Firefilm ®Iii – Primers

Total Page:16

File Type:pdf, Size:1020Kb

Firefilm ®Iii – Primers FIREFILM III – PRIMERS The following primers have been determined to be acceptable for use with A/D FIREFILM®III based on adhesion and compatibility characteristics under laboratory conditions in accordance with ASTM D3359-90, Method A and/or ASTM D4541-95. A/D Fire Protection Systems accepts no responsibility for repeatability of these characteristics in the field as may be influenced by variations to primer formulation, curing time, primer recoat characteristics, site conditions, surface preparation and other factors beyond our control. Consult primer manufacturer for primer application and recoat instructions and limitations. Use of primers other than listed is not recommended without prior consultation and approval by A/D Fire Protection Systems. ACE Paint – 33A140 Dunn Edwards – Blockrust 43-4, Korzite continued – Allcolour – 03-4054, 03-4119, Corrobar 43-5, 02PA04, Ameron – Amercoat 5105 and 185HS, Duron – Red Oxide 906-000, 02PR07 (B1930), Valspar V13-F-28 03PA012(B1375), 03PA017(B0950), Farrell-Calhoun- 03PA030, 03PA035, 03PA046, John L. Armitage/ArmorChem - 3500, 6-30 Tuff-Boy Quick Dry Oxide 03PA060 3900 Gray, 4500, SP 1000 red & gray, Fiberlock – LBC*, Fiberset PM 7475, 03PR08, WC 25060B Frazee – 168 prime plus, 545F669 W/R MF4 Anchor Paint MFG. Co. – B-9912 grey, 661F774, 661P728, 23-R612, 28PRK2, Benjamin Moore – 133, 163, Super Spec Ferox- 10828, red oxide, HP Shop-Coat Metal KP1470 primer grey, 19PA09 (B1325), Fresh Start Multi Purpose Oil Based Primer Finishes Unlimited – 72-986, 76-373 19PAK1-WB33, Alkyd White 024-00 Forrest Paint Co. – 16P300X, 16P301, 19PRK3-WB99B, Berlin Co. – Emercoat A-500 16P900, 84P300, 216P317, Krylon Ind. Coatings – K00020002 Grey, K000S4556 Bruning – 232-20 General Paint – 06-110, 06-111, 06- 112, 06-134, 06-154, 06-160 grey, 06- Kuwait – QP8926 Red, QP8006 Gray, Can Lak Inc. – MP-130 162,06-164 grey, 07-701, Laurentide- Canam Grey Dip Primer Carbit – 4E11 Gray R.I. Glidden – Rust-Guard 18226, 162-270, 162278, Carboline – Glid-Guard 27453, 27454, 4160-06120 MAB – 073-189, -424, -444, -450, -499 Carbocoat 115 & 115 SG red & grey, gray Martin Senour Paints – Carbocoat 150 UP & 150 HG, 8229, Griggs – Ratmoore 740 Carbocrylic 120, 3350, 3358, 3359DTM, Airgas 700 grey & 703 red, Carboguard 635, 8922 Hempel – 121U-1148 2-2764 red, 2-2793 grey, Carboline 893SG, 893SG LT, Rustbond, Hentzen – 9770AIA-2, McCormick Paints - 06448 Rustbond FC ICI Devoe– Michigan Industrial Finishes – Multi-Gard GP-5 white (0800) 27452 shop primer canam grey HS10-315 Galoseal WB Bar-Ox 752, Mills Paint - 548 red, 590 Century Industrial Coatings – Devflex 4020 PF white DTM flat, 120-D-123D, -174G, -179B, -199A, - Devguard NA195, 4142, 4160, 4180, Mercury Paint Co. – 199B, -199J, -253B, -263, 4190, 4360 red & gray, Series 3000 #R02-85371, 120-R-186C, -200A, Drywall Flat Primer, Series 3100 Mercguard, 220-D-209B, -215B, -215BX, -252A, - Q.D Shop Coat Primer, Morwear – 1050-769 253A, -268, -275, -310 Rustguard 27453, Passonno – 610-10, -36, 4140-6120 grey Chemcoat – 1000 SP Gray, 41K489, Peerless Coatings – 11-1745 41Y-380A Spraymaster-Pro, Uni-Gripp-WB Aquacrylic, Penta Paints Carribbean – Cloverdale – 70327, 70349, 71024, Pentazinc Chromate 71035, 71333, 71296, 71312, T113, 1- Industries Pepin Ltee– 83001, Quick Dry Shop Coat 71134, 3406-2824 P.F.I. – 5-HES-1101, 5-HPS-1101, T101 QD, T101 QD2, Intercoastal Paint Co. Inc. – 524, 5-S1101C, 8-WP-1126 gray Columbia Paints & Coatings – International – Plasite – 1205 water based acrylic Industrial Universal H2O metal primer – Intercure 200 Polyval – 518709 red oxide, white 05-550-PP, 07-0887-PP, Interprime CPA121/198, Porter – PorterPrime 2.8 Interlac DY, 260 red & grey, 393 red & Con-Lux – Ironox 96 gray PPG – 6-190, 6-208, 90-712, 90-912, gray, 573 grey, Coronado Industrial – 94-232, 94-258 multiprime, FCS 16015 925-147 Shop Kote, Coro Bond DTM Jones Blair Industrial Coatings – red, Maclac Mactek Series 42, ALK FD white 180-11, 15211, 15245, EN-Gray primer-FSC16013, Crown Paint – P209 red K. Bottschen – Red Oxide Primer Pratt & Lambert – 1-5692, QD S3102, Daniel Boone – Shop Prime 6340 Kelly Moore Paints – Kel-Guard Red S4556 red, Tech-gard S4520, Oxide 1710, Kel-Guard White Rust- Precision Master Inc. – 217EZ Davis Frost -23-F603 gray, Inhibitive - 1711 Precision Technical Coatings – Dell & Sons – Lead free Shopcoat red Kessler – 56-090 Steel-Kote metal primer 373-E-1, 373-R-1 Korzite – Pro-Line – Pro-Line 926, Pro-Ox 925 Delta Laboratories –30R001055 red, 0-4507, Prolux –2618-05, 3911-05, 3914-05, Diamond Vogel – QB-5403, QC-0512 0-5097 (B1545), 3006-30374-05, 5349-30769-15, gray acrylic primer, VLX-13436-05, 01PAK3 RMA grey MF2, 01PRK1, Feb. 9, 2018 420 Tapscott Rd., Unit 5, Scarborough, Ontario M1B 1Y4 Tel: (800) 263-4087 or (416 ) 292-2361 · Fax: (416) 298-5887 · www. adfire.com Page 1 of 2 Rodda – Barrier III 708095, 708225, C74AS100, 37H-77 red, 37H- 78 grey, 724471, Corothane I Preprime, B65S14 1C V010-0099 red, Selectone – Corothane I Mio-Aluminum, Tremco – Tremclad Rust Paint Yellow E61AC82 Shopcoat grey, J82, Triangle Coatings – ShopPro red oxide M97, M99, E61A570 Kem Aqua 70P grey MR19, MR27 grey, MR28 grey, MR29R E61A750 KEM FLASH 500, Trinity Coatings – QP 510A red MR50, MR053, WR 99S, WR9900, E61RC21, UCP/Solignum– 1125 fast dry metal Industrial Grey Metal primer SW28, Sheboygan Paint Company - Red alkyd, #Z-1777 fast dry metal alkyd grey Industrial Red Metal primer SW29, anti-corrosion H/S, Oxide 41-8152 Metalastic DTM, B63, B65C10 3128-A & 3128-T alkyd fast primer grey, Sherwin Williams – Sico – Luxsico 525-727, 525-607 A-100 Exterior-#6405-14915, 3138, 3421, 5129 grey, Fast Dry Shop B50A53, Southern Coatings – 700 red 1-2650, Primer Grey (5150), B50AV11 Steel Spec, B50AV2314, 1-1032, 1-2900, 1-5036, 1-6227, Valley Paint MFG. – B50AV2969, B50AV8431, Sumter Coatings – O985, 100D7714, V-003 gray, B50AW3 Fast Dry Primer Gray, 100D8814 gray, 100D9914 V-006 gray, B50AZ8 Kem Bond HS Stiles Paint Mfg. Co.–Tech Prime V-007, B50N2 Kem Kromik Metal, 7-550, V-2453 red, B50NV12, StonCor – Pro-Struct 6230TC grey, Valspar – B50NZ3 Kem Bond HS, 13-R-28 Pheonolic alkyd, B50NZ6 Kem Kromik Universal, Talon Paints – 35 V 55ROP, 513-F-108, B50RV2313, B50WZ1 Kem Kromik, Technical Coatings – 542OD10313, B50RV6227, A16042, WAA01345 B50WZ4 Kem Bond HS, PL2085, Vanex – Plascron Waterborne primer – B50W100, B50WZ30 Galvite HS, W2542, W-2516-WR, gray, B50AZ19 XA07803-LT B55Z -600 Velvacon & Pittsburgh Paint Tnemec – B66A00310, B66W00310 PRO-CRYL, Azeron HS88-0555, 0559 Verco Manufacturing Company – B66A50, Chem-Prime 37H-77W, W2552, B66A580 Enviro-Prime 18-1091, -1092, B66W1 DTM Acrylic, F004-0055 red, B71Y1DTM Wash Primer, Series 4 Versare, B74NT50, Series 10-99, 10-1009, B89N510, Uni-Bond DF Series 115 Sherwin Williams cont.– Uni-Bond 16-AA90, *Fiberlock LBC requires a minimum 60 day curing period prior to application of A/D FIREFILM. A/D Fire Protection Systems 420 Tapscott Rd., Unit 5, Scarborough, Ontario M1B 1Y4 Feb. 9, 2018 Tel: (800) 263-4087 or (416) 292-2361 · Fax: (416) 298-5887 · www. adfire.com Page 2 of 2 .
Recommended publications
  • Interprime 198 Yacht Marine for the Maintenance of Above Water Areas
    Interprime 198 Yacht Marine For the maintenance of above water areas. PRODUCT DESCRIPTION A quick drying, one pack primer. Interprime 198 is surface tolerant, compatible with most substrates and can be overcoated with a wide range of finishes. PRODUCT INFORMATION Colour CPA097-White, CPA098-Grey, CPA099-Red Finish Matt (ISO 2813 : 1978) Specific Gravity 1.25 Volume Solids 41% average (ISO 3233 : 1998) Typical Shelf Life 1 yrs VOC (As Supplied) 506 g/lt Unit Size 5 Lt 20 Lt DRYING/OVERCOATING INFORMATION Drying 5ºC 15ºC 23ºC 35ºC Touch Dry [ISO] 3hrs 1.5hrs 60mins 30mins Hard Dry [ISO] 24hrs 10hrs 4hrs 2hrs Overcoating Substrate Temperature 5ºC 15ºC 23ºC 35ºC Overcoated By Min Max Min Max Min Max Min Max Interlac 665 6hrs 3days 4hrs 2.5days 2hrs 2days 60mins 24hrs Interprime 198 3hrs ext 2hrs ext 60mins ext 30mins ext Interthane 990 24hrs 7days 18hrs 7days 12hrs 7days 6hrs 3days Pre-Kote 24hrs 5days 18hrs 4days 12hrs 3days 8hrs 24hrs APPLICATION AND USE Preparation Use in accordance with the standard Global Yacht specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash as appropriate, to remove all oil, grease, soluble contaminates and other detrimental foreign matter. Maintenance & Repair: Prepare area to be repaired to a minimum of St2 (ISO 8501-1:1998). Higher levels of surface preparation by abrasive blasting to Sa 2 (ISO 8501 - 1:1998) or hydroblasting to HB2M (International Hydroblasting Standards), will enhance product performance. Feather or chip back surrounding area to a sound edge.
    [Show full text]
  • Sds Interprime 198 Grey International Paint
    CPA098_D4 Safety Data Sheet INTERPRIME 198 GREY Sales Order: Sales Order Bulk Sales Reference No.: CPA098 SDS Revision Date: 02/28/2019 SDS Revision Number: D4-3 1. Identification of the preparation and company 1.1. Product identifier Product Identity INTERPRIME 198 GREY Bulk Sales Reference No. CPA098 1.2. Relevant identified uses of the substance or mixture and uses advised against Intended Use Paints and Coatings 1.3. Details of the supplier of the safety data sheet Company Name International Paint LLC Manufacturer: Akzo Nobel Coatings International Paint 6001 Antoine Drive Houston, Texas 77091 National Supplier: Akzo Nobel Coatings Ltd. 110 Woodbine Downs Blvd. Unit #4 Etobicoke, Ontario Canada M9W 5S6 +1 (800) 618-1010 Emergency CHEMTREC (800) 424-9300 International Paint (713) 682-1711 Customer Service International Paint LLC (800) 589-1267 Fax No. (800) 631-7481 2. Hazard identification of the product 2.1. Classification of the substance or mixture Flam. Liq. 3;H226 Flammable liquid and vapor. Skin Irrit. 2;H315 Causes skin irritation. Eye Irrit. 2;H319 Causes serious eye irritation. Skin Sens. 1;H317 May cause an allergic skin reaction. Carc. 2;H351 Suspected of causing cancer. Aquatic Chronic 3;H412 Harmful to aquatic life with long lasting effects. 2.2. Label elements Using the Toxicity Data listed in section 11 & 12 the product is labelled as follows. 1/10 CPA098_D4 Warning. H226 Flammable liquid and vapour. H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H351 Suspected of causing cancer. H412 Harmful to aquatic life with long lasting effects.
    [Show full text]
  • Interprotect (Professional) High Performance Epoxy Primer for Steel, Aluminium and Wood
    Interprotect (Professional) High Performance Epoxy Primer for Steel, Aluminium and Wood PRODUCT DESCRIPTION Quick drying, easy to apply epoxy primer for high performance protection. * Excellent anticorrosive protection * Antifouling tie-coat for use over epoxy primers * Good abrasion resistance PRODUCT INFORMATION Colour YPA400*-White, YPA403*-Grey Finish Matt Specific Gravity 1.4 Volume Solids 45% Mix Ratio 3:1 by volume , Converter/Curing Agent - YPA404* Typical Shelf Life 2 yrs VOC (As Supplied) 464 g/lt Unit Size 750 ml 2.5 Lt 5 Lt DRYING/OVERCOATING INFORMATION Drying 5ºC 15ºC 23ºC 35ºC Touch Dry [ISO] 4hrs 2hrs 1hrs 30mins Immersion 24hrs 18hrs 12hrs 8hrs Pot Life 10hrs 5hrs 3hrs 2hrs Overcoating Substrate Temperature 5ºC 15ºC 23ºC 35ºC Overcoated By Min Max Min Max Min Max Min Max Interfill 830 36hrs 3mths 24hrs 3mths 24hrs 3mths Interfill 830 Fast Cure 36hrs 3mths 24hrs 3mths 24hrs 3mths International/Interlux Antifouling 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Interprotect (Professional) 10hrs 6mths 5hrs 6mths 3hrs 6mths 2hrs 6mths Interspeed Extra Strong 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Interspeed Ultra 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Micron 55 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Micron 66 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Micron CSC 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Micron Extra 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Micron Extra (Professional) 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Perfection Undercoat 24hrs 7days 16hrs 4days 12hrs 2days 6hrs 1days Polyurethane Basecoat 24hrs 7days 16hrs 4days 12hrs 2days 6hrs 1days Trilux 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Trilux 33 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Uni-Pro 24hrs 48hrs 10hrs 20hrs 6hrs 16hrs 4hrs 10hrs Note:If maximum overcoating time is exceeded, sand with 180-220 grade wet or dry paper.
    [Show full text]
  • Interfill 830 Fast Cure Fillers Epoxy Profiling Filler
    Interfill 830 Fast Cure Fillers Epoxy Profiling Filler PRODUCT DESCRIPTION Interfill 830 Fast Cure is the best choice for profiling above and below the waterline on Steel, Aluminium and Composite hulls. The special 2-component light grey epoxy formulation can fill up to a thickness of 1 inch in one coat without the risk of sagging/slumping. * Fast curing at lower temperatures * Low density composition * High strength and impact resistance * Easy sanding * Waterproof When sanded, the surface of the Interfill 830 Fast Cure is smooth enough to be directly overcoated with Interprime 820 high build epoxy primer or Interprime 880. Interfill 830 Fast Cure is particularly suitable for application over large areas at low temperatures and also for filling smaller areas when rapid sanding or overcoating is required. PRODUCT INFORMATION Colour YAA867 Finish Matt Specific Gravity 0.74 Volume Solids 91% Mix Ratio 1:1 by volume (as supplied) . Mix ratio by weight: 1.17:1 YAA867:YAA869 Converter/Curing Agent YAA869 Typical Shelf Life 2 yrs VOC (As Supplied) 94 g/lt Unit Size 5 Lt 20 Lt DRYING/OVERCOATING INFORMATION Drying 10°C (50°F) 15°C (59°F) 23°C (73°F) 35°C (95°F) Sandable 16 hrs 16 hrs 6 hrs 3 hrs Pot Life 50 mins 45 mins 35 mins 20 mins Overcoating Substrate Temperature 10°C (50°F) 15°C (59°F) 23°C (73°F) 35°C (95°F) Overcoated By Min Max Min Max Min Max Min Max Interfill 835 24 hrs - 24 hrs - 6 hrs - 6 hrs - Interprime 820 24 hrs - 24 hrs - 6 hrs - 6 hrs - Interprime 880 24 hrs - 24 hrs - 6 hrs - 6 hrs - Interprotect 24 hrs - 24 hrs - 6 hrs - 6 hrs - Interprotect (Professional) 24 hrs - 24 hrs - 6 hrs - 6 hrs - Note: Once the sandable time has been exceeded, all fillers should be sanded before overcoating to promote good adhesion.
    [Show full text]
  • Interprime® 234 Alkyd PRODUCT a One Component, High Build Alkyd Primer Containing Anticorrosive Pigment
    Interprime® 234 Alkyd PRODUCT A one component, high build alkyd primer containing anticorrosive pigment. DESCRIPTION INTENDED USES For use as a general purpose maintenance primer primarily for the bridge market, for application to correctly prepared steel. PRACTICAL Color Red, Off White, Gray INFORMATION FOR INTERPRIME 234 Gloss Level Matte Volume Solids 58% ± 2% Typical Thickness 1.5-3.6 mils (38-89 microns) dry equivalent to 2.6-6.1 mils (66-153 microns) wet Theoretical Coverage 465 sq.ft/US gallon at 2 mils d.f.t and stated volume solids 11.60 m²/liter at 50 microns d.f.t and stated volume solids Practical Coverage Allow appropriate loss factors Method of Application Airless Spray, Roller, Brush, Conventional Spray Drying Time Overcoating Interval with recommended topcoats Temperature Touch Dry Hard Dry Minimum Maximum 41°F (5°C) 2 hours 16 hours 20 hours Extended¹ 50°F (10°C) 2 hours 12 hours 12 hours Extended¹ 77°F (25°C) 90 minutes 6 hours 6 hours Extended¹ 95°F (35°C) 30 minutes 5 hours 5 hours Extended¹ ¹ See International Protective Coatings Definitions & Abbreviations REGULATORY DATA Flash Point 99°F (37°C) Product Weight 12.6 Ib/gal (1.51 kg/l) VOC 2.83 lb/gal (340 g/lt) EPA Method 24 See Product Characteristics section. Protective Coatings Page 1 of 4 Issue Date:3/9/2010 Ref:2352 Interprime® 234 Alkyd SURFACE All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application, all PREPARATION surfaces should be assessed and treated in accordance with ISO 8504-2000.
    [Show full text]
  • July 2020 Publication Date : 6 July 2020 No
    STRIKING OFF FINAL GAZETTE NOTIFICATION The following companies were struck off from the Register of Companies with effect from: Struck Off Date : 6 July 2020 Publication Date : 6 July 2020 No. of Companies : 2262 No. UEN Company Name 1 201705985W GUARDFORCE INVESTMENT HOLDINGS (SINGAPORE) PTE. LTD. 2 201635164R JEAUL PTE. LTD. 3 200010208M VARUNSOFT PTE LTD 4 201730402D HORIZON INNOVATION CATALYSTS PTE. LTD. 5 201808845E BI FINTECH PTE. LTD. 6 201433959N THE BLIND COBBLER PTE. LTD. 7 199402944R YEOH SWEE INN ENDOCRINE AND MEDICAL CLINIC PTE LTD 8 201618244W CK CONSTRUCTORS & ENGINEERING PTE. LTD. 9 201812391M DYNAMIC FINTECH GROUP PTE. LTD. 10 201804369R SOCIAL LENDING NETWORK FOUNDATION LTD. 11 201900454C 3 ELEMENZ HOLDINGS PTE. LTD. 12 201524039Z EON FOOD TECH PTE. LTD. 13 200810152E MOOINC. PTE. LTD. 14 201005061M BUKIT BARISAN PTE. LTD. 15 200511931K EPIC SHIPPING PTE. LTD. 16 201608832M WOODLANDS AUTO CAR RENTAL PTE. LTD. 17 201538826N GTOF TWO HOLDINGS PTE. LTD. 18 201504443H PLAWORKS PTE. LTD. 19 201633696R ADDEEN PTE. LTD. 20 201904747K CRESCERE INFINITE CAPITAL PTE. LTD. 21 201724196E BLUE SAND V PTE. LTD. 22 201629660M BH AUTO TRADING PTE. LTD. 23 201725212K CK TRADING PTE. LTD. 24 199405178K SANTEC INDUSTRIES (S) PTE LTD 25 201910325W HMLET TOWNSHIP 5 PTE. LTD. 26 201837894R HUI YING INVESTMENT PTE. LTD. 27 201708646D DPCF MANAGEMENT CONSULTANTS PTE. LTD. 28 200913741C AQ WEALTH PARTNERS PTE. LTD. 29 201535201W ARK FLOWERS PTE. LTD. 30 201006646E SAKAE SUSHI (SCAPE) PTE. LTD. 31 201903171Z GOLDEN SIERRA LIGHTS PTE. LTD. 32 201623503R RUHI SOLUTIONS PTE. LTD. 33 200607965R E. S. R. INTERNATIONAL PTE. LTD.
    [Show full text]
  • Interfill 830
    Interfill 830 Interfill 830 Fillers Epoxy Profiling Filler PRODUCT DESCRIPTION Interfill 830 is the best choice for profiling above and below the waterline on Steel, Aluminium and Composite hulls. The special 2- component light grey epoxy formulation can fill up to a thickness of 1 inch in one coat without the risk of sagging/slumping. * Low density composition * High strength and impact resistance * Easy sanding * Waterproof When sanded, the surface of the Interfill 830 is smooth enough to be directly overcoated with Interprime 820 high build epoxy primer. Interprotect or Interprime 880 may also be used. Interfill 830 is particularly suitable for application over large areas. PRODUCT INFORMATION Colour YAA867 Finish Matt Specific Gravity 0.75 Volume Solids 92.61% Mix Ratio Mix ratio by weight: 1.15:1 YAA867: YAA868, Converter/Curing Agent - YAA868 Typical Shelf Life 2 yrs VOC (As Supplied) 77 g/lt Unit Size 5 Lt 20 Lt DRYING/OVERCOATING INFORMATION Drying 10°C 15°C 23°C 35°C Sandable 48hrs 28hrs 19hrs 13hrs Pot Life 75mins 55mins 45mins 20mins Overcoating Substrate Temperature 10°C 15°C 23°C 35°C Overcoated By Min Max Min Max Min Max Min Max Interfill 835 5days - 3days - 2days - 1days - Interprime 820 5days - 3days - 2days - 1days - Interprime 880 5days - 3days - 2days - 1days - Interprotect (Professional) 5days - 3days - 2days - 1days - Note:Once the sandable time has been exceeded, all fillers should be sanded before overcoating to promote good adhesion. A sanded filler may be left for a period up to 3 months before being overcoated with further epoxy filler or with Interprime 8-series.
    [Show full text]
  • Colour Card Our Most Popular Colours Pearl Grey H017 Pebble Grey J019 Mist Grey F000 Dawn Grey E000 Blued White C000 Gardenia B052
    International Paint Ltd is part of AkzoNobel, the Netherlands based Blue Grey M400 Dove Grey M319 Westmorland Grey J300 Silver Grey H001 Flotilla H000 Hemp J071 company serving customers throughout the world with coatings and chemicals. Colour Card Our most popular colours Pearl Grey H017 Pebble Grey J019 Mist Grey F000 Dawn Grey E000 Blued White C000 Gardenia B052 International Paint Ltd, Stoneygate Lane, Felling Oyster White E019 Vanilla B088 Stone D053 Cream S089 Yellow S041 Cream B108 Gateshead, NE10 0JY United Kingdom Call: +44 (0)191 469 6111 Fax: +44 (0)191 495 2003 Golden Yellow B169 Yellow B134 Canary C065 Golden Yellow B183 Buff E143 Primrose G164 Send an email: [email protected] Visit our website: www.international-marine.com Sign up to keep up to date with our latest news visit www.international-marine.com/signup Sand B125 Beige H108 Orange E229 Light Orange D243 Pure Orange D259 Funnel Orange Y74R Follow us 10 0 Mink D104 Red Buff G194 International Orange D260 Signal Red C287 Ensign Red B295 Teak M231 The contents of this card are for information purposes only and no representation or warranty of any kind is given in relation to any of the information or opinions expressed in it. Whilst we have made all reasonable efforts to ensure that statements appearing in this leaflet are accurate, we disclaim all liability and responsibility arising from any reliance placed on the information, advice and opinions contained in this leaflet. and International and all products mentioned in this publication are trademarks Brown T229 Brown R244 Red Brown P275 Copper Beech M254 Red L274 Red M273 ® of, or are licensed to, AkzoNobel.
    [Show full text]
  • Interprime 198 Alkyd Primer
    Interprime 198 Alkyd Primer PRODUCT DESCRIPTION A quick drying, one pack primer. Interprime 198 is surface tolerant, compatible with most substrates and can be overcoated with a wide range of finishes. INTENDED USES For the maintenance of above water areas. Approved for the carriage of grain when used as part of an approved scheme. For use at Maintenance & Repair or On Board Maintenance. PRODUCT INFORMATION Colour CPA097-White, CPA098-Grey, CPA099-Red Finish/Sheen Matt Part B (Curing Agent) Not applicable Volume Solids 41% ±2% (ISO 3233:1998) Mix Ratio Not applicable Typical Film Thickness 75 microns dry (183 microns wet) Theoretical Coverage 5.47 m²/litre at 75 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush, Roller Flash Point (Typical) Single Pack 35°C Drying Information -5°C 5°C 25°C 35°C Touch Dry [ISO 9117/3:2010] 8 hrs 3 hrs 60 mins 30 mins Hard Dry [ISO 9117-1:2009] 48 hrs 24 hrs 4 hrs 2 hrs Overcoating Data - see limitations Substrate Temperature -5°C 5°C 25°C 35°C Overcoated By Min Max Min Max Min Max Min Max Interfine 5703 - - - - 2 hrs 3 days 2 hrs 24 hrs Interfine 599 - - 9 hrs 3 days 3 hrs 2 days 60 mins 24 hrs Interlac 665 24 hrs 3 days 6 hrs 3 days 2 hrs 2 days 60 mins 24 hrs Interprime 198 8 hrs ext 3 hrs ext 60 mins ext 30 mins ext Intersheen 579 24 hrs 3 days 24 hrs 3 days 12 hrs 2 days 6 hrs 24 hrs Interstores Alkyd - - 6 hrs 3 days 2 hrs 2 days 60 mins 24 hrs Interstores Polyurethane - - 24 hrs 7 days 12 hrs 7 days 6 hrs 3 days Interthane 990 - - 24 hrs 7 days 12 hrs 7 days 6 hrs 3 days Intertherm 891 24 hrs 28 days 6 hrs 28 days 2 hrs 28 days 60 mins 28 days REGULATORY DATA VOC 506 g/lt as supplied (EPA Method 24) 416 g/kg of liquid paint as supplied.
    [Show full text]
  • About the Author and This Text
    1 PHUN WITH DIK AND JAYN BREAKING RSA CODES FOR FUN AND PROFIT A supplement to the text CALCULATE PRIMES By James M. McCanney, M.S. RSA-2048 has 617 decimal digits (2,048 bits). It is the largest of the RSA numbers and carried the largest cash prize for its factorization, US$200,000. The largest factored RSA number is 768 bits long (232 decimal digits). According to the RSA Corporation the RSA-2048 may not be factorable for many years to come, unless considerable advances are made in integer factorization or computational power in the near future Your assignment after reading this book (using the Generator Function of the book Calculate Primes) is to find the two prime factors of RSA-2048 (listed below) and mail it to the RSA Corporation explaining that you used the work of Professor James McCanney. RSA-2048 = 25195908475657893494027183240048398571429282126204032027777 13783604366202070759555626401852588078440691829064124951508 21892985591491761845028084891200728449926873928072877767359 71418347270261896375014971824691165077613379859095700097330 45974880842840179742910064245869181719511874612151517265463 22822168699875491824224336372590851418654620435767984233871 84774447920739934236584823824281198163815010674810451660377 30605620161967625613384414360383390441495263443219011465754 44541784240209246165157233507787077498171257724679629263863 56373289912154831438167899885040445364023527381951378636564 391212010397122822120720357 jmccanneyscience.com press - ISBN 978-0-9828520-3-3 $13.95US NOT FOR RESALE Copyrights 2006, 2007, 2011, 2014
    [Show full text]
  • Laser Spectroscopy for Rapid Profiling of Steel Bridge Coating, Corrosion, and Heavy Metals
    NCHRP IDEA Program Laser Spectroscopy for Rapid Profiling of Steel Bridge Coating, Corrosion, and Heavy Metals Final Report for NCHRP IDEA Project 164 Prepared by: Warren H Chesner, Chesner Engineering P.C. Nancy J. McMillan, New Mexico State University May 2015 Innovations Deserving Exploratory Analysis (IDEA) Programs Managed by the Transportation Research Board This IDEA project was funded by the NCHRP IDEA Program. The TRB currently manages the following three IDEA programs: • The NCHRP IDEA Program, which focuses on advances in the design, construction, and maintenance of highway systems, is funded by American Association of State Highway and Transportation Officials (AASHTO) as part of the National Cooperative Highway Research Program (NCHRP). • The Safety IDEA Program currently focuses on innovative approaches for improving railroad safety or performance. The program is currently funded by the Federal Railroad Administration (FRA). The program was previously jointly funded by the Federal Motor Carrier Safety Administration (FMCSA) and the FRA. • The Transit IDEA Program, which supports development and testing of innovative concepts and methods for advancing transit practice, is funded by the Federal Transit Administration (FTA) as part of the Transit Cooperative Research Program (TCRP). Management of the three IDEA programs is coordinated to promote the development and testing of innovative concepts, methods, and technologies. For information on the IDEA programs, check the IDEA website (www.trb.org/idea). For questions, contact the IDEA programs office by telephone at (202) 334-3310. IDEA Programs Transportation Research Board 500 Fifth Street, NW Washington, DC 20001 The project that is the subject of this contractor-authored report was a part of the Innovations Deserving Exploratory Analysis (IDEA) Programs, which are managed by the Transportation Research Board (TRB) with the approval of the National Academies of Sciences, Engineering, and Medicine.
    [Show full text]
  • Determinants of Multiple Semantic Priming: a Meta-Analysis and Spike Frequency Adaptive Model of a Cortical Network
    Determinants of Multiple Semantic Priming: A Meta-analysis and Spike Frequency Adaptive Model of a Cortical Network Frédéric Lavigne, Laurent Dumercy, and Nelly Darmon Abstract ■ Recall and language comprehension while processing se- stimuli onset asynchronies on the pattern of underadditivity, quences of words involves multiple semantic priming between overadditivity, or strict additivity of converging activation from several related and/or unrelated words. Accounting for multiple multiple primes. The modeling approach is then constrained by and interacting priming effects in terms of underlying neuronal results of the meta-analysis. We propose a model of a cortical structure and dynamics is a challenge for current models of se- network embedding spike frequency adaptation, which allows mantic priming. Further elaboration of current models requires frequency and time-dependent modulation of neural activity. a quantifiable and reliable account of the simplest case of multiple Model results give a comprehensive understanding of the meta- priming resulting from two primes on a target. The meta-analytic analysis results in terms of dynamics of neuron populations. They approach offers a better understanding of the experimental data also give predictions regarding how stimuli intensities, associa- from studies on multiple priming regarding the additivity pattern tion strength, and spike frequency adaptation influence multiple of priming. The meta-analysis points to the effects of prime–target priming effects. ■ INTRODUCTION ing up the challenge requires identification of cognitive, Language comprehension involves contextual recall of procedural, and cellular factors that determine the balance knowledge in memory in real time. This fundamental between priming from previous and from current words in cognitive function relies on the increased availability of a sequence and that direct semantic activation within the concepts in memory due to activation of other concepts semantic space.
    [Show full text]