View the Instruction Booklet (PDF)

5 6 Additional Notes What if you have a bed skirt? The To Use Close the BedMaker If you have a bed skirt that covers the surface of the box spring with Just lift! IMPORTANT: You must lift the top fabric, it helps to pin it down right BedMaker™ 1 plate slightly before collapsing the where the BedMakers sit. Otherwise, BedMaker, to take the weight of the even if you stick the BedMaker to mattress off the foot stand and allow the the bed skirt, both can still ride The foot stand drops into place with it to come out of the slot. up and slide around, since the bed a click, holding the mattress up. If Method 1: With two hands skirt is not attached to anything. Holds the you do not hear a click, lift higher. 1. Lift Bed skirt pins work well for this Keep your hand at the edge; no (links on website). Other options are mattress up need to reach under the mattress. 2. Push to remove the bed skirt altogether, Make the bed and tuck the or replace it with a wrap-around model that does not cover the 2 sheets in between the upper and lower plates of the BedMaker. surface of the bed base (links on Lower into closed position. website). What if there is a rim around the bedsheets bed frame? mattress This is no problem. Place the Method 2: With one hand BedMakers at the corners to give box spring your hand the most room to slide in ...while you 1. Lift past the rim. Optionally, if the rim is 2. Push heel of hand very deep, adding a box spring can change the sheets. Remember, the BedMaker stays on elevate the mattress for easier the bed, so you don't have to access. remove it. Tuck the sheets right into it, then close it as in step 6. With palm facing up, lift with heel of Should you put the BedMaker hand, and close with fingertips. over or under the mattress Caution protector? Instructions Lower into closed position. It's up to you, but if you don't Take care not to pinch fingers in the device. change the mattress protector often, for Use Keep fingers flat and operate from edge of bed; do not reach far under mattress. Liability you can leave it outside the limited to purchase price of product. Load limit BedMaker. Let the mattress protector of 50 lbs; not designed to sit or lean on. Not Leave the BedMaker on the bed, remain above the top plate of the responsible for breakage due to application of ready for the next use. BedMaker, hugging the mattress. weight in excess of limit. 613-400-1511 Patent Pending The BedMakerTM 2 3 4 Congratulations on purchasing the BedMaker! With this tool you will Decide on location Place on bed Stick down never stuggle with a heavy mattress BedMakers can be placed anywhere Pull back the bedsheets to expose IMPORTANT: Stick each BedMaker again. along the edge of the bed frame. A the bare mattress or mattress down using its adhesive pad. Do not practical configuration is with the two protector. skip this step! It keeps the BedMaker bottom BedMakers angled diagonally from sliding around under the mattress, 1 and helps the foot stand engage at the corners, and the two top properly in the slot. Try it out! BedMakers placed horizontally on the side of the bed, just in front of any Note: If you have a bed skirt, When you open the package, take bedside tables. pin it down now, before sticking out one BedMaker and try it out in the BedMakers to it. See details Bedside your hand. Remove the elastic band Table on reverse side. (carefully due to the spring), and open the BedMaker. Notice how the Remove the backing paper from the foot stand "clicks" into the slot. Push BedMaker adhesive pad, and press the BedMaker BedMaker firmly down onto the base of the bed, it back out of the slot again to close Bed Foot Head contacting as much of a slat, rung, or it. BedMaker Slide the closed BedMaker in between solid part of the bed base as possible. the mattress and box spring. Rest the BedMaker back (hinge end) across a solid part Bedside Table of the bed base, such as a slat, and the front on or near the edge of the The hinges of the BedMakers face bed frame. inward towards the center of the bed, with the gap opening at the edge of the bed. mattress The pads have a velcro layer - this is so that you can remove the BedMaker if needed, without pulling off the box spring adhesive. This can be useful when moving the bed frame to a new room or Try it out a few times to ensure it's house, for example. But most of the Now let's place it on a bed. resting solidly, then stick it down with time you just leave the velcro stuck together. the adhesive pads (step 4)..

Load more