TE-OS 18/1 Li 4460717

EN Original operating instructions Cordless Corner Palm

7

Art.-Nr.: 4460719 I.-Nr.: 11019

TE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1 17.06.2019 10:17:30 - 2 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 2 117.06.20197.06.2019 10:17:3110:17:31 1

1 3

4

2 5

2 3

4

5 4

- 3 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 3 117.06.20197.06.2019 10:17:3110:17:31 4 5 5

5 2

6 7

6

- 4 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 4 117.06.20197.06.2019 10:17:3310:17:33 EN

Table of contents 1. Safety information 2. Layout and items supplied 3. Intended use 4. Technical data 5. Before starting the equipment 6. Operation 7. Cleaning, maintenance and ordering spare parts 8. Disposal and recycling 9. Storage

Einhell USA LLC · 305 Veterans Blvd · Carlstadt · NJ 07072 · USA

- 5 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 5 117.06.20197.06.2019 10:17:3410:17:34 EN

Danger! - Read the operating instructions to reduce the risk of injury

Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.

Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the to work on any materials containing asbestos!

Caution! Wear safety goggles. Sparks generated during work or splinters, chips and dust emitted by the equipment can cause loss of sight.

104°F (+40°C) 50°F (+10°C)

Store the batteries only in dry rooms with an ambient temperature of 50°F to 104°F (+10°C to +40°C). Place only fully charged batteries in storage (charged at least 40%).

- 6 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 6 117.06.20197.06.2019 10:17:3510:17:35 EN

DANGER! body is earthed or grounded. When using the equipment, a number of safety c) Do not expose power to rain or wet precautions must be observed to avoid injuries conditions. Water entering a power tool will and damage. Please read the complete operating increase the risk of electric shock. instructions and safety information with due care. d) Do not abuse the cord. Never use the Keep these operating instructions in a safe place cord for carrying, pulling or unplugging so that the information is available at all times. If the power tool. Keep cord away from you give the equipment to any other person, hand heat, oil, sharp edges or moving parts. over these operating instructions and the safety Damaged or entangled cords increase the information as well. We cannot accept any liability risk of electric shock. for damage or accidents which arise due to e) When operating a power tool outdoors, failure to follow these instructions and the safety use an extension cord suitable for information. outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric 1. Safety information shock. f) If operating a power tools in a damp DANGER! location is unavoidable, use a residual Read all the safety information and current device (RCD) protected supply. instructions. Failure to adhere to the safety Use of an RCD reduces the risk of electric information and instructions set out below shock. may result in electric shock, fi re and/or serious injury. Keep all the safety information and 3) Personal safety instructions in a safe place for future use. a) Stay alert, watch what you are doing and use common sense when operating a General safety information for power tools power tool. Do not use a power tool while The term „power tool“ used in the safety you are tired or under the infl uence of regulations refers to power tools operated from drugs, alcohol or medication. A moment of the mains power supply (with a power cable) and inattention while operating power tools may to battery operated power tools (without a power result in serious personal injury. cable). b) Use personal protective equipment. Always wear eye protection. Protective 1) Work area safety equipment such as dust mask, non-skid a) Keep work area clean and well lit. safety shoes, hard hat, or hearing protection Cluttered and dark areas invite accidents. used for appropriate conditions will reduce b) Do not operate power tools in explosive personal injuries. atmospheres, such as in the presence of c) Prevent unintentional starting. Ensure fl ammable liquids, gases or dust. Power the switch is in the off -position before tools create sparks which may ignite the dust connecting to power source and/or or fumes. BATTERY pack, picking up or carrying the c) Keep children and bystanders away while tool. Carrying power tools with your fi nger on operating a power tool. Distractions can the switch or energising power tools that have cause you to lose control. the switch on invites accidents. d) Remove any adjusting key or wrench 2) Electrical safety before turning the power tool on. A wrench a) Power tool plugs must match the outlet. or a key left attached to a rotating part of the Never modify the plug in any way. Do power tool may result in personal injury. not use any adapter plugs with earthed e) Do not overreach. Keep proper footing (grounded) power tools. Unmodifi ed plugs and balance at all times. This enables and matching outlets will reduce risk of better control of the power tool in unexpected electric shock. situations. b) Avoid body contact with earthed or f) Dress properly. Do not wear loose grounded surfaces such as pipes, clothing or jewellery. Keep your hair, radiators, ranges and refrigerators. There clothing and gloves away from moving is an increased risk of electric shock if your parts. Loose clothes, jewellery or long hair can be caught in moving parts.

- 7 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 7 117.06.20197.06.2019 10:17:3510:17:35 EN

g) If devices are provided for the connection h) Keep handles and grasping surfaces of dust extraction and collection facilities, dry, clean and free from oil and grease. ensure these are connected and properly Slippery handles and grasping surfaces do used. Use of these devices can reduce dust not allow for safe handling and control of the related hazards. tool in unexpected situations. h) Do not let familiarity gained from frequent use of tools allow you to become 5) Battery tool use and care complacent and ignore tool safety a) Recharge only with the charger specifi ed principles. A careless action can cause by the manufacturer. A charger that is severe injury within a fraction of a second. suitable for one type of battery pack may create a risk of fi re when used with another 4) Power tool use and care battery pack. a) Do not force the power tool. Use the b) Use power tools only with specifi cally correct power tool for your application. designated battery packs. Use of any other The correct power tool will do the job battery packs may create a risk of injury and better and safer at the rate for which it was fi re. designed. c) When battery pack is not in use, keep it b) Do not use the power tool if the switch away from other metal objects, like paper does not turn it on and off . Any power tool clips, coins, keys, nails, screws or other that cannot be controlled with the switch is small metal objects that can make a dangerous and must be repaired. connection from one terminal to another. c) Disconnect the plug from the power Shorting the battery terminals together may source and/or remove the battery pack, cause burns or a fi re. if detachable, from the power tool before d) Under abusive conditions, liquid may be making any adjustments, changing ejected from the battery; avoid contact. accessories, or storing power tools. Such If contact accidentally occurs, fl ush with preventive safety measures reduce the risk of water. If liquid contacts eyes, additionally starting the power tool accidentally. seek medical help. Liquid ejected from the d) Store idle power tools out of the reach battery may cause irritation or burns. of children and do not allow persons e) Do not use a BATTERY pack or tool that unfamiliar with the power tool or these is damaged or modifi ed. Damaged or instructions to operate the power tool. modifi ed batteries may exhibit unpredictable Power tools are dangerous in the hands of behaviour resulting in fi re, EXPLOSION or untrained users. risk of injury. e) Maintain power tools and accessories. f) Do not expose a BATTERY pack or tool to Check for misalignment or binding of fi re or excessive temperature. Exposure to moving parts, breakage of parts and fi re or temperature above 266°F (130°C) may any other condition that may aff ect the cause explosion. power tool’s operation. If damaged, have g) Follow all charging instructions and do the power tool repaired before use. Many not charge the BATTERY pack or tool accidents are caused by poorly maintained outside the temperature range specifi ed power tools. in the instructions. Charging improperly or f) Keep cutting tools sharp and clean. at temperatures outside the specifi ed range Properly maintained cutting tools with sharp may damage the BATTERY and increase the cutting edges are less likely to bind and are risk of fi re. easier to control. g) Use the power tool, accessories and 6) Service tool bits etc., in accordance with a) Have your power tool serviced by a these instructions and in the manner qualifi ed repair person using only intended for the particular type of power identical replacement parts. This will tool, taking into account the working ensure that the safety of the power tool is conditions and the work to be performed. maintained. Use of the power tool for operations diff erent from intended could result in a hazardous situation.

- 8 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 8 117.06.20197.06.2019 10:17:3510:17:35 EN

b) Never service damaged BATTERY packs. triggers. Place the battery pack in storage Service of BATTERY packs should only be only after it has been fully charged. performed by the manufacturer or authorized 8. Protect batteries and the tool from service providers. overloads. Overloads will quickly result in overheating and cell damage inside the Additional safety instructions battery housing without this overheating We pay a great deal of attention to the design actually being apparent externally. of every battery pack to ensure that we supply 9. Avoid damage and shocks. Replace you with batteries which feature maximum batteries which have been dropped from power density, durability and safety. The battery a height of more than one meter or which cells have a wide range of safety devices. have been exposed to violent shocks without Each individual cell is initially formatted and its delay, even if the housing of the battery pack electrical characteristic curves are recorded. appears to be undamaged. The battery cells These data are then used exclusively to be able inside the battery may have suff ered serious to assemble the best possible battery packs. damage. In this respect, please also read the Despite all the safety precautions, caution waste disposal information. must always be exercised when handling 10. If the battery pack suff ers overloading and batteries. The following points must be overheating, the integrated protective cut- obeyed at all times to ensure safe use. off will switch off the equipment for safety Safe use can only be guaranteed if reasons. Caution! Do not press the ON/OFF undamaged cells are used. Incorrect switch any more if the protective cut-off has handling can cause cell damage. actuated. This may damage the battery. 11. Use only original battery packs. The use Caution! Analyses confi rm that incorrect use and of other batteries may result in injuries, poor care are the main causes of the damage explosion and a fi re risk. caused by high performance batteries. Information on chargers and the charging Information about the battery process 1. The battery pack supplied with your cordless 1. Please check the data marked on the rating tool is not charged. The battery pack has to plate of the battery charger. Be sure to be charged before you use the tool for the fi rst connect the battery charger to a power supply time. with the voltage marked on the rating plate. 2. For optimum battery performance avoid low Never connect it to a diff erent mains voltage. discharge cycles. Charge the battery pack 2. Protect the battery charger and its cable from frequently. damage and sharp edges. Have damaged 3. Store the battery pack in a cool place, ideally cables repaired without delay by a qualifi ed at 59°F (15°C) and charged to at least 40%. electrician. 4. Lithium-ion batteries are subject to a natural 3. Keep the battery charger, batteries and the ageing process. The battery pack must be cordless tool out of children‘s reach. replaced at the latest when its capacity 4. Do not use damaged battery chargers. falls to just 80% of its capacity when new. 5. Do not use the supplied battery charger to Weakened cells in an aged battery pack are charge other cordless tools. no longer capable of meeting the high power 6. In heavy use the battery pack will become requirements and therefore pose a safety risk. warm. Allow the battery pack to cool to room 5. Do not throw battery packs into an open fi re. temperature before commencing with the There is a risk of explosion! charging. 6. Do not ignite the battery pack or expose it to 7. Do not over-charge batteries. Do not fi re. exceed the maximum charging times. These 7. Do not exhaustively discharge batteries. charging times apply only to discharged Exhaustive discharge will damage the battery batteries. Frequent insertion of a charged cells. The most common cause of deep or partly charged battery pack will result in discharge is lengthy storage or non-use of over-charging and cell damage. Do not leave partly discharged batteries. Stop working as batteries in the charger for days on end. soon as the performance of the battery falls 8. Never use or charge batteries if you noticeably or the electronic protection system suspect that the last time they were

- 9 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 9 117.06.20197.06.2019 10:17:3510:17:35 EN

charged was more than 12 months 9. When handling batteries beware of previously. There is a high probability electrostatic charge: Electrostatic discharges that the battery pack has already suff ered cause damage of the electronic protection dangerous damage (exhaustive discharge). system and the battery cells. Avoid 9. Charging batteries at a temperature below electrostatic charging and never touch the 50°F (10°C) will cause chemical damage to battery poles. the cell and may cause a fi re. 10. Do not use batteries which have heated Battery Caution + Disposal during the charging process, as the battery cells may have suff ered dangerous damage. Disposal 11. Do not use batteries which have suff ered Should your appliance need replacement after curvature or deformation during the charging extended use, do not dispose of it with the process or which show other non-typical household refuse, but in an environmentally safe symptoms (gassing, hissing, cracking,…) way. 12. Never fully discharge the battery pack Waste produced by electrical machine (recommended depth of discharge max. items should not be handled like normal 80%) A complete discharge of the battery household rubbish. Please recycle where pack will lead to premature ageing of the recycle facilities exist. Check with your local battery cells. authority or retailer for recycling advice. 13. Never charge the batteries unsupervised. Always dispose of your battery pack according to federal, state, and local regulations. Contact Protection from environmental infl uences a recycling agency in your area for recycling 1. Wear suitable work clothes. Wear safety locations. goggles. ƽ CAUTION! Even discharged battery packs 2. Protect your cordless tool and the battery contain some energy. Before disposing, use charger from moisture and rain. Moisture electrical tape to cover the terminals to prevent and rain can cause dangerous cell damage. the battery pack from shorting, which could cause 3. Do not use the cordless tool or the battery a fi re or explosion. charger near vapors and infl ammable liquids. ƽ WARNING! To reduce the risk of injury or 4. Use the battery charger and cordless tools explosion, never burn or incinerate a battery only in dry conditions and an ambient pack even if it is damaged, dead, or completely temperature of 50°F to 104°F (10°C to 40°C). discharged. When burned, toxic fumes and 5. Do not keep the battery charger in places materials are emitted into the surrounding where the temperature is liable to reach over atmosphere. 40°C. In particular, do not leave the battery 1. Batteries vary according to device. Consult charger in a car that is parked in the sunshine. your manual for specifi c information. 6. Protect batteries from overheating. 2. Install only new batteries of the same type in Overloads, over-charging and exposure to your product (where applicable). direct sunlight will result in overheating and 3. Failure to insert batteries in the correct cell damage. Never charge or work with polarity, as indicated in the battery batteries which have been overheated – compartment or manual, may shorten the life replace them immediately if possible. of the batteries or cause batteries to leak. 7. Storage of batteries, battery chargers 4. Do not mix old and new batteries. and cordless tools. Store the charger and 5. Do not mix Alkaline, Standard (Carbon-Zinc), your cordless tool only in dry places with an or Rechargeable (Nickel Cadmium, Nickel ambient temperature of 50°F to 104°F (10°C Metal Hydride, or Lithium-Ion) batteries. to 40°C). Store the lithium-ion rechargeable 6. Do not dispose of batteries in fi re. battery in a cool and dry place at 50°F to 68°F 7. Batteries should be recycled or disposed of (10°C to 20°C). Protect them from humidity as per state and local guidelines. and direct sunlight! Place only fully charged batteries in storage (charged at least 40%). When shipping or disposing of batteries and 8. Prevent the lithium-ion battery pack from cordless tools, always ensure that they are freezing. Battery packs which were stored packed individually in bags to prevent below 32°F (0°C) for more than 60 minutes short circuits and fi res. must be disposed of.

- 10 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1010 117.06.20197.06.2019 10:17:3510:17:35 EN

Special safety information 2. Layout and items supplied • This tool may be used only for dry grinding/ sanding operations. 2.1 Layout (Fig. 1) • Use on materials containing asbestos is 1. On/Off switch prohibited. 2. Dust extraction adapter • To protect your health, always wear safety 3. Handle goggles and a dust mask during sanding/ 4. Dust collection box grinding work! 5. Oscillating plate • Keep your workplace clean and well 6. Battery capacity indicator illuminated. 7. Battery capacity indicator button • Make sure that the workpiece is sufficiently secured so that it cannot slip. 2.2 Items supplied • Keep children away. Please check that the article is complete as • For your own sake, keep the equipment clean specifi ed in the scope of delivery. If parts are at all times and check it for signs of damage missing, please contact our service center or the each time after using it. store where you made your purchase at the latest • Make sure that the switch is set to OFF before within 5 work days after purchasing the article and you connect up the tool. upon presentation of a valid bill of purchase. • Make sure of your footing, particularly when • Open the packaging and take out the working on ladders and platforms. equipment with care. • Harmful or toxic dust can be produced • Remove the packaging material and any when working on wood or metal. Touching packaging and/or transportation braces (if or inhaling this dust can be harmful for the present). operator and other persons nearby. • Check to see if all the items are supplied. • Hold the equipment by the insulated handles • Inspect the equipment and accessories for because the grinding/sanding belt may strike transport damage. the equipment's own power cable. Damaging • If possible, keep the packaging until the end a live cable may make the metal parts of the of the guarantee period. equipment live and cause an electric shock. • If you discover any damage to the machine, Danger! use the exploded diagram and the spare The equipment and packaging material are parts list to determine which parts need to be not toys. Do not let children play with plastic ordered from Customer Service. bags, plastic sheets and small parts. There is • Important! Wear safety goggles and a dust a risk of choking and suff ocating! mask. • Corner Palm Sander This equipment is not designed to be used by • Dust collection box people (including children) with limited physical, • Abrasive paper (120, 3x) sensory or mental capacities or those with no • Abrasive paper (240, 3x) experience and/or knowledge unless they are • Dust extraction adapter (1x) supervised by a person who is responsible for • Original operating instructions their safety or they have received instructions • Safety information from such a person in to how to use the equipment safely. Children must always be Separately available accessories supervised in order to ensure that they do not 18V 1.5Ah P-X-C lithium-ion battery play with the equipment. 18V 2.0Ah P-X-C lithium-ion battery 18V 2.6Ah P-X-C Plus lithium-ion battery Keep this safety information in a safe place. 18V 3.0Ah P-X-C lithium-ion battery 18V 4.0Ah P-X-C lithium-ion battery 18V 5.2Ah P-X-C Plus lithium-ion battery 18V P-X-C charger

Explore battery + charger options at einhellUSA.com

- 11 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1111 117.06.20197.06.2019 10:17:3510:17:35 EN

3. Intended use CAUTION! Residual risks The equipment is designed for the sanding of Even if you use this electric power tool in wood, iron, plastic and similar materials using the accordance with the instructions, certain appropriate sanding paper. The equipment is not residual risks cannot be eliminated. The suitable for wet sanding. following hazards may arise in connection with the equipment‘s construction and The equipment is allowed to be used only for its layout: prescribed purpose. Any other use is deemed to 1. Lung damage if no suitable protective dust be a case of misuse. The user/operator and not mask is used. the manufacturer will be liable for any damage or 2. Damage to hearing if no suitable ear injuries of any kind resulting from such misuse. protection is applied. 3. Health damage caused by hand-arm Please note that our equipment has not been vibrations if the equipment is used over a designed for use in commercial, trade or longer period or is not properly guided and industrial applications. Our warranty will be voided maintained. if the equipment is used in commercial, trade or industrial businesses or for equivalent purposes. Limit the operating time. All stages of the operating cycle must be considered (for example, times in which the 4. Technical data electric tools are switched off and times in which the tool is switched on but operates without load). Motor power supply: ...... 18 V Idling speed: ...... 12000 min-1 (rpm) Sanding/grinding area: ...... 5. Before starting the equipment ...... 5.9 x 5.9 x 3.9 in. (150 x 150 x 100 mm) Warning! Abrasive paper size (hook-and-loop fastener): .... Always remove the battery pack before making ...... 3.6 x 2.4 x 4.1 in. (93 x 60 x 105 mm) adjustments to the equipment. Oscillatory circuit Ø: ...... 0.06 in. (1.6 mm) Be sure to read the following information before Weight: ...... 1.5 lbs (0.7 kg) you put the cordless equipment into operation: • Charge the battery pack with the charger. If Wear ear-muff s. a rechargeable battery is empty, it must be The impact of noise can cause damage to recharged before you use the equipment for hearing. the first time.

Reduce noise generation and vibration to a 5.1 Fitting the dust collection box (Fig. 2-3/ minimum! Item 4) • Use only equipment that is in perfect • Plug the dust collection box (4) onto the condition. connector. • Maintain and clean the equipment regularly. • The dust is extracted directly into the dust • Adapt your way of working to the equipment. collection box through the abrasive paper and • Do not overload the equipment. the oscillating plate (5). • Have the equipment checked if necessary. • To empty the dust collection box, open the • Switch off the equipment when not in use. box as shown in Fig. 3 and carefully empty it • Wear gloves. by tapping.

5.2 Fitting the dust extractor adapter (Fig. 5/ Item 2) Plug the dust extractor adapter (2) onto the vacuum cleaner connector as shown in Fig. 5. Connect the dust extractor adapter to a suitable dust extraction system.

- 12 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1212 117.06.20197.06.2019 10:17:3610:17:36 EN

Caution! 6.4 Working with the Corner Palm Sander For health reasons it is imperative that you • Place the whole surface area of the sanding use the dust collection box or a dust extraction disk on the material. system. • Switch on the machine and move it with gentle pressure over the workpiece, making 5.3 Fastening the abrasive paper with the circular or transverse and linear movements. hook-and-loop fastening system (Fig. 4) • Use a coarse grit for coarse sanding and a • Only use abrasive paper with the finer grit for finish sanding. You can find the corresponding dimensions and matching appropriate grit size for the job by carrying out perforations. sanding tests. • Place the abrasive paper onto the oscillating plate (4) as shown in Fig. 5. Make sure Note: that the perforations in the abrasive paper If you use the cordless equipment with our 3.0 Ah coincide with the oscillating plate. Power-X-Change rechargeable battery, you will • To remove the abrasive paper, simply pull it be unable to work with the dust collection box (4) off. on account of the size of the battery pack. In this case please use the dust extraction adapter (2). (See 5.2.) 6. Operation Caution! 6.1 Charging the Li battery pack The dusts which are formed while the equipment The corresponding instructions can be found is being used may be a health hazard: in the original operating instructions for your • Always wear safety goggles and a dust mask charger. during sanding work. • All persons who work with the equipment or 6.2 Battery capacity indicator (Fig. 3/item 6) enter the workplace must wear a protective Press the battery capacity indicator switch (7). dust mask. The battery capacity indicator (6) shows the • Eating, drinking and smoking are prohibited charge status of the battery using 3 LEDs. at the workplace. • Paints containing lead are not allowed to be All 3 LEDs lit: used! The battery is fully charged.

2 or 1 LED(s) lit: The battery has an adequate remaining charge.

1 LED fl ashing: The battery is empty, recharge the battery.

All LEDs fl ashing: The battery pack has been deep-discharged and is defective. Do not re-use or charge a defective battery pack.

6.3 Switching on and off (Fig. 1/Item 1) • To switch on the equipment, move the switch (1) from “0” to “1”. • To switch off the equipment, move the switch (1) from “1” to “0”.

- 13 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1313 117.06.20197.06.2019 10:17:3610:17:36 EN

7. Cleaning, maintenance and 8. Disposal and recycling ordering spare parts The equipment is supplied in packaging to HAZARD! prevent it from being damaged in transit. The Always take the battery out of the equipment raw materials in this packaging can be reused or before starting any cleaning work. recycled. The equipment and its accessories are made of various types of material, such as metal 7.1 Cleaning and plastic. Never place defective equipment in • Keep all safety devices, air vents and the your household refuse. The equipment should motor housing free of dirt and dust as far as be taken to a suitable collection center for proper possible. Wipe the equipment with a clean disposal. If you do not know the whereabouts of cloth or blow it down with compressed air at such a collection point, you should ask in your low pressure. local council offi ces. • We recommend cleaning the equipment immediately each time after use. • Clean the equipment regularly with a damp 9. Storage cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive Store the equipment and its accessories out to the plastic parts in the equipment. Ensure of children‘s reach in a dark and dry place at that no water can get into the interior of the above freezing temperature. The ideal storage equipment. The ingress of water into an temperature is between 41°F and 86°F electric power tool increases the risk of an (5°C and 30°C). Keep the electric tool in its electric shock. original packaging.

7.2 Maintenance There are no other parts inside the equipment which require maintenance. The reprinting or reproduction by any other means, in whole or in part, of documentation and 7.3 Ordering replacement parts: papers accompanying the products is strictly Service subject to the express consent of iSC GmbH. 1. If your power tool requires service, contact an authorized USA dealer Subject to technical changes or call the Einhell USA customer service center at 1-866-EINHELL (1-866-346-4355). Only identical replacement parts should be utilized for repairs. This will ensure that the safety of the power tool is maintained. 2. If the battery charger cable is damaged, it must be immediately replaced to avoid a hazard. Contact the Einhell USA® customer service center at 1-866-EINHELL (1-866-346-4355) for assistance.

- 14 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1414 117.06.20197.06.2019 10:17:3610:17:36 EN

EINHELL CUSTOMER PROMISE

QUALITY COMES FIRST. The Einhell name is synonymous with high-performance tools and high-quality European craftsmanship. From cordless to electric lawn mowers, Einhell USA designs and develops state-of-the-art handheld power and garden tools for DIY enthusiasts, hobby gardeners, and handymen. Einhell USA’s quality assurance and engineering teams ensure products are subjected to stringent quality and performance tests. We know that sometimes tough tools go through tough times. In the event that you should experience any issue with your product, you have our commitment that we’ll do everything we can to get you back a tool that’s ready to work as hard as you do.

PRODUCT REGISTRATION: This Warranty is only valid if the Machine is used Einhell strongly encourages you to register and maintained in accordance with the instructions, your purchase. You can register online at warnings and safeguards contained in the owner’s EinhellUSA.com Failure to register your product manual. Einhell will not be responsible for the cost purchase will not diminish your warranty rights. of any unauthorized warranty repairs. This warranty However, registering your purchase will allow Einhell does not cover any cost or expense incurred by the to better serve you with any of your customer service purchaser in providing substitute equipment or service needs. during reasonable periods of malfunction or non-use of this product while waiting for a replacement part or WHAT IS COVERED? unit under this warranty. Einhell warrants to the owner that if this Machine Wearing parts like belts, augers, chains and tines fails within 2 years from the date of purchase due to are not covered under this warranty, and can a defect in material or workmanship or as a result of be purchased at EinhellUSA.com or by calling normal wear and tear from ordinary household use, 1-866-EINHELL (1-866-346-4355). Batteries are Einhell will send a replacement part or product, as covered in full for 90-days from the date of purchase. needed, free of charge and with free shipping to the Repair, replacement or refund of the purchase price original purchaser. If, in Einhell’s sole discretion, the are the exclusive remedies of purchaser and the sole failed Machine cannot be repaired with a part, Einhell liability of Einhell under this warranty. No employee or will elect to either (A) send a new Machine at no charge representative of Einhell is authorized to make any and with free shipping or (B) refund the full purchase additional warranty or any modifi cation to this warranty price to the owner. which may be binding upon Einhell. Accordingly, purchaser should not rely upon any additional WHO CAN SEEK WARRANTY COVERAGE? statements made by any employee or representative This Warranty is extended by Einhell to the owner of Einhell. In no event, whether based on contract, of this Machine (a “Machine” consists of a product indemnity, warranty, tort (including negligence), powered by a motor) for residential and personal strict liability or otherwise, shall Einhell be liable for household use only. This warranty is limited to thirty any special, indirect, incidental, or consequential (30) days from the start of original purchase of any damages, including, without limitation, loss of profi t or EINHELL brand product that is used for commercial revenue. purposes, or any other income-producing purpose. Some states do not allow limits on warranties. In such Should ownership of this machine change during the states, the above limitations may not apply to you. coverage period, please update the Machine’s owner Outside the USA and Canada, other warranties may information at EinhellUSA.com apply.

WHAT IS NOT COVERED? This warranty does not cover any product that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specifi ed in the operator’s manual. This Warranty does not cover cosmetic changes that do not aff ect performance.

- 15 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1515 117.06.20197.06.2019 10:17:3610:17:36 - 16 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1616 117.06.20197.06.2019 10:17:3610:17:36 - 17 -

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1717 117.06.20197.06.2019 10:17:3610:17:36 www.EinhellUSA.com

EH 06/2019 (01)

TTE_OS_18_1_Li_Kit_QVC_USA_SPK7.indbE_OS_18_1_Li_Kit_QVC_USA_SPK7.indb 1818 117.06.20197.06.2019 10:17:3610:17:36