To Install, up to 90" Mounts in Minutes 165 Lbs
Total Page:16
File Type:pdf, Size:1020Kb
Thin Profile | Fixed Position Flat Screen TV Mount User Manual Easy to install, UP TO 90" mounts in minutes 165 lbs. Max Questions? Call 1-800-654-8483 M–F, 7:30am–5:00pm CST Model 23158 or visit www.jascoproducts.com 05/20/13 ver1 2 Thank you for purchasing this GE product! The GE Flat Panel Wall Mount allows you to easily, quickly and securely mount your flat screen display to a wall. Please review these instructions carefully before beginning installation. Please verify the mounting hole locations (VESA compatibility) of your display to ensure proper installation. For further detailed instructions, please visit our website at www.jascoproducts.com. SPECIFICATIONS 6. Follow all instructions and • Display Size: 42" to 90" recommendations regarding adequate • Maximum Load: 165 lbs (75kg) ventilation and suitable locations for • VESA Mounting Pattern: mounting your display. Consult the owner’s 800mm x 500mm Max manual for your particular display for more • Profile: 1" (2.5cm) information. 7. Seller/manufacturer is not liable for damages or injury caused by incorrect TOOLS REQUIRED* mounting, assembly or use. • Phillips Screwdriver 8. This product contains small items that • Ratchet or Driver with 1/2" (13mm) socket could be a choking hazard if swallowed. • Drill & drill bit (1/4" (6mm) drywall; Keep these items away from children. 3/8" (10mm) concrete) • Wall stud locator (drywall installation) **This wall mount is for indoor *Tools not included installation only** WARNINGS HARDWARE KIT A 1. Read these instructions carefully before A - M8 x 63 Lag Bolt (x6) you begin. If you are unsure of any part of the process, contact a professional B - Lag bolt washer (x6) contractor or installer for assistance. C - Concrete anchor (x6) C Improper installation can result in injury B or damage. D - M6 x 12 screw (x4) E 2. Use with products heavier than 165 lbs. E - M6 x 30 screw (x4) (75kg) may result in instability and D F - M8 x 12 screw (x4) possible injury. G 3. The wall or mounting surface must be G - M8 x 30 screw (x4) capable of supporting the combined weight F H - Spacer (x8) of the mount and the display; if not, the I structure must be reinforced. I - M6 Washer (x4) 4. Safety gear and proper tools must be used. H Failure to do so can result in injury and/or damage. 5. A minimum of two people are required for installation. Do not attempt to install this mount alone under any circumstances. 3 DRYWALL INSTALLATION CONCRETE INSTALLATION INSTRUCTIONS INSTRUCTIONS **IMPORTANT** For safety reasons, this **IMPORTANT** For safety reasons, the mount must be secured to a wood stud concrete wall must be capable of supporting capable of supporting the combined weight the combined weight of the mount and the of the mount and display. **DO NOT MOUNT display. The seller/manufacturer takes no TO DRYWALL ALONE** responsibility for the failure caused by walls or insufficient strength. 1. Use a high quality stud finder to locate the stud where you wish to install your mount. **IMPORTANT** If installing the mount onto Mark both edges of the stud to help identify a concrete block or brick surface, never drill the exact center. into the mortar between blocks or bricks. NOTE: You must use the center of each stud to YOU MUST SECURE THE MOUNT TO THE avoid cracking or splitting the wood during CONCRETE BLOCK OR BRICK. installation. 1. Place the wall plate against the wall in 2. Place the wall plate against the wall and the desired location and level it using the level it using the included bubble level. included bubble level. 3. While another person holds the wall plate in 2. While another person holds the wall plate in position, mark two locations per stud for the place, mark the four locations for each lag lag bolts (A) used to secure the mount to bolt (A) on the wall for securing the mount the wall (See Fig. 1). (see Fig. 3). 3. Drill an 3/8” (10mm) hole at FIG. 3 each marked FIG. 1 location. Remove any excess dust from the holes. 4. Insert a concrete 4. Drill a 1/4” (6mm) pilot hole at each anchor (C) into each marked location. hole so that it is 5. Place the wall plate back against the wall flush with the concrete and attach it using the lag bolts (A) and lag surface (see fig. 4). bolt washers (B) provided in the hardware A hammer can be kit (see Fig. 2) Do not overtighten these used to lightly FIG. 4 bolts and do not release the wall plate tap the anchors until all bolts are in place. into place if necessary. FIG. 2 Ensure that the wall plate remains level after all bolts are secured. 4 5. Place the wall plate back against the wall Do not force any of the screws — if you and attach it using the lag bolts (A) and lag feel resistance, stop immediately and try bolt washers (B) provided in the hardware a smaller diameter screw. kit (See Fig. 2). Do not over-tighten these 3. Attach the mount arms to the back of your bolts and do not release the wall plate display using the screws identified in Steps until all bolts are in place. 1 and 2: A. If you are using the M6 screws you will also need to use the M6 washers (I). M8 screws do not require washers. B. If you are using the longer screws on a display with a curved and recessed back, FIG. 2 you may also need to use the spacers (H). Ensure that the wall plate remains level after all bolts are secured. Use one spacer or two spacers stacked as needed. Only use a spacer ATTACHING THE MOUNT if necessary. ARMS TO THE DISPLAY For displays For displays **IMPORTANT** Use extra care during this with flat with curved backs or recessed part of the installation. If possible, avoid backs placing your display facedown as it may damage the viewing surface. NOTE: This mount comes with a selection of different screw diameters and lengths to accommodate a wide variety of display/ 4. Attach the mount to the back of your monitor/television models. Not all of the display using the screws identified in Steps hardware in the kit will be used. If you 2 and 3. If you are using the longer screws cannot find the appropriate screw size in the on a display with a curved or recessed kit provided, consult the manufacturer of back, you may also need to use the spacers your display for more information. (H) provided in the hardware kit. Only use a spacer if necessary. 1. Examine the mounting holes on the back of your display to determine the correct length of screw to use: A. If the back of your display is flat and the FINAL ASSEMBLY mounting holes are flush with the 1. With the help of another person, carefully surface, you will use the shorter screws lift your display and place it on the wall (D, F) from the hardware kit. mount plate. Do not release the display B. If the back of your display is curved, has until the mount arms have securely a protrusion, or if the mounting holes are hooked onto the wall mounting plate. recessed, you will need to use the longer 2. Insert the safety bar at the bottom of the screws (E, G) and the spacers (H). mount to prevent the display from being 2. Determine the correct diameter of screw to lifted from the wall plate. Insert safety use by carefully trying one of each size (M6 stopper into the end of the safety bar to and M8) from the hardware kit. prevent bar from being removed. A padlock (not included) can be inserted into the end of 5 FIG. 5 Safety bar with Oklahoma City, OK 73114. safety stopper in place (included). Please contact technical support (using one of the listed options) before attempting to ship product returns or warranty requests. Failure to do so may delay processing times considerably. 1-YEAR LIMITED WARRANTY Jasco Products Company warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase. Safety bar with padlock in place (Padlock not included). This warranty is limited to the repair or the bar to help prevent theft of your display replacement of this product only and does (see Fig. 5). not extend to consequential or incidental damage to other products that may be **IMPORTANT** The safety bar should be used with this unit. This warranty is in lieu used at all times to prevent the display from of all other warranties express or implied. being accidentally knocked from the mount. Some states do not allow limitations on how 3. Periodically clean your mount with a dry long an implied warranty lasts or permit cloth. Inspect all screws and hardware the exclusion or limitation of incidental at regular intervals to ensure that no or consequential damages, so the above connections have become loose over time. limitations may not apply to you. This Re-tighten as needed. warranty gives you specific rights, and you may also have other rights which vary from state to state. If unit appears to be defective within the warranty period, please contact TECHNICAL SUPPORT: out technical support team for assistance For additional assistance: (Technical Support’ section in the manual). Online: www.jascoproducts.com/support Email: [email protected] Our in-house call center is open M-F, 7:30am-5:00pm CST (except holidays and special events).