Write the Name of the Following Tools
Total Page:16
File Type:pdf, Size:1020Kb
Load more
Recommended publications
-
Heavy Equipment Technology Required Tool List
Heavy Equipment Technology Required Tool List WRENCHES 1 1/2” Drive socket set: - Sockets, 3/8” to 1-1/14”, 6 point, shallow well - Sockets, 7/16” to 1-1/8”, 6 point, deep well - Sockets, 7/16” to 15/16”, Impact, 6 point, shallow well - Sockets, 7/16” to 15/16”, Impact, 6 point, deep well - Sockets, 10mm to 32 mm, 6 point, shallow well - Sockets, 10mm to 19mm, 6 point, deep well - Sockets, 10mm to 25mm’ Impact, 6 point, deep well - Ratchet - Breaker Bar - Drive Extensions: 1-1/2”, 3”, 5”, 10”, and 15” - Drive Adapter: 1/2” to 3/8” - 250 lb. Torque Wrench, Micrometer adjust - Impact Wrench, 3/4 or 1/2, Pneumatic or Battery - Universal Joint 1 3/8” Drive socket set: - Sockets, 1/4" to 15/16”, 6 point, shallow well - Sockets, 6mm to 19mm, 6 point shallow well - Universal Sockets, 3/8” to 3/4", 6 point shallow well - Sockets, T30 to T55, Drivers - Spark plug Sockets, 5/8” and 13/16” - Ratchet - Breaker bar - Drive extensions: 1-1/2”, 3”, 6”,10” - Universal Joint 1 1/4” Drive socket set: - Sockets, 3/16” to 9/16”, 6 point, shallow well - Sockets, 3/16” to 9/16”, 6 point, deep well - Sockets, 5.5mm to 14mm, 6 point, shallow well - Sockets, 5.5mm to 14mm, 6 point, deep well - Sockets, T8 to T27, Drivers - Ratchet - Drive extensions: 2”, 4”, 6” - Universal Joint 1 Combination End set: - 1/4" to 1-1/4”, Long - 6mm to 24mm, Long 1 Flare Nut set: - 1/4" to 13/16” - 9mm to 21mm 1 Ratcheting Box End: - 1/4” x 3/8” and 3/16” x 5/16”, Square, Air Conditioning 1 8” Adjustable Wrench 1 14” Pipe Wrench 1 Hex Key set: - 5/64” to 3/8”, Long Arm -1.5mm to -
Water Hammer Arrestors Materials Water Hammer Arrestor Should Be Selected
Sizing and Placement Rule 1 covers multiple fixture branch lines which do not exceed 20 feet length. Series 15M2 Explanation - Fixture unit sizing and selection table is used to Water Hammer Arrestor select the required PDI unit (water hammer arrestor). For Commercial/Residential Systems Riser Up to 20' Rule 1 Typical Branch Line Rule 2 covers multiple fixture branch lines which exceed 20 feet As shown above, it has been established that the preferred location in length. for the water hammer arrestor is at the end of the branch line between Explanation - Fixture unit sizing and selection table is used to the last two fixtures served. select the required PDI unit (water hammer arrestor). The sum of The location of the water hammer arrestor shown above applies to the fixture unit rating of units X and Y shall be equal to or greater branch lines that do not exceed 20 feet in length, from the start of the than the demand of the branches. horizontal branch line to the last fixture supply on this branch line. When the branch line exceeds the 20 foot length, an additional water Over 20' hammer arrestor should be used. This practice is best defined by two Rule 2 Features rules which have been established to cover the placement of water • NPT solid hex brass adapter or solder end connection hammer arrestors. for easy installation 15M2 • Approved for installation with no access panel required 15M2S • May be installed in new or existing plumbing systems with a standard pipe tee vertically, horizontally or at any angle • PDI Listed (PDI WH201) • Maintenance free – unit piston is the only moving part Selection for Long Piping Runs Sizing Table • Air pre-load is 60 psi (4.2 bar) Pre-charged The majority of sizing and selection applications will involve single and For Water Pressures up to 65psi Air Chamber multiple fixture branch lines. -
Paul Sellers' Workbench Measurements and Cutting
PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST NOTE When putting together the cutting list for my workbench, I worked in imperial, the system with which I am most comfortable. I was not happy, however, to then provide direct conversions to metric because to be accurate and ensure an exact fit this would involve providing measurements in fractions of millimetres. When I do work in metric I find it more comfortable to work with rounded numbers, therefore I have created two slightly different sets of measurements. This means that in places the imperial measurement given is not a direct conversion of the metric measurement given. Therefore, I suggest you choose one or other of the systems and follow it throughout. © 2017 – Paul Sellers v2 PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST WOOD QTY DESCRIPTION SIZE (IMPERIAL) SIZE (METRIC) (THICK X WIDE X LONG) (THICK X WIDE X LONG) 4 Leg 2 ¾” x 3 ¾” x 34 ⅜” 70 x 95 x 875mm 1 Benchtop 2 ⅜” x 12” x 66” 65 x 300 x 1680mm 2 Apron 1 ⅝” x 11 ½” x 66” 40 x 290 x 1680mm 1 Wellboard 1” x 12 ½” x 66” 25 x 320 x 1680mm 4 Rail 1 ½” x 6” x 26” 40 x 150 x 654mm 2 Bearer 1 ¼” x 3 ¾” x 25” 30 x 95 x 630mm 4 Wedge ⅝” x 1 ½” x 9” 16 x 40 x 228mm 4 Wedge retainer ⅝” x 1 ½” x 4” 16 x 40 x 100mm HARDWARE QTY DESCRIPTION SIZE (IMPERIAL) SIZE (METRIC) 1 Vise 9” 225mm Dome head bolts (including nuts and washers) for 4 ⅜” x 5” 10 x 130mm bolting legs to aprons 2 Lag screws (with washers) for underside of vise ½” x 2 ½” 12 x 65mm 2 Lag screws for face -
EYELET PLIERS Instruction Guide for Eyelets
574 EYELET PLIERS Instruction Guide for Eyelets Instrucciones españolas ©2015 Prym Consumer USA Inc. 950 Brisack Rd. • Spartanburg, SC 29303 www.dritz.com 574 EYELET PLIERS – Instructions Fabric Preparation for Use two layers of light to medium-weight fabric, reinforced with interfacing. " and ¼" Eyelets Mark position of eyelets. ⁵∕₃₂ Test an eyelet on swatch of fabric. Instructions for Cutting ⁵∕₃₂" Holes in Fabric Pliers Tools: Inserting Tools: Insert die base (large hole opening Metal Die Metal Cone facing out) in one side of pliers Base Punch and cone punch in other side. Cutting Holes: Removing Tools: 1. Position fabric in pliers and 2. After cutting several holes, it may be 3. If pliers’ tools will not cut Slip hook of gray tool remover center tools over mark. necessary to clear hole cutouts from through your specic type of inside ledge of pliers and press Squeeze pliers rmly to die base. Use a strong straight pin to fabric, trace inside of eyelet down to release tool. cut hole. remove fabric cutouts from die. and cut hole with scissors. Repeat for opposite side. 1. 2. 3. Instructions for Cutting ¼" Holes in Fabric Pliers Tools: Inserting Tools: Insert round die base in one Metal Round Metal Cone side of pliers and cone punch Die Base Punch in other side. Cutting Holes: Removing Tools: 1. Position fabric in pliers and 2. After cutting several holes, it may be 3. If pliers’ tools will not cut Slip hook of gray tool remover center tools over mark. necessary to clear hole cutouts from through your specic type of inside ledge of pliers and press Squeeze pliers rmly to die base. -
Reducing the Risk of Injury
CHAPTER 5 Reducing the Risk of Injury CONTENTS 1 Standards for Ergonomic Tools 2 Tools and the Upper Extremities 3 Preventing Back Injuries 4 Workplace Conditions 72 INTRODUCTION Changing the way work is done can be difficult. It is also hard for most people to believe that what is done today may be causing unseen damage OBJECTIVES that won’t show up for months, years, or longer. The first step is to under- Upon successful completion stand why change must happen. Other chapters in Ergonomics discuss the of this chapter, the role risk factors play in developing cumulative trauma disorders (CTDs) participant should be work-related musculoskeletal disorders WMSDs and ( ). The best way to able to: prevent workplace injuries, disease, and permanent damage to the body is to find ways to change the work process and to minimize or eliminate 1. Recognize features of these risks. ergonomic hand tool design. 2. Describe an KEY TERMS ergonomic tool. cumulative trauma disorder (CTD) injury caused by certain work 3. Select tools based on activities performed every day that mainly affects the knees, back, and design and use. upper extremities, which are shoulders, elbows, wrists, hands ergonomics the study of how the work, the worker, and the workplace 4. Examine current fit together practices and recommend micro-break short break from work or using different muscles or per- forming a different task for a short time to provide rest for fatigued improvements. muscles work-related musculoskeletal disorder (WMSD) injury that usually develops over time, but may have a sudden onset, that mainly affects the muscles, nerves, tendons, ligaments, joints, cartilage, and spinal discs 73 1 Standards for Ergonomic Tools Carpenters use many hand tools, such as, hammers, screwdrivers, pliers, wrenches, and tin snips, plus power tools, such as electric drills, power saws, and screw guns. -
Tool Management
TOOL MANAGEMENT www.haimer-usa.com HAIMER TOOL MANAGEMENT LOGISTICS SYSTEM – OVERVIEW Corner module with perforated wall Connection part shrink fit machine Power Clamp Premium Plus Connection part measuring and balancing system Tool Dynamic Preset Waste disposal module Shelf module folders Assembly station Vertical cabinet universal Tool holder rack 2 Workbench assembly module Corner module with rear wall for storing collets and tools Workbench info module Shelf module parts Magazine cabinet Vertical cabinet tool holders 3 TOOL MANAGEMENT – FOR EFFICIENT WORKING Use: The HAIMER Tool Management completes the HAIMER product program as a sys- tem partner around tool clamping. That means HAIMER offers the complete Tool Management equipment from a single source. As a complete solution for tool pre- setting and tool management, the HAIMER Tool Management provides you with functional and ergonomic criteria for the design of work stations. The storage, setup and management of tools is simplified and optimized by the HAIMER solutions so that efficient working is guaranteed. – Modular room design according to the customer's requirements – Shrinking, balancing and presetting already integrated into the concept – Tidy and isolated solution for concentrated working 4 Technical data subject to change without prior notice CORNER MODULE Corner module with perforated wall Use: The perforated back wall and drawer unit provide a clean and structured workspace. The three integrated LED spots ensure a continually bright and comfortable working atmosphere. Delivery includes: – Corner module with a perforated wall, roof with LED lighting, drawer unit Description Order No. Corner module 4.0 84.802.00.3 Technical data subject to change without prior notice 5 WORKBENCH ASSEMBLY MODULE Picture shows: Assembly module with special configuration, Order No. -
1. Hand Tools 3. Related Tools 4. Chisels 5. Hammer 6. Saw Terminology 7. Pliers Introduction
1 1. Hand Tools 2. Types 2.1 Hand tools 2.2 Hammer Drill 2.3 Rotary hammer drill 2.4 Cordless drills 2.5 Drill press 2.6 Geared head drill 2.7 Radial arm drill 2.8 Mill drill 3. Related tools 4. Chisels 4.1. Types 4.1.1 Woodworking chisels 4.1.1.1 Lathe tools 4.2 Metalworking chisels 4.2.1 Cold chisel 4.2.2 Hardy chisel 4.3 Stone chisels 4.4 Masonry chisels 4.4.1 Joint chisel 5. Hammer 5.1 Basic design and variations 5.2 The physics of hammering 5.2.1 Hammer as a force amplifier 5.2.2 Effect of the head's mass 5.2.3 Effect of the handle 5.3 War hammers 5.4 Symbolic hammers 6. Saw terminology 6.1 Types of saws 6.1.1 Hand saws 6.1.2. Back saws 6.1.3 Mechanically powered saws 6.1.4. Circular blade saws 6.1.5. Reciprocating blade saws 6.1.6..Continuous band 6.2. Types of saw blades and the cuts they make 6.3. Materials used for saws 7. Pliers Introduction 7.1. Design 7.2.Common types 7.2.1 Gripping pliers (used to improve grip) 7.2 2.Cutting pliers (used to sever or pinch off) 2 7.2.3 Crimping pliers 7.2.4 Rotational pliers 8. Common wrenches / spanners 8.1 Other general wrenches / spanners 8.2. Spe cialized wrenches / spanners 8.3. Spanners in popular culture 9. Hacksaw, surface plate, surface gauge, , vee-block, files 10. -
Hammer Drill
Hammer Drill 15 mm (9/16”) MODEL HP1501 004187 DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Model HP1501 Concrete 15 mm (9/16”) Capacities Steel 13 mm (1/2”) Wood 25 mm (1”) No load speed (RPM) 0 - 2,800/min. Blows per minute 0 - 44,800 Overall length 299 mm (11-3/4”) Net weight 1.7 kg (3.7 lbs) • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 3. Keep bystanders, children, and visitors away while operating a power tool. Distrac- 1. Keep your work area clean and well lit. tions can cause you to lose control. Cluttered benches and dark areas invite acci- dents. Electrical Safety 2. Do not operate power tools in explosive 4. Double insulated tools are equipped with atmospheres, such as in the presence of a polarized plug (one blade is wider than flammable liquids, gases, or dust. Power the other.) This plug will fit in a polarized tools create sparks which may ignite the dust outlet only one way. If the plug does not fit or fumes. fully in the outlet, reverse the plug. If it still does not fit, contact a qualified elec- 2 trician to install a polarized outlet. Do not 13. -
HAMMERS DEMOLITION HAMMER BITS CHART 1-1/8” Hex Shank Makita Large Shank Makita Small Shank D15 D14 D13 D12 D9 D7 D5 D4 D3 D2 D1 D7 D5 D4 D3 D2 D1 D10 D8 D3 D1
HAMMERS DEMOLITION HAMMER BITS CHART 1-1/8” Hex Shank Makita Large Shank Makita Small Shank D15 D14 D13 D12 D9 D7 D5 D4 D3 D2 D1 D7 D5 D4 D3 D2 D1 D10 D8 D3 D1 Makita HM1304B HM1810 Large Makita 1-1/8” Small Hex HM1500 HK1810 SDS Plus Shank SDS Max Shank 3/4” Hex Shank D10 D8 D3 D2 D1 HK1820 D9 D7 D6 D5 D4 D3 D2 D1 D16 D11 D9 D7 D6 D5 D4 D3 D2 D1 SDS max HK1820L 3/4” Hex 21/32” SDS Round Shank Plus HM0860C HM1100C HM1202C HK0500 HM1211B ROTARY HAMMER BITS CHART SDS PLUS SHANK HR3210C R1 HR3210FCT R8 IS ADAPTER WHICH ALLOWS OLDER TOOLS TO USE DEMOLITION BITS R6 HR2811F Metal R3 R2 HR3000C Wood R4 SDS Plus HR2432 D1 R23c R23b R23 R23a HR2455 R9 R8 R10 HR2470F / FT HR160DWA & HR2400 only SDS MAX SHANK D4 R1a HR5210C D5 HR5211C D1 D11 D6 HR4010C SDS HR4011C D2 HR4510C D16 D15 max HR4511C SDS Max D18 D9 D3 HR4002 R24c R24b R24 R24a HR4500C SPLINE SHANK & 3/4” HEX SHANK 21/32” Round Shank D4 D2 3/4” HEX Shank 21/32” Round Shank D5 D3 HR3851 D8 D6 R6 D7 HR4040C R1b D1 D18 D17 R24a R24c R24b R24 D16 HR5000 Taper Shank R5 Spline Shank 67 HAMMERS DEMOLITION HAMMER BITS CHART Demolition Hammer Bits Chart HM1202C, HM1100C, HR3210C/FCT, HM0860C, HR5210C, HR3000C, HR2811F, HR5211C, HR4510C, HM1810C, HM1304B HM1500 HK1810 HR2455, HR2432, Model HR4511C, HR4500C, HR2470F/FT, HK1820, HR4010C, HR4011C, HK0500 HR4002 Ref. No. Description 1-1/8" Hex 3/4" Hex Makita Large Makita Small SDS Plus 3/4" Hex, 21/32" Round SDS Max Hex Shank Size Part No. -
The Leading Manufacturer of Forged Hand and Power Tools Accessories Since 1946
122806_A_AJAX_ATW-lisa 7/17/12 8:20 PM Page 1 The Leading Manufacturer of Forged Hand and Power Tools Accessories Since 1946 TM Phone: 800.323.9129 • Fax: 800.424.2529 122806_A_AJAX_r3.qxp_AJAX 7/25/12 11:59 AM Page 3 Phone: 800.323.9129 • Fax: 800.424.2529 www.ajaxtools.com ZIP GUN CHISELS & ACCESSORIES WELD FLUX CHISELS & ACCESSORIES CHIPPING HAMMER TOOLS & ACCESSORIES BERYLLIUM COPPER SAFETY TOOLS RIVET BUSTER TOOLS & ACCESSORIES PAVING BREAKER TOOLS DRILL STEEL TOOLS ELECTRIC HAMMER TOOLS RIGGER TOOLS HAND TOOLS WEDGES, LINE UP PINS & SCRAPERS DEMOLITION TOOLS TM Wear Safety Goggles 4 122806_A_AJAX_ATW-lisa 7/17/12 8:20 PM Page 5 23⁄8" 3 .495" 111⁄16" .495" 2 ⁄8" 60mm 51⁄64" 15⁄16" 60mm 13⁄4" 17 ⁄32" .485" 44.4mm .580" 15⁄32" .469" 14.7mm .576" .680" .680" .576" 17.2mm 17.2mm .812" .812" 3 3 20.6mm 2 ⁄8" 3⁄8" 13 9 20.6mm 23⁄8" ⁄8" 60.3mm ⁄16" ⁄16" .495" 19⁄32" 29⁄32" 9.5mm 9.5mm 60.3mm 3 4 1⁄2" sq. 1⁄4" 1⁄4" 1 ⁄ " .360" Ø .415" 44.4mm .580" .425" 1 14.7mm Ø .373" .576" 1 ⁄8" .680" 13⁄16" 11⁄8" 13⁄16" 28.5mm 17.2mm 20.6mm 28.5mm 20.6mm 21⁄2" 1 4 21⁄2" 11⁄4" 1 5 1 ⁄ " 3⁄8" 63.5mm 3 1 ⁄4" REF 1 ⁄64" 32mm 63.5mm 32mm ⁄8" .620" 9.5mm 13⁄4" 9.5mm .354" .919" 1" 3⁄8" .375" .610" 44.4mm 13 13 .576" .680" -
How to Use Tools / Mistakes to Avoid CARLTSOE SAFETY TOOLS
CARLTSOE SAFETY TOOLS If you just had the right tools How to Use Tools / Mistakes to Avoid Tool Proper Uses Abuse/Misuse Nail Hammers Nail hammers are intended for driving and pulling common, Never strike one hanmmer with or against another hammer unhardened nails only, and for ripping apart wooden or a hatchet. Never strike nail pullers, steel chisels or structures. They may be used to strike nail sets with the other hardened objects with a nail hammer as the face may center of the striking face. chip, possibly resulting in eye or other serious injury. Ball Pein Hammers Ball pein hammers of the proper size are designed for striking chisels and punches, and for riveting, shaping and Strike squarely and avoid glancing blows that may cause straightening unhardened metal. the edge of the face to chip, possibly resulting in eye or When striking a struck tool (chisel or punch), the striking face other serious injury. Never strike with or against the side, of the hammer should have a diameter at least 3/8" larger or cheek, of any hammer. than the struck face of the tool. Riveting and Setting Hammers The Riveting hammer is designed for driving and spreading Never use these special-purpose hammers for general- rivets on sheet metal work. The Setting hammer is designed purpose work. The square, sharp edges of the setting for forming sharp corners, closing and peining seams and lock hammer make it vulnerable to chipping if improperly used. edges, and for use by glaziers for inserting glazier points. Never strike against other steel tools. -
Tools for Tile & Stone Catalog
TOOLS FOR TILE & STONE CONTRACTORS CUTTING, PROFILING & POLISHING TH Since 1986 Celebrating 35 Years Providing Better Solutions to the Professional VERSION 6 CONTACT US WELCOME Alpha Professional Tools® was founded in 1986 and has become a leading manufacturer of quality tools for professionals in the natural/engineered stone, porcelain, ceramic, glass, construction, marine and automotive industries. Alpha® provides the best products for cutting, drilling, shaping and polishing all types of materials. In addition to providing the best products in the industry, Alpha Professional Tools® offers a variety of services to support their products. Company Contact Information: Headquarters & 16 Park Drive Training Center: Franklin, NJ 07416 Hours of Operation (EST): 8:30 a.m. - 5:00 p.m. Telephone No: 201-337-3343 Toll-Free No: 800-648-7229 Fax No: 201-337-2216 Toll Free Fax No: 800-286-0114 E-mail Orders to: Contact Us: [email protected] www.alpha-tools.com [email protected] [email protected] Follow Us: Sales Contacts by Territory – [email protected] Caribbean 201-337-3343 Ohio Valley 440-364-3759 Canada 519-546-9861 Pacific 800-648-7229 International 201-337-3343 South 480-848-6808 Midwest 630-849-7105 Southeast 678-977-1147 Northeast 973-830-7681 Southern CA 925-428-1292 Northern CA 925-428-1292 TABLE OF CONTENTS TOOLS STONE CUTTER • ESC-125, Wet Stone Cutter .......................................................................................2 • Countertop Trim Kit ....................................................................................................4