Procedure for Cutting Top at Job Site and Refinishing Edge Tools and Accessories Needed

Total Page：16

File Type：pdf, Size：1020Kb

Procedure for Cutting top at job site and refinishing edge Tools and accessories needed • 15- Amp 7-1/4 in. Circular Saw • Dry-cutting Diamond Circular Saw Blade • 2 C-Clamps • Belt Sander • 100 Grit Sanding Belts • Straight board or piece of back splash to use as a guide while cutting • Measure Length of piece before cutting piece down to actual size • Then measure the inside of you blade to the edge of the saw plate that will be running against your fence or guide. After this dimension has been determined then subtract that amount plus the amount that will need to be cut off from the length of your top. Example the dimension from blade to outside dimension of plate is 5.62 and the amount to be cut off of the piece will be 2.00” the overall measurement will be 7.62”. • Mark 7.62” and place the piece of material that will be used for your fence on the mark then clamp fence down. • Be sure to put some tape on the surface of the top to avoid any scratching .Then proceed in cutting the piece. • Once piece has been cut remove C-clamps and finish cut edge with belt sander to remove all the saw marks if needed. • If a bevel finish is required place the belt sander flat against the edge of the top and remove all saw marks. Then place the belt sander at an angle to apply the bevel be sure not to apply to much pressure when making the bevel because it may cause the belt to dig into the material when finished repeat the process on the bottom also. The bevel should be 1/8 when completed. • Once piece is finished the edge can then be painted..

Copy Link

Recommended publications

High Gloss Splashback Fabrication & Installation Manual Watch Video Online of H Ow to Cut and Install Gunnersendiy.Com.Au CAUTION
DO-IT-YOURSELF High Gloss Splashback Fabrication & Installation Manual Watch video online of h ow to cut and install gunnersendiy.com.au CAUTION General safety precautions should be used when handling Splash. Suitable gloves and safety eyewear should be worn at all times. Manual lifting and handling practices should be used with a minimum of 2 people at all times. Adhesives required £Neutral Cure Silicone (Recommended: Selleys 3 in 1 Clear 300g.) £Double sided Tape (Recommended: Perma Mounting Tape Everyday Bulk Reel 12mm x 20m.) Basic tools required £Pencil for marking £Measuring Tape £Circular Saw to make long straight cuts (Recommended Blade: Irwin 184mm 120T 20/16 PVC Circular Saw Blade.) £Straight Edge to guide circular saw £Clamps to hold straight edge and Splash during cutting £Drill and Jigsaw (If small holes are required. E.g. Power points) £Sandpaper for finishing edges. (80, 220 & 500 grit for final finish) 2 FOR ARCHITECTURAL INTERIOR DESIGN HIGH GLOSS Acrylic Panels Fabrication & Installation Manual Protective Film Both sides of Splash are protected by a film. Be sure to leave the protective film on the panel throughout the marking, cutting and machining process to ensure the finish is kept in perfect condition. We strongly recommend avoiding external storage, or extended periods of exposed transport (uncovered flatbed truck). The protective film and adhesive could be damaged, making the removal of film difficult. Storage Splash must be stored in a dry location. For added protection, long term storage should be protected by an additional polyethylene cover. The flatness of the panels could be altered if panels are stored or transported in humid conditions.
[Show full text]
Resource Book for Furniture Renovation, Refinishing And
DOCUMENT RESUME ED 224 910 CE 034 646 AUTHOR Barton, Diane; Robinson, Jay TITLE Resource Book forFurniture.Renovation, Refinishing and Aeupholstering. INSTITUTION Madison Area Technical Collo Wis.;Wisconsin State Board of Vocational, Asechnical, andAdult Education, Wadison. PUB DATE 82 MOTE 69p.; For related document?, see CE034 642-649. PyB,TYPE Guides - Classroom Use - Guides (ForTeachers) (052) EDRS PRICE MFOI/PC03 Plus Postale. DESCEcIPTORS Adult Proarams; Adult VocationalEducation: *Furniture; Glossaries; *Home Fbrnishings;Learning Aciivities, *Occupational-Ho" Economics; *Resource Materials IDENTIFIERS *Furniture Refini,shing; *Upholsterers This resource book for furniturerenovation (refinishing and reupholstering) is one of four resourcebooks .developed.for,use in Code 30 or adultvocational programs in the home furnishings service area.-Representative,illustrative, and book are Furniture informative materials cont4ned in the resource 4 Woods, Cuts and Matching Vdneers,'WoodJoints, Joints Used In Furniture Construction, Vocabulary ofWood, Wood Classification, Exotic Woods, Woods Physical Propertiesavd Source Chart, Chronology of Furniture Styles, Dictionaryof Upholstery Terms, Upholstery Materials and Supplies, FurnitureFabrics, Estimating Fabrics to Reupholster Vari.ous Pieces ofFurniture, Removing Old Cover, Construction Processes in Upholstery,Spring and Spring Work, Attaching Burlap, Determining Size ofTack for Job, and Installing Final Coverings. (YLB) ********************w************************************************* Reproductions
[Show full text]
Richlite Fabrication Guide Cirque Distribution
RICHLITE FABRICATION GUIDE CIRQUE DISTRIBUTION Enhancing innovative design through sales, distribution and support of premium architectural, maker and specialty building materials. TABLE OF CONTENTS FABRICATION GUIDE and OVERVIEW.......... 4 TROUBLESHOOTING.............................26 DELIVERY, HANDLING and STORAGE.......... 5 CANTILEVER GUIDELINES...................... 27 PLANNING.......................................... 7 PROPERTIES.......................................28 CUTTING ............................................ 9 MSDS................................................29 ROUTING............................................ 11 WARRANTY........................................30 DRILLING .......................................... 13 IMPORTANT LINKS...............................33 CNC MACHINING.................................. 14 SEAMING........................................... 16 ASSEMBLIES....................................... 18 SURFACE FINISHING............................. 19 APPLIED FINAL FINISHES.......................22 CARE and MAINTENANCE.......................24 RICHLITE FABRICATION GUIDE The.following.document.describes.how.Richlite.paper.composite.is.received,. handled,.and.fabricated..These.guidelines.should.ensure.that.your.experience. with.Richlite.is.informed.and.positive..Richlite.is.not.like.any.other.material.avail- able.and.by.following.the.instructions.below,.it.is.not.difficult.to.fabricate.and. the.results.are.tremendously.rewarding. Please.note,.these.are.general.guidelines.and.it.is.recommended.that.any.fab-
[Show full text]
Woodworking Glossary, a Comprehensive List of Woodworking Terms and Their Definitions That Will Help You Understand More About Woodworking
Welcome to the Woodworking Glossary, a comprehensive list of woodworking terms and their definitions that will help you understand more about woodworking. Each word has a complete definition, and several have links to other pages that further explain the term. Enjoy. Woodworking Glossary A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | #'s | A | A-Frame This is a common and strong building and construction shape where you place two side pieces in the orientation of the legs of a letter "A" shape, and then cross brace the middle. This is useful on project ends, and bases where strength is needed. Abrasive Abrasive is a term use to describe sandpaper typically. This is a material that grinds or abrades material, most commonly wood, to change the surface texture. Using Abrasive papers means using sandpaper in most cases, and you can use it on wood, or on a finish in between coats or for leveling. Absolute Humidity The absolute humidity of the air is a measurement of the amount of water that is in the air. This is without regard to the temperature, and is a measure of how much water vapor is being held in the surrounding air. Acetone Acetone is a solvent that you can use to clean parts, or remove grease. Acetone is useful for removing and cutting grease on a wooden bench top that has become contaminated with oil. Across the Grain When looking at the grain of a piece of wood, if you were to scratch the piece perpendicular to the direction of the grain, this would be an across the grain scratch.
[Show full text]
Care and Maintenance
Care and Maintenance ACQUASTONE worksurfaces are easy to clean and Scratches and Refinishing: maintain. By following the simple care instructions, Day to day scratches and marks can easily be the beauty of your worktops can be preserved and sanded and buffed out. your bathroom will retain that ‘just installed’ look throughout its life. Light Scratches: Using a sanding block, attach the 320 grit Routine Cleaning: sandpaper and repeat the process with the THE ULTIMATE BATHROOM SURFACESOLUTION Wiping your ACQUASTONE surface with a damp 500 grit finishing pad. On all the sanding cloth and then buffing with a dry cloth, will keep your processes apply with a light smooth circular surface in pristine condition. motion, do not force the action, do not dig in. Wipe clean with a clean damp cloth using the Care and Maintenance: a Wax Free Polish* and allow to dry. Avoid exposing ACQUASTONE surface to strong Restore to the orginal finish by applying chemicals such as nail varnish remover, paint ACQUASTONE finishing compound and removers etc. these should be removed immediately. buffing clean with a dry polishing cloth. Finally any residue and spills from, shampoo, toothpaste, apply a wax free polish* and buff with a clean mouthwash etc, should be cleaned immediately with dry cloth to finish. soapy water to ensure no staining occurs, however these stains can easily be removed by applying Deeper Scratches: ACQUASTONE finishing compound with a clean Using a sanding block, attach the 240 grit dry cloth, then buffing with a wax free polish* with a sandpaper and repeat the process with the clean dry cloth.
[Show full text]
EC1154 Refinishing Woodwork Floors Furniture Rizpah A
University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Historical Materials from University of Nebraska- Extension Lincoln Extension 3-1946 EC1154 Refinishing Woodwork Floors Furniture Rizpah A. Douglass Follow this and additional works at: http://digitalcommons.unl.edu/extensionhist Douglass, Rizpah A., "EC1154 Refinishing Woodwork Floors Furniture" (1946). Historical Materials from University of Nebraska- Lincoln Extension. 2448. http://digitalcommons.unl.edu/extensionhist/2448 This Article is brought to you for free and open access by the Extension at DigitalCommons@University of Nebraska - Lincoln. It has been accepted for inclusion in Historical Materials from University of Nebraska-Lincoln Extension by an authorized administrator of DigitalCommons@University of Nebraska - Lincoln. WOODWORK FLOORS FURNITURE Refinishing Woodwork, Floors and Furniture Rizpah A . Douglass Because of shortages of materials and lack of labor and time, many families have not made needed repairs around the house. Even though most farm families will still be exceedingly busy, some of the needed materials may soon be available again, the refinishing of woodwork, floors or furniture will doubtless be given an important place in home activities and the directions that follow will prove useful. General Directions for Refinishing Woods Remove old finish. Best results are obtained when all the old finish is removed, especially if the finish is in a poor condition. The main objects are to remove it without injuring the wood and with as little labor as possible. Commercial paint and varnish remover may be more expensive but it is less likely to injure the wood than is home-made remover. Commercial removers are inflammable. Do not use them in a closed room or around a fire.
[Show full text]
The COMPLETE GUIDE to Sanding and Refinishing Wooden Floors the COMPLETE GUIDE to Sanding and Refinishing Wooden Floors
The COMPLETE GUIDE To Sanding and Refinishing Wooden Floors The COMPLETE GUIDE To Sanding And Refinishing Wooden Floors Contents Introduction Floor Sanding • How To Use A Floor Sander • How To Use An Edge Sander • How To Sand The Corners • Rough Grit Sanding • Climbing The Grits • Finishing Sanding • Filling The Floor Floor Coating and Finishing • Lacquering • Hardwax Oiling • Staining • Coloured F inishes • Floor Paint Floor Specific Information • Sanding Floorboards • Sanding Hardwood Floors • Sanding Herringbone Parquet • Sanding Finger B lock Mosaic Parquet www.HowToSandAFloor.com Page 2 of 48 The COMPLETE GUIDE To Sanding And Refinishing Wooden Floors Introduction Everyone dedicates their books to someone, and if I had to dedicate this book to anyone, it would be to my 4 month old (as of writing) son, Chester. The proceeds from this little eBook will be put aside so he has a better childhood than I did. 10 years and 1 month ago, I started a new job as a floor sanding professional. I received no training at all, I was just put on the tools and that was it. I hated it for the first 3 years. My boss had told me that he had been doing it for 7 years when he had only been doing it for 4 months. We were making every mistake imaginable, and there were a lot of mistakes to make. He did have a good attitude towards learning though: try everything and see what works best. Like many people, I found mastery and then passion, not the other way round. It is a profession that comes with a lot of job satisfaction.
[Show full text]
Wood Cabinet Renewal Products
Wood Cabinet Renewal Products Is Sandy always write-in and untoned when nib some subahs very competently and mesally? Apolitical Chaddy disyokes some patronymic after wrong-headed Sturgis imbricates smatteringly. Nelsen cross-stitch her guile dang, labiate and mutual. The cabinets are able to wood cabinet renewal franchise updates from High-quality wood cabinets are one solid candidates for refinishing Replacing your cabinets is both huge banner that self not completely necessary if. Completely chemically stripped it now, you for more time if special offers a soothing look professionally done with silicone free kitchen! Attics Basements Bathrooms Bedrooms Cabinets Ceilings Cleaning. Home Depot's cabinet refacing partner N-Hance Wood Renewal says. There are proud of dirt is forgotten. How did for your favorite affordable wood renewal process is renew highly professional service brings a secretary of bleached such information. The string way in clean kitchen cabinets is by thoroughly degreasing them using a heavy-duty degreaser You can use liquid dish soap was as safe Simple Green M1 liquid deglosser TSP or you start use a product called Krud Kutter A green Scotch-Brite pad works great to complex all surfaces. Or poverty can use any ready-made brush-on product such as Minwax White Wash. My area of dirt away. We renovate the highest quality wood coatings and finishing products furniture polishes. Odors such a cigarette it can overlap into wooden furniture through the smell can really but Many will get rid of quality furniture because even this odor. My kitchen storage is messier now on a kitchen is time, wipe over like they deserve with a few hours before you can penetrate into account.
[Show full text]
Cabinet Transformations™ Wood Refinishing System
TECHNICAL DATA CAB-03 CABINET TRANSFORMATIONS™ WOOD REFINISHING SYSTEM DESCRIPTION AND USES PRODUCT APPLICATION Cabinet Transformations™ Wood Refinishing System is a Watch the entire instructional DVD and use the printed long lasting rejuvenation system that brings back the original instructions for the complete, step by step, procedure on color and finish of stained wood cabinetry. It is not a stain application of the materials. and it will not change the color of your cabinets. Cabinet Transformations Wood Refinishing system is suitable for IMPORTANT: Apply when air (ambient) temperature is 50- cabinets, vanities, interior doors, moldings and furniture. 90°F (10-35°C) and relative humidity is below 60%. Covers up to 100 square feet or 40 linear feet. SURFACE PREPARATION Cabinet Transformations uses a system of a wood cleaner, To obtain best results, take cabinet doors off hinges and color enhancer and protective topcoat to create a highly drawers out of frames. Remove all cabinet hardware, durable finish. including hinges, drawer pulls, and knobs. The surface of the cabinets must be completely cleaned in accordance to the Tintable to one of 18 finish colors. The color appropriate kit instructions to ensure proper performance of the Cabinet must be tinted at the paint counter at time of purchase. Transformations Wood Refinishing System. The Cabinet Transformations Wood Refinishing System kit APPLICATION OF WOOD CLEANER includes both an instructional DVD and printed instructions to aid with the process and coating application. The kit also The Cabinet Transformations Wood Cleaner prepares the includes: surface and allows the Color Enhancer to adhere without sanding or priming.
[Show full text]
ASE Collision Repair and Refinish Tests
THE OFFICIAL ASE STUDY GUIDE ASE Collision Repair and Refinish Tests INCLUDES DAMAGE ANALYSIS & ESTIMATING! ASE COLLISION REPAIR AND REFINISH TESTS Table of Contents Overview ................................................................................................ 3–8 Collision Repair/Refinish Tests ........................................................... 9–38 • Painting and Refinishing (B2) ...........................................................9 • Non-Structural Analysis and Damage Repair (B3) .........................14 • Structural Analysis and Damage Repair (B4) .................................20 • Mechanical and Electrical Components (B5) .................................25 • Damage Analysis and Estimating (B6) ...........................................33 Test Prep & Training ............................................................................... 39 COPYRIGHT © 2021 by National Institute for AUTOMOTIVE SERVICE EXCELLENCE All rights reserved OVERVIEW Introduction The Official ASE Study Guide for the Collison Repair and Refinish Tests is designed to help collision technicians prepare for the ASE certification tests. This guide contains detailed information about content of the tests in the Collison Repair and Refinish series. The task list for each test, found in the following pages, should help you review your technical knowledge. Your focus should be on less familiar topics. This should make it easier to select additional reference materials that will help you prepare for your test(s). ASE's voluntary certification
[Show full text]
Refinishing Outer Wood Paneling of the Simpson Strong Tie Building
Refinishing Outer Wood Paneling of the Simpson Strong Tie Building Isidoro Amalfitano Cal Poly San Luis Obispo San Luis Obispo, CA This paper outlines the refurbishment of the exterior wood panels located on the Simpson Strong Tie Building on the Cal Poly San Luis Obispo campus. This project focuses on the two large 50 square foot wooden panels that act as an exterior skin for the Simpson Strong Tie Building. This project is an individual project that was broken up into 4 phases. This paper will cover all 4 phases of the refurbishment process. These phases include the removal, sanding, staining and reapplication of wood panels onto the Simpson Strong Tie Building. Furthermore, this paper will go in depth about the building permit process and the struggles experienced communicating with the owner and architect during the preconstruction phase. Many struggles had to be overcome during the refurbishment process such as managing a project on an active campus, as well the refurbishment process itself. There were many unforeseen conditions that were experienced during the construction phase due to inadequate project details from the architect, OMNI Design Group. The purpose of this project is to give back to the Cal Poly San Luis Obispo Construction Management Department by refurbishing the weathered and aesthetically unappealing exterior wooden panels on the Simpson Strong Tie Building. Key Words: Wood Panels, Refurbishment, Weathered, Unforeseen Conditions, Cal Poly Introduction This project is located in Building 187 on the Construction Management courtyard at Cal Poly San Luis Obispo. This building is used as a demonstration lab for various lab-based classes that the Construction Management program has to offer.
[Show full text]
12011-Minwax Onlinefloorguide Approved
Floor Refinishing & Care Guide Hardwood oors provide years of beauty, warmth and elegance for your home. The Minwax® line of quality wood nishing and maintenance products will help you restore and preserve the richness of your hardwood oors, revitalizing their appearance and adding to the value of your home. Restoring and renishing hardwood oors is a large job, but it is one that DIY-ers can do, with some preparation and the right tools. The information in this booklet will give you your rst steps toward tackling this rewarding project! Step 1 Prepare the Room and Floor The Room: • Remove all objects from the room, including furniture, drapes, pictures, knick-knacks, items in closets, vent covers, etc. • Cover any permanent objects that you do not want to get dusty (chandeliers and other light xtures, shelving, etc.) Make sure that any light xtures are o. • Snugly cover door openings to minimize the spread of dust. Remove these covers after sanding, before you stain or apply polyurethane. • Place a mat or cloth outside the entrance to the room so you can wipe your feet as you leave. • Carefully remove any quarter round molding from the base molding, then remove the base molding. Tip! Number each piece of molding on its back using pencil, and put the same number on the wall where you removed the piece. This way, you can put the pieces back in place more easily once the oor is done. • Turn o air conditioning/heat to prevent dust from circulating throughout the house. • Cover all vents. • Open all windows for ventilation.
[Show full text]