Equal-Loudness-Level Contours of Older Adults Measured By

Total Page:16

File Type:pdf, Size:1020Kb

Equal-Loudness-Level Contours of Older Adults Measured By Acoust. Sci. & Tech. 30, 6 (2009) #2009 The Acoustical Society of Japan Equal-loudness-level contours of older adults measured by magnitude estimation method: A preliminary study Kenji Kurakataà National Institute of Advanced Industrial Science and Technology (AIST), AIST Tsukuba Central 6, 1–1–1 Higashi, Tsukuba, 305–8566 Japan ( Received 7 May 2009, Accepted for publication 21 May 2009 ) Keywords: Equal-loudness-level contour, Aging effect, Magnitude estimation method PACS number: 43.66.Cb, 43.66.Sr [doi:10.1250/ast.30.446] 1. Introduction The pure tones were presented to listeners in an anechoic Equal-loudness-level contours (ELLCs) show combina- room via a loudspeaker (DS-205; Mitsubishi Electric Corp.). tions of sound pressure levels and frequencies of pure tones The listener sat on a chair facing the loudspeaker at a distance that are perceived as being equally loud. An ISO standard [1] of 2.5 m. specifies normal ELLCs in a free field that were determined The ME method without a modulus was used to measure for otologically normal persons aged 18–25 years inclusive. the loudness of pure-tone stimuli, which were presented to As humans age, their auditory system’s characteristics listeners one by one in random order. After each presentation, change progressively. For that reason, older adults are expected the listeners assigned the stimulus a positive number that they to show different ELLCs. However, few attempts (e.g., thought corresponded to the magnitude of loudness and Ref. [2]) at measuring age-related changes of loudness per- responded orally. Each listener performed three trials for each ception have been reported so far. A possible hindrance of such stimulus. The first trials were for practice and were excluded measurements is that individual differences in hearing ability from analyses. The measurement time per listener was about changes among older adults are greater than those among 30 min. young adults. Consequently, more subjects must be examined Study participants were 12 young adults and 35 older to present a good overall picture of their loudness perception. adults. After screening for abnormalities in their audiometric The magnitude estimation (ME) method can measure the profiles, data taken from 10 young adults (age range, 22–27 sensory magnitude efficiently, including the tone loudness. In years; median, 25 years) and 28 older adults (age range, 61– most cases, few responses are necessary for each subject to 86 years; median, 69.5 years) were adopted. The male and estimate one value on a psychophysical magnitude function. female listeners were equinumerous. They had no previous Although ME has been criticized as being subject to various experience in magnitude estimation tasks or other psycho- biases [3], this method might be useful for obtaining ELLCs acoustic experiments. for numerous listeners in a short time. Schneider et al. [4] examined the applicability of ME 3. Derivation of ELLCs to deriving ELLCs. They were able to obtain contours. The geometrical mean of the two numbers assigned to However, the contours were not directly comparable to the each stimulus was first calculated to obtain a magnitude well-established ones in the ISO standard because of their estimate of individual listeners. Then, group medians of measurement condition (monaural listening using an ear- young and older listeners were calculated for each stimulus. 2n 2n phone). Listeners were all students under 30 years of age. A loudness function, expressed as É ¼ kðP À P0 Þ [5], In this Letter, I report the results of a preliminary study in was fitted to estimates of listener groups for each frequency which ELLCs were derived from magnitude estimates of pure tone. In the equation, É is the magnitude estimate of tones; the listeners were young and older adults. The loudness, P is the sound pressure of the stimulus tone, and applicability of the ME method to ELLC measurement for k and n respectively signify parameters that determine the older adults is examined. form of the function. In addition, P0 is the sound pressure of the stimulus tone at the threshold, as measured for each 2. ME for pure tones frequency before the experiment, employing the same Pure tones with a duration of 1 s were used as stimuli. The listeners. frequency was 125, 250, 500, 1,000, 2,000, 4,000, or 8,000 Hz. An assumption was made to derive ELLCs: tones to The sound pressure level was varied in 10 dB steps from 25 dB which the same number had been assigned by listeners were at to 85 dB for the 125, 250, and 8,000 Hz tones and from 15 dB to the same loudness, irrespective of their tone frequency. Once 75 dB for tones of other frequencies. Consequently, the number the loudness functions at 1,000 Hz and other frequencies are of stimuli were 49 (7 frequencies  7 levels) in total. obtained, ELLCs can be drawn by connecting sound pressure levels of tones with different frequencies but the same Ãe-mail: [email protected] loudness É. 446 K. KURAKATA: EQUAL-LOUDNESS-LEVEL CONTOURS OF OLDER ADULTS Fig. 1 ELLCs of ISO standard [1] (dotted lines) and Fig. 2 ELLCs of young listeners (dotted lines) and older those of young listeners measured by the ME method listeners (solid lines with filled circles) measured by (solid lines with filled circles). The hearing thresholds the ME method. The hearing thresholds are also shown are also shown for comparison (ISO standard, dashed for comparison (young listeners, dashed line; older line; present study, solid line with open circles). listeners, solid line with open circles). Figure 1 presents the ELLCs in the ISO standard and 4. Conclusion those of young listeners measured using ME. These two sets The results of this study indicate that the ME method was of ELLCs show good agreement, except at the highest able to yield ELLCs comparable to those in the ISO standard frequencies at high loudness levels. The discrepancy between obtained with other measurement methods. Using the ME the two sets of ELLCs was very small, considering that the method, ELLCs for numerous older adults are obtainable in a contours of this study were obtained from only 10 listeners short time. Those ELLCs will clarify the age-related change and that the variation among studies used for ISO ELLC in loudness perception. construction was 10 dB or more in some cases [1]. Therefore, ME can produce ELLCs efficiently with precision comparable References to those of other psychophysical methods, such as the method [1] ISO 226, Acoustics — Normal equal-loudness-level contours of constant stimuli and the bracketing method. (International Organization for Standardization, Geneva, 2003). Figure 2 portrays ELLCs of young and older listener [2] D. W. Robinson and M. A. Dadson, ‘‘A re-determination of the groups measured using ME. Some aging effects are observ- equal-loudness relations for pure tones,’’ Br. J. Appl. Phys., 7, able in the figure. First, the older listener group was less 166–181 (1956). sensitive to high-frequency tones of 4,000 Hz and higher than [3] G. A. Gescheider, Psychophysics: the Fundamentals, 3rd ed. was the young listener group. The contours of older listeners (Lawrence Erlbaum Associates, Mahwah, N.J., 1997), pp. 332– show steady growth as the frequency increases above 334. [4] B. Schneider, A. A. Wright, W. Edelheit, P. Hock and C. 1,000 Hz, whereas those of young listeners distinctly show Humphrey, ‘‘Equal loudness contours derived from sensory a dip at 4,000 Hz. Second, the older listener group was magnitude judgments,’’ J. Acoust. Soc. Am., 51, 1951–1959 apparently more sensitive to low-frequency tones of 250 Hz (1972). and below than was the young listener group. This lowering [5] J. P. A. Lochner and J. F. Burger, ‘‘Form of the loudness does not mean that older adults can hear tones of those function in the presence of masking noise,’’ J. Acoust. Soc. Am., frequencies better than do young adults. Rather, it suggests 33, 1705–1707 (1961). that the relative sensitivity to low-, middle-, and high- frequency tones differs between the two age groups. 447.
Recommended publications
  • Acoustical Engineering
    National Aeronautics and Space Administration Engineering is Out of This World! Acoustical Engineering NASA is developing a new rocket called the Space Launch System, or SLS. The SLS will be able to carry astronauts and materials, known as payloads. Acoustical engineers are helping to build the SLS. Sound is a vibration. A vibration is a rapid motion of an object back and forth. Hold a piece of paper up right in front of your lips. Talk or sing into the paper. What do you feel? What do you think is causing the vibration? If too much noise, or acoustical loading, is ! caused by air passing over the SLS rocket, the vehicle could be damaged by the vibration! NAME: (Continued from front) Typical Sound Levels in Decibels (dB) Experiment with the paper. 130 — Jet takeoff Does talking louder or softer change the vibration? 120 — Pain threshold 110 — Car horn 100 — Motorcycle Is the vibration affected by the pitch of your voice? (Hint: Pitch is how deep or 90 — Power lawn mower ! high the sound is.) 80 — Vacuum cleaner 70 — Street traffic —Working area on ISS (65 db) Change the angle of the paper. What 60 — Normal conversation happens? 50 — Rain 40 — Library noise Why do you think NASA hires acoustical 30 — Purring cat engineers? (Hint: Think about how loud 20 — Rustling leaves rockets are!) 10 — Breathing 0 — Hearing Threshold How do you think the noise on an airplane compares to the noise on a rocket? Hearing protection is recommended at ! 85 decibels. NASA is currently researching ways to reduce the noise made by airplanes.
    [Show full text]
  • Standing Waves and Sound
    Standing Waves and Sound Waves are vibrations (jiggles) that move through a material Frequency: how often a piece of material in the wave moves back and forth. Waves can be longitudinal (back-and- forth motion) or transverse (up-and- down motion). When a wave is caught in between walls, it will bounce back and forth to create a standing wave, but only if its frequency is just right! Sound is a longitudinal wave that moves through air and other materials. In a sound wave the molecules jiggle back and forth, getting closer together and further apart. Work with a partner! Take turns being the “wall” (hold end steady) and the slinky mover. Making Waves with a Slinky 1. Each of you should hold one end of the slinky. Stand far enough apart that the slinky is stretched. 2. Try making a transverse wave pulse by having one partner move a slinky end up and down while the other holds their end fixed. What happens to the wave pulse when it reaches the fixed end of the slinky? Does it return upside down or the same way up? Try moving the end up and down faster: Does the wave pulse get narrower or wider? Does the wave pulse reach the other partner noticeably faster? 3. Without moving further apart, pull the slinky tighter, so it is more stretched (scrunch up some of the slinky in your hand). Make a transverse wave pulse again. Does the wave pulse reach the end faster or slower if the slinky is more stretched? 4. Try making a longitudinal wave pulse by folding some of the slinky into your hand and then letting go.
    [Show full text]
  • Nuclear Acoustic Resonance Investigations of the Longitudinal and Transverse Electron-Lattice Interaction in Transition Metals and Alloys V
    NUCLEAR ACOUSTIC RESONANCE INVESTIGATIONS OF THE LONGITUDINAL AND TRANSVERSE ELECTRON-LATTICE INTERACTION IN TRANSITION METALS AND ALLOYS V. Müller, G. Schanz, E.-J. Unterhorst, D. Maurer To cite this version: V. Müller, G. Schanz, E.-J. Unterhorst, D. Maurer. NUCLEAR ACOUSTIC RESONANCE INVES- TIGATIONS OF THE LONGITUDINAL AND TRANSVERSE ELECTRON-LATTICE INTERAC- TION IN TRANSITION METALS AND ALLOYS. Journal de Physique Colloques, 1981, 42 (C6), pp.C6-389-C6-391. 10.1051/jphyscol:19816113. jpa-00221175 HAL Id: jpa-00221175 https://hal.archives-ouvertes.fr/jpa-00221175 Submitted on 1 Jan 1981 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. JOURNAL DE PHYSIQUE CoZZoque C6, suppZe'ment au no 22, Tome 42, de'cembre 1981 page C6-389 NUCLEAR ACOUSTIC RESONANCE INVESTIGATIONS OF THE LONGITUDINAL AND TRANSVERSE ELECTRON-LATTICE INTERACTION IN TRANSITION METALS AND ALLOYS V. Miiller, G. Schanz, E.-J. Unterhorst and D. Maurer &eie Universit8G Berlin, Fachbereich Physik, Kiinigin-Luise-Str.28-30, 0-1000 Berlin 33, Gemany Abstract.- In metals the conduction electrons contribute significantly to the acoustic-wave-induced electric-field-gradient-tensor (DEFG) at the nuclear positions. Since nuclear electric quadrupole coupling to the DEFG is sensi- tive to acoustic shear modes only, nuclear acoustic resonance (NAR) is a par- ticularly useful tool in studying the coup1 ing of electrons to shear modes without being affected by volume dilatations.
    [Show full text]
  • Recent Advances in the Sound Insulation Properties of Bio-Based Materials
    PEER-REVIEWED REVIEW ARTICLE bioresources.com Recent Advances in the Sound Insulation Properties of Bio-based Materials Xiaodong Zhu,a,b Birm-June Kim,c Qingwen Wang,a and Qinglin Wu b,* Many bio-based materials, which have lower environmental impact than traditional synthetic materials, show good sound absorbing and sound insulation performances. This review highlights progress in sound transmission properties of bio-based materials and provides a comprehensive account of various multiporous bio-based materials and multilayered structures used in sound absorption and insulation products. Furthermore, principal models of sound transmission are discussed in order to aid in an understanding of sound transmission properties of bio-based materials. In addition, the review presents discussions on the composite structure optimization and future research in using co-extruded wood plastic composite for sound insulation control. This review contributes to the body of knowledge on the sound transmission properties of bio-based materials, provides a better understanding of the models of some multiporous bio-based materials and multilayered structures, and contributes to the wider adoption of bio-based materials as sound absorbers. Keywords: Bio-based material; Acoustic properties; Sound transmission; Transmission loss; Sound absorbing; Sound insulation Contact information: a: Key Laboratory of Bio-based Material Science and Technology (Ministry of Education), Northeast Forestry University, Harbin 150040, China; b: School of Renewable Natural Resources, LSU AgCenter, Baton Rouge, Louisiana; c: Department of Forest Products and Biotechnology, Kookmin University, Seoul 136-702, Korea. * Corresponding author: [email protected] (Qinglin Wu) INTRODUCTION Noise reduction is a must, as noise has negative effects on physiological processes and human psychological health.
    [Show full text]
  • Psychoacoustics and Its Benefit for the Soundscape
    ACTA ACUSTICA UNITED WITH ACUSTICA Vol. 92 (2006) 1 – 1 Psychoacoustics and its Benefit for the Soundscape Approach Klaus Genuit, André Fiebig HEAD acoustics GmbH, Ebertstr. 30a, 52134 Herzogenrath, Germany. [klaus.genuit][andre.fiebig]@head- acoustics.de Summary The increase of complaints about environmental noise shows the unchanged necessity of researching this subject. By only relying on sound pressure levels averaged over long time periods and by suppressing all aspects of quality, the specific acoustic properties of environmental noise situations cannot be identified. Because annoyance caused by environmental noise has a broader linkage with various acoustical properties such as frequency spectrum, duration, impulsive, tonal and low-frequency components, etc. than only with SPL [1]. In many cases these acoustical properties affect the quality of life. The human cognitive signal processing pays attention to further factors than only to the averaged intensity of the acoustical stimulus. Therefore, it appears inevitable to use further hearing-related parameters to improve the description and evaluation of environmental noise. A first step regarding the adequate description of environmental noise would be the extended application of existing measurement tools, as for example level meter with variable integration time and third octave analyzer, which offer valuable clues to disturbing patterns. Moreover, the use of psychoacoustics will allow the improved capturing of soundscape qualities. PACS no. 43.50.Qp, 43.50.Sr, 43.50.Rq 1. Introduction disturbances and unpleasantness of environmental noise, a negative feeling evoked by sound. However, annoyance is The meaning of soundscape is constantly transformed and sensitive to subjectivity, thus the social and cultural back- modified.
    [Show full text]
  • Infrasound and Ultrasound
    Infrasound and Ultrasound Exposure and Protection Ranges Classical range of audible frequencies is 20-20,000 Hz <20 Hz is infrasound >20,000 Hz is ultrasound HOWEVER, sounds of sufficient intensity can be aurally detected in the range of both infrasound and ultrasound Infrasound Can be generated by natural events • Thunder • Winds • Volcanic activity • Large waterfalls • Impact of ocean waves • Earthquakes Infrasound Whales and elephants use infrasound to communicate Infrasound Can be generated by man-made events • High powered aircraft • Rocket propulsion systems • Explosions • Sonic booms • Bridge vibrations • Ships • Air compressors • Washing machines • Air heating and cooling systems • Automobiles, trucks, watercraft and rail traffic Infrasound At very specific pitch, can explode matter • Stained glass windows have been known to rupture from the organ’s basso profunda Can incapacitate and kill • Sea creatures use this power to stun and kill prey Infrasound Infrasound can be heard provided it is strong enough. The threshold of hearing is determined at least down to 4 Hz Infrasound is usually not perceived as a tonal sound but rather as a pulsating sensation, pressure on the ears or chest, or other less specific phenomena. Infrasound Produces various physiological sensations Begin as vague “irritations” At certain pitch, can be perceived as physical pressure At low intensity, can produce fear and disorientation Effects can produce extreme nausea (seasickness) Infrasound: Effects on humans Changes in blood pressure, respiratory rate, and balance. These effects occurred after exposures to infrasound at levels generally above 110 dB. Physical damage to the ear or some loss of hearing has been found in humans and/or animals at levels above 140 dB.
    [Show full text]
  • Sound Acoustics in the Workplace from the Floor up Image: Philips HQ, DACH 3
    Sound acoustics in the workplace From the floor up Image: Philips HQ, DACH 3 Happy, healthy people make a better business When people feel comfortable in their The physical workplace environment plays a major workplace, they’re more productive. role. Employee well-being is vital to any Research has also shown that employees rank it organisation, and controlling noise is as one of the top three factors contributing to job central to this. satisfaction, as well as to their decisions about accepting or leaving a job. At Interface we know that our physical experiences impact on how we feel. And we understand the importance of having a great place to work. Designers and architects have a crucial role to play in providing inspirational environments that facilitate flexible working, for the benefit of both employers and employees. Image: Discovery, ZA Image: Discovery, Modular flooring for flexible, quieter spaces 5 Open-plan spaces are increasingly popular, as they support collaboration and creativity – but they can also be noisy. And disruptive sound levels are high on the list of workplace complaints. Generally, employees feel much happier and more relaxed if they can move around and interact freely with colleagues. But the open-plan design that allows this also poses acoustic challenges. To help solve this problem, we’ve developed modular flooring specifically for the changing workplace. Our extensive ranges of carpet tiles and LVT offer the variety of design, and versatility in function, you need to support all kinds of activities – from quiet concentration to teamwork and recreation. Modular flooring is also ideal for zoning areas for a range of activities, from collaboration and concentration to relaxation and recreation.
    [Show full text]
  • Acoustics: the Study of Sound Waves
    Acoustics: the study of sound waves Sound is the phenomenon we experience when our ears are excited by vibrations in the gas that surrounds us. As an object vibrates, it sets the surrounding air in motion, sending alternating waves of compression and rarefaction radiating outward from the object. Sound information is transmitted by the amplitude and frequency of the vibrations, where amplitude is experienced as loudness and frequency as pitch. The familiar movement of an instrument string is a transverse wave, where the movement is perpendicular to the direction of travel (See Figure 1). Sound waves are longitudinal waves of compression and rarefaction in which the air molecules move back and forth parallel to the direction of wave travel centered on an average position, resulting in no net movement of the molecules. When these waves strike another object, they cause that object to vibrate by exerting a force on them. Examples of transverse waves: vibrating strings water surface waves electromagnetic waves seismic S waves Examples of longitudinal waves: waves in springs sound waves tsunami waves seismic P waves Figure 1: Transverse and longitudinal waves The forces that alternatively compress and stretch the spring are similar to the forces that propagate through the air as gas molecules bounce together. (Springs are even used to simulate reverberation, particularly in guitar amplifiers.) Air molecules are in constant motion as a result of the thermal energy we think of as heat. (Room temperature is hundreds of degrees above absolute zero, the temperature at which all motion stops.) At rest, there is an average distance between molecules although they are all actively bouncing off each other.
    [Show full text]
  • Chapter 12: Physics of Ultrasound
    Chapter 12: Physics of Ultrasound Slide set of 54 slides based on the Chapter authored by J.C. Lacefield of the IAEA publication (ISBN 978-92-0-131010-1): Diagnostic Radiology Physics: A Handbook for Teachers and Students Objective: To familiarize students with Physics or Ultrasound, commonly used in diagnostic imaging modality. Slide set prepared by E.Okuno (S. Paulo, Brazil, Institute of Physics of S. Paulo University) IAEA International Atomic Energy Agency Chapter 12. TABLE OF CONTENTS 12.1. Introduction 12.2. Ultrasonic Plane Waves 12.3. Ultrasonic Properties of Biological Tissue 12.4. Ultrasonic Transduction 12.5. Doppler Physics 12.6. Biological Effects of Ultrasound IAEA Diagnostic Radiology Physics: a Handbook for Teachers and Students – chapter 12,2 12.1. INTRODUCTION • Ultrasound is the most commonly used diagnostic imaging modality, accounting for approximately 25% of all imaging examinations performed worldwide nowadays • Ultrasound is an acoustic wave with frequencies greater than the maximum frequency audible to humans, which is 20 kHz IAEA Diagnostic Radiology Physics: a Handbook for Teachers and Students – chapter 12,3 12.1. INTRODUCTION • Diagnostic imaging is generally performed using ultrasound in the frequency range from 2 to 15 MHz • The choice of frequency is dictated by a trade-off between spatial resolution and penetration depth, since higher frequency waves can be focused more tightly but are attenuated more rapidly by tissue The information in an ultrasonic image is influenced by the physical processes underlying propagation, reflection and attenuation of ultrasound waves in tissue IAEA Diagnostic Radiology Physics: a Handbook for Teachers and Students – chapter 12,4 12.1.
    [Show full text]
  • Sound, Frequency and Healing
    By Robin Richardson If you wish to understand the Universe, think of energy, frequency, and vibration. ---Nikloa Tesla Water is conduit of Sound and Vibration. Water and Sound http://www.youtube.com/watch?v=uENITui5_jU&feat ure=youtu.be http://www.youtube.com/watch?v=naZr5kkAzYM Sound influences and moves water. Water is a conduit. Earth has its own frequency. Schumann Resonance 7.83 Hz Research is showing that being exposed to this frequency is absolutely integral to us. It controls our mental and physical health, it synchronizes our circadian rhythms, and it aids our immune system and improves our sense of well being. Not only are we surrounded by natural frequencies, our bodies are filled with them too. Our cells communicate using electromagnetic frequencies. Our brain emits a constant stream of frequencies and our DNA delivers instructions, using frequency waves. Sound—Frequency—Form God Spoke Genesis 1-31: 7 days of creation Sound as the Creator’s will Cymatics Hans Jenny 1960’s ability of sound to organize matter: http://www.youtube.com/watch?v=05Io6lop3mk&list =PLD9B543F27DC1C26C Metal Table: http://www.youtube.com/watch?v=AS67HA4YMCs David Icke—on building blocks of creation http://www.youtube.com/watch?v=3G5sV6DXQd0 Music of the Spheres Astronomers have recorded the sound of three stars that are similar to our Sun. The technique, dubbed stellar seismology. Using France's Corot space telescope. HD 49933, HD 18140 Music of the Stars and the Song of Our Sun http://www.youtube.com/watch?v=h7TfNrIBKGI http://www.youtube.com/watch?v=pGwDdTZBAEY http://www.youtube.com/watch?v=ANCC6MlG_kg Song of Earth and Planets Earth http://www.youtube.com/watch?v=_bnU6K1y468 Venus http://www.youtube.com/watch?v=lIZPpLbYPzU Mercury http://www.youtube.com/watch?v=894Aejo-R0U Pluto http://www.youtube.com/watch?v=4xpR4hyPSlE What Range Are We Hearing? Frequency is the number of pressure waves that pass by a reference point per unit time and is measured in Hertz (Hz) or cycles per second.
    [Show full text]
  • Amplified Sound Permit Registration Form
    AMPLIFIED SOUND PERMIT REGISTRATION FORM Applicant Information _______________________ Today’s Date _______________________________________________________________________________ Last Name First Name Business Name (if applicable) ___________________________________________________________ __________________________ Street City State Zip Code Contact Phone # ____________________________________________ Email Address Event Information Description of the event, the type of sound being used and sound equipment: _______________________ _______________________________________________________________________________________ _______________________________________________________________________________________ Event Location: ___________________________________________________________________ Date of Event: ______________________________ Hours of Event: _______________________________ Non-Commercial Band DJ Commercial Microphone Stereo Maximum Sound-Producing Power of Amplified Sound Equipment: Wattage to be used ________ Volume in Decibels of Sound Produced ________ Approximate Distance Sound will be Audible ________ Owner of Amplified Sound Equipment (indicate if same as applicant) _______________________________________________________________________________________ Last Name First Name Business Name ___________________________________________________________ ___________________________ Street City State Zip Code Contact Phone # Sound Truck/Vehicle Information (if applicable) * Year ___________ Make ______________ License Plate _______________________
    [Show full text]
  • Sound Insulation - Investigating Which Materials Are Good S Insulators Senior
    SOUND INSULATION - INVESTIGATING WHICH MATERIALS ARE GOOD S INSULATORS SENIOR Equipment: Activities 1 and 2: Variety of materials for testing (e.g. cotton wool, shredded paper, tissue, bubblewrap, polystyrene, plasticine, etc.), sound source (e.g. ticking clock, keyboard, buzzer), along with: Activity 1: plastic or polystyrene beakers Activity 2: box – shoebox or similar Suggested Class Level: Senior Preparation: Gathering of materials It would be helpful if the DPS Activities ‘Strange Sounds’ and ‘String Telephone’ had been carried out prior to this activity. Background Sound is a vibration – it needs something to pass on these vibrations (unlike light which can pass information: through a vacuum). Some materials allow sound pass through them very easily, especially hard rigid ones like metals. Other materials, especially soft ones like cotton wool, absorb sound. Ears are delicate and need to be looked after. They can easily be damaged in various ways: by very loud sounds especially if over a long time; by poking things in them; through old age or some disease. Most pop stars wear ear plugs. Trigger What was one of the main things that you noticed about the World questions: Cup in South Africa, apart from the football? (The sound of the vuvuzelas! These are plastic horns.) Some people may have enjoyed this sound, but can you think of any sounds that really annoy you? (Neighbours using electric drill in the night!...) How do you think you could block out loud sounds? (Put hands over ears, wear ear protection…) In what sort of jobs should people protect their ears? (People using power tools, miners using explosives, rock bands ..) Is it always good to block out all sound? (No, you cannot hear traffic or other possible dangers if you completely close off to the outside world).
    [Show full text]