FULL HEIGHT SOFT CLOSE LARDER 11 Adjust vertical door alignment with the 12 Adjust the vertical alignment of the door with the Alen 3 door bracket screws. screw located under the bottom runner. 300/400/500/600mm Assembly and fitting instructions IMPORTANT - The unit has a maximum loading limit of 100kg. Load should be evenly distributed across all trays with maximum load capacity for each tray not exceeding 16kg. No lubricant should be used on the runners. All fixings supplied MUST be used in the locations specified during installation. Wall For units 400mm wide and Unit must be securely above, two additional Additional fixed to the wall using a cabinet support legs legs suitable fixing bracket G should be fitted centrally. (not supplied). ‘Fine’ adjustment of the vertical alignment of the door can be achieved by compressing the stop cover and sliding towards PLEASE NOTE - Failure to use all supplied fittings according to instructions may void warranty. the front or rear. Handles must be mounted on the door in a central position in order to guarantee operation. WARNING! LARDER UNITS CAN BE HEAVY AND DANGEROUS. FAILURE TO CORRECTLY FOLLOW THESE INSTALLATION INSTRUCTIONS COULD LEAD TO PERSONAL INJURY.

A x6 M6 washer D x6 M6 x 12mm countersunk screw Parts F x1 Alen key 2.5mm Tools required B x30 3.5 x 16mm screw E x3 M5 x 12mm screw G x1 Alen key 4mm C x6 M6 x 12mm screw

Top runner x1 H x6 M5 Grub screw T (pre installed in frame) J

K Stop spring x1 Bottom runner x1 Now refer back to instruction No. 7 and check the Soft close L piston x1 distance is still 61mm front and back. If not, release Rubber stop x1 Y Runner fitting grub screws H and make the necessary adjustments. M U template x1

Top frame x1 Frame mounting V bracket x3 Adjust the horizontal and lateral door alignment Attach the frame basket clips to the frame and 13 14 Q Top basket collar x2 with screws on the door brackets. position the baskets. Attach basket locking clips to Door mounting secure baskets - snap fit connection. P N bracket x3 Stop cover x1

W Basket locking Q R Ring x2 X clip x12 Z W Bottom frame x1

R X Frame basket fixing clip x12 Basket x6

S Z Please ensure that all the above fittings are present before installation begins.

Align bottom template on centre line of cabinet base and secure with masking tape. B 1 Mark 7 screw fixing positions. B Z Remove template and screw bottom runner to cabinet base. B

B

Y T

IMPORTANT - The unit has a maximum loading limit of 100kg. Load should be evenly distributed across all baskets with maximum load capacity Issue date: 10.01.14 for each basket not exceeding 16kg. Issue date: 10.01.14 2 Align top template on centre line of cabinet top and secure using masking tape. Mark 5 screw fixing positions. 7 Insert top runner into top of frame. Remove template and screw top runner to cabinet top. Use grub screws on forward and rear frame uprights to adjust height to 61mm.

J 61mm

Y Views from below

61mm B

B Views from below B

H F All four grub screws Assemble frame and fit rubber stop and soft Compress stop spring and Fit stop cover below top must be securely 3 close piston into top channel. 4 insert into top channel. 5 channel ensuring stop tightened to ensure spring lugs ‘CLICK’ into the safe and effective operation of the L position. F H larder unit. K

M 8 Fit adjustment screws to 9 Fit door brackets to frame 10 Offer door to frame. Mark and fix Q P frame brackets and attach brackets. screws in two positions. H P frame brackets to frame Check door alignment before P upright. V marking and fixing the remaining screws.

U H Q R N

F H CLICK V IMPORTANT: When fitting components to the door ensure screws H U do not protrude R through inset panels H F

S For reliable and H safe performance V of the unit, all door fixing screws must be used. U 6 Attach frame to bottom runner. Lower onto runner and slide backwards. Align frame centrally and tighten the two grub screws.

S

IMPORTANT: Ensure G locating bars in bottom U section of frame locate T D A C V fully into clips in E bottom runner. D A C G B

Issue date: 10.01.14 Issue: 10.01.14