Installation Guide. 2010 Toyota Camry (Smart Key)
Total Page:16
File Type:pdf, Size:1020Kb
INSTALLATION GUIDE DB3 2010 Toyota Camry (Smart Key). 403.TL1 5.02 Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. Contents Introduction 4 Vehicle function compatibilities 4 Pre-installation and application warnings 5 OEM remote starter detection 4 Installation 6 Wiring diagram with T-Harness (TLTH1 & THTOD1) 6 Wiring diagram 7 Locating components in the vehicle 8 Vehicle connections 9 Connecting the module 11 Module programming 12 LED diagnostics and troubleshooting 13 Soft reset 15 Hard reset 15 Feature programming 16 Feature and option list 17 Limited one year consumer warranty 18 Quick reference guide 19 Warning! Safety first The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: • Never use a test light or logic probe when installing this unit. Always use a multimeter. • Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). • When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. • USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3 403.TL1 5.02 2010 Toyota Camry (Smart Key) © 2017-12-08 Directed. All rights reserved. Introduction DB3 is an all-in-one door lock and override module. Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to “Connecting the module” for more information. Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Auto Headlamp Shutoff Tach / RPM Output Arm Factory Security Entry Monitoring ALL Door Pins Disarm Factory Security Entry Monitoring Hood Pin Door Lock Control Entry Monitoring Trunk/Hatch Pin Door Unlock Factory Alarm Trigger Monitoring Driver Priority Unlock Brake Status (foot brake) Trunk / Hatch Release Door Locks Status Control of aftermarket alarm with OEM remote E-Brake Status Immobilizer Bypass-Data No Key Req'd Ignition Status Remote Start Ready SmartStart 4 403.TL1 5.02 2010 Toyota Camry (Smart Key) © 2017-12-08 Directed. All rights reserved. Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness Keys required for Keys required for compatible TLTH1/THTOD1 programming 1 operation 0 No takeover feature is available on Push-to-Start vehicles. The vehicle will shut down as soon as a door is opened. To remote start the engine, the hood, hatch, and all doors MUST be closed. Keyless and Smart Key will remain functional during remote start. The optional Plug & Play TLTH1/THTOD1 T-Harness is sold separately. The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed. All connectors are displayed from the wire side (unless specified otherwise). Refer to the "Vehicle connections" following the installation diagram. General notes: This section highlights important information for this specific firmware. [1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D [2] Connection required ONLY if Pit Stop/Idle mode is desired. [3] Autolights Interrupt ONLY required if vehicles are equipped with Autolights. OEM remote starter detection How to know if the vehicle is equipped with an OEM remote starter 1. An “ENGINE STARTER” 2. Remote start the OEM remote starter: sticker should be on the remote. Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds. Press & Hold x2 & for 3 seconds The parking lights flash after 3 seconds. The engine starts and the parking lights flash repeatedly for 20 seconds. ENGINE STARTER If the vehicle is equipped with an add-on Lexus/Toyota OEM remote starter The factory remote starter must be permanently disconnected before programming the Directed interface as both modules cannot coexist. See "Locating the OEM Remote Starter" below. Locating the OEM Remote Starter Vehicle OEM Remote Starter & Connector Location Toyota Camry (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel. Toyota Camry Hybrid (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel. Toyota Corolla (Smart Key) 2009-2013 Behind Glove Box & Passenger kick panel & Junction Box & Steering column. Toyota Highlander (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel. Toyota Highlander Hybrid (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel. Toyota Rav4 (Smart Key) 2009-2012 Behind Glove Box & Junction Box. 5 403.TL1 5.02 2010 Toyota Camry (Smart Key) © 2017-12-08 Directed. All rights reserved. Wiring diagram with T-Harness (TLTH1,THTOD1) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ). D2D only Main Body ECU (white conn. Dash Fuse Box under drivers dash) (white conn.) Headlight Switch 2 1 (white conn. at (+) 12V, 6 5 4 3 headlight switch) White/Black or White, pin 1 10 9 8 7 1 OR 10 9 8 7 6 5 4 3 2 1 (+) STSW: Pin 4 or 6 20 19 18 17 16 15 14 13 12 11 (-) AutoLights: (-) Parking Lights: Black or Lt. Blue, pin 18 Green or Yellow, pin 19 OBDII Diagnostic Connector 86 87 85 CUT 87a 30 (+) Start Stop Switch Output: Yellow PTS Switch TLTH1/THTOD1 (black conn. (optional T-Harness) Do not behind PTS button) connect D2D Port (-) Factory Alarm Re-arm ENGINE (-) Parking Light Output START 4 STOP 71 6 5 4 3 2 1 (+) 12V Input 14 13 12 11 10 9 8 (AC) Tach Input 14 (+) Ignition Input (-) Push-To-Start: 2 Blue or Pink, pin 7 (-) Ground (-) Push-to-Start Output: Green/Black:2 Do not connect any other accessory, ignition or starter wires from the remote starter to the vehicle. The interface module is handling the required vehicle power and start sequence. (AC) Tach Output: Violet/White: 5 10 12 (+) Ignition Status Output: Gray/Black:7 XKD2D65 6 403.TL1 5.02 2010 Toyota Camry (Smart Key) © 2017-12-08 Directed. All rights reserved. Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ). Main Body ECU Dash Fuse Box (white conn. (white conn.) under drivers dash) (+) 12V: White/Black or 2 1 White,pin 1 1 6 5 4 3 10 9 8 7 OR (+) STSW: Pin 4 or 6 HS CAN High: Pin 6 OBDII D2D Port Diagnostic 1 8 (+) 12V Input Connector 9 16 (AC) Tach Input HS CAN Low: White or Pink, pin 14 (+) Ignition Input (-) Parking Light Output HS CAN High: Tan/Black: 3 (-) Ground HS CAN Low: Tan: 4 4 Do not connect any other accessory, ignition or starter wires from the remote starter to the vehicle. The interface module (+) 12V Input: Brown: 7 is handling the required vehicle power and start sequence. 14 (+) Start Stop Switch Output: Yellow: 8 2 Autolights Interrupt (conn.