LOGIK HAIR CLIPPERS L10HC10 Manual
Total Page:16
File Type:pdf, Size:1020Kb
SAFETY FIRST! SPECIFICATIONS Please follow all the safety precautions listed below for safety and to reduce the risk Power supply : 230V~, 50Hz, AC Power of injury or electrical shock. Power Consumption : 10W • Check if the voltage indicated on the appliances corresponds to the mains voltage We continually strive to improve our products, specifications may change without in your home before you connect the appliance. prior notice. • Do not damaged the appliance. • Do not use the appliance when one of the attachments is damaged or broken as this may cause injury. Hair Clipper • Keep the appliance out of the reach of children. • Use and store the appliance at a temperature between 15c and 35c. • Always unplug the appliance after use. Instruction Manual • This appliance is only intended for clipping human hair. Do not use it for any other L10HC10 purpose. • Do not immerse the appliance in water or any other liquid. • Do not expose the appliance to excessive moisture, dust or dirt • Always check the blades for alignment. • Always add a few drops of oil before use. • Do not use the appliance if the teeth are damaged. • Always check the appliance for damage before use. If any damage is observed, do not use the appliance. • This appliance has no user repairable parts. • The appliance can become hot during use , only use for 10 minutes ON 10 minutes OFF three cycle . • Always let the appliance cool down before storing. • This appliance is for personal use only. It is not suitable for commercial use. • This appliance should not be left unattended when switch on or when connected to mains supply. • Do not wrap the mains lead around the appliance when hot or when storing. • Do not carry the appliance by the mains lead. • Do not use with wet hands. • Do not use the appliance on damaged or broken skin. • The appliance should never be left unattended when connected to the mains supply. • Children should be supervised to ensure that they do not play with the appliance. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety. • If the mains cable is damaged it must be replaced by the manufacturer, its service Visit Partmaster.co.uk today for the easiest way to agent, or similarly qualified persons in order to avoid a hazard. buy electrical spares and accessories. With over 1 WARNING : Keep the appliance dry. million spares and accessories available we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call 0870 6001 338 (UK customers only) Calls charged at National Rate. This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate Congratulations on the purchase of your new Logik collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the Hair Clipper. product. We recommend that you spend some time reading this instruction manual in order to fully understand all the operational features it offers. Read all the safety instructions carefully before use and keep this instruction manual for future reference. DGS Retail Ltd • Maylands Avenue • Hemel Hempstead • Herts • HP2 7TG • England GB-4 GB-5 UNPACKING FIRST TIME USE GRADUATION Remove all packaging from the hair clipper. Retain the packaging. If you dispose of it 1. Make sure the Power switch is set to 0 (Off). The hair clipper not only allows you to cut the hair evenly at the same length all over please do so according to any local regulations. 2. Remove the plastic protective cover from the cutting blade. the head, it also enables you to achieve a smooth transition from longer hair on top The following items are included: 3. Lubricate the cutting blades with a couple of drops of oil before using the unit for of the head to shorter hair on the back and sides of the head. • The Main Unit the rst time and before using it on each further occasion. 1. Start clipping at the setting for maximum hair length. • Four Comb Attachments: (Lubricating oil tip was sealed, open the tip with cutter or scissors.) 2. Then choose a shorter setting and cut the hair on all parts of the head except the 3mm (1/8”): (P.N.: RAY911-009) 6mm (1/4”): (P.N.: RAY911-010) top, where you want the hair to be longer. 9mm (3/8”): (P.N.: RAY911-011) 12mm (1/2”): (P.N.: RAY911-012) 3. You can repeat this procedure until the hair on every part of the head has the • The Teeth Guard (P.N.: RAY911-008) • The Lubricating Oil (P.N.: RAY911-038) OPERATION desired length. • The Cleaning Brush (P.N.: RAY911-041) • The Comb (P.N.: RAY911-013) Fitting comb attachments • The Scissors (P.N.: RAY913-056) • Instruction Manual (P.N.: L10HC10-001) The hair clipper is supplied with 4 comb attachments that are used to trim the hair to PRECISE CONTOURING WITHOUT COMB ATTACHMENT If items are missing or damaged, please contact Partmaster (UK only). one of 4 different lengths: 1. Remove the comb attachment by pulling it off the hair clipper. Tel: 0870 6001 338 for assistance. • Comb 1 is used to trim hair to a length of 3mm (1/8”). 2. Before contouring the hairline round the ears, comb the hair ends over the ear. PRODUCT OVERVIEW • Comb 2 is used to trim hair to a length of 6mm (1/4”). 3. Bend the person's ear to get it out of the way. • Comb 3 is used to trim hair to a length of 9mm (3/8”). 4. Tilt the hair clipper in such a way that 5. Only cut the hair ends. The hairline only one edge of the cutting element should be close to the ear. Power Dial • Comb 4 is used to trim hair to a length of 12mm (1/2”). touches the hair ends. Cutting Using the hair clipper without a comb attachment will cut off hair with cutting length Blade of around 1.5mm. You can use the adjusting lever on the side of the hair clipper to control the amount of hair to be cut. Lower the lever down for less hair; raise the lever Comb up for more hair. Slide one of the comb attachments over the head of the hair clipper’s fixed cutting blade. Using the hair clipper Adjustable 1. Before you start clipping, make sure the head of the person 6. To contour the nape hairline and the 7. Move slowly and smoothly. Just Lever whose hair you are cutting is at the same level as your chest. sideburns, turn the hair clipper and follow the natural hairline. Power Switch 2. To get the best results, use the hair clipper only on dry hair. make downward strokes. Do not use it on freshly washed hair. Hanging 3. First comb the hair into the direction of hair growth. Loop 4. Switch power switch to “I” on position. 5. Always move the hair clipper against the direction of hair growth, otherwise it will not cut the hair properly. Mains Cable 6. Move the hair clipper through the hair slowly. Clipping with comb attachment 1 2 3 4 CUTTING OVER STYLING COMB OR FINGERS 1. Slide the comb attachment onto the rails on the hair clipper. This technique can be used to obtain hair lengths over 41 mm and 21 mm. Bear in • Select the small or large comb attachment, depending on mind that this technique is dicult to master and should only be applied by the desired hair length. experienced users. 2. Make sure that the arms of the comb attachment have been 1. Make sure the comb attachment is not attached to the properly slid onto the rails on both sides. hair clipper. • Hair length settings Comb Attachments 2. Comb a small section of hair upwards. Lift the hair with a The hair length settings are indicated in millimetres on the styling comb or hold it between your ngers until only arms of the comb attachment. The settings correspond to the length that needs to be cut sticks out. the remaining hair length after cutting. 3. Cut the hair protruding from the comb or fingers. 3. Start at the setting for maximum hair length. 4. Continue this procedure and comb frequently to remove 4. Make sure that the flat part of the comb attachment is cut hair and to check for unevenly cut sections. always fully in contact with the scalp to obtain an even cutting result. CLEANING & STORAGE 5. Pass the hair clipper slowly over the crown from different Clean the hair clipper after every time you use it. Do not use abrasives, scourers or Teeth Guard Lubricating Oil Cleaning Brush Scissors directions to achieve an even cutting result. liquids such as alcohol, petrol or acetone to clean the hair clipper. 6. Make overlapping passes over the head to ensure that the 1. Make sure the hair clipper is switched off and NOTE hair clipper catches all the hairs that need to be cut. unplugged. 7. Comb the hair in the direction of hair growth from time to 2. Make sure the comb attachment is not attached to the Your hair clipper has a power dial. It has already been adjusted for peak eciency time so that the hair clipper can catch the hair more easily.