DOCSLIB.ORG

You Can Never Have Too Much Ammo!

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
You Can Never Have Too Much Ammo! Cast Lead Bullets / Hard Cast lead Bullets / Gas Checks Soft Cast Bullets Some bullets require casting with pure soft lead—example: black powder bullets. For these bullets, I use a pure 100% lead, and, if necessary and where required, add an amount of tin necessary to facilitate forming in the mold. Hard Cast Bullets Reloading Bullets Most cast lead bullets are cast using what is known in the industry as a “Lyman Lead Cast #2 Alloy”. This alloy is made by combining 90% pure lead., 5% tin and 5% anti- mony. This gives the bullet a hardness rating of approximately 14-15 BHN (Brinell Hardness Number). For higher pressure/velocity handgun bullets, and rifle bullets, the hardness of the lead is increased to a 17-18 BHN. Bullets may also be cast in a hardness range of 8-13 depending upon the bullet and the average loads for that round. Gas Checks Gas checks are made of copper, aluminum, zinc and sometimes brass. High pressures, such as those associated with maximum loads in magnum handgun cartridges or in rifle cartridges, coupled with cast lead bullets, can lead to lead- Attention Customers: You will receive a 10% discount for all direct ing in the barrel. orders (not online purchases) since we will not have to pay the listing A gas check provides a thin but malleable layer of metal at the base of the lead and/or selling fees. To order, contact us by phone or email. Thank you bullet which provides a seal to the rifling in the barrel, and can eliminate leading. View and Purchase Online at: Howard Fleury www.gunbroker.com 3348 36th Ave S Moorhead, MN 56560-6997 Remember - You can www.gunauction.com Search Seller: PastorHOF 218-790-0099 never have too much Or call / email to order Email: [email protected] ammo! (Pricing effective 05/01/2015 and is subject to change without notice) Rifle Bullets Handgun Bullets .223 Remington Cast Lead - 55g RN with Ruger Old Army Cast Lead - 240g “Kaido Ojamma” Gas Check - Sized to .224 and lubed with Round Flat Nose (RFN) Cast at .456 & Tumble-Lubed Carnauba Red 100 count Price $9.00 with Alox 100 count Price $25.00 .32-20 Cadet 115g Round Nose/Hollow Base—Bullet is cast lead and hollow base is Ruger Old Army Cast Lead - 220g Conical Cast swaged-Sized to .312. Lubed with Carnauba at .456 & Tumble-Lubed with Alox 100 Red. 100 count $22.00 count Price $21.00 .357 Magnum Carbine Cast Lead - 168g SWC 455 Webley Cast Lead - 265g RN Hollow Base— with Gas Check - Sized to .358 & lubed with . Carnauba Red - 250 count Price $33.00 sized to .455 & Lubed with White Label Lube Xlox 2500 Plus. Will tumble lube with Alox on request. Can lube with SPG on request for an additional $10 per 100. 100 count Price $27.00 .375 Win 38-55 .375 H&H 275g FN with Gas Check - Sized to .375 or .377 as desired-lubed with Carnauba Red - 100 count Price $29.00 .30-.30 Carbine Cast Lead - Choice of Three Weights: 150g RNFP / 160g RN / 170g RNFP with Gas Check—Sized to .309 and lubed with Carnauba Red 100 count Price $19.00 BRASS - New Starline Brass available—per quantity of 100: 7mm Cast Lead - 130g RN with Gas Check .357 Magnum $22.00 Sized to .284 and Lubed with Carnauba Red .40 S&W $24.00 100 Count Price $18.00 .44 Remington Magnum $25.00 .45 ACP $25.00 .45 Colt $26.00 8mm Cast Lead - 175g RN with Gas Check .45-70 Government $52.00 Sized to .324 and Lubed with Carnauba Red 100 Count Price $20.00 (Contact us to confirm availability of brass) 7.62x39 Cast Lead - 155g RN with Gas Check Sized to .311 and Lubed with Carnauba Red 100 Count Price $19.00 All shipping is through USPS via Priority Mail. Shipping charges, if neces- .45 - .70 / .450 / .458 Cast Lead - 300g FN sary, are not included. Call or email for shipping. with gas check - Sized to .458 and lubed with Carnauba Red 100 count Price $29.00 Prices listed are subject to change without notice (Effective date: 05/01/2015) Handgun Bullets .380 or 9mm Cast Lead—102g RN - Sized .38 / .357 Cast Lead - 148g WC - Sized to .358 to .356 Lubed with White Label Lube Xlox 2500 Lubed with White Label Lube Xlox 2500 Plus. Plus. 500 count Price: $33.00 500 count Price $38.00 9mm Cast Lead - 120g Conical - Sized .38 / .357 Cast Lead - 150g RNFP—Hollow Point to .356 Lubed with White Label Lube Xlox 2500 - Sized to .358 Lubed with White Label Lube Xlox Plus. 500 count Price $36.00 2500 Plus. 50 count Price $12.00 9mm Cast Lead - 120g TC - Sized to .356 .38 / .357 Cast Lead - 150g RN - Sized to .358 Lubed with White Label Lube Xlox 2500 Plus. Lubed with White Label Lube Xlox 2500 Plus. 500 count Price $36.00 500 count Price $38.00 9mm Cast Lead - 125g RN - Sized to .356 .38 / .357 Cast Lead - 158g SWC - Sized Lubed with White Label Lube Xlox 2500 Plus. to .358 Lubed with White Label Lube Xlox 2500 500 count Price $36.00 Plus. 500 count Price $39.00 9mm Cast Lead - 133g Hollow Point- Lyman Devastator - Sized to .356 Lubed with White .38 / .357 Cast Lead - 158g RNFP - Sized Label Lube Xlox 2500 Plus. 50 count to .358 Lubed with White Label Lube Xlox 2500 Price $12.00 Plus. 500 count Price $40.00 9mm Cast Lead - 147g RNFP BB—IPSC Design - Sized to .356 Lubed with White Label Lube Xlox 2500 Plus. 500 count Price .38 / .357 Cast Lead - 165g RNFP - Sized $39.00 to .358 Lubed with White Label Lube Xlox 2500 Plus. 500 count Price $40.00 9mm Makarov Cast - 95g RN Sized to .365 Lubed with White Label Lube Xlox 2500 Plus. .40 S&W / 10mm Cast Lead - 175g TC - Sized 500 count Price $35.00 to .401 and lubed with Carnauba Red 250 count Price $28.00 .38 / .357 Cast Lead - 125g RNFP - Sized to .358 Lubed with White Label Lube Xlox 2500 .44 Magnum Cast Lead - 245g SWC w/Gas Plus. 500 count Price $36.00 Check - Sized to .430 and lubed with Carnauba Red 100 count Price $25.00 .38 / .357 Cast Lead - 147g SWC - Sized .44 Magnum Cast Lead - 305g RNFP w/Gas to .358 Lubed with White Label Lube Xlox 2500 Check - Sized to .430 and lubed with Plus. 500 count Price $39.00 Carnauba Red 100 count Price $28.00 Handgun Bullets Rifle Bullets .45 ACP Cast Lead - 200g RNFP - Sized .45 - .70 / .450 / .458 Cast Lead - 345g RNFP to .452 and lubed with Carnauba Red 250 - Sized to .458 and lubed with Carnauba Red count Price $25.00 100 count Price $19.00 .45 ACP Cast Lead - 200g SWC - Sized .45 - .70 / .450 / .458 Cast Lead - 405g RNFP to .452 and lubed with Carnauba Red 250 w/Hollow Base - Sized to .458 and lubed with count Price $24.00 Carnauba Red 100 count Price $25.00 .45 ACP Cast Lead - 230g RNFP Hollow Point—Sized to .452 and lubed with Carnauba .45 - .70 / .450 / .458 Cast Lead - 410g RNFP Red 100 count Price $22.00 Sized to .458 and lubed with Carnauba Red 100 count Price $21.00 .45 ACP Cast Lead - 228g RN - Sized to .452 and lubed with Carnauba Red 250 count .45 - .70 / .450 / .458 Cast Lead - 500g Pointed Price $26.00 Round Nose Sized to .458 and lubed with Carnauba Red 100 count Price $24.00 .45 Colt Cast Lead - 255g RNFP - Sized .45 - .70 / .450 / .458 Cast Lead - 500g RNFP to .452 and lubed with Carnauba Red 250 w/gas check Sized to .458 and lubed with count Price $32.00 Carnauba Red 50 count Price $21.00 .45 Colt Cast Lead - 255g SWC - Sized to .452 and lubed with Carnauba Red 250 .50 - .70 Govt. Cast Lead - 450g RNFP or count Price $33.00 500g RNFP—Your Choice—Sized to .512 Lubed with White Label Lube Xlox 2500 Plus. 100 count Price $24.00 .45 Colt / 454 Casull Cast - 320g RNFP with Gas Check - Sized to .452 and lubed with Carnauba Red 100 count Price $27.00 .500 S&W Cast Lead - 440g RNFP with Gas Check - Sized to .501 and lubed with Carnauba Red 50 count Price $19.00 Remington .44 Cal Army Cast Lead - 200g Conical - Cast at .450 & Tumble-Lubed with Alox 100 count Price $19.00 .
Load more

Recommended publications
  • Catalog & Order Form Lead Bullet Technologies
    Lead Bullet Technologies F.I.G ENT., INC. 78592 Hwy 2 Moyie Springs, ID 83845 Catalog & Order Form LBT PREMIUM MOLDS LBT bullet designs are the most copied cast bullets in the world, because, when they are cast in molds manufactured by LBT they are the most accurate bullets available! However, copying the profile of an LBT bullet by cherrying or conventional lathe boring processes, as all other moldmakers do, does not result in molds or bullets that live up to LBT accuracy standards! You see, the heart of all molds, which is the cavities, are produced at LBT with a one of its kind, ultra precision, custom designed, custom built, reducing tracer lathe. This only machine in the world was engineered for the single purpose of producing molds with precision that no available machinery could match. - In the 23 years of its existence, no moldmaker or machine, or mold cutting method has come close to producing LBT quality! - Because of this, the advantages of purchasing your molds from LBT are: 1. Molds which drop their bullets easier then any other mold. 2. Bullets which are better balanced than can be produced in any other molds, because they are round and sound, or free of voids-which equals: 3. Accuracy that is untouchable by bullets from other manufactures molds, even if they have copied our superior designs! Not to mention the design features in LBT molds which ensure void free bullets, flat bases, and extra long service life. LBT sprue plates are designed to minimize the shrink voids and air pockets which unbalance bullets and destroy accuracy, and are equipped with spring hold downs at two points, which prevent the sprue plate from lifting off the mold and causing finned and out of square bases.
    [Show full text]
  • Handloading the .327 Federal Magnum
    Load Development The .327 Federal Magnum was introduced in a Ruger SP101 six-shot revolver. Brian Pearce ederal Cartridge has teamed jacketed bullet 1,400 fps and a Speer with Sturm, Ruger & Com- 115-grain Gold Dot hollowpoint Fpany to introduce a com- 1,300 fps; a Federal “Low Recoil” pletely modern .32-caliber cartridge load pushes an 85-grain Hydra- known as the .327 Federal Mag- Shok 1,330 fps. These velocities num. It is essentially a lengthened are advertised from a Ruger SP101 version of the .32 H&R Magnum revolver with a 31/16-inch barrel. For cartridge with a case length of 1.200 the record, those speeds are realistic, inches, but it’s loaded to signifi- as the test revolver used herein pro- cantly greater pressures of 45,000 duced greater velocities than factory psi. In spite of its name, it utilizes claims. the same .312-inch bullets as other The Ruger SP101 is a small- .32-caliber cartridges, including the frame, double-action revolver, and .32 S&W Long, .32 H&R Magnum when chambered in .327 Federal and .32 WCF (aka .32-20). Magnum, it features six shots rather The .327 Federal Magnum of- than five when the same gun is The .327 Federal Magnum (left) is essentially fers substantial performance and chambered in .38 Special or .357 a lengthened .32 H&R Magnum (right) but is advertised to drive a 100-grain Magnum. This is a stout and un- loaded to significantly greater pressures. 1 LOAD DEVELOPMENT • May-June 2009 loaddata.com Handloading the .327 Federal Magnum Case length for the .327 Federal Magnum is 1.200 inches.
    [Show full text]
  • Driving Bands
    These are the bands placed around projectiles to prevent the forward loss of gas around the projectile. They are usually made from copper, gilding metal and sometimes sintered iron. The modern day has intruded here also and they will now be encountered in plastic versions. Their use and introduction can be traced back to the time when cylindrical projectiles first appeared. The original round cannonball because of its requirement to be loaded from the muzzle had no method of sealing the bore. In fact had the ball been tight enough to seal the bore you wouldn't have been able to load the weapon at all. All this changed when the Cylindro-ogival projectile arrived on the scene along with the not-new breech loading weapons. (They had been tried many years before but failed through the inability of the gunners to adequately seal the breeches). A round cannonball needs no stabilizing. Because of its spherical shape it is inherently stable. Ask any cricketer, golfer or baseballer. On the other hand the Cylindro-ogival projectile is inherently unstable. It will not fly very well at all unless it is stabilized in some way. The two basic methods of stabilizing an elongated projectile are: • Fin stabilization and, • Spin stabilization. Both of these methods are in current use in the world today. To provide adequate stability for a projectile using fins there needs to be FIN STABILISATION. some sort of protection for the fins. The arrow of your ancient bowman would not survive in the bore of a cannon without some form of protection.
    [Show full text]
  • Rimfire Firing-Pin Indent Copper Crusher (Part 1)
    NONFERROUSNONFERROUS HEATHEAT TREATING TREATING Rimfire Firing-Pin Indent Copper Crusher (part 1) Daniel H. Herring – The HERRING GROUP, Inc.; Elmhurst, Ill. The Sporting Arms and Ammunition Manufacturers’ Institute Inc., also known as SAAMI, is an association of the nation’s leading manufacturers of rearms, ammunition and components. SAAMI is the American National Standards Institute-accredited standards Fig. 1. Firing-pin indent copper crushers developer for the commercial small arms and ammunition industry. SAAMI was for 22-caliber rimfire ammunition founded in 1926 at the request of the federal government and tasked with: creating and (courtesy of Cox Manufacturing and publishing industry standards for safety, interchangeability, reliability and quality; and Kirby & Associates) coordinating technical data to promote safe and responsible rearms use. he story of SAAMI’s rimfire firing-pin indent copper pressures and increased bullet velocities. crusher describes the reinvention of one of the most The primary advantage of rimfire ammunition is low cost, important tools in the ammunition and firearms industry typically one-fourth that of center fire. It is less expensive to T(Fig. 1). This article explains the purpose and operation manufacture a thin-walled casing with an integral-rimmed of the rimfire firing-pin indent copper crusher and how an primer than it is to seat a separate primer in the center of the unusual chain of events almost led to the disappearance of this head of the casing. simple but important technology. The most common rimfire ammunition is the 22LR (22-caliber long rif le). It is considered the most popular round Rimfire Ammunition in the world and is commonly used for target shooting, small- In order to discuss the rimfire copper crusher, we need to take a game hunting, competitive rifle shooting and, to a lesser extent, step back and first explain what rimfire ammunition is and how it works.
    [Show full text]
  • Loads Are Keeping the .44 Magnum at the Top of The
    Pushing The Envelope Since the late 1990s Randy Garrett has been producing a 330-grain Super Hard Cast Long-Hammerhead at 1,385 fps. Custom gunsmith John Gallagher introduced me to it several years ago. I have found that if you run into John out hunting, he will likely have a cylinderful of Garrett 330s in his custom Ruger Bisley. When Hamilton Bowen went hunting up in Alaska last year, he was camping out in brown bear county. At night he slept with a Redhawk on a lanyard. No, it wasn’t a .475 or .500. It was, in fact, one of his 4-inch ost .44 Magnum shooters may not real- revolvers allows is a longer overall loaded- Kodiak conversions in .44 Mag loaded with Garrett’s 330s. Long cylinders and specialized mega- I’ve been so impressed with the additional performance loads are keeping the .44 Magnum at ize the significance of the extra-long cartridge length. Generally, this means we afforded by having a .44 that works with this type of ammo the top of the heavyweight division. cylinders featured in Ruger Redhawk, can have an extra-heavy bullet seated to less that I now have two custom Blackhawks and a takedown Dan Wesson and a few other revolvers. What depth, thus gaining more room for powder. Marlin rifle specifically built to chamber the Garrett 330. By Ashley Emerson the longer cylinder on these heavy-duty And with a cartridge loaded long—and to Randy Garrett has for years specialized in high-perfor- mance .44 Mag and .45-70 ammo.
    [Show full text]
  • William R. Meehan and John F. Thilenius WILLIAM R
    Pacific Northwest Forest and Range Experiment Station h General Technical Report PNW-152 March 1983 William R. Meehan and John F. Thilenius WILLIAM R. MEEHAN is fisheries The use of trade, firm, or corporation research project leader, and JOHN F. names in this publication is for the THILENIUS is a research wildlife information and convenience of the biologist, Pacific Northwest Forest and reader. Such use does not constitute Range Experiment Station, Forestry an official endorsement or approval by Sciences Laboratory, PO. Box 909, the U.S. Department of Agriculture of Juneau, Alaska 99802. any product or service to the exclusion of others that may be suitable. Meehan, William R.; Thilenius, John F. Brown bears (Ursus arctos) are found The difficulties of training inexperi- Safety in bear country: protective from the seashore to the alpine zone enced persons to properly use large- measures and bullet performance at on the islands and mainland along caliber rifles might be lessened by short range. Gen. Tech. Rep. PNW- most of the Pacific coast of Alaska.’ using smaller caliber weapons. Recoil, 152. Portland, OR: US. Department The brown bear is a large, fast-moving muzzle blast, and rifle weight could be of Agriculture, Forest Service, animal, unpredictable in its response to decreased, but possibly at the expense Pacific Northwest Forest and Range humans, and a definite hazard to those of killing power. To provide an Experiment Station; 1983.16 p. who must work in areas inhabited by inadequate weapon just because it was bears. more pleasant to shoot would be un- Bears are frequently encountered by wise.
    [Show full text]
  • Load Guide for Rifle and Handgun
    EDITION 3.5 EDITION 30 AR, 30 T/C, and 6mmx45 and T/C, 30 AR, 30 New data for: for: data New • The most up-to-date and comprehensive 223 Rem data available data Rem 223 comprehensive and up-to-date most The • INCLUDES: GUN H D N A AND RIFLE FOR GUIDE LOAD PO Box 158 • Miles City, Montana 59301 Other superior products available ONLY from Western Powders include: RELOADING POWDERS Gun Care Products EDITION 3.5 WARNINGS COMPONENT WARNINGS This guide is intended to be used as a reference. Each individual Primers handloader must determine what is the best and safest load for their 1. NEVER MIX PRIMER BRANDS from different manufacturers; equipment. The loads described in this guide were generated at the 2. Store primers in their original packaging(s) in a cool, dry place. ballistics test facilities of Western Powders, Inc. in accordance with Exposure to heat causes primer deterioration; SAAMI (Shooting Arms and Ammunition Institute) guidelines. All 3. Do not stockpile primers or store in bulk. Storing primers in this loads are fired through test barrels and individual results fired through manner can lead to mass detonation if a primer ignites; different firearms may vary. The handloader is cautioned to read and 4. Do not de-cap live or new primers - fire them in the appropriate follow safe reloading practices such as those outlined in the NRA gun and then de-cap; Guide to Reloading before attempting to reload any cartridge. 5. For best results, use the mildest primer consistent with good ignition; 6.
    [Show full text]
  • And Lastly, by a Taper-Reamer for the Gas-Che
    CONSTRUCTION OF NAVAL GUNS roughing slope bit; fourth, by a finish packed bit; fifth, by a finish slope bit; and lastly, by a taper-reamer for the gas-che<;k slope. The finishing bits are long, of the exact diameter of the chamber (that is, ground so as to bore to the exact diameter) . For guns having the enlarged chamber, as the 6-inch, Mark VI, and 12- inch, Mark III, a different method is pursued. The chamber is nrst roughed out with a hog bit, .then two packed bits are used and two slope bits. The powder chamber being larger than the mouth (or entrance) must be bored with a special boring bar and tool. This bar is hollowed, and is provided with a cutter that can be set out any desired amount by means of internal gearing worked from the outside clear of the breech. Finally the gas-check slope is finished with a taper-reamer. The chambers for R. F. guns are tapered to receive fixed ammu­ nition. Usually they are roughed out to desired taper, using a boring bar carrying a cutter fed in by hand, the rear end of bar being thrown out of line with gun's axis. Chambers having a straight part, and the compression slope, are roughed out with a packed bit. The finishing cut is now taken with a long packe;:l bit, or reamer, ground so as to bore the chamber to exact dimen­ sions. This bit mllst be very accurately made and carefully in­ spected by the officer supervising the work.
    [Show full text]
  • American Rifleman 1970 04.Pdf
    ~Wildcat' Cartridge Packs Kick .357/.44 B&D handgun load has shocking power, long range The recoil of the .357/.44 is heavy but not punishing. 8y 808 MILEK as this high potential cartridge can be brass through the .357/.44 B&D full- OULD you like to work with a W loaded to best even the mighty .44 length sizing die. Case forming requires new magnum-class handgun car- Magnum in factory handgun loadings. very little physical effort, but cases must tridge with an energy potential like the The .357/.44 B&D isn't new in the be well lubricated to keep them from kick of a Missouri mule? If so, consider strictest sense of the word; an earlier sticking in the die. The finished case the .357/.44 Bain & Davis. The des- version was reported on by Dan Cot- is 1.290" long and slips easily into the ignation of this non-standard 'wildcat' terman in the January 1964 issue of chamber of my Contender pistol, with- cartridge is as much a mouthful to say Gun World. He called this cartridge the out the need of trimming. I established as the Thompson/ Center Contender pis- Davis .44/ .357, and it was a little dif- this as my maximum case length and tol chambered for it is a handful to shoot. ferent from the Thompson/Center ver- keep my cases trimmed to that length. sion, having a longer neck and sharper Made by necking down .44 Magnum shoulder. Cotterman's tests were carried brass to accept .357-inch diameter bul- A wide selection out with a converted S&W Model 27 lets, the .357/.44 B&D is a stubby, not- revolver with 834" barrel.
    [Show full text]
  • Gas Checked PB Bullets
    Gas Checked PB Bullets I’ve sat at the loading bench many times and looked at Lyman’s 457122HP design and thought what a perfect design it was. It has shot well for me in my Ruger Number 1 .45/70 and also in my M1895 Marlin .45/70 with Ballard style rifling. I yearly send some to a friend in Vermont who has a micro groove Marlin and he reports good hunting accuracy in his rifle. The only drawback is that this bullet normally drops from the mould with a fairly small diameter and I get leading in the Number 1 and occasionally in the Marlin when using shotgun powders. If only Ideal/Lyman had seen fit to bring forth a design in this same style with a gas check on it, it would be perfect. With these thoughts in mind, Orygun Mark and myself have been working on swaging a GC shank on the 358430 200 grain version for our .35 Remington Marlins for about two years with the ultimate goal of making a gas checked version of the 457122HP. After hundreds of e-mails and dozens of experiments, we were successful on the 358430 but some bullet distortion did occur and this is undesirable. Trying the same methods on the 457122HP resulted in failure as the drastic swaging of the base elongated the bullet more than was acceptable. What we needed was a method to easily GC any PB bullet for rifle use without a bench full of expensive, hard to fabricate tools. One night I was reading an old article on Wilk gas checked bullets for higher velocities in rifles.
    [Show full text]
  • Table of Contents Standard Reloading Dies (Group A-E)
    HUNTINGTON DIE SPECIALTIES - 2014 rcbs dies table oF contents Standard Reloading Dies (Group A-E) ................. 35-36, 74-76 AR Series Dies / TC Seating Dies ........................................ 37 Competition Die Sets ...................................................... 39, 78 Cowboy Action Shooting Dies (CAS) .............................. 38, 78 Cowboy Shotshell Dies ......................................................... 38 Legacy Series Dies ......................................................... 37, 78 reloading presses Safari Series Dies ............................................................ 37, 79 Reloading Presses, Kits, & Accessories ..............................1-5 50 bmg, 416 Barrett, 460 Steyr Dies, Large Caliber ........ 38, 76 Compac Press, HDS ............................................................... 5 Neck Die Sets / Neck Sizer Dies ......................................41-42 Specialty Merchandise Information ...................................... 51 Small Base Sets / Small Base Sizers ...............................42-43 powder handling tools Die Replacement Parts ......................................................... 43 Reloading Scales, Electronic / Beam...................................5-6 Expander-Decap Units ..............................................43, 74-79 Powder Measures / Tools ....................................................6-9 Hornady Carbide Expander Assy. ......................................... 43 Bullet Feeding Systems .........................................................
    [Show full text]
  • Ballistic Pressure Sensor Reference Guide
    BALLISTIC PRESSURE SENSOR REFERENCE GUIDE pcb.com/ballistic | 1 800 828 8840 This compilation is intended as a reference guide to the characteristics and behavior of firearms and ammunition, and as an introduction to the various types of ballistics measurements that are made. Dimensions shown on figures BALLISTIC TERMINOLOGY are in inches. ANNEALED: Description of metal heated after work hardening CENTER FIRE: Refers to centrally located primer in base to prevent it from being too brittle. of metal cartridges. BARREL TIME: Time between the impact of the firing pin CHAMBER: That part of the bore, at the breech, formed to on the primer and when the bullet exits the muzzle. accept and support the cartridge. BELT: Area of cartridge case with an increased or reinforced FLASH HOLE: The hole leading from the primer pocket into diameter ahead of extractor groove. the body of the cartridge case. BORE: The inside of the barrel of a gun, the inside diameter GAUGE: Commonly refers to the size of a shot shell (the of the barrel before rifling is cut. smaller the number, the larger the shell). BRASS: Term often applied to empty cartridge cases; an GROOVES: Spiral cuts or impressions in the bore of a gun alloy of copper and zinc. that causes a bullet to spin as it moves through the barrel. BREECH: The area of a firearm at the rear of the bore that IGNITION: The setting on fire of the propellant powder receives the cartridge case. charge, by the primer. BULLET: The missile only. Becomes a projectile when LANDS: The spiral raised portion of a bore remaining after in flight.
    [Show full text]