DOCSLIB.ORG

Microwave Processing of Lignocellulosic Biomass for Production of Fuels

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Microwave Processing of Lignocellulosic Biomass for Production of Fuels Microwave processing of lignocellulosic biomass for production of fuels Brigid Anne Lanigan Submitted for the degree of Doctor of Philosophy University of York Department of Chemistry 2010 Abstract Abstract Current environmental issues and resource demands are driving the global development of renewable energy. The work described in this thesis applies green and energy efficient microwave technology to transform lignocellulosic biomass into solid and liquid fuels suitable for application in coal burning power plants or upgrading into transportation fuels. Current thermochemical biofuel production (e.g. pyrolysis and gasification) suffer many drawbacks such as high energy consumption and poor flexibility. Herein, it is shown that by applying novel low temperature microwave processing, fuels can be produced at temperatures up to 190 oC lower than required in equivalent conventional thermal treatments. Studies on the microwave activation of the major components of biomass give insight into the mode of action. 180 oC was identified as the key temperature in the degradation of cellulose. Softening of the amorphous region of cellulose at this temperature enables microwave induced rearrangement increasing the efficiency of microwave interaction resulting in acid catalysed decomposition. It was shown possible to produce high calorific value chars at 150 oC lower than previously expected. A reduction of 100 oC was observed in the degradation temperature of hemicellulose. The technology is versatile, effective on a variety of biomass species, and has a favourable energy balance. In studies on whole biomass, the processing conditions and energy usage were found to be favourable when compared with conventional methods. Chars were produced at low temperatures with increased calorific values and material properties in parallel with high quality bio-oils. Pilot scale trials were also carried out proving the technology to be scalable and open to industrial application. This thesis shows for the first time the possibility to produce biofuels via microwave processing, while operating at temperatures below 300 oC. The impact of these findings is being further investigated at the dedicated microwave facility at the University of York. Contents Table of Contents Chapter 1: Introduction 1 1.1 Project Background .................................................................................. 2 1.2 Project Aims ............................................................................................. 3 1.3 Climate Change ........................................................................................ 4 1.4 Sustainable Development and Green Chemistry ..................................... 5 1.5 Biorefinery Concept ................................................................................. 7 1.6 Biomass composition ............................................................................... 8 1.7 Biomass for Energy Production ............................................................. 11 1.7.1 Biomass for liquid fuel ................................................................... 13 1.7.2 Biomass for solid fuel ..................................................................... 14 1.8 Biomass upgrading for energy production ............................................. 15 1.8.1 Thermochemical upgrading of biomass for energy production ..... 17 1.8.2 Gasification of biomass .................................................................. 18 1.8.3 Pyrolysis of biomass for liquid biofuel production ........................ 19 1.8.4 Torrefaction of biomass ................................................................. 21 1.9 Microwave Chemistry ............................................................................ 23 1.9.1 Microwave treatment of biomass ................................................... 25 1.9.2 Industrial application of microwave processes .............................. 28 1.10 Introduction to work in this thesis ....................................................... 28 1.11 References ............................................................................................ 30 Chapter 2: Microwave treatment of biomass components 33 2.1 Introduction ............................................................................................ 34 2.2 Composition of biomass ........................................................................ 34 2.2.1 Cellulose ......................................................................................... 35 2.2.2 Hemicellulose ................................................................................. 36 2.2.3 Lignin ............................................................................................. 37 2.3 Microwave treatment of biomass ........................................................... 38 2.4 Microwave treatment of cellulose .......................................................... 40 2.4.1 The “microwave-effect” ................................................................. 40 Contents 2.4.2 Effect of power and temperature on char formation ...................... 41 2.4.3 Cellulose char characterisation: Spectroscopic analysis .............. 44 2.4.4 Cellulose char characterisation: Elemental analysis .................... 49 2.4.5 Cellulose char characterisation: Thermal analysis ....................... 51 2.4.6 Cellulose char characterisation: Crystallinity ............................... 53 2.4.7 Isotope exchange studies ................................................................ 55 2.4.8 Discussion ...................................................................................... 56 2.5 Microwave treatment of hemicellulose .................................................. 59 2.5.1 Char formation ............................................................................... 59 2.5.2 Hemicellulose char characterisation: Spectroscopic analysis ...... 60 2.5.3 Structural analysis of hemicellulose: Elemental analysis .............. 62 2.5.4 Hemicellulose char characterisation: Thermal analysis ............... 62 2.5.5 Discussion ...................................................................................... 63 2.6 Microwave treatment of lignin .............................................................. 64 2.7 Conclusion ............................................................................................. 65 2.8 References .............................................................................................. 66 Chapter 3: Production of char through microwave treatment of biomass 69 3.1 Introduction ............................................................................................ 70 3.2 Process development .............................................................................. 70 3.3 Biomass for energy production .............................................................. 71 3.3.1 Dedicated energy crop: Miscanthus x giganteus ........................... 72 3.3.2 Agricultural residue: Wheat straw ................................................. 73 3.3.3 Industrial food waste: Cocoa husk ................................................. 74 3.4 Bio-char formation ................................................................................. 75 3.4.1 Properties of unprocessed biomass ................................................ 75 3.4.2 Bio-char from Miscanthus.............................................................. 76 3.4.3 Bio-char from wheat straw............................................................. 77 3.4.4 Bio-char from cocoa husk .............................................................. 80 3.5 Characterisation of bio-char ................................................................... 80 3.5.1 Miscanthus char ............................................................................. 81 3.5.2 Wheat straw char ........................................................................... 83 Contents 3.5.3 Cocoa husk char ............................................................................. 84 3.6 Fuel Properties ....................................................................................... 86 3.7 Conclusions & Future Work .................................................................. 88 3.8 References .............................................................................................. 90 Chapter 4: Production of bio-oil through microwave treatment of biomass 93 4.1 Introduction ............................................................................................ 94 4.2 Bio-oil from the microwave treatment of biomass ................................ 95 4.2.1 Experimental set-up ........................................................................ 96 4.2.2 Microwave treatment of wheat straw for production of bio-oil ....97 4.2.3 Properties of wheat straw bio-oil ................................................... 98 4.2.4 Composition of wheat straw microwave bio-oil ........................... 100 4.2.5 Influence of additives on microwave bio-oil ................................ 102 4.2.6 Influence of additives on bio-oil composition .............................. 104 4.3 Conclusions & Further work ................................................................ 109 4.5 References ............................................................................................ 111 Chapter 5: Short term studies 113 5.1 Introduction .........................................................................................
Load more

Recommended publications
  • What Is Still Limiting the Deployment of Cellulosic Ethanol? Analysis of the Current Status of the Sector
    applied sciences Review What is still Limiting the Deployment of Cellulosic Ethanol? Analysis of the Current Status of the Sector Monica Padella *, Adrian O’Connell and Matteo Prussi European Commission, Joint Research Centre, Directorate C-Energy, Transport and Climate, Energy Efficiency and Renewables Unit C.2-Via E. Fermi 2749, 21027 Ispra, Italy; [email protected] (A.O.); [email protected] (M.P.) * Correspondence: [email protected] Received: 16 September 2019; Accepted: 15 October 2019; Published: 24 October 2019 Abstract: Ethanol production from cellulosic material is considered one of the most promising options for future biofuel production contributing to both the energy diversification and decarbonization of the transport sector, especially where electricity is not a viable option (e.g., aviation). Compared to conventional (or first generation) ethanol production from food and feed crops (mainly sugar and starch based crops), cellulosic (or second generation) ethanol provides better performance in terms of greenhouse gas (GHG) emissions savings and low risk of direct and indirect land-use change. However, despite the policy support (in terms of targets) and significant R&D funding in the last decade (both in EU and outside the EU), cellulosic ethanol production appears to be still limited. The paper provides a comprehensive overview of the status of cellulosic ethanol production in EU and outside EU, reviewing available literature and highlighting technical and non-technical barriers that still limit its production at commercial scale. The review shows that the cellulosic ethanol sector appears to be still stagnating, characterized by technical difficulties as well as high production costs.
    [Show full text]
  • Heat and Mass Transfer During Lignocellulosic Biomass Torrefaction: Contributions from the Major Components—Cellulose, Hemicellulose, and Lignin
    processes Article Heat and Mass Transfer during Lignocellulosic Biomass Torrefaction: Contributions from the Major Components—Cellulose, Hemicellulose, and Lignin Ken-ichiro Tanoue 1,*, Kentaro Hikasa 1, Yuuki Hamaoka 1, Akihiro Yoshinaga 1, Tatsuo Nishimura 1, Yoshimitsu Uemura 2,3 and Akihiro Hideno 4 1 Department of Mechanical Engineering, School of Sciences and Engineering for Innovation, Yamaguchi University, Tokiwadai 2-16-1, Ube, Yamaguchi 755-8611, Japan; [email protected] (K.H.); [email protected] (Y.H.); [email protected] (A.Y.); [email protected] (T.N.) 2 NPO Kuramae Bioenergy, Minato-ku, Tokyo 108-0023, Japan; [email protected] 3 Center for Biofuel and Biochemical Research, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Malaysia 4 Paper industry innovation center of Ehime University, 127 Mendori-cho, Shkokuchuo 799-0113, Japan; [email protected] * Correspondence: [email protected]; Tel.: +81-836-85-9122 Received: 27 June 2020; Accepted: 6 August 2020; Published: 9 August 2020 Abstract: The torrefaction of three representative types of biomass—bamboo, and Douglas fir and its bark—was carried out in a cylindrical-shaped packed bed reactor under nitrogen flow at 573 K of the reactor wall temperature. As the thermal energy for the torrefaction was supplied from the top and the side of the bed, the propagation of the temperature profile of the bed is a crucial factor for discussing and improving the torrefaction reactor performance. Therefore, the temperature and gas flow rate (vector) profiles throughout the bed were calculated by model simulation so as to scrutinize this point.
    [Show full text]
  • Download PDF (Inglês)
    Brazilian Journal of Chemical ISSN 0104-6632 Printed in Brazil Engineering www.abeq.org.br/bjche Vol. 32, No. 01, pp. 23 - 33, January - March, 2015 dx.doi.org/10.1590/0104-6632.20150321s00003146 EVALUATION OF COMPOSITION, CHARACTERIZATION AND ENZYMATIC HYDROLYSIS OF PRETREATED SUGAR CANE BAGASSE A. A. Guilherme1*, P. V. F. Dantas1, E. S. Santos1, F. A. N. Fernandes2 and G. R. Macedo1 1Department of Chemical Engineering, Federal University of Rio Grande do Norte, UFRN, Av. Senador Salgado Filho 3.000, Campus Universitário, Lagoa Nova, Bloco 16, Unidade II, 59.078-970, Natal - RN, Brazil. Phone: + (55) 84 3215 3769, Fax: + (55) 84 3215 3770 E-mail: [email protected] 2Department of Chemical Engineering, Federal University of Ceará, UFC, Campus do Pici, Bloco 709, 60455-760, Fortaleza - CE, Brazil. (Submitted: December 2, 2013 ; Revised: March 28, 2014 ; Accepted: March 31, 2014) Abstract - Glucose production from sugarcane bagasse was investigated. Sugarcane bagasse was pretreated by four different methods: combined acid and alkaline, combined hydrothermal and alkaline, alkaline, and peroxide pretreatment. The raw material and the solid fraction of the pretreated bagasse were characterized according to the composition, SEM, X-ray and FTIR analysis. Glucose production after enzymatic hydrolysis of the pretreated bagasse was also evaluated. All these results were used to develop relationships between these parameters to understand better and improve this process. The results showed that the alkaline pretreatment, using sodium hydroxide, was able to reduce the amount of lignin in the sugarcane bagasse, leading to a better performance in glucose production after the pretreatment process and enzymatic hydrolysis.
    [Show full text]
  • Lignocellulosic Biomass Fractionation by Mineral Acids and Resulting
    Lignocellulosic biomass fractionation by mineral acids and resulting extract purification processes: Conditions, yields, and purities Vincent Oriez, Jérôme Peydecastaing, Pierre-Yves Pontalier To cite this version: Vincent Oriez, Jérôme Peydecastaing, Pierre-Yves Pontalier. Lignocellulosic biomass fractionation by mineral acids and resulting extract purification processes: Conditions, yields, and purities. Molecules, MDPI, 2019, 24 (23), 21 p. 10.3390/molecules24234273. hal-02622871 HAL Id: hal-02622871 https://hal.inrae.fr/hal-02622871 Submitted on 26 May 2020 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. Distributed under a Creative Commons Attribution| 4.0 International License molecules Review Lignocellulosic Biomass Fractionation by Mineral Acids and Resulting Extract Purification Processes: Conditions, Yields, and Purities Vincent Oriez * ,Jérôme Peydecastaing and Pierre-Yves Pontalier * Laboratoire de Chimie Agro-industrielle (LCA), Université de Toulouse, INRA, INPT, 4 allée Emile Monso, 31030 Toulouse, France; [email protected] * Correspondence: [email protected] or [email protected] (V.O.); [email protected] (P.-Y.P.) Academic Editor: Rafał Łukasik Received: 14 October 2019; Accepted: 14 November 2019; Published: 23 November 2019 Abstract: Fractionation of lignocellulose is a fundamental step in the valorization of cellulose, hemicelluloses, and lignin to produce various sustainable fuels and chemicals.
    [Show full text]
  • Lignocellulosic Biomass for Advanced Biofuels and Bioproducts: Workshop Report, DOE/SC-0170
    DRAFT: February 2015 Bioenergy Workshop June 23–24, 2014, Washington, D.C. Convened by U.S. Department of Energy Office of Science Office of Biological and Environmental Research Co-Chairs Erich Grotewold, Ph.D Kristala L. Jones Prather, Ph.D Ohio State University Massachusetts Institute of Technology Organizer Biological Systems Science Division Kent Peters, Ph.D. [email protected] 301.903.5549 http://genomicscience.energy.gov/biofuels/lignocellulose/ Mission The Office of Biological and Environmental Research (BER) advances world-class fundamental research programs and scientific user facilities to support the Department of Energy’s energy, environment, and basic research missions. Addressing diverse and critical global challenges, the BER program seeks to understand how genomic information is translated to functional capabilities, enabling more confident redesign of microbes and plants for sustainable biofuel production, improved carbon storage, or contaminant bioremediation. BER research advances understanding of the roles of Earth’s biogeochemical systems (the atmosphere, land, oceans, sea ice, and subsurface) in determining climate so that it can be predicted decades or centuries into the future, information needed to plan for energy and resource needs. Solutions to these challenges are driven by a foundation of scientific knowledge and inquiry in atmospheric chemistry and physics, ecology, biology, and biogeochemistry. Cover Credits Brown Column: From top to bottom. Poplar tree tops (Oak Ridge National Laboratory). Switchgrass (U.S. Department of Agriculture’s Agricultural Research Service). Atomic force micrograph showing nanometer-scale detail of interwoven rope-like, lignocellulosic microfibril bundles in a switchgrass cell wall (BioEnergy Science Center and National Renewable Energy Laboratory). Scanning electron micrograph of Clostridium cellulolyticum cells growing on switchgrass (BioEnergy Science Center and National Renewable Energy Laboratory).
    [Show full text]
  • Bioresources.Com
    PEER-REVIEWED ARTICLE bioresources.com PRODUCTION OF XYLO-OLIGOSACCHARIDES FROM MISCANTHUS x GIGANTEUS BY AUTOHYDROLYSIS Pablo Ligero,a Johannes C. van der Kolk,b Alberto de Vega,a,* and Jan E.G. van Dam b Xylo-oligosaccharides were obtained from Miscanthus x giganteus. The process was designed as a biorefinery scheme, which seeks the separation of the three main components: cellulose, hemicelluloses, and lignin. To extract the hemicelluloses, particularly xylans, in an efficient way, Miscanthus was subjected to autohydrolysis. The system was evaluated for the effects of temperature (160 to 200oC) and reaction time (15 to 60 min) on various parameters, reflecting the changes undergone during the process. The results showed that autohydrolysis is a suitable method for obtaining high yields of xylo-oligosaccharides, reaching values close to 65% of the dissolved xylans (based on the initial amount of potential xylose). Analysis of the process by using the severity factor (RO) allowed for the identification of a set of time-temperature values for which the fractionation was optimal. Keywords: Miscanthus x giganteus; Autohydrolysis; Xylo-oligosaccharides; Fractionation Contact information: a: Departament of Physical Chemistry and Chemical Engineering, Faculty of Sciences, University of A Coruña, Rúa da Fraga 10, 15004, A Coruña, Spain; b: Food and Biobased Research, Wageningen University and Research Centre, P.O. Box 17, 6700 AA Wageningen, The Netherlands; * Corresponding author: [email protected] INTRODUCTION Lignocellulosic biomass is considered to be a major source for ‘green’ chemicals, bio-fuels, and biobased products. Among the advantages of using lignocellulosic biomass can be mentioned that it is abundantly available around the world, non-competitive with food production, and it is a renewable and sustainable resource.
    [Show full text]
  • Food Or Non-Food: Which Agricultural Feedstocks Are Best for Industrial Uses?
    nova paper #2 on bio-based economy 2013-07 Food or non-food: Which agricultural feedstocks are best for industrial uses? Authors: Michael Carus (Dipl.-Physicist) and Lara Dammer (M.A. Pol. Sci.), nova-Institut GmbH nova papers on bio-based economy are proposals to stimulate the discussion on current WRSLFVRIWKHELREDVHGHFRQRP\E\FUHDWLQJQHZSHUFHSWLRQVEDVHGRQVFLHQWL¿FIDFWVDQG by inviting relevant stakeholders to participate in decision-making processes and debates. Contents Page 1 Executive Summary ............................................................................................... 2 2 Introduction & Objectives ...................................................................................... 2 3 Biomass use in the European Union and worldwide ............................................. 2 4 Current frameworks for the industrial use of biomass ...........................................4 5 A differentiated approach to finding the most suitable biomass for industry ........ 4 6 Facts about food and non-food crops ................................................................... 5 7 Level playing field for industrial material use and bioenergy/biofuels .................... 7 8 Impacts on policy – what are we asking for? ........................................................ 8 9 Literature ................................................................................................................ 9 Download this paper and further documents at: www.bio-based.eu/policy/en V.i.S.d.P.: Michael Carus, nova-Institut GmbH, Industriestrasse
    [Show full text]
  • Lignocellulosic Biomass: a Sustainable Platform for Production of Bio-Based Chemicals and Polymers
    Lignocellulosic Biomass: A Sustainable Platform for Production of Bio-Based Chemicals and Polymers Furkan H. Isikgora, C. Remzi Becer*b a Department of Chemistry, Boğaziçi University, Bebek, 34342 İstanbul, Turkey b School of Engineering and Materials Science, Queen Mary University of London, Mile End Road, E1 4NS London, United Kingdom The demand for petroleum dependent chemicals and materials has been increasing despite the dwindling of their fossil resources. As the dead-end of petroleum based industry has started to appear, today’s modern society has to implement alternative energy and valuable chemical resources immediately. Owing to the importance of lignocellulosic biomass for being the most abundant and bio-renewable biomass on earth, this critical review provides insights into the potential of lignocellulosic biomass as an alternative platform to fossil resources. In this context, over 200 value-added compounds, which can be derived from lignocellulosic biomass by using various treatment methods, are presented with their references. Lignocellulosic biomass based polymers and their commercial importance are also reported mainly in the frame of these compounds. The review article aims to draw the map of lignocellulosic biomass derived chemicals and their synthetic polymers, and to reveal the scope of this map in today’s modern chemical and polymer industry. cheaper than any other commodity products. However, the 1. Introduction. competitive price advantage of fossil fuels during the last century has disappeared.5 After crossing the oil production peak, the Modern industrial polymerization technologies make it possible dwindling of fossil resources will further boost the oil price and to produce versatile polymers with highly tunable properties and this situation will drastically impact the cost-effectiveness and broad range of applications.
    [Show full text]
  • Advances in Valorization of Lignocellulosic Biomass Towards Energy Generation
    catalysts Review Advances in Valorization of Lignocellulosic Biomass towards Energy Generation Ikram ul Haq 1, Kinza Qaisar 1, Ali Nawaz 1 , Fatima Akram 1 , Hamid Mukhtar 1,* , Xin Zohu 2, Yong Xu 2, Muhammad Waseem Mumtaz 3, Umer Rashid 4,* , Wan Azlina Wan Ab Karim Ghani 5,6,7 and Thomas Shean Yaw Choong 5 1 Institute of Industrial Biotechnology, Government College University, Lahore 54000, Pakistan; [email protected] (I.u.H.); [email protected] (K.Q.); [email protected] (A.N.); [email protected] (F.A.) 2 Jiangsu Co-Innovation Center of Efficient Processing and Utilization of Forest Resources, College of Chemical Engineering, Nanjing Forestry University, Nanjing 210037, China; [email protected] (X.Z.); [email protected] (Y.X.) 3 Department of Chemistry, Faculty of Science, University of Gujrat, Gujrat 50700, Pakistan; [email protected] 4 Institute of Advanced Technology, Universiti Putra Malaysia, Selangor 43400, Malaysia 5 Department of Chemical and Environmental Engineering, Faculty of Engineering, Universiti Putra Malaysia, Selangor 43400, Malaysia; [email protected] (W.A.W.A.K.G.); [email protected] (T.S.Y.C.) 6 Sustainable Process Engineering Research Center (SPERC), Faculty of Engineering, Universiti Putra Malaysia, Selangor 43400, Malaysia 7 Institute of Plantations Studies, Universiti Putra Malaysia, UPM Serdang, Selangor 43400, Malaysia Citation: Haq, I.u.; Qaisar, K.; * Correspondence: [email protected] or [email protected] (H.M.); Nawaz, A.; Akram, F.; Mukhtar, H.; [email protected] or [email protected] (U.R.); Tel.: +92-333-4245581 (H.M.); Zohu, X.; Xu, Y.; Mumtaz, M.W.; +60-397-697393 (U.R.) Rashid, U.; Ghani, W.A.W.A.K.; et al.
    [Show full text]
  • Lignocellulosic Biomass
    Challenges of Ethanol Production from Lignocellulosic Biomass Maha Dakar Varieties of Carbohydrates Sugar Starchh Cellulose/Hemicellulose What All Plants Have in Common Cellulose Glucose Why is it difficult to hydrolyze lignocellulosic biomass i nt o sugar tkthl?to make ethanol? Lignocellulosic Biomass • Biomass: biological material derived from living organisms. Biomass for energy related to plant • Lignocellulosic biomass: cellulose, hemicellulose (complex carbohydrates) & lignin • Cellulose: structural material in plants & most abundant biomass in earth • Lignocellulose: strength, resistance to degradation • Cellulose & hemicellulose: ppyolymers of suggpars, potential source of fermentable sugars • Lignocellulosic biomass do not directly go into food Lignocellulosic Biomass Feedstock • Woody Biomass - FtidForest residues - Wood waste • Non-Woody Biomass - Agricultural Residues: ¾Straws (w hea t, barl ey, ri ce) ¾Bagasse (sugarcane, sweet sorghum) ¾Stover (corn, milo) • Organic Waste - Animal waste - Sewage sludge What is Lignocellulosic Material? lignocellulose = lignin + cellulose + hemicellulose Cellulose Hemicellulose Lignin Composition of Lignocellulose 1st Generation vs. 2nd Generation 2nd 1st 2nd 1st How Do We Go From This To This? Switchgrass Bagasse Plants Cell Walls Plants Cell Walls: - Middle lamella: pectin - Primary cell wall: cellulose, hemicellulose - Secondary cell wall: lignin Middle lamella Primary cell wall Secondary cell lwalll wall Plasma membrane Op timi zi ng pl ant bi omass f or effi ci enttiidtdi processing requires
    [Show full text]
  • Miscanthus: a Fastgrowing Crop for Biofuels and Chemicals Production
    Review Miscanthus: a fast- growing crop for biofuels and chemicals production Nicolas Brosse, Université de Lorraine, Vandoeuvre-lès-Nancy, France Anthony Dufour, CNRS, Université de Lorraine, Nancy, France Xianzhi Meng, Qining Sun, and Arthur Ragauskas, Georgia Institute of Technology, Atlanta, GA, USA Received February 9, 2012; revised April 17, 2012; accepted April 18, 2012 View online at Wiley Online Library (wileyonlinelibrary.com); DOI: 10.1002/bbb.1353; Biofuels, Bioprod. Bioref. (2012) Abstract: Miscanthus represents a key cand idate energy crop for use in biomass-to-liquid fuel-conversion processes and biorefi neries to produce a range of liquid fuels and chemicals; it has recently attracted considerable attention. Its yield, elemental composition, carbohydrate and lignin content and composition are of high importance to be reviewed for future biofuel production and development. Starting from Miscanthus, various pre-treatment technolo- gies have recently been developed in the literature to break down the lignin structure, disrupt the crystalline structure of cellulose, and enhance its enzyme digestibility. These technologies included chemical, physicochemical, and biological pre-treatments. Due to its signifi cantly lower concentrations of moisture and ash, Miscanthus also repre- sents a key candidate crop for use in biomass-to-liquid conversion processes to produce a range of liquid fuels and chemicals by thermochemical conversion. The goal of this paper is to review the current status of the technology for biofuel production from
    [Show full text]
  • Toward Complete Utilization of Miscanthus in a Hot-Water Extraction-Based Biorefinery
    energies Article Toward Complete Utilization of Miscanthus in a Hot-Water Extraction-Based Biorefinery Kuo-Ting Wang ID , Chengyan Jing, Christopher Wood, Aditi Nagardeolekar ID , Neil Kohan, Prajakta Dongre, Thomas E. Amidon and Biljana M. Bujanovic * Department of Paper and Bioprocess Engineering, SUNY College of Environmental Science and Forestry, 1 Forestry Drive, Syracuse, NY 13210, USA; [email protected] (K.-T.W.); [email protected] (C.J.); [email protected] (C.W.); [email protected] (A.N.); [email protected] (N.K.); [email protected] (P.D.); [email protected] (T.E.A.) * Correspondence: [email protected]; Tel.: +1-315-470-6907 Received: 31 October 2017; Accepted: 21 December 2017; Published: 25 December 2017 Abstract: Miscanthus (Miscanthus sp. Family: Poaceae) was hot-water extracted (two h, at 160 ◦C) at three scales: laboratory (Parr reactor, 300 cm3), intermediate (M/K digester, 4000 cm3), and pilot (65 ft3-digester, 1.841 × 106 cm3). Hot-water extracted miscanthus, hydrolyzate, and lignin recovered from hydrolyzate were characterized and evaluated for potential uses aiming at complete utilization of miscanthus. Effects of scale-up on digester yield, removal of hemicelluloses, deashing, delignification degree, lignin recovery and purity, and cellulose retention were studied. The scale-dependent results demonstrated that before implementation, hot-water extraction (HWE) should be evaluated on a scale larger than a laboratory scale. The production of energy-enriched fuel pellets from hot-water extracted miscanthus, especially in combination with recovered lignin is recommended, as energy of combustion increased gradually from native to hot-water extracted miscanthus to recovered lignin. The native and pilot-scale hot-water extracted miscanthus samples were also subjected to enzymatic hydrolysis using a cellulase-hemicellulase cocktail, to produce fermentable sugars.
    [Show full text]