Kit Name: KM4 729989-13100 Muffler Kit 1 1 129944-13520

Total Page:16

File Type:pdf, Size:1020Kb

Kit Name: KM4 729989-13100 Muffler Kit 1 1 129944-13520 Kit Name: KM4 YANMAR CO., LTD. YANMAR AMERICA CORP. Item Part No. Description Quantity Remarks 729989-13100 Muffler Kit 1 1 129944-13520 Muffler Kit 1 2 129944-13660 Stay, muffler 1 3 129930-13201 Gasket, Muffler 1 4 123925-13600 Pipe Assy, Tail 1 5 129989-13660 Bracket, muffler 1 6 26306-080002 Nut, M8x1.25 (Flanged hex head) 10 7 26106-080202 Bolt, M8x1.25 - 20 (Flanged hex head) 8 7 5 MODELS 4TNV98-GGE 4TNV98-NSA 1 4TNV98-ZNSA 4 6 3 6 2 7 Notes: Parts code is not assigned to non-serviceable component parts. Remarks: KM4 - MUFFLER KIT PAGE 1 OF 2 INS-KM4-0011 YANMAR CO., LTD. YANMAR AMERICA CORP. Installation Instructions WARNING: DO NOT INSTALL THE KIT WHILE THE ENGINE IS STILL HOT Hand tighten all bolts and nuts until the assembly is completed, then torque to the specifications in Table 1 below. 1. Place the exhaust gasket included with the engine on the exhaust manifold flange studs. 2. Mount the Muffler (1) on the exhaust manifold flange studs so that the outlet faces the radiator, secure using the M8x1.25 flange nuts (6). NOTE: For Step 3, if the Yanmar radiator kit is already installed on the engine it will be necessary to remove the upper mounting bracket from the cylinder head to install the Muffler Bracket (5) for the Muffler. 3. Fasten the Muffler Bracket (5) and the upper radiator mount to the cylinder head using the provided M8x1.25 - 20 bolts 4. Mount the Bracket Stay (2) to the cylinder head and Muffler (1) using the M8x1.25 - 20 bolts (7). 5. Place Muffler Gasket (3) on the studs of the Muffler outlet. 6. Mount the Elbow Pipe (4) to the suds on the Muffler outlet and fasten with M8x1.25 flange nuts (6) 7. Torque all bolts to proper torque specifications. Table 1: Proper torque specifications for bolts and nuts. Diameter x Pitch Kgf-m Foot-lbf N-m M8 x 1.25 1.5 ~ 2.9 10.6 ~ 20.9 14.4 ~ 28.3 M10 x 1.50 4.5 ~ 5.5 32.5 ~ 39.8 44.0 ~ 54.0 M12 x 1.75 8.0 ~ 10.0 57.8 ~ 72.3 78.4 ~ 98.0 KM4 - MUFFLER KIT PAGE 2 OF 2 INS-KM4-0011.
Recommended publications
  • Engine Components and Filters: Damage Profiles, Probable Causes and Prevention
    ENGINE COMPONENTS AND FILTERS: DAMAGE PROFILES, PROBABLE CAUSES AND PREVENTION Technical Information AFTERMARKET Contents 1 Introduction 5 2 General topics 6 2.1 Engine wear caused by contamination 6 2.2 Fuel flooding 8 2.3 Hydraulic lock 10 2.4 Increased oil consumption 12 3 Top of the piston and piston ring belt 14 3.1 Hole burned through the top of the piston in gasoline and diesel engines 14 3.2 Melting at the top of the piston and the top land of a gasoline engine 16 3.3 Melting at the top of the piston and the top land of a diesel engine 18 3.4 Broken piston ring lands 20 3.5 Valve impacts at the top of the piston and piston hammering at the cylinder head 22 3.6 Cracks in the top of the piston 24 4 Piston skirt 26 4.1 Piston seizure on the thrust and opposite side (piston skirt area only) 26 4.2 Piston seizure on one side of the piston skirt 27 4.3 Diagonal piston seizure next to the pin bore 28 4.4 Asymmetrical wear pattern on the piston skirt 30 4.5 Piston seizure in the lower piston skirt area only 31 4.6 Heavy wear at the piston skirt with a rough, matte surface 32 4.7 Wear marks on one side of the piston skirt 33 5 Support – piston pin bushing 34 5.1 Seizure in the pin bore 34 5.2 Cratered piston wall in the pin boss area 35 6 Piston rings 36 6.1 Piston rings with burn marks and seizure marks on the 36 piston skirt 6.2 Damage to the ring belt due to fractured piston rings 37 6.3 Heavy wear of the piston ring grooves and piston rings 38 6.4 Heavy radial wear of the piston rings 39 7 Cylinder liners 40 7.1 Pitting on the outer
    [Show full text]
  • Mr. Gasket Catalog
    Restore. Restyle. Relive. PRODUCT CATALOG THE MR. GASKET STORY Back in 1964, Joe Hrudka was a drag racer in Northern Ohio who was looking to solve a problem that parts manufacturers had not addressed. Using his own 1957 Chevy drag race car as a test vehicle, he created a line of engine gaskets and fasteners proven to seal and withstand extreme temperatures, pressures and stresses created by high performance engines. This product line that was developed by a drag racer would evolve into a brand of legendary proportions over the next 50 years. Mr. Gasket started with Joe’s ‘57 Chevy and has continued to advance and expand with application coverage and even more new products for muscle cars. Head gaskets, exhaust gaskets and oil pan gaskets were just the beginning. The Mr. Gasket brand develops and distributes a variety of performance parts for your vehicle including: carburetor and fuel accessories, chrome-plated accessories, cooling system accessories, engine components, fuel additives, shifter accessories, specialty tools, suspension and driveline components. Located in Cleveland, Ohio, the Mr. Gasket team continues to design, develop, manufacture and distribute products that bring back the luster and performance that everyone remembers to a variety of auto projects. It may have started with a Chevrolet, but when you are ready to Restore, Restyle and Rebuild your car, Mr. Gasket is who you can trust to have the parts and advice you need to complete your project. Find out about all of the Mr. Gasket products and applications at www.mr-gasket.com www.mr-gasket.com TABLE OF CONTENTS CHEMICALS .......................................................................
    [Show full text]
  • Oil Leaks from Valve Cover Gasket 19-2309
    Page 1 of 5 TECHNICAL SERVICE BULLETIN 19-2309 5.0L - Oil Leaks From Valve Cover Gasket 16 October 2019 This bulletin supersedes 19-2260. Reason for update: Incorrect or Incomplete Symptom Model: Ford 2015-2017 Mustang Summary This article supersedes TSB 19-2260 to update the Issue Statement and Service Procedure. Issue: Some 2015-2017 Mustang vehicles equipped with a 5.0L engine may exhibit an oil leak from either valve cover gasket. This may be due to the valve covers warping due to excessive heat. To correct the condition, follow the Service Procedure steps to add fasteners to both valve covers. Action: Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria: • 2015-2017 Mustang • 5.0L engine • Oil leak from either valve cover gasket Parts Part Number Description Quantity JR3Z-00812-B Valve Cover Bolt (Package Contains 1 Piece, 8 Pieces Required) 8 W712334-S440 Strut Tower Brace/Cowl Extension Nut (Package Contains 3 Pieces, 4 2 Pieces Required) ER3Z-6584-B Valve Cover Gasket (Left Side) 1 ER3Z-6584-A Valve Cover Gasket (Right Side) 1 BR3Z-6C535-A As VCT Seal Needed BR3Z-6C535-B As Spark Plug Seal Needed ZC-30-A As Motorcraft® Silicone Gasket Remover Needed ZC-31-B As Motorcraft® Metal Surface Prep Wipes Needed TA-30 As Motorcraft® Silicone Gasket and Sealant Needed PM-4-A As Motorcraft® Metal Brake Parts Cleaner Needed XO-5W20- Motorcraft® SAE 5W-20 Synthetic Blend Motor Oil (All Markets Except As Q1SP Canada) Needed CXO-5W20- As Motorcraft® SAE 5W-20 Super Premium Motor Oil (Canada Only) LSP6 Needed http://www.fordservicecontent.com/Ford_Content/vdirsnet/TSB/EU/~WTSB19 -2309/US/ ..
    [Show full text]
  • DMF Muffler Offers a New Level of Emission Reduction for 1991-2002 Model Year Diesel-Powered Engines
    A High Efficiency Emissions Retrofit Solution with No Maintenance – The Diesel Multi-stage Filter (DMF) Muffler The patented 1 Donaldson DMF Muffler offers a new level of emission reduction for 1991-2002 model year diesel-powered engines. As a tailpipe solution, this product will reduce your diesel PM emissions up to 60%! Reduce your total vehicle emissions even more with our patented 2 combination – the DMF Muffler and Spiracle™ Crankcase Filtration System. 1 U.S. Pat. No. 7,340,888 2 U.S. Pat No. 7,278,259; 7,257,942 High Efficiency Filtration with No Maintenance .... our DMF Mufflers DO NOT require routine ash cleaning Partial Flow Through Filter Broad Engine Coverage The DMF Muffler uses a two- • Approved for four-stroke on-road diesel engine applications stage metallic filter to trap with engine horsepower ranges of 150-600 hp and reduce diesel particulate - 1991-1993 model year engines (0.25 g/bhp-hr PM or less) matter (PM). Each filter with exhaust temperatures of 230º C for 40% of the time stage consists of alternating and average exhaust temperature of 215º C or above layers of a corrugated metal and a porous sintered metal - 1994-2002 model engines (0.10 g/bhp-hr PM or less) fleece. The unique catalyst with exhaust temperatures of 210º C for 40% of time and coating reduces PM, HC and average exhaust temperature of 210º C or above CO, while minimizing NO2 • For even more emissions reduction, consider ordering a emissions (<20% increase). kit that includes the Donaldson closed crankcase filtration system - Spiracle™ and DMF Muffler.
    [Show full text]
  • Flowmaster Exhaust Systems Are Designed Vehicle Specific and Do Not Violate the Manufacturer’S Factory Warranty
    2016 MUFFLERS // SYSTEMS // HEADERS // CATALYTIC CONVERTERS // TIPS & ACCESSORIES FLOWMASTER MANUFACTURING Shown in a rare quiet moment, Flowmaster’s state-of-the-art manufacturing plant in Northern California features many self-designed tools and high-tech robotics to build the world’s most advanced mufflers. For over three decades, Flowmaster has led the way in automotive performance exhaust technology with some of the earliest product patents held by an exhaust manufacturer. As the world’s first fully welded muffler in 1983, Flowmaster raised the bar for durability and strength, while singlehandedly reinventing the performance exhaust industry. Today, we maintain that edge with constant innovation in exhaust solutions for street, race, and off-road applications. 2 WWW.FLOWMASTERMUFFLERS.COM TECHNOLOGY CAR APP 05 12 HEADERS TRUCK APP 06 34 CONVERTERS MUFFLERS 08 50 RACE PARTS Tech Support: 1-707-544-4761 www.flowmastermufflers.com 66 ACCESSORIES 72 The Exclusive Performance Exhaust Of NASCAR INFO / FAQ FIND US ON: 80 NOTE: Flowmaster’s muffler recommendations are based on OEM configurations, but are not considered direct-fit replacements. Our universal mufflers may require modification during installation. Additional muffler options may apply outside of these recommendations. Should you have any questions, call our tech line for further assistance in selecting a system or muffler. WWW.FLOWMASTERMUFFLERS.COM 3 ABOUT THE COMPANY For over 30 years, Flowmaster has been the leader in advanced exhaust technology through our extensive commitment to research and development. Early on we learned that by understanding an engine’s total operation, we could not only generate a terrific performance exhaust sound, but more importantly increase combustion efficiency and improve both performance and fuel mileage.
    [Show full text]
  • Exhaust/Emissions Systems Overview Emissions Testing
    Exhaust/Emissions Systems Overview Below is an overview of this system's operation Emissions Testing Many states require emissions tests on vehicles. This means that you drive to a facility where the test people take a sample of your emissions and run it through some analysis. The results are printed,and you pass or fail depending on the percentage of toxic emissions that turn up in your car's sample. The only way to "study" or prepare for this test is to take good care of your car, including its emission system. If you use preventative maintenance, and keep your car tuned properly, you will pass. If you tamper with your emissions system, you will not pass. You can have your car checked independently before your emissions test if you want to resolve problems before going to the emissions test station. One other good thing to do is to save your printouts from the test from year to year. If you compare them, you will be able to monitor your car (if its score is getting worse) and catch any problems before the emissions people catch you. The Emission Control System The purpose of the emission control system is just that; it controls the emissions and exhaust from your vehicle. The idea is to turn the harmful gases your car manufactures into harmless ones that don't ruin the environment, or us. Some of the problem gases are: • hydrocarbons (unburned) • carbon monoxide • carbon dioxide • nitrogen oxides • sulfur dioxide • phosphorus • lead and other metals To help control these substances, we (along with federal regulations) have made changes in our gasoline to eliminate them.
    [Show full text]
  • IM-391 April 2020
    Inline Fume Exhaust Fans IM-391 April 2020 General Installation, Operation and Maintenance Instructions For Aerovent Products Throughout this manual, there are a number of HAZARD WARNINGS that must be read and adhered to in order to prevent possible personal injury and/or damage to equipment. Two signal words "WARNING" and "CAUTION" are used to indicate the severity of a hazard and are preceded by the safety alert symbol. WARNING Used when serious injury or death MAY result from misuse or failure to follow specific instructions. CAUTION Used when minor or moderate injury or product / equipment damage MAY result from misuse or failure to follow specific instructions. NOTICE Indicates information considered important, but not hazard-related. It is the responsibility of all personnel involved in installation, operation and maintenance to fully understand the Warning and Caution procedures by which hazards are to be avoided. INTRODUCTION This manual has been prepared to guide the users of AFE Fume Exhaust Fans in the proper installation, operation and maintenance procedures to insure maximum equipment life with trouble-free operation. AFE CONTENTS Inspection and Receiving ..................................................2 Handling and Rigging ........................................................2 CAUTION Unit Storage ........................................................................2 Installation Fan systems include rotating components and • Pre-Installation Checklist ..........................................2 electrical devices.
    [Show full text]
  • United States Patent 19 L L 3,948,227 Guenther 45) Apr
    United States Patent 19 l l 3,948,227 Guenther 45) Apr. 6, 1976 54 STRATIFED CHARGE ENGINE 57 ABSTRACT 76 Inventor: William D. Guenther, R.R. 2, An apparatus for applying a stratified charge to a re Hagerstown, Ind. 47346 ciprocating internal combustion engine is disclosed. 22 Filed: Mar. 8, 1974 The apparatus comprises a cylindrical rotary valve body disposed for rotation within the head of an inter 21 ) Appl. No.: 449,241 nal combustion engine. The valve body defines dia metrically extending inlet and exhaust passages which, 52 U.S. C. ....... 123/32 SP; 123175 B; 123/190 A; during rotation of the valve body, place a cylinder of 123/190 B; 123/190 BD; 123/80 BA the engine in sequential communication with an inlet 5 i Int. Cl........................ F02B 19/10; FO1 L7/00 manifold and an exhaust manifold secured to the 58) Field of Search........... 123/32 ST, 32 SP, 75 B, head. The inlet manifold comprises a double-passage 123/80 BA, 33 VC, 190 R, 190 B, 190 BB, gallery for transporting a lean fuel/air charge in a first 190 BD, 190 D, 190 C, 127 passage and a rich fuel/air charge in a second passage. Rotation of the inlet passage into communication with (56) References Cited the cylinder also brings the inlet passage into sequen UNITED STATES PATENTS tial communication with the first throat and then the 194,047 8/1877 Otto.................................. 123,175 B second throat for transporting the first lean charge 1,594,664 8/1926 Congellier......................... 123,175 B and then the second rich charge to the cylinder.
    [Show full text]
  • Exhaust Muffler Design Principles
    3.0 Exhaust Muffler Design Principles 3.1 Basic Concepts Internal combustion engines are typically equipped with an exhaust muffler to suppress the acoustic pulse generated by the combustion process. A high intensity pressure wave generated by combustion in the engine cylinder propagates along the exhaust pipe and radiates from the exhaust pipe termination. The pulse repeats at the firing frequency of the engine which is defined by f=(engine rpm x number of cylinders)/120 for a four stroke engine. The frequency content of exhaust noise is dominated by a pulse at the firing frequency, but it also has a broadband component to its spectrum which extends to higher frequencies. Measurements of the exhaust pipe pressure pulse on a Continental O- 200 engine [4] show that the majority of the pulse energy lies in the frequency range of 0- 600 Hz. Exhaust mufflers are designed to reduce sound levels at these frequencies. In general, sound waves propagating along a pipe can be attenuated using either a dissipative or a reactive muffler. A dissipative muffler uses sound absorbing material to take energy out of the acoustic motion in the wave, as it propagates through the muffler. Reactive silencers, which are commonly used in automotive applications, reflect the sound waves back towards the source and prevent sound from being transmitted along the pipe. Reactive silencer design is based either on the principle of a Helmholtz resonator or an expansion chamber, and requires the use of acoustic transmission line theory. In a Helmholtz resonator design a cavity is attached to the exhaust pipe.
    [Show full text]
  • Gruvlok Gasket-Styles
    TECHNICAL DATA SHEETS TECHNICAL DATA SHEETS GRUVLOK GASKET-STYLES Gruvlok offers a variety of pressure responsive gasket styles. Each serves a specific function while utilizing the same basic sealing concept. Proper installation of the gasket compresses the inclined gasket lips on the pipe O.D., forming a leak tight seal. This sealing action is reinforced when the gasket is encompassed and compressed by the coupling housings. The application of internal line pressure energizes the elastometric gasket and further enhances the gasket sealing action. “C” STYLE The “C” Style cross section configuration is the most widely used ® gasket. It is the gasket style provided ROUGHNECK as standard in many Gruvlok Couplings This “C” style gasket is (Fig. 7000, 7001, 7003, 7004HPR, 7307, similar in appearance 7400 and 7401). Grade “E” and “T” are standard grades while other grades and design to the are available for special applications. Standard gasket but is only used with Fig. 7005 ™ END GUARD Roughneck Couplings The projecting rib fits between the ends and Fig. 7305 HDPE Couplings. The Roughneck gasket is wider, which allows of lined pipe to prevent damage to for minor pipe end separation as line pressure sets the grippers into the unprotected pipe ends during coupling plain end pipe. joint assembly. The E.G. gasket is provided as standard with the Fig. 7004 E.G. Coupling. REDUCING COUPLING Grade “E” and “T” gaskets are available. The centering rib allows for pipe positioning and serves FLUSH GAP™ to keep the smaller pipe from telescoping during installation. Designed to prohibit contaminates Used only with the Fig.
    [Show full text]
  • Gasket CRITERIA
    Gasket CRITERIA. designcriteria 04-14_inside 3/24/2016 1:46 PM Page 1 ­­­Gasket­Design­Criteria Table­of­Contents Page Manufacturing­Units 2 Introduction 3 Section­I­-­Gasket­Selection 4 Change Gasket ................................................................................................................................ 6 Sheet Materials ................................................................................................................................ 8 Thermiculite® .................................................................................................................................... 9 PTFE Products - Sigma® ................................................................................................................... 12 PTFE Products - Fluoroseal .............................................................................................................. 14 Flexitallic Flexicarb® .......................................................................................................................... 15 Compressed Fiber Gasket ................................................................................................................ 16 Core4 Sheet Products ...................................................................................................................... 17 Sheet Materials Chemical Compatibility Chart ................................................................................. 18 Insulating Sets .................................................................................................................................
    [Show full text]
  • Head Gasket Repair
    Head Gasket Repair aceautoutah.com /head-gasket-repair/ If you’re in need of having your head gasket repaired, you need to look no further than Ace’s Auto Repair, located in West Jordan, Utah. We can fix your head gasket, and we offer competitive rates. We employ servicemen that are experienced and certified, and we are able to repair every sort of vehicle in every make and model. This includes: SUVs Trucks Vans Cars What Does a Head Gasket Do? As part of your vehicle’s internal combustion engine, both oil and coolant play an integral role in the functioning of your automobile, and it is vital that these both be kept separate from each other. The head gasket acts as a seal, and it is situated between the engine block and the cylinder head. It is important that the oil and coolant remain in their own channels and that they don’t leak into the combustion chamber, out of the engine altogether, or into each other’s chambers. Your engine’s head gasket is continually subject to contrasting temperatures and conditions. It is exposed to the heat that is produced in the combustion chamber, and it is subject to the cold that is produced by the components that are designed to keep your vehicle cool. It is shaped like a panel with one circle for every cylinder that the engine houses. This environment of extremes can sometimes cause your head gasket to warp, and if left untended, this can cause your head gasket to blow. What Are Some Ways to Tell That My Head Gasket Has Blown? It is crucial that you be able to recognize the signs and symptoms that you’re dealing with a blown head gasket.
    [Show full text]