DOCSLIB.ORG

Outside Telephone Cable Filled Core

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Outside Telephone Cable Filled Core Outside Telephone Cable Filled Core. Moisture Barrier. Description Soft copper wires insulated with high density polyethylene, foam skin or solid. Filled core, conformed by groups of pairs or by unit of groups of pairs. Aluminum shield and external jacket in polyethylene type moisture barrier. Construction Conductor Soft copper wires Insulation Foam skin or solid high density polyethylene. Twisted Pairs Insulated conductors are twisted into pairs Core Assembly Up to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs, from 400 pairs and more, units of 100 pairs (each unit is conformed by 4 groups of 25 pairs) Spare pairs One spare pair white-red colored at the interstices of each 100 pairs unit, to guarantee nominal numbers of pairs. Identification Pairs, groups and units that conform the core, are identified by color code (Attached) Core Wrap Non-hygroscopic dielectric tape. Offers dielectric strength between core and sheath Shield Corrugated Aluminum tape both sides covered with copolymer Jacket Black polyethylene, abrasion, weather, and penetration to water resistant 7 Moisture Barrier Filled Core with elastomeric compound, aluminum tape both sides covered with copolymer and polyethylene external jacket, firmly bonded to external side of aluminum tape Options Manufacturing according to REA and/or Bellcore specifications Shield in Flat Aluminum tape. Armor in corrugated and copolymer covered Steel tape for direct buried and for rodent protection. Galvanized steel wires armor for vertical installations. Other Core Assemblies are available upon request. Applications Trunk cable and distribution cable networks. Special for wet locations; the elastomeric compound filler prevents the entrance of moisture to the core. Installation in ducts or raceways; for buried direct in locations without heavy traffic. CENTELSA Outside Telephone Cable, are able for voice and data transmission up to 6.3 MHz, optimizing the bandwidth of copper cables. Standards and Specifications CENTELSA Outside Telephone Cable, are manufactured under the following standards: ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefin insulated copper conductor. ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor. NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry. Certifications CENTELSA Outside Telephone Cable, are certified by: ICONTEC (Colombia). Norma NTC 2061. Note: Other configurations, sizes, colors and length not specified herein are available upon request. 8 Outside Telephone Cable. Filled Core. Moisture Barrier. Foamed-Skin polyethylene insulation. Standards: ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefin insulated copper conductor. NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry. NOMINAL SPARE CONDUCTOR INSULATION JACKET OVERALL APPROX. STANDARD PAIRS PAIRS DIAMETER THICKNESS THICKNESS DIAMETER TOTAL LENGTH (mm) (mm) (mm) (mm) WEIGTH BY REEL (kg/km) (m) 10 - 0.40 0.18 1.40 9.75 94 1500 20 - 0.40 0.18 1.40 11.56 141 1500 30 - 0.40 0.18 1.40 12.96 187 1500 40 - 0.40 0.18 1.40 14.13 231 1500 50 - 0.40 0.18 1.40 15.17 275 1500 70 - 0.40 0.18 1.40 16.96 356 1500 100 1 0.40 0.18 1.40 19.30 479 1000 150 2 0.40 0.18 1.60 22.87 692 1000 200 2 0.40 0.18 1.60 25.48 886 1000 300 3 0.40 0.18 1.60 29.91 1270 750 400 4 0.40 0.18 1.80 34.06 1668 500 500 5 0.40 0.18 1.80 37.35 2044 500 600 6 0.40 0.18 1.80 40.32 2419 500 900 9 0.40 0.18 2.00 48.48 3565 350 1200 12 0.40 0.18 2.20 55.32 4699 300 1500 15 0.40 0.18 2.40 61.43 5837 250 1800 18 0.40 0.18 2.40 66.73 6941 250 2400 24 0.40 0.18 2.40 75.88 9126 250 10 - 0.50 0.20 1.40 10.67 120 1500 20 - 0.50 0.20 1.40 12.86 188 1500 30 - 0.50 0.20 1.40 14.55 252 1500 40 - 0.50 0.20 1.40 15.97 316 1500 50 - 0.50 0.20 1.40 17.23 378 1500 70 - 0.50 0.20 1.40 19.40 498 1500 100 1 0.50 0.20 1.40 22.22 682 1000 150 2 0.50 0.20 1.60 26.46 996 1000 200 2 0.50 0.20 1.60 29.62 1283 1000 300 3 0.50 0.20 1.80 35.40 1876 750 400 4 0.50 0.20 1.80 39.92 2446 500 500 5 0.50 0.20 2.00 44.39 3037 500 600 6 0.50 0.20 2.00 47.99 3606 500 900 9 0.50 0.20 2.20 57.64 5312 350 1200 12 0.50 0.20 2.40 66.03 7018 300 1500 15 0.50 0.20 2.40 72.92 8684 250 1800 18 0.50 0.20 2.60 79.57 10386 250 2400 24 0.50 0.20 2.60 90.63 13682 250 10 - 0.60 0.26 1.40 12.08 158 1500 20 - 0.60 0.26 1.40 14.86 257 1500 30 - 0.60 0.26 1.40 17.00 350 1500 40 - 0.60 0.26 1.40 18.80 442 1500 50 - 0.60 0.26 1.40 20.38 531 1500 70 - 0.60 0.26 1.60 23.55 724 1500 100 1 0.60 0.26 1.60 27.13 994 1000 150 2 0.60 0.26 1.80 32.38 1452 1000 200 2 0.60 0.26 1.80 36.39 1880 1000 300 3 0.60 0.26 1.80 43.25 2732 750 400 4 0.60 0.26 2.00 49.38 3605 500 500 5 0.60 0.26 2.20 54.80 4475 500 600 6 0.60 0.26 2.20 59.35 5309 500 900 9 0.60 0.26 2.40 71.67 7848 350 1200 12 0.60 0.26 2.60 81.99 10374 300 1500 15 0.60 0.26 2.60 90.72 12846 250 1800 18 0.60 0.26 2.80 99.02 15371 250 2400 24 0.60 0.26 2.80 113.03 20280 250 Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances. 9 Outside Telephone Cable. Filled Core. Moisture Barrier. Solid polyethylene insulation. Standards: ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefin insulated copper conductor. NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry. NOMINAL SPARE CONDUCTOR INSULATION JACKET OVERALL APPROX. STANDARD PAIRS PAIRS DIAMETER THICKNESS THICKNESS DIAMETER TOTAL LENGTH (mm) (mm) (mm) (mm) WEIGTH BY REEL (kg/km) (m) 10 - 0.40 0.23 1.40 10.34 106 1500 20 - 0.40 0.23 1.40 12.40 160 1500 30 - 0.40 0.23 1.40 13.98 211 1500 40 - 0.40 0.23 1.40 15.32 262 1500 50 - 0.40 0.23 1.40 16.49 311 1500 70 - 0.40 0.23 1.40 18.53 405 1500 100 1 0.40 0.23 1.40 21.18 548 1000 150 2 0.40 0.23 1.60 25.18 792 1000 200 2 0.40 0.23 1.60 28.15 1015 1000 300 3 0.40 0.23 1.80 33.59 1476 750 400 4 0.40 0.23 1.80 37.83 1913 500 500 5 0.40 0.23 2.00 42.05 2377 500 600 6 0.40 0.23 2.00 45.43 2812 500 900 9 0.40 0.23 2.20 54.51 4128 350 1200 12 0.40 0.23 2.40 62.26 5440 300 1500 15 0.40 0.23 2.40 68.88 6714 250 1800 18 0.40 0.23 2.60 75.13 8026 250 2400 24 0.40 0.23 2.60 85.52 10547 250 10 - 0.50 0.30 1.40 11.83 142 1500 20 - 0.50 0.30 1.40 14.51 224 1500 30 - 0.50 0.30 1.40 16.57 306 1500 40 - 0.50 0.30 1.40 18.30 384 1500 50 - 0.50 0.30 1.40 19.83 459 1500 70 - 0.50 0.30 1.60 22.90 620 1500 100 1 0.50 0.30 1.60 26.34 850 1000 150 2 0.50 0.30 1.80 31.42 1232 1000 200 2 0.50 0.30 1.80 35.27 1590 1000 300 3 0.50 0.30 1.80 41.88 2300 750 400 4 0.50 0.30 2.00 47.81 3033 500 500 5 0.50 0.30 2.20 53.04 3762 500 600 6 0.50 0.30 2.20 57.42 4454 500 900 9 0.50 0.30 2.40 69.31 6561 350 1200 12 0.50 0.30 2.60 79.26 8663 300 1500 15 0.50 0.30 2.60 87.67 10713 250 1800 18 0.50 0.30 2.80 95.68 12813 250 2400 24 0.50 0.30 2.80 109.18 16877 250 10 - 0.60 0.35 1.40 13.13 177 1500 20 - 0.60 0.35 1.40 16.35 294 1500 30 - 0.60 0.35 1.40 18.82 407 1500 40 - 0.60 0.35 1.40 20.90 514 1500 50 - 0.60 0.35 1.40 22.74 624 1500 70 - 0.60 0.35 1.60 26.33 849 1500 100 1 0.60 0.35 1.60 30.47 1168 1000 150 2 0.60 0.35 1.80 36.49 1710 1000 200 2 0.60 0.35 1.80 41.11 2215 1000 300 3 0.60 0.35 2.00 49.45 3262 750 400 4 0.60 0.35 2.20 56.44 4292 500 500 5 0.60 0.35 2.40 62.83 5324 500 600 6 0.60 0.35 2.40 68.10 6320 500 900 9 0.60 0.35 2.60 82.11 9325 350 1200 12 0.60 0.35 2.60 93.57 12270 300 1500 15 0.60 0.35 2.80 104.08 15260 250 1800 18 0.60 0.35 2.80 113.20 18183 250 2400 24 0.60 0.35 3.00 129.82 24082 250 Note: 1.
Load more

Recommended publications
  • The Twisted-Pair Telephone Transmission Line
    High Frequency Design From November 2002 High Frequency Electronics Copyright © 2002, Summit Technical Media, LLC TRANSMISSION LINES The Twisted-Pair Telephone Transmission Line By Richard LAO Sumida America Technologies elephone line is a This article reviews the prin- balanced twisted- ciples of operation and Tpair transmission measurement methods for line, and like any electro- twisted pair (balanced) magnetic transmission transmission lines common- line, its characteristic ly used for xDSL and ether- impedance Z0 can be cal- net computer networking culated from manufactur- ers’ data and measured on an instrument such as the Agilent 4395A (formerly Hewlett-Packard HP4395A) net- Figure 1. Lumped element model of a trans- work analyzer. For lowest bit-error-rate mission line. (BER), central office and customer premise equipment should have analog front-end cir- cuitry that matches the telephone line • Category 3: BWMAX <16 MHz. Intended for impedance. This article contains a brief math- older networks and telephone systems in ematical derivation and and a computer pro- which performance over frequency is not gram to generate a graph of characteristic especially important. Used for voice, digital impedance as a function of frequency. voice, older ethernet 10Base-T and commer- Twisted-pair line for telephone and LAN cial customer premise wiring. The market applications is typically fashioned from #24 currently favors CAT5 installations instead. AWG or #26 AWG stranded copper wire and • Category 4: BWMAX <20 MHz. Not much will be in one of several “categories.” The used. Similar to CAT5 with only one-fifth Electronic Industries Association (EIA) and the bandwidth. the Telecommunications Industry Association • Category 5: BWMAX <100 MHz.
    [Show full text]
  • Catv Cabling System
    NYULMC AMBULATORY CARE CENTER – FIT-OUT PHASE 1 Perkins & Will Architects PC 222 E 41st ST, NYC Project: 032698.000 Issued for GMP March 15, 2017 SECTION 27 41 33 CATV CABLING PART 1 - GENERAL 1.1 SYSTEM DESCRIPTION A. Furnish and install a complete and fully operational Television Signal Distribution System capable of delivering up to 158 video channels (6 MHz NTSC Channels containing NTSC, ATSC and QAM modulated programs) and IP Video over an installed Category 6A unshielded twisted pair cable system. The System shall utilize a cable plant comprised of a TIA/EIA 568 compliant horizontal distribution cable system and a coaxial and/or single mode fiber backbone system. The System shall employ Active Automatic Gain Control Electronics to adjust the video signal levels to each TV and shall be capable of supporting up to 14,000 connected devices. The System shall support bi-directional RF transmission for backbone interconnections. Include amplifiers, power supplies, cables, outlets, attenuators, hubs, baluns, adaptors, transceivers, and other parts necessary for the reception and distribution of the local CATV signals. Back-feed existing campus system. (CAT 5e is acceptable to 117 channels) B. Distribute cable channels to TV outlets to permit simple connection of EIA standard Analog/Digital television receivers. C. Deliver at outlets monochrome and NTSC color television signals without introducing noticeable effect on picture and color fidelity or sound. Signal levels and performance shall meet or exceed the minimums specified in Part 76 of the FCC Rules and Regulations D. Provide reception quality at each outlet equal to or better than that received in the area with individual antennas.
    [Show full text]
  • HD Television on Cat 5/6 Cable Cable TV on Cat 5/6 Cable
    HD Television on Cat 5/6 Cable Cable TV on Cat 5/6 Cable Innovative Technology .... Exceptional Quality! The Lynx® Television Network Distributes up to 640 digital Increases flexibility for moves, adds channels on Cat 5 or Cat 6 cable and changes Excellent for cable TV, SMATV, or Improves reliability off-air television distribution Creates a technology bridge to Simplifies cabling requirements Internet TV and IPTV The Lynx Television Network simultaneously simplifies installation, standardizes the wiring, delivers up to 210 HDTV channels, 640 and reduces maintenance requirements. standard digital channels, or 134 analog channels on Cat 5 or Cat 6 cable. Frequency The Lynx Network increases system flexibility capabilities are 5 MHz to 860 MHz. because moves, adds, and changes are easy with Cat5/6 cable. A Lynx hub in the wiring closet converts an unbalanced coaxial signal into eight or A homerun wiring design improves reliability sixteen balanced signals transmitted on because there are no taps or splitters between twisted pair cables. At the point of use a the distribution hub and the TV. wallplate F or single port converter changes the signal back to coaxial form. The Lynx Network also provides a “technology bridge” to Internet TV and IPTV by setting up the cabling that these technologies use. A patented RF balun is the centerpiece of the Lynx design. A pair of send / receive baluns delivers a clean RF signal to each TV (on pair four). The baluns use an RF technology that delivers HD, digital, and analog channels on network cables without using any bandwidth Wallplate F Single port converter on the network itself.
    [Show full text]
  • Introduction to Digital Subscriber's Line (DSL) Chapter 2 Telephone
    Introduction to Digital Subscriber’s Line (DSL) Professor Fu Li, Ph.D., P.E. © Chapter 2 Telephone Infrastructure · Telephone line dates back to Bell in 1875 · Digital Transmission technology using complex algorithm based on DSP and VLSI to compensate impairments common to phone lines. · Phone line carries the single voice signal with 3.4 KHz bandwidth, DSL conveys 100 Compressed voice signals or a video signals. 1 · 15% phones require upgrade activities. · Phone company spent approximately 1 trillion US dollars to construct lines; · 700 millions are in service in 1997, 900 millions by 2001. · Most lines will support 1 Mb/s for DSL and many will support well above 1Mb/s data rate. Typical Voice Network 2 THE ACCESS NETWORK • DSL is really an access technology, and the associated DSL equipment is deployed in the local access network. • The access network consists of the local loops and associated equipment that connects the service user location to the central office. • This network typically consists of cable bundles carrying thousands of twisted-wire pairs to feeder distribution interfaces (FDIs). Two primary ways traditionally to deal with long loops: • 1.Use loading coils to modify the electrical characteristics of the local loop, allowing better quality voice-frequency transmission over extended distances (typically greater than 18,000 feet). • Loading coils are not compatible with the higher frequency attributes of DSL transmissions and they must be removed before DSL-based services can be provisioned. 3 Two primary ways traditionally to deal with long loops • 2. Set up remote terminals where the signals could be terminated at an intermediate point, aggregated and backhauled to the central office.
    [Show full text]
  • Digital Subscriber Lines and Cable Modems Digital Subscriber Lines and Cable Modems
    Digital Subscriber Lines and Cable Modems Digital Subscriber Lines and Cable Modems Paul Sabatino, [email protected] This paper details the impact of new advances in residential broadband networking, including ADSL, HDSL, VDSL, RADSL, cable modems. History as well as future trends of these technologies are also addressed. OtherReports on Recent Advances in Networking Back to Raj Jain's Home Page Table of Contents ● 1. Introduction ● 2. DSL Technologies ❍ 2.1 ADSL ■ 2.1.1 Competing Standards ■ 2.1.2 Trends ❍ 2.2 HDSL ❍ 2.3 SDSL ❍ 2.4 VDSL ❍ 2.5 RADSL ❍ 2.6 DSL Comparison Chart ● 3. Cable Modems ❍ 3.1 IEEE 802.14 ❍ 3.2 Model of Operation ● 4. Future Trends ❍ 4.1 Current Trials ● 5. Summary ● 6. Glossary ● 7. References http://www.cis.ohio-state.edu/~jain/cis788-97/rbb/index.htm (1 of 14) [2/7/2000 10:59:54 AM] Digital Subscriber Lines and Cable Modems 1. Introduction The widespread use of the Internet and especially the World Wide Web have opened up a need for high bandwidth network services that can be brought directly to subscriber's homes. These services would provide the needed bandwidth to surf the web at lightning fast speeds and allow new technologies such as video conferencing and video on demand. Currently, Digital Subscriber Line (DSL) and Cable modem technologies look to be the most cost effective and practical methods of delivering broadband network services to the masses. <-- Back to Table of Contents 2. DSL Technologies Digital Subscriber Line A Digital Subscriber Line makes use of the current copper infrastructure to supply broadband services.
    [Show full text]
  • 900152-001-How to Make CAT-5 Twisted-Pair Network Cables
    April 2005 900152-001 - Rev 00 How to make category 5 twisted-pair network cables Introduction The purpose of this document is to show you how to make the two kinds Stranded wire patch cables are often specified for cable segments running of category 5 twisted-pair network cables that can be used to network one from a wall jack to a PC and for patch panels. They are more flexible than or more countertops together with a jukebox to form quick and simple solid core wire. However, the rational for using it is that the constant local area network (LAN). flexing of patch cables may wear-out solid core cable-break it. Also, stranded cable is susceptible to degradation from moisture infiltration, may use an alternate color code, and should not be used for cables longer LANs simplified than 3 Meters (about 10 feet). A LAN can be as simple as two units, each having a network interface card CAT 5 cable has four twisted (NIC) or network adapter and running network software, connected pairs of wire for a total of eight together with a crossover cable. The next step up would be a network individually insulated wires. consisting of (the hub performs the crossover function). Each pair is color coded with one wire having a solid color (blue, orange, green, or brown) twisted around a second wire with a white background and a stripe of the same color. The solid colors may have a white stripe in some cables. Cable colors are commonly described using the background color followed by the color of the stripe; e.g., white-orange is a cable with a white background and an orange stripe.
    [Show full text]
  • Conducted and Wireless Media (Part I)
    School of Business Eastern Illinois University Conducted and Wireless Media (Part I) (October 3, 2016) © Abdou Illia, Fall 2016 2 Learning Objectives Outline characteristics of conducted media Select conducted media in LAN design 3 Major categories of Media Conducted Media – Physically connect network devices Wireless Media – Use electromagnetic waves/radiation 1 4 Conducted Media Twisted Pair cable Coaxial cable Optical Fiber cable Twisted Pair wire 5 Shielded Twisted Pair (STP) Versus Unshielded Twisted Pair (UTP) Typically 2 or more Twisted pair wires & different standards for different applications http://en.wikipedia.org/wiki/Twisted_pair Twisted Pair wire 6 2 Q: Are Shielded Twisted Pairs (STP) affected by interference ? 2 Coaxial cable 7 A single wire wrapped in a foam (or plastic) insulation surrounded by a braided metal shield, then covered in a plastic jacket Cable can be thick or thin Provides for wide range of frequencies Coaxial cable 8 Two major coaxial technologies: Baseband Coaxial tech. Broadband Coaxial tech. Uses digital signaling Transmits anal./digital signals One channel of digital data Multiple channels of data ~1 kilometer w/o repeater ~ 4 kilometer w/o repeater Thin coaxial cable – Typically used for digital data transmission in Ethernet LANs – Typically used for baseband transmission Thick coaxial cable Less – Typically for broadband transmission noise/interference – Typically used for video transmission compared to twisted pairs Coaxial cable 9 Coaxial cable standards: Type ① Ohm rating② Use RG-11 75 ohm Used in 10Base5 Ethernet (known as Thick Ethernet) RG-58 50 ohm Used in 10Base2 Ethernet RG (Radio Guide) specifies characteristics like wire thickness, insulation thickness, electrical properties, etc.
    [Show full text]
  • Certified Data Cabling Installer (DCI) Competency Requirements
    Certified Data Cabling Installer (DCI) Competency Requirements Data Cabling Installers (DCI) are expected to obtain knowledge of basic concepts of copper cabling installation and service, which are then applicable to all the functions required to safely and competently install communications cabling and low voltage premises cabling. Network cabling has many options now and is being used for many applications in addition to data. Copper cabling is also combined with other media applications to create these networks. Once a DCI has acquired these skills, abilities and knowledge and with minimal training, the DCI should be able to enter employment in the telecommunications cabling field. Data Cabling Installers must be knowledgeable and have abilities in the following technical areas: 1.0 SAFETY 1.1 Describe the various forms of personal protective equipment (PPE) that data cabling technicians have at their disposal 1.2 Explain the safety best practices associated with the work area 1.3 Provide an overview of emergency response information and techniques for the workplace that can be found in Material Safety Data Sheets (MSDS or SDS) described in the Hazard Communication Standard (HCS) (29 CFR 1910.1200(g)), revised in 2012, and detailed in Appendix D of 29 CFR 1910.1200 2.0 BASIC ELECTRICITY 2.1 Describe the relationships between voltage, current, resistance and power 2.2 Identify components called resistors and also non-component types of resistance in cabling technology 2.3 Use Ohm’s law to calculate power usage and power losses in cabling
    [Show full text]
  • Lectures 8 -10 2019
    Digital Transmission Digital Transmission Media Error Detection Digital Transmission Transmitted Received Transmitter Signal Signal Receiver Communication channel Transmitter Key questions l Accepts bits from data link l How many bits per second can layer be transmitted reliably across the l Converts bits into digital channel? modulated signal l How much power and Receiver bandwidth is consumed in the l Recovers bits from received process? signal l How do we control error rate in l Transfers bits to its data link delivered bits? layer Transmission Impairments Transmitted Received Transmitter Signal Signal Receiver Communication channel Communication Channels Transmission Impairments l Pair of copper wires l Signal attenuation l Coaxial cable l Signal distortion l Radio l Spurious noise l Light in optical fiber l Interference from other l Light in air signals l Infrared Digital Binary Signal 1 0 1 1 0 1 +A 0 T 2T 3T 4T 5T 6T -A Bit rate = 1 bit / T seconds For a given communications medium: l How do we increase transmission speed? l How do we achieve reliable communications? l Are there limits to speed and reliability? Pulse Transmission Rate l Objective: Maximize pulse rate through a channel, that is, make T as small as possible ??? Channel T t t l If input is a narrow pulse, then typical output is a spread-out pulse with ringing l Question: How frequently can these pulses be transmitted without interfering with each other? l Answer: 2 x Wc pulses/second where Wc is the bandwidth of the channel Multilevel Pulse Transmission l If channel
    [Show full text]
  • Characterization of Twisted Pair Telephone Cable for Broadband Telecommunication Services
    XXIII Simpozijum o novim tehnologijama u poštanskom i telekomunikacionom saobraćaju – PosTel 2005, Beograd, 13. i 14. decembar 2005. CHARACTERIZATION OF TWISTED PAIR TELEPHONE CABLE FOR BROADBAND TELECOMMUNICATION SERVICES Bratislav Milovanović1, Aleksandar Marinčić2, Nebojša Dončov1 1Faculty of Electronic Engineering, Niš 2SANU member, Faculty of Electrical Engineering, Beograd Abstract: Characterization of the existing telephone subscriber loops infrastructure used by the modern broadband telecommmunication services such as xDSL has been presented in the paper. As loop transmission medium quality is one of key requirements for performance capabilities of these services, a method for modelling and simulation of subscriber loops infrastructure in the frequency domain is described. This method is based on ABCD transmission parameters matrix and the appropriate twisted pair cable model representation to account for frequency dependence of its primary per-unit length parameters. It is used to obtain some important subscriber loop characteristics over the service operating frequency band and to analyse quality of cable transmission from the aspect of Heaviside criterion fulfillment. Keywords: Twisted pair, xDSL service, transfer characteristics, insertion loss. 1. Introduction In recent years, internet and its multimedia contents, video service, consumer services and many others become the main source of high-speed data communication demands. Such high data-rate demands exceed the bandwidth of now mature high speed voice band modems (up to 56 kbps). The first higher-speed alternative with access speed at 128 kbps, the Integrated Services Digital Network (ISDN), did not achieve wide popularity due to its high installation cost, some incompatibility with the existing telephone service (POTS - Plain Old Telephone Service), and lack of standardization throughout the industry.
    [Show full text]
  • DATA COMMUNICATION and NETWORKING Software Department – Fourth Class
    DATA COMMUNICATION AND NETWORKING Software Department – Fourth Class Transmission Media Dr. Raaid Alubady - Lecture 7 Introduction In a data transmission system, the transmission medium is the physical path between transmitter and receiver. For guided media, electromagnetic waves are guided along a solid medium, such as copper twisted pair, copper coaxial cable, and optical fiber. For unguided media, wireless transmission occurs through the atmosphere, outer space, or water. The characteristics and quality of a data transmission are determined both by the characteristics of the medium and the characteristics of the signal. In the case of guided media, the medium itself is more important in determining the limitations of transmission. For unguided media, the bandwidth of the signal produced by the transmitting antenna is more important than the medium in determining transmission characteristics. One key property of signals transmitted by antenna is directionality. In considering the design of data transmission systems, key concerns are data rate and distance: the greater the data rate and distance the better. A number of design factors relating to the transmission medium and the signal determine the data rate and distance: Bandwidth: All other factors remaining constant, the greater the bandwidth of a signal, the higher the data rate that can be achieved. Transmission impairments: Impairments, such as attenuation, limit the distance. For guided media, twisted pair generally suffers more impairment than coaxial cable, which in turn suffers more than optical fiber. Interference: Interference from competing signals in overlapping frequency bands can distort or wipe out a signal. Interference is of particular concern for unguided media, but is also a problem with guided media.
    [Show full text]
  • UNIT:3 Transmission Media
    UNIT:3 1 Transmission media SYLLABUS 3.1 Types of Transmission Media 3.2 Guided Media: Twisted Pair, Coaxial Cable, Fiber 3.3 Un Guided Media : Electromagnetic spectrum, Radio Transmission, MicrowaveTransmission, InfraredTransmission, Satellite Communication 2 WHAT IS NETWORK CABLING? Cable is the medium through which information usually moves from one network device to another. There are several types of cable which are commonly used with LANs. 3 3.1 TYPES OF TRANSMISSION MEDIA CATEGORIES/CLASSIFICATION OF TRANSMISSION MEDIA/CABLE 4 3.2 GUIDED MEDIA: TWISTED PAIR, COAXIAL CABLE, FIBER Twisted pair and coaxial cable use metallic (copper) conductors that accept and transport signals in the form of electric current. Optical fiber is a glass or plastic cable that accepts and transports signals in the form of light 5 TWISTED PAIR - TRANSMISSION CHARACTERISTICS Limited distance Limited bandwidth (1MHz) Limited data rate (100MHz) Susceptible to interference and noise 6 TWISTED PAIR - APPLICATIONS Most common medium Telephone network Between house and local exchange (subscriber loop) Within buildings To private branch exchange (PBX) For local area networks (LAN) 10Mbps or 100Mbps 7 TWISTED-PAIR CABLE Unshielded Twisted-Pair (UTP) Cable 8 CONTINUE… It is used in telephone systems; its frequency range is suitable for transmitting both data and voice. A twisted pair consists of two conductors (usually copper), each with its own colored plastic insulation. The plastic insulation is color-banded for identification. 9 CONTINUE… Colors are used both too identify the specific conductors in a cable and to indicate which wires belong in pair and how they related to each other pairs in a large bundle.
    [Show full text]