Using Taps to Produce Internal Screw Threads

Total Page：16

File Type：pdf, Size：1020Kb

USING TAPS TO PRODUCE INTERNAL SCREW THREADS WORLD ASSOCIATION OF TECHNOLOGY TEACHERS https://www.facebook.com/groups/254963448192823/ www.technologystudent.com © 2019 V.Ryan © 2019 TRY THE FREE MOBILE INTERACTIVE PDF APPS FOUND AT www.technologystudent.com - FOR ALL YOUR ENGINEERING AND TECHNOLOGY NEEDS AMERICAN TYPE TAP WRENCH REMEMBER ! MOST COMMON METRIC CUTTING COMPOUND TAPPING DRILL SIZES METRIC TAPPING SIZE (M) DRILL SIZE BAR TYPE TAP WRENCH 2mm M2 1.6mm 3mm M3 2.5mm 4mm M4 3.3mm TAPER INTERMEDIATE PLUG 5mm M5 4.2mm TAP TAP TAP THREADING A THROUGH HOLE 6mm M6 5.0mm SQUARE 1 clockwise rotation SECTION USE TAPPING 1/2 rotation back 8mm M8 6.8mm .Ryan © 2019 SHANK SIZE DRILL V V.Ryan © 2019 10mm M10 8.5mm CUTTING COMPOUND UK MADE APPLIED TO 12mm M12 10.2mm UK MADE UK MADE UK MADE TAP 14mm M14 12.0mm THREAD 16mm M16 14.0mm 18mm M18 15.5mm FLUTE THREADING A BLIND HOLE 20mm M20 17.5mm V.Ryan © 2019 V.Ryan © 2019 V.Ryan © 2019 1. TAPER 2. INTERMEDIATE 3. PLUG TAP TAP TAP UK MADE UK MADE UK MADE .Ryan © 2019 .Ryan © 2019 .Ryan © 2019 V V V TRY THE FREE MOBILE INTERACTIVE PDF APPS FOUND AT www.technologystudent.com - FOR ALL YOUR ENGINEERING AND TECHNOLOGY NEEDS USING DIES TO PRODUCE EXTERNAL SCREW THREADS WORLD ASSOCIATION OF TECHNOLOGY TEACHERS https://www.facebook.com/groups/254963448192823/ www.technologystudent.com © 2019 V.Ryan © 2019 TRY THE FREE MOBILE INTERACTIVE PDF APPS FOUND AT www.technologystudent.com - FOR ALL YOUR ENGINEERING AND TECHNOLOGY NEEDS THE STOCK (DIE HOLDER) REMEMBER ! CUTTING AN EXTERNAL THREAD CUTTING COMPOUND DIE STOCK CLOCKWISE V.Ryan © 2019 ADJUSTING SCREWS CIRCULAR SPLIT DIE V.Ryan © 2019 ALTERNATIVE STOCK WITH A FLUTES CENTRAL ADJUSTING SCREW AND TWO OUTER SCREWS VICE CIRCULAR GAPS USING A STOCK WITH THE ASSISTANCE OF THE LATHE USING A TAILSTOCK DIE HOLDER WITH THE ASSISTANCE OF THE LATHE CHUCK TAILSTOCK TAILSTOCK TAILSTOCK CHUCK TAILSTOCK TAILSTOCK TAILSTOCK STOCK SPINDLE HANDLE TAILSTOCK SPINDLE HANDLE AND DIE HOLDER DIE V.Ryan © 2019 V.Ryan © 2019 TRY THE FREE MOBILE INTERACTIVE PDF APPS FOUND AT www.technologystudent.com - FOR ALL YOUR ENGINEERING AND TECHNOLOGY NEEDS.

Copy Link

Recommended publications

Grinding Your Own Lathe Tools
WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING Grinding Your Own Left Hand Right Hand Boring Tool Cutting Tool Cutting Tool Lathe Tools As with any machining operation, grinding requires the Dressing your grinding wheel is a part of maintaining the utmost attention to “Eye Protection.” Be sure to use it when bench grinder. Grinding wheels should be considered cutting attempting the following instructions. tools and have to be sharpened. A wheel dresser sharpens Joe Martin relates a story about learning to grind tools. “My by “breaking off” the outer layer of abrasive grit from the first experience in metal cutting was in high school. The wheel with star shaped rotating cutters which also have to teacher gave us a 1/4" square tool blank and then showed be replaced from time to time. This leaves the cutting edges us how to make a right hand cutting tool bit out of it in of the grit sharp and clean. a couple of minutes. I watched closely, made mine in ten A sharp wheel will cut quickly with a “hissing” sound and minutes or so, and went on to learn enough in one year to with very little heat by comparison to a dull wheel. A dull always make what I needed. I wasn’t the best in the class, wheel produces a “rapping” sound created by a “loaded just a little above average, but it seemed the below average up” area on the cutting surface. In a way, you can compare students were still grinding on a tool bit three months into the what happens to grinding wheels to a piece of sandpaper course.
[Show full text]
Lathe Tooling Guide
LATHE TOOLING GUIDE A reference guide to understanding how cutting tools work and which inserts they pair with. ©Tormach® 2021. All rights reserved. Specifications subject to change without notice. DS10524_Lathe_Tooling_0921B TORMACH.COM Tormach® CNC Lathe Tooling REFERENCE GUIDE To make the most of a machine purchase, it’s important to understand how cutting tools work and which inserts they pair with. Here is some background on lathe cutting tool and insert terminology: ISO/ANSI Inserts Like metric and imperial measurements standards, the U.S. has its own tool TABLE OF insert classification system; they are called American National Standards Institute (ANSI) designations. All of these ANSI classifications can be converted CONTENTS to the International Organization for Standardization (ISO) classifications, but this guide includes both for easier selection. Cutting Tool Designations 3 Turning Tools Cutting tools are easily identified by their designation, which is universal between ISO and ANSI, and, in the machine shop, tool slang often refers to 6 Boring Bars the insert shape, which is also available in the tool designation. Examples and explanations of designations are available at the start of each section. 7 Turning/ Boring Right-Hand vs. Left-Hand vs. Neutral Inserts Right-hand tools are the most commonly used, because they can be used for most turning applications, including making shoulders on the front of the workpiece. Left-handed tools are typically chosen for back turning and making 11 Grooving/ Parting sharp shoulders on the back of the workpiece. Neutral tools are ideal for Tools complex profiling, thanks to their narrow tips. Insert Shapes 12 Grooving/ Parting There are a variety of insert shapes available, but the general note is use Tool Inserts wider inserts for simple geometry and roughing passes, since they have more durability than a more narrow cutting tool, which is needed for complicated or 12 Threading Tools intricate parts.
[Show full text]
Introduction to Turning Tools and Their Application Identification and Application of Cutting Tools for Turning
Introduction to Turning Tools and their Application Identification and application of cutting tools for turning The variety of cutting tools available for modern CNC turning centers makes it imperative for machine operators to be familiar with different tool geometries and how they are applied to common turning processes. This course curriculum contains 16-hours of material for instructors to get their students ready to identify different types of turning tools and their uses. ©2016 MachiningCloud, Inc. All rights reserved. Table of Contents Introduction .................................................................................................................................... 2 Audience ..................................................................................................................................... 2 Purpose ....................................................................................................................................... 2 Lesson Objectives ........................................................................................................................ 2 Anatomy of a turning tool............................................................................................................... 3 Standard Inserts .............................................................................................................................. 3 ANSI Insert Designations ............................................................................................................. 3 Insert Materials
[Show full text]
Variable Speed 7 X 12 In. Metal Lathe
VARIABLE SPEED 7 X 12 IN. METAL LATHE Model # 3455 bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service. NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us at: 800-232-1195 (M-F 8AM-5PM CST) [email protected] WENPRODUCTS.COM TABLE OF CONTENTS Technical Data 2 General Safety Rules 3 Specific Safety Rules For Metal Lathes 4 Electrical Information 6 Know Your Lathe 7 Assembly 8 Operation 9 Maintenance 19 Troubleshooting Guide 20 Exploded View & Parts List 22 Warranty 25 TECHNICAL DATA Model Number: 3455 Motor: 120V, 60Hz, 4A Swing Over Bed: 7 in. (180 mm) Distance Between Centers: 12 in. (300 mm) Spindle Bore: .79 in. (20 mm) Cross Slide Travel: 2-1/2 in. (65 mm) Compound Slide Travel 2.16 in. (55 mm) Speeds: 100 to 2500 RPM Spindle Taper: MT3 Tailstock Taper: MT2 Longitudinal Feed Rate: .1 to .2 mm Screw Threads: 15 to 52 TPI in 18 steps Weight: 81 lbs. 2 GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFE- TY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood.
[Show full text]
Manufacuting Technology
ME 6402 -Manufacturing Technology - II IV Sem / II Year B.E. (Mechanical Engineering) Department of Mechanical Engineering R.M.K.ENGINEERINGCOLLEGE R.S.M. Nagar, Kavaraipettai – 601 206. UNIT I - THEORY OF METAL CUTTING INTRODUCTION: CUTTING TOOL: SINGLE POINT CUTTING TOOL: NOMENCLATURE SINGLE POINT TOOL: MECHANICS OF METAL CUTTING: TYPES OF CHIPS: COOLANT OR CUTTING FLUIDS OR EMULSIONS: FUNCTIONS OR USES OF COOLANTS OR CUTTING FLUIDS: TYPICAL PROPERTIES OF TOOL MATERIALS: ------------------------------X-------------------------------- UNIT-II - CENTRE LATHE AND SPECIAL PURPOSE LATHE INTRODUCTION: TYPES OF LATHE: SPEED LATHE: CENTRE LATHE OR ENGINE LATHE: BENCH LATHE: TOOL ROOM LATHE: CAPSTAN AND TURRET LATHE: SPECIAL PURPOSE LATHE: AUTOMATIC LATHE: CONSTRUCTION OF LATHE MACHINE: BED: HEAD STOCK: TAIL STOCK: CARRIAGE: THREAD CUTTING MECHANISM: ACCESSORIES AND ATTACHMENTS OF LATHE: SPECIFICATION OF LATHE: LATHE OPERATIONS: TAPERS AND TAPER TURNING: TAPER TURNING BY SWIVELLING THE COMPOUND REST: TAPER TURNING ATTACHMENT METHOD: TAPER TURNING WITH TAILSTOCK SET OVER METHOD: FORM TOOL METHOD: TAPER TURNING WITH DOUBLE HEADS: THREAD CUTTING: DRILLING ON A LATHE: CUTTING SPEED: FEED: ---------------------------X------------------------------ UNIT-III, OTHER MACHINE TOOLS DRILLING INTRODUCTION: CONSTRUCTION OF DRILLING MACHINE: TYPES OF DRILLING MACHINE: PORTABLE DRILLING MACHINE: SENSITIVE DRILLING MACHINE: UPRIGHT DRILLING MACHINE: RADIAL DRILLING MACHINE: GANG DRILLING MACHINE: MULTIPLE-SPINDLE DRILLING MACHINE: TYPES OF DRILLS: TWIST DRILL
[Show full text]
Making a Cylindrical Mandrel on a Metal Lathe by John Huth, Lucas Pemberton and Greg Beckwith
Making a Cylindrical Mandrel on a Metal Lathe by John Huth, Lucas Pemberton and Greg Beckwith Sometimes our work quality and speed increases when thee lath bed true, it is possible to make a serviceable we have a mandrel that is precision-sized to the part we cylindrical mandrel by adding a follower rest to your are trying to repair. lathe carriage. The follower rest supports the stock as it is being cut, the contact point being quite close Shorter lengths of precision cylindrical mandrels (1/2” to the tool bit contact point. Since the follower rest is to 4 inch lengths) are easy to produce on a metal lathe. attached to the carriage, it naturally follows the tool bit Your set up is dependent upon the mandrel length: Our up the stock, ensuring a good, dimensionally consistent rule of thumb on set up is: if the stock you are cutting finished product. extends from the chuck less than 3X the diameter, no end support is required; when the stock extension from Here are some tips: the chuck exceeds three times the stock diameter, a live center is required. Without live center support two things can happen: 1. your stock will flex excessively resulting in an inconsistent dimension and finish, or 2. If spinning fast enough, your stock will become a serious danger as centrifugal force whips it into a right angled weapon that could tear flesh and/or break off as a • Make certain your tools are sharp. Dull tools greatly increase the forces causing deflection • For mandrels, we often cut soft standard steels such as 12L14 or 303 stainless steel • The follower rest needs to contact the stock only very.
[Show full text]
BL Series Brake Lathe Industry Leading Combination Bench Lathe
BL Series Brake Lathe Industry leading combination bench lathe BL31 (includes ACT / Digi-Cal 2.0 package, rotor capability, and bench) shown with optional adaptors Key features at a glance OPTIONAL (PATENTED) % Oscillates machining speed to prevent buildup of vibration (chatter) % No bands or other devices required OPTIONAL Digi-Cal 2.0 % Instantly measures drum or rotor dimensions and depth of cut % Calibration holds after power cycling BL33 (includes ACT / Digi-Cal 2.0 package, rotor capability, bench and dust collection hood) shown with optional adaptors OPTIONAL Push button speed control Self-Aligning Nut % Push button control with % Speeds setup three working speeds % Prevents over-tightening % Eliminates belt changes and mounting errors Quick Change % Twin cutters pivot to quickly change from rotors to drums % No storing of cutting head required Disc/Drum Control Lockout % Eliminates potential “crashing” of machine % Warning indication reminder STANDARD Dual LED Work Lamps % Adjustable lamps illuminate both sides of workpiece % Easy push button control STANDARD Adjustable Feed Rate % Dial fast for rapid removal or slow for final surface finish % One-cut pass capable Anti-Chatter Technology with Digi-Cal 2.0 Anti-Chatter Technology eliminates buildup of vibration — stop chatter before it starts! Hunter System Others Oscillating speed Fixed speed Anti-Chatter Technology (ACT) varies spindle speed to Chatter can start when machining rotors at a fixed keep chatter inducing vibration from starting, resulting speed. This is similar to
[Show full text]
Cutoff Lathes and Endfinishers Brochure
Rotating-Head Cutoff Lathes Tube Loading & Endfinishing Systems • Rugged high-speed cutting, grooving, turning and chamfering • More parts per hour, closer tolerances, reduced labor • Fastest changeover • OD/ID chamfers in a single chucking, both ends • Models for round tubing up to 9" diameter, barstock to 3" HAUT-025RCBrochure2RS.indd 2 1/27/10 1:29:15 PM Our History and Our Commitment to You … Hautau is our family name. It is on every machine we build. That’s why we’ll stand behind you on every one 24/7. Hautau makes world-class tube cutoff machines and systems. They are designed, engineered and built by American craftsmen in the fields of southeast Indiana. Charles F. Hautau Sr, company founder, was a gifted inventor who held over 60 patents including rotary-head cutoff and CNC tube bending. Charles Jr. and Fred have carried on the tradition, building a wide range of innovative machinery for over forty years. Among our early machines was one to trim the ends of mufflers. Because the muffler Charlie Hautau could not spin, our design featured a rotating head. After twenty years of building tube cutting and processing machines and other custom automation, we decided to apply the rotating head concept to cutting thick wall steel tubing. This would form the basis for our standard product line. Traditional tube cutoff lathes have a headstock with a through hole up to two feet deep, so tube feeding methods are limited. The tube can be machined on just one end. Short cuts can fly out and long cuts need outboard support rollers.
[Show full text]
Rotary Transfer For
AUGUST 2002 / VOLUME 54 / NUMBER 8 BY ALAN RICHTER, MANAGING EDITOR Rotary transfer machines provide high-volume flexibility. hen it comes xxBrown noted that to high- the company’s ma- Wvolume, chines need oil extended-length pro- coolers for some de- duction runs of complex manding runs. parts or families of parts, eliminating secondary opera- Setting Up tions is highly advantageous. It pre- The setup requirements for a vents tolerance build-up, reduces parts rotary transfer machine depend on handling and maximizes machine effi- the workpiece material, part complex- ciency and profit. For this type of production, ity and the type of part the machine was rotary transfer machines excel. The flexibility of previously running. Brown said setup takes 2 this type of machine also makes it appropriate for to 3 hours when switching a part within the smaller parts quantities. same family and two to three shifts when changing Brown Manufacturing Co. Inc., Plainville, Conn., is a outside a family of parts. case in point. “We were one of the first to use a CNC rotary Since an RTM can be an alternative to a high-volume transfer machine in a job shop environment for smaller quan- production run on a multispindle screw machine, it makes tities rather than dedicated to a certain job,” said Douglas sense that screw-machine shops are some of the biggest Brown, company president. In 1993, the company purchased consumers of RTMs. But screw machinists often don’t have its first CNC rotary transfer machine from St. Louis-based Hy- the proper mindset when it comes to rotary transfer tech- dromat Inc.
[Show full text]
Equipment List
COLUMBIA GEAR EQUIPMENT GEAR GRINDING EQUIPMENT SHAPING EQUIPMENT (2) Gleason Pfauter 600/800 CNC Gear Grinders - 1 w/int Lorenz LS420 CNC Shaper Oerlikon Maag Opal 420 CNC VIT/CBN Gear Grinder Fellows 10-4 Gear Shapers w/4" Risers Niles ZX 1000P Fellows 10-2 Gear Shaper w/6" Riser Hofler 400KK CNC Gear Grinder (5) Fellows Model 20-4 Gear Shapers Niles 630 ZE CNC VIT/CBN Gear Grinder (4) Fellows 36" Gear Shapers w/2" to 8" Risers Niles 400ZE Gear Grinder Fellows 36" Gear Shapers w/12" Tilting Riser w/Range 0 to 8-1/2 ° Hofler Rapid 900 Gear Grinder (3) Gleason 600/800ES Guideless CNC Gear Shaper w/8" Riser Gleason 1600 CNC VIT/CBN Gear Grinder w/int Gleason 600/800S CNC Gear Shaper 4" Riser Gleason 1200/1450 CNC VIT/CBN Gear Grinder w/int (2) Gleason 500 CNC Gear Shapers Liebherr LGG500 Gear Grinder Gleason 1200/1600S Hydro Stroke Liebherr LS500E Shaper GRINDING EQUIPMENT (2) Okamoto IGM-2M MDI Internal Grinders SHAVING EQUIPMENT Okamoto IGM-15N C-2 Internal Grinder (2) Churchill Model GS12SA Shavers Okuma GI-2ON VIT/CBN Bore and Face Grinder National Broach GCV-12 Shaver w/Crowning (2) Okuma GI-2ON 1WS CNC Internal Grinders National Broach GCU-18 Shaver (2) USACH/Tripet 150 CNC VIT/CBN Bore and Face Grinder Cincinnati Milacron Heald Model 2EF73 Sizematic Internal Grinder TURNING EQUIPMENT (2) Mitsubishi RD 32-B100A 12x40 CNC External Grinders (2) Okuma Crown BB CNC Lathes w/Robotic Loader Mitsubishi RD32-B75A CNC External Grinder (3) Okuma Cadet LNC8 CNC Lathes (2) Precise Products Corporation Super 60 Center Hole Grinders (3) Okuma L1420 BB CNC Lathes Excello No.
[Show full text]
Owner's Manual & Safety Instructions
Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. 19j Visit our website at: http://www.harborfreight.com Email our technical support at: [email protected] When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright© 2015 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product. any shape or form without the express written consent of Harbor Freight Tools. Failure to do so can result in serious injury. Diagrams within this manual may not be drawn proportionally. Due to continuing SAVE THIS MANUAL. improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. Specifications Tap & Die Scale SAE Material Carbon Steel 4-36 5/16"-18 6-32 5/16"-24 8-32 3/8"-16 10-24 3/8"-24 Tap & Die Sizes 10-32 7/16"-14 12-24 7/16"-20 1/4"-20 1/2"-13 1/4"-28 1/2"-20 1/8" NPT pipe tap IMPORTANT SAFETY INFORMATION Use Precautions 1.
[Show full text]
A South Bend "Set up and Cut" Shaper Pamphlet
330. The Metal Shaper. The metal working shaper is used principally for machining flat surfaces. These PHOTO COURTESY SOUTH BEND LATHE WORKS A. Clapper Box O. Feed Rod B. Down-feed Handle P. Table Elevating Crank C. Head Q. Cross-feed Crank D. Head Swivel Lock Screw R. Cross-rail E. Ram Clamping Handle S. Base F. Ram T. Work-table Support G. Switch Box U. Support Locking Handle H. Hand Wheel V. Work Table J. Drive-pulley Guard W. Vise K. Motor X. Lamp L. Motor Cradle Y. Tool Post M. Tension Release Lever Z. Tool Holder N. Eccentric surfaces may be any angle to one another. Irregular surfaces may also be machined on the shaper. The body or column of the shaper carries a ram which reciprocates back and forth over the work which is clamped in the vise. METAL WORK - BENCH AND MACHINE 177 The size of the shaper is determined by the maximum length of stroke or travel of the ram. The one shown is a 7" shaper which requires a 1/2 H.P. motor at 1725 R.P.M. 331. Table. The table is mounted on the face of the column. It can be raised or lowered by the table elevat- ing crank and moved transversely by the cross-feed crank. The table has three slots in the top and the left side The table support is always lowered against the base parallel with the ram. The right side has two square slots and locked in position. and one vee slot which are vertical to the ram.
[Show full text]