DOCSLIB.ORG

Woodstain Filler

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Woodstain Filler TDS0120 Established: 25 Feb 2013 Updated: 07 Mar 2017 TECHNICAL DATA SHEET FOR WOODSTAIN FILLER DESCRIPTION : WoodStain Filler is a semi-transparent, pigment-based gel stain. It gives colour to wood surface and enhances the beauty of wood grains TYPE : Woodstain filler based on urethane modified long oil alkyd COLOUR : Two colors (BurmeseTeak & Mahogany) USES : Ideal for the decoration and protection of interior wood surfaces such as wooden furniture, door, window frames, cabinet, molding and paneling FEATURES : Fade resistance Easy to stir and non-settling Non-grain raising No drips, runs or spills APPLICATION DATA METHOD : Cloth or sponge Rub WoodStain Filler in circular motion with lint-free cloth or sponge. Spread as far as possible to fill in the wood pore evenly THEORETICAL COVERAGE : 18 – 23 m² per litre (actual coverage is dependent on substrate condition) DILUTION : Ready for use after thorough stirring If necessary, dilute with 1 – 2% Bodelac 9000 GP Reducer or Mineral Turpentine to improve ease of application SURFACE PREPARATION : New or unpainted wood surfaces: Surface must be clean, dry and free from grease, paint, wax, dirt and other contaminants before painting Clean off mould, algae, lichen and moss with a wire brush Smooth bare wood surface to be painted using grade #60 or #80 sandpaper, working in the direction of the grain before dusting off If necessary, fill the wood grains with appropriate filler and smooth with sandpaper (grade #150 or #180) Wood must be relatively dry, moisture content should not exceed 12 % before painting Allow the paint to dry thoroughly before applying next coat Should fibre be observed, dry sand lightly before subsequent coat Page 1 of 3 TECHNICAL DATA SHEET FOR WOODSTAIN FILLER Previously Painted Wood Surfaces : If the previous paint film is in sound condition and without wax, smoothen it with sandpaper. Clean off and dry For old paint which is in sound condition and without wax, smoothen it with sandpaper. Clean off and dry Otherwise, remove all unstable paint film, dust, oil, wax and other foreign matters Particular care is necessary on previously waxed surfaces and thorough mechanical sanding is recommended to remove all wax. Presence of wax on substrates will affect the drying and adhesion of the paint coating Note : For bare wood substrate, sand using sandpaper grade #60 or #80 After applying wood putty / filler, sand using sandpaper grade #150 or #180 After applying stain, no sanding is required before topcoat After applying sealer, sand using sandpaper grade #240 or #280, #320 and #400 (for 1st, 2nd and 3rd coat sealer respectively) Between each topcoat, sand using sandpaper grade #360 or #400 DRYING TIME : Touch Dry : 30 minutes at 30 °C Hard Dry : 1 hour at 30 °C OVERCOATING TIME : 2 hours under normal conditions RECOMMENDED PAINTING : 1-2 coats of WoodStain Filler SYSTEM 3 or more coats of solvent-based wood varnish until a satisfactory wood finish is obtained CLEANING : All equipment should be cleaned with Bodelac 9000 GP Reducer or Mineral Turpentine immediately after use GENERAL INFORMATION SOLID CONTENT : 75.0 ± 2% by weight SPECIFIC GRAVITY : 1.46 ± 2% kg / litre PACKING : 1 litre STORAGE : Store in a tightly sealed container in a cool dry place SHELF LIFE Up to 12 months in a tightly sealed container Page 2 of 3 TECHNICAL DATA SHEET FOR WOODSTAIN FILLER PRECAUTION : Avoid painting when the temperature is below 10°C or above 35°C or when the humidity is over 85% When the surface temperature is 7 °C below, drying and overcoating times will be considerably extended Ensure good ventilation during application and drying of paint This product is flammable. Ensure adequate protection and avoid direct contact on sensitive skin and eyes, etc Refer to the product Safety Data Sheet for more information The information given is intended to give a description of the product performance under specific test conditions. Nevertheless, we cannot assume any responsibility for the use of it since circumstances under which the products are applied in practice are subjected to many variations. We reserve the right to alter the given data without notice. Enquiries / Contact Details : Customer Service 6265 5355 (Main Line) 6264 1603 (Fax) www.nipponpaint.com.sg Page 3 of 3 .
Load more

Recommended publications
  • Reserva Series - Designer Collection Specifications
    General Reserva Series - Designer Collection Specifications White Oak, Cerralvo Products Species White Oak Grade Exclusive: Moderate color variations and wood natural characteristics, such as sound and open knots, as well as knots filled with wood putty, mineral streaks, surface checks and splits. Style Torrefied Maturation The color of the wood may undergo slight discoloration depending on the amount of light the floor is exposed to. This phenomenon, called oxidation, is inherent to the thermally modified products. Texture Smooth Sheen (Gloss Level) Matte (20%) Color Cerralvo Maintenance Recommended hardwood flooring cleaning products Uses Residential & light commercial Warranties Structural: Lifetime (Please refer to the Installation Guide) Finish wear-through: Residential: 35 years Light commercial: 5 years Relative Species Hardness White Oak: 1,360 lbs - 5% harder NWFA Janka - Hardness Test (ASTM-D-143) Red Oak 1,290 lbs* - 100% *lbs = Applied force in pounds Finish TitaniumTM Finish Polymerized titanium finish enhanced with nanotechnology Characteristics Appearance: Superior Durability: Superior Gloss losing resistance: Superior Stain Resistance: Superior Easy to maintain: Superior Easy to repair: Superior Solvent & Water: Free Formaldehyde: Free Antimicrobial Protection ISO 22196 & ASTM G-21 Ultra Fresh (Ultra Fresh is a registered trademark of Thomson Research Associates.) Static Friction Coefficient ASTM D-2394-99 Slippery resistance coefficient more than 0.5 Pure Genius® Smart Floor Technology Air-Purifying Titanium Dioxyde Photocatalytic
    [Show full text]
  • Color Chart.Pdf
    ® Finishing Products Division of RPM Wood Finishes Group Inc. Color Chart The Original Touch Up Company™ Made in the USA Color Chart ® Finishing Products Division of RPM Wood Finishes Group, Inc. Index Aerosols 1-5 Ultra® Classic Toner & Tone Finish Toner 1-3 Colored Lacquer Enamel 3-5 Shadow Toner 5 Touch-Up Markers/Pencils 5-15 Ultra® Mark Markers 5-9 3 in 1 Repair Stick 9 Pro-Mark® Markers 9-10 Quik-Tip™ Markers 10-11 Background Marker Touch-Up & Background Marker Glaze Hang-Up 11-13 Artisan Glaze Markers 13 Vinyl Marker Glaze Hang-Up 14 Brush Tip Graining Markers 14 Accent Pencils 15 Blend-Its 15 Fillers 15-29 Quick Fill® Burn-In Sticks 15-16 Edging/Low Heat Sticks 16 E-Z Flow™ Burn-In Sticks 16-17 PlaneStick® Burn-In Sticks 17-18 Fil-Stik® Putty Sticks 18-25 Hard Fill & Hard Fill Plus 25-27 PermaFill™ 27 Epoxy Putty Sticks 27-28 Patchal® Puttys 28-29 Knot Filler 29 Fil-O-Wood™ Wood Putty Tubes 29 Color Replacement 30-31 Blendal® Sticks 30 Sand Thru Sticks 30-31 Blendal® Powder Stains 31 Bronzing Powders 31 Dye Stains 32 Ultra® Penetrating & Architectural Ultra® Penetrating Stain 32 Dye Concentrate 32 Pigmented Stains 32-34 Wiping Wood™, Architectural Wiping Stain & Wiping Wood™ Stain Aerosols 32-33 Designer Series Stain, Designer Series Radiant Stain 33-34 Glazes 34 Finisher’s Glaze™ Glazing Stain & Aerosols 34 Break-A-Way™ Glaze & Aerosols 34 Leather Repair 35-37 E-Z Flow™ Leather Markers 35 Leather/Vinyl Markers 35 Leather/Vinyl Fil Sticks 35-36 Leather Repair Basecoat Aerosols 36 Leather Repair Toner Aerosols 36 Leather Repair Color Adjuster Aerosols 37 Touch Up Pigment 37 Leather Refinishing 37 Base Coat 37 NOTE: COLORS ARE APPROXIMATE REPRESENTATIONS OF ACTUAL COLORS USING MODERN PROCESS TECHNIQUES.
    [Show full text]
  • Mass Timber Design Guide Crosslam® CLT | Glulamplus® | Mass Timber Building Systems U.S
    Mass Timber Design Guide CrossLam® CLT | GlulamPLUS® | Mass Timber Building Systems U.S. VERSION Penticton Lakeside Resort, Penticton, BC, Canada Mica Heli-Ski Lodge, Mica, BC, Canada Beautifully engineered to change an entire industry. At Structurlam, it’s been our goal for more than 50 years to innovate and push the boundaries of our industry in order to create new limits of what it means to build with wood. Through our experience in bringing buildings to life, we’ve been proud to be part of developing and producing structures in exciting and efficient new ways. In fact, as the industry moved toward evolved, Structurlam has pioneered the use concrete and steel in commercial buildings, of cutting-edge technology and systems to we stayed true to ourselves. We understood bring your project from concept to reality. the advantages of building with wood and of From prefabrication of structural elements to laminating lumber into beams that could be erection on-site, BIM modeling permits the use used in larger structures. We embraced new of mass timber to be highly precise, efficient technology, such as 3D modeling and robotic and cost competitive. machinery, to fabricate complete mass timber By working with us, you’re always assured packages. This allowed us to introduce wood engineering expertise and design efficiency that into buildings where it was never considered reduces time and cost on-site. No job is too in the past. simple or too complex, and we’ll always work to The result is an array of high-performance mass help you build whatever you dream.
    [Show full text]
  • Plant Fiber Panels Installation Guide
    Easy DIY Eco-Friendly 3D Dimensional 3D Wall Board Installation Instruction Light Weight www.art3dwallpanels.com Installation Instruction Ⅰ Preparation: 1. Request for the wall surface 1) The wall surface must be flat,dry,clean and smooth, solid and painted with emulsion paint. 2) Aged wall surface must be smooththened and painted with water-based seal primer to compact the loose surface layer 3) Enviroment request: Open the window and make sure the room is clean and ventilated 2. Preparation for the commodity. Put 5pcs in one stack Open the box, put the boards on the floor Take out the boards for 24hours to balance the moisture carefully between the panel and the enviroment to prevent excessive expansion or contraction after installation 3. Tools Needed Tap Measure Level Pencil Applicator Barrel Brush Putty Knife Sandpaper 4. Supporting Materials All the supporting materials are Dufa products Acrylic water-based Acrylic water-based Acrylic water-based Adhesive (Titebond from wood putty PU wood paint wood seal primer USA recommended.) www.art3dwallpanels.com Installation Instruction Ⅱ Installation Steps 1. Measure the wall and plan the design. 1) Measure and mark horizontally and vertically the area of installation 2) Select a pattern for installation. Arrange it on the floor by rotating the panels before attempting to install ensuring correct installation of the desired pattern. 3) If the area for installation is not square, or just meet the connection of the circuit, the panels can be cutted by knife 2. Adhere with All-purpose adhesive glue (Titebond made in USA recommended) 1) Use the all-purpose adhesive glue to dot on 2) After dot the glue on the boards, put it on the wall the board every 30 to 50 mms on the flat surface, and take it out asap.
    [Show full text]
  • Comparison of Two Wood Filler Types with Respect to Relative Shrinkage Across Variations in Temperature, in Humidity, and Within Wood Species
    CORE Metadata, citation and similar papers at core.ac.uk Provided by The University of North Carolina at Greensboro COMPARISON OF TWO WOOD FILLER TYPES WITH RESPECT TO RELATIVE SHRINKAGE ACROSS VARIATIONS IN TEMPERATURE, IN HUMIDITY, AND WITHIN WOOD SPECIES By Joshua Lee Ellis A Thesis Submitted to the Faculty of the Graduate School of Western Carolina University in Partial Fulfillment of the Requirements for the Degree of Master of Science in Technology Committee: ________________________________________________Director ________________________________________________ ________________________________________________ ________________________________________________Dean of the Graduate School Date: ___________________________________________ Summer 2011 Western Carolina University Cullowhee, North Carolina COMPARISON OF TWO WOOD FILLER TYPES WITH RESPECT TO RELATIVE SHRINKAGE ACROSS VARIATIONS IN TEMPERATURE, IN HUMIDITY, AND WITHIN WOOD SPECIES A thesis presented to the faculty of the Graduate School of Western Carolina University in partial fulfillment of the requirements for the degree of Master of Science in Technology. By Joshua Lee Ellis Director: Dr. Aaron K. Ball Professor of Engineering Technology Kimmel School Department of Engineering Technology Committee Members: Dr. Wes Stone, Engineering Technology Dr. Chip Ferguson, Engineering Technology June 2011 © 2011 by Joshua Lee Ellis Acknowledgements Special thanks to my committee composed of Dr. Aaron Ball, Dr. Wes Stone, and Dr. Chip Ferguson. Specifically, I would like to thank Dr. Aaron Ball for his lifelong commitment to delivering education to students. I have had many teachers throughout my educational career, but none quite like Dr. Aaron Ball. Dr. Aaron Ball is “one of a kind” and it was an honor to have him as a mentor. Dr. Aaron Ball has truly helped me realize that the only person that can stop you from accomplishing your dreams is yourself.
    [Show full text]
  • Wood Surface Preparation
    HF-LRA.054 WOOD SURFACE PREPARATION The key to a successful refinishing job is the preparation of the surface. The wood surface must be smooth and clean; since any scratches will be more noticeable after the finish is applied than they are in the bare wood. Never use sandpaper on an antique. The surface preparation procedure you follow depends on the characteristics of the wood piece and the stripping (if any) procedure you followed. Sanding The majority of the surface preparation should be performed with steel wool. There will be cases, however, when it will be necessary to use sandpaper. If you are working with new wood which has never been finished, it is necessary to sand the wood to get a smooth, even surface. Sanding will also be necessary if the grain of the wood has been raised during stripping. If you must use sandpaper, read this section carefully. Sandpaper is defined by the type of abrasive used and also the size (or grit) of the abrasive particles. The major types of abrasives include: 1. Aluminum Oxide - very hard and durable abrasive grains good for sanding metals and hard woods. 2. Garnet - abrasive grains have very sharp edges, but they are not as tough as aluminum oxide grains. Good for all woodworking operations. 3. Flint - least expensive sandpaper. Flint has sharp edges but dulls fast because of low toughness and durability. Good for woodworking operations. 4. Emery - hard but dull particles that cut slowly resulting in a polishing action. Generally not recommended for use on wood but can be used for final smoothing operation.
    [Show full text]
  • Product Catalogue Australian
    Largest Product Selection TM The Original Touch Up Company 60 Years of Innovation Professional Finishing Products Complete Line of Leather Products Australian Product Catalogue September 2018 Hands-On Training TION AC F S G I U T A A R S A N T 1 E D E INDEX Adhesives Finishes Aerosol Adhesive 37 Clears Industrial Grade Instant Adhesive Cyanoacrylate Glue 37 Classic Instrument Lacquer 33 Loctite Vinyl, Fabric & Plastic Adhesive 37 Clear Spray Shellac 32 Cleaners Finisher’s Choice Clear Lacquer 33 Crystal and Glass Cleaner 02 Finish-Up Polyurethane 29 Quick Clean 02 Outdoor Acrylic Aerosol 31 Wax Wash Remover 02 Perfect Blend 31 Colour Perfect Blend Waterborne 31 Pre-Catalysed Clears 30 Colour Systems Tone Finish Clears 30 Break-A-Way Glaze 26 Ultra Bond Waterborne Clear Finish Marker 29 Bronzing Powder 26 Ultra-Flo Ultra Bond Clear 30 Coloured Lacquer Enamel 25 Waterborne Brushing Urethane 33 Finishers’ Glaze Glazing Stain 26 Waterborne Pre-Catalysed Lacquer 32 Metallic Aerosol 25 Wil Pro Padding Finish 32 Primer Sealer 25 Wiping Wood Stain Aerosol 25 Sanding Sealers E-Z Vinyl Sealer Aerosol 28 Touch-up Colours Pre-Catalysed Sanding Sealer 28 Accent Pencils 21 Tone Finish Flat Easy Sanding Sealer 28 Background Marker 19 Hydro Care Wood Floor System Background Marker Glaze Hang-Up 19 Hydro Care Wood Floor Protector 38 Blendal Powder Stain 23 Hydro Cleaner Wood Floor Cleaner 38 Blendal Sticks 22 Natural Wax Care for Natural Oiled and Pre-finished Floors 38 Block-It Toner 24 Brush Tip Graining Markers 20 Miscellaneous Products Graining Pencils
    [Show full text]
  • 40 CFR Ch. I (7–1–12 Edition) § 63.2291
    § 63.2291 40 CFR Ch. I (7–1–12 Edition) § 63.2291 Who implements and en- ess units associated with the manufac- forces this subpart? turing of plywood and composite wood (a) This subpart can be implemented products. The affected source includes, and enforced by the U.S. EPA or a dele- but is not limited to, green end oper- gated authority such as your State, ations, refining, drying operations (in- local, or tribal agency. If the EPA Ad- cluding any combustion unit exhaust ministrator has delegated authority to stream routinely used to direct fire your State, local, or tribal agency, process unit(s)), resin preparation, then that agency has the authority to blending and forming operations, press- implement and enforce this subpart. ing and board cooling operations, and You should contact your EPA Regional miscellaneous finishing operations Office to find out if this subpart is dele- (such as sanding, sawing, patching, gated to your State, local, or tribal edge sealing, and other finishing oper- agency. ations not subject to other NESHAP). (b) In delegating implementation and The affected source also includes on- enforcement authority of this subpart site storage of raw materials used in to a State, local, or tribal agency the manufacture of plywood and/or under 40 CFR part 63, subpart E, the composite wood products, such as res- authorities contained in paragraph (c) ins; onsite wastewater treatment oper- of this section are retained by the EPA ations specifically associated with ply- Administrator and are not transferred wood and composite wood products to the State, local, or tribal agency.
    [Show full text]
  • CIP March 13.Cdr
    CONTINUAL IMPROVEMENT PROGRAMME 1st March 2013 For internal circulation only Phase - III Vol.:XII Painting – Part 2 3. FINISHING WOOD WORK : 3.2.1.4 On clean prepared surfaces, wood primer is to be applied by brushing, covering all areas uniformly. Surface Wood work is generally finished in five different ways - preparation is as stated above. White or pink primer is as a) painting with synthetic enamel paints [alkyd based in oil] per specification. b) painting with poly urethane based transparent paints [like asian paints' 3.2.1.5 Two primer coats are necessary mainly because of time touch wood or melamine] lapse between making the joinery and fixing in position. Besides while fixing the joinery work [ddors and windows] c) french polish or varnish - transparent finish again with spirit varnish in masonry or concrete, cement mortar and dust are likely [xylene or alcohol based] to settle on the wood work. d) shellac polish – red lac in spirit or oil 3.2.1.6 Again another time lapse may [generally] take place before e) wax polish - linseed oil and bee wax or tung oil with or without colouring final painting on these members are taken up after fixing in pigments The synthetic enamel finish offers protection to wood, position [making done parallel to RCC frame work, then completely covers the natural grains or texture of the wood [may be walls are taken up during which these frames go into many may not like this]. Other finishes retain the wood's natural grain position. After plastering & floor finishes are done, this appearance and at the same time offers protection to wood.
    [Show full text]
  • Technical Data Sheet
    Manufactured by: Eclectic Products, Inc. Pineville, LA 71360 TECHNICAL Made in the USA DATA SHEET 800.767.4667 - Technical Services eclecticproducts.com Wood-Tex® Synthetic wood-tex.com Wood Filler PRODUCT DESCRIPTION Wood-Tex® is a resin-based wood filler, developed for the plywood and furniture industries, used to repair defects in plywood, furniture, laminated beams, cabinet work, and other woodwowrking applications. It molds like putty and is consistent, uniform, waterproof and fast-setting with minimal shrinkage. Made with genuine wood flour, Wood-Tex® can be sanded, stained, sawed, planed or drilled like ordinary wood. PRODUCT CHARACTERISTICS and BENEFITS High solid content Saw, drill, sand, plane and nail, just like real wood Fast dry time Indoors and outdoors Easy application Spreads evenly into cracks and holes without crumbling or cracking Superior strength Hard finish with little or no shrinkage Quality finish Takes stains and paints evenly with minimal sanding PHYSICAL PROPERTIES OF WOOD-TEX SYNTHETIC WOOD FILLER Color(s) 6: Cherry/Dark Mahogany, Fir/Maple, Natural/Ash, Red Oak, Walnut, White Pine Density 12 - 13 lbs/gal Solids 75% ± 1.0% (by weight) Viscosity 440,000 to 550,000 cps Vehicle Nitrocellulose Lacquer Volatile content 12.69% ± 0.07% (VOC 215 g/L) Storage Store between 45 and 85 °F (7 and 29 °C) Freeze/thaw stability None; do not freeze Shelf life 1 year DIRECTIONS FOR USE and APPLICATION NOTES Please read all directions before using. Always test a small area before full use. Step 1 For best adhesion, crack or defects should be clean and dry. Step 2 Press firmly into defect by hand, or with putty knife.
    [Show full text]
  • EZ Click Hardwood Flooring Installation, Care and Warranty Guide
    EZ Click Hardwood Flooring Installation, Care and Warranty Guide Warranty coverage may be lost due to failure to strictly abide by all the installation instructions and recommendations in this manual. This includes the use of improper tools and materials. Read all instructions carefully. Rev.20091120 Part I INSTALLATION AND CARE: Product Description: EZ Click hardwood flooring planks are designed for use in multiple locations. Acceptable location includes basements, ground floors or high-rise buildings. EZ click flooring can be floating on, directly nailed or glued to a wooden or concrete sub-floor. Professional advice should be sought for the type of glue and method of glue-down installation to ensure trouble free installation. EZ Click flooring is made of a wear layer of solid wood lamella mounted under high pressure to produce premium quality flooring. These products are pre-finished under ideal conditions that meet or exceed industry standards. Where to install and Method to install: Grade Type Staple Down Glue Down Floating Above Grade Yes Yes Yes On Grade Yes Yes Yes Below Grade No No Yes Sub-floor Type Staple Down Glue Down Floating Concrete No Yes Yes Plywood & OSB Yes Yes Yes Old wooden floor, particleboard, pressed board & other non-wood Site Specific Site Specific Yes sub-floor Site Specific – depending on the degree of levelness, firmness and soundness of the sub-floor. Sub-floor should be sound, level and free of debris. The following is as defined by NWFA Hardwood Flooring Installation Guidelines - Section V for moisture testing: Concrete moisture readings are not to exceed 4.5% on Tramex Concrete Moisture Encounter meter.
    [Show full text]
  • Understanding Wood Finishing –
    UNDERSTANDING WOOD FINISHING How To Select And Apply The Right Finish By Bob Flexner WHY FINISH WOOD, ANYWAY? Sanitation Stabilization Decoration PREPARING THE WOOD SURFACE Preparing the Lumber Sanding and Smoothing Sponging Sharpening a Hand Scraper Sharpening a Cabinet Scraper Solvents for Removing Cured Glues Glue Splotches Dents, Gouges, and Holes Wood Putties TOOLS FOR APPLYING FINISHES Rags Brushes Rubbing Pads Spray Guns and Equipment Common Spraying Problems OIL FINISHES Our Ancestors and Linseed Oil Applying "Oil" Finishes Oil Finishes and Penetration How Oil and Oil/Varnish Finishes Protect Types of "Oil Safety and Oil Finishes Using Wax as a Finish Bleeding Oil Finishes Which One Is Which? How to Tell Which "Oil" You Have How to Maintain and Repair "Oil" Finishes Guide to "Oil" Finishes STAINING WOOD What Makes a Stain Understanding Stains A Guide to Stains Using Aniline Dyes Bleaching Wood Chemical Stains Ebonizing Wood Matching Color A Sampler of Wood Stains Solvents and Thinners for Dyes and Stains Compatibility of Stains and Finishes How Woods React to Stains Applying Stain Applying Glaze Pickling Common Staining Problems, Their Causes, and Solutions FILLING THE PORES Filling the Pores with the Finish Filling the Pores: Finish versus Paste-Wood Filler Filling the Pores with Paste-Wood Filler Using Oil/Varnish Paste-Wood Filler Using Water-Based Paste-Wood Filler INTRODUCTION TO FILM FINISHES........... What's in a Name? Sealers and Sanding Sealers The Way Finishes Cure Finishing Materials: How They Cure Stain and Finish
    [Show full text]