................................................ 17 1.2.4.5 EnzymatiC bleaching of CellulosiC fibers ...................................................... 18 1.2.4.6 EnzymatiC finishing of protein fibers ........................................................... 19 1.2.4.7 EnzymatiC treatment of synthetiC fibers ..................................................... 20 1.2.4.8 EnzymatiC desizing of Cotton ....................................................................... 20 1.3 Aims of study ........................................................................................... 25 1.4 Basic approaches ..................................................................................... 26 1.5 Experimental ........................................................................................... 28 1.5.1 Materials ............................................................................................................. 28 1.5.1.1 Enzymes ...................................................................................................... 28 1.5.1.2 Cotton fabriC ............................................................................................... 28 1.5.1.3 Buffer solutions and other ChemiCals .......................................................... 28 1.5.2 Methods .............................................................................................................. 29 1.5.2.1 EnzymatiC desizing of Cotton fabriC ............................................................. 29 1.5.2.2 Evaluation of desizing performanCe ............................................................ 29 1.5.2.3 Measurement of the CationiC metals .......................................................... 30 Page | II 1.6 Results and discussion ............................................................................. 32 1.6.1 Evaluation of enzymatic desizing ........................................................................ 32 1.6.2 Using chelating agents in enzymatic desizing ..................................................... 43 1.6.3 Measurement of the remaining cationic metals ................................................. 51 2 Multifunctional Finishing of Cotton Fabrics Using Carboxylated Polyamines 57 2.1 Introduction ............................................................................................ 58 2.2 State of Research ..................................................................................... 61 2.2.1 Durable press finishing of cotton fabrics ............................................................. 61 2.2.1.1 Formaldehyde-based finishing agents ........................................................ 61 2.2.1.2 Formaldehyde-free finishing agents ........................................................... 64 2.2.1.3 PolyCarboxyliC acids as formaldehyde-free finishing agents ....................... 68 2.2.2 Flame retardant finishing of cotton fabrics ........................................................ 72 2.2.2.1 MeChanisms of flame retardants ................................................................ 72 2.2.2.2 Non-durable and semi-durable flame retardants ....................................... 76 2.2.2.3 Durable flame retardants ............................................................................ 78 2.3 Aim of study ............................................................................................ 83 2.4 Basic approaches ..................................................................................... 84 2.5 Materials and methods ............................................................................ 89 2.5.1 Materials ............................................................................................................. 89 2.5.2 Methods .............................................................................................................. 89 2.5.2.1 Carboxylation of polyvinylamine (PVAm) .................................................... 89 2.5.2.2 ChemiCal CharaCterization of Carboxylated PVAm ...................................... 89 2.5.2.3 Finishing of Cotton with Carboxylated PVAm .............................................. 90 2.5.2.4 GravimetriC test .......................................................................................... 90 2.5.2.5 FTIR spectrosCopy of finished Cotton fabriC ................................................ 91 2.5.2.6 Determination of CarboxyliC groups in finished Cotton with Carboxylated PVAm ........................................................................................................... 91 2.5.2.7 Measurement of free amino groups in treated Cotton ............................... 92 2.5.2.8 Dyeing with reaCtive dyes ........................................................................... 93 2.5.2.9 Measurement of wrinkle reCovery angle, tensile strength, whiteness index and wash fatness ......................................................................................... 93 2.5.2.10 Evaluation of fastness properties of dyed fabriCs ....................................... 93 2.5.2.11 Color measurement of dyed fabriCs ...........................................................
Load more

Recommended publications
  • Preparation of Cloth for Dyeing METHODOLOGY
    Preparation of Cloth for dyeing METHODOLOGY • PREPARATION OF CLOTH FOR DYEING • Grey cloth as it comes from the loom stage is unattractive and contains natural as well as added impurities, which hinders the successful operations of dyeing by reducing the absorbency of the fabric that’s why it is necessary to make the fabric water absorbent, by making the fabric free from any natural as well as added impurities in order to achieve successful dyeing process. • Preparation of the cotton cloth contains following steps systematically. Different Treatments to the fabric • Desizing • Scouring • Bleaching Desizing • Desizing is a process by which fatty matters are removed from the grey cloth i.e. starch etc., which applied to the warp and weft yarns during weaving in order to with stand the stress or strain. • Process of desizing can be done either by hydrolytic desizing or by oxidative desizing. • The theme of desizing process is only to convert the insoluble starch into soluble form. Starch can be hydrolyzed under the following steps: • Starch → Dextrin → Dextrin → Maltose → Glucose • (Insoluble) (Insoluble) (Soluble) (Soluble) (Soluble) Scouring • Scouring is the process by which oils, fats, waxes and other nitrogenous matters are removed. Process is carried out by adding 2g/l caustic soda, 1g/l soda ash and 1 g/l T.R.O. and then the temperature is raised to boil and process continued for 3‐4 hours under the pH 10‐ 11.5. Bleaching • A method of bleaching, the fabric is rinsed and struck against a stone, so as to remove as much of the sizing as possible.
    [Show full text]
  • Clean Trends in Textile Wet Processing Dalia F
    Science ile & Ibrahim, J Textile Sci Eng 2012, 2:5 xt e E T n f g i DOI: 10.4172/2165-8064.1000e106 o n l e a e n r r i n u Journal of Textile Science & Engineering g o J ISSN: 2165-8064 Editorial OpenOpen Access Access Clean Trends in Textile Wet Processing Dalia F. Ibrahim* Faculty of Applied Arts, Helwan University, Cairo, Egypt Textile industries are facing a challenging condition in the field of quality and productivity, due to the globalization of the world market. The highly competitive atmosphere and as the ecological parameters becoming more stringent, it becomes the prime concern of the textile processor to be conscious about quality and ecology. Again the guidelines for the textile processing industries by the pollution control boards create concern over the environment-friendliness of the processes, making it essential for innovations and changes in the processes [1]. Textile wet processing, is consider as a big and important sector in textile industry, with a wide range of procedures, which affect the final product appearance and quality. Wet processing occurs at various stages in the creation of textiles, as shown in Figure 1. This is the most widely used wet processing flow-chart on the Figure 2 contemporary textile industry. As textile industry is searching for innovative production techniques to improve the product quality, liquids and gaseous media. With reference to the properties of human as well as society requires new finishing techniques working in ear, high frequency inaudible oscillations are ultrasonic or supersonic. environmental respect [2]. In other words, while the normal range of human hearing is in between 16 Hz and 16 kHz, ultrasonic frequencies lie between 20 kHz and 500 Through this review article, we focus on the most innovated trends MHz.
    [Show full text]
  • Life Cycle Assessment of the Neutralization Process in a Textile WWTP
    Erciyes Üniversitesi Erciyes University Fen Bilimleri Enstitüsü Dergisi Journal of Institue Of Science and Technology Cilt 36, Sayı 3 , 2020 Volume 36, Issue 3, 2020 Life Cycle Assessment of the Neutralization Process in a Textile WWTP Fatma Şener Fidan *1, Emel Kızılkaya Aydoğan 1, Niğmet Uzal 2 *1 Erciyes University Engineering Faculty Department of Industrial Engineering, KAYSERI 2 Abdullah Gul University, Engineering Faculty Department of Civil Engineering, KAYSERI (Alınış / Received: 29.01.2020, Kabul / Accepted: 05.12.2020, Online Yayınlanma / Published Online: 31.12.2020) Keywords Abstract: Although industrial wastewater treatment plants (WWTP) have become Life Cycle Assessment, an important part of textile facilities in reducing environmental pollution Neutralization, problems, they also produce sludge and various emissions such as high chemical Sustainability, oxygen demand, color and conductivity which have serious negative impacts on Textile Industry, the environment. One of the processes with enormous chemical consumption in Wastewater treatment, industrial WWTP of textile facilities is the neutralization process, which aims to adjust the pH of the wastewater. Neutralization processes needed to be optimized in order to determine its overall environmental impacts and then identify the most environmentally appropriate options. The aim of this study is to compare the environmental impacts of carbon dioxide and sulfuric acid, which are two alternative chemicals used in the neutralization process of textile facilities, using Life Cycle Assessment (LCA) approach. The environmental impacts resulting from the use of these two chemicals proposed according to the Reference document on Best Available Techniques (BREF) Document for Textile Industry were revealed by the CML-IA method and the gate-to-gate method.
    [Show full text]
  • Feasibility Study of Integrated Desizing, Scouring and Bleaching
    European Scientific Journal November 2016 edition vol.12, No.33 ISSN: 1857 – 7881 (Print) e - ISSN 1857- 7431 Feasibility Study of Integrated Desizing, Scouring and Bleaching of Cotton Woven Fabric with H2O2 and Investigation of Various Physical Properties with Traditionally Treated Fabric Md. Golam Nur, Senior Lecturer Department of Textile Engineering, Primeasia University, Bangladesh M. Forhad Hossain, Associate Prof. Mustafijur Rahman, Lecturer Department of Wet Process Engineering, Bangladesh University of Textiles doi: 10.19044/esj.2016.v12n33p26 URL:http://dx.doi.org/10.19044/esj.2016.v12n33p26 Abstract Pre-treatment plays a significant role for the successful coloration of any kind of natural textile fiber like cotton, wool, flax, silk etc. This research work overview the influence of various types of traditional preparation techniques applied on cotton fiber before coloration such as desizing, scouring and bleaching. The traditional pre-treatment processes consume plenty of environmentally unfriendly chemicals those generate pollution in the effluents. In this research work an endeavour has been made to desize, scour and bleach grey cotton woven fabric simultaneously using caustic soda and hydrogen peroxide. The physical properties like whiteness, percent loss in fabric weight, tensile strength of the treated fabric have been compared with those of the fabric treated to conventional desizing, scouring and bleaching process. It is observed that the whiteness (ready for colouration) obtained by this process is quite satisfactory. Moreover, this process has some other merits such as ecological, economical, energy conserving and time saving aspect. Keywords: Desizing, Scouring, Bleaching, Pre-treatment, Hydrogen Peroxide Introduction Natural fibres like cotton, jute, flax, hemp, kenaf contain some inherent impurities such as oil, fat, wax and pectin within the fiber structure.
    [Show full text]
  • Water Pollution Reduction Through Recovery of Desizing Wastes
    .. WATER POLLUTION REDUCTION THROUGH RECOVERY OF DES IZI NG WASTES DEPARTMENT OF TEXTILE CHEMISTRY SCHOOL OF TEXTILES NORTH CAROLINA STATE UNIVERSITY RALEIGH, NORTH CAROLINA 27607 for the ENVIRONMENTAL PROTECTION AGENCY OFFICE OF RESEARCH AND MONITORING Project 12090 EOE January 1972 --- --- For sale by the Superintendent of Documents, U.S. Oovemment Printing Office, Wasblngton, D.C. 20402 - Prlce 60 cents This report has been reviewed by the Environnental Protec- ticn Agency and apprcYJe6 for publication. Approval does not sig:iify tnat the cofitents necessarily r-ef1ec-t the views and policies of the Envircnmntal Frotcction Agency, nor does mention of trade names or commercial products constitute endorsement or recomiendation for use. 3 ii ABSTRACT Processes for precipitating from desizing wastes the synthetic warp sizes, carboxymethyl cellulose ( CMC) and polyvinyl alcohol ( PVA) , were inve s tigate d. Carboxyme thy1 cellulose is precipitated quantitatively by certain multivalent metal salts, such as aluminum sulfate and ferric chloride. Aluminum sulfate is the more suitable for size recovery. Cycles of sizing, desizing and size recovery were performed on cotton- polyester ( 65:35) yarns, starting with commercial CMC, and continuing with only the recovered material. After four cycles, the performance of the recovered CMC on a Callaway slasher was satisfactory and results with the sized yarns on a warp-shed tester were equivalent to results with yarns sized with new CMC. Two copolymers of PVA were prepared, one of which was precipitated from dilute solution by aluminum sulfate and ferric chloride, the other by acidification, Preliminary sizing trials with small samples of mater- ials indicate that these, or similar, copolymers may be effective, recovera- ble warp sizes.
    [Show full text]
  • Denim Fabric Manufacturing
    TECHNICAL BULLETIN 6399 Weston Parkway, Cary, North Carolina, 27513 • Telephone (919) 678-2220 ISP 1010 DENIM FABRIC MANUFACTURING This report is sponsored by the Importer Support Program and written to address the technical needs of product sourcers. © 2004 Cotton Incorporated. All rights reserved; America’s Cotton Producers and Importers. PROCESS FLOW FOR DENIM MANUFACTURING The warp yarn (length-wise) used in denim fabrics is uniquely prepared for denim manufacturing compared to conventional woven fabrics. The yarn goes through numerous processing steps before it is placed on the weaving machine. Unlike the warp yarn, most filling yarn (width-wise) is put onto yarn packages and delivered directly to the weaving machine where it is inserted into the fabric without any further preparation in the same manner as conventional woven fabrics. The following flow chart reveals the necessary steps in the manufacture of denim fabrics, beginning with the production of the warp yarns used. The chart forms an outline for most of the topics that will be covered in this bulletin. Yarn Spinning Ball Warping Dye Beam Warping Beam Warping Rope Dyeing Beam Dyeing Slasher Dyeing Slashing (undyed) Re-Beaming Slashing Weaving Weaving Desizing Finishing Slashing Weaving Finishing Dyeing Weaving Finishing Finishing Finishing Finished Fabric Operations Figure 1. Process Flow for Warp Yarn in Denim Manufacturing 1 DENIM YARNS Yarn Numbering Refer to Cotton Incorporated’s technical bulletin entitled “Yarn Numbering Systems-TRI 1014” for further information on yarn numbering systems and how to convert from one system to another. Common Yarn Sizes for Denim Warp yarns for bottom weight jeans typically range in size from Ne 4.0 to Ne 12.5/1.
    [Show full text]
  • Plasma Technology & Its Application in Textile Wet Processing
    International Journal of Engineering Research & Technology (IJERT) Vol. 1 ISSN:Issue 5,2278-0181 July - 2012 PLASMA TECHNOLOGY & ITS APPLICATION IN TEXTILE WET PROCESSING S. K. Chinta*, S. M. Landage and Sathish Kumar. M D.K.T.E.Society‟s, Textile & Engineering Institute, Ichalkaranji, Maharashtra, India Abstract Plasma treatments are gaining popularity in the textile industry due to their numerous advantages over conventional wet processing techniques. The plasma treatment does not alter the bulk property. Plasma surface treatments show distinct advantages, because they are able to modify the surface properties of inert materials, sometimes with environment friendly devices. Application of “Plasma Technology” in chemical processing of textiles is one of the revolutionary ways to enhance the textile wet processing right from pretreatments to finishing. This paper deals with application of plasma technology for cotton pretreatment and finishing. Key words: Cotton, Dyeing, Finishing, Pretreatments, Plasma Technology 1. Introduction Textiles have undergone chemical processing since time immemorial. The textile industry is searching for innovative production techniques to improve the product quality, as well as society requires new 1 www.ijert.org 1 International Journal of Engineering Research & Technology (IJERT) Vol. 1 ISSN:Issue 5,2278-0181 July - 2012 finishing techniques working in environmental respect. Over recent years, physicochemical techniques have become more commercially attractive and have begun to overcome conventional wet chemical methods for property modification. The importance of surface modification of textile materials extends over a wide range of alterations or embedded selective additions, to provide desired single or multi features for various applications. It is a highly focused area of research in which alterations to physical and/or chemical properties lead to new textile products that provide new applications or satisfy specific needs.
    [Show full text]
  • Chemistry & Technology of Fabric Preparation & Finishing
    Chemistry & Technology of Fabric Preparation & Finishing by Dr. Charles Tomasino Department of Textile Engineering, Chemistry & Science College of Textiles North Carolina State University Raleigh, North Carolina CHEMISTRY & TECHNOLOGY OF FABRIC PREPARATION & FINISHING BY DR. CHARLES TOMASINO DEPARTMENT OF TEXTILE ENGINEERING, CHEMISTRY AND SCIENCE COLLEGE OF TEXTILES NORTH CAROLINA STATE UNIVERSITY All rights reserved. Copyright © 1992 by Charles Tomasino No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without permission in writing from the author PREFACE Global competition has caused the US textile industry to modernize and become cost competitive because developing nations have discovered that exporting textile products to the USA is an attractive way to enhance their economic growth. Their low labor costs have pressured domestic producers into replacing labor intensive manufacturing equipment with automated, sophisticated, efficient, high- technology machinery. The industry has focused on reducing costs, improving quality and developing quick turnaround and response scenarios. These forces have impacted the number and quality of the technical work force. Graduates with a background in computers and information management are making up a larger portion of the entry-level technical staff. Process engineers dedicated to improving quality and efficiency make up the rest. Most of the entry level work force has little or no exposure to textile education or training, they have to rely on experienced technologists to guide and train them. Unfortunately as the older technologists retire, they take with them valuable technical knowledge and know-how leaving the skeletal remains technically unsupported.
    [Show full text]
  • One Bath Enzymatic Desizing, Scouring and Activated Bleaching
    ABSTRACT LI, MIN. An Environmentally Benign Approach to Cotton Preparation: One Bath Enzymatic Desizing, Scouring and Activated Bleaching. (Under the direction of Dr. David Hinks and Dr. Ahmed El-Shafei). Current textile wet processing of woven cotton fabrics typically involves at least three stages: desizing, scouring and bleaching. The above sequences are often done separately, which involve high resource consumption and fiber damage, especially for conventional rapid hot bleaching and scouring. In this thesis, a novel process for desizing, bleaching and scouring using one bath is described in which an innovative bleach activator, N-[4- (triethylammoniomethyl)benzoyl]-butyrolactam chloride (TBBC) is employed to enable effective scouring and bleaching at reduced time and temperature compared to conventional cotton preparation. TBBC reacts with H2O2 to generate a peracid that is a more kinetically active oxidant than the perhydroxy anion that is the active oxidizer in conventional alkaline hydrogen peroxide bleaching. TBBC-activated bleaching is capable of bleaching at 50 °C at near neutral pH. Data show that effective preparation in terms of desizing, scouring, whiteness and fabric strength was achieved in a one-bath two-step process. While absorbency of the prepared fabric using the TBBC-based process was inferior to when conventional desizing, scouring and bleaching was employed, the energy, time and water consumption required were substantially reduced. Despite inferior wetting properties, the dyeing performance of the fabrics prepared using the novel process was satisfactory. TBBC-based prepared fabric was compared to conventional processes in both dyeing using single dyes as well as trichromatic dyeing. The results demonstrated that the fabric prepared using the TBBC-activated process can provide a base white which enables the fabric to dye to a similar shade as its conventionally prepared counterpart, although some adjustment may be required for the base white when predicting recipes in recipe formulation models.
    [Show full text]
  • Cold-Pad-Batch Bio-Pretreatment of Cotton Woven Fabrics: a Case Report on Industrial Trials
    Current Trends in Fashion Technology & Textile Engineering ISSN: 2577-2929 Case Report Curr Trends Fashion Technol Textile Eng Volume 1- Issue 5 - December 2017 Copyright © All rights are reserved by Eun Kyung Choe DOI: 10.19080/CTFTTE.2017.01.555573 Cold-Pad-Batch Bio-Pretreatment of Cotton Woven Fabrics: A Case Report on Industrial Trials Eun Kyung Choe1*, Juhea Kim1 and Sung Dong Kim2 1Textile Materials Division, Korea Institute of Industrial Technology, Korea 2Department of Organic and Nano System Engineering, Konkuk University, Korea Submission: October 20, 2017; Published: December 13, 2017 *Corresponding author: Eun Kyung Choe, Textile Materials Division, Korea Institute of Industrial Technology, 143 Hanggaul-ro, Sangrok-gu, Ansan-15588, Korea, Tel: ; Email: Abstract In spite of technologically proved bioscouring using pectinase that substitutes for conventional alkaline scouring, the batch-wise bioscouring in a single bath is sometimes not welcome to certain companies where continuous or cold-pad-batch alkaline pretreatment for cotton woven fabrics used to be done with pad steamer or pad-batch equipments because of low productivity of single batch-wise process as well as the company’s existing unique facility. To increase the applicability of enzymatic bioscouring, two industrial trials of bio-pretreatment by cold-pad- batch method were carried out in two different sites using their own pad-batch facilities. Simultaneous enzymatic desizing and scouring for cotton and cotton-blend woven fabrics were carried out using amylase of low-temperature type and alkaline pectinase with 100% cotton woven fabric of 200 yard length and cotton/nylon/polyurethane woven fabric of 1000 yard length by the cold-pad-batch method.
    [Show full text]
  • Biovision in Textile Wet Processing Industry- Technological Challenges
    Volume 7, Issue 1, Spring 2011 Biovision in Textile Wet Processing Industry- Technological Challenges C. Vigneswaranb, N. Anbumania and M. Ananthasubramanianc aDepartment of Textile Technology, bDepartment of Fashion Technology and cDepartment of Biotechnology PSG College of Technology Coimbatore – 641 004, India ABSTRACT Environmental consciousness is one of the major concerns for textile wet processing industry as the industry contributes much to industrial pollution problems facing the country. Such pollutants as such as lime, sodium sulfide, salt, solvents, synthetic pigments come mainly from desizing, scouring, bleaching and dyeing processes in textile wet processing. In order to overcome the hazards caused by the chemical effluents, use of enzymes as a viable alternative has been resorted to in preparatory dyeing operations such as desizing, scouring, and bleaching treatments. This review focuses on the use of microbial enzymes as an alternate technology to the conventional methods, and highlights the importance of these enzymes in minimizing the pollution load. Environmental pollution has been a major irritant to industrial development. Also in this paper we have discussed the advantages and limitations of bioprocessing techniques in the various textile wet processing such as desizing, scouring, bleaching, biopolishing, bio-singeing and bio-decoloration in the dyeing effluents for cellulosic and non-cellulosic materials. Keywords: enzymes, dyeing, wet processing, environmental pollution 1. INTRODUCTION also necessary to get optimum results. In the conventional textile wet Chemical and chemical-based industries are processing, the grey fabric has to undergo a the prime targets of the environmentalists series of chemical treatments before it turns for their crusade against pollution, and into a finished fabric.
    [Show full text]
  • LIST of LABORATORY TASKS 1. Desizing of Cotton Fabric 2. Scouring of Cotton Fabric 3
    LIST OF LABORATORY TASKS 1. Desizing of cotton fabric 2. Scouring of cotton fabric 3. Bleaching of cotton fabric 4. Combined pretreatment process of cotton fabric 5. Pretreatment using different preparatory finishing machines 6. Pretreatment process for yarns 7. Mercerization of cotton 8. Preparation of wool 9. Degumming of silk 10. Preparation of polyester and polyester/cotton blends GENERAL PROCEDURE OF LABORATORY WORK The task for every laboratory study includes the objective, the main data (description of instruments and test methods), the assignment for work, and instructions for preparation of work and on the report. Prior to starting work a student must go through the laboratory manual and the recommended literature to acquaint him/her with the materials concerning the objective of the work. The preparedness of the student for carrying out the work is checked by the instructor or with technical means. After completing a laboratory work, the students make a report in the order indicated by "format for laboratory report writing ", return the instrument and tools to the laboratory assistant and put their work places in order. In each case depending on the instruments available and the time allotted, an individual student or group of students does a laboratory work. To save time, in consultation with the instructor, the number and duration of measurements may be reduced as against the requirements of standards. SAFETY INSTRUCTIONS Use the equipment in the laboratory carefully and always leave it clean for the next student. Always report equipment problems immediately. Failure to do this may delay your progress or that of another student.
    [Show full text]