DOCSLIB.ORG

Crystalite®Lapidary & Glass Products

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Crystalite®Lapidary & Glass Products CRYSTALITE CORPORATION CRYSTALITE® LAPIDARY & GLASS PRODUCTS An Abrasive Technology Company WARNING: Cancer DIAMOND WHEELS www.PWarnings.ca.gov Crystalring® This efficient, lightweight wheel features a uniform, continuous diamond coating. No voids exist in the seamless steel rim of this electroplated wheel. Crystalring® wheels are designed to run on conventional cabochon units operating at 1725 rpm. The 1” arbor hole is bushed to 3/4”, 5/8”, and 1/2”. WARNING Mesh : Cancer4” x 1-1/2” 6” x 1” 6” x 1-1/2” 8” x 1-1/2” www.PWarnings.ca.gov 60 C5321290 C5322010 C5323210 80 C5322030 C5323230 100 C5320150 C5321310 C5322050 C5323250 180 C5321330 C5322070 C5323270 220 C5320170 C5321350 C5322090 C5323290 360 C5320190 C5321370 C5322110 C5323310 600 C5320210 C5321390 C5322130 C5323330 1200 C5320230 Turbine Wheel® This diamond wheel has a unique, sawtoothed profile. As the crests wear, sharp fresh diamond is exposed, making it one of the fastest roughing wheels ever built Diamondback™ for preforming agate, jasper, and other hard stones. This aggressive diamond wheel is uniquely designed with an The 1” arbor hole is bushed to 3/4”, 5/8”, and 1/2”. interrupted cutting surface which delivers a definite metallic uplift. Recommended operating speed is 1500 to 2000 rpm. It contains one-third more diamond than our regular Crystalring® wheel, producing a longer lasting wheel with a higher cutting rate. WARNINGMesh : 6”Cancer x 1-1/2” 8” x 1-1/2” The 360 mesh wheel is capable of roughing stones while yielding a www.PWarnings.ca.gov gentle finish. The 1” arbor hole is bushed to 3/4”, 5/8”, and 1/2”. 40 C5325950 C5326950 100 C5326010 C5327010 180 C5326030 C5327030 Cancer WARNINGMesh :6” x 1-1/2” 8” x 1-1/2” 260 C5326050 C5327050 www.PWarnings.ca.gov 100 C5328210 C5328310 180 C5328230 C5328330 360 C5328270 C5328370 Helpful Hints Recommended RPM’s 1. Allow wheels to spin dry after use. Wheel Diameter 4” 6” 8” 2. Use Crystalcut™ additive in water to inhibit rust. Recommended RPM 2500 1725 1400 1 WARNING: Cancer www.PWarnings.ca.gov DIAMOND WHEELS Spherical Miracle™ Crystalcut™ RADIUSED WHEELS Recommended wherever diamond wheels are used with Now you can grind a spherical depression in your workpiece. The water. Crystalcut™ water additive and rust inhibitor should radius design produces more cutting power than conventional flat be used with diamond wheels, saw blades and discs. Mix 1 wheels, delivering a double bite. This wheel promotes high visibility ounce of powder with each gallon of water. of the point of contact with the stone, allowing you precise control of (Not available for air shipment) the cutting outline. The Spherical Miracle™ wheel will also remove punting marks. The 1” arbor hole is bushed to 3/4”, 5/8” and 1/2”. WARNINGSize : Cancer Stock No. • Excellent for lapidary and light glass work. www.P 1 oz.Warnings.ca.gov C5423310 1 lb. C5423330 WARNINGMesh :6” Cancer x 1-1/2” 8” x 1-1/2” 5 lb. C5423350 10 lb. C5423370 www.P100 Warnings.ca.gov C5329110 C5329330 360 C5329130 C5329370 600 C5329140 C5329390 Crystalmet™ SINTERED METAL BOND WHEELS These sintered metal bond wheels are made with our proprietary bond formulation. Manufactured for the lapidary industry, Crystalmet™ wheels will provide an excellent finish, long life and an aggressive cut- ting action. They are ideal for those who want high volume production and long life from their wheels. ® Note: Use the entire face of the wheel to avoid grooving. If slow cutting Crystalite Dressing Sticks occurs, dress the face of the wheel with our dressing stick to restore the Sharpen Crystalite® metal bond diamond discs, cutting action. Use with Crystalcut™ rust inhibitor. Additional mesh wheels, diamond saw blades, knives and many sizes and wheel dimensions are available. other tools with these sticks. Item Stock No. 6 x 1 x 1 8 x 1 x 1 WARNING: Cancer Mesh Application 1/8 depth 1/8 depth Fine (600 & finer mesh) C5431010 www.PWarnings.ca.gov Coarse (360 & coarser mesh) C5431030 60 Very Coarse C5328510 C5328610 Stick Kit (Set of two) C5431100 120 Rough C5328530 C5328630 180 Preform C5328540 C5328640 325 Honing C5328550 C5328650 600 Sanding C5328560 C5328660 1200 Pre-Polish C5328570 C5328670 2 WARNING: Cancer DIAMOND SAW BLADES | DIAMOND DISCS www.PWarnings.ca.gov Primecut™ These diamond saw blades set a new standard for thin diamond blades. Manufactured with our own proprietary diamond plating process, these 100/120 mesh blades will cut faster, last longer and run truer than any other blade we offer. Primecut™ saw blades feature: • Continuous diamond plating on cutting edge The Standard™ • 3/32” return of diamond down the sides These discs are used by commercial cutters worldwide and are excellent • Serrated cutting edge surface for faceting. The aluminum backs are ground flat and parallel to exacting • Improved diamond coverage and plating standards and are made with 100% diamond and bonded with a hard Additional sizes available. electroplated nickel. The Standard™ discs are also available with a 1/4” - 20 thread screwback mount, allowing you to utilize the full face of WARNING: Cancer Center Hole the disc. This uninterrupted surface will allow you to handle larger work www.PWarnings.ca.gov pieces. Other diameters, mesh sizes and arbor holes are available. Diameter Rim 1/2” 5/8” 4” .025 C5555030 C5555040 1/4” - 20 6” .025 C5555110 C5555120 Screwback Mount 6” .033 C5555130 C5555140 1/2” Arbor Hole (No Arbor Hole) 8” .025 C5555150 C5555160 8” .035 C5555170 C5555180 WARNING Mesh : Cancer 6” 8” 6” 8” www.PWarnings.ca.gov 10” .042 C5555190 C5555200 100 C5301210 C5301410 C5301610 C5301710 180 C5301230 C5301430 260 C5301250 C5301450 C5301630 C5301730 360 C5301270 C5301470 600 C5301290 C5301490 C5301650 C5301750 Diamond Wire Saw 1200 C5301310 C5301510 The diamond wire hand saw has many lapidary uses. 3000 C5301350 C5301550 A complex shape has been sawed in the Brazilian agate slab shown above. WARNING : Cancer Item Stock No. www.P BarbedWarnings.ca.gov wire saw - 180 mesh, 5-1/8” x .032 C5202310 Barbed wire saw & frame kit C5202400 Round wire saw - 180 mesh, 5-1/8” x .027 C5202510 Round wire saw & frame kit C5202600 3 WARNING: Cancer www.PWarnings.ca.gov DIAMOND DISCS Solid Steel Discs Crystalmet™ Disc Protector™ They are absolutely flat and parallel to meet the Each protector will hold one 6” or 8” disc. SINTERED METAL BOND DISCS This protective case will help insure a most exacting faceting requirements. Additionally, These sintered metal bond diamond discs are made with our contamination free environment for your these discs have a corrosion resistant copper proprietary bond formulation. Manufactured for the lapidary expensive faceting tools. These high impact undercoating. A 1/2” arbor hole is standard industry, Crystalmet™ discs will provide an excellent finish, polystyrene containers are stackable with (specify other). Additional sizes are available. long life and an aggressive cutting action. They are ideal for interlocking grooves for space saving storage. those who want high volume production and long life from WARNING: Cancer Mesh 6” 8” their discs. A 1/2” arbor hole is standard (specify other). Must specify for 1/2” arbor hole or www.PWarnings.ca.gov 60 C5302090 C5302290 screwback style mounting. 100 C5302110 C5302310 WARNING Mesh : ApplicationCancer 6 x 3/16 x 1/2 8 x 3/16 x 1/2 www.PWarnings.ca.gov 180 C5302130 C5302330 120 Roughing C5303230 C5303330 Item Stock No. 260 C5302150 C5302350 600 Smoothing C5303260 C5303360 Arbor Hole style C5243320 360 C5302170 C5302370 1200 Sanding or C5303270 C5303370 Screwback style C5243310 600 C5302190 C5302390 Pre-polish for 1200 C5302210 C5302410 some stones 3000 C5302250 C5302450 4 WARNING: Cancer DIAMOND DISCS www.PWarnings.ca.gov Channel Disc™ This disc has a uniquely shaped working surface of randomly interspaced islands. The resulting channels flush away debris and prevent the stone from pulling down excessively to the lap. It is superb for rough cutting facets and grinding cabochon backs. Note: These discs will cut faster and are coarser than The Standard™ discs. 180 mesh is an excellent cabochon preformer - 360 mesh is superb for facet roughing -1200 mesh is excellent for facet finishing. 1/2” Arbor hole. WARNINGMesh : Cancer 6” 8” www.P 180Warnings.ca.gov C5300110 C5300310 260 C5300130 C5300330 360 C5300150 C5300350 600 C5300170 C5300370 Dot Disc™ 1200 C5300190 C5300390 Now you can handle large work pieces with ease. These dot pattern discs feature aggressive, fast cutting action for rough cabbing and preforming large faceted stones. They are ideal for cutting large flat areas where hydroplaning and grinding force are factors. These discs come with or without an arbor hole. For discs with an arbor, a 1/2” center hole is standard (specify other). Discs without a center hole provide you with a larger working area for glass and stone, allowing Ripple Disc™ you to utilize the full face of the disc. Other diameters, mesh sizes and arbor holes are available. The fast cutting 100 mesh disc cuts like a 40 mesh and the 180 mesh disc cuts like a 60 mesh. It is excellent for rough cabbing and preforming large faceted stones. As the tips of the ripple 1/4” - 20 forms wear, fresh diamond is exposed, permitting the disc to Screwback Mount 1/2” Arbor Hole (No Arbor Hole) remain sharp throughout its long life. This disc will cut agate with ease. 1/2” Arbor hole. WARNING Mesh : Cancer 6” 8” 6” 8” www.PWarnings.ca.gov 60 C5304000 C5304060 C5304120 C5304180 WARNINGMesh : Cancer 6” 8” 100 C5304010 C5304070 C5304130 C5304190 www.P 100Warnings.ca.gov C5300470 C5300490
Load more

Recommended publications
  • Troubleshooting Decorative Electroplating Installations, Part 5
    Troubleshooting Decorative Electroplating Installations, Part 5: Plating Problems Caused Article By Heat & Bath Temperature Fluctuations by N.V. Mandich, CEF, AESF Fellow Technical Technical In previous parts of this series, emphasis was given The fast-machining steels must then be carburized to troubleshooting of the sequences for pre-plating or case-hardened to obtain a surface with the hardness and electroplating over metals, Parts 1 and 2;1 required to support the top chromium electroplate. the causes, symptoms and troubleshooting for Case hardening is the generic term covering several pores, pits, stains, blistering and “spotting-out” processes applicable to steel or ferrous alloys. It changes phenomena, Part 3;2 and troubleshooting plating on the surface composition of the top layer, or case, by plastic systems, Part 4.3 Here in Part 5, causes and adsorption of carbon, nitrogen or a mixture of the two. some typical examples of problems that occur in By diffusion, a concentration gradient is created. The electroplating as a result of a) thermal, mechanical heat-treatments and the composition of the steel are surface treatments, b) the metallurgy of the part to additional variables that should be addressed and taken be plated or c) effects of plating bath temperature into account in the electroplating procedure. on plating variables and quality of the deposits When discussing the effect of heat-treatment on are discussed. subsequent electroplating processes it is necessary to zero in on the type of heat-treatment involved. We Nearly every plater has at one time or another had the can defi ne the heat-treatment process as changing the experience of trying to plate parts that simply would characteristics of the parts by heating above a certain not plate.
    [Show full text]
  • UDDEHOLM STAVAX® ESR © UDDEHOLMS AB No Part of This Publication May Be Reproduced Or Transmitted for Commercial Purposes Without Permission of the Copyright Holder
    UDDEHOLM STAVAX® ESR © UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties of the products described or a warranty for fitness for a particular purpose. Classified according to EU Directive 1999/45/EC For further information see our “Material Safety Data Sheets”. Edition 11, 05.2013 The latest revised edition of this brochure is the English version, SS-EN ISO 9001 which is always published on our web site www.uddeholm.com SS-EN ISO 14001 UDDEHOLM STAVAX ESR UDDEHOLM STAVAX ESR Uddeholm Stavax ESR is a premium stainless mould steel for small and medium inserts and cores. Uddeholm Stavax ESR combines corrosion and wear resistance with excellent polishability, good machinability and stability in hardening. Mould maintenance requirement is reduced by assuring that core and cavity surfaces retain their original finish over extended operating periods. When compared with non stainless mould steel, Uddeholm Stavax ESR offers lower production costs by maintaining rust free cooling channels, assuring consistent cooling and cycle time. This classic stainless tool steel is the right choice when rust in production is unacceptable and where requirements for good hygiene are high, as within the medical industry, optical industry and for other high quality transparent parts. Uddeholm Stavax ESR is a part of the Uddeholm Stainless Concept 3 UDDEHOLM STAVAX ESR General Applications Uddeholm Stavax ESR is a premium grade Uddeholm Stavax ESR is recommended for all stainless tool steel with the following proper- types of moulding tools and its special proper- ties: ties make it particularly suitable for moulds •good corrosion resistance with the following demands: •excellent polishability • Corrosion/staining resistance, i.e.
    [Show full text]
  • Investigating the Effect of Post Processing Procedures On
    Investigating the Effect of Post Processing Procedures on Corrosion Resistance of Additively Manufactured 316L Stainless Steel Science and Technology Program Research and Development Office Final Report No. ST-2020-20035 Technical Memorandum No. 8540-2020-20035 50 microns U.S. Department of the Interior September 2020 Form Approved REPORT DOCUMENTATION PAGE OMB No. 0704-0188 The public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 2. REPORT TYPE 3. DATES COVERED (From - To) 09-30-2020 Research FY20 – FY20 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER Investigating the Effect of Post Processing Procedures on Corrosion 20XR0680A1-RY15412020PE20035/X0035 Resistance of Additively Manufactured 316L Stainless Steel 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 1541 (S&T) 6. AUTHOR(S) 5d. PROJECT NUMBER Stephanie Prochaska, M.S., Materials Engineer ST-2020-20035 8540-2020-45 5e.
    [Show full text]
  • An Introduction to Buffing and Polishing
    AN INTRODUCTION TO BUFFING AND POLISHING 7696 Route 31, Lyons NY 14489 http://www.caswellplating.com (315) 946-1213 Page 1 To Order Call: 315-946-1213 AN INTRODUCTION TO BUFFING & POLISHING Buffing and polishing using wheels and ‘compounds’ is somewhat like using wet and dry sanding paper, only much faster. Instead of using ‘elbow grease’ you will be using the power and speed of an electric motor. The edge, or face, of the wheel is the ‘sanding block’, which carries a thin layer of compound’ which is the sandpaper. Varying types of wheel are available, and the different grades of com- pound are scaled similar to sandpaper. The compounds are made from a wax substance which has the different abrasive powders added to it. When this hard block is applied to the edge of a spinning buffing wheel, the heat from the friction melts the wax, and both wax and abrasive are applied in a thin slick to the face of the wheel. The objective of buffing and polishing is to make a rough surface into a smooth one and, of course, each work piece will be in a different condition, so will need different procedures. Imagine the surface magnified thousands of times, it will look like jag- ged mountains and valleys. By repeated abrasion, you are going to wear down those mountains until they are old, soft, rolling hills! Then they will not dissipate the light, but reflect it. It is the reflection that makes the buffed part appear shiny. TRICKS OF THE TRADE Repairing small dents. Sand the inside of the part with emery paper.
    [Show full text]
  • The Dynisco Extrusion Processors Handbook 2Nd Edition
    The Dynisco Extrusion Processors Handbook 2nd edition Written by: John Goff and Tony Whelan Edited by: Don DeLaney Acknowledgements We would like to thank the following people for their contributions to this latest edition of the DYNISCO Extrusion Processors Handbook. First of all, we would like to thank John Goff and Tony Whelan who have contributed new material that has been included in this new addition of their original book. In addition, we would like to thank John Herrmann, Jim Reilly, and Joan DeCoste of the DYNISCO Companies and Christine Ronaghan and Gabor Nagy of Davis-Standard for their assistance in editing and publication. For the fig- ures included in this edition, we would like to acknowledge the contributions of Davis- Standard, Inc., Krupp Werner and Pfleiderer, Inc., The DYNISCO Companies, Dr. Harold Giles and Eileen Reilly. CONTENTS SECTION 1: INTRODUCTION TO EXTRUSION Single-Screw Extrusion . .1 Twin-Screw Extrusion . .3 Extrusion Processes . .6 Safety . .11 SECTION 2: MATERIALS AND THEIR FLOW PROPERTIES Polymers and Plastics . .15 Thermoplastic Materials . .19 Viscosity and Viscosity Terms . .25 Flow Properties Measurement . .28 Elastic Effects in Polymer Melts . .30 Die Swell . .30 Melt Fracture . .32 Sharkskin . .34 Frozen-In Orientation . .35 Draw Down . .36 SECTION 3: TESTING Testing and Standards . .37 Material Inspection . .40 Density and Dimensions . .42 Tensile Strength . .44 Flexural Properties . .46 Impact Strength . .47 Hardness and Softness . .48 Thermal Properties . .49 Flammability Testing . .57 Melt Flow Rate . .59 Melt Viscosity . .62 Measurement of Elastic Effects . .64 Chemical Resistance . .66 Electrical Properties . .66 Optical Properties . .68 Material Identification . .70 SECTION 4: THE SCREW AND BARREL SYSTEM Materials Handling .
    [Show full text]
  • Electrode Polishing and Care
    LCEC and EC Accessories January 2001 A-1302 ELECTRODE POLISHING AND CARE Cross-Flow Cell Package UniJet Cell Package C3 Voltammetry Cell Stand Rotating Disk Electrode Low Current Module Calomel Reference Electrode Bioanalytical www.bioanalytical.com Systems, Inc 2701 Kent Avenue West Lafayette Indiana 47906 Thank you for your recent purchase from BAS. This manual includes instructions for several different products, and should be used as a supplement to various BAS instrument manuals. Due to continuing development of our line, some products may be slightly different in appearance from the drawings depicted here. These changes should not affect performance or the relevant use and maintenance instructions. Check the inserts that may be provided with individual electrodes for additional notes or revisions. Working electrodes are warranted for 60 days from date of shipment. Reference electrodes are considered consumable items and are not covered by a timed warranty period. We warrant only that they are viable as shipped. Their lifetime after purchase will depend solely on usage and storage conditions. Copyright May 1998, January 2001 Bioanalytical Systems, Inc. 2701 Kent Avenue West Lafayette, IN 47906 USA www.bioanalytical.com ALL RIGHTS RESERVED UniJet, UniStand, and SepStik are trademarks of Bioanalytical Systems, Inc. Vycor is a registered trademark of Corning Glass. Kel-F is a registered trademark of 3M Corporation. Table of Contents Table of Contents Section 1. Thin-Layer Cells........................................................................................
    [Show full text]
  • Metallographic Preparation of Stainless Steel Application Notes
    Metallographic preparation of stainless steel Application Notes Corrosion resistant steels contain at least 11% chromium and are collectively known as “stainless steels“. Within this group of high alloy steels four categories can be identified: ferritic, martensitic, austenitic, and austenitic-ferritic (duplex) stainless steels. These categories de- scribe the alloy’s microstructure at room temperature, which is largely influenced by the alloy composition. The main characteristic of stainless steels is their corrosion resistance. This prop- High performance stainless steel parts for the erty can be enhanced by the addition of aircraft industry specific alloying elements, which have a further beneficial effect on other charac- chemical, medical and food industries, teristics such as toughness and oxidation in professional kitchens, architecture and resistance. even jewelry. For instance, niobium and titanium in- Metallography of stainless steels is an crease resistance against intergranular important part of the overall quality corrosion as they absorb the carbon to control of the production process. The form carbides; nitrogen increases strength main metallographic tests are grain size and sulphur increases machinability, measurement, identification of delta because it forms small manganese sul- ferrite and sigma phase and the evalu- phides which result in short machining ation and distribution of carbides. In chips. Due to their corrosion resistance addition, metallography is used in failure and superior surface finishes stainless analysis investigating corrosion/oxida- steels play a major part in the aircraft, tion mechanisms. Fig.1: Duplex steel etched electrolytically with 150x 40% aqueous sodium hydroxide solution, showing blue austenite and yellow ferrite Difficulties during metallographic preparation Solution: Grinding and polishing: Deformation and scratching in ferritic and austenitic stain- Thorough diamond polishing and final less steels.
    [Show full text]
  • Improvement of Punch and Die Life and Part Quality in Blanking of Miniature Parts
    Improvement of Punch and Die Life and Part Quality in Blanking of Miniature Parts DISSERTATION Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy in the Graduate School of The Ohio State University By Soumya Subramonian Graduate Program in Mechanical Engineering The Ohio State University 2013 Dissertation Committee: Dr.Taylan Altan, Advisor Dr.Blaine Lilly, Advisor Dr.Gary L.Kinzel Dr.Jerald Brevick Abstract Blanking or piercing is one of the most commonly used sheet metal manufacturing processes in the industry. Having a good understanding of the fundamentals and science behind this high deformation shearing process can help to improve the tool life and blanked edge quality in various ways. Finite Element Modeling of the blanking process along with experimental testing is used in this study to study the influence of various process parameters on punch and die life and blanked edge quality. In high volume blanking and blanking of high strength materials, improving the tool life can save not only tool material but also change over time which can take up to a few hours for every change over. The interaction between punch, stripper plate and sheet material is first studied experimentally since a fundamental understanding of the behavior of these components at different blanking speeds is very essential to design robust tooling for high speeds. A methodology is developed using the experimentally obtained blanking load and FEM of blanking to obtain flow stress data of the sheet material at high strains and strain rates. This flow stress data is used to investigate the effects of various process parameters on tool stress and blanked edge quality.
    [Show full text]
  • Chapter 2 the Preparation of Samples for Ore Microscopy
    CHAPTER 2 THE PREPARATION OF SAMPLES FOR ORE MICROSCOPY 2.1 INTRODUCTION Th e preparation of polished surfaces free from scratches, from thermal and mechanical modification of the sample surface, and from relief is essential forthe examination, identification, and textural interpretation of ore minerals using the reflected-light microscope. Adequate polished surfaces can be pre­ pared on many types of materials with relatively little effort using a wide variety of mechanical and manual procedures. However, ore samples often present problems because they may consist ofsoft, malleable sulfides or even nati ve metal s intimately intergrown with hard, and som etimes brittle, sili­ cates, carbonates, oxides, or other sulfides. Weathering may complicate the problem by removing cements and interstitial minerals and by leaving sam­ ples that are friable or porous. Delicate vug fillings also cau se problems with theiropen void spaces and poorly supported crystals.Alloys and ben eficiation products present their own difficulties because of the presence of admixed ph ases ofvariable properties and fine grain sizes. In this chapter, the general procedures ofsample selection and trimming, casting, grinding, and polish­ ing (and, in special cases, etching) required to prepare solid or particulate samples for examination with the ore microscope are discussed. The prepara­ tion ofthese polishedsections, and also polished and doubly polished thin sec­ tions, which are useful in the study of translucent or coexisting opaque and translucent specimens, is described. These are matters about which all stu­ dents of reflected-light microscopy should be aware, ideally through per­ sonal experience. lReliej is the un even surface of a section resulting from so ft ph ases being worn away mor e than hard ph ases during polish ing.
    [Show full text]
  • Welding ABSTRACT Units Are General Safety, Basic Metalworking Tools, Layout, Bench Metal Casting, Welding, Metal Finishing, Plan
    DOCUMENT RESUME ED 223 837 CE 034 374 TITLE lndustrial Arts Curriculum Guide in Basic Metals. Bulletin No. 1685. INSTITUTION Louisiana State Dept. of Education, Baton Rouge. Div. of Vocational Education. PUB DATE Sep 82 NOTE 127p.; For related documents, see CE 034 372-375. PUB TYPE Guides Classroom Use Guides (For Teachers) (052) EDRS PRICE MF01/PC06 Plus Postage. DESCRIPTORS Behavioral Objectives; *Course Content; Curriculum Guides; Equipment Utilization; Hand Tools; *Industrial Arts; Instructional Materials; Learning Activities; Machine Tools; Metal Industry; *Metals; *Metal Working; Planning; *Program Implementation; Safety; Secondary Education; Sheet Metal Wolk; *Trade and Industrial Education; Vocational Education; Welding IDENTIFIERS *Louisiana ABSTRACT This curriculum guide contains operational guidelines to help local-administrators, teacher educators, and industrial arts teachers in the State of Louisiana determine the extent to which their basic metals courses are meeting the needs of the youth they serve. It consists of a discussion of course prerequisites, goals, content, and implementation as well as 16 units devoted to various subject areas addressed in a basic metals course. Covered in the units are general safety, basic metalworking tools, layout, bench metalwork, sheet metal, art metal, ornamental metalwork, forging, metal casting, welding, metal finishing, planning, careers in metalworking, and basic metals projects. Each unit contains some or all of the following: objectives, time allotments, suggested topics, student activities, teacher activities, resources, and a unit inventory listing necessary tools and equipment. Among those items appended to the guide are safety rules, steps in making a layout, samples of basic metals projects, a sample student-planning sheet, suggestions for measuring achievement, sample test questions, techniques for conducting classes and for motivating students, and a list of resource materials.
    [Show full text]
  • Metalworking Tools, Equipment & Supplies
    Since 1914 Metalworking Tools, Equipment & Supplies Solutions to Unique & Common Challenges www.gesswein.com For Our Valued Customers The Paul H. Gesswein Company is proud to bring to you our latest brochure featuring exciting new products for finishing and deburring: • Ultramax MF multi-function ultrasonic polisher • Dynabrade air powered tools • Expanded line of Ushio air tools • Shaviv deburring tools • Our popular GMX & G-Flex cotton fiber mounted points in new shapes & sizes • New "Hybrid" Shaped Finishing Stones • Portable Dino-Lite analog and digital microscope systems for inspection, measurement, and documentation Be sure to visit www.gesswein.com for all of the latest products, specials, and technical information. Our "Quick Order" form on the homepage makes ordering fast! Please do not hesitate to give us a phone call to speak with one of our technical specialists should you have any questions: 1-800-544-2043. Thank you for your business and consideration. Table of Contents Page Ultrasonic Finishing 4-5 Finishing Stones 6-7 Power Tools 8-13 Air Tools 14-17 Mounted Stones 18-20 Diamond Tools 21-23 Deburring 24-26 Deburring & Deflashing 27 Deburring & Finishing 28-33 Polishing 34-38 Welding 39 Cleaning 40-41 Magnification & Inspection 42-43 3 ULTRASONIC FINISHING ULTRAMAX® MF (Multi-Function) Polishing & Deburring System New! Reduce finishing time dramatically! The first multi-function system for polishing, deburring, and metal removal. ULTRAMAX MF is supplied with an ultrasonic handpiece, and will power optional mechanical rotary and reciprocating handpieces. Has receptacles for both brush- type and brushless handpieces-the full range of Gesswein Power Hand Handpieces (p.10-13).
    [Show full text]
  • Abrasive Flow Machining: a Case Study
    Journal of Materials Processing Technology, 28 ( 1991 ) 107-116 Elsevier Abrasive flow machining: a case study Larry Rhoades President, Extrude Hone Corp., P.O. Box 527, 8075 Pennsylvania Ave., Irwin, PA 15842, U.S.A. INTRODUCTION Abrasive Flow Machining (AFM) is used to deburr, polish or radius surfaces and edges by flowing a semisolid abrasive media over these areas. The process embraces a wide range of feasible applications: from critical aerospace and medical components to high production volumes of parts. AFM can reach even the most inaccessible areas, processing multiple holes, slots or edges in one operation. Advances in media formulation and tool design coupled with new capabilities in processing and automation have established the abrasive flow process as a way of satisfying tough marmfaetudng requirements economically and productively. The AFM process can be used in a wide range of finishing operations. It can process many areas on a single workpiece or multiple parts simultaneously. Inaccessible areas and complex internal passages can be finished economically and productively. Automatic AFM systems can handle thousands of parts per day, greatly reducing labor costs by eliminating tedious hand worl~ By understanding and controlling the process parameters, AFM can be applied to an impressive range of finishing operations, providing uniform, repeatable, predictable results. In abrasive flow machining two opposed cylinders extrude a semisolid abrasive media back and forth through passages formed by the workpiece and the tooling (Figure 1). The process is abrasive only where the flow is restricted: the extrusion area. The machining action compares to a grinding or lapping operation as the abrasive media gently and uniformly hones the surface or edges.
    [Show full text]