DOCSLIB.ORG

TRINITY 48” 8-DRAWER ROLLING WORKBENCH W/ COMBO LOCK Model # TLSPSB-4803 PARTS LIST

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
TRINITY 48” 8-DRAWER ROLLING WORKBENCH W/ COMBO LOCK Model # TLSPSB-4803 PARTS LIST Everything in its place.® OWNER’S MANUAL TRINITY 48” 8-DRAWER ROLLING WORKBENCH w/ COMBO LOCK Model # TLSPSB-4803 PARTS LIST Your TRINITY 48“ Rolling Workbench should include the following parts. Please inspect box contents to ensure you have received all components. If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY Customer Service: 800.985.5506 or [email protected]. Parts can also be requested online at www.trinityii.com (Help & More, Contact Us). You will need 10mm wrench (for handles) and 14mm wrench (for casters) for assembly (not included). Parts box and keys are located in the BOTTOM drawer. A B C WORKBENCH (1) SIDE HANDLE (2) HANDLE BOLT (8) M6 D E F WASHER (8) LOCKING NON-LOCKING CASTER (2) CASTER (2) G H I CASTER BOLT (16) LINER (8) KEY (1) M10 1 © 2017 TRINITY - 800.985.5506 ASSEMBLY INSTRUCTIONS STEP 1 Position SIDE HANDLE (B) over pre-installed nuts on the side of WORKBENCH (A). Insert HANDLE A (1) B (2) C (8) D (8) 10mm BOLTS (C) through the WASHERS (D) first, then the holes on SIDE HANDLE (B). Use a 10mm wrench to tighten HANDLE BOLTS (C) to WORKBENCH (A). Repeat these instructions to install the other SIDE HANDLE (B). STEP 2 Carefully lay WORKBENCH (A) on its backside. Position LOCKING CASTERS (E) on the same side of the E (2) F (2) G (16) 14mm WORKBENCH (A) and align holes to pre-installed nuts on the underside of WORKBENCH (A). Use a 14mm socket wrench to tighten CASTER BOLTS (G) to WORKBENCH (A). Repeat above step to install the NON-LOCKING CASTERS (F) on the other side of the WORKBENCH (A). Notes: * For ease of use, place LOCKING CASTERS (E) on the side you will regularly push or pull. ** If you plan to push the Workbench against a wall, place LOCKING CASTERS (E) on the front long side for ease of access. © 2017 TRINITY - 800.985.5506 2 ASSEMBLY INSTRUCTIONS STEP 3 Place the LINERS (H) inside each drawer. H (8) USAGE INSTRUCTIONS COMBINATION LOCK The factory preset combination is 0-0-0-0, even though the Dials may appear with other numbers. Locked Dials Position Knob Reset Position Unlocked Alignment Line Position Before locking the unit, make sure all drawers are fully pushed in and closed. To lock the unit, turn the knob to line up with the red dot and then turn the dials so that what is displayed is no longer the 4-digit combination. Note: If you have difficulty locking the unit, turn the knob towards the Unlocked Position (green dot) and then slowly turn it counter-clockwise to line up with the Locked Position (red dot). Then turn dials to lock it. 3 © 2017 TRINITY - 800.985.5506 USAGE INSTRUCTIONS SET NEW COMBINATION 1. Slowly turn the Knob 2. Slowly turn the Knob 3. Set your own 4. Slowly turn the Knob to the Unlocked clockwise 90 degrees to desired 4-digit counter-clockwise 90 Position (green dot), the Reset Position combination. degrees back to the leaving the Dials at the (white triangle). (Fig. C) Unlocked Position (green preset (Fig. B) dot). Your combination combination 0-0-0-0. lock is now set with the (Fig. A) new combination. (Fig. D) Fig. A Fig. B Fig. C Fig. D FORGOT YOUR COMBINATION 1. The KEY (I) may be used at 2. Gently rotate each Dial until 3. Turn the Master Key counter- any time to unlock the it stops or until you hear a clockwise 90 degrees to the Locked workbench. discernible “click”. Position (red dot) (Fig. G), then (Fig. F) remove the key. Insert and turn the KEY (I) clockwise 90 degrees to the Note: You can now keep using the Unlocked Position (green Hold the KEY (I) firmly while you retrieved 4-digit combination or dot). turn Dials to retrieve your 4-digit reset the combination by following (Fig. E) combination the instructions above. Fig. E Fig. F Fig. G NOTE: Always keep your combination a secret and the key in a safe and accessible place other than the workbench. © 2017 TRINITY - 800.985.5506 4 USAGE INSTRUCTIONS DRAWER REMOVAL Pull the drawer out so that it is almost fully extended. On the RIGHT side, push the black release lever DOWN. On the LEFT side, pull the black release lever UP. While holding the levers as instructed, pull the drawer forward until released from the slides attached to the Workbench (“Workbench Slides”). Note: The slides attached to the drawer (“Drawer Slides”) are an integral part of the drawer and must be removed along with the drawer itself. DRAWER REPLACEMENT To replace the drawer, pull the slides out completely. Insert the brackets on each side of the Drawer Slides into the corresponding slots on the Workbench Slides, making sure they are properly positioned. Once the brackets are inserted into the slots, completely close the drawer to set all slides in their proper positions. 5 © 2017 TRINITY - 800.985.5506 SERVICE PARTS LIST – TLSPSB-4803 TRINITY Customer Service provides the following replacement parts: Part Number Description Part Number Description 1) AMA-05-019-1400 14” Drawer Handle 12) XBK-22-001-1416 14” Drawer Liner 2) XBK-23-007-2512 End Cap 13) XBK-22-001-2616 26” Drawer Liner 3) ZSV-01-001-0612 Handle Bolt 14) XBK-22-001-4316 43” Drawer Liner 4) ZSV-01-007-0612 Handle Washer 15) ZSV-99-003-5020 Non-locking Caster 5) PSB-05-009-1500 Side Handle 16) PSB-07-007-4403 44” Small Drawer 6) PSB-07-007-1506 15” Drawer 17) AMA-05-019-4300 43” Drawer Handle 7) ZSV-12-010-1575 Slide (workbench side) 18) XXX-10-002-0XXX Key 8) ZSV-12-009-1575 Slide (drawer side) 19) XBK-11-004-0XXX Lock 9) PSB-07-007-4409 44” Large Drawer 20) PSB-07-007-2703 27” Drawer 10) ZSV-01-001-1020 Caster Bolt 21) AMA-05-019-2600 26” Drawer Handle 11) ZSV-99-004-5020 Locking Caster 22) LNA-06-009-4819 Wood Top 22 1 21 2 20 3 19 4 18 5 17 6 16 7 15 8 14 9 13 10 12 11 © 2017 TRINITY - 800.985.5506 6 WARNINGS 1. Read and understand all instructions. Failure to follow all instructions may result in injury and/or damage. 2. The warnings, cautions, and instructions discussed in this manual cannot cover all possible conditions or situations that may occur. The user must always be aware of their environment and ensure that they use the product in a safe and responsible manner. 3. Do NOT modify the product in any way. Unauthorized modification may impair the function and/or safety of the product, and may affect the life of the product. 4. Check for damaged parts. Before using this product, carefully check that all parts are in good condition, and that the product will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace damaged or worn parts, and never use this product with a damaged part. 5. Do NOT overload the product. Weight capacity per drawer 75 lb Total weight capacity of tool chest 1800 lb 6. Lock the casters when leaving workbench in stationary position. 7. Lock the drawers before moving the workbench. 8. Do NOT open more than one drawer at a time. Tipping can occur. 9. Do NOT step on open drawers. 10. Do NOT let children play near workbench. CARE AND MAINTENANCE • Avoid harsh, abrasive cleaners, and other corrosive chemicals. • Do not use scouring pad for cleaning. • Keep dry and avoid damp environments. 7 © 2017 TRINITY - 800.985.5506 PRODUCT REGISTRATION Thank you for purchasing a TRINITY 48” Rolling Workbench. In order to register your product and receive streamlined customer service, please fill out the following Product Registration Form and (1) fax the form to 310.347.4134 (2) complete the Product Registration Form online at www.trinityii.com or (3) scan and email the form to [email protected]. Include a copy of your original receipt with your submission. First Name: Last Name: Address: City: State: Zip Code: Email Address: Phone: Product Model #: TLSPSB-4803 Purchase Date: / / Location of Purchase: Please rate the importance of each feature (1=least important; 10=most important) Quality Price Size/Capacity Appearance Other How did you hear about our product? Magazine Ad Catalog Salesperson Word of Mouth Internet Store Display Other Marital Status: Single Married Household Income: Below $50,000 $50,000-$150,000 $150,000+ Education: High School College Graduate School Primary Residence: Own Rent Comments/Suggestions: © 2017 TRINITY - 800.985.5506 8 9 © 2017 TRINITY - 800.985.5506 1 YEAR LIMITED WARRANTY TRINITY 48” ROLLING WORKBENCH Model # TLSPSB-4803 Trinity International Industries (“Trinity”) warrants to the original consumer purchaser (“Purchaser”) of the TRINITY 48” Rolling Workbench (“Product”) that each Product shall be free from defects in workmanship and materials for a period of 1 year from the date of original purchase. Trinity’s obligation under this warranty shall be limited to repair or replacement of, or adequate compensation for the Product which shall not be greater than the amount of the purchase price of the Product, at the option of Trinity, during the warranty period. All replaced parts and Products become the property of Trinity and must be returned to Trinity. This warranty excludes normal wear and tear of the Product and its parts or components, and damage arising from any of the following: negligent use or misuse of the Product, use contrary to this User’s Manual, or alteration by any one other than Trinity.
Load more

Recommended publications
  • Master Tool Catalog
    ® • DROP CEILING INSTALLATION • MASTER TOOL CATALOG quality brands of Q.E.P. Co., Inc., founded in 1979, is a world class, worldwide provider of innovative, quality and value-driven flooring and industrial solutions. As a leading worldwide manufacturer, marketer and distributor, QEP delivers a comprehensive line of hardwood and engineered wood flooring, flooring installation tools, adhesives and flooring related products targeted for the PROFESSIONAL INSTALLER as well as the DO-IT-YOURSELFER. In addition the company provides industrial tools with cutting edge technology to all of the industrial trades. The Company continues to build its reputation for offering its customers the most comprehensive flooring installation product line and wood flooring available from one company. The company markets over 7,000 products under various brand names that are well respected in their market niches. Brand names include QEP®, ROBERTS®, Capitol®, Harris Wood®, Faus Floors®, Homelux®, TileRite®, Nupla®, HISCO®, Ludell®, Vitrex®, Plasplugs®, PRCI®, Porta-Nails®, Tomecanic®, Bénètiere® and Elastiment®. Strategically located around the world, QEP currently has distribution and manufacturing capabilities located throughout the United States, Canada, Australia, New Zealand, United Kingdom, France and China. QEP continually enhances its market leadership positions through selective acquisitions that extend its geographic reach, add proprietary product lines and broaden distribution capabilities, enabling the Company to capitalize on cross-selling opportunities.
    [Show full text]
  • 05/29/18 Tools & Home Improvement Auction
    09/27/21 12:18:09 05/29/18 Tools & Home Improvement Auction Auction Opens: Wed, May 23 3:30pm PT Auction Closes: Tue, May 29 5:30pm PT Lot Title Lot Title 0001 Husky 25 Gallon Mobile Toolbox 0029 Wiss Multi-Purpose Wire Cutters Model 0002 Husky 37" 50 Gallon Mobile Toolbox PWC9W 0003 2-Pack Window Insulation Shrink Kit 0030 Wiss Spring Assisted Folding Pocket Knife 0004 2-Pack Window Insulation Shrink Kit 0031 Wiss Quick Change Folding Utility Knife 0005 Frost King 9-Pack Window Insulation Shrink 0032 Wiss Auto Retracting Safety Utility Knife Kit 0033 Crescent Permabond 20oz. Rip Claw Hammer 0006 Bosch Self Leveling 30 ft Cross Line Laser 0034 Crescent 8" Pass Through Adjustable Wrench 0007 (2) Lengths of Frost King Door & Weather Seal Set 0008 (2) Lengths of Frost King Weather Stripping 0035 Crescent 7pc. SAE+MM Combo Nut Driver Socket Set 0009 (2) 10 ft Rubber Foam Self Stick Weather Seal 0036 Husky 6pc. Diamond Tip Magnetic Screwdriver 0010 Zircon HD25 Stud Sensor Set 0011 Zircon HD70 Stud Sensor 0037 Husky Gravity Feed HVLP Spray Gun 0012 Stanley Dual Melt Glue Gun GR25 0038 Husky High-Low Torque 1/2" Impact Wrench 0013 Stanley 10" Medium Duty Riveter Model MR33 0039 Husky Digital Sliding T-Bevel 0014 Ryobi Smart Works Moisture Meter for 0040 Husky 46pc. Stubby Wrench & Socket Set Smartphone 0041 Husky 23pc. Precision Screwdriver Set 0015 Stanley Powerlock 16 ft & Fatmax 25 ft Tape Measures 0042 Husky 2pc. Quad Drive Ratcheting Wrench Set 0016 (2) Stanley Utility Knives w/10 Spare Blades 0043 Husky 2" O.D.
    [Show full text]
  • 1. Hand Tools 3. Related Tools 4. Chisels 5. Hammer 6. Saw Terminology 7. Pliers Introduction
    1 1. Hand Tools 2. Types 2.1 Hand tools 2.2 Hammer Drill 2.3 Rotary hammer drill 2.4 Cordless drills 2.5 Drill press 2.6 Geared head drill 2.7 Radial arm drill 2.8 Mill drill 3. Related tools 4. Chisels 4.1. Types 4.1.1 Woodworking chisels 4.1.1.1 Lathe tools 4.2 Metalworking chisels 4.2.1 Cold chisel 4.2.2 Hardy chisel 4.3 Stone chisels 4.4 Masonry chisels 4.4.1 Joint chisel 5. Hammer 5.1 Basic design and variations 5.2 The physics of hammering 5.2.1 Hammer as a force amplifier 5.2.2 Effect of the head's mass 5.2.3 Effect of the handle 5.3 War hammers 5.4 Symbolic hammers 6. Saw terminology 6.1 Types of saws 6.1.1 Hand saws 6.1.2. Back saws 6.1.3 Mechanically powered saws 6.1.4. Circular blade saws 6.1.5. Reciprocating blade saws 6.1.6..Continuous band 6.2. Types of saw blades and the cuts they make 6.3. Materials used for saws 7. Pliers Introduction 7.1. Design 7.2.Common types 7.2.1 Gripping pliers (used to improve grip) 7.2 2.Cutting pliers (used to sever or pinch off) 2 7.2.3 Crimping pliers 7.2.4 Rotational pliers 8. Common wrenches / spanners 8.1 Other general wrenches / spanners 8.2. Spe cialized wrenches / spanners 8.3. Spanners in popular culture 9. Hacksaw, surface plate, surface gauge, , vee-block, files 10.
    [Show full text]
  • STEEL WORKBENCH 1650Mm
    INSTRUCTIONS FOR: STEEL WORKBENCH 1650mm MODEL No: AP165WB Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to instruction manual 1. SAFETY 1.1 GENERAL SAFETY WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this workbench. WARNING! Use caution when handling and assembling the metal components. The metal may have sharp edges or corners, the use of protective gloves is recommended. Locate workbench in a suitable working area. Keep the work area clean, uncluttered and ensure there is adequate lighting. Keep the workbench clean and tidy in accordance with good workshop practice. Keep children and unauthorised persons away from the working area. DO NOT climb, step or stand on the workbench. DO NOT use the workbench for any purpose other than that for which it is designed. DO NOT use in damp work areas. WARNING! The warnings, cautions and instructions referred to in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
    [Show full text]
  • HAND TOOLS Hablamos Español
    1-877-AZTool1 (1-877-298-6651) HAND TOOLS Hablamos Español Wrench Sets Drive Bits Master Hex Bit Set ST EE L SKU 094663 25952 4999 1/4” Drive: ST EE L 1/8”, 5/32”, 3/16” and 7/32” 3/8” Drive: 1/4”, 9/32”, 5/16” and 11/32” 35-Piece Master Torx Bit Set 44-Piece Master Torx and Hex Bit Set 1/2” Drive: 3/8”, 1/2”, 9/16”, 3/4” and 5/8” SKU 466622 SKU 311698 99 99 1/4” Drive: 25951 49 25950 46 2.5, 3, 4 and 5 mm • Star: T8, T10, T15, T20, T25, T27, T30, T40, T45, Hex:, 2 2.5, 3, 4, 5, 6, 7, 8, 10; 1/8”, 5/32”, 3/16”, 7/32”, 1/4”, 5/16” and 3/8” 3/8” Drive: ST EE L T47, T50, T55 and T60 Star: T10, T15, T20, T25, T27, T30, T40, T45, T47, T50, T55 and T60 6, 7, 8 and 9 mm 16-Piece • Tamper Proof Star: T7, T8, T9, T10, T15, T20, T25, Phillips: #1, #2 and #3 1/2” Drive: 10, 12, 14, 17 and 19 mm Combo Wrench Set - SAE T30, T40, T45, T50 and T55 Slotted: 3/16”, 1/4” and 5/16” • Female Star: E4, E5, E6, E7, E8, E10, E12, E14, SKU 531642 99 E16 and E18 Bits: T7H, T8H, T9H, T10H, T15H, T20H, T25H, T27H and T30H 17329 49 11-Piece Tamper Proof Torx Plus Bit Socket Set • Sizes Include: 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8 and 1-1/4" SKU 255725 • Durable Nylon Storage Pouch 13-Piece 1/4” Drive 22973 Tamper-Resistant Star Security Bits • Raised Panel Design SKU 447157 99 99 24293 29 59 • Sizes: T7-T50 • Set Includes: (1/4” Drive) 8-TPT, 10-TPT, 15-TPT, 20-TPT and 25-TPT, (3/8” Drive) 27-TPT, 30-TPT, 40-TPT, 45-TPT, 50-TPT and 55-TPT Stubby Star Drive Sets Tamper Proof 13-Piece 1/4” Drive • 3/4" Overall Length Designed
    [Show full text]
  • Punches / Chisels the Anvil End on Heads of Snap-On® Punches and Chisels Are Machined to a Modified Parabolic Curve
    Punches / Chisels The anvil end on heads of Snap-on® punches and chisels are machined to a modified parabolic curve. This design directs the striking force to the center of the tool head to allow slow metal displacement. The parabolic curve controls mushrooming to reduce chipping and splitting. Heads should be re-dressed to their original shape with hand files as necessary. The tough steel alloy is machined and differentially heat treated for optimum performance. The hardness of the striking head is reduced to help toughness and add qualities that result in a slower mushrooming of the striking surface. Stock Hex Point/ Length Stock Hex Point/ Length No. Size, in. Edge, in. in. No. Size, in. Edge, in. in. Punch and Chisel Accessories PPC808A 1/4 1/4 5 Flat Chisels PPC1A — — 2 5/8 PPC812B 5/16 3/8 5 1/2 Chisel Gauge PPC816B 7/16 1/2 6 PPC5A — — 6 15/16 PPC820B 1/2 5/8 6 1/2 PPC1A PPC5A Punch/Chisel Holder PPC824B 5/8 3/4 7 1/4 11 7 Center Punches PPC3A 5/16 1/8 5 PPC828B /16 /8 8 PPC832B 7/8 1 9 PPC4A 7/16 3/16 6 BPPC1878 7/8 1 9 PPC6B 5/8 5/16 7 PPC820LB 1/2 5/8 16 Long Flat Chisels PPC714B 9/16 5/32 14 Pin Punches PPC103A 9/32 3/32 4 7/32 PPC104A 5/16 1/8 4 3/4 PPC105A 3/8 5/32 5 3 3 1 PPC106A /8 /16 5 /4 PPC12B 3/8 5/16 6 Half Round Nose Cape PPC107A 3/8 7/32 5 1/4 PPC108A 7/16 1/4 5 3/4 Chisels PPC110A 1/2 5/16 5 1/4 PPC112 9/16 3/8 5 1/4 Starter Punches PPC203A 5/16 3/32 5 1/2 3 1 3 PPC204A /8 /8 5 /4 PPC13B 5/16 1/4 5 5/8 3 5 Cape Chisels PPC205A /8 /32 6 PPC14B 3/8 5/16 6 PPC206A 7/16 3/16 6 1/4 PPC208A 1/2 1/4 6 3/4 PPC210A 9/16 5/16 7 1/4 PPC15B 7/16 7/32 6 Diamond Point Chisels PPC19B 3/8 1/8 5 3/4 PPC250AK PPC250AK Punch and Chisel Set Includes the following 25 pcs.
    [Show full text]
  • Torque Wrench Operator’S Manual
    Model # 24340 ® TORQUE WRENCH OPERATOR’S MANUAL STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE !? NEED HELP? 888-648-3371 [email protected] Please read and understand entire manual, including all safety information, before using torque wrench. This tool is a precision measuring instrument. Handle with care and store properly. Do not attempt to increase leverage of this wrench with any other device. Failure to follow all instructions could result in damage to torque wrench, property damage, or injury. • At low torque settings, pull wrench slowly to observe click. • Wrench is shipped ready to use, calibrated and tested to an accuracy of +/- 4%. To maintain this accuracy, it is important that wrench is stored at lowest torque setting, 25 .-lb (33.9 Nm). This setting relieves extra tension on the internal spring, eliminating fatigue that can adversely affect accuracy. SETTING TORQUE READING Fig. A HANDLE BODY KNURLED HANDLE This is a dual-range torque wrench marked with MAIN SCALE foot pounds (.-lb.) and Newton meters (Nm) on opposite sides of handle. The torque scale is marked on the handle body with more precise subdivisions on the knurled MICROMETER SCALE LOCK NUT handle (Fig. A). In these instructions the handle body scale will be referred to as the “main STORE AT scale” and the knurled handle scale will be 25 FT.-LB. referred to as the “micrometer scale”. Fig. B Fig. C STORE AT FT.-LB. Tighten/adjust lock nut and knurled 25 FT.-LB. 250 handle by hand only. FT.-LB. 200 225 150 175 Foot Pounds (Example reading: 120 .-lb.) 250 100 125 200 225 50 75 1.
    [Show full text]
  • IEI Versatile Socket Wrench and Offset Ratchet Screwdriver Sets and Kits
    versatile socket wrench and offset ratchet screwdriver IEI sets and kits 14-piece, 1/4" Square Drive Socket Wrench set -No.1001 This versati le set of precision made tools speeds the repair and adjustment of radio, TV, appliance, business machine, commun i­ cation, aviation, automotive, other electronic and industrial equipment and instrumentation. Six-point sockets are provided to f it most normally encountered hex fastener sizes. Ten-po int sockets (Nos. 1308 and 1310) are dual purpose and provide fu ll bearing and snug fit on both square and hex nuts, bolts, drain and pipe plugs. Sockets are hot forged from A .1 .S.1. 4140 alloy steel, a superior metal that is tougher and stronger than ca rbon steels. Heat treat­ ment in a controlled atmosphere furnace develops hard, long­ wearing surfaces. Of lightweight but rugged, streamlined design with straight sidewall s, these sockets feature chamfered drive ends for easy insertion of ratchets and attachments. The reversible ratchet mechanism is fully enclosed to keep out dirt and grit. Close fits, large bearing areas, and controlled atmos­ phere heat treatment resu It in long life without play. The reversing shift is easily operated by a flick of the thumb. A short ( 1/4 " minimum) handle swing and small round head permit work in tight quarters. The unique spinner/extension has a 1/4" square drive at the shaft end and a 1/4" drive socket insert in the end of the black (UL) plastic handle. It ca n be used with sockets as a regular nut­ driver or as a ratchet extension in numerous ways as shown in the accompanying chart.
    [Show full text]
  • Polar® Socket Wrench Sets and Tool Sets
    POLAR® SOCKET WRENCH SETS AND TOOL SETS 5191 A 1/4” AND 3/8” METRIC TOOL SET 98 ITEM NO. 5191-1098 TOOLS ■ Socket wrench set in watertight plastic case with short and long 6-point sockets, bits, combination wrenches, screwdrivers, adjustable wrench, pliers, hammer and accessories. ■ The set is supplied with reversible ratchets with locking system. ■ 98 tools. 420 MM 80 MM 310 MM 6,0 KG 5704196 000664 1 1/4” 3/8” 1/4” CONTENT: QTY. DESCRIPTION SIZE QTY. DESCRIPTION SIZE 12 6-point sockets 5014 1/4” 4 - 4.5 - 5 - 5.5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 mm 5 Bits for slotted head screws 4514 1/4” 3.5 - 4.5 - 5.5 - 6.5 - 8 mm 10 Long 6-point sockets 5014 1/4” L 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 mm 3 Bits for Phillips® screws 4514 1/4” PH 1 - 2 - 3 12 6-point sockets 5038 3/8” 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 22 mm 3 Bits for Pozidriv® screws 4514 1/4” PZ 1 - 2 - 3 2 Spark plug sockets 5038 3/8” SP 18 - 21 mm 10 Bits for Tamper Resistant® Torx® screws 4514 1/4” STX T7 - T8 - T9 - T10 - T15 - T20 - T25 - T27 - T30 - T40 1 Ratchet, 60 teeth 5314 A 1/4” 7 Bits for hex head screws 4514 1/4” H 2 - 3 - 4 - 5 - 6 - 7 - 8 mm 1 Ratchet, 72 teeth 5338 3/8” 2 Bits for square head screws 4514 1/4” SQ 1 - 2 2 Extensions 5214 1/4” EX 50 - 100 mm 1 Screwdriver for slotted 2 Extensions 5238 3/8” EX 150 - 250 mm head screws 4000 5,5 x 125 mm 1 Sliding T-handle 5414 1/4” TH 1 Screwdriver for Phillips® screws 4010 PH 2 ® 1 Universal joint 5814 1/4” U 1 Screwdriver for Pozidriv screws 4020 PZ 2 1 Universal joint 5838 3/8” U 13 Combination wrenches 2000 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 mm 1 Plastic handle driver 5514 1/4” HD 1 Adjustable wrench 2605 150 mm / 8” 1 Screwdriver bit socket 4714 1/4” x 1/4” 1 Combination plier 3001 180 mm 1 Waterpump plier 3020 250 mm 1 Quick-Release screwdriver bit socket 4714 1/4” QR 1 Engineers hammer 8030 300 g 17 POLAR® SOCKET WRENCH SETS AND TOOL SETS 5191 B 1/4” AND 1/2” METRIC TOOL SET 98 ITEM NO.
    [Show full text]
  • 495 T-Handle Socket Wrench Screwdrivers, 10 X 230 Mm
    495 T-handle socket wrench screwdrivers, 10 x 230 mm Series 400 T-Handle EAN: 4013288208415 Size: 280x98x22 mm Part number: 05023387001 Weight: 165 g Article number: 495 Country of origin: CZ Customs tariff 82054000 number: T-handle screwdriver for the transmission of particularly high tightening and loosening moments Ergonomic 2-component handle with finger handle recesses and pleasant surface feel for very high power transmission and fatigue-free working. With handle markings by profile and size. Special surface treatment for high corrosion protection and optimum fitting accuracy T-handle screwdriver: The ideal handle shape to allow high torque transmission in difficult tightening and loosening situations. The ergonomic shape of the handle fills the palm of the hand well, the fingers lie safely in the soft rounded handle recesses. The whole hand makes contact with the handle and friction losses between the hand and the handle are avoided. Special surface treatment of the blades for high corrosion protection and an optimum fit in the screw head. Web link https://products.wera.de/en/screwdrivers_series_400_t-handle_495.html Wera - 495 Wera Werkzeuge GmbH 05023387001 - 4013288208415 Korzerter Straße 21-25 D-42349 Wuppertal Tel: +49 (0)2 02 / 40 45-0 27.02.2020 - 1 / 2 E-Mail: [email protected] 495 T-handle socket wrench screwdrivers, 10 x 230 mm Series 400 T-Handle Ergonomic 2-component T- High torque transfer Corrosion protection and fitting “Take it easy” Tool Finder handle accuracy The ergonomically shaped By using the blade as an extension Due to the special surface Screwdrivers with “Take it easy" 2-component T-handle with finger of your lower arm you can transfer treatment, the blades receive a tool finder: colour coding recesses and pleasant surface particularly high torque.
    [Show full text]
  • Hex Key Wrench
    INDEX GENERAL TOOLS G01 Cutters G02 Pliers / Grip pliers G03 Riveters Wrench / Ratchet wrench / Hook & Pin G04 wrench G05 Engineering G06 Torque tools G07 Hex key wrench / Bicycle repair tools G08 Professional bits / Bit set Bit driver / Screwdriver set / Precision G09 screwdriver G10 Impact driver / Impact driver bits G11 Ratchet handle / Bit set / Socket set G12 Impact socket & Accessories G13 Hand sanding block G14 Packing tools Cutters BC3-12 MBC-81MBS BOLT CUTTER, GENERAL TYPE MINI BOLT CUTTER ● Professional quality. Blade material... SCM steel ● Size... 8” (200 mm) Item no. Size Item no. Size ● Blade... Stainless steel, HRC: 50°±2°, Mirror polish. ----------------------------------------------------------------------------------- ● Alum. Handle with PVC grip ● BC3-12 12" ( 300 mm ) ● BC3-24 24" ( 600 mm ) ● Cutting capacity... ● BC3-14 14" ( 350 mm ) ● BC3-30 30" ( 750 mm ) HRC 15°... Dia. 3 mm. HRC 35°... Dia. 1.5 mm ● BC3-18 18" ( 450 mm ) ● BC3-36 36" ( 900 mm ) BC4-12 MBC-81MOS BOLT CUTTER , JAPAN TYPE MINI BOLT CUTTER ● Professional quality. Blade material... SCM steel ● Size... 8” (200 mm), Bent type Item no. Size Item no. Size ● Blade... Stainless steel, HRC 50°±2°, Mirror polish. ----------------------------------------------------------------------------------- ● Alum. Handle with PVC grip. ● BC4-12 12" ( 300 mm ) ● BC4-24 24" ( 600 mm ) ● Cutting capacity... ● BC4-14 14" ( 350 mm ) ● BC4-30 30" ( 750 mm ) HRC 15°... Dia. 3 mm. HRC 35°... Dia. 1.5 mm ● BC4-18 18" ( 450 mm ) ● BC4-36 36" ( 900 mm ) BC2-12 MBC-8MBA BOLT CUTTER MINI BOLT CUTTER ● Blade material... CR-V steel ● Size... 8” (200 mm) Item no. Size Item no. Size ● Blade..
    [Show full text]
  • AB 0100 EN Servicing SAMSON Products Tightening Torques · Lubricants · Tools
    AB 0100 EN Servicing SAMSON Products Tightening Torques · Lubricants · Tools Electric and Pneumatic Control Valves SAMSON AKTIENGESELLSCHAFT · Weismüllerstraße 3 · 60314 Frankfurt am Main, Germany Edition February 2021 Phone: +49 69 4009-0 · Fax: +49 69 4009-1507 · [email protected] · www.samsongroup.com Contents Information for All Valve Series and Types 1 Contact data of SAMSON's After-sales Service ....................................................................................................1 2 Safety instructions and measures ........................................................................................................................1 3 Special tools for tightening torques .....................................................................................................................1 3.1 Torque wrench ....................................................................................................................................................1 3.2 Torque multiplier .................................................................................................................................................2 3.3 Adapter .............................................................................................................................................................2 3.4 Pneumatic adapter ..............................................................................................................................................3 3.5 Hydraulic power tool ...........................................................................................................................................3
    [Show full text]