DOCSLIB.ORG

Performance Exhaust

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Performance Exhaust Weatherly Index 170 No. CB1016 Issue 2 DISTURBING THE PEACE, SINCE 1968 PERFORMANCE EXHAUST TABLE OF CONTENTS Glasspacks . 2-4 X Pipes . 19 Header Mufflers . 4 Y-Connectors . 19 M-80 Mufflers . 5 U-Bend Pipes . 19 Salute Mufflers . 6-9 Elbows . 20-21 Vortex Mufflers . 10-11 Clamps . 22 Extreme Mufflers . 12 Header Adapters & Gaskets . 23 Pro Mufflers . 13-15 Hangers . 23 Turbo Mufflers . 16-17 Tips . 24-29 Hot Rod Mufflers . 18 Flex Couplings . 29 Race Mufflers . 18 TECH LINE: 1-800-277-2787 1 GLASSPACK SPECIFICATIONS HIGH FREQUENCY SOUND EXHAUST FLOW • Straight-thru design • 100% welded construction • Cherry Bomb Red powder coat • Reversible design for maximum installation flexibility • Compact round body size • The original glasspack since 1968 GLASSPACK 3½" BODY Angled Necks 21½" 23" 28" 14" 18" 22" 2" 2" 2" 2" 2" 2" 87048CB Full Offset 87097CB Full Offset 87016CB Medium Offset 26" 25½" 30" 18" 18" 22" 2¼" 2¼" 2½" 2¼" 2½" 2¼" 87046CB Full Offset 87087CB Medium Offset 87052CB Medium Offset Full Offset - (Used for OFFSET / OFFSET Applications) Medium Offset - (Used for OFFSET / CENTER Applications) All neck sizes are inside diameter unless otherwise noted. 2 glasspack SPECIFICATIONS 3½" BODY Straight Necks 12" 22½" 26½" 8" 18" 22" 2" 2" 2" 2" 2" 2" 87520CB 87507CB 87502CB 30½" 12" 23" 26" 8" 18" 2¼" 2¼" 2" 2" 2¼" 2¼" 87512CB 87521CB 87510CB 27½" 30½" 12" 22" 26" 8" 2¼" 2¼" 2¼" 2¼" 2½" 2½" 87505CB 87515CB 87522CB 23" 30" 18" 26" 2½" 2½" 2½" 2½" 87529CB 87516CB 4" BODY Straight Necks 12" 16" 20" 8" 12" 16" 3" 3" 3" 3" 3" 3" 87524CB 87525CB 87526CB 23" 27" 35" 18" 22" 30" 3" 3" 3" 3" 3" 3" 87517CB 87518CB 87519CB All neck sizes are inside diameter unless otherwise noted. TECH LINE: 1-800-277-2787 3 GLASSPACK SPECIFICATIONS 5" BODY Straight Necks 12" 12" 8" 8" 3½" 3½" 4" 4" 87527CB 87528CB 3½" BODY Header Mufflers - Gasket Included 5 23" 3 ⁄8" 27½" 3 3 ⁄8" 3 3" 2¼" 3 ⁄8" 2" 3¾" 3-Bolt 87556CB 87551CB Flange 4-Bolt Fits 3 & 4 bolt header flanges Flange 4" BODY Header Muffler - Gasket Included 36" 3 3 ⁄8" 3" SIDE PIPE 3-Bolt Flange 87553CB 4" O.D. All neck sizes are inside diameter unless otherwise noted. 4 M-80 SPECIFICATIONS HIGH FREQUENCY SOUND EXHAUST FLOW • Straight-thru design • 100% welded construction • Cherry Bomb Red powder coat • Directional Flow Through • Single Chamber M-80 5" BODY Straight Necks 19" 19" 19" 13" 13" 13" 2" 2" 2 ¼" 2 ¼" 2 ½" 2 ½" M80200 M80225 M80250 19" 19" 13" 13" 3" 3" 4" 4" M80300 M80400 All neck sizes are inside diameter unless otherwise noted. TECH LINE: 1-800-277-2787 5 SALUTE SPECIFICATIONS HIGH FREQUENCY SOUND EXHAUST FLOW • 409 stainless steel construction • 100% welded • Straight through perforated core • Stainless steel wool inner wrap with roving fiber • Reversible flow SALUTE 4" x 9" OVAL 14" BODY 20" OVERALL OFFSET/OFFSET OFFSET/CENTER 20" 20" 20" 14" 14" 14" 2 ¼" 2" 2 ¼" 2" 2 ¼" 2 ¼" SA1235 SA1224 SA1225 20" 20" 20" 14" 14" 14" 2 ½" 2 ½" 3" 2 ½" 3" 2 ½" SA1236 SA1226 SA1229 All neck sizes are inside diameter unless otherwise noted. 6 SALUTE SPECIFICATIONS 4" x 9" OVAL 14" BODY 20" OVERALL CENTER/DUALS 20" 20" 20" 14" 14" 14" 2 ¼" 2 ¼" 2 ½" 2 ¼" 2 ½" 2 ½" INLET 2 ¼" INLET 2 ¼" INLET 2 ½" SA1149 SA2157 SA2158 20" 20" 14" 14" 2 ¼" 2 ½" 3" 3" INLET 2 ¼" INLET 2 ½" SA2197 SA2198 4" x 9" OVAL 18" BODY 24" OVERALL OFFSET/OFFSET CENTER/OFFSETOFFSET/CENTER 24" 24" 24" 18" 18" 18" 2 ½" 2 ¼" 2 ½" 2 ¼" 2 ½" 2 ½" SA1266 SA1255 SA1256 24" 18" TRANSVERSE & OFFSET/ DUALS 3" 3" 24" 18" 2 ½" 2 ½" SA1259 2 ½" INLET SA2265 All neck sizes are inside diameter unless otherwise noted. TECH LINE: 1-800-277-2787 7 SALUTE SPECIFICATIONS 4" x 9" OVAL 18" BODY 24" OVERALL CENTER/DUALS 24" 24" 24" 18" 18" 18" 2 ¼" 2 ½" 2 ¼" 2 ½" 2 ½" 3" INLET 2 ¼" INLET 2 ½" INLET 2 ¼" SA2258 SA2268 SA2278 24" 24" 18" 18" 2 ½" 3" 3" 3" INLET 2 ½" INLET 3" SA2288 SA2298 5" x 11" OVAL 22" BODY 28" OVERALL DUAL/DUAL CENTER/DUAL 28" 28" 22" 22" 2 ½" 2 ½" 2 ½" 3" 2 ½" 2 ½" 2 ½" SA2568 SA2588 OFFSET/CENTER 28" 22" 3" 3" SA2589 All neck sizes are inside diameter unless otherwise noted. 8 SALUTE SPECIFICATIONS 4" ROUND 14" BODY 20" OVERALL CENTER/CENTER 20" 20" 14" 14" 2¼" 2¼" 2½" 2½" SA0445 SA0416 4" ROUND 18" BODY 24" OVERALL CENTER/CENTER 24" 24" 18" 18" 2¼" 2¼" 2½" 2½" SA0425 SA0426 7" ROUND 24" BODY 30" OVERALL CENTER/CENTER 30" 24" 4" 4" SA2772 All neck sizes are inside diameter unless otherwise noted. TECH LINE: 1-800-277-2787 9 vortex SPECIFICATIONS HIGH FREQUENCY SOUND EXHAUST FLOW • Patented flow divider design with high temp fiberglass • 100% welded construction • High temp grey finish • Reversible design for maximum installation flexibility • Standard body size • Recommended for car, truck VORTEX and SUV applications 4¼" x 10¼" OVAL 14" BODY 20½" OVERALL OFFSET/OFFSET CENTER/OFFSET 20½" 20½" 20½" 20½" 14" 14" 14" 14" 2¼" 2½" 2¼" 2½" 2¼" 2½" 2¼" 2½" 88103CB 4 ¼88100CB" x 10¼" 4 ¼88102CB" x 10¼" 4 ¼88101CB" x 10¼" 4 ¼" x 10¼" 20½" 14" 20½" 14" 3" 3" 3" 3" 4 ¼88104CB" x 10¼" 4 ¼88105CB" x 10¼" All Vortex Mufflers are Reversible Except for Cross-Flow All neck sizes are inside diameter unless otherwise noted. 10 vortex SPECIFICATIONS 4¼" x 10¼" OVAL 16" BODY 22½" OVERALL CENTER/DUAL 22½" 22½" 22½" 16" 16" 16" 2¼" 2¼" 2½" 2¼" 2½" 2½" 2¼" 2¼" 2½" 88106CB 88107CB 88108CB 4 ¼" x 10¼" 4 ¼" x 10¼" 4 ¼" x 10¼" 22½" 22½" 22½" 16" 16" 16" 2¼" 2½" 3" 3" 3" 3" 2¼" 2½" 3" 88112CB 88109CB 88110CB 4 ¼" x 10¼" 4 ¼" x 10¼" 4 ¼" x 10¼" 4¼" x 10¼" OVAL 17" BODY 23½" OVERALL DUAL/DUAL Can Be Used As an X-Pipe 23½" 23½" 17" 17" 2¼" 2½" 2½" 2½" 2¼" 2½" 2½" 2½" 88115CB 88116CB 4 ¼" x 10¼" 4 ¼" x 10¼" CROSS-FLOW 23½" 23½" 17" 17" Inlet Inlet 2½" 3" 2½" 2½" 2½" 2½" 88111CB 88117CB 4 ¼" x 10¼" 4 ¼" x 10¼" All Vortex Mufflers are Reversible Except for Cross-Flow All neck sizes are inside diameter unless otherwise noted. TECH LINE: 1-800-277-2787 11 EXTREME SPECIFICATIONS HIGH FREQUENCY SOUND EXHAUST FLOW • Short body size with unique wing plate design • 100% welded construction • Custom tuned flow design • Cherry Bomb Red powder coat • Recommended for aggressive sound EXTREME 4" x 9¾" OVAL 6" BODY 12" OVERALL OFFSET/OFFSET CENTER/CENTER 12" 12" 12" 6" 6" 6" 2½" 2½" 2½" 3" 3" INLET INLET 2½" INLET 7480CB 7426CB 7428CB CENTER/DUAL DUAL/DUAL 12" 12" 12" 6" 6" 6" 2½" 2½" 2¼" 2½" 2½" 3" 2½" 2½" INLET 2¼" INLET 2½" INLET 7425CB 7427CB 7481CB All Pro Mufflers are Directional Flow Design. All neck sizes are inside diameter unless otherwise noted. 12 extremePRO SPECIFICATIONS HIGH FREQUENCY SOUND EXHAUST FLOW • Unique wing plate design • 100% welded construction • High temp grey finish • Non-reversible custom tuned flow design • Standard body size • Recommended for car and truck applications PRO 4" x 9¾" OVAL 13" BODY 19" OVERALL CENTER/CENTER 19" 19" 19" 13" 13" 13" 2¼" 2¼" 2½" 2½" 3" 3" INLET INLET INLET 7401CB 7402CB 7403CB OFFSET/CENTER 19" 19" 19" 19" 13" 13" 13" 13" 2" 2¼" 2½" 3" 2" 2¼" 2½" 3" INLET 7404CB INLET 7405CB INLET 7406CB INLET 7407CB All Pro Mufflers are Directional Flow Design. All neck sizes are inside diameter unless otherwise noted. TECH LINE: 1-800-277-2787 13 pro SPECIFICATIONS 4" x 9¾" OVAL 13" BODY 19" OVERALL CENTER/OFFSET 19" 19" 19" 13" 13" 13" 2¼" 2½" 3" 2¼" 2½" 3" INLET INLET INLET 7409CB 7410CB 7411CB GM Trucks OFFSET/OFFSET 19" 19" 19" 13" 13" 13" 2¼" 2½" 3" 2¼" 2½" 3" INLET 7413CB INLET 7414CB INLET 7415CB CENTER/DUAL 19" 19" 13" 13" 2¼" 2½" 2½" 2½" 2¼" 2½" INLET INLET 7470CB 7419CB 19" 19" 13" 13" 2¼" 2½" 3" 3" 2¼" 2½" INLET INLET 7420CB 7421CB All Pro Mufflers are Directional Flow Design. All neck sizes are inside diameter unless otherwise noted. 14 pro SPECIFICATIONS 4" x 9¾" OVAL 16½" BODY 22½" OVERALL CENTER/OFFSET 22½" 16½" 2¼" 2¼" INLET 7456CB CENTER/DUAL 22½" 22½" 16½" 16½" 2¼" 2½" 3" 3" 2¼" 2½" INLET INLET 7465CB 7464CB OFFSET/DUAL CROSS-FLOW 22½" 22½" 16½" 16½" 2¼" 2½" INLET 2½" 2¼" 2½" 2½" INLET 7471CB 7467CB All Pro Mufflers are Directional Flow Design. All neck sizes are inside diameter unless otherwise noted. TECH LINE: 1-800-277-2787 15 turbo SPECIFICATIONS HIGH FREQUENCY SOUND EXHAUST FLOW • Reverse-flow design • Mechanically-locked construction • Reversible design for maximum installation flexibility • Standard and small body size • Recommended for car and truck applications TURBO 3¼" x 7¾" OVAL OFFSET/CENTER 16" 20" 17" 17" 11" 14" 13" 13" 2" 2" 2¼" 2½" 2" 2" 2¼" 2½" 16807CB 16810CB 16808CB 16809CB OFFSET/OFFSET 16" 20" 17" 11" 14" 13" 2" 2" 2¼" 2" 2" 2¼" 16811CB 16813CB 16812CB All Turbo Mufflers are Reversible. Turbo Mufflers are Double Wrapped. All neck sizes are inside diameter unless otherwise noted. 16 turbo SPECIFICATIONS 4¼" x 8¾" OVAL OFFSET/CENTER 18" 18" 18" 14" 14" 14" 2" 2¼" 2½" 2" 2¼" 2½" 16821CB 16822CB 16823CB OFFSET/OFFSET 18" 18" 18" 14" 14" 14" 2" 2¼" 2½" 2" 2¼" 2½" 16824CB 16825CB 16826CB 1 4 ⁄16" x 10½" OVAL OFFSET/CENTER 18" 18" 19" 14" 14" 14" 2¼" 2½" 3" 2¼" 2½" 3" 16831CB 16832CB 16833CB CENTER/DUAL DUAL/DUAL 21" 21" 24" 14" 14" 18" 2½" 2¼" 2¼" 2¼" 2¼" 3" 2¼" 2¼" 2¼" 2¼" 16834B 16835CB 16841CB All Turbo Mufflers are Reversible.
Load more

Recommended publications
  • DMF Muffler Offers a New Level of Emission Reduction for 1991-2002 Model Year Diesel-Powered Engines
    A High Efficiency Emissions Retrofit Solution with No Maintenance – The Diesel Multi-stage Filter (DMF) Muffler The patented 1 Donaldson DMF Muffler offers a new level of emission reduction for 1991-2002 model year diesel-powered engines. As a tailpipe solution, this product will reduce your diesel PM emissions up to 60%! Reduce your total vehicle emissions even more with our patented 2 combination – the DMF Muffler and Spiracle™ Crankcase Filtration System. 1 U.S. Pat. No. 7,340,888 2 U.S. Pat No. 7,278,259; 7,257,942 High Efficiency Filtration with No Maintenance .... our DMF Mufflers DO NOT require routine ash cleaning Partial Flow Through Filter Broad Engine Coverage The DMF Muffler uses a two- • Approved for four-stroke on-road diesel engine applications stage metallic filter to trap with engine horsepower ranges of 150-600 hp and reduce diesel particulate - 1991-1993 model year engines (0.25 g/bhp-hr PM or less) matter (PM). Each filter with exhaust temperatures of 230º C for 40% of the time stage consists of alternating and average exhaust temperature of 215º C or above layers of a corrugated metal and a porous sintered metal - 1994-2002 model engines (0.10 g/bhp-hr PM or less) fleece. The unique catalyst with exhaust temperatures of 210º C for 40% of time and coating reduces PM, HC and average exhaust temperature of 210º C or above CO, while minimizing NO2 • For even more emissions reduction, consider ordering a emissions (<20% increase). kit that includes the Donaldson closed crankcase filtration system - Spiracle™ and DMF Muffler.
    [Show full text]
  • Flowmaster Exhaust Systems Are Designed Vehicle Specific and Do Not Violate the Manufacturer’S Factory Warranty
    2016 MUFFLERS // SYSTEMS // HEADERS // CATALYTIC CONVERTERS // TIPS & ACCESSORIES FLOWMASTER MANUFACTURING Shown in a rare quiet moment, Flowmaster’s state-of-the-art manufacturing plant in Northern California features many self-designed tools and high-tech robotics to build the world’s most advanced mufflers. For over three decades, Flowmaster has led the way in automotive performance exhaust technology with some of the earliest product patents held by an exhaust manufacturer. As the world’s first fully welded muffler in 1983, Flowmaster raised the bar for durability and strength, while singlehandedly reinventing the performance exhaust industry. Today, we maintain that edge with constant innovation in exhaust solutions for street, race, and off-road applications. 2 WWW.FLOWMASTERMUFFLERS.COM TECHNOLOGY CAR APP 05 12 HEADERS TRUCK APP 06 34 CONVERTERS MUFFLERS 08 50 RACE PARTS Tech Support: 1-707-544-4761 www.flowmastermufflers.com 66 ACCESSORIES 72 The Exclusive Performance Exhaust Of NASCAR INFO / FAQ FIND US ON: 80 NOTE: Flowmaster’s muffler recommendations are based on OEM configurations, but are not considered direct-fit replacements. Our universal mufflers may require modification during installation. Additional muffler options may apply outside of these recommendations. Should you have any questions, call our tech line for further assistance in selecting a system or muffler. WWW.FLOWMASTERMUFFLERS.COM 3 ABOUT THE COMPANY For over 30 years, Flowmaster has been the leader in advanced exhaust technology through our extensive commitment to research and development. Early on we learned that by understanding an engine’s total operation, we could not only generate a terrific performance exhaust sound, but more importantly increase combustion efficiency and improve both performance and fuel mileage.
    [Show full text]
  • Exhaust/Emissions Systems Overview Emissions Testing
    Exhaust/Emissions Systems Overview Below is an overview of this system's operation Emissions Testing Many states require emissions tests on vehicles. This means that you drive to a facility where the test people take a sample of your emissions and run it through some analysis. The results are printed,and you pass or fail depending on the percentage of toxic emissions that turn up in your car's sample. The only way to "study" or prepare for this test is to take good care of your car, including its emission system. If you use preventative maintenance, and keep your car tuned properly, you will pass. If you tamper with your emissions system, you will not pass. You can have your car checked independently before your emissions test if you want to resolve problems before going to the emissions test station. One other good thing to do is to save your printouts from the test from year to year. If you compare them, you will be able to monitor your car (if its score is getting worse) and catch any problems before the emissions people catch you. The Emission Control System The purpose of the emission control system is just that; it controls the emissions and exhaust from your vehicle. The idea is to turn the harmful gases your car manufactures into harmless ones that don't ruin the environment, or us. Some of the problem gases are: • hydrocarbons (unburned) • carbon monoxide • carbon dioxide • nitrogen oxides • sulfur dioxide • phosphorus • lead and other metals To help control these substances, we (along with federal regulations) have made changes in our gasoline to eliminate them.
    [Show full text]
  • Exhaust Muffler Design Principles
    3.0 Exhaust Muffler Design Principles 3.1 Basic Concepts Internal combustion engines are typically equipped with an exhaust muffler to suppress the acoustic pulse generated by the combustion process. A high intensity pressure wave generated by combustion in the engine cylinder propagates along the exhaust pipe and radiates from the exhaust pipe termination. The pulse repeats at the firing frequency of the engine which is defined by f=(engine rpm x number of cylinders)/120 for a four stroke engine. The frequency content of exhaust noise is dominated by a pulse at the firing frequency, but it also has a broadband component to its spectrum which extends to higher frequencies. Measurements of the exhaust pipe pressure pulse on a Continental O- 200 engine [4] show that the majority of the pulse energy lies in the frequency range of 0- 600 Hz. Exhaust mufflers are designed to reduce sound levels at these frequencies. In general, sound waves propagating along a pipe can be attenuated using either a dissipative or a reactive muffler. A dissipative muffler uses sound absorbing material to take energy out of the acoustic motion in the wave, as it propagates through the muffler. Reactive silencers, which are commonly used in automotive applications, reflect the sound waves back towards the source and prevent sound from being transmitted along the pipe. Reactive silencer design is based either on the principle of a Helmholtz resonator or an expansion chamber, and requires the use of acoustic transmission line theory. In a Helmholtz resonator design a cavity is attached to the exhaust pipe.
    [Show full text]
  • Kit Name: KM4 729989-13100 Muffler Kit 1 1 129944-13520
    Kit Name: KM4 YANMAR CO., LTD. YANMAR AMERICA CORP. Item Part No. Description Quantity Remarks 729989-13100 Muffler Kit 1 1 129944-13520 Muffler Kit 1 2 129944-13660 Stay, muffler 1 3 129930-13201 Gasket, Muffler 1 4 123925-13600 Pipe Assy, Tail 1 5 129989-13660 Bracket, muffler 1 6 26306-080002 Nut, M8x1.25 (Flanged hex head) 10 7 26106-080202 Bolt, M8x1.25 - 20 (Flanged hex head) 8 7 5 MODELS 4TNV98-GGE 4TNV98-NSA 1 4TNV98-ZNSA 4 6 3 6 2 7 Notes: Parts code is not assigned to non-serviceable component parts. Remarks: KM4 - MUFFLER KIT PAGE 1 OF 2 INS-KM4-0011 YANMAR CO., LTD. YANMAR AMERICA CORP. Installation Instructions WARNING: DO NOT INSTALL THE KIT WHILE THE ENGINE IS STILL HOT Hand tighten all bolts and nuts until the assembly is completed, then torque to the specifications in Table 1 below. 1. Place the exhaust gasket included with the engine on the exhaust manifold flange studs. 2. Mount the Muffler (1) on the exhaust manifold flange studs so that the outlet faces the radiator, secure using the M8x1.25 flange nuts (6). NOTE: For Step 3, if the Yanmar radiator kit is already installed on the engine it will be necessary to remove the upper mounting bracket from the cylinder head to install the Muffler Bracket (5) for the Muffler. 3. Fasten the Muffler Bracket (5) and the upper radiator mount to the cylinder head using the provided M8x1.25 - 20 bolts 4. Mount the Bracket Stay (2) to the cylinder head and Muffler (1) using the M8x1.25 - 20 bolts (7).
    [Show full text]
  • DESIGN MODIFICATION and ANALYSIS of ENGINE EXHAUST MANIFOLD S.B.Borole1, Dr
    International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056 Volume: 03 Issue: 09 | Sep-2016 www.irjet.net p-ISSN: 2395-0072 DESIGN MODIFICATION AND ANALYSIS OF ENGINE EXHAUST MANIFOLD S.B.Borole1, Dr. G.V.Shah2 [email protected] [email protected] Mechanical Engineering Department, P.V.P.I.T. Bavdhan, Pune University, Pune, Maharashtra, India ---------------------------------------------------------------------***--------------------------------------------------------------------- Abstract - This study focuses on the development of a thermal stresses while welding [4]. This stresses weakens reliable approach to predict failure of exhaust system fitting the materials, produces the defects, which can take shape of and on the removal of structural weaknesses through the small pieces of material, weld spatter, may loose and end up optimization of design. The task with this project was to find a destroying the catalytic converter [5]. Other defects can new solution concept for the connection of pipes into flanges in occur in the welding seam and they must be repaired manifolds. The concept that uses today for their manifolds is manually. However, the manifold should not be based on welding the pipes into place in the flange. The manufactured by casting, because the high temperatures in product development model that is used in this project is present combustion engines demand more expensive and written by Fredy Olsson. For this project have the parts high quality materials that causes problem when casting [7] “Principal construction” and” Primary construction” been [2]. The goal in the development of exhaust system fitting is used. to analyze several solutions weldless. The solutions that are The Objective is to present experimentation, modeling subject for further development are prepared during the and analysis of exhaust system fitting weldless by using FEA.
    [Show full text]
  • 2014 Yamaha SR Viper with Excell Stainless Muffler and XV7 Intake Mod
    2014 Yamaha SR Viper with Excell Stainless muffler and XV7 intake mod. Jim Czekala Aaron Excell of Hubbardsville, NY (www.excellmotorsports.com and www.excellmotorsportspark.com ) brought his new stainless steel glasspack muffler and “XV7” intake mods to DynoTech Research to test on a new Yamaha 2014 SR Viper. Aaron had come to DTR last winter with a beautifully fabricated prototype stainless steel equal length long tube header to test on the Viper, only to be disappointed in the results with either the stock or free flowing Excell muffler. During that session, it became obvious that the biggest gain resulted from reducing exhaust backpressure of the stock muffler. It seems like the three cylinder Yamaha engine’s stock header is well tuned for operation in the 6000-9000 RPM range. With that information, Aaron redirected his efforts to creating intake mods that would remain quiet yet increase airflow, torque and HP without a substantial increase in intake noise. One part of the Excell XV7 intake kit is three machined billet aluminum velocity stacks that would prove to add lots of midrange airflow, torque and HP. And importantly, Aaron created an outside air intake that will drastically reduce intake temperature/ air density and increase actual observed (uncorrected) horsepower. Remember, the rule of thumb is that we gain 1% observed horsepower for every 10 degree F drop in intake charge temperature! While we don’t know the actual intake air temperature of the Viper in winter riding, it’s safe to say the stock airbox intake temperature is much higher than outside air.
    [Show full text]
  • Mopar Perf Parts Catalog.Pdf
    AT MOPAR ®, WE TURN CARS INTO SOMETHING MORE. INTO SOMETHING YOU PASS ON. INTO MYTH. INTO A LEGEND. EVERY PART IS PART OF A LEGACY. AND THAT LEGACY IS YOURS. DODGE CHALLENGER DODGE VIPER 8 Air Induction Systems 38 Brakes 06 9 Exhaust Systems 36 39 Suspension and Steering 10 Suspension Upgrades and Components 39 Wheels 12 Shaker Hoods and Kits 12 T/A Performance Hoods and Components 14 Wheels CHRYSLER 300 42 Air Induction Systems 15 Brakes 40 42 Exhaust Systems 16 Stage Packages 43 Filter 17 Bee-Liever Packages 44 Suspension Upgrades and Components 17 Powertrain Control Modules 46 Stage Performance Packages 17 Filter 47 Brakes DODGE CHARGER 47 Powertrain Control Modules 20 Air Induction Systems RAM 1500 18 20 Exhaust Systems 50 Air Induction Systems 21 Brakes 48 51 Exhaust Systems 21 Wheels 52 Suspension Upgrades and Components 22 Suspension Upgrades and Components 54 Leveling Kits 24 Stage Packages 55 Wheels 25 Bee-Liever Packages 25 Powertrain Control Modules 25 Filter RAM 2500/3500 58 Winch & Mounting Components 56 58 Leveling Kits DODGE DURANGO 59 Lift Kits 28 Air Induction 59 Steering 26 29 Exhaust Systems 29 Suspension Upgrades PERFORMANCE DODGE DART 60GAUGES & LIGHTS 32 Air Induction Systems 62 Gauges 30 32 Exhaust Systems 65 Gauge Pods 33 Performance Hood and Venting 66 SilverStar Lighting 34 Aerodynamics 35 Brakes 35 Suspension Upgrades LIMITED 35 Wheels *Many images shown throughout the catalog are representative 68WARRANTIES of the product. Actual product may vary. WHY US? THAT’S A GOOD QUESTION. For starters, we were there when your car was just a sparkle in a designer’s eye.
    [Show full text]
  • Catalytic Converter (PDF)
    UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, D.C. 20460 Mb8 131991 OFFICE OF AIR AND- RADIATION To whom may it concern: As you know, the Clean Air Act was amended on November 15, 1990. Several of the changes in the Amendments affect the automotive repairfservice industry directly. These changes include the expansion of the tampering prohibition to include private individuals and the prohibition against the manufacture, installation, sale or offering for sale of any part or component used on any motor vehicle or motor vehicle engine where a principal effect is to bypass, defeat, or render inoperative any emission control device or element of design of any emission control system. The enclosed Fact Sheet: Exhaust Svstem ReDair Guidelines has been revised to Conform to the new provisions of the Clean Air Act and represents a change in our enforcement policy with regard to exhaust repair. This change is effective immediately. Essentially, the changes in these guidelines reflect EPA'S position that any pipe used to replace the section of exhaust where the catalytic converter should be, would be considered illegal under the revised Clean Air Act. Therefore, any work in this area of the exhaust system must include proper converter replacement. Other informational materials will be revised to reflect-the Clean Air Act Amendments and will be distributed and made available when they are completed. These other materials include pamphlets - on the tampering prohibition, revised engine switching fact sheet, and possibly a revision of our enforcement policy statement (Memorandum lA) andfor guidance on which parts EPA considers to be illegal.
    [Show full text]
  • Accessories Gasket Identification Charts
    ACCESSORIES GASKET IDENTIFICATION CHARTS Figure 1 Figure 2 (Continued) Figure 3 (Continued) Gasket No. A B Gasket No. A B 31390 2Z\v 2M\, 31610 2CZ\cx B\cx A B 31553 2C\cx 2M\zn 31612 2CM\nv B\cx 31559 2Z\zn 2ZC\zn 31616 2B\, C\zn 31571 ZC\zn M\zn 31628 C\zn C\zn Gasket No. A B 2 4 2 31582 2 2C\, 31629 2CZ\cx C\zn 31301 2Z\, 2M\, 31589 2Z>\cx 3ZC\cx 31631 2M\zn C\, 31307c 2Z\v 3Z\x 31595 C\cx B\nv 31633 >\cx C\zn 31309 1M\, 3 2 3 2 31599 >\cx C\, 31634 C\zn 31310 2 3Z\x 2 3 3 Z\x 31311 2M\zn 3X>\cx 31611 2ZC\zn 3M\cx 31639 2C\, 31313 2Z\zn 3C\, 31638 3 3ZC\zn 31656 1M\zn C\zn 31335 XC\cx 2 2 31641 2 4 31670 2Z\x Z\zn 31336c Z\, Z\x 2 3 * 31650 2M\zn 3Z\v 31696 5 C\zn 31337 2Z\x 4 31711 2Z\x 3 31703 3 C\zn 31356 1Z\x 2ZC\zn 31723 5 5Z\v c Shipped in lots of 10 - Std. Carton. 31367c 2 3C\zn 31726 M\, >\zn 31386 2Z\v 3Z\x* 2 3 31727 M\, B\, 31388 2 3ZZ\cx 2 3 31512 2B\, 4Z\v 31728 2Z\v 3ZC\cx 31532 2C\, 4B\zn 31737 2Z>\cx 3C>\nv Figure 4 31534 Z\, B\, 2 3 36491 4 5Z\v 31537 C\, B\, 2 3 36496 4Z\x 5Z\v 31540 ZB\cx Z\, 2 4 Figure 3 B 31547 M\zn ZM\cx 2 3 B 31560 2Z\zn 4B\zn 31564 C\v 1Z\x* A A 31574 3Z\cx 5B\cx 31578 2XB\nv 4>\nv 31605 2ZC\zn 5B\cx Gasket No.
    [Show full text]
  • Analysis and Design of a Semi-Active Muffler
    Analysis and design of a semi-active muffler PETTER SVANBERG Master of Science Thesis Work in Sound, Vibrations and Signals Stockholm October 2011 Abstract In this work, a flow reversal resonator fitted with a short-circuit duct connecting the inlet and outlet is analysed and used as a tuneable muffler element, aimed to be used use in a semi-active muffler on an IC-engine. The work done can be divided into 3 main parts. 1), a study of what type of valve that could be used to change the acoustical properties of the short-circuit duct. 2), Design of a flow reversal resonator with a controllable valve as the short-circuit. 3), experimental validation in a flow acoustic test rig. The flow reversal resonator with a controllable valve as short-circuit is successfully validated to work as tuneable muffler element during laboratory conditions. The same valve concept is simulated in a full scale concept but not validated experimentally on a running IC-engine. The theory used to describe the acoustics of a flow duct element is also presented together with three simulation techniques and the two microphone technique used to determine the acoustic properties of the investigated flow reversal resonator. Acknowledgement First of all, I want to thank my supervisors, Ragnar Glav at Scania, Mikael Karlsson at SWENOX and Mats Åbom at MWL-KTH for their great support during this work. I have learned a lot and developed my acoustic and engineering skills. I also want to thank Danilo Prelevic at the MWL laboratory for his helpfulness and skills in constructing prototypes and Andreas Holmberg at MWL-KTH for useful tips during the measurements.
    [Show full text]
  • Chrysotile Asbestos Exposure Associated with Removal of Automobile Exhaust Systems (Ca
    Journal of Exposure Science and Environmental Epidemiology (2006) 16, 156–171 r 2006 Nature Publishing Group All rights reserved 1559-0631/06/$30.00 www.nature.com/jes Chrysotile asbestos exposure associated with removal of automobile exhaust systems (ca. 1945–1975) by mechanics:Results of a simulation study DENNIS J. PAUSTENBACH,a AMY K. MADL,a ELLEN DONOVAN,a KATHERINE CLARK,a KURT FEHLINGa AND TERRY C. LEEb aChemRisk, Inc., San Francisco, CA, USA bCarolina EHS, Lake Wylie, SC, USA For decades, asbestos-containing gaskets were used in virtually every system that involved the transport of fluids or gases. Prior to the mid-1970s, some automobile exhaust systems contained asbestos gaskets either at flanges along the exhaust pipes or at the exhaust manifolds of the engine. A limited number of automobile mufflers were lined with asbestos paper. This paper describes a simulation study that characterized personal and bystander exposures to asbestos during the removal of automobile exhaust systems (ca. 1945–1975) containing asbestos gaskets. A total of 16 pre-1974 vehicleswith old or original exhaust systems were studied. Of the 16 vehicles, 12 contained asbestos gaskets in the exhaust system and two vehicles had asbestos lining inside the muffler. A total of 82 samples (23 personal, 38 bystander, and 21 indoor background) were analyzed by Phase Contrast Microscopy (PCM) and 88 samples (25 personal, 41 bystander, and 22 indoor background) by Transmission Electron Microscopy (TEM). Only seven of 25 worker samples analyzed by TEM detected asbestos fibers and 18 were below the analytical sensitivity limit (mean 0.013 f/cc, range 0.001–0.074 f/cc).
    [Show full text]