DOCSLIB.ORG

ISL94216 Datasheet

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
ISL94216 Datasheet Datasheet ISL94216 16-Cell Battery Front End The ISL94216 is a 16-cell Battery Front End (BFE) IC, Features an essential component of any Battery Management • High hot plug rating: 62V System (BMS), which periodically scans battery status and the operating environment to optimize •VCELL accuracy: ±5mV battery life and prevent catastrophic failures. •IPACK accuracy: ±0.2% A differential multiplexer and 16-bit ADC allows for • 16-bit VCELL and IPACK measurements accurate monitoring of cell voltage, temperature, and • Charge/Load wakeup detection circuitry load current for management of the overall state of the battery pack. • 4-pin GPIO port The ISL94216 supports I2C, SPI, and Single Wire • Integrated 3.3V regulator protocols allowing customers to connect an MCU in a • Supports I2C, SPI, and Single Wire communications proprietary battery management solution. Low current consumption with an average IDLE mode Applications current of 200µA and a SHIP mode current of less • Light electric vehicles such as e-bikes, e-scooters, than 18µA maximizes the storage and discharge life and e-motorcycles of a battery pack. • Cordless power and gardening tools The ISL94216 features internal cell balancing circuitry • Home appliances that provides 8mA of balance current per cell. External cell balancing for higher currents is also • 24V, 36V, 42V, and 48V portable battery packs supported. • Telecom and server farms This 16-cell high voltage BFE IC is offered in an •Solar farms efficient 64 Ld QFN package with a thermal pad. • Energy storage systems FN8936 Rev.3.00 Page 1 of 139 Sep 1, 2021 © 2020 Renesas Electronics ISL94216 Contents 1. Overview . 4 1.1 Typical Application . 4 1.2 Block Diagram . 5 1.3 Ordering Information . 6 1.4 Pin Configurations . 7 1.5 Pin Descriptions . 7 2. Specifications . 10 2.1 Absolute Maximum Ratings . 10 2.2 Thermal Information . .11 2.3 Recommended Operation Conditions . .11 2.4 Electrical Specifications . 12 3. Typical Performance Curves . 21 4. System Registers . 34 4.1 IC Device Details . 37 4.2 Global IC Controls . 37 4.3 VCELL and IPACK Measurement . 39 4.4 VCELL Fault Detectors . 44 4.5 IPACK Fault Detectors . 47 4.6 ETAUX Port . 54 4.7 0x12 ALRT and GPIO . 55 4.8 ETAUX Detectors . 57 4.9 Internal Temperature . 59 4.10 Regulator Measurements and Detectors . 60 4.11 VBAT1 . 64 4.12 Power FET Block . 68 4.13 Cell Balancing Registers . 71 4.14 System Faults and Status . 77 5. Pin Functionality . 88 5.1 VCn Pins . 88 5.2 CBn Pins . 88 5.3 CSP and CSN Pins (24, 25) . 89 5.4 VSS Pin (26) . 90 5.5 AUX0/xT0, VTEMP, AUX1/xT1 Pins (27, 29, 28) . 90 5.6 Regulator and Supply Pins (30-33) . 91 5.7 CMS0 and CMS1 Pins (34, 35) . 92 5.8 DGND Pin (36) . 92 5.9 V2P5 Pin (37) . 92 5.10 RESET Pin (38) . 92 5.11 WAKEUP Pin (39) . 93 5.12 ALRT Pin (40) . 93 5.13 ADDR/CS Pin (41) . 93 5.14 SCL Pin (42) . 93 5.15 MOSI Pin (43) . 93 5.16 MISO/SDA/SINGLE-WIRE Pin (44) . 93 5.17 GPIO(0-3) Pin (45-48) . 94 FN8936 Rev.3.00 Page 2 of 139 Sep 1, 2021 ISL94216 5.18 LDMON Pin (49) . 94 5.19 CFET and DFET Pins (50, 51) . 95 5.20 VCPMP Pin (52) . 97 5.21 VBAT2 Pin (53) . 97 5.22 VBAT1 Pin (54) . ..
Load more

Recommended publications
  • NIST Time and Frequency Services (NIST Special Publication 432)
    Time & Freq Sp Publication A 2/13/02 5:24 PM Page 1 NIST Special Publication 432, 2002 Edition NIST Time and Frequency Services Michael A. Lombardi Time & Freq Sp Publication A 2/13/02 5:24 PM Page 2 Time & Freq Sp Publication A 4/22/03 1:32 PM Page 3 NIST Special Publication 432 (Minor text revisions made in April 2003) NIST Time and Frequency Services Michael A. Lombardi Time and Frequency Division Physics Laboratory (Supersedes NIST Special Publication 432, dated June 1991) January 2002 U.S. DEPARTMENT OF COMMERCE Donald L. Evans, Secretary TECHNOLOGY ADMINISTRATION Phillip J. Bond, Under Secretary for Technology NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY Arden L. Bement, Jr., Director Time & Freq Sp Publication A 2/13/02 5:24 PM Page 4 Certain commercial entities, equipment, or materials may be identified in this document in order to describe an experimental procedure or concept adequately. Such identification is not intended to imply recommendation or endorsement by the National Institute of Standards and Technology, nor is it intended to imply that the entities, materials, or equipment are necessarily the best available for the purpose. NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY SPECIAL PUBLICATION 432 (SUPERSEDES NIST SPECIAL PUBLICATION 432, DATED JUNE 1991) NATL. INST.STAND.TECHNOL. SPEC. PUBL. 432, 76 PAGES (JANUARY 2002) CODEN: NSPUE2 U.S. GOVERNMENT PRINTING OFFICE WASHINGTON: 2002 For sale by the Superintendent of Documents, U.S. Government Printing Office Website: bookstore.gpo.gov Phone: (202) 512-1800 Fax: (202)
    [Show full text]
  • Radio Navigational Aids
    RADIO NAVIGATIONAL AIDS Publication No. 117 2014 Edition Prepared and published by the NATIONAL GEOSPATIAL-INTELLIGENCE AGENCY Springfield, VA © COPYRIGHT 2014 BY THE UNITED STATES GOVERNMENT NO COPYRIGHT CLAIMED UNDER TITLE 17 U.S.C. WARNING ON USE OF FLOATING AIDS TO NAVIGATION TO FIX A NAVIGATIONAL POSITION The aids to navigation depicted on charts comprise a system consisting of fixed and floating aids with varying degrees of reliability. Therefore, prudent mariners will not rely solely on any single aid to navigation, particularly a floating aid. The buoy symbol is used to indicate the approximate position of the buoy body and the sinker which secures the buoy to the seabed. The approximate position is used because of practical limitations in positioning and maintaining buoys and their sinkers in precise geographical locations. These limitations include, but are not limited to, inherent imprecisions in position fixing methods, prevailing atmospheric and sea conditions, the slope of and the material making up the seabed, the fact that buoys are moored to sinkers by varying lengths of chain, and the fact that buoy and/or sinker positions are not under continuous surveillance but are normally checked only during periodic maintenance visits which often occur more than a year apart. The position of the buoy body can be expected to shift inside and outside the charting symbol due to the forces of nature. The mariner is also cautioned that buoys are liable to be carried away, shifted, capsized, sunk, etc. Lighted buoys may be extinguished or sound signals may not function as the result of ice or other natural causes, collisions, or other accidents.
    [Show full text]
  • Interstate Commerce Act 49 App
    Interstate Commerce Act 49 App. u.s.c. § 1 et seg. (1988) The Interstate commerce Act was partially repealed and recodified in 1978. However, according to Public Law No. 95-473, § 4(c): 92 stat. 1466-1470 (1978), those portions of the old_ICA that were repealed and recodified in 1978, nevertheless remain in effect as they existed on October 1, 1977, to the extent that these laws relate to the movement of oil by pipeline and the rates and charges related thereto. The ICA related to oil pipeline regulation is found as an appendix to Title 49 of the United States Code, and was reprinted in the second edition of Volume I of Staff's Oil Pipeline Handbook. However, the U.S. Code 1988 edition is the last to include the appendix. Although the appendix still applies to oil pipeline regulation, it was, for unknown reasons, excluded from the 1994 edition of the u.s. Code. Therefore, we are reprinting it in this volume. Interstate Commerce Act 49 App. u.s.c. § 1 et seq. (1988) TITLE .t9. APPE.SDIX-TRANSPORTATIO.S . di.x consists of sections of former Title 49 that were not included in Title 49 as enacted Tlus A~e; L 95 _473 and Pub. L. 97-449, and certain laws related to transportation that were en­ bY · l~r Pub L. 95-473. Sections /rom former Title 49 retain the same section numbers in :-f:~~endiz. 'For d~.sp.osition of all sections of former Title 49, see Table at beginning ot Title 49, Transportatlon. Sec.
    [Show full text]
  • STANDARD FREQUENCIES and TIME SIGNALS (Question ITU-R 106/7) (1992-1994-1995) Rec
    Rec. ITU-R TF.768-2 1 SYSTEMS FOR DISSEMINATION AND COMPARISON RECOMMENDATION ITU-R TF.768-2 STANDARD FREQUENCIES AND TIME SIGNALS (Question ITU-R 106/7) (1992-1994-1995) Rec. ITU-R TF.768-2 The ITU Radiocommunication Assembly, considering a) the continuing need in all parts of the world for readily available standard frequency and time reference signals that are internationally coordinated; b) the advantages offered by radio broadcasts of standard time and frequency signals in terms of wide coverage, ease and reliability of reception, achievable level of accuracy as received, and the wide availability of relatively inexpensive receiving equipment; c) that Article 33 of the Radio Regulations (RR) is considering the coordination of the establishment and operation of services of standard-frequency and time-signal dissemination on a worldwide basis; d) that a number of stations are now regularly emitting standard frequencies and time signals in the bands allocated by this Conference and that additional stations provide similar services using other frequency bands; e) that these services operate in accordance with Recommendation ITU-R TF.460 which establishes the internationally coordinated UTC time system; f) that other broadcasts exist which, although designed primarily for other functions such as navigation or communications, emit highly stabilized carrier frequencies and/or precise time signals that can be very useful in time and frequency applications, recommends 1 that, for applications requiring stable and accurate time and frequency reference signals that are traceable to the internationally coordinated UTC system, serious consideration be given to the use of one or more of the broadcast services listed and described in Annex 1; 2 that administrations responsible for the various broadcast services included in Annex 2 make every effort to update the information given whenever changes occur.
    [Show full text]
  • Time and Frequency Users' Manual
    ,>'.)*• r>rJfl HKra mitt* >\ « i If I * I IT I . Ip I * .aference nbs Publi- cations / % ^m \ NBS TECHNICAL NOTE 695 U.S. DEPARTMENT OF COMMERCE/National Bureau of Standards Time and Frequency Users' Manual 100 .U5753 No. 695 1977 NATIONAL BUREAU OF STANDARDS 1 The National Bureau of Standards was established by an act of Congress March 3, 1901. The Bureau's overall goal is to strengthen and advance the Nation's science and technology and facilitate their effective application for public benefit To this end, the Bureau conducts research and provides: (1) a basis for the Nation's physical measurement system, (2) scientific and technological services for industry and government, a technical (3) basis for equity in trade, and (4) technical services to pro- mote public safety. The Bureau consists of the Institute for Basic Standards, the Institute for Materials Research the Institute for Applied Technology, the Institute for Computer Sciences and Technology, the Office for Information Programs, and the Office of Experimental Technology Incentives Program. THE INSTITUTE FOR BASIC STANDARDS provides the central basis within the United States of a complete and consist- ent system of physical measurement; coordinates that system with measurement systems of other nations; and furnishes essen- tial services leading to accurate and uniform physical measurements throughout the Nation's scientific community, industry, and commerce. The Institute consists of the Office of Measurement Services, and the following center and divisions: Applied Mathematics
    [Show full text]
  • MSF Signal Technical Data
    NPL Time & Frequency Services MSF 60 kHz Time and Date Code Carrier on Second 00 Minute marker 0 ms 500 ms Seconds 01-59 † bit A bit B Second marker Carrier off 0 ms 100 ms 200 ms 300 ms The two bits, numbered xxA and xxB for second xx bit polarity: 0=on, 1=off † Most minutes have 60 seconds numbered 00-59; exceptionally a UTC minute can have 61 seconds with the extra second being numbered 60 (a positive leap second), or 59 seconds (a negative leap second). The MSF transmission from Anthorn (latitude 54° 55' N, longitude 3° 15' W) is the principal means of disseminating the UK national standards of time and frequency which are maintained by the National Physical Laboratory. The effective monopole radiated power is 15 kW and the antenna is substantially omnidirectional. The signal strength is greater than 10 mV/m at 100 km and greater than 100 V/m at 1000 km from the transmitter. The signal is widely used in northern and western Europe. The carrier frequency is maintained at 60 kHz to within 2 parts in 1012. The MSF time and date code format is summarised in the diagrams above. Simple on-off carrier modulation is used, the rise and fall times of the carrier are determined by the combination of antenna and transmitter. The timing of these edges is governed by the seconds and minutes of Coordinated Universal Time (UTC), which is always within 0.9 seconds of Universal Time (UT1), an astronomical time scale based on the Earth’s rotation descended from Greenwich Mean Time (GMT).
    [Show full text]
  • Improving Dut1 from VLBI Intensive Sessions with GRAD Gradients and Ray-Traced Delays
    Available online at www.sciencedirect.com ScienceDirect Advances in Space Research 63 (2019) 3429–3435 www.elsevier.com/locate/asr Improving dUT1 from VLBI intensive sessions with GRAD gradients and ray-traced delays Daniel Landskron ⇑, Johannes Bo¨hm Technische Universita¨t Wien, Vienna, Austria Received 5 December 2018; received in revised form 21 March 2019; accepted 26 March 2019 Available online 3 April 2019 Abstract Exact knowledge of the angle of Earth rotation UT1 with respect to coordinated time UTC, dUT1, is essential for all space geodetic techniques. The only technique which is capable of determining dUT1 is Very Long Baseline Interferometry (VLBI). So-called Intensive VLBI sessions are performed on a daily basis in order to provide dUT1. Due to the reduced geometry of Intensive sessions, there is how- ever no possibility to estimate tropospheric gradients from the observations, which limits the accuracy of the resulting dUT1 signifi- cantly. This paper deals with introducing the information on azimuthal asymmetry from external sources, thus attempting to improve the dUT1 estimates. We use the discrete horizontal gradients GRAD and the empirical horizontal gradients GPT3 as well as ray-traced delays from the VieVS ray-tracer for this purpose, which can all be downloaded from the VMF server of TU Wien (http://vmf.geo.tuwien.ac.at). The results show that this strategy indeed improves the dUT1 estimates when compared to reference values from multi-station VLBI stations, namely by up to 15%. When converted to length-of-day (LOD), the estimates can be compared to LODs from global analyses of Global Navigation Satellite Systems (GNSS).
    [Show full text]
  • Determination of Earth Rotation by Combining Vlbi and Ring Laser Observations
    DETERMINATION OF EARTH ROTATION BY COMBINING VLBI AND RING LASER OBSERVATIONS T. NILSSON, J. BOHM,¨ H. SCHUH Institute of Geodesy and Geophysics Vienna University of Technology, Vienna, Austria e-mail: [email protected] ABSTRACT. We investigate the potential of combining VLBI data with ring laser gyroscope measure- ments. The formal errors of polar motion and UT1-UTC obtained from such a combination are estimated as function of the ring laser measurement accuracy. The possible improvements obtained by using data from three globally distributed ring lasers, instead of only one, is also investigated. It is shown that if three globally distributed ring lasers are used – all being one order of magnitude more accurate than the current Wettzell ring laser – the formal errors of the estimated Earth rotation parameters are reduced by more than 50%, compared to a VLBI only solution. 1. INTRODUCTION In recent years large and very sensitive ring laser gyroscopes have been constructed which are able to measure the rotation of the Earth (Schreiber et al., 2009, 2011). Presently the ring laser accuracy is about one order of magnitude worse compared to space geodetic techniques such as Very Long Baseline Interferometry (VLBI) (Nilsson et al., 2012), but the accuracy is increasing rapidly (Schreiber et al., 2011). Common problems in ring lasers observations are however unknown offsets and drifts, making it difficult to obtain the absolute Earth rotation vector and its long term variations. The strength of the ring laser data is mainly to observe the high frequency variations, e.g. at sub-daily periods. Furthermore, since one single ring laser is only sensitive to one component of the Earth rotation vector, at least three ring lasers (with different orientation) would be needed in order to get all Earth rotation parameters.
    [Show full text]
  • Time and Frequency Users Manual
    A 11 10 3 07512T o NBS SPECIAL PUBLICATION 559 J U.S. DEPARTMENT OF COMMERCE / National Bureau of Standards Time and Frequency Users' Manual NATIONAL BUREAU OF STANDARDS The National Bureau of Standards' was established by an act of Congress on March 3, 1901. The Bureau's overall goal is to strengthen and advance the Nation's science and technology and facilitate their effective application for public benefit. To this end, the Bureau conducts research and provides: (1) a basis for the Nation's physical measurement system, (2) scientific and technological services for industry and government, (3) a technical basis for equity in trade, and (4) technical services to promote public safety. The Bureau's technical work is per- formed by the National Measurement Laboratory, the National Engineering Laboratory, and the Institute for Computer Sciences and Technology THE NATIONAL MEASUREMENT LABORATORY provides the national system of physical and chemical and materials measurement; coordinates the system with measurement systems of other nations and furnishes essential services leading to accurate and uniform physical and chemical measurement throughout the Nation's scientific community, industry, and commerce; conducts materials research leading to improved methods of measurement, standards, and data on the properties of materials needed by industry, commerce, educational institutions, and Government; provides advisory and research services to other Government agencies; develops, produces, and distributes Standard Reference Materials; and provides
    [Show full text]
  • Ultra-Rapid Dut1-Observations with E-Vlbi
    ARTIFICIAL SATELLITES, Vol. 45, No. 2 – 2010 DOI: 10.2478/v10018-010-0007-6 ULTRA-RAPID DUT1-OBSERVATIONS WITH E-VLBI R. Haas Chalmers University of Technology, Onsala Space Observatory, Sweden e-mail: [email protected] M.Sekido,T.Hobiger,T.Kondo National Institute of Information and Communications Technology, Japan e-mail: [email protected], [email protected], [email protected] S. Kurihara, D. Tanimoto, K. Kokado Geographical Survey Institute,Japan e-mail: [email protected], [email protected], [email protected] J. Wagner, J. Ritakari, A. Mujunen Mets¨ahovi Radio Observatory, Aalto University, Finland e-mail: [email protected], [email protected], [email protected] ABSTRACT. We give a short overview about the achievements of the Fennoscandian- Japanese ultra-rapid dUT1-project that was initiated in early 2007. The combination of real-time data transfer, near real-time data conversion and correlation, together with near- real time data analysis allows to determine dUT1 with a very low latency of less than 5 minutes after the end of a VLBI-session. The accuracy of these ultra-rapid dUT1-results is on the same order than the results of the standard rapid-service of the International Earth Rotation and Reference Frame Service (IERS). The ultra-rapid approach is currently extended to 24 hour sessions and is expected to become an important contribution for the future next generation VLBI system called VLBI2010. Keywords: Very Long Baseline Interferometry, Earth orientation, dUT1-observations, e-VLBI, VLBI2010 1. INTRODUCTION The orientation of the earth is variable on a wide range of time scales.
    [Show full text]
  • Synchronizing Time with Dcf77 and Msf60
    SYNCHRONIZING TIME WITH DCF77 AND MSF60 In many of the applications that use the H0420 and Starling programmable audio controllers/players, clock synchronization is a requirement. This is especially the case with the H0420, because it lacks a battery backup for its internal real-time clock —hence, when there is a power drop-out (even for less than a second), the H0420 resets to 1 January 1970 at 00:00 hours. Even with a backup battery for the real-time clock, when the device is used outdoor, you may observe the clock on the H0420 or Starling to deviate from the true time. The reason is that the crystals used for timekeeping are calibrated for use at room temperature. The time that the device resets to after power-up, of 1 January 1970 at 00:00 hours, is the "start of the Unix era". This is a commonly used basis for time keeping in operating systems and embedded devices; see the Wikipedia article in the references. For keeping the time of the H0420/Starling accurate, there are two options: get the time from the network (a typical option for the Starling, as it has a network port), or get the time from some other source, such as a radio signal. This latter option is suitable when no network is available at the location, which is common in outdoor use. This article specifically discusses how to pick up the current "time of the day" from DCF77 signal, but also discusses MSF60. A particular advantages of synchronizing on a time signal radio station is that "daylight saving time" is automatically handled.
    [Show full text]
  • Prison Population Forecast for Washington State
    -'----",----- --...,.,-----,,--...,,--~~------~--- ,----' ---''''--- ;:£.t::: ~,~- ., \ ~"'-.' -;- - () " 0 (J (') ~~.:,::" ,"W:;;'_':;;"-_"'~_1.,_'_' --'"-' .),':':=-"::::"-'-""'~=.===~."'p """"'" .~ .... ~ •• - ....... ~~~"'.... '~...... - ........... '-' ~.>- ~ .. _.~," . "--.'~' . if- - D a ' .'~ C a (. 0 i~ . ~I ,;) " National Criminal Justice Reference Service a Q " (1 , '--------------'nCJrs :1 This microfiche was produced from documents received for , ~ 0 ,lnclusion in the NCJRS data base. Since NCJRS cannot exercise 'control over the physical condition of the documents submitted, (.') c ~l ': 0 ~ the individual frame quality will vary. The resolution chart on Q d . .. ~ 0 this frame may be used to evaluate the document quality. ~l, "PRISON POPQiLATIONoFORECAST 0 ·:FOR··WASH~l'iGTON STAT'E~FY ·t'982-'i995:~ .' TECHNICAL PROGRAMMIN°G 0 0 I 111. I DO~~ENTATION . [ o I 1.1 "0 ;"(ll c, c~o 111111.25 111111.4 tllll/.6 I '" ~ 0 I o· ! -~ " 1, '" 1 I \ o MICROCOPY RESOLUTION TE~T CHART NATIONAL BUREAU OF STANDARDS-1963-A Preparedo for • ~---------:----; Governor's Interagency Criminal" Justice Q Work Group. e <J o ~ ._ by the _ Microfilming procedures us~d to cr~eate this fiche comply with o Office of Financial Management the standards set forth in 41CFR 101-11.504. Division of Forecasting & Estimation Points of view or opinions stated in this document are those of the author(s) and do not represent the official­ position or, policies of the U. S. Depat1ment of Justice. .\ Q!'J 2/10/.83 . National Institute of Justice " 'f ~, July ,1982= {\ ., I United States Department of Justicle 0::; (? .. Washington, D. C. 20531 .' . ('~ ,,_,. ...;M..- ~ It' "'~.:~- -... o o ./ . ... : . ~~------~- - -----------------------......---------~--------.,::;,~t_.~.~:_.. _~=~~_:._~.~_~ o STA1.""E OF WASHiNGTON o John Spellman, Governor ]PRISON POPUILATION FORECAST or, FOIffi, WA§JHIINGTON §TATlE=FY 1982=1995~ \ TECHNICAL PROGRAMMING DOCUMENTATION .' {.
    [Show full text]