Safety Data Sheet

Total Page:16

File Type:pdf, Size:1020Kb

Safety Data Sheet SAFETY DATA SHEET Revision Date 29-Feb-2020 Revision Number 3 1. Identification Product Name Spectroflux 135, Lithium tetraborate, Lithium fluoride, Strontium oxide & Vanadium(V) oxide, 84.9:8.4:4.6:2.1 w/w% Cat No. : 12091 Synonyms No information available Recommended Use Laboratory chemicals. Uses advised against Food, drug, pesticide or biocidal product use. Details of the supplier of the safety data sheet Company Alfa Aesar Thermo Fisher Scientific Chemicals, Inc. 30 Bond Street Ward Hill, MA 01835-8099 Tel: 800-343-0660 Fax: 800-322-4757 Email: [email protected] www.alfa.com Emergency Telephone Number During normal business hours (Monday-Friday, 8am-7pm EST), call (800) 343-0660. After normal business hours, call Carechem 24 at (866) 928-0789. 2. Hazard(s) identification Classification This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200) Acute oral toxicity Category 4 Skin Corrosion/Irritation Category 2 Serious Eye Damage/Eye Irritation Category 1 Germ Cell Mutagenicity Category 2 Carcinogenicity Category 2 Reproductive Toxicity Category 2 Specific target organ toxicity - (repeated exposure) Category 2 Target Organs - Respiratory system. Label Elements Signal Word Danger ______________________________________________________________________________________________ Page 1 / 8 Spectroflux 135, Lithium tetraborate, Lithium fluoride, Revision Date 29-Feb-2020 Strontium oxide & Vanadium(V) oxide, 84.9:8.4:4.6:2.1 w/w% ______________________________________________________________________________________________ Hazard Statements Harmful if swallowed Causes skin irritation Causes serious eye damage May cause respiratory irritation Suspected of causing genetic defects Suspected of causing cancer Suspected of damaging the unborn child May cause damage to organs through prolonged or repeated exposure Precautionary Statements Prevention Obtain special instructions before use Do not handle until all safety precautions have been read and understood Use personal protective equipment as required Wash face, hands and any exposed skin thoroughly after handling Do not eat, drink or smoke when using this product Do not breathe dust/fume/gas/mist/vapors/spray Response IF exposed or concerned: Get medical attention/advice Skin IF ON SKIN: Wash with plenty of soap and water If skin irritation occurs: Get medical advice/attention Take off contaminated clothing and wash before reuse Eyes IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing Immediately call a POISON CENTER or doctor/physician Ingestion IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell Rinse mouth Storage Store locked up Disposal Dispose of contents/container to an approved waste disposal plant Hazards not otherwise classified (HNOC) Contact with acids liberates very toxic gas WARNING. Cancer - https://www.p65warnings.ca.gov/. 3. Composition/Information on Ingredients Component CAS-No Weight % Boron lithium oxide (B4Li2O7) 12007-60-2 84.9 Lithium fluoride 7789-24-4 8.4 Strontium oxide (SrO) 1314-11-0 4.6 Vanadium pentoxide 1314-62-1 2.1 4. First-aid measures ______________________________________________________________________________________________ Page 2 / 8 Spectroflux 135, Lithium tetraborate, Lithium fluoride, Revision Date 29-Feb-2020 Strontium oxide & Vanadium(V) oxide, 84.9:8.4:4.6:2.1 w/w% ______________________________________________________________________________________________ General Advice If symptoms persist, call a physician. Eye Contact Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention. Skin Contact Wash off immediately with plenty of water for at least 15 minutes. If skin irritation persists, call a physician. Inhalation Remove to fresh air. If not breathing, give artificial respiration. Get medical attention if symptoms occur. Ingestion Clean mouth with water and drink afterwards plenty of water. Get medical attention if symptoms occur. Most important symptoms and Causes eye burns. Causes severe eye damage. effects Notes to Physician Treat symptomatically 5. Fire-fighting measures Unsuitable Extinguishing Media No information available Flash Point No information available Method - No information available Autoignition Temperature Not applicable Explosion Limits Upper No data available Lower No data available Sensitivity to Mechanical Impact No information available Sensitivity to Static Discharge No information available Specific Hazards Arising from the Chemical Keep product and empty container away from heat and sources of ignition. Hazardous Combustion Products Oxides of boron. Lithium oxide. Hydrogen fluoride. Strontium oxide. Vanadium oxides. Protective Equipment and Precautions for Firefighters As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear. NFPA Health Flammability Instability Physical hazards 4 0 0 N/A 6. Accidental release measures Personal Precautions Ensure adequate ventilation. Use personal protective equipment as required. Avoid dust formation. Environmental Precautions Should not be released into the environment. See Section 12 for additional Ecological Information. Do not allow material to contaminate ground water system. Do not flush into surface water or sanitary sewer system. Methods for Containment and Clean Sweep up and shovel into suitable containers for disposal. Keep in suitable, closed Up containers for disposal. ______________________________________________________________________________________________ Page 3 / 8 Spectroflux 135, Lithium tetraborate, Lithium fluoride, Revision Date 29-Feb-2020 Strontium oxide & Vanadium(V) oxide, 84.9:8.4:4.6:2.1 w/w% ______________________________________________________________________________________________ 7. Handling and storage Handling Wear personal protective equipment/face protection. Ensure adequate ventilation. Do not get in eyes, on skin, or on clothing. Avoid ingestion and inhalation. Avoid dust formation. Storage Keep containers tightly closed in a dry, cool and well-ventilated place. 8. Exposure controls / personal protection Exposure Guidelines Component ACGIH TLV OSHA PEL NIOSH IDLH Mexico OEL (TWA) Boron lithium oxide TWA: 2 mg/m3 (B4Li2O7) STEL: 6 mg/m3 Lithium fluoride TWA: 2.5 mg/m3 (Vacated) TWA: 2.5 mg/m3 IDLH: 250 mg/m3 TWA: 2.5 mg/m3 TWA: 2.5 mg/m3 Vanadium pentoxide TWA: 0.05 mg/m3 IDLH: 35 mg/m3 TWA: 0.05 mg/m3 Ceiling: 0.05 mg/m3 Legend ACGIH - American Conference of Governmental Industrial Hygienists OSHA - Occupational Safety and Health Administration NIOSH IDLH: NIOSH - National Institute for Occupational Safety and Health Engineering Measures Ensure that eyewash stations and safety showers are close to the workstation location. Personal Protective Equipment Eye/face Protection Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166. Skin and body protection Wear appropriate protective gloves and clothing to prevent skin exposure. Respiratory Protection Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Hygiene Measures Handle in accordance with good industrial hygiene and safety practice. 9. Physical and chemical properties Physical State Powder Solid Appearance White to off-white Odor No information available Odor Threshold No information available pH Not applicable Melting Point/Range No data available Boiling Point/Range No information available Flash Point No information available Evaporation Rate Not applicable Flammability (solid,gas) No information available Flammability or explosive limits Upper No data available Lower No data available Vapor Pressure No information available Vapor Density Not applicable Specific Gravity No information available ______________________________________________________________________________________________ Page 4 / 8 Spectroflux 135, Lithium tetraborate, Lithium fluoride, Revision Date 29-Feb-2020 Strontium oxide & Vanadium(V) oxide, 84.9:8.4:4.6:2.1 w/w% ______________________________________________________________________________________________ Solubility No information available Partition coefficient; n-octanol/water No data available Autoignition Temperature Not applicable Decomposition Temperature No information available Viscosity Not applicable 10. Stability and reactivity Reactive Hazard Yes Stability Stable under normal conditions. Conditions to Avoid Incompatible products. Incompatible Materials Strong oxidizing agents, Acids Hazardous Decomposition Products Oxides of boron, Lithium oxide, Hydrogen fluoride, Strontium oxide, Vanadium oxides Hazardous Polymerization Hazardous polymerization does not occur. Hazardous Reactions None under normal processing. 11. Toxicological information Acute Toxicity Product Information Oral LD50 Category 4. ATE = 300 - 2000 mg/kg. Dermal LD50 Based on ATE data, the classification criteria are not met. ATE > 2000 mg/kg. Mist LC50 Based on ATE data, the classification criteria are not met. ATE > 5 mg/l. Component Information Component LD50 Oral LD50 Dermal LC50 Inhalation Lithium fluoride 143 mg/kg Not listed Not listed Vanadium pentoxide 474 mg/kg ( Rat, male ) LD50 = 50 mg/kg ( Rabbit
Recommended publications
  • Safety Data Sheet
    SAFETY DATA SHEET SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Name of the substance Lithium oxide (Li2O) Identification number 235-019-5 (EC number) Synonyms Lithium oxide (Li2O) * Dilithium oxide * LITHIUM OXIDE Document number 1LW Materion Code 1LW Issue date 30-September-2013 Version number 04 Revision date 11-January-2018 Supersedes date 14-July-2015 1.2. Relevant identified uses of the substance or mixture and uses advised against Identified uses Not available. Uses advised against None known. 1.3. Details of the supplier of the safety data sheet Supplier Company name Materion Advanced Chemicals Inc. Address 407 N. 13th Street 1316 W. St. Paul Avenue Milwaukee, WI 53233 United States Division Milwaukee Telephone 414.212.0257 e-mail [email protected] Contact person Noreen Atkinson 1.4. Emergency telephone number SECTION 2: Hazards identification 2.1. Classification of the substance or mixture The substance has been assessed and/or tested for its physical, health and environmental hazards and the following classification applies. Classification according to Regulation (EC) No 1272/2008 as amended Health hazards Skin corrosion/irritation Category 1B H314 - Causes severe skin burns and eye damage. Serious eye damage/eye irritation Category 1 Hazard summary Causes serious eye damage. 2.2. Label elements Label according to Regulation (EC) No. 1272/2008 as amended Contains: Lithium oxide Hazard pictograms None. Signal word None. Hazard statements H314 Causes severe skin burns and eye damage. Precautionary statements Prevention P280 Wear eye protection/face protection. Response P301 + P330 + P331 IF SWALLOWED: rinse mouth.
    [Show full text]
  • Uncertain Material Experiment Size in Industry
    '10.5045 JULY 9. 1966 NATURE 125 The problem of nucleation is considered by V. N. Fili­ and certainly no information, about the reliability of povich by discussing a very simple model of a mixture some of the experimental results, in a field in which of two particles. As he says, " ... success depends on the reproducibility is not to be taken for granted. Figs. extent to which the model reflects the real system. The 45, 56 and 81 provide typical examples of justifiable development of a detailed theory of crystallization of doubts concerning the data. The theoret.ical calculations complex glasses and melts directly depends on the state seem to be similarly fraught with difficulties, and it is no of the theory of liquid and glass structure, which is still surprise to find a note added in proof which, concerning far from perfection". the displacement energy Ta, says "It now appears that The editor of this volume, E. A. Porai-Koshits, has 60 e Vis a better value than 25 e V, and if this is accepted, made important contributions to the study of glasses by the number of displaced atoms given in this book should X-ray diffraction and his laboratory has for some years be reduced by the ratio 25: 60". now concentrated on the use of small-angle X-ray diffrac­ The author has achieved a very creditable performance tion, light scattering and electron microscopy to study the with his cast of eccentrics and has provided a valuable, development of immiscibility in simple glasses and the up-to-date story of his field.
    [Show full text]
  • The Ionic Conductivity in Lithium-Boron Oxide Materials and Its Relation to Structural, Electronic and Defect Properties: Insights from Theory
    Journal of Physics: Condensed Matter TOPICAL REVIEW Related content - Topical Review The ionic conductivity in lithium-boron oxide Paul Heitjans and Sylvio Indris - Double perovskites with ferromagnetism materials and its relation to structural, electronic above room temperature and defect properties: insights from theory D Serrate, J M De Teresa and M R Ibarra - How chemistry controls electron localization in 3d1 perovskites: a Wannier- To cite this article: Mazharul M Islam et al 2012 J. Phys.: Condens. Matter 24 203201 function study E Pavarini, A Yamasaki, J Nuss et al. Recent citations View the article online for updates and enhancements. - Some device implications of voltage controlled magnetic anisotropy in Co/Gd 2 O 3 thin films through REDOX chemistry Guanhua Hao et al - Lithium Diffusion Mechanisms in -LiMO2 (M = Al, Ga): A Combined Experimental and Theoretical Study Mazharul M. Islam et al - First-principles study of structural, electronic, energetic and optical properties of substitutional Cu defect in Li 2 B 4 O 7 scintillator C. Santos et al This content was downloaded from IP address 134.129.67.237 on 13/06/2018 at 22:54 IOP PUBLISHING JOURNAL OF PHYSICS: CONDENSED MATTER J. Phys.: Condens. Matter 24 (2012) 203201 (29pp) doi:10.1088/0953-8984/24/20/203201 TOPICAL REVIEW The ionic conductivity in lithium-boron oxide materials and its relation to structural, electronic and defect properties: insights from theory Mazharul M Islam1,2, Thomas Bredow1,2 and Paul Heitjans2,3 1 Mulliken Center for Theoretical Chemistry, Universitat¨
    [Show full text]
  • Chemical Names and CAS Numbers Final
    Chemical Abstract Chemical Formula Chemical Name Service (CAS) Number C3H8O 1‐propanol C4H7BrO2 2‐bromobutyric acid 80‐58‐0 GeH3COOH 2‐germaacetic acid C4H10 2‐methylpropane 75‐28‐5 C3H8O 2‐propanol 67‐63‐0 C6H10O3 4‐acetylbutyric acid 448671 C4H7BrO2 4‐bromobutyric acid 2623‐87‐2 CH3CHO acetaldehyde CH3CONH2 acetamide C8H9NO2 acetaminophen 103‐90‐2 − C2H3O2 acetate ion − CH3COO acetate ion C2H4O2 acetic acid 64‐19‐7 CH3COOH acetic acid (CH3)2CO acetone CH3COCl acetyl chloride C2H2 acetylene 74‐86‐2 HCCH acetylene C9H8O4 acetylsalicylic acid 50‐78‐2 H2C(CH)CN acrylonitrile C3H7NO2 Ala C3H7NO2 alanine 56‐41‐7 NaAlSi3O3 albite AlSb aluminium antimonide 25152‐52‐7 AlAs aluminium arsenide 22831‐42‐1 AlBO2 aluminium borate 61279‐70‐7 AlBO aluminium boron oxide 12041‐48‐4 AlBr3 aluminium bromide 7727‐15‐3 AlBr3•6H2O aluminium bromide hexahydrate 2149397 AlCl4Cs aluminium caesium tetrachloride 17992‐03‐9 AlCl3 aluminium chloride (anhydrous) 7446‐70‐0 AlCl3•6H2O aluminium chloride hexahydrate 7784‐13‐6 AlClO aluminium chloride oxide 13596‐11‐7 AlB2 aluminium diboride 12041‐50‐8 AlF2 aluminium difluoride 13569‐23‐8 AlF2O aluminium difluoride oxide 38344‐66‐0 AlB12 aluminium dodecaboride 12041‐54‐2 Al2F6 aluminium fluoride 17949‐86‐9 AlF3 aluminium fluoride 7784‐18‐1 Al(CHO2)3 aluminium formate 7360‐53‐4 1 of 75 Chemical Abstract Chemical Formula Chemical Name Service (CAS) Number Al(OH)3 aluminium hydroxide 21645‐51‐2 Al2I6 aluminium iodide 18898‐35‐6 AlI3 aluminium iodide 7784‐23‐8 AlBr aluminium monobromide 22359‐97‐3 AlCl aluminium monochloride
    [Show full text]
  • Writing Chemical Formulas Name Student Activity Class
    Writing Chemical Formulas Name Student Activity Class Open the TI-Nspire document Writing_Chemical_Formulas.tns. In this activity you will practice writing chemical formulas for ionic binary compounds. Move to page 1.2. 1. Review the directions for this part of the activity. You can close the directions box by selecting . In this part of the activity you will write a chemical formula for a given cation and anion pair. Answer questions 1 – 4 here on the activity sheet. Tech Tip: To access the Directions again, select b or Document Tools ( ) > Writing Chemical Formulas > Directions. Tech Tip: To access the Directions again, select > Directions. Q1. Using the Periodic table, determine the valence of Li and F and record it in the table on the next page in the corresponding boxes. Explain your answer. Q2. What are ionic charges of the given cation and anion, Li and F? Why? Q3. What is the simplest ratio of positive and negative ions that is needed to produce a neutral compound? ©2014 Texas Instruments Incorporated 1 education.ti.com Writing Chemical Formulas Name Student Activity Class Q4. Determine the chemical formula for the Li and F compound. Check your answer by typing the formula in the ChemBox on page 1.2. Then write correct formula in the corresponding box in the table below. Anions - F Cl Br O S N P Cations + Li Na K Mg Ca Sr Al 2. Click the up or down arrows to select different cation and anion combinations. Answer questions 5 – 7 here on the activity sheet. Q5. Determine the valence of the cation and anion and record them in the table above in the corresponding boxes.
    [Show full text]
  • Doping Effects in Nanostructured Cadmium Tungstate Scintillation Films
    ARTICLE IN PRESS Journal of Luminescence 121 (2006) 527–534 www.elsevier.com/locate/jlumin Doping effects in nanostructured cadmium tungstate scintillation films Huamei Shanga, Ying Wanga, Brian Milbrathb, Mary Blissb, Guozhong Caoa,Ã aDepartment of Materials Science and Engineering, University of Washington, 302M Roberts Hall, Seattle, WA 98195-2120, USA bPacific Northwest National Laboratory, Richland, WA 99352, USA Received 8 August 2005; received in revised form 28 November 2005; accepted 20 December 2005 Available online 24 January 2006 Abstract This paper reports experimental study on the development of cadmium tungstate scintillator material in the form of nanocrystal films through controlled sol–gel processing and pre-designed doping. We chose cadmium tungstate as a base material for doping and nanostructure development due to its excellent inherent photoluminescence (PL) property, and chemical and thermal stability including non-hydroscopicity. Experimental results revealed that doping with Li+, B3+ and Bi3+ resulted in appreciably reduced grain size and increased density leading to enhanced optical transmittance. Further analyses indicated that PL output changed significantly with the introduction of dopants. The relationships between doping, microstructure, and PL were discussed. r 2006 Elsevier B.V. All rights reserved. PACS: 14.20.Dh Keywords: Cadmium tungstate; Scintillator; Sol–gel processing; Doping; Photoluminescence 1. Introduction widely used in spectrometry and radiometry of radionuclides in extra-low activities, especially Among scintillating materials, cadmium tung- used for computer tomography (CT) [1]. Because 3 state (CdWO4, CWO) is a high-density (7.9 g/cm ), of its capability of radiation capture, CWO has high-Z (atomic number) scintillator with a rela- also been actively studied for applications in X- tively large light yield.
    [Show full text]
  • Template for Electronic Submission of Organic Letters
    doi:10.20396/revpibic.v0i0.id Manganese residue treatment as a new approach to manganese dioxide production. Rafael F. Cunha*, Lorrane C. C. B. Oliveira, Leticia F. Cremasco, Gustavo Doubek. Abstract Lithium-air batteries performance faces a challenge on the design and development of a functional cathode. Manganese dioxide is a promising material for the air cathode, due to its low cost and ability to catalyse oxygen reactions. In its preparation residues are generated that need to be treated before discard. The present study aims to prepare the manganese dioxide through a precipitation/annealing method, using as raw-material manganese based waste from electrodeposition baths utilized in a previous study, in order to synthesize novel MnOx based electrodes. Key words: Manganese dioxide, Materials engineering, Lithium-air batteries. Introduction stainless-steel net surface and let to dry in oven. The Electrification of automotive fleet, aligned with the prepared electrode was cycled in lithium-oxygen battery, development of sustainable sources of primary energy, and the result is presented on Image 1. rises as a solution to reduce worldwide carbon dioxide emissions without reducing vehicle usage. However, state-of-the-art lithium-ion technology cannot provide a range high enough to fully replace internal combustion engines for batteries. Lithium-air batteries have a theoretical gravimetric energy (mWh/gactive material) 5 to 8 times higher than that of conventional lithium-ion. The system is based on the reaction between lithium and oxygen to produce a lithium oxide. The technology, however, faces some challenges, among which are large overpotential and low reversibility. In order to overcome these issues, different materials have been studied as catalysts for charge and discharge reactions¹.
    [Show full text]
  • Ionic Compounds Pogil
    Agenda Dec 3, 2019 Quick Questions(Ions Pogil - Big Ideas) Quick review Octet Rule and Ionic bonding notes Naming Ionic Compounds Pogil Start Work on Study Guide for Final 1. Write out the correct statement only. QQs a) Metals make negative anions and nonmetals make positive cations. b) Metals make positive cations and nonmetals make negative anions. c) Metals make negative cations and nonmetals make positive anions. d) Metals make positive anions and nonmetals make negative cations. 2. What is the charge on an ion with 21 protons, 25 neutrons and 18 electrons? a) 4+ b) 3+ c) 4- d) 4+ QQs 1. Write out the correct statement only. b) Metals make positive cations and nonmetals make negative anions. 2. What is the charge on an ion with 21 protons, 25 neutrons and 18 electrons? 21protons (21+) 18 electrons (18-) 21 - 18 = 3 QQs 1. Write out the correct statement only. b) Metals make positive cations and nonmetals make negative anions. 2. What is the charge on an ion with 21 protons, 25 neutrons and 18 electrons? b) 3+ 21protons (21+) 18 electrons (18-) 21 - 18 = 3 The Octet Rule Atoms tend to gain, lose or share electrons in order to acquire a full set of eight valence electrons. Electron configurations like those of the Noble gases with filled s and p orbitals of the same energy level are unusually stable. (Note that Helium has only 2 valence electrons, but that is because the 1st energy level can only accommodate 2 electrons in its 1s orbital.) Octet rule is useful for determining the type of ions that elements are likely to form.
    [Show full text]
  • Phase Equilibria of Stored Chemical Energy Reactants
    Phase Equilibria of Stored Chemical Energy Reactants L P. Cook E. R. Plante R. S. Roth J. W. Hastie U.S. DEPARTMENT OF COMMERCE National Bureau of Standards Center for Materials Science Gaithersburg, MD 20899 September 1984 Prepared for *H^rtment of the Navy QC ice of Naval Research ington, VA 22217 100 ,[)5lp NO- KATIOHAt bureau OF STANDARDS library NBSIR 84-2940 PHASE EQUILIBRIA OF STORED CHEMICAL Ocfoo ENERGY REACTANTS po. L. P. Cook E. R. Plante R. S. Roth J. W. Hastie U.S. DEPARTMENT OF COMMERCE National Bureau of Standards Center for Materials Science Gaithersburg, MD 20899 September 1984 Prepared for Department of the Navy Office of Naval Research Arlington, VA 22217 U.S. DEPARTMENT OF COMMERCE, Malcolm Baldrige, Secretary NATIONAL BUREAU OF STANDARDS, Ernest Ambler, Director 7 Phase Equilibria of Stored Chemical Energy Reactants Annual Report For the Period May 25, 1983 “ May 25, 198^1 L. P. Cook, E. R. Plante, R. S. Roth and J. W. Hastie Inorganic Materials Division Center for Materials Science National Bureau of Standards Gaithersburg, Md 20899 July 25, 1984 Prepared for the Department of the Navy Office of Naval Research Arlington, VA 22217 Under Contract No. N0001 4-83-F-01 1 APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED REPRODUCTION IN WHOLE OR IN PART IS PERMITTED FOR ANY PURPOSE OF THE U. S. GOVERNMENT J • f ; i’ f I® m-:c * 'V >.f:r^ ' '*f^ f!' ‘.<t5 f U '%K ,>• '''^?fifjj ’/jjjii M ; Jft W-ml 4" ^' i>; 4^'' - -mik 3«r M pn lai * 'll ,. ;' ® ... \ V.. • ’^^ •*'?v/>f *L, b'# Phase Equilibria of Stored Chemical Energy Reactants Table of Contents Abstract 1 I.
    [Show full text]
  • Binary Ionic Compounds Name: ______Per: ______
    Binary Ionic Compounds Name: ___________________ Per: ______ Directions: First quickly scan the worksheet and circle any metals (as a symbol or as a name) that is a transition metal. Then either give the same or chemical formula as necessary for each problem below. Remember that transition metals can have multiple oxidation states, so you are required to indicate the appropriate oxidation state in parenthesis when naming them. You must use the subscript and oxidation state of the anion to help determine the oxidation state of the transition metal. 1. LiF _____________________ 2. lithium chloride ____________ 3. Li2O _____________________ 4. lithium nitride ____________ 5. Li3P _____________________ 6. beryllium fluoride ____________ 7. BeO _____________________ 8. beryllium sulfide ____________ 9. BF3 _____________________ 10. boron chloride ____________ 11. BBr3 _____________________ 12. boron oxide ____________ 13. BN _____________________ 14. sodium fluoride ____________ 15. CuF _____________________ 16. copper (II) chloride ____________ 17. Cu2O _____________________ 18. copper (II) oxide ____________ 19. Cu3N _____________________ 20. copper (II) nitride ____________ 21. Na2O _____________________ 22. sodium nitride ____________ 23. PbF2 _____________________ 24. lead (IV) fluoride ____________ 25. PbS _____________________ 26. lead (IV) sulfide ____________ 27. Pb3N4 _____________________ 28. lead (IV) oxide ____________ 29. FeF3 _____________________ 30. iron (II) bromide ____________ 31. Fe2O3 _____________________ 32. chromium (VI) phosphide ____________ 33. FeP _____________________ 34. aluminum fluoride ____________ 35. AlI3 _____________________ 36. aluminum oxide ____________ 37. Mn2O7 _____________________ 38. manganese (IV) bromide ____________ 39. SnSe _____________________ 40. tin (IV) oxide ____________ Jasmann 08 Binary Ionic Compounds ANSWER KEY Directions: First quickly scan the worksheet and circle any metals (as a symbol or as a name) that is a transition metal.
    [Show full text]
  • Thermal Stability of Oxidized Ultrathin Li Films on TZM for Plasma Facing
    Journal of Nuclear Materials 543 (2021) 152587 Contents lists available at ScienceDirect Journal of Nuclear Materials journal homepage: www.elsevier.com/locate/jnucmat Thermal stability of oxidized ultrathin Li films on TZM for plasma facing components ∗ O. Fasoranti a, E.T. Ostrowski b, B.E. Koel b, a Department of Chemistry, Princeton University NJ, 08540 USA b Department of Chemical and Biological Engineering, Princeton University NJ, 08540 USA a r t i c l e i n f o a b s t r a c t Article history: For improved understanding of the behavior of Li plasma facing components (PFCs) in the presence of Received 14 July 2020 oxygen impurities, we report on the thermal stability of ultrathin (up to 1.0 nm) LiO x films on a titanium- Revised 22 September 2020 zirconium-molybdenum (TZM) alloy substrate over the temperature range of 310–1400 K. LiO x films were Accepted 4 October 2020 prepared by either post-oxidation of Li films or Li films deposited on an oxygen-precovered TZM surface. Available online 9 October 2020 Thermal stability of these films was studied using a combination of temperature programmed desorption Keywords: (TPD), X-ray photoelectron spectroscopy (XPS), and low-energy ion scattering (LEIS). For post-oxidized Li Lithium films, TPD showed that no Li desorption occurred until temperatures above 620 K, and then Li desorbed molybdenum from the surface via at least three desorption peaks. The O 1s XPS spectra on the post-oxidized films TZM at 310 K indicate the formation of lithium oxide (Li 2 O) and peroxide/hydroxide (Li 2 O 2 /LiOH).
    [Show full text]
  • Prospects for Thermal Energy Storage
    AG-81 PROSPECTS FOR THERMAL ENERGY STORAGE MANFRED ALTMAN Director, Institute for Direct Energy Conversion and Professor of Mechanical Engineering, University of Pennsylvania This paper is concerned with the problem of developing a method of storing thermal energy by the utilization of the heat offusion of suitable compounds. The first part of the paper discusses the incentives for the development of this type of energy storage. The second part deals with the problem of synthesising suitable materials. The third part discusses the problem of obtaining the needed heat trans- fer properties. The main conclusions of this work are as follows: I. A good case can he made for space power systems utilizing thermal energy storage. 2. This is predicated on technical developments which appear probable, but which have not yet been accomplished. 3. A great deal of work remains to be done in two major research areas. One, the determination of phase diagrams of promising eutectic mixtures, and two, the experimental and theoretical determination of heat transfer properties. 4. A carefully planned systematic approach is needed to obtain the information necessary for systems comparisons. On considère Is probleme du developpement d'une méthode de stokage d'énergie thermique en se servant de la chaleur de fusion de mélanges appropriés. Dans la premiere partie, on discute l'intérit du développement d'un tel stokage. Darts la seconds, la synthJse des matériaux néccessaires est discutée. La troisiJme partie a trait aux prop ritétés de transfert de chaleur requises. En conclusion il est montré que: 1. Le stokage d'énergie thermique est une methods interessante pour les systèmes de propulsion spaciaux.
    [Show full text]