S PM051 INSTRUCTION MANUAL FOR

STAINLESS STEEL 44 Rem Mag; 454 Casull & 480 Ruger RUGER® Super Redhawk® DOUBLE-

– Rugged, Reliable Firearms® – READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM

© 2015 Sturm, Ruger & Co., Inc. This manual may not be reproduced in whole or in part without the express written permission of Sturm, Ruger & Co., Inc. For Service on This Model Please Call: (603) 865-2442 (See p. 26)

THIS INSTRUCTION MANUAL SHOULD ALWAYS ACCOMPANY THIS FIREARM AND BE TRANSFERRED WITH IT UPON CHANGE OF OWNERSHIP, OR WHEN THE FIREARM IS LOANED OR PRESENTED TO ANOTHER PERSON

www.ruger.com KY 4/15 C R18 State-By-State Warnings Certain states require by law that their own specified warning notices in larger-than-normal type be conspicuously included by the manufacturer, distributor or retailer with firearms sold in that state. Sturm, Ruger & Co., Inc. sells its products in compliance with applicable laws and regulations. Because our products may be sold in these states, we include the following: California: WARNING ADVERTENCIA “A los niños los atraen las armas “Children are attracted to and de fuego y las pueden hacer can operate firearms that can funcionar. Ellos pueden causarses cause severe injuries or death. lesions graves y la muerte. Evite Prevent child access by always que los niños tengan accesso a las keeping guns locked away and armas de fuego guardándolas unloaded when not in use. If you siempre con llave y descargadas keep a loaded firearm where a cuando no las esté utilizando. Si child obtains and improperly uses usted tiene un arma de fuego it, you may be fined or sent to cargada en un lugar en que un prison.” niño tiene acceso a ella y la usa indebidamente, le pueden dar una multa o enviarlo a la carcel.”

Connecticut: “UNLAWFUL STORAGE OF A LOADED FIREARM MAY RESULT IN IMPRISONMENT OR FINE.” Florida: “IT IS UNLAWFUL, AND PUNISHABLE BY IMPRISONMENT AND FINE, FOR ANY ADULT TO STORE OR LEAVE A FIREARM IN ANY PLACE WITHIN THE REACH OR EASY ACCESS OF A MINOR UNDER 18 YEARS OF AGE OR TO KNOWINGLY SELL OR OTHERWISE TRANSFER OWNERSHIP OR POSSESSION OF A FIREARM TO A MINOR OR A PERSON OF UNSOUND MIND.” 3 Maine: “ENDANGERING THE WELFARE OF A CHILD IS A CRIME. IF YOU LEAVE A FIREARM AND AMMUNITION WITHIN EASY ACCESS OF A CHILD, YOU MAY BE SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP FIREARMS AND AMMUNITION SEPARATE. KEEP FIREARMS AND AMMUNITION LOCKED UP. USE LOCKS.” Maryland: “WARNING: Children can operate firearms which may cause death or serious injury. It is a crime to store or leave a loaded firearm in any location where an individual knew or should have known that an unsupervised minor would gain access to the firearm. Store your firearm responsibly!” Massachusetts: “WARNING FROM THE MASSACHUSETTS ATTORNEY GENERAL: This handgun is not equipped with a device that fully blocks use by unauthorized users. More than 200,000 firearms like this one are stolen from their owners every year in the United States. In addition, there are more than a thousand suicides each year by younger children and teenagers who get access to firearms. Hundreds more die from accidental discharge. It is likely that many more children sustain serious wounds, or inflict such wounds accidentally on others. In order to limit the chance of such misuse, it is imperative that you keep this weapon locked in a secure place and take other steps necessary to limit the possibility of theft or accident. Failure to take reasonable preventive steps may result in innocent lives being lost, and in some circumstances may result in your liability for these deaths.” “IT IS UNLAWFUL TO STORE OR KEEP A FIREARM, RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACE UNLESS THAT WEAPON IS EQUIPPED WITH A TAMPER-RESISTANT DEVICE OR IS STORED OR KEPT IN A SECURELY LOCKED CONTAINER.” 4 New Jersey: “IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED FIREARM WITHIN EASY ACCESS OF A MINOR.” New York City: “THE USE OF A LOCKING DEVICE OR SAFETY LOCK IS ONLY ONE ASPECT OF RESPONSIBLE FIREARMS STORAGE. FOR INCREASED SAFETY, FIREARMS SHOULD BE STORED UNLOADED AND LOCKED IN A LOCATION THAT IS BOTH SEPARATE FROM THEIR AMMUNITION AND INACCESSIBLE TO CHILDREN AND OTHER UNAUTHORIZED PERSONS.” North Carolina: “IT IS UNLAWFUL TO STORE OR LEAVE A FIREARM THAT CAN BE DISCHARGED IN A MANNER THAT A REASONABLE PERSON SHOULD KNOW IS ACCESSIBLE TO A MINOR.” Texas: “IT IS UNLAWFUL TO STORE, TRANSPORT, OR ABANDON AN UNSECURED FIREARM IN A PLACE WHERE CHILDREN ARE LIKELY TO BE AND CAN OBTAIN ACCESS TO THE FIREARM.” Wisconsin: “IF YOU LEAVE A LOADED FIREARM WITHIN THE REACH OR EASY ACCESS OF A CHILD YOU MAY BE FINED OR IMPRISONED OR BOTH IF THE CHILD IMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITS THE FIREARM.” * * * * * * * * * * * * * * * * * * * * * * Please check with your licensed retailer or state police for additional warnings which may be required by local law or regulation. Such regulations change constantly, and local authorities are in the best position to advise you on such legal matters. 5 FIREARMS SAFETY IS YOUR RESPONSIBILITY SAFETY MUST BE THE FIRST AND CONSTANT CONSIDERATION OF EVERY PERSON WHO HANDLES FIREARMS AND AMMUNITION.

This Instruction Manual is designed to assist you in learning how to use and care for your RUGER® SUPER REDHAWK® properly. Please contact us if you have any questions. Only when you are certain you fully understand the Manual and can properly carry out its instructions should you practice loading, unloading, etc. with live ammunition. If you have any doubts about your ability to handle or use a particular type of gun safely, you should seek supervised instruction. Such personalized instruction often is available from local gun retailers, gun clubs or police departments. If none of these sources can help visit www.nra.org or write to the following address:

National Rifle Association 11250 Waples Mill Road Fairfax, VA 22030-7400 The person possessing a gun has a full-time job. You cannot guess; You cannot forget; You must know how to use your firearm safely. Do not use any firearm without having a complete understanding of its particular characteristics and safe use. Remember: There is no such thing as a foolproof gun.

6 TABLE OF CONTENTS Page State-By-State Warnings ...... 3 Nomenclature ...... 8 Locking Device Installation Instructions ...... 9 General Information and Mechanical Characteristics ...... 11 Ammunition ...... 12 Special Warning For Super Redhawk Alaskan ...... 13 Handling ...... 14 Dry-Firing ...... 14 To Load and Fire ...... 15 To Uncock (Decock) The Revolver ...... 17 To Unload or Eject Cases ...... 18 Disassembly ...... 20 Reassembly ...... 21 Care and Cleaning ...... 22 Storage ...... 23 Care of Stainless Steel Revolvers ...... 24 Attaching Ruger Scope Rings ...... 24 Sights ...... 25 Service and Parts Policy ...... 26 Shipping Firearms for Repair ...... 26 Ordering Parts ...... 27 Parts List ...... 28 Exploded View ...... 31 Super Redhawk Alaskan Component Parts List & Exploded View ...... 33 The Basic Rules of Safe Firearms Handling ...... 34 Warranty Information ...... 40

“Ruger,” “Redhawk” and the Sturm, Ruger logo are registered U.S. trademarks.

WARNINGS OF GREAT IMPORTANCE ARE FOUND ON THE FOLLOWING PAGES: Locking Devices 9 Firing 17 Alterations 11 Disassembly 19 Lead Exposure 12 Lubrication 22 Ammuniton 12 Storage 23 Recoil 13 Shipping 26 Handling 14 Parts Purchasers 27 Interlock 15 OTHER CAUTIONS AND WARNINGS APPEAR THROUGHOUT THE MANUAL.

7 NOMENCLATURE

Figure 1

FRONT SIGHT ADJUSTABLE REAR SIGHT FRAME BARREL HAMMER

CRANE LATCH

HAMMER PIVOT MUZZLE ASSEMBLY EJECTOR ROD

CYLINDER

TRIGGER GUARD TRIGGER GRIP SCREW GRIP PANEL

Figure 2

FRONT SIGHT HAMMER ASSEMBLY HAMMER PIVOT ASSEMBLY

HAMMER STRUT, MAINSPRING, & MAINSPRING SEAT GRIP SCREW

CYLINDER/CRANE ASSEMBLY

DISASSEMBLY PIN TRIGGER GUARD ASSEMBLY GRIP PANEL

8 WHY ARE WE INCLUDING A FIRED CARTRIDGE CASE WITH EVERY RUGER PISTOL AND REVOLVER? Certain states and jurisdictions require that all newly manufactured pistols and revolvers must be accompanied by a cartridge case, which has been test fired from that gun at the factory. The case must be placed in a sealed container bearing certain information concerning this test cartridge. At the time of retail sale in those jurisdictions, firearms dealers must forward such test cartridge to a designated destination such as their State Police Laboratory. Because independent distributors of Ruger® firearms have nationwide markets without territorial restrictions, we have decided to include a fired cartridge case with all new Ruger pistols and revolvers, to minimize the possibility of inadvertent non-compliance with these laws. Retail customers located in other states, where laws or regulations do not require the dealer to so act, may be assured that the fired cartridge case they receive with the firearm at the time of retail purchase is proof that your new Ruger firearm has undergone our normal test firing procedures during manufacture.

LOCKING DEVICE INSTALLATION INSTRUCTIONS

WARNING – USE OF LOCKING DEVICES

• Always keep your firearm pointed in a safe direction, including when you are installing or removing your locking device. • Always verify that your firearm is completely unloaded before installing your locking device. • Do not install locking devices in the trigger guard; always keep your fingers and locking device outside the trigger guard during device installation and removal. • Store firearms, ammunition and keys separately and securely, away from children and careless adults; do not store your firearm with the keys in the locking device. • Do not attempt to work the action of your firearm with the locking device in place; this may damage your firearm. • While locking devices are an important aid to security measures, they are not a substitute for safe firearm handling and proper storage. Remember that any Do not store keys mechanical device can be bypassed with enough time, in lock. knowledge, determination and equipment. LOCKING DEVICES MUST BE USED SAFELY AND RESPONSIBLY

9 Use the Correct Lock: While the basic locking device is substantially similar for all Ruger® firearms, due to the different shapes of the many Ruger® firearms, some firearms utilize different locking devices. The lock SUPER REDHAWK® with a 1-1/2” shackle is for use with Revolvers. It is very important to use the correct locking device!

To Install the Factory-Supplied Locking Device: 1. Keep the muzzle pointed in a safe direction and your fingers outside the trigger guard at all times! 2. Be sure the firearm and its cylinder are completely unloaded and contain no cartridges or cartridge cases! 3. Open the action completely. Swing out the cylinder. 4. Apply the locking device by placing the shackle of the lock onto your firearm as shown below. 5. Close the lock by pressing the shackle into the body of the lock (the part that receives the key) as tightly together as possible. The lock has bumpers and the shackle is coated with a non-marring material that will not harm the metal finish of your firearm; be careful not to dent the frame or grip panels of the revolver. 6. Once the lock is securely closed, remove the key. Pull firmly on the lock to test the connection and be sure it is locked. Do not leave or store your firearm with the key in the lock! Store your locked unloaded firearm and the key in secure, separate locations, away from ammunition, children, or unauthorized adults.

Correct Installation of Lock For Ruger® Super Redhawk® Revolvers Only

10 FIREARMS ARE DANGEROUS WEAPONS READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL THOROUGHLY AND CAREFULLY BEFORE USING. WARNING–ALTERATIONS

This product was designed to function properly in its original condition. Alterations can make it unsafe. Do not alter any part or add or substitute parts or accessories not made by Sturm, Ruger & Co., Inc.

DO NOT ALTER ANY GUN

GENERAL INFORMATION AND MECHANICAL CHARACTERISTICS The RUGER® SUPER REDHAWK® revolver is a double-action firearm which is specifically designed for hunting and target shooting with heavy Magnum cartridges and embodies many features found in the famous RUGER® REDHAWK® and GP100® revolvers. It is the second of an entirely new generation of Ruger double action revolvers. The unique frame extension permits the use of full wrap-around style grips of any desired configuration. This feature reduces overall weight and contributes to a desirable muzzle of heaviness. The crane and cylinder assembly of the Super Redhawk revolver locks directly into the frame, both at the rear of the cylinder and at the front of the crane. The ejector rod serves only as an ejector – it does not rotate with the cylinder. This mechanism is readily removable without tools and dismantles, along with the cylinder/crane group, into a small number of subassemblies for inspection and cleaning (see Figure 2, pg. 8). The internal parts are installed either through the top or bottom of the grip-frame; therefore, no side plate is needed. The resulting double solid frame contributes greatly to the extraordinary strength and reliability of these revolvers. The massive extended frame and use of Ruger integral scope mounting system on the wide top strap provide a solid scope mounting system. The RUGER® SUPER REDHAWK® revolver has a transfer bar which is connected directly to the trigger. The transfer bar safety system provides that the hammer blow can be transmitted to the firing pin only when the trigger is pulled all the way to the rear. This is a positive internal safety feature. Ruger® Super Redhawk® revolvers chambered for the .454 Casull and .480 Ruger cartridges have unfluted cylinders. Despite their many highly desirable features, Ruger® revolvers–as with all firearms–must at all times be handled with strict attention to correct safety practices, and be inspected frequently to assure the gun is working properly. 11 WARNING–LEAD EXPOSURE

Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to the State of California to cause birth defects, reproductive harm, and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure.

SHOOTING OR CLEANING GUNS MAY EXPOSE YOU TO LEAD

AMMUNITION RUGER® SUPER REDHAWK® revolvers in .44 Rem. Mag. will the .44 Rem. Mag. cartridge and the .44 S&W Spl. cartridge. revolvers chambered for the .454 Casull will chamber the .454 Casull and the .45 Colt cartridges. Revolvers chambered for the .480 Ruger cartridge should be used only with ammunition of that specific caliber. The correct caliber is marked on each revolver. Ruger revolvers are designed for use with cartridges of the correct caliber which are manufactured in accordance with the U.S. Industry Standards. Be certain to use proper cartridges of the correct caliber. See “Care and Cleaning,” p. 22, for important information on chamber cleaning.

WARNING–AMMUNITION

Death, serious injury, and damage can result from the use of wrong ammunition, bore obstructions, powder overloads or incorrect cartridge components. Always wear shooting glasses and hearing protection.

IMPROPER AMMUNITION DESTROYS GUNS

12 AMMUNITION (CARTRIDGES) NOTICE WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS THE RESULT OF, THE USE IN THE SUPER REDHAWK REVOLVER OF FAULTY OR NON-STANDARD OR “RE- MANUFACTURED” OR HAND LOADED (RELOADED) AMMUNITION OR OF CARTRIDGES OTHER THAN THOSE FOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.

SPECIAL SAFETY WARNING FOR SUPER REDHAWK ALASKAN WARNING–RECOIL

Ruger® Super Redhawk® revolvers are chambered for very powerful cartridges, as they are intended for hunting and protection against large potentially dangerous game. Because of this power, they necessarily develop heavy recoil when fired. Shooters should be prepared for this and always maintain a very firm, secure grip when firing. Failure by the shooter to control heavy recoil can result in property damage or severe personal injury if the revolver is permitted to recoil upwards or backwards in an uncontrolled manner. Minors and those who lack sufficient strength to control this heavy recoil should not be permitted to fire the revolver. HEAVY RECOIL CAN CAUSE SERIOUS INJURY IF UNCONTROLLED

13 HANDLING CARRYING: The Super Redhawk® revolver can be carried with all chambers loaded. When the hammer and trigger are fully forward, the transfer bar is lowered out of its firing position and the hammer rests directly on the frame.

WARNING–HANDLING

If the trigger is held to the rear, the gun can fire if the hammer strikes the transfer bar. Note that it need not be a deliberate effort to pull the trigger. Any situation where the trigger attains its rearward position and permits the transfer bar to be interposed between the hammer and the firing pin can cause the cartridge under the firing pin to discharge. NEVER DROP OR STRIKE THE REVOLVER – COCKED OR UNCOCKED. CARRY AND HANDLE THE REVOLVER IN SUCH A MANNER THAT THE HAMMER AND TRIGGER WILL NOT BE STRUCK. NEVER CARRY ANY REVOLVER WITH THE HAMMER COCKED OR THE TRIGGER HELD TO THE REAR

DRY-FIRING “Dry Firing” is practicing the trigger pull of the empty revolver for practice and familiarity. The Super Redhawk® revolver can be dry-fired without damage to the firing pin or internal components. Be sure that the revolver is unloaded before handling. Be sure of your bullet stop, even when dry-firing for practice. Do not dry-fire the revolver with the plastic ‘safety disc’ on the cylinder.

14 TO LOAD AND FIRE Be sure the revolver is pointed in a safe direction and is never cocked while loading.

1. Press the crane latch and guide cylinder out of frame to the left to its loading position (see Figure 3).

FIGURE 3 LOADING THE REVOLVER.

2. Insert cartridges and gently close cylinder, making sure it is securely latched. Do not “flip” the cylinder open or shut.

WARNING–CYLINDER INTERLOCK

When correctly operated, the cylinder cannot be opened when the hammer is cocked, and the hammer/trigger mechanism is not able to be operated until the cylinder is locked shut. However, this safety interlock can be

± intentionally defeated if the crane latch is depressed and the hammer is then cocked while the cylinder opened. If the cylinder is then shut when the hammer is cocked, the hammer may fall and the gun may fire. NEVER CLOSE OR OPEN THE CYLINDER WHILE THE HAMMER IS COCKED

15 3. The revolver is now ready to fire, either “double action” by pulling the trigger through its complete arc for each shot, or “single action” by cocking the hammer and then pulling the trigger for each shot. The trigger pull is somewhat shorter and lighter when the revolver is fired single action, and this is the preferred mode for precise shots or target shooting.

4. DO NOT TOUCH THE TRIGGER UNTIL YOU ARE READY TO FIRE.

CAUTION–DOUBLE ACTION FIRING

When firing in the double action mode, be sure that the trigger is released completely to its fully forward position before pulling the trigger for a subsequent shot. If the trigger finger is allowed to interfere with the full recovery of the trigger (preventing it from moving through about the last one-eighth inch of its forward movement), the trigger cannot be pulled again for another discharge. The trigger must be fully released after each shot is fired. This characteristic is found in all modern double action revolvers and “double action only” pistols.

FULLY RELEASE TRIGGER BETWEEN SHOTS

5. DO NOT HOLD THE REVOLVER BY THE BARREL OR CYLINDER WHEN FIRING.

16 WARNING–FIRING

When firing the Super Redhawk revolver, be sure all persons are a safe distance to the rear of the shooter. When fired, all revolvers discharge hot gas and particles of lead, powder grains, or lubricant through the clearance gap between the cylinder and the rear of the barrel at high speed. This can injure a person who is standing too close to the revolver. When firing the Super Redhawk revolver (or any revolver), always be certain that nothing – including your hands – is in the path of the hot gas and particles which are discharged from the front and sides of the cylinder. When shooting, adequate eye protection is essential. Shooters and bystanders must wear shooting glasses. Hearing protection must also be worn. Exposure to shooting noise can damage hearing. HOT GASES EXIT BARREL/CYLINDER GAP

TO UNCOCK (DECOCK) THE REVOLVER If your revolver is cocked, and you wish to let the hammer down to its forward position (against the frame), proceed as follows: USE EXTREME CARE WHEN ATTEMPTING TO DECOCK THE REVOLVER, AS THE THUMB SLIPPING DURING THIS PROCESS CAN RESULT IN AN ACCIDENTAL DISCHARGE IF THE TRIGGER IS HELD TO THE REAR. 1. Make certain that the revolver is pointed in a safe direction (see Rule 2, page 34). 2. Make certain both hands are dry and not impeded in any way due to gloves, bandages, cold, etc. 3. Grasp the revolver (if right handed) so that the thumb and forefinger of your left hand are firmly holding the frame, forward of the trigger guard. Thus, your left hand is in full control of the revolver (see Figure 4A, page 18). 4. Place your right thumb firmly on the hammer spur and, with your thumb securely in control of the hammer, squeeze the trigger only enough to permit the hammer to ‘break free’ of the trigger. At that instant, IMMEDIATELY RELEASE THE TRIGGER and then slowly permit the hammer, STILL SECURE UNDER YOUR THUMB, to move fully forward to its resting position against the frame. NOTE: It is imperative that finger pressure be removed from the trigger just as soon as it is free of the hammer. Then, properly, the trigger and hammer will move towards their fully forward rest positions together (see Figure 4B, page 18).

17 Practice this important gun handling skill with an unloaded revolver until you have developed the proper control and ‘touch’ to decock your revolver safely. The key to safe decocking is having the weight of the revolver controlled with one hand, while the thumb and forefinger of the ‘shooting hand’ control the hammer and trigger. Improperly restraining the trigger during this procedure may result in the hammer not resting fully against the frame. If this should occur, carefully repeat the procedure for decocking, steps 1–4 again.

UNCOCKING THE REVOLVER

A B 4 1

2 3

FIGURE 4 A. With the thumb controlling the hammer B. When hammer is free, IMMEDIATELY as shown (1), squeeze trigger to permit release trigger (3). Then lower hammer hammer to ‘break free’ (2). slowly to its resting position completely down against frame (4).

TO UNLOAD OR EJECT CARTRIDGE CASES

KEEP THE REVOLVER POINTED IN A SAFE DIRECTION! DO NOT ATTEMPT TO UNLOAD WHEN THE HAMMER IS COCKED. 1. Uncock the revolver (see pages 17 - 18). 2. Press crane latch. Guide cylinder out left of frame as for loading. The revolver now cannot be fired. 3. Push head of ejector rod smartly toward rear of cylinder until it stops. This action will extract cartridges or fired cases. Do not eject live cartridges onto any surface where a primer might strike a solid object and discharge the cartridge. 4. Check to be sure all chambers are empty.

18 NOTE: When ejecting fired cartridge cases, position the revolver at a high angle so the cases will come fully out of the chambers and not slip under the ejector. This high angle positioning is not necessary when ejecting unfired cartridges.

CORRECT UNLOADING SEQUENCE

WARNING–DISASSEMBLY

Always unload a firearm before cleaning, lubrication, disassembly or assembly. Never remove or install a loaded cylinder – it can fire if dropped or struck.

UNLOAD BEFORE CLEANING

19 DISASSEMBLY Read instructions before disassembling a gun.

An on-line video demonstrating the disassembly and reassembly of the double- action revolvers can be viewed by going to the “News & Resources” section, “Videos,” and then “Ruger Tech Tips” at www.ruger.com. 1. BE CERTAIN THE REVOLVER IS UNLOADED BEFORE DISASSEMBLY. 2. Using a properly fitting screwdriver, remove grip screw. Remove pistol grip inserts from grips. Grip panel locator may then be removed. Pull grip downward off frame. Take care not to lose the disassembly pin, which may fall free when the grip is removed (see Figure 5). 3. Cock the hammer. Insert disassembly pin Figure 5 about one half its length into the hole at the rear of the mainspring strut (see Figure 5). Lacking a disassembly pin, any similar instrument will serve. 4. With thumb on hammer spur, squeeze trigger allowing hammer to go fully forward. Lift out mainspring assembly. CAUTION: Do not remove the disassembly pin until the mainspring assembly is reinstalled in the revolver at the time of reassembly. Doing so will permit the mainspring to fly off its strut with great force and may cause injury. 5. Pull trigger and remove hammer pivot while holding trigger in a rearward position. Lift hammer out of the top of the frame while trigger is held in a rearward position (see Figure 6). Figure 6

6. Use mainspring assembly to depress trigger guard lock plunger located inside frame at rear of trigger guard. Simultaneously pull down and remove trigger guard assembly (see Figures 7 & 8).

Figure 7 Figure 8

20 NOTE: If you cannot supply sufficient force to the plunger using the mainspring assembly as a “tool,” then use a screwdriver of appropriate size and insert through hole in frame. It may be necessary to slightly depress the trigger while removing the trigger guard assembly. 7. Cradle the revolver frame in your left hand and with the thumb of your right hand press cylinder latch button, swing out cylinder assembly and remove it forward from the frame. 8. Further disassembly is not essential for normal cleaning purposes. Any further disassembly should only be undertaken by factory service personnel.

REASSEMBLY AGAIN, BE CERTAIN REVOLVER IS UNLOADED! Before starting reassembly, be certain that all components and the inside of the frame are thoroughly clean. In particular the tongue on the front of the trigger guard and its mating recess in the frame must be completely clean. 1. Replace cylinder and crane assembly in frame and close cylinder. 2. Hook front of trigger guard into recess in frame (see Figure 7). Align pawl in its recess in the frame and be sure transfer bar is in correct position in rear of firing pin. Swing trigger guard upward into position in frame then allow latch to re-engage. If solid resistance is felt when swinging trigger guard into frame, or if trigger guard will not lock into position re-check position of pawl and transfer bar (see Figure 9). Figure 9 NOTE: At this point in reassembly trigger should function to rotate and lock the cylinder. Pull the trigger a few times, to check proper functioning, as always with the revolver pointed in a safe direction. 3. Hold trigger in its rearward position and insert hammer into frame. Install hammer pivot. Release trigger and permit hammer to go fully forward. 4. With hammer forward, insert mainspring assembly into frame. Position the two ends of notch in the mainspring seat onto the matching projections of the grip frame. (Note: The large notch in the mainspring seat should be forward to allow clearance for the grip screw.) Hold mainspring assembly in position and cock hammer. It may be necessary to move the mainspring assembly a little to properly position the upper end of the mainspring strut to rest in recess in the hammer. When the hammer is cocked, disassembly pin can be removed (it will fall free). 5. Squeeze trigger and ease hammer down. Put the disassembly pin in its “nest.” Push grip upward onto the frame, install grip panel locator and place pistol inserts into position. Install and tighten grip panel screw. 6. Open and close cylinder. Function the trigger and hammer single action and double action to be certain that all parts are working properly. 21 CARE AND CLEANING ALWAYS BE CERTAIN THE REVOLVER IS UNLOADED BEFORE CLEANING. The internal mechanism of the Super Redhawk revolver can be lubricated without disassembly. A few drops of light oil recommended as suitable for firearms, applied periodically about the various frame openings, will work its way into the mechanism parts. The exterior of the revolver and the bore and chambers should be thoroughly cleaned and then wiped with an oily cloth if the gun is to be stored. Do not apply excess lubrication. An on-line video demonstrating the proper cleaning procedure of the double- action revolvers can be viewed by going to the “News & Resources” section, “Videos,” and then “Ruger Tech Tips” at www.ruger.com. To clean the revolver after firing, swing the cylinder out and clean the barrel from the muzzle by running a cleaning rod with a solvent coated patch through the bore several times. A bronze wire brush (of correct size for gun caliber) attached to the cleaning rod should then be pushed the full length of the bore several times. Again swab the bore with a solvent coated patch. Then wipe the rod clean and, using a dry patch, swab the bore until it is clean. Examine the bore to be sure that no fouling remains. Repeat the above procedure for each of the six chambers.

WARNING–LUBRICATION

Firing a revolver with oil, grease, or any other material even partially obstructing the bore may result in damage to the revolver and serious injury to the shooter and those nearby. Do not spray or apply lubricants directly on ammunition. If the powder charge of a cartridge is affected by the lubricant, it may not be ignited, but the energy from the primer may be sufficient to push the bullet into the bore where it may become lodged. Firing a subsequent bullet into the obstructed bore may damage the revolver and cause serious injury or death to the shooter and those nearby. Use lubricants properly. You are responsible for the proper care and maintenance of your firearms. IMPROPER LUBRICATION DESTROYS GUNS

22 Chambers must be thoroughly scrubbed to remove build-up of bullet metal and firing residue. A dirty chamber can prevent full seating of a cartridge, which in turn causes the cylinder to bind. DO NOT APPLY EXCESSIVE OIL TO UNDERSIDE OF EJECTOR – AREA SHOULD BE WIPED DRY WITH OILY CLOTH. Also, the underside of the ejector (‘star’) and the area of the cylinder where the ejector seats, must be clean. Dirt can prevent the ejector from fully seating. That condition can cause hard closing of the cylinder and interfere with proper cylinder rotation. If lead bullet loads are fired extensively, lead build-up may cause cylinder binding. Lubricate the cylinder crane gap with Break-Free® CLP or some other lubrication which meets mil. spec. Mil-1-63460 to prevent this condition.

STORAGE GUNS SHOULD NOT BE STORED LOADED! USE THE LOCKING DEVICE SUPPLIED WITH THE REVOLVER TO RENDER IT INOPERATIVE FOR SAFE STORAGE. (SEE PAGE 9)

Do not keep the revolver in a leather, fabric or canvas holster when it is stored. These materials attract moisture, even though the holster may appear to be perfectly dry.

WARNING–STORAGE

• Never place or store any firearm in such a manner that it may be dislodged. Firearms should always be stored securely and unloaded, away from children and careless adults. • Use the locking device supplied with the revolver for storage. The use of a locking device or safety lock is only one aspect of responsible firearms storage. • For increased safety, firearms should LOADED be stored unloaded in a location that is both separate from their ammunition and inaccessible to children and any other unauthorized person.

STORE SECURELY & UNLOADED

23 CARE OF STAINLESS STEEL REVOLVERS Revolvers made of stainless steel are more resistant to corrosion than blued steel revolvers. However, in the interest of proper operation and long life of your revolver, inspect it frequently and clean, lubricate and apply an appropriate rust preventative. Sometimes surface discoloration may be noted, particularly in the grip area of stainless steel revolvers, resulting from perspiration. Contact with some types of holsters can also cause stains or rusting. Rusting may also occur as a result of the revolver being exposed to moisture, humidity, salt air or chemicals. Minor discoloration can usually be removed by rubbing the stained area with an abrasive ink eraser, crocus cloth, or a “metal polishing” compound. When using any of these abrasives, proceed with care and use light pressure to achieve a blending of ‘color’ with those areas that are not discolored. External surfaces of the barrel, frame and cylinder should be cleaned and wiped dry after use or after exposure to adverse conditions. If the revolver is to be stored, coat it with a light film of oil or preservative. Where the revolver is in continuing use, and the presence of oil or grease would be objectionable, then the external surfaces can be coated (after cleaning and drying) with a paste wax formulated for use on metals. Apply the wax sparingly, allow time for it to dry hard, then buff lightly with a soft cloth. When applying the wax, take care that it does not get into the mechanism or on the functioning parts such as the hammer, trigger, crane latch, etc. A properly applied hard wax coating will not interfere with gun handling, and it will provide a measure of protection.

ATTACHING RUGER SCOPE RINGS Each Ruger scope ring is a mated assembly of a top and a base. Do not mix the parts of the two ring assemblies as they are not interchangeable. On the underside of each mounting ring assembly there is an integral lug, located off center with respect to the front and back sides of the mount. The lug is nearer to the front surface. By reference to the lug, the mounting ring can be correctly assembled with the front of the ring toward the muzzle of the revolver. 1. Disassemble one ring and reassemble over the scope body between the turret and the eyepiece. (Note: High ring goes on front mount. Low ring on rear mount.) 2. Install the four top screws. Do not tighten. 3. Disassemble the other ring and install it on the forward section of the scope tube with the lug forwardly also. Install the four top screws. Again, do not tighten. 4. Assemble the rings to the frame with the lugs engaging the recesses in the top surface of the receiver. Tighten the clamp nuts so that the rings are locked to the semi-circular cuts on the sides of the frame. 5. Rotate the scope until cross-hairs are aligned properly, and slide the scope to desired eye relief. Then tighten the eight top screws each a bit at a time to grip the scope body. 6. Sight in according to the directions with your scope. 24 SIGHTS The Super Redhawk revolver is provided with an insert front sight. To change the front sight, depress the spring-loaded plunger in the front of the barrel rib with a small punch and lift rear of sight blade. The adjustable rear sight has a white outline blade. Each click of the rear sight adjustment screws (either windage or elevation) will move the point of impact of the bullet approximately 3/4” at a distance of 25 yards. Move the rear sight in the direction you desire the bullet to move on the target. The suggested sight picture is shown below. See “Attaching Ruger Scope Rings,” p. 24.

ELEVATION WINDAGE

RIGHT UP DOWN

LEFT

To raise point of impact: turn screw To move the point of impact to the right: counterclockwise. turn screw counterclockwise. To lower point of impact: turn screw To move the point of impact to the left: clockwise. turn screw clockwise.

SUGGESTED SIGHT PICTURE

Top of front sight even with top of rear sight blade. Front sight centered in notch of rear sight blade. Target bull’s-eye centered on top of front sight.

25 SERVICE AND PARTS POLICY If you have any questions with regard to the performance of your RUGER® SUPER REDHAWK® revolver, please write or call (603-865-2442) our Newport, New Hampshire Customer Service Department, fully describing all circumstances and conditions involved. If you should return your revolver to the factory for repair, or order parts for it, please comply with the following suggestions for prompt service:

WARNING: BEFORE SHIPPING ANY FIREARM, BE ABSOLUTELY CERTAIN THAT IT IS UNLOADED. DO NOT SHIP CARTRIDGES WITH A FIREARM. SHIPPING FIREARMS FOR REPAIR RUGER® SUPER REDHAWK® revolvers returned to the factory for repair should be sent to: Ruger, Customer Service Department, 411 Sunapee St., Newport, New Hampshire 03773. NOTE: You must obtain a Repair Authorization Number before returning your firearm. An authorization number can be obtained by contacting Customer Service online at www.ruger.com or calling the Customer Service Dept. at 603-865-2442. Guns should be sent prepaid. We will not accept collect shipments. The Federal Gun Control Act, as well as the laws of most states and localities, do not prohibit an individual (who is not otherwise barred from purchasing or possessing a firearm) from shipping a firearm directly to the manufacturer for repair. However, before you ship your revolver to us, be certain that your state or locality does not have a law or regulation which will prohibit you from receiving the revolver from us after it has been repaired. If such receiving is prohibited, then please have a Federally Licensed firearms dealer ship the gun to us. If your revolver is sent to us by a dealer, it will be returned to that dealer after being repaired. If a handgun (pistol or revolver) is shipped by an individual who does not hold a Federal Firearms License, it must be shipped for overnight delivery via U.P.S., Federal Express or other, similar private overnight service. NOTE: Handguns may not be shipped via U.S. Mail. Persons who do not hold a Federal Firearms License are prohibited by Federal law from shipping a handgun by Mail. Handguns mailed in violation of the law are impounded by the Post Office. DO NOT SEND GUN BOXES OR LITERATURE THAT YOU CONSIDER TO BE COLLECTOR’S ITEMS – THESE ARE INVARIABLY DAMAGED OR DESTROYED IN SHIPMENT. Please do not include holster, grip panels, or other accessories with a firearm being shipped to the factory for service. Rifles and shotguns may be shipped via U.S. Mail. Always insure your shipment. Enclose a letter which includes your name, address, telephone number, serial number, model of the firearm, and your repair authorization number. Describe in detail the trouble you have experienced with your firearm, or the work you wish to have done. Merely stating that the firearm “needs repair” is inadequate information. State precisely what is wrong. Please enclose copies of any previous correspondence. All work performed is subject to a minimum labor charge and charges for shipping and handling. Most models can be reblued, but custom gunsmithing service or nonstandard alterations are NOT AVAILABLE from Ruger Customer Service Departments. Please contact the Customer Service Department for pricing information. 26 WARNING–PARTS PURCHASERS

• It is the purchaser’s responsibility to be absolutely certain that any parts ordered from the factory are correctly fitted and installed. • Firearms are complicated mechanisms and IMPROPER FITTING OF PARTS MAY RESULT IN A DANGEROUS MALFUNCTION, DAMAGE TO THE FIREARM, AND SERIOUS INJURY TO THE SHOOTER AND OTHER PERSONS. • The purchaser and installer of parts must accept full responsibility for the correct adjustment and functioning of the firearm after such installation. PARTS MUST FIT CORRECTLY

ORDERING PARTS Please contact the New Hampshire Customer Service Department for parts availability and current prices. All parts orders for the RUGER® SUPER REDHAWK® revolvers should be sent to : Ruger, Customer Service Department, 411 Sunapee Street, Newport, New Hampshire, 03773, 603-865-2442. We cannot comply with open account or C.O.D. orders. Payment in full via credit card (Visa or MasterCard only), money order or certified bank check (no personal checks or cash, please) is required before any service will be performed. Please provide your credit card number, your name as it appears on the credit card, the expiration date, and the 3-digit security code. All parts orders are subject to a minimum charge and charges for shipping and handling. Order parts by Part Name and Part Number and include the entire serial number of the firearm for which the parts are being ordered. There is a minimum labor charge plus a shipping and handling charge if the parts are factory fitted. All factory fitted parts are fit on an exchange basis only. We will not return the replaced parts. Please contact the Customer Service Department for pricing information. Barrels, cylinders, cylinder/crane assemblies and a number of other component parts must be fitted at the factory. Company policy is to proof-test and/or function fire all barrels after fitting to the receivers in which they are to be used. This procedure ensures maximum protection to our customers. The special proof-test ammunition used in this testing is sold only to bonafide firearms manufacturers and is not available to gun shops, gunsmiths or individuals. Because it is a serial numbered part, the frame of the RUGER® SUPER REDHAWK® revolver is defined as a ‘firearm’ by Federal Law and is not offered for sale as a component part. Parts designated by an asterisk (*) must be factory fitted. These parts are fitted on an exchange basis only. We will not return the replaced parts. We will not return any part that is broken, malfunctioning, badly worn or has been modified. See “Warning – Parts Purchasers” above.

WARNING: A gun containing broken, malfunctioning or badly worn parts should not be fired. 27 RUGER® SUPER REDHAWK® PARTS LIST Design, prices and specifications subject to change without notice. SPECIFY MODEL AND CALIBER WHEN ORDERING (See Exploded View on Page 31.)

Key Part Name Part No. Model *1 Hammer Assembly KY04000 All Models 2 Hammer Pivot Pin Assembly KE-16B All Models 3 Hammer Dog Spring KE-57 All Models 4 Hammer Dog Plunger KH05100 All Models *5 Hammer Dog KH01900 All Models 6 Hammer Dog Pivot Pin KE-22 All Models 7 Hammer Strut KT01500 All Models 8 Hammer Strut Mainspring KW00401 44 Magnum Hammer Strut Mainspring KY00400 454 Casull & 480 Ruger 9 Hammer Strut Seat KT00500 All Models *10 Trigger Assembly KY03911 All Models 11 Trigger Plunger KH03200 All Models 12 Pawl Plunger Spring KH05000 All Models 13 Pawl Plunger KH05100 All Models 14 Pawl KH00700 All Models 15 Trigger Link KT07100 All Models 16 Trigger Link Pin KH06400 All Models 17 Transfer Bar KH01700 All Models *18 Trigger Guard KT00300A All Models *19 Crane Pivot Lock Plunger KH06700 All Models *20 Crane Pivot Lock Spring KH07600 All Models 21 Cylinder Latch Pivot KH01400 All Models 22 Cylinder Latch Spring KH05000 44 Magnum Cylinder Latch Spring KY05000 454 Casull & 480 Ruger 23 Cylinder Latch Plunger KE-51 All Models 24 Trigger Pivot Pin KE02800 All Models 25 Trigger Link Plunger KT03700 All Models 26 Trigger Guard Latch Spring KT03800 44 Magnum Trigger Guard Latch Spring KY03801 454 Casull & 480 Ruger 27 Trigger Guard Latch KT04600 All Models 28 Trigger Guard Latch Pin KE-22 All Models 29 Cylinder Latch KH04505 All Models *30 Ejector Retainer KH02400 All Models 31 Ejector Spring KE-25 All Models 32 Center Pin Spring KE-34 All Models 33 Center Pin Rod KH05400 All Models

* Parts so marked must be factory fitted.

28 Key Part Name Part No. Model 34 Center Pin KE-53 All Models *35 Cylinder Assembly KH00100D 44 Magnum Cylinder Assembly, Non-Fluted KY00105D 454 Casull Cylinder Assembly, Non-Fluted KY00107D 480 Ruger *36 Ejector KH01800 44 Magnum Ejector KY01801 454 Casull Ejector KY01803 480 Ruger *37 Crane & Crane Pivot Assembly KH00803 All Models *38 Cylinder Retaining Ball, 2 Req’d KE03000 All Models 39 Front Latch KH03100 All Models 40 Front Latch Pivot Pin KH05600 All Models 41 Front Latch Pivot Lock Spring KH07700 All Models 42 Front Latch Pivot Lock KH07500 All Models 43 Front Latch Spring KE-57 All Models 44 Front Latch Spring Plunger KH06800 All Models 45 Ejector Rod KH02300 All Models *46 Recoil Plate KMR02000 All Models 47 Firing Pin Rebound Spring KE-48 All Models *48 Firing Pin KT02100 All Models 49 Crane Latch Spring KE-57 All Models 50 Crane Latch Plunger KH05100 All Models *51 Crane Latch KT00909 All Models *52 Crane Latch Pivot KE-27 All Models 53 Recoil Plate Cross Pin KH04900 All Models *54 Barrel, 7 1/2” KY00616 44 Magnum Barrel, 9 1/2” KY00617 44 Magnum Barrel, 7 1/2” KY00618 454 Casull Barrel, 7 1/2” KY00620 480 Ruger 55 Front Sight, Y03612 44 Mag & 454 Casull .533” Ramp w/Red Insert (except Alaskan) Front Sight, Y03614 480 Ruger .610” Ramp w/Red Insert 56 Front Sight Screws, 3 Req’d XR07601 All Models 57 Rear Sight Assembly H05900C 44 Magnum Rear Sight Assembly H05900D 454 Casull & 480 Ruger Includes Key Nos. 58 - 64 58 Rear Sight Elevation Spring, MR05906 All Models 2 Req’d 59 Rear Sight Base MR15905 All Models 60 Rear Sight Pivot Pin KMR05600 All Models 61 Rear Sight Elevation Screw MR05902 All Models 62 Rear Sight Windage Spring MR05907 All Models 63 Rear Sight Blade, High H07203A 44 Magnum Rear Sight Blade, Low E05904A-A 454 Casull & 480 Ruger 64 Rear Sight Windage E05903 All Models Adjustment Screw

* Parts so marked must be factory fitted. 29 Key Part Name Part No. Model 65 Hogue® Rubber Monogrip T01024 All Models Includes Key Nos. 65a - 65c 65a Grip Pin All Models 65b Grip Saddle All Models 65c Grip Screw All Models 66 Scope Ring Assembly, Low KD71L All Models Includes Key Nos. 66a - 66c 66a Scope Ring Clamp D-74M All Models 66b Scope Ring Nut D-73M All Models 66c Torx® Head Screws, 8 Req’d KMPF07602M All Models Torx® Key Wrench, MPF07601 All Models Not Illustrated (for Torx® Head Screw) Disassembly Pin, E-63 All Models Not Illustrated

30 ® EXPLODED VIEW SUPER REDHAWK

31 ® SUPER REDHAWK REVOLVER MECHANISM

32 SUPER REDHAWK® ALASKAN™ COMPONENT PARTS LIST (See Exploded View on Page 31 of Instruction Manual for Other Parts)

Key No. Part Name Part No. 1 Frame/Barrel Assembly KY20609 2 Front Sight Y03610 *3 Trigger Guard KY00301 *4 Trigger KY03901 5 Front Sight Cross Pin KY05600 6 One Piece Rubber Hogue® Grip T01023 (Includes Key Nos. 6a, 6b & 6c) 6a Grip Pin 6b Grip Saddle 6c Grip Screw

* PARTS SO MARKED MUST BE FACTORY FITTED

33 THE BASIC RULES OF SAFE FIREARMS HANDLING We believe that Americans have a right to purchase and use firearms for lawful purposes. The private ownership of firearms in America is traditional, but that ownership imposes the responsibility on the gun owner to use his firearms in a way which will ensure his own safety and that of others. When firearms are used in a safe and responsible manner, they are a great source of pleasure and satisfaction, and represent a fundamental part of our personal liberty. Firearms do not cause accidents! Firearms accidents are almost always found to have been the result of carelessness or ignorance on the part of the shooter of the basic rules of safe gun handling. The following rules must be observed by gun users at all times. Safe gun handling is not just desirable, it is absolutely essential to your safety, the safety of others, and the continuation of gun ownership and sport shooting as we know it today.

1. LEARN THE MECHANICAL AND HANDLING CHARACTERISTICS OF THE FIREARM YOU ARE USING. Not all firearms are the same. The method of carrying and handling firearms varies in accordance with the mechanical provisions for avoiding accidental discharge and the various proper procedures for loading and unloading. No ® person should handle any firearm without RUGER first having thoroughly familiarized INSTRUCTION MANUAL READ THE INSTRUCTIONS himself with the particular type of firearm AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE he is using, and with safe gun handling in USING THIS FIREARM. general.

2. ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. Be sure of the bullet stop behind your target, even when dry-firing. Never let the muzzle of a firearm point at any part of your body or at another person. This is particularly important when loading or unloading a firearm. In the event of an accidental discharge, no injury can occur as long as the muzzle is pointing in a safe direction. A safe direction means a direction that will not permit a discharged bullet to strike a person, or to strike an object from which the bullet may ricochet. 34 A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor, window, etc., and strike a person or damage property. Make it a habit to know exactly where the muzzle of your gun is pointing whenever you handle it, and be sure that you are always in control of the direction in which the muzzle is pointing, even if you fall or stumble. Keep your finger off the trigger until you are ready to shoot.

3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN USE. Firearms should be loaded only when you are in the field or on the target range or shooting area, ready to shoot. Firearms and ammunition should be securely locked in safes, racks or cabinets, or by using the locking device supplied with the firearm, when not in use. Ammunition should safely be stored separate from firearms. Store your firearms out of sight of visitors and children. It is the gun owner’s responsibility to be certain that children and persons unfamiliar with firearms cannot gain access to firearms, ammunition, or components. 4. BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONS BEFORE SHOOTING. Even a bit of mud, snow or excess lubricating oil or grease in the bore may cause the barrel to bulge, or even burst on firing, and can cause serious injury to the shooter and bystanders. Be sure that you are using ammunition of the proper caliber and loading for the gun you are using. If the report or recoil on firing seems weak, or doesn’t seem quite right, CEASE FIRING IMMEDIATELY, unload your firearm, and check to be sure that no obstruction has become lodged in the barrel. 35 5. BE SURE OF YOUR TARGET BEFORE YOU SHOOT. Don’t shoot unless you know exactly where your bullet is going to strike. Be sure of the bullet stop behind your target, even when dry-firing with an unloaded gun. If you are in the field hunting, do not fire at a movement or noise. Take the time to be absolutely certain of your target before you pull the trigger.

6. WEAR SHOOTING GLASSES AND HEARING PROTECTION WHEN YOU SHOOT. All shooters should wear protective shooting glasses and adequate hearing protection when shooting. Exposure to shooting noise can damage hearing, and wearing adequate eye protection when shooting is essential.

7. NEVER CLIMB A TREE OR FENCE WITH A LOADED FIREARM. Put the firearm down carefully before climbing a fence, and unload it before climbing or descending a tree or jumping over a ditch or other obstruction. Never pull or push a loaded firearm toward yourself or another person. When in doubt, or whenever you are about to do anything awkward, unload your gun!

36 8. DON’T SHOOT AT A HARD SURFACE OR AT WATER. Bullets can glance off many surfaces like rocks or the surface of water and travel in unpredictable directions with considerable velocity.

9. NEVER TRANSPORT A LOADED FIREARM. Firearms should always be unloaded before being placed in a vehicle. A suitable carrying case or scabbard should by used to carry an unloaded firearm to and from the shooting area.

10. AVOID ALCOHOLIC BEVERAGES WHEN SHOOTING. Don’t drink until the day’s shooting is over. Handling firearms while under the influence of alcohol in any form, or medications that could affect your judgment or coordination, constitutes a criminal disregard for the safety of others.

37 A BRIEF ACCOUNT OF AN EXTRAORDINARY ACHIEVEMENT: RUGER® FIREARMS Sturm, Ruger & Company, Inc., had its beginning in a small machine shop occupying a rented frame building in Southport, Connecticut. In January, 1949, with an initial investment of only $50,000 and an idea, William B. Ruger and Alexander M. Sturm started production of a .22 caliber autoloading pistol–a design which was so successful that it became the cornerstone upon which one of the most comprehensive lines of sporting firearms ever made in America was established. After Alex Sturm’s death in 1951, William B. Ruger continued to direct the Company until his death in 2002. William B. Ruger, Jr. continued to provide guidance, which helped make this Company a sound and successful enterprise, until his retirement in 2006. The Company has continued to prosper, under new management and guidance from our Board, with new products and fresh perspectives. Ruger, in this relatively short time, has established itself as a leading small arms design organization, developing a unique and broad line of fine quality sporting, military and police firearms to become one of the world’s most famous producers of revolvers, pistols, rifles and shotguns. Since 1949, Ruger craftsmen have built many millions of firearms. During its five decades of growth and progress under the leadership of William B. Ruger, the Company developed a business philosophy and implemented policies which represent a constructive influence in the life of modern America. From the beginning, Ruger played a positive role in conservation efforts and has supported the interests of shooters through such groups as the National Rifle Association, National Shooting Sports Foundation, and many regional sportsmen’s organizations. The Company has always endeavored to market its firearms for constructive and recreational purposes, to emphasize the traditional and responsible aspects of shooting, to render meaningful public services, and to encourage shooters in constructive, responsible, and safe participation in the shooting sports. Its motto, “Arms Makers For Responsible Citizens®,” exemplifies this Company philosophy. Today, Ruger® is particularly mindful of those elements which have contributed to the creation of its success, and extends heartfelt thanks to its many loyal employees and customers.

The firearms catalog, and instruction manuals for all Ruger® firearms, can be downloaded from our website at: www.ruger.com

38 NOTES

39 WHY NO WARRANTY CARD HAS BEEN PACKED WITH THIS NEW RUGER® FIREARM The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty. It does provide that if a written warranty is given, it must be designated as “limited” or as “full” and sets minimum standards for a “full” warranty. Sturm, Ruger & Company, Inc. has elected not to provide any written warranty, either “limited” or “full”, rather than to attempt to comply with the provisions of the Magnuson-Moss Act and the regulations issued thereunder. There are certain implied warranties under state law with respect to sales of consumer goods. As the extent and interpretation of these implied warranties varies from state to state, you should refer to your state statutes. Sturm, Ruger & Company wishes to assure its customers of its continued interest in providing service to owners of Ruger® firearms.

STURM, RUGER & Company, Inc. 411 Sunapee Street Newport, New Hampshire 03773 U.S.A. www.ruger.com Arms Makers For Responsible Citizens® A COPY OF THE INSTRUCTION MANUAL FOR ANY RUGER® FIREARM IS AVAILABLE FROM THE FACTORY FREE ON REQUEST, OR IT MAY BE DOWNLOADED FROM OUR WEBSITE AT WWW.RUGER.COM. THESE INSTRUCTION MANUALS CONTAIN IMPORTANT WARNINGS WHICH MUST BE UNDERSTOOD BEFORE USING THESE FIREARMS.

The Following are Sturm, Ruger & Co., Inc. Trademarks: “BX-Trigger,” “Bisley,” Eagle “SR,” “Elite 452,” “Gold Label,” “It’s Mine and It’s American,” “LC6,” “LCR-357,” “LCRx,” “Mark II,” “Mark III,” “Match Champion,” “Model 96,” “P345D,” “P345PR,” “P85,” “P90,” “P91,” “P93,” “P94,” “P95,” “P97,” “Ruger Marksman Adjustable,” “Ruger 77/50,” “Ruger 10/17,” “77/357,” “Single-Seven,” “SR45,” “SR-556C,” “SR- 556VT,” “SR-762,” “10/22-FS,” “22 Charger,” “22/45,” and “22/45 RP.” The Following are Registered U.S. Trademarks Belonging to Sturm, Ruger & Co., Inc.: “RUGER,” Sturm,Ruger Logo,” “AC-556,” “AR-556,” “Arms Makers For Responsible Citizens,” “All-Weather,” “Bearcat,” “Blackhawk,” “BX-15,” “BX-25,” Eagle “R,” “GP100,” Hard “R” Logo, “Hawkeye,” “LC380,” “LC9,” “LC9s,” “LCP,” “LCR,” “M77,” “Mini Thirty,” “Mini-14,” “9E,” “Old Army,” “Power Bedding,” “P345,” “Redhawk,” “,” “,” “Ruger Hunting,” “Ruger Hunting” Logo, “Ruger Inside & Out” phrase & logo design, “Ruger 77/17,” “Ruger 77/22,” “Ruger 77/44,” “Ruger SP101,” “Ruger 10/22 Takedown” phrase & logo design, “Ruger Titanium,” “Ruger 22/45 Lite,” “,” “Rugged, Reliable Firearms,” “Security-Six,” “Service-Six,” “Single-Nine,” “Single-Six,” “Single-Ten,” “Speed-Six,” the “SR” Design, “SR9,” “SR9c,” “SR40,” “SR40c,” “SR-22,” “SR22,” “SR-556,” “SR-556E,” “SR1911,” “Super Redhawk Alaskan,” “Target Grey,” “10/22,” and “10/22 Takedown.”