Marine Investigation Report M98M0003

Total Page:16

File Type:pdf, Size:1020Kb

Marine Investigation Report M98M0003 MARINE INVESTIGATION REPORT M98M0003 ACCIDENT ABOARD SHIP FISHING VESSEL ACAPE CHIDLEY@ 105 MILES EAST OF LOUISBOURG, NOVA SCOTIA 3 FEBRUARY 1998 The Transportation Safety Board of Canada (TSB) investigated this occurrence for the purpose of advancing transportation safety. It is not the function of the Board to assign fault or determine civil or criminal liability. Marine Investigation Report Accident Aboard Ship Fishing Vessel ACAPE CHIDLEY@ 105 miles east of Louisbourg, Nova Scotia 3 February 1998 Report Number M98M0003 Summary Before daybreak, the stern trawler ACAPE CHIDLEY@ was fishing off the coast of Nova Scotia when the crew experienced difficulty in retrieving the trawl net. During an attempt to clear a riding turn of gilson wire on a winch drum, a trawlerman positioned himself near a block which was rigged to help pull the gilson wire free. As the pulling force was increased, the block assembly tore from its corroded support and struck the trawlerman, killing him. Ce rapport est également disponible en français. - 2 - Other Factual Information "CAPE CHIDLEY" Port of Registry Halifax, Nova Scotia (N.S.) Flag Canada Registry/Licence Number 370542 Type Large Fishing Vessel Gross Tonnage1 792 Length 42.73 m Built 1976 Propulsion 2400 brake horsepower Number of Crew 14 Registered Owner National Sea Products Limited, Lunenburg, N.S. The ACAPE CHIDLEY@ is a large stern trawler of steel construction with the wheelhouse and accommodation forward and a mechanised working deck over the fish hold aft. A forward gantry straddles a winch platform just aft of the wheelhouse. The after gantry, which stands astride the stern ramp, houses the port and starboard gallows frames, towing blocks, and trawl door stowage. The vessel had been engaged to catch fish for the French island of Saint-Pierre. On 2 February 1998 at 1010 the trawler departed Saint-Pierre bound for the fishing grounds off the coast of Nova Scotia. Just before daybreak on February 3, the ACAPE CHIDLEY@ was trawling approximately 105 miles from the coast, east of Louisbourg, when the crew experienced difficulty in retrieving the trawl net. Both trawl doors had been hauled up and secured at each port and starboard gallows frame when the hammer lock (steel coupling) at the port door let go, releasing the end of the sweep line pennant. This meant that the sweep lines from the trawl door to the net could not be harnessed using the pennant in the normal way for bringing the net on board. 2 In order to correct the situation, the port trawl door had to be manoeuvred from the gallows frame and brought on deck to capture the free end of the pennant for normal net retrieval. 1 Units of measurement in this report conform to International Maritime Organization standards or, where there is no such standard, are expressed in the International System of units. 2 The pennant is a wire cable with one end attached to the net=s sweep lines and the other secured at the trawl door with a releasable hammer lock. The pennant at each door is used to transfer the sweep lines and net from the trawl doors for independent hauling of the net on deck via the stern ramp. - 3 - The master had approximately 27 years= working experience with National Sea Products of Lunenburg. He was relatively new to this vessel, having sailed on her for three trips. He had asked the chief mate to remain on the bridge to demonstrate the procedure used on board this vessel for retrieving the trawl door. Using the gilson winch and cable over the gilson block at the head of the forward gantry, the crew attempted to lead the cable aft to the port trawl door. When slackening-off the gilson cable by rotating the winch drum, a riding turn of wire on the gilson drum jammed the cable and prevented it from being hauled out by hand. The capstan winch was then used to forcibly clear the riding turn of cable on the gilson drum (see Appendix A - Arrangement of Cable, Rope and Blocks). In order to free the jammed cable, a rope was harnessed to the end of the gilson cable. It was then led through an overhead guide block at the top of the port gallows frame, down through a yo-yo block with a working limit of five tons, attached at the aft bulwark, and led to a capstan winch located on the port side of the afterdeck. The master warned all hands to stand clear as the cables and rope under strain ran the full length of the working deck. There was partial success in clearing the riding turn on the gilson drum and this provided some additional cable aft for eventual hook up to the port trawl door. The process to free the cable from the drum was such that there were times of maximum strain on the capstan winch and others when the cable would go slack as it was being cleared. The trawlerman went aft to handle the required slack in the gilson cable and to hook it onto the port trawl door. This placed him immediately in front of the yo-yo block and approximately 2 m from the capstan winch operator. There was no communication between them. The crew member who was operating the capstan winch continued to take the strain on the cable as it became slack. At a coincident moment when the strain was being taken, and the trawlerman was immediately in front of the block, a section of the bulwark stay in way of the block ripped away from the after ship=s structure. The five-ton block, together with its safety chain and the lug, hit the trawlerman on the left side of his lower jaw and he fell to the deck. The trawlerman, who had approximately seven years= fishing experience, was wearing a Canadian Standards Association-approved hard hat at the time. The master rushed down to the afterdeck from the wheelhouse to determine the status of the trawlerman. Unable to get a pulse, the master, via the ship=s radio and a Canadian Coast Guard radio station, was able to communicate with a doctor ashore. Together they determined that the trawlerman was deceased. The vessel initially steamed for North Sydney and subsequently changed course for Louisbourg, where representatives from National Sea Products and other interested authorities including the RCMP and Nova Scotia=s Department of Environment and Labour,3 met the vessel. 3 Formerly called Department of Labour. - 4 - Block Securing Arrangement The bulwark was stiffened by bulwark stays which comprised 12.7 cm x 7.62 cm x 0.95 cm inverted ordinary angle irons (see Appendix B - Photographs). The long flange of the angle iron (the standing flange) was at right angles and welded onto the bulwark. The face flange was parallel to the bulwark and had a pad-eye and a lug welded to it, which were used for securing blocks during fishing operations. Of the two rigging attachments, the one near the upper end was a lug and the other, approximately 12.5 cm below it, was a pad-eye. The general practice was to shackle the yo-yo block to the lower pad-eye and secure the safety chain to the upper lug. In this instance, both the yo-yo block and the safety chain were shackled to the upper lug. Post-Occurrence Examination Following the occurrence, the accident site was examined; observations included the following: $ The face flange of the bulwark stay in way of the upper lug to which the yo-yo block was secured was severely corroded, wasted, and bent beyond the original 90-degree angle; this was particularly noticeable in the area of the upper rigging attachment. $ Other bulwark stays on the after deck, which were used for similar purposes, were in like condition and some had holes cut in the standing flange to take the block safety chain. $ The open link safety chain for the yo-yo block in use had one partially wasted link. TSB Engineering Laboratory The Engineering Laboratory of the TSB conducted an examination and in-depth analysis of the bulwark stay and the lug to which the yo-yo block was fastened, and the conclusions drawn included the following:4 $ The fracture occurred in the angle iron. $ No metallurgical defects were found in the weld nor was it considered to have adversely affected the strength of the adjacent metal. $ The strength of the fractured structure at the time of the failure was roughly of the same magnitude as the maximum pull of the winch. The pull of the winch combined with the dynamic loading effects were such that the weakened section of the bulwark stay failed. Regulatory Ship Inspection by Transport Canada 4 TSB Engineering Laboratory Report No. LP 039/98 - Examination of Fractured Lug is available upon request from the Transportation Safety Board of Canada. - 5 - Periodic inspection of the external and internal hull of the vessel was carried out by a Transport Canada, Marine Safety (TCMS) surveyor on 16 January 1998, some two weeks before the occurrence. Following inspection, the vessel was issued an unqualified ship inspection certificate. The record indicates that no SI-7 was issued to the vessel; SI-7s identify deficiencies that do not materially affect the seaworthiness of the vessel but, being safety-related, are required to be rectified as soon as possible or within a period indicated on the certificate. Occupational Health and SafetyCWorkplace Legislation and Training The Occupational Health and Safety Act (1996) of Nova Scotia and the regulations made pursuant thereto apply to the work deck space aboard fishing vessels.
Recommended publications
  • Installation and Maintenance Manual Winch Performa 46.2 STP
    Installation and Maintenance Manual MRPW-05 Performa™ Winch 46.2 STP 46.2 STQP Index Introduction 3 Technical characteristics 3 Performance data 3 Weight 3 Maximum working load 3 Technical characteristics - Winch Quattro Performa 4 Performance data 4 Weight 4 Maximum working load 4 Outline 3 Winch 46.2 STP 3 Outline - Winch Quattro Performa 4 Winch 46.2 STQP 4 Installation 5 Installation procedure 6 Positioning the self-tailing arm 9 Maintenance 9 Washing 9 Maintenance table 9 Disassembly procedure 9 Exploded view with maintenance products 13 Assembly 14 Harken® limited worldwide warranty 15 Ordering spare parts 15 Exploded view 16 Performa Winch 46.2 STP 16 Performa Winch 46.2 STQP 18 Parts list 20 Performa Winch 46.2 STP 20 Performa Winch 46.2 STQP 21 Performa™ Winch 46.2 STP 2 Installation and Maintenance Manual Introduction - Technical characteristics - Outline Introduction This manual gives technical information on winch installation and maintenance, including disassembling and reassembling. This information is DESTINED EXCLUSIVELY for specialised personnel or expert users. Installation, disassembling and reassembling of the winch by personnel who are not experts may cause serious damage to users and those in the vicinity of the winch. Harken® accepts no responsibility for defective installation or reassembly of its winches. In case of doubt the Harken® Tech Service is at your disposal at [email protected] This Manual is available only in English. If you do not fully understand the English language, do not carry out the operations described in this Manual. Technical characteristics Power ratio Gear ratio 1st speed 11,70 : 1 2,30 : 1 2nd speed 46,50 : 1 9,20 : 1 The theoretical power ratio does not take friction into account.
    [Show full text]
  • 82 Subpart 77.03—Marine Engineering Systems
    § 77.03±1 46 CFR Ch. I (10±1±98 Edition) 100 Barr Harbor Drive, West Conshohocken, PA Miscellaneous machinery alarms and con- 19428±2959 trols. ASTM F1014±1986, Standard Specification for General alarm systems. Flashlights on Vessels: 77.35±5(c) (b) Electrical equipment installed in [CGD 82±042, 53 FR 17704, May 18, 1988, as spaces ``specially suitable for vehicles'' amended by CGD 95±072, 60 FR 50463, Sept. 29, shall be in accordance with subchapter 1995; CGD 96-041, 61 FR 50729, Sept. 27, 1996; CGD 97±057, 62 FR 51045, Sept. 30, 1997] J (Electrical Engineering) of this chap- ter. Subpart 77.03ÐMarine [CGFR 65±50, 30 FR 16953, Dec. 30, 1965, as Engineering Systems amended by CGFR 66±33, 31 FR 15283, Dec. 6, 1966; CGFR 68±32, 33 FR 5716, Apr. 12, 1968; § 77.03±1 Installation and details. CGD 74±125A, 47 FR 15231, Apr. 8, 1982] (a) The installation of all systems of a marine engineering nature, together Subpart 77.06ÐLifesaving with the details of design, construc- Appliances and Arrangements tion, and installation, shall be in ac- cordance with the requirements of sub- § 77.06±1 Installation. chapter F (Marine Engineering) of this The installation of all lifesaving ap- chapter. Systems of this type include pliances and arrangements must be in the following: accordance with the requirements of subchapter W (Lifesaving Appliances Steering systems. Power for going astern. and Arrangements) of this chapter. Bilge and ballast systems. [CGD 84±069, 61 FR 25288, May 20, 1996] Tank vent and sounding systems. Overboard discharges and shell connections.
    [Show full text]
  • Boat Handling
    Canadian Coast Guard Auxiliary Search & Rescue Crew Manual BOAT 6 HANDLING The skills involved in handling a vessel are learned over time and come with practice. A new boat handler will fair better if they un- derstand and can apply some of the princi- ples and basic tools outlined in this chapter. “The difference between a rough docking and a smooth easy docking is around 900 attempts.” BOAT HANDLING CONTENTS 6.0 Introduction . .101 6.1 Helm Position . .101 6.2 Forces on Your Vessel . .103 6.2.1 Winds . .103 6.2.2 Waves . .103 6.2.3 Current . .104 6.2.4 Combined natural forces . .104 6.3 Vessel Characteristics . .104 6.3.1 Displacement Hulls . .104 6.3.2 Planing Hulls . .105 6.4 Propulsion and Steering . .107 6.4.1 Pivot Point . .108 6.4.2 Trim . .108 6.5 Propellers . .109 6.5.1 Parts of a Propeller . .109 6.6 Basic Manoeuvres . .110 6.7 Manoeuvring . .110 6.7.1 Directed Thrust . .110 6.7.2 Twin Engine Directed Thrust . .110 6.7.3 Waterjets . .112 6.7.4 Non-Directed Thrust and Rudder Deflection . .112 6.8 Getting Underway . .113 6.9 Approaching the Dock . .113 6.10 Station Keeping . .114 100 Canadian Coast Guard Auxiliary Search & Rescue Crew Manual Excerpts taken from the book “High Seas High Risk” Written by Pat Wastel Norris 1999 (The Sudbury II was a legendary offshore salvage tug that had taken a large oil drilling platform in tow during the summer of 1961. This drama occurred in the Caribbean as Hurricane Hattie approached.) The Offshore 55, a towering oil rig, was at that time the largest rig in the world.
    [Show full text]
  • United States National Museum
    SMITHSONIAN INSTITUTION UNITED STATES NATIONAL MUSEUM BULLETIN 2 30 WASHINGTON, D.C. 1964 MUSEUM OF HISTORY AND TECHNOLOGY The Bark Canoes and Skin Boats of North America Edwin Tappan Adney and Howard I. Chapelle Curator of Transportation SMITHSONIAN INSTITUTION, WASHINGTON, D.C. 1964 — Publications of the United States National Aiuseum The scholarly and scientific publications of the United States National Museum include two series, Proceedings of the United States National Museum and United States National Museum Bulletin. In these series the Museum publishes original articles and monographs dealing with the collections and work of its constituent museums—The Museum of Natural History and the Museum of History and Technology setting forth newly acquired facts in the fields of Anthropology, Biology, History, Geology, and Technology. Copies of each publication are distributed to libraries, to cultural and scientific organizations, and to specialists and others interested in the different subjects. The Proceedings, begun in 1878, are intended for the publication, in separate form, of shorter papers from the Museum of Natural History. These are gathered in volumes, octavo in size, with the publication date of each paper recorded in the table of contents of the volume. In the Bulletin series, the first of which was issued in 1875, appear longer, separate publications consisting of monographs (occasionally in several parts) and volumes in which are collected works on related subjects. Bulletins are either octavo or quarto in size, depending on the needs of the presentation. Since 1902 papers relating to the botanical collections of the Museum of Natural History have been published in the Bulletin series under the heading Contributions Jrom the United States National Herbarium, and since 1959, in Bulletins titled "Contributions from the Museum of History and Technology," have been gathered shorter papers relating to the collections and research of that Museum.
    [Show full text]
  • DF-629 Fastwinder Winch Owner's Manual
    NABRICO DF-629 BARGE CONNECTING WINCH Owner’s Manual OM-DF629-001-A THIS PAGE IS INTENTIONALLY LEFT BLANK. NABRICO DF-629-40-HL-6 BARGE CONNECTING WINCH Owner’s Manual NABRICO DF-629-40-HL-6 BARGE CONNECTING MANUAL WINCH Owner’s Manual CONTENTS SAFETY INFORMATION ........................................................................................ 4 1.1 GENERAL INFORMATION ............................................................................. 5 1.2 INSTALLATION OF EQUIPMENT ................................................................... 6 1.3 INSTALLATION OF WIRE ROPE .................................................................... 8 2.1 OPERATING THE WINCH .............................................................................. 10 3.1 EQUIPMENT INSPECTION ........................................................................... 13 3.2 EQUIPMENT LUBRICATION ......................................................................... 15 3.3 CLEANING AND STORAGE .......................................................................... 16 A.1 DIMENSIONAL .............................................................................................. 18 A.2 EQUIPPED WIRE ROPE ................................................................................ 19 A.3 PARTS BREAKDOWN ................................................................................... 20 A.4 PARTS LIST ................................................................................................... 21 NOTES ..................................................................................................................
    [Show full text]
  • Skilful Vessel Handling
    Skilful Vessel Handling Capt. Øystein Johnsen MNI Buskerud and Vestfold University College March 2014 Manoeuvring of vessels that are held back by an external force This consideration is written in belated wisdom according to the accident of Bourbon Dolphin in April 2007 When manoeuvring a vessel that are held back by an external force and makes little or no speed through the water, the propulsion propellers run up to the maximum, and the highest sideways force might be required against wind, waves and current. The vessel is held back by 1 800 meters of chain and wire, weight of 300 tons. 35 knops wind from SW, waves about 6 meter and 3 knops current heading NE has taken her 840 meters to the east (stb), out of the required line of bearing for the anchor. Bourbon Dolphin running her last anchor. The picture is taken 37 minutes before capsizing. The slip streams tells us that all thrusters are in use and the rudders are set to port. (Photo: Sean Dickson) 2 Lack of form stability I Emil Aall Dahle It is Aall Dahle’s opinion that the whole fleet of AHT/AHTS’s is a misconstruction because the vessels are based on the concept of a supplyship (PSV). The wide open after deck makes the vessels very vulnerable when tilted. When an ordinary vessel are listing an increasingly amount of volume of air filled hull is forced down into the water and create buoyancy – an up righting (rectification) force which counteract the list. Aall Dahle has a doctorate in marine hydrodynamics, has been senior principle engineer in NMD and DNV.
    [Show full text]
  • Nautical Education for Offshore Cxtractivc
    Lso-B-7i-ooz NAUTICALEDUCATION FOR OFFSHORE CXTRACTIVC INDUSTRIES RV G-H.HOFFMANN WITH FREDTOWNSEND AND WARREN NORVILLE 5' GRAHT PUI3I.ICATIOHHO. LSU-II-77-OL C6NTCRfOR WETLAND RESOURCES ~ LOUISIANA STATC UNIVf RSIEY ~ BATON ROUCIC, LOUISIANA 7000 NAUTICAL EDUCATION FOR THE V~M$pQog767 QoM G. H. Ho f fmann with Fred Townsend and Warren Norville LOUISIANA STATE UNIVERSITY CENTER FOR WETLAND RESOURCES BATON ROUGE, LA 70803 Sea Grant Publication No. LSU-8-77-001 September 1977 This work is a result of research sponsored jointly by the Terrebonne Parish School Board and the Louisiana Sea Grant Program, a part of the National Sea Grant Program maintained by the National Oceanic and Atmospheric Administration of the U.S. Department of Commerce. CONTENTS List of Figures List of Tables Vi Acknowledgments Beginnings of the Oil Industry 1 2 The Offshore Revolution Drilling a Wildcat Well The Petr omar ine Fleet 46 6 4.1 Tankers 4.2 Seagoing Tank Barges and Tugs ll 4.3 Inland Tank Barges and Towboats 13 4.4 Inland Drilling Barges 16 4.5 Offshore Drilling Tenders 16 4.6 Submersible Drilling Vessels 17 4.7 3ack-up DrilIing Barges 18 4.8 Semi-Submersible Drilling Vessels 19 4.9 Drill Ships 20 4.10 Crewboats 27 4.11 Supply vessels 28 4.12 Tugs 30 4.13 Derrick Barges 31 4.I4 Pipelaying Barges 31 4.15 Air Cushion Vehicles ACV! 37 Producing Oil and Gas 37 Design Procedures 44 6.1 Owner Requirements 44 6.2 Design Drawings and Specifications 45 6.3 Regulatory Agencies 49 6.4 Design Calculations 54 6.5 The Measurements of a Ship 60 6.6 Free Surface 68 6.7 Model Testing 69 Construction Procedure 70 7.1 Estimating 70 7.2 Working Plans 72 7.3 Production 74 7.4 Inspection 76 7.5 Trials and Tests 78 Delivery 80 Stability and Trim 82 9.1 Stability 82 9.2 Transverse Metacenter 86 9.3 Calculating GM 87 9.4 KM and KG 88 9.
    [Show full text]
  • Csa Winch Procedures
    CSA WINCH PROCEDURES Cover photo courtesy Neil Van Lieu TABLE OF CONTENTS 1. SCOPE ............................................................................................................................................. 1 2. REFERENCES ................................................................................................................................. 1 3. WINCH DESCRIPTION ................................................................................................................... 1 4. CREW ROLES ................................................................................................................................. 2 4.1 WINCH CAPTAIN ...................................................................................................................... 3 4.2 WINCH OPERATOR ................................................................................................................. 3 4.3 WINCH OBSERVER/TRAINEE ................................................................................................. 3 4.4 SHAG DRIVER .......................................................................................................................... 4 4.5 WING RUNNER ........................................................................................................................ 4 4.6 FLAGGER.................................................................................................................................. 4 4.7 PILOT .......................................................................................................................................
    [Show full text]
  • Cornshuckers and San
    INFORMATION TO USERS This reproduction was made from a copy of a document sent to us for microfilming. While the most advanced technology has been used to photograph and reproduce this document, the quality of the reproduction is heavily dependent upon the quality of the material submitted. The following explanation of techniques is provided to help clarify markings or notations which may appear on this reproduction. 1.The sign or “target” for pages apparently lacking from the document photographed is “Missing Page(s)”. If it was possible to obtain the missing page(s) or section, they are spliced into the film along with adjacent pages. This may have necessitated cutting through an image and duplicating adjacent pages to assure complete continuity. 2. When an image on the film is obliterated with a round black mark, it is an indication of either blurred copy because of movement during exposure, duplicate copy, or copyrighted materials that should not have been filmed. For blurred pages, a good image of the page can be found in the adjacent frame. If copyrighted materials were deleted, a target note will appear listing the pages in the adjacent frame. 3. When a map, drawing or chart, etc., is part of the material being photographed, a definite method of “sectioning” the material has been followed. It is customary to begin filming at the upper left hand comer of a large sheet and to continue from left to right in equal sections with small overlaps. If necessary, sectioning is continued again—beginning below the first row and continuing on until complete.
    [Show full text]
  • Marine Investigation Report M90L3034
    Transportation Safety Board Bureau de la sécurité des transports of Canada du Canada MARINE OCCURRENCE REPORT SINKING OF THE FISHING VESSEL “NADINE” GULF OF ST. LAWRENCE 16 DECEMBER 1990 REPORT NUMBER M9 0 L3 0 3 4 The Transportation Safety Board of Canada (TSB) investigated this occurrence for the purpose of advancing transportation safety. It is not the function of the Board to assign fault or determine civil or criminal liability. Marine Occurrence Report Sinking of the Fishing Vessel "NADINE" Gulf of St. Lawrence 16 December 1990 Report Number M90L3034 Synopsis On 16 December 1990, while returning in heavy weather from fishing grounds in the Gulf of St. Lawrence, the "NADINE", a 37-metre fishing vessel, listed to port and sank by the stern. A search and rescue operation was immediately undertaken to locate the ten people aboard. Two crew members were rescued and the bodies of six victims were recovered. Two crew members are still missing. The Board determined that the "NADINE" sank because the openings on the afterdeck and in the transverse bulkheads were not secured. Water was thus able to enter the vessel and eventually flood the lazaret, the fish holds and the engine-room. This ingress gradually reduced the vessel's stability until all reserve buoyancy was lost and the vessel sank. Poor weather, darkness, lack of training and the suddenness of the sinking hindered the abandonment and contributed to the loss of life. 08 April 1994 Ce rapport est également disponible en français. TABLE OF CONTENTS Table of Contents Page 1.0 Factual Information ................................................... 1 1.1 Particulars of the Vessel ..........................................
    [Show full text]
  • Running Rigging Plans Sheet 1 of 12 Dh-04-17 View Looking Fwd Under Sheet Winch Pedestal
    MAINTAMER BOOM ILLUSTRATED, SELDEN BOOM SIMILAR BAILS BY SELDEN GOOSENECK BY SELDEN HARKEN 6058 FAIRLEADS ON MAINTAMER BLOCKS (5) OR SELDEN BOOM TURNING BLOCK SHACKLES TO GOOSENECK BAIL MAINSHEET USES 115' (35M) 1/2" (12mm) BRAID, EYE SPLICE ONE END HARKEN CARS & TRACK ASSY. SEE DH-04-18, HARDTOP FITOUT SHEET DESCENDS THROUGH UP TO SHEET STARBOARD FAIRLEAD IN MAST CLUTCH & WINCH MOUNTING PLATE TO MAST BASE ORGANIZERS, SEE DH-04-15 FROM MAST BASE ORGANIZERS MAIN SHEET TACKLE HARKEN 6058 75MM ANTARES 44 DECK HARDWARE BLOCK AT SHEET PEDESTAL TURNING BRACKET RUNNING RIGGING PLANS SHEET 1 OF 12 DH-04-17 VIEW LOOKING FWD UNDER SHEET WINCH PEDESTAL FIRST ISSUE NOV.6 2003 T. C. FIRST USED VESSEL 4408 HARKEN 6058 BLOCK AT JIB CLEW HARKEN OVER THE TOP BLOCK 3002, MOUNTS ON MAST PLATE SELF-TACKING JIB SHEET IS 108' (33M) X 3/8" (10mm) DYNEMA HARKEN 6058 BLOCKS ON CARS AND PORT PADEYE HARKEN PADEYE 688, P&S HARKEN 1617 3m TRACK, COMPOUND BEND AS PER DH-04-20 HARKEN CAR ASSEMBLY 2 OF 1624 CAR 1 OF 1614 COUPLER 2 OF 1561 TOGGLE SHEET DESCENDS THROUGH HARKEN PIN STOPS STARBOARD FAIRLEAD IN MAST 1624, P&S MOUNTING PLATE TO MAST BASE HARKEN END STOPS ORGANIZERS, SEE DH-04-15 1522 P&S UP TO SHEET CLUTCH & WINCH SELF TACKING JIB SHEET TACKLE FROM MAST BASE ORGANIZERS ANTARES 44 DECK HARDWARE RUNNING RIGGING PLANS HARKEN 6058 75MM BLOCK AT SHEET PEDESTAL TURNING SHEET 2 OF 12 BRACKET DH-04-17 VIEW LOOKING FWD T. C. UNDER SHEET WINCH PEDESTAL LINE ENTERS AND EXITS FURLING LINE IS AS CHAIN LOCKER THROUGH TWO HARKEN 134NP BULLET ORIGINAL SUPPLIED WITH FURLEX.
    [Show full text]
  • Manual for Furling Mast TYPE RB Mk 4
    595-065-E 2020-03-23 Manual for Furling mast TYPE RB Mk 4 Contents: Page: Contents: Page: Product description 2 Fitting and hoisting the sail 8 Checks and adjustments before Stepping 4 Before sailing 9 Line routing 6 Maintenance 10 Operation 7 2 Product description • Seldén furling mast allow for convenient setting and reefing of the mainsail. • The unique design of the halyard swivel bearing distributes the load over the whole ball race to give smoother furling and the lowest possible friction, even under high loads. • The new Mk 4 compact gear mechanism offers improved gear efficiency, allows a smaller mast cutout and is prepared for easy retro fit of electric furling drive unit. • This Instruction Manual has been compiled to give you information on the furling mast reefing system. Study it and follow the instructions carefully, and we guarantee you pleasurable use from your Seldén furling mast. Follow the relevant rigging instructions in our booklet ”HINTS AND ADVICE” for tuning the rig. Fig. 2:1 Sail compartment with luff extrusion 3 Top swivel Halyard swivel Access to sail feeder and Sail feeder halyard swivel Tensioning screw Tack hook Access to tack hook and tensioning screw Outhaul car Rachet lever Winch handle socket Line driver Fig 3:1 4 Checking luff extrusion tension prior to stepping the mast The luff extrusion is correctly tensioned before leaving the factory, but tension can be re-checked before stepping the mast in the following manner. Lay the mast horizontally on the side and keep it straight. The luff extrusion should now be just clear off the mast wall at its midpoint.
    [Show full text]