SW4-OPT-TX240RAK Quick Start Guide

Total Page:16

File Type:pdf, Size:1020Kb

SW4-OPT-TX240RAK Quick Start Guide Front View Audio Source LEDs 1 2 3 4 5 6 789q we OFF: audio source is not selected. BLINKING: audio source is selected but no signal is detected (digital inputs only). ON: (with short pause): audio source is selected and the port is active but not embedded to the output video stream (DVI output mode). ON: (continuously): audio source is selected, the port is active and the audio is embedded to the output video stream (HDMI output mode). When Autoselect is enabled and video signal is not present at all, video LEDs blink. 1 HDCP status LED shows the actual HDCP status of the video output. 9 Reset button Pushing the button reboots the unit. HDCP LED LED OFF: video output signal is not encrypted with HDCP. q Audio select button Button for switching between audio sources. 2 USB port USB interface for USB KVM function, firmware upgrade, and ON: video output signal is encrypted with HDCP. LDC software control purposes. w Audio2 status LED LED gives feedback about actual connection status of Autoselect LED Audio2 input port (on the rear side of device) 3 DisplayPort Connect a DisplayPort cable between the DisplayPort source OFF: Autoselect is disabled. input and the transmitter unit. e Show Me button Special functions are available with this button (bootload BLINKING: Autoselect function is enabled, searching for signal (the video input LEDs are 4 HDMI input Connect an HDMI cable between the HDMI source and the mode, DHCP, restore factory default settings). also blinking). ports transmitter unit. ON: Autoselect function is enabled, the active video signal is found (the selected video Quick Start Guide input’s LED is also ON). 5 DVI-D input DVI-I connector for HDMI or DVI-D signal. Front Panel LEDs USB LED SW4-OPT-TX240RAK 6 Audio1 input 3.5mm Jack connector for unbalanced analog audio input signal. Video Source LEDs OFF: USB is disconnected or there is no USB data transfer over the port. 7 Video select Button for switching between video sources. ON (green): USB KVM: composite mode is active. OFF: video source is not selected. ON (yellow): USB KVM: transparent mode is active. 8 Autoselect LED gives feedback about the actual status of the video BLINKING: video source is selected but no signal is detected. status LED autoselect function. ON: video source is selected and active. Important Safety Instructions Rear View Rear Panel LEDs Please read and keep the information in the attached safety instructions supplied with the 1 2 3 4 5 6 7 8 LIVE product before you start using the device. LIVE OFF: device is not powered. LASER ACTIVE The transmitter is a Class 3R laser product. Caution! Invisible Class 3R laser BLINKING (green): device is powered and operational. FIBER LINK radiation! Avoid exposure to the beam! RS-232 BLINKING (red): alert detected. Introduction BLINKING (yellow): firmware upgrade mode, device is in bootload mode. Thank You for choosing Lightware SW4-OPT-TX240RAK transmitter. The product is a multi- ON (yellow): device is powered but no operation. mode single fiber extender with bidirectional RS-232 extension. The device transmits DP / HDMI / DVI digital video signals up to 4K resolution, 3D and HDCP compliant and is able to LASER ACTIVE 1 SC fiber output Connect a multi-mode single fiber optical cable between the 5 Status LEDs LEDs give feedback about actual status of unit and embed analog audio from 3.5mm TRS (Jack) or 5-pole balanced Phoenix type ports. The LIVE ON (red): laser transmission is enabled. receiver and the transmitter. connection signals. transmitter is built with USB KVM function. The device features Pixel Accurate Reclocking, LASER ACTIVE FIBER LINK a Lightware technology to eliminate jitter and skew generated by low quality sources and 2 Audio2 input 5-pole Phoenix connector for balanced analog audio input. 6 GPIO 8-pole Phoenix connector for configurable general purpose RS-232 input/output ports. multiple daisy-chained devices. 3 HDMI output Connect an HDMI cable between the transmitter and the display device. 7 RS-232 3-pole Phoenix connector for serial communication. FIBER LINK OFF: no fiber link between transmitter and receiver. 4 Ethernet RJ45 connector to remote control the transmitter via LAN 8 5V DC input Connect the output of the supplied 5V DC power adaptor. LIVE LASER ACTIVE ON: fiber link is established. Box Contents network. FIBER LINK RS-232 Video/Audio Input Selection Front Panel Button Functions RS-232 Desired video/audio input can be selected by the VIDEO / AUDIO SELECT buttons on the Video input switching: Press the VIDEO SELECT button. LIVE OFF: RS-232 ports (local and link) are in Pass-through mode. LASER ACTIVE front panel. The selection order of the video inputs is the following: Audio input switching: Press the AUDIO SELECT button. BLINKING: Command injection mode is active. FIBER LINK Transmitter unit 5V DC adaptor with Phoenix Combicon 3-pole D D D DD toselet Lock/unlock buttons: Press the AUDIO SELECT and the SHOW ME buttons together. RS-232 ON: RS-232 ports (local and link) are in Control mode. interchangeable plugs connector Connecting Steps OPTM Connect the transmitter and the compatible receiver or matrix input board Further information Saet and Quick aant Stat using a multimode single fiber optical cable. de The document is valid with the following firmware version: 1.1.0 no MacBook Blu-ray player PC MP3 Media Local DP The product brief and further information are available at www.lightware.eu. player player monitor Connect the source(s) (e.g. a MacBook / Blu-ray player / PC) to the input HDMI port(s) of the transmitter by a DP / DVI-D / HDMI cable(s). See the Downloads section on the website of the product. Phoenix Combicon 5-pole Phoenix Combicon 8-pole Safety and warranty info, DVI-D connector connector Quick Start Guide Audio Optionally connect an assymmetric audio device with unbalanced audio Contact us signal (e.g. an MP3 player) to the 2.5” TRS (jack) audio input port. DP HDMI DVI-D Audio Audio HDMI [email protected] Mounting Audio Optionally connect a symmetric audio device with balanced audio signal (e.g. +36 1 255 3800 To mount the transmitter Lightware supplies optional accessories for different usage. There a professional media player) to the 5-pole Phoenix audio input port. are two kinds of mounting kits with similar fixing method. The transmitter has two mounting SW4-OPT-TX240RAK HDMI Connect the local sink device (e.g. a monitor) to the HDMI output port by an [email protected] : holes with inner thread on the bottom side. Fasten the device by the screws enclosed to the : transmitter HDCP VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO1 Autoselect AUDIO2 OPTM HDMI cable. +36 1 255 3810 USB AUDIO RST VIDEO AUDIO SHOW accessory. 1 DP IN 2 HDMI1 IN 3 HDMI2 IN 4 DVI-D IN 5 AUDIO1 IN SELECT SELECT ME Compatible USB Optionally for USB HID extension: connect the transmitter to the computer by the receiver USB mini B-type cable. Lightware Visual Engineering LLC. Power GPIO LAN USB RS-232 RS-232 Optionally for RS-232 control: connect a controller/controlled device (e.g. a touch Peterdy 15, Budapest H-1071, Hungary Under-desk double mounting kit 1U high rack shelf panel) to the RS-232 port. LAN Optionally connect the switcher to a LAN network in order to control the device. Doc. ver.: 1.1 The Under-desk double mounting kit makes it easy to mount a single device on any flat 19200061 surface, e.g. furniture. 1U high rack shelf provides mounting holes for fastening two half-rack GPIO Optionally connect a controller/controlled device (e.g. relay box) to the GPIO port. or four quarter-rack sized units. Pocket-sized devices can also be fastened on the shelf. To order mounting accessories please contact [email protected]. Power Relay Ethernet PC Touch Power Connect the power adaptor to the DC input on the transmitter first, then to the AC power socket. The transmitter is half-rack sized. adaptor box panel Optical Extender Concept Typical Application GPIO - General Purpose Input/Output Ports HDMI-3D-OPT-RX150RA SW4-OPT-TX240RAK has a multi-mode single fiber output interface which is able to transmit Integrated system diagram RS-232 SW4-OPT-TX240RAK transmitter has seven GPIO pins which operate at TTL digital signal different type of signals at the same time. The device accepts digital video (DP, HDMI, and levels and can be set to high or low level (Push-Pull). The direction of the pins can be input or DVI-D) and analog audio sources (Jack and 5-pole Phoenix). The unit can be controlled over output (adjustable). Voltage ranges for GPIO inputs are the following: LAN, RS-232 (3-pole Phoenix), and USB interfaces, and is able to control third-party devices 5V DC Input voltage (V) Max. current (mA) using the built-in GPIO ports. Besides of these the transmitter also has USB KVM function. Power HDMI One audio (original embedded or analog) and one video signals can be transmitted via the adaptor Logical low level 0 - 0,8 30 optical output at the same time. .A L P Logical high level IN C 2 - 5 18 HD HDMI Projector GLE SN TIVE AC P AS C L HD I IN HDM PRST HDCP L MI G HD SN SCDT INPUT OUTPUT +5V L.A P IN HDC GPIO connector and plug pin assignment: HDMIGLE SN E TIV MX-FR17 Single fiber multimode AC ER LAS HDCPI IN HDM PRST AL OU IGN S INPUT R ACTIVE 8 SE P LA HDC NT OU HDMIES IN PR GLE DP / HDMI / DVI-D HDMI / DVI-D U SN INP VE optical cable up to 2500m TI AC T LASDCP OU H MI T IN HD PRS : LE SNG : Level and R ACTIVE SE P LA HDC IN HDMI PRST E Analog audio Analog audio V SGNAL Pin nr.
Recommended publications
  • DM-TX-300N Digitalmedia™ CAT Transmitter 300N
    DM-TX-300N DigitalMedia™ CAT Transmitter 300N > DigitalMedia™ CAT transmitter and multimedia interface > Built-in 3x1 AV switcher with front panel input selection and audio-breakaway[3] > QuickSwitch HD® technology achieves fast, reliable switching > DM® CAT output supports up to 450 ft (137 m) cable length[1] > Provides HDMI®, DVI, RGB, and multi-format analog video inputs > Also supports DisplayPort Multimode sources[4] > Includes balanced/unbalanced analog and S/PDIF audio inputs > Includes a local HDMI monitor output Multimedia Computer/AV Interface > Handles HD video with HDCP The DM-TX-300N provides versatile switching among three different video and audio sources. The inputs can be selected manually from the front > Handles Dolby Digital®, DTS®, and uncompressed 7.1 linear PCM audio panel or through a Crestron control system. Inputs include: > Detects and reports detailed video and audio input information • HDMI — Supports HD 1080p60 video and WUXGA computer signals > Performs automatic AV signal format management via EDID with HDCP and multi-channel lossless audio. Also handles DisplayPort > Provides a 10/100 Ethernet connection Multimode signals using an appropriate adapter or interface cable. > Enables device control via CEC, IR, RS-232, and Ethernet • DVI-I — This input handles DVI and analog RGB signals up to WUXGA > Allows quick, easy setup and diagnostics 1920x1200 pixels, as well as analog video up to 1080p60[2]. A stereo > Single-space 19-inch rack-mountable audio input is included to accommodate the analog audio signal from a > Includes external universal power pack balanced or unbalanced line-level source. • Video — This multi-format video input accepts analog YPbPr The DM-TX-300N is a DM® CAT transmitter and switcher that offers a component video signals up to 1080p60, as well as standard definition NTSC/PAL composite and S-Video.
    [Show full text]
  • Multi-Purpose Consoles Spirit Range Brochure
    MULTI-PURPOSE CONSOLES FX16 16 Mono Channels with onboard Lexicon Effects FX8 8 Mono Channels with onboard Lexicon Effects SX SPIRIT RANGE 12 Mono & 4 Stereo Inputs BROCHURE M SERIES 4/8/12 Mono & 4 Stereo Inputs E SERIES 6 or 8 Mono & 4 Stereo Inputs NOTEPAD 4 Mono & 2 Stereo Inputs CONTENTS Quick Selector Compare Spirit Mixer Inputs & Features Quickly Features Table Page 4 Spirit Mixers at a glance 4 ? Power Features What makes Spirit consoles special Features in depth Pages 4 - 7 Power Features 4 - 7 FX16 16 Mono Channels with onboard Lexicon Effects Full Product Description Pages 8 & 9 The Mixers in detail 8 - 18 Dimensions Page 24 Specifications Page 25 FX8 8 Mono Channels with onboard Lexicon Effects Full Product Description Pages 10 & 11 Dimensions Page 24 Specifications Page 25 sx 12 Mono & 4 Stereo Inputs Full Product Description Pages 12 & 13 Dimensions Page 24 Specifications Page 25 M Series 4/8/12 Mono & 4 Stereo Inputs Full Product Description Pages 14 & 15 Dimensions Page 24 Specifications Page 25 E Series 6 or 8 Mono & 4 Stereo Inputs Full Product Description Pages 16 & 17 Dimensions Page 24 Specifications Page 25 Notepad 4 Mono & 2 Stereo Inputs Full Product Description Page 18 Dimensions Page 24 Specifications Page 25 Applications Using Spirit Mixers in Various Situations Introduction Page 19 Mic/Line Live Mixing Page 20 Insert Houses of Worship Page 21 Installed Sound Page 21 Mic/Line Mixer Applications 19 - 23 Submixing Page 22 Mic/Line Video Editing Page 22 Small/Home Studio Page 22 Dimensions & 24 - 25 Mic/Line Studio Recording Page 23 Specifications Mic/Line Frequently Asked 26 Other Soundcraft Products Questions How to find out more See Back Cover Glossary of 27 Technical Terms Other Soundcraft back cover products 2 WORLD CLASS MIXERS TEXAS When the Spirit range was first launched, mixing desks were either large and expensive, or small but ineffective.
    [Show full text]
  • Audio Electrical Wiring Considerations Basic Branch Circuits in Homes And
    EELE 217 Science of Sound 2017 1 Audio Electrical Wiring Considerations Basic branch circuits in homes and businesses (U.S.) Service Panel Black Wire ("hot") Circuit Breaker (from power company and White Wire (wide) power meter) (neutral) (narrow) Ground Bus Bar Green or Bare Wire Cold Water Pipe (protection ground) IF the outlet is wired correctly (never EVER risk your life on this assumption!!), the white wire ("neutral") should be the wide blade and the electrical potential should be near zero potential. In the U.S. the black wire ("hot") is 120 volts RMS (root-mean-square) sinusoid, 60 Hz repetition frequency, with peaks ±170 volts respect to the neutral. Keep in mind that the colors are purely customary: the color itself doesn't influence how the electricity flows in the circuit! The green (or bare) wire is the protection ground, and the internal wiring of an appliance will have this conductor connected it to the metal chassis of the appliance. The green wire does not conduct any current under normal circumstances, EXCEPT if there is a fault in the appliance that allows the "hot" wire to come in contact with the chassis. In the case of a fault the ground wire short circuits the "hot" wire through the chassis and back to ground, which should draw enough current to trigger the circuit breaker to open, de-energizing the outlet. This protection is important, because without it a fault could energize the chassis, and then a person could get shocked by simultaneously touching the chassis and a nearby grounded surface, inadvertently completing the circuit.
    [Show full text]
  • How to Choose the Right Cable
    Choosing the Right ProX Cable for Your Needs Unbalanced vs. Balanced Cables First thing to know about microphone cables, XLR is a CONNECTOR, not a cable although often called an XLR cable incorrectly. A more correct description would be “Audio Cable with XLR”. A balanced electrical signal runs along three wires: a ground, a positive leg, and a negative leg. Both legs carry the same signal but in opposite polarity to each other. Any noise picked up along the cable run will typically be common to both legs. Assuming the destination is balanced, the receiving device will “flip” one signal and put the two signals back into polarity with each other. This causes the bulk of the common noise to be out of phase with itself, thus being eliminated. This noise cancellation is called “Common Mode Rejection” and is the reason balanced lines are generally best for long cable runs. XLR Audio and TRS cables are used to transmit balanced audio from one balanced device to another. If you are experiencing noise on a balanced cable, it could be caused by incorrectly wired cables. Unbalanced cables are less complicated, but they’re much more susceptible to noise problems. In general, unbalanced lines should be kept as short as possible (certainly under 25 feet) to minimize any potential noise that may be carried with the signal into the connected equipment. Understanding Common Cable Connectors In the audio world, there are six common cable connectors you’ll come across frequently: TRS and XLR for balanced connections and TS, RCA, SpeakON, and banana plugs for unbalanced connections.
    [Show full text]
  • Power and Grounding for Audio and Audio/Video Systems a White Paper for the Real World Jim Brown the Audio Systems Group, Inc
    Power and Grounding for Audio and Audio/Video Systems A White Paper for the Real World Jim Brown The Audio Systems Group, Inc. http://audiosystemsgroup.com Considerable confusion seems to surround power and grounding for audio and audio/video systems. This “White Paper” is an attempt to cut through the confusion and set out a col- lection of good engineering practice that is both safe and effective. The author believes that the recommendations and practices outlined herein are safe, and that they conform to building codes in most of North America. The author is an electrical engineer by training and an audio systems consultant by profession, but is not a registered Professional Engi- neer. No warranty is made or implied as to the extent to which these practices conform to local codes or regulations. Qualified professional engineers and electrical contractors should design and install all electrical systems. AUDIO AND VIDEO SYSTEM POWER REQUIREMENTS With the exception of a few very large power amplifiers and video projectors, virtually all audio and video equipment sold in North America utilizes single-phase 60 Hz power at 120V. Few individual pieces of equipment require more than 20A; most require far less current. The largest projectors and amplifiers may require 240V, 60 Hz, single phase power, at up to 20A. Most audio and video equipment draws relatively little power. Audio and video equipment falls into two basic categories – small signal equipment and large signal equipment. Small signal equipment amplifies, processes, mixes, routes, and controls the signal. Mix con- soles, crossovers, equalizers, digital signal processors, routers, and switchers are all exam- ples of small signal equipment.
    [Show full text]
  • Device Interconnection
    Device Interconnection An important, if less than glamorous, aspect of audio signal handling is the connection of one device to another. Of course, a primary concern is the matching of signal levels and impedances between the devices, but there are additional considerations. Not only are wire and connectors of differing types involved, the grounding of a device is potentially affected by all the other equipment to which it is connected. Interconnection practices are important because all signals must be transmitted from device to device and noise added in the process can be very difficult to eliminate once it becomes part of the signal. By using properly shielded and grounded connec- tions, a high quality audio signal can be preserved, even in very large systems. While this discussion relates to analog connections, there are similar concerns in digital systems that we will address later. Shielding: Noise sources couple into wires by induction (like a transformer) and by capacitive coupling. These noise signals are produced by the 60 Hz power-lines, by radio transmitters, computers, electric motors, and many other electrical sources present in the environment. Shielding is a method of protecting audio signals from radiated noise by providing a low impedance pathway to ground for the unwanted electromagnetic sig- nals. Audio signals are always transmitted on shielded cable (except for high power, high level, low impedance signals like power amplifier connections to speakers), thereby reducing or eliminating the problem of noise coupling. The shield is usually a braid of copper wire (or metal coated plastic) surrounding the wire or wires that conduct the audio signal.
    [Show full text]
  • AN-16/I V.2 Input Module User Guide Vii Insert Send/Return Points
    A-Net In Mono Stereo Mono Stereo Mono Stereo Mono Stereo Mono Stereo Mono Stereo Mono Stereo Mono Stereo v.2 Power Input Module User Guide 9310 1026 0001F rev 1.1 © 2015 Aviom, Inc. READ THIS FIRST Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time.
    [Show full text]
  • 1 Design of High-Performance Balanced Audio Interfaces
    Design of High-Performance Balanced Audio Interfaces Bill Whitlock Jensen Transformers, Inc. 9304 Deering Avenue Chatsworth, CA 91311 High signal-to-noise ratio is an important goal for most audio systems. However, ac power connections unavoidably create ground voltage differences, magnetic fields, and electric fields. Balanced interfaces, in theory, are totally immune to such interference. For 50 years, virtually all audio equipment used transformers at its balanced inputs and outputs. Their high noise rejection was taken for granted and the reason for it all but forgotten. The transformer’s extremely high common-mode impedance - about a thousand times that of its solid-state “equivalents” - is the reason. Traditional input stages will be discussed and compared. A novel IC that compares favorably to the best transformers will be described. Widespread misunderstanding of the meaning of “balance” as well as the underlying theory has resulted in all-too-common design mistakes in modern equipment and seriously flawed testing methods. Therefore, noise rejection in today’s real-world systems is often inadequate or marginal. Other topics will include tradeoffs in output stage design, effects of non-ideal cables, and the “pin 1 problem.” INTRODUCTION The task of transferring an analog audio signal from one system component to another while avoiding audible contamination is anything but trivial. The dynamic range of a system is the ratio, generally measured in dB, of its maximum undistorted output signal to its residual output noise or noise floor. Fielder has shown that up to 120 dB of dynamic range may be required in high-performance sound systems in typical homes.
    [Show full text]
  • Audio Cables Line Level Speaker Level Digital Level INPUTS SIGNAL PROCESS OUTPUTS
    2011 Audio Cables Line Level Speaker Level Digital Level INPUTS SIGNAL PROCESS OUTPUTS Speakers Microphones Amps Equalizer Effects Amps WEST PENN WIRE Board Equalizer Trak Deck Trak Amps Crossover Bass Driver Disc CDR Matrix Mixer Sampler MIC/ LINE LEVEL CABLES SPEAKER LEVEL CABLES WEST PENN WIRE NON-PLENUM WEST PENN WIRE NON-PLENUM (X) 454 224 225 77291 226 227 77293 C210 C208 WEST PENN WIRE PLENUM WEST PENN WIRE PLENUM D25454 25224B 25225B CABLE WITH CONFIDENCE WEST PENN WIRE DUAL NON PLENUM 25226B 25227B 210454 ANALOG AUDIO CABLES: AUDIO RANGE 20Hz to 20 KHz. 20 Hz- Lowest Audible Frequency 440Hz- A on the piano (A4) 4186Hz- Top key on a Piano (C8) 20KHz- Highest Audible Frequency + Amplitude Time - 1 Second 2 Hz Analog audio is a sin wave with an amplitude, time, and frequency. Analog Audio Level Categories: 1. Microphone Level a. Portable, b. Permanent 2. Line Level a. Professional, b. Consumer 3. Speaker Level a. High Impedance, b. Low Impedance WEST PENN WIRE CABLE WITH CONFIDENCE ANALOG AUDIO CABLES: Decibel-l 1/10th of a Bel- Basic Unit of measure in Audio Signals 1dB is the smallest change detectable by the human ear. -10dB change is subjectively about twice as loud or soft. The Decibel is logarithmic because the human ear is logarithmic in response to sound. A logarithm makes dealing with the audio range of numbers involved in amplifier power, sound levels and mic levels much easier to deal with. Decibel in Audio Applications: dB= 10 log (P1/P2).- P- power dBu- Referenced to volts without regards to Impedance- u- unloaded ( no devices attached) 0dBu is always .775Volts dBm- is refers to a standard level of 1 milliwatt dBV- Voltage referenced to 1 Volt without regards to impedance.
    [Show full text]
  • Product Brief
    miniDSP 10x10 HD Hardware miniDSP 10x10 HD is a versatile multi-channel Digital Signal Processor (DSP) 172MHz - 28/56bit DSP path for analog and digital audio sources. Combining high quality audio algo- 24bit ADC / DAC rithms along with a flexible graphical user interface, the 10x10 HD can be 114dB SNR ADC IC & DAC IC used for multi-way speaker processing or multi-channel equalization (e.g. 7.1 Balanced/Unbalanced analog Inputs and Outputs processing). With balanced & un-balanced audio I/O, the platform easily fits SPDIF/AES-EBU/Toslink Input with the needs of most audio systems. The sturdy powder coated steel enclosure, Sample Rate Converter (ASRC) brushed aluminum front panel and removable rack ears is a perfect match for SPDIF + AES-EBU + Toslink output both consumer (Home AV) or commercial (ProAV) applications. External control On the processing side, the platform ranks high on versatility thanks to our Front panel volume control unique product concept of audio plug-ins. The unit is easily configured on through rotary encoder Mac/PC machines from a responsive and intuitive Graphic User Interface. I.R. remote control for Master volume control and preset recall Once the unit is programmed, control of presets, master volume and digital source selection can be done via the front panel encoder or Infrared (I.R) re- Software Control ceiver without the use of a computer. USB 2.0 interface Plug&Play - No driver required Finally, the miniDSP experience isn’t just another audio product. It’s about WinXP/Vista/7 & Mac compatible joining the ranks of a large audio community with fully integrated tools and Firmware upgradeable for future extensive application notes.
    [Show full text]
  • Audio Product Guide
    Product Guide Audio Design Audio Systems Line Level Audio Wireless Audio www.westpennwire.com 1 Audio Simplified Design: Input Audio - Line Level Signal Processing Output Audio - Speaker Level Microphones Audio Sampler Audio Board Audio Amplifiers Matrix Mixer Equalizers Audio Effects Speakers CrossOver www.westpennwire.com 2 Audio Levels: Line Level / Mic Level Audio: Input Audio Line level is the specified strength of an audio signal used to transmit analog sound between audio components such as CD and DVD players, television sets, audio amplifiers, and mixing consoles. Nominal Levels: A line level describes a line’s nominal signal level as a ratio, expressed in decibels, against a standard reference voltage. The nominal level and the reference voltage against which it is expressed depend on the line level being used. While the nominal levels themselves vary, only two reference voltages are common: decibel volts (dBV) for consumer applications, and decibels unloaded (dBu) for profes­ sional applications. The decibel volt reference voltage is 1 VRMS = 0 dBV.[1] The decibel unloaded reference voltage, 0 dBu, is the AC voltage required to produce 1 mW of power across a 600 Ω impedance (approximately 0.7746 VRMS).[2] This awkward unit is a holdover from the early telephone standards, which used 600 Ω sources and loads, and measured dissipated power in decibel­milliwatts (dBm). Modern audio equipment does not use 600 Ω matched loads, hence dBm unloaded (dBu). The most common nominal level for consumer audio equipment is −10 dBV, and the most common nominal level for professional equipment is +4 dBu (by convention, decibel values are written with an explicit sign symbol).
    [Show full text]
  • Gotham Audio Cables 2016 Catalog
    Gotham Cable® ud A io m @ a h G t ® o o t h G a m h . c english about us ® Franz R. Ammann President of the Gotham Organisation 40 years of Audio Cables Excellence, 58 years ® of Mark of Excellence Since 1976 we have been supplying our superior range of professional Audio Cables to the audio-industry. We kept our range a unique assortment of professional products, not compromising our goal, a cable which meets the professional's demand for worry-free transportation of audio signals. Gotham Audio Cables feature the unique «Double Reussen Shielding concept»; 2 layers of 100 % coverage wound in opposite directions will give superb shielding and 100% coverage even if the cable is bent and constantly moved. One step further, in 2013 we developed another level on shielding, by introducing our exclusive Conductor Shielding concept. Each of the 2- (or 4- at star-quad) conductors is also protected with each a 100% coverage with pure copper wires. Our 11301 and 10561 cables feature also not only Double Reussen Shielding but also Conductor Shielding, which will create best possible shielding and RF protection in the industry available. Back in 1990, we introduced the first digital audio cable for the AES/EBU format (110 ohm balanced cables) and are now recognized as the premier manufacturer of digital audio cables. Today, we even offer a full range of multipair cables for AES/EBU digital audio signals with astonishing performance and flexibility. With our stabilisation strands wound around the 2 conductor we can achieve best possible impedance stability even if the cable is bent or moved.
    [Show full text]