DOCSLIB.ORG

Sodium Hydrosulfide (Nahs) Recommended Procedures for Truck Unloading

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Sodium Hydrosulfide (Nahs) Recommended Procedures for Truck Unloading Sodium Hydrosulfide (NaHS) Recommended Procedures for Truck Unloading TDC, LLC 1916 Farmerville Hwy. Ruston LA 71270 The following presentation was designed to provide specific information on unloading trucks containing Sodium Hydrosulfide (NaHS). This presentation has been developed as a guide only. THINK SAFETY AT ALL TIMES! STAY ON TOP OF SAFE HANDLING PROCEDURES Safety is Everyone’s Business Training Requirements Personnel handling hazardous chemicals should be trained in accordance with the applicable federal and state requirements These training requirements include, but may not be limited to: • Hazard Communications - 29 CFR 1910.1200 • Personal Protective Equipment - 29 CFR 1910.132 • Respiratory Protection - 29 CFR 1910.134 • Occupational Noise Exposure - 29 CFR 1910.95 • Hazmat - 49 CFR 172.700 Shipping Requirements Sodium Hydrosulfide (NaHS) is classified as a corrosive and toxic liquid. The Proper Shipping Description is: UN2922 Corrosive liquids, toxic, n.o.s., 8(6.1), PG II (sodium hydrosulfide solution) Bulk shipments are placarded “Corrosive”. KNOW THE PRODUCT! Read the MSDS MSDS Review ¾ Sodium Hydrosulfide (NaHS) is very alkaline (pH 11.5- 12.5) and very corrosive to the skin. ¾ Solution is typically yellow to dark green with a strong hydrogen sulfide (rotten egg) odor. ¾ Solutions are 20% to 45% strength and weigh 9.6 – 10.9 ppg. ¾ The vapor space over NaHS solutions contains highly toxic hydrogen sulfide (H2S). This gas is colorless and heavier than air. The level of H2S above the solution is increased by solution contact with acidic materials, heating the solution and dilution, which lowers the pH of the solution. NaHS is manufactured by reacting Hydrogen Sulfide Gas (H2S) with Sodium Hydroxide (Caustic Soda) (NaOH). H2S + NaOH = NaHS + H2O Hydrogen Sulfide Gas + Caustic Soda = Sodium Hydrosulfide + Water Procedure EmployersEmployers shouldshould consultconsult withwith theirtheir safetysafety personnelpersonnel andand terminalterminal operatorsoperators whenwhen developingdeveloping aa detaileddetailed writtenwritten NaHSNaHS unloadingunloading procedureprocedure forfor theirtheir specificspecific location.location. Step 1: Wear the required PPE. • Hard Hat • Chemical Goggles • Full Face Shield • Chemical Suit • Chemical Protective Gloves • Chemical Protective Boots • Breathing Air/ SCBA (When opening vapor space) Step 2: Inspect the unloading area and stage the truck. Step 3: Chock the wheels. Step 4: Place the orange traffic cone. Step 5: Attach grounding cable. Step 6: Check for possible hazards. Step 7: Connect vapor recovery system. Step 8: Connect unloading hose. Step 9: Product Sampling, if required. Step 10: Set the valves for transfer of product to storage. Step 11: Begin transfer of product. Step 12: Complete liquid transfer and stop the off-loading process. Step 13: Disconnect the unloading hose. Step 14: Disconnect the vapor recovery system. Step 15: Remove the grounding cable. Step 16: Remove the wheel chocks and store in a safe location. Step 17: Check for hazards. Step 18: Remove the traffic cone and instruct driver on exiting. Step 19: Clean the unloading area if required Step 20: Remove and clean the PPE. Spills and Cleanup Small Releases • Confine and absorb small releases with sand, earth or other inert absorbent. • Oxidize the residual reactive sulfides with a weak (3-5%) hydrogen peroxide solution. Note: Normal drug store hydrogen peroxide is 3%. • If unavailable, diluted common household bleach may be substituted. Diluted peroxide and bleach minimize the potential for the release of H2S vapors. Large Releases • Wear proper protective equipment. • Confine area to qualified personnel. • Shut off release if safe to do so. • Dike spill area to prevent runoff into sewers, drains or surface waterways. • Recover as much of the solution as possible. • Treat remaining material as a small release. Hydrogen Peroxide • Commercially purchased 35% Hydrogen Peroxide must be diluted to 3–5% before it can be used to oxidize small spills. • Do not attempt to oxidize a NaHS spill with 35% Hydrogen Peroxide. • Review the 35% Hydrogen Peroxide label and MSDS before handling and diluting and wear the required Personal Protective Equipment (PPE). Diluting 35% Hydrogen Peroxide to a 3-5% Solution 1. Add approximately one-half (1/2) gallon or 1.89 liters of 35% peroxide to a clean/dry, appropriately labeled 5-gallon bucket. 2. Add approximately 4 and one-half (4 ½) gallons or 17.03 liters of water to the bucket. Wear the required PPE. Apply the diluted Hydrogen Peroxide solution to the small NaHS spill. Always wear the required Personal Protective Equipment (PPE). Hard Hat Chemical Goggles and Face Shield Protective Gloves Rain Suit/Slicker Protective Boots REMEMBER ! ! ! ! • NEVER rinse a NaHS spill into a storm drain or sewer. • Potential toxic and explosive mixtures of hydrogen sulfide gas can be created when NaHS comes in contact with acids. Emergencies Drip buckets and containment pads can be utilized for catching small spills and leaks. Note: Drip buckets should be labeled to ensure NaHS is not mixed with other chemicals. Ensure emergency showers and eyewashes are available and tested prior to each unloading operation. If Sodium Hydrosulfide comes in contact with your eyes: • Immediately flush with large quantities of water for at least 15 minutes. • Hold your eyelids apart during the irrigation to insure a thorough flushing of the entire area of the eye. • Obtain immediate medical attention. MAN DOWN ! In the event you find a coworker unconscious at the worksite and you suspect H2 S vapors are present DO NOT attempt a rescue until you have: 1. Notified other personnel, and 2. Donned breathing air (SCBA). 3. Always use the buddy system FIRE ! •Sodium Hydrosulfide Solution is non- flammable. • If exposed to heat or acids, H2 S will be released and may form explosive mixtures with the air. •If the railcar is exposed to fire, cool it with a water spray. •Remember heating may cause the release of Hydrogen Sulfide vapors. When handling, transporting, storing or distributing any hazardous chemical, please consult the manufacturer’s Material Safety Data Sheet (MSDS). Should you have any questions regarding this presentation or would like additional information on Sodium Hydrosulfide related issues, please contact TDC, LLC at (800) 422-6274. The information and recommendations contained in this presentation have been compiled from reliable sources, TDC, LLC makes no guarantee as to, and assumes no responsibility for, the correctness, sufficiency or completeness of such information or recommendations. Other or additional safety measures may be required based on your particular circumstances. .
Load more

Recommended publications
  • Inventory Size (Ml Or G) 103220 Dimethyl Sulfate 77-78-1 500 Ml
    Inventory Bottle Size Number Name CAS# (mL or g) Room # Location 103220 Dimethyl sulfate 77-78-1 500 ml 3222 A-1 Benzonitrile 100-47-0 100ml 3222 A-1 Tin(IV)chloride 1.0 M in DCM 7676-78-8 100ml 3222 A-1 103713 Acetic Anhydride 108-24-7 500ml 3222 A2 103714 Sulfuric acid, fuming 9014-95-7 500g 3222 A2 103723 Phosphorus tribromide 7789-60-8 100g 3222 A2 103724 Trifluoroacetic acid 76-05-1 100g 3222 A2 101342 Succinyl chloride 543-20-4 3222 A2 100069 Chloroacetyl chloride 79-04-9 100ml 3222 A2 10002 Chloroacetyl chloride 79-04-9 100ml 3222 A2 101134 Acetyl chloride 75-36-5 500g 3222 A2 103721 Ethyl chlorooxoacetate 4755-77-5 100g 3222 A2 100423 Titanium(IV) chloride solution 7550-45-0 100ml 3222 A2 103877 Acetic Anhydride 108-24-7 1L 3222 A3 103874 Polyphosphoric acid 8017-16-1 1kg 3222 A3 103695 Chlorosulfonic acid 7790-94-5 100g 3222 A3 103694 Chlorosulfonic acid 7790-94-5 100g 3222 A3 103880 Methanesulfonic acid 75-75-2 500ml 3222 A3 103883 Oxalyl chloride 79-37-8 100ml 3222 A3 103889 Thiodiglycolic acid 123-93-3 500g 3222 A3 103888 Tetrafluoroboric acid 50% 16872-11-0 1L 3222 A3 103886 Tetrafluoroboric acid 50% 16872-11-0 1L 3222 A3 102969 sulfuric acid 7664-93-9 500 mL 2428 A7 102970 hydrochloric acid (37%) 7647-01-0 500 mL 2428 A7 102971 hydrochloric acid (37%) 7647-01-0 500 mL 2428 A7 102973 formic acid (88%) 64-18-6 500 mL 2428 A7 102974 hydrofloric acid (49%) 7664-39-3 500 mL 2428 A7 103320 Ammonium Hydroxide conc.
    [Show full text]
  • Sodium Hydrosulfide
    SAFETY DATA SHEET 1. Identification Product identifier Sodium Hydrosulfide Solution Other means of identification Product number GENLP-TDC-001-CAN Recommended use Product is a unique alkaline material, playing a vital role in many industrial processes. Recommended restrictions Use in accordance with supplier's recommendations. Manufacturer/Importer/Supplier/Distributor information Importer TDC Energy Canada, LTD. Address 1916 Farmerville Hwy Ruston, LA 71270 Telephone Customer Service (800) 422-6274 Email [email protected] CHEMTREC: 800-424-9300 (Domestic – North America) CHEMTREC: +1-703-527-3887 (International) 2. Hazard identification Physical hazards Corrosive to metals Category 1 Health hazards Acute toxicity, oral Category 3 Skin corrosion/irritation Category 1B Serious eye damage/eye irritation Category 1 Environmental hazards Hazardous to the aquatic environment, acute Category 1 hazard Label elements Signal word Danger Hazard statement May be corrosive to metals. Toxic if swallowed. Causes severe skin burns and eye damage. Very toxic to aquatic life. Precautionary statement Prevention Keep only in original container. Do not breathe mist or vapour. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Avoid release to the environment. Wear protective gloves/protective clothing/eye protection/face protection. Response If swallowed: Immediately call a poison centre/doctor. Rinse mouth. Do NOT induce vomiting. If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. Wash contaminated clothing before reuse. If inhaled: Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
    [Show full text]
  • Nahs Technical Guide
    TECHNICAL GUIDE FOR SOLUTIONS OF SODIUM HYDROSULFIDE TECHNICAL GUIDE FOR SOLUTIONS OF SODIUM HYDROSULFIDE TABLE OF CONTENTS TOPIC PAGE Overview 1 Health Hazards and First Aid 2 Flammability and Fire Response / Storage 3 Handling (PPE) 4 Equipment Transfers/Recommendations 5 Shipping 13 Releases 14 APPENDIX This Page Intentionally left Blank Appendix A H2S Monitors Appendix B Hydrogen Sulfide Toxicity Chart Appendix C Density, Boiling and Freezing Points of Appendix D Sodium Hydrosulfide Viscosity of Typical 45% Sodium Appendix E Hydrosulfide Solution Sodium Hydrosulfide Site Assessment Appendix F Checklist TECHNICAL GUIDE FOR SOLUTIONS OF SODIUM HYDROSULFIDE Overview Sodium Hydrosulfide, chemical formula NaHS, is a highly alkaline salt solution with a pH of 11.5 to 12.5. The solution is typically yellow to dark green and has a rotten-egg odor due to the Hydrogen Sulfide (H2S) content. The product strength ranges from 20% to 45% by weight and weighs 9 to 11 pounds per gallon (specific gravity from 1.13 to 1.30 g/cm3). Solutions of NaHS are considered stable in normal transportation. The vapor space over NaHS solutions contains highly toxic Hydrogen Sulfide gas. The Hydrogen Sulfide gas is colorless and it is heavier than air. It will remain close to the ground and collect in low lying areas. The amount of Hydrogen Sulfide gas evolved from NaHS solutions is noticeably increased when the pH of the solution is below the pH of 10.2. This happens when the solution comes into contact with acidic materials or other materials that have a pH lower than 10.2. Dilution of the material will also create a minimal amount of Hydrogen Sulfide gas due to the lower pH of water coming in contact with the solution.
    [Show full text]
  • SAFETY DATA SHEET Sodium Hydrosulfide Solution
    SAFETY DATA SHEET Sodium Hydrosulfide Solution Section 1. Identification Product name : Sodium Hydrosulfide Solution Synonyms : NaHS, sodium hydrogen sulfide, sodium bisulfide, sodium mercaptan Relevant identified uses of the substance or mixture and uses advised against Product use : Industrial Manufacturer : HollyFrontier Refining & Marketing LLC 2828 North Harwood Suite 1300 Dallas, Texas 75201 USA Customer Service: (888) 286-8836 Emergency telephone : CHEMTREC® (800) 424-9300 number CCN 201319 Section 2. Hazards identification OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200). Classification of the : CORROSIVE TO METALS - Category 1 substance or mixture ACUTE TOXICITY (oral) - Category 4 SKIN CORROSION - Category 1 SERIOUS EYE DAMAGE - Category 1 GHS label elements Hazard pictograms : Signal word : Danger Hazard statements : May be corrosive to metals. Harmful if swallowed. Causes severe skin burns and eye damage. Precautionary statements Prevention : Wear protective gloves. Wear eye or face protection. Wear protective clothing. Keep only in original container. Do not eat, drink or smoke when using this product. Wash hands thoroughly after handling. Response : Absorb spillage to prevent material damage. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician. IF SWALLOWED: Immediately call a POISON CENTER or physician. Rinse mouth. Do NOT induce vomiting. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. Wash contaminated clothing before reuse. Immediately call a POISON CENTER or physician. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
    [Show full text]
  • Technical Guide for Solutions of Sodium Hydrosulfide Technical Guide for Solutions of Sodium Hydrosulfide
    TECHNICAL GUIDE FOR SOLUTIONS OF SODIUM HYDROSULFIDE TECHNICAL GUIDE FOR SOLUTIONS OF SODIUM HYDROSULFIDE TABLE OF CONTENTS TOPIC PAGE Overview 1 Health Hazards and First Aid 2 Flammability and Fire Response / Storage 3 Handling (PPE) 4 Equipment Recommendations / Transfers 5 Shipping 13 Releases 14 APPENDIX Material Safety Data Sheet 16 H2S Monitors 23 Hydrogen Sulfide Toxicity Chart 26 Density, Boiling and Freezing Points of 28 Sodium Hydrosulfide Viscosity of Typical 45% Sodium 30 Hydrosulfide Solution Sodium Hydrosulfide Site Assessment 32 Checklist TECHNICAL GUIDE FOR SOLUTIONS OF SODIUM HYDROSULFIDE Overview Sodium Hydrosulfide, chemical formula NaHS, is a highly alkaline salt solution with a pH of 11.5 to 12.5. The solution is typically yellow to dark green and has a rotten-egg odor due to the Hydrogen Sulfide (H2S) content. The product strength ranges from 20% to 45% by weight and weighs 9 to 11 pounds per gallon (specific gravity from 1.13 to 1.30 g/cm3). Solutions of NaHS are considered stable in normal transportation. The vapor space over NaHS solutions contains highly toxic Hydrogen Sulfide gas. The Hydrogen Sulfide gas is colorless and it is heavier than air. It will remain close to the ground and collect in low lying areas. The amount of Hydrogen Sulfide gas evolved from NaHS solutions is noticeably increased when the pH of the solution is below the pH of 10.2. This hap pens when the solution comes into contact with acidic materials or other materials that have a pH lower than 10.2. Dilution of the material will also create a minimal amount of Hydrogen Sulfide gas due to the lower pH of water coming in contact with the solution.
    [Show full text]
  • Sodium Hydrogen Sulfide
    Product Safety Summary Sodium Hydrogen Sulfide, Solid (70-72% with Crystallization Waters < 25%) CAS No. 16721-80-5 This Product Safety Summary is intended to provide a general overview of the chemical substance. The information on the summary is basic information and is not intended to provide emergency response information, medical information or treatment information. The summary should not be used to provide in-depth safety and health information. In-depth safety and health information can be found on the Safety Data Sheet (SDS) for the chemical substance. Names Sodium hydrogen sulfide (sulphide) Sodium hydrosulfide (hydrosulphide) Sodium mercaptan Sodium sulfhydrate Sodium bisulfide Sodium mercaptide Product Overview Solvay Fluorides, LLC does not sell sodium hydrogen sulfide directly to consumers. Consumers are unlikely to be exposed to sodium hydrogen sulfide in any of the consumer product applications listed below and only where the sodium hydrogen sulfide is not transformed or reacted. Sodium hydrogen sulfide is a yellow, solid flake with a sulfurous (rotten egg) smell. It is used in water treatment, the pulp and paper industry, and in leather processing as a tanning agent or hair remover (from hides). Sodium hydrogen sulfide may be used in the making of colors and dyes. It can also be used in the manufacture of other chemicals, metals or in ore processing (mining) and in waste water, soil and process sludge treatment. Exposure to sodium hydrogen sulfide can cause severe irritation to the skin, eyes, and respiratory tract. Sodium hydrogen sulfide may cause sensitization (develop an allergic reaction). Breathing sodium hydrogen sulfide dusts may aggravate asthma or other pulmonary (breathing) diseases and may cause headaches, dizziness, nausea and vomiting.
    [Show full text]
  • List of Reactive Chemicals
    LIST OF REACTIVE CHEMICALS Chemical Prefix Chemical Name Reactive Reactive Reactive CAS# Chemical Chemical Chemical Stimulus 1 Stimulus 2 Stimulus 3 111-90-0 "CARBITOL" SOLVENT D 111-15-9 "CELLOSOLVE" ACETATE D 110-80-5 "CELLOSOLVE" SOLVENT D 2- (2,4,6-TRINITROPHENYL)ETHYL ACETATE (1% IN ACETONE & BENZENE S 12427-38-2 AAMANGAN W 88-85-7 AATOX S 40487-42-1 AC 92553 S 105-57-7 ACETAL D 75-07-0 ACETALDEHYDE D 105-57-7 ACETALDEHYDE, DIETHYL ACETAL D 108-05-4 ACETIC ACID ETHENYL ESTER D 108-05-4 ACETIC ACID VINYL ESTER D 75-07-0 ACETIC ALDEHYDE D 101-25-7 ACETO DNPT T 126-84-1 ACETONE DIETHYL ACETAL D 108-05-4 ACETOXYETHYLENE D 108-05-4 1- ACETOXYETHYLENE D 37187-22-7 ACETYL ACETONE PEROXIDE, <=32% AS A PASTE T 37187-22-7 ACETYL ACETONE PEROXIDE, <=42% T 37187-22-7 ACETYL ACETONE PEROXIDE, >42% T S 644-31-5 ACETYL BENZOYL PEROXIDE (SOLID OR MORE THAN 45% IN SOLUTION) T S 644-31-5 ACETYL BENZOYL PEROXIDE, <=45% T 506-96-7 ACETYL BROMIDE W 75-36-5 ACETYL CHLORIDE W ACETYL CYCLOHEXANE SULFONYL PEROXIDE (>82% WITH <12% WATER) T S 3179-56-4 ACETYL CYCLOHEXANE SULFONYL PEROXIDE, <=32% T 3179-56-4 ACETYL CYCLOHEXANE SULFONYL PEROXIDE, <=82% T 674-82-8 ACETYL KETENE (POISON INHALATION HAZARD) D 110-22-5 ACETYL PEROXIDE, <=27% T 110-22-5 ACETYL PEROXIDE, SOLID, OR MORE THAN 27% IN SOLUTION T S 927-86-6 ACETYLCHOLINE PERCHLORATE O S 74-86-2 ACETYLENE D 74-86-2 ACETYLENE (LIQUID) D ACETYLENE SILVER NITRATE D 107-02-08 ACRALDEHYDE (POISON INHALATION HAZARD) D 79-10-7 ACROLEIC ACID D 107-02-08 ACROLEIN, INHIBITED (POISON INHALATION HAZARD) D 107-02-08 ACRYLALDEHYDE (POISON INHALATION HAZARD) D 79-10-7 ACRYLIC ACID D 141-32-2 ACRYLIC ACID BUTYL ESTER D 140-88-5 ACRYLIC ACID ETHYL ESTER D 96-33-3 ACRYLIC ACID METHYL ESTER D Stimulus - Stimuli is the thermal, physical or chemical input needed to induce a hazardous reaction.
    [Show full text]
  • Safety Data Sheet
    SAFETY DATA SHEET 1. Identification Product identifier Sodium sulfhydrate Other means of identification Item NG-I5820 Recommended use For Laboratory Use Only Recommended restrictions None known. Manufacturer/Importer/Supplier/Distributor information Manufacturer Company name Chem Service, Inc. Address 660 Tower Lane West Chester, PA 19380 United States Telephone Toll Free 800-452-9994 Direct 610-692-3026 Website www.chemservice.com E-mail [email protected] Emergency phone number Chemtrec US 800-424-9300 Chemtrec outside US +1 703-527-3887 2. Hazard(s) identification Physical hazards Self-heating substances and mixtures Category 1 Corrosive to metals Category 1 Health hazards Acute toxicity, oral Category 3 Skin corrosion/irritation Category 1 Serious eye damage/eye irritation Category 1 Specific target organ toxicity, single exposure Category 3 respiratory tract irritation Environmental hazards Not classified. OSHA defined hazards Not classified. Label elements Signal word Danger Hazard statement Self-heating; may catch fire. May be corrosive to metals. Toxic if swallowed. Causes severe skin burns and eye damage. Causes serious eye damage. May cause respiratory irritation. Precautionary statement Prevention Keep only in original container. Keep cool. Protect from sunlight. Avoid breathing dust/fume/gas/mist/vapors/spray. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Use only outdoors or in a well-ventilated area. Wear eye protection/face protection. Wear protective gloves/protective clothing/eye protection/face protection. Response If swallowed: Immediately call a poison center/doctor. If swallowed: Rinse mouth. Do NOT induce vomiting. If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
    [Show full text]
  • Title of Thesis Or Dissertation, Worded
    DEVELOPMENT OF CHEMICAL TOOLS FOR STUDYING REACTIVE SULFUR SPECIES by MATTHEW MICHAEL CERDA A DISSERTATION Presented to the Department of Chemistry and Biochemistry and the Graduate School of the University of Oregon in partial fulfillment of the requirements for the degree of Doctor of Philosophy June 2020 DISSERTATION APPROVAL PAGE Student: Matthew Michael Cerda Title: Development of Chemical Tools for Studying Reactive Sulfur Species This dissertation has been accepted and approved in partial fulfillment of the requirements for the Doctor of Philosophy degree in the Department of Chemistry and Biochemistry by: Michael M. Haley Chairperson Michael D. Pluth Advisor Darren W. Johnson Core Member Raghuveer Parthasarathy Institutional Representative and Kate Mondloch Interim Vice Provost and Dean of the Graduate School Original approval signatures are on file with the University of Oregon Graduate School. Degree awarded June 2020 ii © 2020 Matthew Michael Cerda This work is licensed under a Creative Commons Attribution-NonCommerical-NoDerivs (United States) License. iii DISSERTATION ABSTRACT Matthew Michael Cerda Doctor of Philosophy Department of Chemistry and Biochemistry June 2020 Title: Development of Chemical Tools for Studying Reactive Sulfur Species Hydrogen sulfide (H2S) has recently emerged as an important biological signaling molecule involved in a number of key physiological processes. These observations have generated interest in harnessing H2S as a potential therapeutic agent to treat disease states and chronic conditions associated with H2S-based signaling. A mechanistic analysis of these physiological processes reveals the prevalence of H2S and other reactive sulfur species including sulfane sulfur and persulfides. To better understand the biological properties of these reactive sulfur species, chemical tools which provide methods of generating these fleeting species under controlled reaction conditions are needed.
    [Show full text]
  • Sodium Hydrosulfide Solution
    SAFETY DATA SHEET 1. Identification Product identifier Sodium Hydrosulfide Solution Other means of identification Product number GENLP-TDC-001 Recommended use Product is a unique alkaline material, playing a vital role in many industrial processes. Recommended restrictions Use in accordance with supplier's recommendations. Manufacturer/Importer/Supplier/Distributor information Manufacturer TDC, L.L.C. and TDC Services, LLC Address 1916 Farmerville Hwy Ruston, LA 71270 Telephone Customer Service (800) 422-6274 Email [email protected] CHEMTREC: 800-424-9300 (Domestic – North America) CHEMTREC: +1-703-527-3887 (International) 2. Hazard(s) identification Physical hazards Corrosive to metals Category 1 Health hazards Acute toxicity, oral Category 3 Skin corrosion/irritation Category 1B Serious eye damage/eye irritation Category 1 Environmental hazards Hazardous to the aquatic environment, acute Category 1 hazard OSHA defined hazards Not classified. Label elements Signal word Danger Hazard statement May be corrosive to metals. Toxic if swallowed. Causes severe skin burns and eye damage. Very toxic to aquatic life. Precautionary statement Prevention Keep only in original container. Do not breathe mist or vapor. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Avoid release to the environment. Wear protective gloves/protective clothing/eye protection/face protection. Response If swallowed: Immediately call a poison center/doctor. Rinse mouth. Do NOT induce vomiting. If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. Wash contaminated clothing before reuse. If inhaled: Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse cautiously with water for several minutes.
    [Show full text]
  • Redox Pty Ltd 2 Swettenham Road +61-2-97333000 Minto NSW 2566 Australia
    Safety Data Sheet Sodium hydrosulfide (70%) Revision 4, Date 10 Jan 2019 1. IDENTIFICATION Product Name Sodium hydrosulfide (70%) Other Names Sodium bisulfide; Sodium hydrogen sulfide; Sodium hydrogensulphide; Sodium hydrosulphide (solid/flake 70~72%); Sodium mercaptan Uses Leather treatment; dye and lubricant manufacture; wastewater treatment; metals finishing; ore beneficiation; pharmaceuticals. Chemical Family No Data Available Chemical Formula NaHS Chemical Name Sodium sulfide (Na(SH)) Product Description Sodium hydrosulphide with not less than 25% water of crystallization. Contact Details of the Supplier of this Safety Data Sheet Organisation Location Telephone Redox Pty Ltd 2 Swettenham Road +61-2-97333000 Minto NSW 2566 Australia Redox Pty Ltd 11 Mayo Road +64-9-2506222 Wiri Auckland 2104 New Zealand Redox Inc. 3960 Paramount Boulevard +1-424-675-3200 Suite 107 Lakewood CA 90712 USA Redox Chemicals Sdn Bhd Level 2, No. 8, Jalan Sapir 33/7 +60-3-5614-2111 Seksyen 33, Shah Alam Premier Industrial Park 40400 Shah Alam Sengalor, Malaysia Emergency Contact Details For emergencies only; DO NOT contact these companies for general product advice. Organisation Location Telephone Poisons Information Centre Westmead NSW 1800-251525 131126 Chemcall Australia 1800-127406 +64-4-9179888 Chemcall Malaysia +64-4-9179888 Chemcall New Zealand 0800-243622 +64-4-9179888 National Poisons Centre New Zealand 0800-764766 CHEMTREC USA & Canada 1-800-424-9300 CN723420 +1-703-527-3887 2. HAZARD IDENTIFICATION Poisons Schedule (Aust) Not Scheduled Globally
    [Show full text]
  • Plant Secondary Metabolite Biosynthesis and Transcriptional Regulation in Response to Biotic and Abiotic Stress Conditions
    agronomy Review Plant Secondary Metabolite Biosynthesis and Transcriptional Regulation in Response to Biotic and Abiotic Stress Conditions Rahmatullah Jan 1,2,† , Sajjad Asaf 3,† , Muhammad Numan 4, Lubna 5 and Kyung-Min Kim 1,2,* 1 Division of Plant Biosciences, School of Applied Biosciences, College of Agriculture & Life Science, Kyungpook National University, Daegu 41566, Korea; [email protected] 2 Costal Agriculture Research Institute, Kyungpook National University, Daegu 41566, Korea 3 Natural and Medical Science Research Center, University of Nizwa, Nizwa 616, Oman; [email protected] 4 Laboratory of Molecular Biology and Biotechnology, Department of Biology, University of North Carolina at Greensboro, Greensboro, NC 27412, USA; [email protected] 5 Department of Botany, Garden Campus, Abdul Wali Khan University, Mardan 23200, Pakistan; [email protected] * Correspondence: [email protected] † These authors contribute equally to this manuscript. Abstract: Plant secondary metabolites (SMs) play important roles in plant survival and in creating ecological connections between other species. In addition to providing a variety of valuable natural products, secondary metabolites help protect plants against pathogenic attacks and environmental stresses. Given their sessile nature, plants must protect themselves from such situations through ac- cumulation of these bioactive compounds. Indeed, secondary metabolites act as herbivore deterrents, barriers against pathogen invasion, and mitigators of oxidative stress. The accumulation of SMs Citation: Jan, R.; Asaf, S.; Numan, are highly dependent on environmental factors such as light, temperature, soil water, soil fertility, M.; Lubna; Kim, K.-M. Plant and salinity. For most plants, a change in an individual environmental factor can alter the content Secondary Metabolite Biosynthesis of secondary metabolites even if other factors remain constant.
    [Show full text]