DOCSLIB.ORG

2015 Oklahoma Minimum School Bus Specifications

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
2015 Oklahoma Minimum School Bus Specifications 2015 Oklahoma Minimum School Bus Specifications These specifications will be in effect beginning April 1, 2018. AIR CLEANER A. A dry element air cleaner shall be provided. B. All diesel engine air filters shall include a latch-type restriction indicator that retains the maximum restriction developed during operation of the engine. The indicator should include a reset control so the indicator can be returned to zero when desired. AISLE All emergency exit doors shall be accessible by a 12-inch minimum aisle. The aisle shall be unobstructed at all times by any type of barrier, seat, wheelchair or tie-down, unless a flip seat is installed and occupied. The track of a track seating system is exempt from this requirement. A flip seat in the unoccupied (up) position shall not obstruct the 12-inch minimum aisle to any side emergency exit door. AXLES The front and rear axle and suspension systems shall have a gross axle weight rating (GAWR) at ground commensurate with the respective front and rear weight loads of the bus loaded to the rated passenger capacity. BACK-UP WARNING ALARM An automatic audible alarm shall be installed behind the rear axle and shall comply with the published Backup Alarm Standards (SAE J994b), providing a minimum of 112 dBA, or shall have a variable volume feature that allows the alarm to vary from 87 dBA to 112 dBA sound level, staying at least 5 dBA above the ambient noise level. BRAKES: GENERAL A. The chassis brake system shall conform to the provisions of FMVSS Nos. 105, Hydraulic and Electric Brake Systems, 106, Brake Hoses, and 121, Air Brake Systems, as applicable. All buses shall have either a parking pawl in the transmission or a park brake interlock that requires the service brake to be applied to allow release of the parking brake. B. The anti-lock brake system (ABS), provided in accordance with FMVSS No. 105, Hydraulic and Electric Brake Systems or No. 121, Air Brake Systems, shall provide wheel speed sensors for each front wheel and for each wheel on at least one rear axle. The system shall provide anti-lock braking performance for each wheel equipped with sensors (Four Channel System). C. All brake systems shall be designed to permit visual inspection of brake lining wear without removal of any chassis component(s). D. The brake lines, booster-assist lines, and control cables shall be protected from 1 excessive heat, vibration and corrosion and installed in a manner that prevents chafing. E. The parking brake system for either air or hydraulic service brake systems may be of a power-assisted design. The power parking brake actuator should be a device located on the instrument panel within reach of seated a 5th percentile female driver. As an option, the parking brake may be set by placing the automatic transmission shift control mechanism in the “park” position. F. The power-operated parking brake system may be interlocked to the engine key switch. Once the parking brake has been set and the ignition switch turned to the “off” position, the parking brake cannot be released until the key switch is turned back to the “on” position. BRAKES: HYDRAULIC Buses using hydraulic-assist brakes shall meet requirements of FMVSS 105. BRAKES: AIR A. The air pressure supply system shall include a desiccant-type air dryer installed according to the manufacturer’s recommendations. The air pressure storage tank system shall incorporate an automatic drain valve. B. The chassis manufacturer shall provide an accessory outlet for air-operated systems installed by the body manufacturer. This outlet shall include a pressure protection valve to prevent loss of air pressure in the service brake reservoir. C. For air brake systems, an air pressure gauge shall be provided in the instrument panel capable of complying with Commercial Driver’s License (CDL) pre-trip inspection requirements. D. Air brake systems shall include a system for anti-compounding of the service brakes and parking brakes. E. Air brakes shall have both a visible and audible warning device whenever the air pressure falls below the level where warnings are required under FMVSS No. 121, Air Brake Systems. BUMPER: FRONT A. School buses shall be equipped with a front bumper. B. The front bumper on buses of Type A-2 (with GVWR greater than 14,500 pounds), Type B, Type C, and Type D shall be equivalent in strength and durability to pressed steel channel at least 3/16 inches thick and not less than 8 inches wide (high). It shall extend beyond the forward-most part of the body, grille, hood and fenders and shall extend to the outer edges of the fenders at the bumper’s top line. Type A buses having a GVWR of 14,500 pounds or less may be equipped with an OEM-supplied front bumper. The front bumper shall be of sufficient strength to permit being pushed by another vehicle on a smooth surface with a 5 degree, (8.7 percent) grade, without permanent distortion. The contact point on the front bumper is intended to be between the frame rails with as wide a contact area as possible. If the front bumper is used for lifting, the contact points shall be under the bumper attachments to the frame rail brackets unless the 2 manufacturer specifies different lifting points in the owner’s manual. Contact and lifting pressures should be applied simultaneously at both lifting points. C. The front bumper, except breakaway bumper ends, shall be of sufficient strength to permit pushing a vehicle of equal gross vehicle weight, per Section B, without permanent distortion to the bumper, chassis or body. D. The bumper shall be designed or reinforced so that it will not deform when the bus is lifted by a chain that is passed under the bumper (or through the bumper if holes are provided for this purpose) and attached to both tow hooks/eyes. For the purpose of meeting this specification, the bus shall be empty and positioned on a level, hard surface and both tow hooks/eyes shall share the load equally. BUMPER: REAR A. The bumper on Type A-1 buses shall be a minimum of 8 inches wide (high). Bumpers on Types A-2, B, C and D buses shall be a minimum of 9½ inches wide (high). The bumper shall be of sufficient strength to permit being pushed by another vehicle of similar size and being lifted by the bumper without permanent distortion. B. The bumper shall wrap around the back corners of the bus. It shall extend forward at least 12 inches, measured from the rear-most point of the body at the floor line, and shall be mounted flush with the sides of the body or protected with an end panel. C. The bumper shall be attached to the chassis frame in such a manner that it may be removed. It shall be braced to resist deformation of the bumper resulting from impact from the rear or the side. It shall be designed to discourage hitching of rides by an individual. D. The bumper shall extend at least one inch beyond the rear-most part of the body surface, measured at the floor line. E. The bottom of the rear bumper shall not be more than 30 inches above ground level. CERTIFICATION Upon request of the state agency having student transportation jurisdiction, the chassis and body manufacturer(s) shall certify that its(their) product(s) meets the state’s minimum standards on items which are not covered by FMVSS certification requirements of 49 CFR, Part 567: Certification. COLOR A. The school bus body shall be painted National School Bus Yellow (NSBY). (See APPENDIX A in National School Transportation Specifications and Procedures 2015) B. The body exterior trim, rub rails and background of red and amber flashers, shall be black or NSBY. Rub rails may be painted in such a way that only the entire raised center section of the rail is black. C. Except for the vertical portion of the front and rear roof caps, the roof of the bus shall be painted white. (See illustration in APPENDIX, Placement of Retroreflective Markings.) 3 D. The chassis and front bumper shall be black. Body, cowl, hood and fenders shall be in National School Bus Yellow (NSBY). The flat top surface of the hood may be non-reflective black or NSBY. (See APPENDIX) E. Wheels may be silver, gray, white, yellow or black. F. Multi-Function School Activity Buses (MFSABs) shall be exempt from these requirements. CONSTRUCTION A. Side Intrusion Test: The bus body shall be constructed to withstand an intrusion force equal to the curb weight of the vehicle or 20,000 pounds, whichever is less. Each vehicle shall be capable of meeting this requirement when tested in accordance with the procedures set forth below. The complete body structure, or a representative seven-body section mock up with seats installed, shall be load tested at a location 24±2 inches above the floor line, with a maximum 10 inch diameter cylinder, 48 inches long, mounted in a horizontal plane. The cylinder shall be placed as close as practical to the mid-point of the tested structure, spanning two internal vertical structural members. The cylinder shall be statically loaded to the required force of curb weight or 20,000 pounds, whichever is less, in a horizontal plane with the load applied from the exterior toward the interior of the test structure. When the minimum load has been applied, the penetration of the loading cylinder into the passenger compartment shall not exceed 10 inches from its original point of contact.
Load more

Recommended publications
  • Allamerican-Web-Ready.Pdf
    Building a BETTER BUS NextGen Seating NEXTGEN SEAT Convertible seating has never been this easy - or this comfortable. Now there is no need to completely remove the entire seat when you want to change the seating configuration. With Blue Bird’s NextGen Seat, simply remove four bolts from the base of the seat cushion and reinstall the new seat that you want - it’s really that simple! Mix-and-match your seats as you need them, making your bus fleet more versatile without the need to spend large amounts of time or money. COMFORTABLE The recessed back pad gives passengers improved knee clearance, and the integrated head rest and built-in lumbar support sets a new standard in student seating comfort. Lap Belt Ready (LBR) INNOVATIVE A first in the Industry, the bottom cushion tilts up allowing for unprecedented access between seats as well as ease of cleaning. CONVERTIBLE Easily converts from one seat type to another by simply removing and reinstalling 4 bolts. 3-Point Belts Child Restraint Available in lap-belt ready, 3-point seat belt, (3PT) (CR) child restraint and 3-point child restraint. OEM Installed Air Conditioning AIR CONDITIONING Aftermarket installation can interfere with the structural design of the bus body, as well as put additional stress on critical engine, chassis and electrical systems. This OEM installation creates less maintenance for you, due to the frame-mount installation of the condensers during chassis assembly, EZ clip connectors which provide a no-leak hose to connector securement, and more. Contact your local dealer today to learn more about Blue Bird’s OEM air conditioning option! Standard Test Compliance Passenger Safety Cage 90 The All American passes Colorado Rack, Blue Bird’s custom designed one-piece LH Kentucky Pole and Altoona Tests in roof bow system ensures safe student its standard configuration, not as an transportation with an exceptionally option like the competition, highlighting strong structure.
    [Show full text]
  • North Dakota
    NORTH DAKOTA SCHOOL BUS DRIVER’S GUIDE MARCH 2015 EDITION DEPARTMENT OF PUBLIC INSTRUCTION Kirsten Baesler, STATE SUPERINTENDENT Bismarck, North Dakota 58505-0440 2 A MESSAGE FROM THE SUPERINTENDENT OF PUBLIC INSTRUCTION Over 40,000 students are transported each day to North Dakota schools in school buses. The safety of these students and the efficiency of a district's transportation program depends on the dedicated men and women who accept the important responsibility of driving our school buses. This publication is the thirteenth edition of the handbook for North Dakota school bus drivers. We hope that this handbook answers many questions and gives school bus drivers the necessary guidelines to perform effectively and efficiently. Driving a school bus involves much more than merely driving a vehicle on the highways. The school bus driver must also be responsible for the safety and welfare of children, must be teacher by example, must promote good public relations, and must understand how to properly use and care for the school bus, a complex and expensive piece of equipment. The purpose of this guide is to provide each school bus driver with the basic information needed to develop the skills, attitudes, and knowledge that result in safe and efficient driving. It is my sincere hope that each of North Dakota's school bus drivers will study and properly apply the information presented in this guide to assure a safer transportation program for our students. Driving a school bus is one of the most important jobs we have in our school systems. You carry our state’s most precious resource.
    [Show full text]
  • Blue Bird Electric School Buses July 21, 2020 All Roads Lead to Blue Bird Electric School Buses
    Blue Bird Electric School Buses July 21, 2020 All Roads Lead to Blue Bird Electric School Buses GVWR 36,200lbs GVWR 33,000lbs 315 HP GVWR 14,500lbs 315 HP Battery Capacity = 155kWh 215 HP Battery Capacity = 155kWh Battery Capacity = 88kWh A long history in alternative fuels ▪ Blue Bird was a pioneer and first school bus OEM to embrace EV technology ▪ 1994 - Collaborated with Westinghouse Electronic Systems to develop first battery- powered school bus ▪ 1996 - Collaborated with Electrosource, Inc. to produce transit style electric shuttle buses for the Atlanta Summer Olympics 3 Present Day 2016 ▪ Blue Bird Received $4.4MM grant from US Department of Energy (US DOE) for the production of 10 V2G school buses. 2017 ▪ Blue Bird Launched our current iteration of the Blue Bird EV bus at the STN Expo, Reno in July 2017 2018 ▪ Blue Bird delivered its first electric-powered school buses to customers in California and Ontario (Canada) 2020 ▪ Blue Bird delivered its one hundredth electric-powered school bus 1 to 100 – in just 20 months! September 2018 April 2020 Blue Bird – Electric School Bus Sales Turn-key solution 7 Total Cost of Ownership (TCO) How do the acquisition cost and operational cost over the life of the vehicle compare to our current fleet? DIESEL VERSUS ELECTRIC COST OF OWNERSHIP Difference Diesel Electric Savings Diesel Bus Cost $100,000 Electric Bus Cost $350,000 $250,000.00 15 Yr lifetime 15 Yr lifetime Over lifetime Buy down $0 * Annual Grant Funding ($167,000) * Annual Replacement cycle 180 Cost over Replacement cycle 180 Cost
    [Show full text]
  • Washington State School Bus Specifications
    Washington State School Bus Specifications Chris Reykdal State Superintendent of Public Instruction Revised September 2019 Except where otherwise noted, this work by the Office of Superintendent of Public Instruction is licensed under a Creative Commons Attribution License. Please make sure that permission has been received to use all elements of this publication (images, charts, text, etc.) that are not created by OSPI staff, grantees, or contractors. This permission should be displayed as an attribution statement in the manner specified by the copyright holder. It should be made clear that the element is one of the “except where otherwise noted” exceptions to the OSPI open license. For additional information, please visit the OSPI Interactive Copyright and Licensing Guide. OSPI provides equal access to all programs and services without discrimination based on sex, race, creed, religion, color, national origin, age, honorably discharged veteran or military status, sexual orientation including gender expression or identity, the presence of any sensory, mental, or physical disability, or the use of a trained dog guide or service animal by a person with a disability. Questions and complaints of alleged discrimination should be directed to the Equity and Civil Rights Director at 360-725-6162 or P.O. Box 47200 Olympia, WA 98504-7200. Download this material in PDF at Student Transportation's Publications website. This material is available in alternative format upon request. Contact the Resource Center at 888-595-3276, TTY 360-664-3631. Please refer to this document number for quicker service: 19-0027. Image Description Chris Reykdal • State Superintendent Office of Superintendent of Public Instruction Old Capitol Building • P.O.
    [Show full text]
  • 2013 Florida School Bus Specifications
    FLORIDA SCHOOL BUS SPECIFICATIONS Revised 2013 TABLE OF CONTENTS Page Foreword .................................................................................................................................................................................... iii General Information and Warranty Provisions ...................................................................................................................... 1 Section I CHASSIS SPECIFICATIONS for types A1 (19-29 capacity) and A2 (30-47 capacity)............................... ..I-1 OPTIONAL CHASSIS EQUIPMENT for Type A ................................................................................................ I-9 Section II CHASSIS SPECIFICATIONS for types C and D ........................................................................................... II-1 OPTIONAL CHASSIS EQUIPMENT for types C and D ................................................................................. II-10 Section III BODY SPECIFICATIONS for types A1, A2, C, and D ................................................................................. III-1 EXCEPTIONS for Type D ................................................................................................................................ III-20 OPTIONAL BODY EQUIPMENT for types A1, A2, C, and D ....................................................................... III-21 Section IV EXCEPTIONAL CHILD BUS SPECIFICATIONS for types A, C, and D ................................................. IV-1 Section V AIR CONDITIONER
    [Show full text]
  • Cost Evaluation for Nine Federal Motor Vehicle Safety Standards
    TL DOT HS- 805 320 242 . H3 82 COST EVALUATION FOR NINE FEDERAL v . 6 MOTOR VEHICLE STANDARDS VOLUME VI FMVSS 220, 221, & 222 M. R. Harvey DEPARTMENT of J. A. Lesczhik transportation R. F. McLean 1 4 1980 De Lorean Motor Company JUL 2401 Elliott Street library Troy, Michigan 48084 J Contract No. D0T-HS-8-02015 Contract Amt. $332,007 NOVEMBER 1979 FINAL REPORT This document is available to the U.S. public through the National Technical Information Service, Springfield, Virginia 22161 Prepared For U.S. DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration Washington, D.C. 20590 This document is disseminated under the sponsorship of the Department of Transportation in the interest of information exchange. The United States Govern- ment assumes no liability for its contents or use thereof. 5 O.’P- T*cImmc«I K fr> P»c——tt«— P /• *' 2. C t»tiw Ac<*l»i*a Mo. 1. i Ho. s.L J)OT-HS-805 320 4pr.»W rnU J. !•>••• £>•*• COST EVALUATION FOR NINE FEDERAL MOTOR VEHICLE NOVEMBER 1979 SAFETY STANDARDS Vol. VI 4. 7«Imm| CWp.. miM Cat* $. —if Of|«w itiiMi B >»•»! Mo. 7 . AvAa/a M.R. GARVEY, J. A. LESCZHIK, R.F. McLEAN *. PwMkt Ot,s>i ukM K«m m* «<»IH 10. U«.l N. (THAIS) DE L0REAN MOTOR COMPANY RESEARCH & ENGINEERING DIVISION 1 I Conflict 04 G'tni N • 2401 ELLIOTT STREET D0T-HS- 8-0201 TROY. MICHIGAN 48084 13. Tjth ol R sport ond P *r«od Cov«r*^ FINAL REPORT DEMT^rOF^^RWlON 10/78 - 11/79 NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION 400 SEVENTH STREET S.W.
    [Show full text]
  • Saf-T-Liner® C2 School Brochure
    SAF-T-LINER ® C2 BECAUSE EVERY MILE MATTERS A bus that goes beyond State-of-the-art BusWise® Technologies. Zonar® remote fleet management. The ultra-efficient DD5™ engine. These are just a few of the innovations that define the Saf-T-Liner® C2 from Thomas Built Buses. Why do we constantly challenge ourselves, pushing beyond what we thought possible, to create the most advanced and intelligent school bus innovations on the market? One word: safety. Ever since we began manufacturing school buses, safety has been our guiding star. It’s a force that drives all of us, from the engineers who designed the C2 to the technicians who build quality and care into each bus we make. Safety is the reason smart innovation is at the heart of every aspect of the C2. Our enhanced visibility gives drivers added confidence on the road. Our efficient engines reliably transport kids to and from school. Our sustainable manufacturing helps improve the safety of the environment. All in a bus that reduces the total cost of ownership, allowing school districts to offer the safest transportation possible for years to come. The C2 is built for the children of today – and the children of tomorrow. We’re driven to protect them every step of the way, because it’s children who drive the future. Designed with drivers in mind It’s a fact: the more confident and alert bus drivers feel, the more safely they drive. That’s why we designed the C2 to be the most ergonomic and intuitive driving experience possible – with enhanced visibility, driver-friendly design and state-of-the-art technology.
    [Show full text]
  • Propane Autogas School Bus Manufacturers
    PROPANE AUTOGAS SCHOOL BUS MANUFACTURERS When schools adopt propane autogas school buses, everyone — students, parents, and educators — wins. Schools can reduce fuel and maintenance costs with propane autogas buses compared with diesel, giving them the opportunity to invest those savings where it matters most — back in the classroom. Here’s a list of propane-powered school bus manufacturers. Blue Bird Corporation www.blue-bird.com Blue Bird offers a complete line of Type A, C and D school buses in a variety of options and configurations. Since 1927, Blue Bird Corporation has continued to set industry standards with its innovative design and manufacturing capabilities. Additionally, Blue Bird provides comprehensive financial solutions through Blue Bird Capital Services. Today, Blue Bird has more than 1,500 employees, Georgia-based manufacturing facilities and an extensive network of Dealers and Parts & Service facilities throughout North America. Its global presence can be seen in more than 60 countries through sales into Africa, Asia, the Caribbean, Latin America, Europe and the Middle East. Collins Bus Corporation www.collinsbuscorp.com Headquartered in Hutchinson, Kansas, Collins Industries specializes in manufacturing Type A school buses, and also manufactures ambulances and other special-purpose vehicles. The company’s Nexbus Propane model is available only on a GM chassis. It was built in conjunction with CleanFUEL USA, which was the first company to develop liquid propane fuel injection engine systems in the United States. IC Bus www.icbus.com Each vehicle built by IC Bus is backed by the power of Navistarr, a global leader in the transportation industry with more than 175 years of experience building trucks, buses, RVs, and defense vehicle.
    [Show full text]
  • Regional School Bus Study (2012)
    REGIONAL SCHOOL BUS STUDY A Comparison Of Alternative Fuels For School Transportation Fleets January 2012 SOUTH CENTRAL REGIONAL COUNCIL OF GOVERNMENTS PLANNING FOR OUR REGION'S FUTURE REGIONAL SCHOOL BUS STUDY January, 2012 Prepared By: VN Engineers, Inc. 116 Washington Avenue North Haven, CT 06473 (203) 234-7862 Prepared For: South Central Regional Council of Governments 127 Washington Avenue, 4th Floor West North Haven, CT 06473 (203) 234-7555 EXECUTIVE SUMMARY School buses are an important part of our transportation system, as they provide a safe and reliable means for many children throughout the nation to get to and from school. However, exhaust from diesel engines contains numerous pollutants that not only contribute to poor outdoor air quality, but also can leak into passenger cabins of buses, amassing in concentrations that are much higher than outdoor air. Diesel exhaust has serious health impacts for all who are exposed to it, but children are particularly susceptible to its harmful effects and disproportionately suffer from asthma, respiratory irritations, and other possible long-term conditions. The vast majority of school buses in Connecticut and the SCRCOG region are diesel-powered. However, there have been a number of recent advances in alternative fuel technology and corresponding opportunities for bus operators to benefit from the use of alternative fuel technology to reduce diesel emissions, improve air quality, limit health risks, improve efficiency, extend vehicle life, and increase energy independence. Four of the most commonly used alternative fuels have been tested and used for school bus operations. They include: biodiesel, compressed natural gas, electricity, and propane.
    [Show full text]
  • Top 10 School Bus Companies Blog
    TOP 10 SCHOOL BUS COMPANIES Throughout the years, the task of making the best buses for school transportation has been handled by various companies. This article features 10 school bus companies which made a name for themselves, when it came to redefining the way we look at a school bus. #1 WAYNE CORPORATION Topping our list of companies is Wayne Corporation. Though the company declared itself bankrupt and discontinued operation in 1992, the Wayne Corporation had played a vital role in the development of safe buses for school children. They were the first and foremost to introduce the concept of school buses for schools. Their innovation predates the famous yellow coloured buses which are widely used these days. www.trackschoolbus.com They introduced the horse drawn carts, including kid hacks, which later evolved into automobiles which used full metal body chassis. Wayne Corporation introduced guard rails on the sides of all school buses, inboard wheelchair lifts, and even high-headroom doors. They were the first with a school bus based upon a cutaway van chassis, the Wayne Busette. This chassis design is still one of the most popular in North American markets even after more than 35 years. #2 BLUE BIRD An all time giant, the Blue Bird Corporation (formerly called Blue Bird Body Company) is clearly one of the top school bus manufacturing companies even today. Blue Bird's corporate headquarters and main manufacturing facilities are in Georgia. www.trackschoolbus.com It was in 1937 that the company began production of full-steel bus bodies. This innovation would soon replace the wooden bodies which were commonly used in the United States.
    [Show full text]
  • NTSB Executive Summary
    NATIONAL TRANSPORTATION SAFETY BOARD Public Meeting of May 22, 2018 (Information subject to editing) Special Investigation Report School Bus Transportation Safety, Baltimore, Maryland, November 1, 2016, and Chattanooga, Tennessee, November 21, 2016 NTSB/SIR-18/02 This is a synopsis from the NTSB’s report and does not include the Board’s rationale for the conclusions, probable cause, and safety recommendations. NTSB staff is currently making final revisions to the report from which the attached conclusions and safety recommendations have been extracted. The final report and pertinent safety recommendation letters will be distributed to recommendation recipients as soon as possible. The attached information is subject to further review and editing to reflect changes adopted during the Board meeting. Executive Summary School bus travel is one of the safest forms of transportation in the United States. Every day, nearly 600,000 buses carry more than 25 million students to and from school and activities. Children are safer traveling in school buses than in any other vehicle. Although school buses are extremely safe, the National Transportation Safety Board (NTSB) continues to investigate school bus crashes in which fatalities and injuries occur. Improved oversight of school bus drivers and enhancements to school bus design—such as installation of passenger lap/shoulder belts, electronic stability control, and automatic emergency braking—could prevent or mitigate such crash outcomes. In November 2016, the NTSB began the investigation of two multifatality crashes involving school buses. Each crash was initiated when the driver lost control of the school bus. In the November 1 crash in Baltimore, Maryland, the driver was epileptic and suffered a seizure.
    [Show full text]
  • Saftey Data Sheet
    SAFTEY DATA SHEET Document #: SDS 011 Revision: 1 Issue Date: 6-18-2015 Page 1 of 8 ASI 502 Color (Almond, Bronze, School Bus Yellow, Trans Beige, Trans Blue, Trans Charcoal, Trans Earth, Trans Green, Trans Grey, Trans Rose, Trans White, Yellow) Section 1: Product and Company Identification American Sealants, Inc. Emergency Phone Number 3806 Option Pass Infotrac: +1-800-535-5053 (Within US) Fort Wayne, Indiana 46818 Infotrac: +1-352-323-3500 (Outside US) Phone: 260-489-0728 Fax: 260-489-0519 Product Identifier: ASI 502 Color (Almond, Bronze, School Bus Yellow, Trans Beige, Trans Blue, Trans Charcoal, Trans Earth, Trans Green, Trans Grey, Trans Rose, Trans White, Yellow) Recommended Use: Adhesive Restrictions on Use: None known Section 2: Hazard(s) Identification GHS Classification: Not a hazardous substance or mixture. Acute Effects: No information on significant adverse effects. Delayed Effects: No information on significant adverse effects. Indication of Immediate Medical Attention and Special Treatment Needed, If Needed: Treat symptomatically and supportively. GHS Label Elements Symbol(s): None. Signal Word: None. Hazard Statement(s): None known. Precautionary Statement(s) Prevention: Use only outdoors or in a well-ventilated area. Avoid release to the environment. Response: None known. Storage: Keep in properly labeled containers. Store in accordance with the particular national regulations. SAFTEY DATA SHEET Product Identifier: ASI 502 Color (Almond, Bronze, School Bus Yellow, Document #: SDS 011 Trans Beige, Trans Blue, Trans Charcoal, Trans Earth, Trans Green, Revision: 1 Trans Grey, Trans Rose, Trans White, Yellow) Disposal: Dispose of contents/container in accordance with local/regional/national/ international regulations. Section 3: Composition/Information on Ingredients CAS Component Percent 7631-86-9 Silicon dioxide 5 - <10 64742-46-7 Distillates (petroleum), hydrotreated middle 5 - <10 Section 4: First-Aid Measures Inhalation: IF INHALED: Remove to fresh air.
    [Show full text]