DOCSLIB.ORG

3-In-1 Saw Major Qualifying Project AY 2012, 2013

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
3-In-1 Saw Major Qualifying Project AY 2012, 2013 WORCESTER POLYTECHNIC INSTITUTE 3-in-1 Saw Major Qualifying Project AY 2012, 2013 Edward Galvin Mathew Fredrick Timothy Moreau Design and prototyping of a carpenter’s saw to perform the functions of three different saws; slide-compound miter saw, table saw, and handheld circular saw. Table of Contents Background Information ................................................................................................................. 5 Glossary of Terms ........................................................................................................................... 5 Types of Saws ................................................................................................................................. 6 Circular Saw ............................................................................................................................ 6 Chop Saw ................................................................................................................................. 7 Table Saw ................................................................................................................................ 7 Background Research ..................................................................................................................... 8 Overview ......................................................................................................................................... 8 Flip-Over Saws ............................................................................................................................... 8 Category II Saws ............................................................................................................................. 9 Conclusions ................................................................................................................................... 10 Design Process .............................................................................................................................. 10 General Schematic Design ............................................................................................................ 11 Introduction ........................................................................................................................... 12 Circular Saw Attachment Design Progression ...................................................................... 12 Aligning the Circular Saw ..................................................................................................... 12 Locking Devices .................................................................................................................... 13 Converting the Miter Saw to a Table Saw .................................................................................... 14 General Conversion Concept ................................................................................................. 15 Locking Mechanisms ............................................................................................................. 15 Controlling Table Motion ...................................................................................................... 16 Raising and Lowering the Table Saw Blade ......................................................................... 16 Design Details ............................................................................................................................... 17 Circular Saw Details .............................................................................................................. 17 Miter Saw Details .................................................................................................................. 17 Table Saw Details .................................................................................................................. 23 Design of Blade Raising and Lowering Device .................................................................... 25 Prototyping .................................................................................................................................... 26 Evaluation ..................................................................................................................................... 29 Recommendations ......................................................................................................................... 29 3-in-1 Combination Saw MQP Page 1 Safety Features .............................................................................................................................. 29 Design Built-In Table Safety Specifications................................................................................. 31 Optimize for Weight and Material Selection ................................................................................ 31 Design for Manufacturability and Tolerances .............................................................................. 32 Works Cited .................................................................................................................................. 33 Appendix A: MathCad Calculations ............................................................................................. 35 Appendix B: Weekly Meeting Notes ............................................................................................ 37 Appendix C: Poster Presentation .................................................................................................. 45 3-in-1 Combination Saw MQP Page 2 Table of Figures Figure 1: Circular Saw (Circular Saw) ........................................................................................... 6 Figure 2: Miter Saw (Dewalt Miter Saw) ....................................................................................... 7 Figure 3: Table Saw (Craftsman) .................................................................................................... 7 Figure 4: DeWalt DW743 Flip-Over Saw – Left (DW743N-QS) .................................................. 8 Figure 5: Bosch GTM 12 Professional Category II Saw – Right (Bosch Table Saw).................... 8 Figure 6: Patent US 20100269660 A1 Category II Saw – Left (Patent US20100269660) ............ 9 Figure 7: Patent US 7891277 B2 Category II Saw – Right (Patent US7891277) .......................... 9 Figure 8: Makita LF1000 Flip-Over Saw – Left (Makita) .............................................................. 9 Figure 9: Patent US 20070234864 Flip-Over Saw – Right (Patent US20070234864)................... 9 Figure 10: Device in Circular Saw Mode ..................................................................................... 11 Figure 11: Device in Miter Saw Mode ......................................................................................... 11 Figure 12: Device in Table Saw Mode ......................................................................................... 11 Figure 13: Alignment Pins for Circular Saw ................................................................................ 12 Figure 14: Latching Mechanism for Circular Saw ....................................................................... 13 Figure 15: Table Flipped to Chop Saw Mode – left ..................................................................... 15 Figure 16: Table Flipped to Table Saw Mode – right ................................................................... 15 Figure 17: Ball Detent Ratchet Wrench Mechanism (FIELD OF THE INVENTION) ............... 15 Figure 18: Gas Shock (PPL Motor Homes) .................................................................................. 16 Figure 19: Raising and Lowering Table Saw Blade Mechanism ................................................. 16 Figure 20: Length of Cut Diagram................................................................................................ 18 Figure 21: Travel Length Diagram ............................................................................................... 19 Figure 22: Bevel Adjustment of Chop Saw (Amazon.com) ......................................................... 20 Figure 23: Successive Slides Illustration – Fully Extended (Left) ............................................... 21 Figure 24: Successive Slides Illustration – Fully Collapsed (Right) ............................................ 21 Figure 25: Solid Aluminum Turntable (Left) ............................................................................... 22 Figure 26: Steel Reinforced Turntable (Right) ............................................................................. 22 Figure 27: Radial Arm Free Body Diagram ................................................................................. 22 Figure 28: Table Saw Cut Depth and Deflection vs. Thickness ................................................... 23 Figure 29: Mechanism to Raise and Lower Blade ........................................................................ 24 Figure 30: Linkage Development Sketch ..................................................................................... 25 Figure 31: CAD Model in Miter Saw Mode – Top Left ............................................................... 27 Figure 32: CAD Model in Table Saw Mode – Top Right ............................................................ 27 Figure 33: Beveled and Mitered Prototype – Bottom Left ........................................................... 27 Figure 34: First Prototype in Miter Saw Mode – Bottom Right ..................................................
Load more

Recommended publications
  • Tim's Taper Tool
    Tim’s Taper Tool For Nocks and Tips Installation and Operating Instructions for use on Table Saws and Large Sanders CAUTION ! DO NOT USE YOUR TAPER TOOL WITH A SAW BLADE. USE ONLY WITH A SANDING DISC!! BE FAM ILIAR WITH YOUR S AW OR DISC SA NDER O PERA TIONS A ND FOLLO W ALL SAFETY PRECAUTIONS. Read all directions before you start. Please follow these directions carefully and do not hurry through the process. 1. Place the guide inside the slot on your table saw or disc sander. If the guide is too large, slowly sand or cut down the short side of the guide until it fits into the slot. 2. Once the guide fits into the slot, push it to the bottom of the slot. Place a good grade of wood glue on one of the wedges and push into place. Glue and place the second wedge. Now apply firm pressure to the en ds of both wedges to force them against the guide . Allow to dry. 3. After the glue has dried, attach the taper tool to the guide with the thumb screws. Finger tighten. 4. Remove the assembled tool from the slot and set aside. You are almost ready to begin tapering your arrow shafts, BUT .... 5. Inspect your sanding wheel carefully! If the sand paper is loose or damaged REPLACE it! The taper tool fits closely to the wheel and loose sand paper will damage the tool and ruin your arrow shafts. 80 grit sand paper is recommended for tapering your arrow shafts but any grit from 60 to 120 will work.
    [Show full text]
  • Manufacturing Capabilities
    Manufacturing ES2 Capabilities Introduction CACI has built up a robust manufacturing capacity with unique capabilities ranging from low-rate precision prototyping to rapid prototyping and small batch manufacturing at several of the company’s sites. We provide specialized and unique manufacturing support to both our U.S. Government and commercial customers at these locations. Our Albuquerque, New Mexico site can produce precision-machined parts using aluminum and steel, and is equipped with a host of cutting- edge metalworks machinery, as well as an intensive welding capability. CACI’s Lexington Park, Maryland site also has dedicated staff available to support small batch manufacturing and rapid prototyping with ferrous and non-ferrous metals. Our Columbia, Maryland site specializes in high-precision design and high-complexity prototype fabrication using a variety of materials and machining techniques. All of our sites and facilities operate CACI-owned machinery and can support any customer’s manufacturing requirements. Table of Contents Logistics Support Facility ▪ Albuquerque, New Mexico ................................................2 What We Do .........................................................................................................................................................3 Our Manufacturing and Fabrication Capabilities ..................................................................................... 4 Integrated Products and Services ▪ Lexington Park, Maryland ................................6 What We Do
    [Show full text]
  • Cast Iron Router Wing Instructions Step 1 Step 2 Shop Note
    Cast Iron Instructions Part # 1066.3040 Router Wing Version 2.0 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Fulton™ Woodworking Tools & Accessories and its subsidiaries assume no liability for accidents or injuries caused by improper use of this product. Fulton™ Woodworking Tools & Accessories P.O. Box 921487 Norcross GA 30010 www.fultonwoodworkingtools.com © Copyright Fulton™ Woodworking Tools & Accessories 02/2012. All images, copy, and graphics are copyrighted by law and may not be copied, or reproduced without our express written consent. What’s In The Box? Parts List 1 each Cast Iron Router Table (Wing) 1 each Phenolic Insert Router Mounting Plate 2 each 1/4 x 20 Star Knobs with 1-1/2” x 20 bolts 1 each 1/8” Hex Wrench 1 each Assembly Instruction and Safety Booklet 3 each 3/8” Washers 3 each M10 x 1.5 x 40mm Hex Bolts 3 each 7/16” x 20 x 1-1/2” Hex Bolts 4 each 5/16” x 18 x 1-1/2” Hex Bolts 4 each 5/16” x 18 Hex Nuts 4 each 5/16” Lock Washers 8 each 5/16” Flat Washers 10 each 1/4” x 20 x 1-1/4” Nylon Thumbs Screws 10 each 1/4” x 20 Hex Nuts Thank you for purchasing the Cast Iron Router Wing. The Cast Iron Router Wing can be mounted to your table saw, cabinet, or open steel stand. Or, bolt two router tables together - back to back. You must fabricate your own stand or cabinet.
    [Show full text]
  • Power Tool Guide 05J50.01
    Power Tool Guide 05J50.01 The Veritas® Power Tool Guide is a collapsible straightedge that can be clamped to any material under 1" thick. The 52" tool guide (05J50.03) can be clamped across sheet material up to 52". The 8' Power Tool Guide (05J50.01), or the 48" tool guide extension (05J50.04) added to the 52" tool guide, can be clamped across sheet material up to 100". The advantage this guide has over other 8' guides is that it may be dismantled quickly and easily for cutting smaller sheet material as well as for easier storage or transport. The guide includes a pair of 1" capacity clamps that can be positioned anywhere along its length. For clamping material thicker than plywood sheets, a pair of 2" capacity clamps (05J50.09) is available separately. An optional 12" traveller (05J50.02) used in conjunction with a user-made base plate ensures that your power tool will effortlessly follow the intended line with greater safety. The utility of the traveller is further enhanced with the optional position stop (05J50.10) that clamps onto either guide rail. Figure 1: Veritas® Power Tool Guide. Safety Rules These safety instructions are meant to complement those that came with your power tool. We suggest that you reread those, in addition to these listed here before you begin to use this product. To use this product safely, always follow both sets of safety and general instructions. 1. Read the manual. Learn the tool’s applications and limitations as well as the specific hazards related to the tool.
    [Show full text]
  • 35530 Table Saws TG
    Woodworking Tools Table Saws Teacher’s Guide Introduction This Teacher’s Guide provides information to help you get the most out of Table Saws, part of the Woodworking Tools series. The contents in this guide will allow you to prepare your students before they use the program, assist them as they navigate through the content, and present follow- up activities to reinforce the material’s key learning points. Woodworking Tools is a 16-part series of programs that address the safe operation of the most popular and useful types of woodworking tools. Each program delves into a different tool, including its purpose and associated parts. It teaches students how to choose the proper blade or bit for the task and perform the various woodworking operations that can be accomplished with a particular tool. The 16 videos in this series enable and encourage students to safely and creatively use power tools to their maximum proficiency. Table Saws is a 22-minute video targeted to teenagers and young adults. Its content is appropri- ate to such curriculum areas as Technology Education, Trade, and Industrial Education. In addition, the information presented in Woodworking Tools could also be presented in vocational/technical schools or adult education courses that focus on shop, carpentry, woodworking, or construction education and research. Learning Objectives After watching each video program in the series, students will be able to: • Identify which tools are best for which job in the wood shop. • Understand how to safely operate a variety of woodworking tools. • Demonstrate how to safely clean, maintain, and sharpen a variety of woodworking tools.
    [Show full text]
  • Circular Saw Safety
    CIRCULAR SAW SAFETY Tool Box Talk Hand-held circular saws are powerful tools that can spin their blades at over 5,000 revolutions per minute. It’s important to choose safety and always use saws properly and with care. Hazards to be aware of include noise, flying debris, electrical, and saw kickback. Saws should be inspected before use and only used by qualified personnel. Safe setup prior to cutting: Safety while cutting: • Always wear ANSI Z87.1+ safety glasses, • Avoid cutting into blind areas goggles, or face shield with eye protection • Avoid twisting the saw to change, cut, or check alignment • Hearing protection is recommended; saws are loud • Saw should not need to be forced during cutting and longtime exposure may lead to hearing loss • Check for obstructions or objects like nails and screws • Wear proper respiratory protection when required • Do not carry the saw with a finger on the trigger switch • Avoid wearing loose clothing or jewelry • Stand to the side when cutting to keep out of the line that may be pulled into the saw of cut if kickbacks occur, do not overextend — position • While unplugged, check retracting lower your feet so you’re balanced and in full control blade guard to ensure it works freely • Be alert to the possibility of the blade binding • Tighten blade-locking nut to manufacturer specifications and the potential for and kickback • While unplugged, set and lock blade depth so lowest tooth • Always use both hands on the handles for does not extend more than 0.3 cm (⅛") beneath the wood maximum control, and
    [Show full text]
  • Manufacturing Glossary
    MANUFACTURING GLOSSARY Aging – A change in the properties of certain metals and alloys that occurs at ambient or moderately elevated temperatures after a hot-working operation or a heat-treatment (quench aging in ferrous alloys, natural or artificial aging in ferrous and nonferrous alloys) or after a cold-working operation (strain aging). The change in properties is often, but not always, due to a phase change (precipitation), but never involves a change in chemical composition of the metal or alloy. Abrasive – Garnet, emery, carborundum, aluminum oxide, silicon carbide, diamond, cubic boron nitride, or other material in various grit sizes used for grinding, lapping, polishing, honing, pressure blasting, and other operations. Each abrasive particle acts like a tiny, single-point tool that cuts a small chip; with hundreds of thousands of points doing so, high metal-removal rates are possible while providing a good finish. Abrasive Band – Diamond- or other abrasive-coated endless band fitted to a special band machine for machining hard-to-cut materials. Abrasive Belt – Abrasive-coated belt used for production finishing, deburring, and similar functions.See coated abrasive. Abrasive Cutoff Disc – Blade-like disc with abrasive particles that parts stock in a slicing motion. Abrasive Cutoff Machine, Saw – Machine that uses blade-like discs impregnated with abrasive particles to cut/part stock. See saw, sawing machine. Abrasive Flow Machining – Finishing operation for holes, inaccessible areas, or restricted passages. Done by clamping the part in a fixture, then extruding semisolid abrasive media through the passage. Often, multiple parts are loaded into a single fixture and finished simultaneously. Abrasive Machining – Various grinding, honing, lapping, and polishing operations that utilize abrasive particles to impart new shapes, improve finishes, and part stock by removing metal or other material.See grinding.
    [Show full text]
  • The Original. Versatile and Powerful
    iNTEriOr CONSTruCTiON The Original. Versatile and powerful. FEiN MultiMastEr – the universal system for interior construction and renovation NEW! Now available in a cordless version From the inventor of the power tool: FEIN MultiMaster. More than 40 year’s experience is built into this system. Original FEiN accessories – developed for the MultiMastEr. FEIN brought the first oscillating power tool to the market Original FEIN accessories guarantee outstanding results and an over 40 years ago. These decades of experience are built into unrivalled long service life. It handles all common renovation and the FEIN MultiMaster, making this universal system for interior interior construction work for professionals and also provides construction and renovation unique in its diversity of applications unique application solutions. Maximum performance, safety and and performance. In addition, the MultiMaster impresses with high reliability are guaranteed with the FEIN MultiMaster. quality components and is an indispensible companion for trade and industrial professionals. Technology / Quality The Original Page 4 The MultiMaster Page 6 The MultiMaster Cordless Page 7 Accessories know-how Page 10 2 FEiN MultiMastEr Cordless – mobile and powerful. Your benefits with FEiN oscillating power tools: The new battery version makes the FEIN MultiMaster more flexible and convenient than ever. Cordless, but with identical performance, ɰ More than 40 year’s experience with oscillation technology. so work can be done anywhere, even without a power supply. And ɰ The high “Made in Germany” quality you expect. all this in the durable quality that you expect from a real Original. ɰ Unrivalled performance and versatility. ɰ Original FEIN accessories for perfect results and maximum tool life.
    [Show full text]
  • Router Table
    Router Table Read This Important Safety Notice To prevent accidents, keep safety in mind while you work. Use the safety guards installed on power equipment; they are for your protection. When working on power equipment, keep fingers away from saw blades, wear safety goggles to prevent injuries from flying wood chips and sawdust, wear hearing protection and consider installing a dust vacuum to reduce the amount of air- borne sawdust in your woodshop. Don’t wear loose clothing, such as neckties or shirts with loose sleeves, or jewelry, such as rings, necklaces or bracelets, when working on power equipment. Tie back long hair to prevent it from getting caught in your equipment. People who are sensitive to certain chemicals should check the chemical con- tent of any product before using it. Due to the variability of local conditions, construction materials, skill levels, etc., neither the author nor Popular Woodworking Books assumes any responsibility for any accidents, injuries, damages or other losses incurred resulting from the mate- rial presented in this book. The authors and editors who compiled this book have tried to make the con- tents as accurate and correct as possible. Plans, illustrations, photographs and text have been carefully checked. All instructions, plans and projects should be carefully read, studied and understood before beginning construction. Prices listed for supplies and equipment were current at the time of publica- tion and are subject to change. Metric Conversion Chart to convert to multiply by Inches. Centimeters. 2.54 Centimeters. Inches . 0.4 Feet. Centimeters. 30.5 Centimeters. Feet. 0.03 Yards.
    [Show full text]
  • Safe Hand Tool and Portable Power Tool Use and Inspections
    Safe Tool Use • Wear appropriate Personal Protective Equipment. – All volunteers should have hard hats and safety glasses on at all times while on site. – In addition: • Provide dust masks (sanding, sweeping, insulating, etc.) • Provide ear plugs (power tools, work in enclosed spaces) • Provide knee pads, gloves, and any other safety equipment to increase comfort of crew members. Safe Tool Use • Do not allow the operation of tools without approval and supervision. – Make sure all members of your crews are trained to use the tools they need. – Remember: Everyone must get an orientation to all power saws before they use them, regardless of their personal experience. • Allow volunteers time to learn and encourage them to practice. – Make sure they are comfortable using tools after instruction. Safe Tool Use • Do not over-exert yourself or the tool. – This can lead to slips and strains. Encourage volunteers to take breaks rather than overexerting or straining themselves. • Place yourself in a good body position. – Most hand tool accidents result from being struck by the tool or flying chips. • Use only sharp knives, blades and bits. – Replace as necessary. Make sure volunteers are comfortable replacing bits and blades or coming to you when they need one replaced. Inspecting Hand Tools • Regularly inspect tools for broken or missing pieces. – Inspect screws, nuts, bolts and moveable parts to make sure they are tightened. – Check handles for cracks and splinters. – Never use tape to fix a handle; it is a direct OSHA violation. X • Do not use damaged tools. – Take the tool out of use , clearly label it and send it to the warehouse for repairs.
    [Show full text]
  • Unjointablestock 6.33 3.Indd
    Joint the Unjointables 4 simple ways to work around your jointer By Jim Harrold B efore starting any project, techniques to rehabilitate these This jig consists of a base and you first have to prepare your “unjointables” and turn shop a bridge. To make the base you stock. You know the drill: flatten Face-jointclutter into shop big projects. boards can screw into, simply clamp a face, plane to thickness, joint an with a router a piece of ¾" MDF or plywood edge, rip to width, joint the sawn to your benchtop. Place the edge, and, finally, cut to length. workpiece on the base and Since the first face and edge While face-jointing boards of serve as reference for every other average size poses no problem if step, getting them right matters. you own a jointer and a planer, Bowl bit Typically, flattening and extra wide stock does. Sometimes straightening is done at the you can’t bear to rip the wide jointer, but special cases come stock, such as a treasured piece along. How, for instance, do you of crotch walnut, into narrower safely and successfully joint a widths to fit a 6" jointer. And you board that measures a meager surely don’t want to saw up a big The fl at bott om and radiused 12" in length, or one that’s too slab set aside for a rustic bench. edges of this 11/4"-diameter bowl wide for your planer, or a piece For oversized stock, turn bit (Woodcraft #24B86) make it of wild-grained wood that to your router, a dishing an effi cient wide-board surfacer.
    [Show full text]
  • The Circular Saw Blades Used in the Current Work Were Manufactured from Solid M2 HSS
    INVESTIGATION OF THE WEAR AND FAILURE MODES OF SURFACE ENGINEERED MULTIPOINT CUTTING TOOLS. A thesis submitted for the fulfilment of the requirements for the degree of Master of Engineering at Dublin City University. Martin G. Fleming B Sc. Department of Mechanical and Manufacturing Engineering. August 1992 Supervisor: Prof. M S J. Hashmi " It is a good thing to have two ways of looking at a subject, and to admit that there are two ways of looking at it. " JAMES CLERK MAXWELL (1831-1879) TO MY FAMILY DECLARATION I hereby declare that all the work prepared in this thesis was carried out by me at EOLAS (The Irish Science & Technology Agency) during the period February 1990 to August 1992 To the best of my knowledge, the results presented in this thesis orginated from the present study except where references have been made No part of this thesis has been submitted for a degree at any other institution Signature of Candidate ¿ fa * ' Martin G Fleming ACKNOWLEDGEMENTS This current work, was only made possible through the kind assistance of a number of my colleagues in the Materials Technology and Ceramics Research Departments in EOLAS whose assistance and goodwill I have much appreciated. Firstly thanks are due to Dr. Tony Carroll, Head of the Materials Technology Department, EOLAS for allowing me to pursue this research through the Departments EC-BRITE Cutting Tool Research Project. I am indebted to Mr. Bill Hogan for his technical assistance and the many constructive discussions throughout my work in EOLAS. Further thanks are due to my colleagues namely Tony Horan, Richard Murphy, Colin Pope, Dr.
    [Show full text]