Buick 1995-Up Riviera
Total Page:16
File Type:pdf, Size:1020Kb
TUNERS / CASSETTE / DISC PLAYERS RADIO UPDATED EQ BUICK SINGLE THROUGH MINI STAN DIN ISO DIN DBL DIN STACK '96 CHASSIS H 13/ -2 2 2 2 37/ 3 '97 4 8 1995-UP RIVIERA CHASSIS W 71/ 71/ 71/ 7 71/ 71/ '98 8 8 8 8 8 '99 3 1 7 11 7 11 7 11 7 11 7 11 Coupe CHASSIS D 4 /4-5 /2 5 /8-6 /16 5 /8-6 /16 5 /8-6 /16 5 /8-6 /16 5 /8-6 /16 5 3 5 3 3 13 3 NOSE H 1 /8-1 /4 1 /8-1 /4 2 /8 1 /16 3 /4-4 1 3 1 3 1 11 11 1 NOSE W 4 /8-4 /16 4 /8-4 /16 7 /2 6 /16 6 /16-7 /4 1 3 1 SHAFT SP. 5 /8-5 /4 5 /8-6 IN DASH APPLICATION NOTES KS KS KS KS N KS APPLICATION KIT MODEL: GM 1500 SERIES HARNESS ADAPTOR: GM02 ANTENNA ADAPTOR: MDA-1 IN-DASH INSTALLATION AREA DIMENSIONS MAX DEPTH DEPTH WIDTH HEIGHT 3 3 3 3 CAVITY 7 /8" 7 /8" 8 /4" 5 /4" DASH 3 1 OPENING TYPE: M2000 7 /4" 3 /4" 1 DASH MATERIAL: PLASTIC THICKNESS: /8" FOR MAX DEPTH REMOVE REAR SUPPORT MODIFY CAVITY AMPLIFIER/EQ MOUNTING LOCATIONS (WxHxD) UNDER/IN UNDER GLOVE TRUNK/ DASH SEAT BOX CARGO 1 N/A - POWER SEAT 4 /2” X 7” X 12” Various Dimensions shown are inches. Vehicle illustration courtesy of For inch/mm conversions refer to chart section. NADA Used Car Guide. R U C C E C O E N Y T E A U R M L E O T F A S E H B R T A . A S H S E I C A C R L N A A E E U T S N S E I A R S M N D S O E I T C H N T N I E E R M S O U U F . C D E O E L D E B I Y T L S N L N A U O R F P A E S U R E G A R C T E O N B N O T T D O U E N B S N A D A B E C T . S I P C L M N I A E , U T E T N H A A C S M I S S O Y I C C H S T A 5 . R : B = BACK UP PLATES REQUIRED. K = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE E U E 1 D I T C = CUT TRIM/PLASTIC (STRUCTURE). KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER. C U O C C2 = CUT STEEL. KS = SCOSCHE KIT RECOMMENDED. N A G D = BELOW DECK ONLY. N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED. D1 = LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT). P = PERFECT WITHOUT MODIFICATION. D2 = CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK. P1 = MODIFY OR REMOVE POCKETS. D3 = NARROW SURFACE, BELOW DECK ONLY. P2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT). F1 = MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING. P3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT. F2 = MODIFY DASH CAVITY AND/OR PANEL. R = REAR LOAD ISOMOUNT. K = INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED. U = UNDERDASH. K1 = KIT MODIFICATIONS REQUIRED. W1 = WITH POWER WINDOWS ONLY. K2 = EXTENSION KIT RECOMMENDED. W2 = WITHOUT POWER WINDOWS ONLY. K3 = WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO. K4 = FABRICATE PANEL/BRACKETS. 35 © 1995-UP BUICK RIVIERA COUPE DASH WITH GM1503 KIT INSTALLED. REAR DECK 6 X 9” LOCATION (BOTTOM LOADED). PRELIMINARY: DISCONNECT THE NEGATIVE BATTERY CABLE. ANTENNA: THE FACTORY ANTENNA IS LOCATED ON THE RIGHT REAR FENDER. RADIO REMOVAL AND IN-DASH INSTALLATION: NOTE: THE FACTORY RADIO PROVISION IS FOR A M2000 CHASSIS RADIO. AN INSTALLATION KIT IS REQUIRED FOR ALL AFTERMARKET INSTAL- LATIONS. WE RECOMMEND THE USE OF A SCOSCHE GM1500 SERIES KIT. 1. GENTLY PULL OUTWARD ON LEFT AND RIGHT WINDSHIELD PILLAR PANELS TO RELEASE (2) SNAP CLIPS AND EXTRACT EACH ONE. 2. UNSNAP SIDE DASH PANELS AND REMOVE (1) 7 MM SCREW FROM BEHIND EACH. 3. EXTRACT (6) PLASTIC PUSH-PIN FASTENERS FROM UNDER FRONT EDGE OF UPPER DASH PAD. PULL OUTWARD TO REMOVE THE BOTTOM PANEL OF THE UPPER DASH PAD. 4. EXTRACT (5) 7 MM SCREWS SECURING UPPER DASH PAD, LIFT UP AND OUTWARD TO REMOVE PAD. 5. CAREFULLY PULL OUTWARD ON DASH/INSTRUMENT BEZEL TO RELEASE CLIPS, UNPLUG AND REMOVE BEZEL. 6. EXTRACT (3) 7 MM SCREWS FROM CLIMATE CONTROL MODULE, UNPLUG AND REMOVE MODULE. 7. EXTRACT (4) 7 MM SCREWS SECURING RADIO, UNPLUG CONNECTORS, FRONT DOOR 51/ ” AND TWEETER. ANTENNA LEAD, AND REMOVE RADIO. 4 FRONT DOOR SPEAKER INSTALLATION: 1 NOTE: THE FACTORY PROVISIONS ARE FOR A 5 /4” AND A 2" TWEETER DRIVER MOUNTED TO DOOR PANEL. 1. USING A PANEL REMOVAL CAREFULLY REMOVE PRY OUT ON SPEAKER GRILLE TO REMOVE. 2. EXTRACT (4) SCREWS HOLDING MID-RANGE DRIVER, UNPLUG AND REMOVE. 3. EXTRACT (4) SCREWS HOLDING TWEETER, UNPLUG AND REMOVE. REAR DECK SPEAKER INSTALLATION: NOTE: THE FACTORY PROVISIONS ARE FOR A 6” X 9” SPEAKER. DIRECT SPEAKER ACCESS FROM INSIDE TRUNK: 1. EXTRACT (2) 7 MM SCREWS FROM EACH SPEAKER, UNPLUG AND REMOVE SPEAKERS. FRONT DOOR PANEL. BATTERY LOCATION UNDER REAR SEAT BOTTOM. 36 © 1996 SCOSCHE INDUSTRIES, INC..