DOCSLIB.ORG

How to Turn a Dip Pen by Wanjun on July 23, 2015

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
How to Turn a Dip Pen by Wanjun on July 23, 2015 technology workshop living food play outside How to Turn a Dip Pen by Wanjun on July 23, 2015 Table of Contents How to Turn a Dip Pen . 1 Intro: How to Turn a Dip Pen . 2 Step 1: Tools and Supplies . 2 Step 2: Turn a Tenon . 4 Step 3: Cut Brass Tube to size . 4 Step 4: Drill a Hole to Length . 4 Step 5: Glue in the Brass Tube . 5 Step 6: Square off the End . 5 Step 7: Turn Holder to Size . 5 Step 8: Rough Shape then Fine Shape . 6 Step 9: Finish the Body . 7 Step 10: Part off the Pen . 7 Step 11: Turn a Jam Chuck . 7 Step 12: Finish the Tip . 8 Step 13: Assemble and Enjoy! . 8 Related Instructables . 9 Advertisements . 10 Comments . 10 http://www.instructables.com/id/Custom-Nib-Holder/ Author:Wanjun 3D Print all the things! Intro: How to Turn a Dip Pen I recently started practicing pointed nib calligraphy and found commercially-made nib holders wanting. They're either too plasticky and light or too expensive so I decided to make some myself. It was surprisingly easy! You don't need a pen kit or any bushings. The finished dip pen is beautiful and most importantly balanced. This project is very inexpensive if you have access to a wood lathe. The lathe parts required are standard with the exception of the 7mm drill bit. The trick is turning a jam chuck yourself so you don't have to buy a fancy closed-end pen mandrel and its specialty chuck. Step 1: Tools and Supplies Tools: Wood lathe with the following parts and big enough to turn 12 inch stock chuck with jaws that can compress down to about 1/2 inch diameter live center drive center drill chuck 7mm drillbit Tube Cutter Calliper (not pictured) Turning tools. I like carbide for rough shaping and HSS for final shaping and detailing. PPE - safety goggles and respirator Supplies: Turning Stock - I used black and white ebony 3/4 inch by 3/4 inch by 12 inch that I ripped from a larger square stock. I recommend tight-grained dense hardwoods such as lignum vitae, desert ironwood, tulipwood, etc. I made my first one out of cherry and it was too light. Sandpaper - varying grit from 150 to 600 Finish - I used a walnut oil and beeswax finish. Use anything you like. Masking tape 7mm brass tube - I bought a 10 pack for all of $2.50 from pennstate where you can also pick up the 7mm drill bit. if you don't want to pay for shipping you can get them at your local Rockler or Woodcraft. CA Glue - or super glue Pen Insert - holds the nib in regular nib holders. I haven't been able to find them anywhere but JohnNealBooksellers which is also where I buy all my calligraphy supplies. Sugru - optional. http://www.instructables.com/id/Custom-Nib-Holder/ Image Notes 1. 4-Jaw Chuck 2. 7mm Pen Bradpoint Drill 3. Live Center 4. Drive Center 5. Drill Chuck Image Notes 1. Pen Inserts 2. 7mm brass tube http://www.instructables.com/id/Custom-Nib-Holder/ Step 2: Turn a Tenon 1. Decide on the orientation. Tail end should go on the tail stock. 2. Turn a tenon on the tailstock side. Step 3: Cut Brass Tube to size It should be able to house the pen insert. See photo for precise measurements. Step 4: Drill a Hole to Length 1. Take your live and drive centers off and chuck up your tenon with the 4-jaw chuck. 2. install drill chuck with pen drill on the tail end 3. use masking tape to mark on the drill correct depth. 4. drill into the wood until you hit the masking tape. http://www.instructables.com/id/Custom-Nib-Holder/ Step 5: Glue in the Brass Tube Before you apply CA glue test fit it to make sure the hole is deep enough. Step 6: Square off the End Wait for the glue to dry and carefully square off the end to free it of leftover CA and to make flush brass tube and wood. Step 7: Turn Holder to Size 1. Put the live center back on the tail stock. 2. Rough down your stock. 3. With your calliper measure the insert and turn down the nib end to for a seamless joint. http://www.instructables.com/id/Custom-Nib-Holder/ Step 8: Rough Shape then Fine Shape Customize and shape the pen. I held it intermittently with my writing hand to make sure it felt right. Remember to always turn downhill. Finalize the thicker diameter shape before tapering off the thin end. At this point I noticed a wormhole right in the middle grrrr! I just left it alone. http://www.instructables.com/id/Custom-Nib-Holder/ Step 9: Finish the Body I sanded to 600 grit and rubbed in my walnut oil and beeswax finish with a shop towel. Step 10: Part off the Pen Loosen your tail stock a bit. This is to relieve pressure off the spindle, allowing for a very fine part. I parted this by tapering down, with light cuts and a sharp tool. Step 11: Turn a Jam Chuck The tip from when we parted off is unfinished so this is all for finishing the tip. Use the calliper to measure the inside diameter of the brass tube and turn a recess down to just a hair smaller. Wrap the masking tape around a couple of times, tear off excess and jam the pen onto the jam chuck. ` http://www.instructables.com/id/Custom-Nib-Holder/ Step 12: Finish the Tip Sand down and finish the tip as you did the body. The makeshift jam chuck does not spin true and will only become more and more wobbly so support it with your fingers, and always sand from right to left. Step 13: Assemble and Enjoy! Hand press the pen insert in your holder and put a nib in it! It's a joy to use and makes me look forward to practicing calligraphy. If you don't mind permanently marrying a nib to a holder, use Sugru instead of a pen insert. Sugru has the added benefit of waterproofing the nib holder. I also added in a small ball bearing to weigh down very first one I made out of cherry. http://www.instructables.com/id/Custom-Nib-Holder/ Related Instructables Fountain Pen Care! by Make a A Steel Dip Pen Quill Dipping DIY Calligraphy Create A CowGuy calligraphy pen Nib by sdfgeoff Pen by gravitino Nibs by Custom out of a bulrush advicevice Medieval- /Fantasy-Style (cattail) reed by Calligraphy Rectifier Quill by nevdull http://www.instructables.com/id/Custom-Nib-Holder/ Advertisements Comments 4 comments Add Comment Edbed says: Jul 24, 2015. 1:56 AM REPLY Great instructable. Wanjun says: Jul 24, 2015. 3:07 PM REPLY Thank you! antagonizer says: Jul 24, 2015. 2:18 PM REPLY I noticed the sandpaper stained your pen. That's my biggest pet peeve when working with light colored wood on my lathe. You can get tan colored 400-600 grit paper, but its hard to find. The best way, I found to beat it is to wet the wood only as the water breaks down the paper causing the grit to wear off, then as the paper gets wet, replace it. Awesome pen btw. Makes me want to turn one. Wanjun says: Jul 24, 2015. 2:49 PM REPLY I didn't even notice! I always thought color deepening of light woods was caused by polishing and oiling so I'll definitely keep an eye on it and wet the wood next time. I actually prefer 400 and 600 Abranet mesh - no grit coming off and they lasts forever, this might convince me to get the rough grits. http://www.instructables.com/id/Custom-Nib-Holder/.
Load more

Recommended publications
  • Special Edition
    www.bearing-news.com SPECIAL EDITION ISSUE 202018 • P918438 BEARING INDUSTRY MAGAZINE SKF EITAN VESELY BEARINGS FOR THE FOOD & BEVERAGE INDUSTRY [email protected] or +44 (0) 1227 793 334 In our industry, the highest standard we can achieve for our Quality Management System is the ISO 9001 certification - awarded by TUV Rheinland. It is the global benchmark that guarantees a total focus on customer service and continual improvement. www.zen.biz All at ZEN Group Wish You Merry Christmas and a Happy New Year ! Online BEARING EXPO & B2B MEETINGS in 2021 Publisher Together with this new special edition of the interview that highlights the current technological BEARINGNEWS COMMV BearingNEWS magazine, I am pleased to announce the level and where the bearing industry is heading to. Camille Huysmanslaan 27/15 online BEARING EXPO & B2B MEETINGS event 2020 Antwerpen - BELGIUM on 15 – 17 March 2021. BEARING EXPO & B2B Mergers & Acquisitions MEETINGS is a unique chance and perfect opportunity More than ever before, small, and medium size Phone : +32 (0)489 32 85 21 Fax : +32 (0)3 303 52 82 to catch the moment and expand bearing and power bearing, and power transmission companies E-mail : [email protected] transmission companies digital presence worldwide are willing to move into strategic mergers and Web : www.bearing-news.com through this first ever, top tier online organization. long-term partnerships. An overview of M&A projects and specific acquisition searches by ICT Do not let the travel restrictions thwart your product Advisory Division can be read on page 40-41.
    [Show full text]
  • Purpleheart Tree PREZ SEYZ 2
    FEBRUARY 2019 What’s Inside PREZ SEYZ Page 2 GALLERY OF BOWLS Page 4 TEN HARDEST WOODS Page 12 USE OF SPACER BLOCKS WITH PENS Page 15 PEN WOOD OF MONTH Page 18 Purpleheart Tree PREZ SEYZ 2 Hey woodturners, How you doing? What can I say, just keep shoveling! So much for a mild win- ter. As most of you are aware, the February meeting was canceled because of weath- er. If you didn't get the email notice, I apologize. It may have gone out on an older mailing list. So that being a situa- tion, if you need to send info out to club members, make sure you have the latest list. You can get it from Randy. If you have bowls yet for "Feed My People " please contact me at [email protected] and I will get them from you. Each of you who are signed up to do a demo at a club meeting, please just move your demo forward one month. If that can't work, let me know. We are always looking for new ideas for demos for club meetings. If you would like a demonstration on a given area of wood turning, let me know and we will try to get in in the schedule. For those of you who like to turn natural edge bowls, now is the time to cut the trees before the sap starts to flow. The bark is less likely to loosen. Obviously because on no meeting this month our letter will be somewhat shorter. I give Tom credit for his creativity in making it informative, Thanks Tom ! Well again as Bugs Bunny sez, "That's all folks" Prez Duane.
    [Show full text]
  • Guaiacum Sanctum: Lignum Vitae1 Edward F
    ENH445 Guaiacum sanctum: Lignum Vitae1 Edward F. Gilman, Dennis G. Watson, Ryan W. Klein, Andrew K. Koeser, Deborah R. Hilbert, and Drew C. McLean2 Introduction Uses: tree lawn 3–4 feet wide; tree lawn 4–6 feet wide; tree lawn > 6 ft wide; sidewalk cutout (tree pit); parking lot Lignum vitae is an extremely slow-growing broadleaf island < 100 sq ft; parking lot island 100–200 sq ft; parking evergreen which ultimately reaches 30 feet in height and lot island > 200 sq ft; container or planter; specimen; deck casts light shade, but few people have seen plants of this or patio; Bonsai; highway median size because it is not grown in the trade. Most are seen 8 to 12 feet tall with a beautiful array of multiple trunks and a rounded canopy much like that of a mature crape-myrtle. The one to two-inch-long, leathery, dark green leaves are joined at many times throughout the year by the production of large clusters of bluish purple flowers, the old flowers fading to a light silvery-blue and creating a shimmering haze over the rounded canopy. These flowers are followed by small, heart-shaped, yellow orange berries, appearing on the tree at the same time as the bluish purple flowers and creating a lovely sight. General Information Figure 1. Full Form—Guaiacum sanctum: Lignum vitae Scientific name: Guaiacum sanctum Description Pronunciation: GWY-uh-kum SANK-tum Height: 10 to 30 feet Common name(s): Lignum vitae, holywood, tree of life Spread: 8 to 12 feet Family: Zygophyllaceae Crown uniformity: symmetrical USDA hardiness zones: 10B through 11 (Figure 2) Crown shape: round, vase Origin: native to Florida, the West Indies, Mexico, and Crown density: dense Central America Growth rate: slow UF/IFAS Invasive Assessment Status: native Texture: fine 1.
    [Show full text]
  • Is Guaiacum Sanctum Effective Against Arthritis? an Ethnobotany
    Is Guaiacum sanctum Effective Against Arthritis? An Ethnobotany Case by Eric Ribbens, Barbra Burdett, and Angela Green Department of Biological Science Western Illinois University Part I—Anecdotal Evidence Dr. Beth Tonoany is a tropical population ecologist who has been studying an unusual tree, Guaiacum sanctum, which once grew throughout the dry tropical forests of Central America as well as on some of the Caribbean islands. Guaiacum sanctum produces a wood called lignum vitae, and is known in Costa Rica and other Spanish-speaking countries as guayacan reál. The wood is extremely heavy because it contains extensive deposits of resin (Howes, 1949) and it will sink if placed in water (Wilson and Eisner, 1968). During World War I and II it was extensively harvested for use in the ship-building industry because the wood, which does not split easily, is self- lubricating due to its high resin content. The wood is very durable, and was in high demand for constructing bearing sleeves to support ship propellor Figure 1: Seeds of shafts (Scurlock, 1987). It has also been used for making railroad ties Guaiacum sanctum (Woods, 1951). Dr. Tonoany has been studying one of the last remaining populations of lignum vitae in the Palo Verde Nature Preserve in northwestern Costa Rica. Probably fewer than 100 trees remain in Costa Rica, most in the Palo Verde Nature Preserve. Her research has included tracking seedlings and saplings, locating and measuring adult trees, and interviewing some of the local Ticos to learn about the tree’s past history in Costa Rica. The tree, while rare now due to the dramatic conversion of tropical deciduous forest in Costa Rica into pasturelands and to selective logging of the tree for its valuable wood, was once more common, and many of the older Ticos remember that the saplings were used to make cattle switches because of the strong flexible wood in the saplings.
    [Show full text]
  • Montserrat Geothermal Drilling 2015 EIA
    MINISTRY OF COMMUNICATIONS, WORKS & LABOUR P O BOX 344, BRADES, MONTSERRAT, W I Tel: (664) 491-2521/2522 Fax: (664) 491-6659 E-mail: [email protected] Draft Environmental Impact Assessment for Geothermal – Drilling of the 3rd Exploratory Production Well Prepared and Submitted by ATOM Solutions Incorporated If there are any comments, questions or suggestions they can be submitted in writing to [email protected] Government of Montserrat Environment Impact Assessment For Geothermal – Drilling of the 3rd Exploratory Production Well Prepared and Submitted By November 2015 Executive Summary This EIA seeks to assess the Environmental and Social impacts of a suite of variables identified in the TOR and the Scoping Report. The assessment includes a baseline for each variable followed by a discussion on impacts on the physical, natural, human and social environments. However, since the drilling is taking place in an elevated area on St. George’s Hill, in Zone V, which was evacuated after the 1995 eruption and has remained a restricted area, there are limited human and environmental impacts expected from the drilling of MON-3. Most of the vegetation is secondary forest and scrub. No sensitive or endangered flora and fauna are at risk. The hillside vegetation was once covered in ash. The Belham Valley forms a low lying area north of St. George’s Hill. This has been heavily inundated with volcano muds left over from lahars. Importantly, the drill site was selected not only for its geothermal potential, but also because it’s elevated provides protection from lava flows which may arise from future eruptions.
    [Show full text]
  • Chatter and Catches the Newsletter of The
    Chatter and Catches the Newsletter of the - November 2017 Volume 10, Issue 6 Detail Gouge Turn Here for Safety October was a fairly quiet month for the club. Some group tool and Never use your fingers to check supply orders and a fun hands-on. I picked up a Grex air sander and the work for roundness while had it broken-in within a few days. Great tool. the lathe is running, especially I tagged along to the Silver Stage High School with our past and po- during roughing operations. tential future president John Compston (that sounds like a good title Stop the lathe to check the pro- gress, or rest the blade of the tool lightly against the work as it turns. for a sci-fi story). John spent the day demonstrating the fundamentals of spindle turning. He showed rough- ing a piece to round, turning beads and coves, parting off, and then using those techniques to turn a simple ornament. John repeated this for six different classes while I watched and learned. I hope to do a little more on our next trip. At the November meeting, Frank Miller and Dave Mills will be doing a tag team demonstration on finish- ing, embellishing, and the ins and outs of tool making. We also will be holding our annual election of club officers. Current officers, with the exception of Pres- ident and Secretary are running for reelection, so we will need at least two members to run for the open positions (and the other positions if you are interested).
    [Show full text]
  • Guaiacum Sanctum Country – MEXICO Original Language – English
    NDF WORKSHOP CASE STUDIES WG 1 – Trees CASE STUDY 7 Guaiacum sanctum Country – MEXICO Original language – English NON-DETRIMENT FINDINGS REPORT ON GUAIACUM SANCTUM IN MEXICO AUTHORS: Leonel López-Toledo David F.R.P. Burslem Miguel Martínez-Ramos Alejandra García-Naranjo I. BACKGROUND INFORMATION ON THE TAXA 1. BIOLOGICAL DATA 1.1. Scientific and common names Guaiacum sanctum, Linnaeus (1753). Most authors identify four or six species in the genus Guaiacum. Four different synonyms have been recognized for G. sanctum: 1.Guaiacum multijugum Stokes (1812). 2.Guaiacum guatemalense Planch. ex Vail & Rydberg likely to be an hybrid between G. sanctum and G. coulteri (Porter 1972). 3. Guaiacum sloanei Shuttl. ex A. Gray (Gray 1897, Vail & Rydberg 1910). 4.Guaiacum verticale Orteg. (Gray 1897, Vail & Rydberg 1910). Guaiacum sanctum is commonly called lignum vitae in English, and guayacan or palo santo in Spanish. Guaiacum coulteri, a very similar species to G. sanctum, is also called guayacan or lignum vitae. 1.2. Distribution Guaiacum sanctum is found in Mexico, Nicaragua, Puerto Rico, the Dominican Republic, the United States (Florida), Costa Rica, Guatemala, Bahamas, Haiti, Cuba, Honduras, El Salvador, Trinidad and Tobago, and the Turks & Caicos Islands. In some of these countries, G. sanctum has become endangered or is virtually extinct. The Mexican populations cover a greater portion of the species’ natural range than those in any other country. There is no data available for the global population. However, a worldwide analysis of the tropical dry forest estimated a remaining range of 131,087 km2 for North and Central America including Mexico. In general this coincides with presence information of G.
    [Show full text]
  • Turning Threads in Wood -- It's Easier Than You Think
    Turning Threads In Wood -- It's Easier Than You Think David Gould I first became interested in thread chasing while watching the Mike Mahoney video “Hollow Forms And Urns – A Workshop”, in which Mike threaded a disk of boxwood that became a collar insert for an urn, into which a blackwood finial was later threaded. When I spent a week in Mike’s workshop in Provo, Utah, last December, I pressed him to include thread chasing among the projects we would attempt. We wound up tackling thread chasing on our last afternoon and never got around to making inserts. We simply covered making inside and outside threads. Tonight, the demonstration will cover the basics and some additional projects that can be accomplished using these skills. Materials: Good threading can only be accomplished on woods that are dense, dry, stable and close grained. Most of the native woods we are accustomed to working with (Maple, Black Walnut, Cherry, Box Elder and others) are not suitable for thread chasing as they are too soft or too brittle. Woods that are good for threading: Boxwood Lignum Vitae African Blackwood Pink Ivory Osage Orange There are other exotic woods that thread well but the above are the more well known. There are synthetic materials that can be used for practice: Corian Resin blanks (pen) The wood used must be dry so that there is no later movement which would result in threads that would bind. Specific Gravity: The measure of the “denseness” of wood is its Specific Gravity. Specific Gravity is the comparison of the weight of a cubic foot of water at sea level (which is 62.4 lbs/cu.ft.) to the weight of a cubic foot of wood.
    [Show full text]
  • Holiday Cookie Bash, 2006
    BULLETIN OF THE PUGET SOUND MYCOLOGICAL SOCIETY Number 428 January 2007 Holiday Cookie Bash, 2006 page 1 MEMBERSHIP MEETING Spore Prints Tuesday, January 9, 2007, at 7:30 PM at the Center for Urban Horticulture, 3501 NE 41st Street, Seattle is published monthly, September through June by the Our speaker for January is Daniel Winkler, and his topic will be PUGET SOUND MYCOLOGICAL SOCIETY “The Mushrooming Fungi Markets in Tibet.” Center for Urban Horticulture, Box 354115 University of Washington, Seattle, Washington 98195 For centuries, Tibetans have collected and (206) 522-6031 http://www.psms.org traded mushrooms. Improved communication User name: Password: and the commoditization of natural resources have caused an astounding mushrooming of OFFICERS: Patrice Benson, President the fungus industry. The market is dominated Joanne Young, Vice President John Goldman, Treasurer by the caterpillar fungus “yartsa gunbu” Dennis Oliver, Secretary (Cordyceps sinensis), matsutake (Tricholoma matsutake), and morels (Morchella spp.). An TRUSTEES: Molly Bernstein, Colleen Compton, Amanita Marilyn Droege, Steve Haynack, array of other mushrooms—such as , Armillaria, Auricularia, Boletus, Cantha- Younghee Lee, Jamie Notman, Dan Winkler Lynn Phillips, Carissa Thornock, rellus, Ganoderma, Hericium, Lactarius, Doug Ward Leccinum, Paxillus, Ramaria, Rozites, Sarcodon, and Suillus—is Ron Post (Immed. Past Pres.) also economically important. ALTERNATE: Luis Felix Yartsa gunbu (Cordyceps sinensis) alone accounts for over 95% SCI. ADVISOR: Dr. Joseph F. Ammirati of the fungi market in Tibet. Currently it is the world’s most precious EDITOR: Agnes A. Sieger, 271 Harmony Lane, fungus at over $30,000/kg retail. In Tibet, it contributes 40% to Port Angeles, WA 98362 the rural cash income.
    [Show full text]
  • Atocha Wooden Bed Post, Tag #85413
    Mel Fisher’s Treasures – On-Line Research Archives Document ©2019 MOTIVATION, INC Atocha Wooden Bed Post, Tag #85413 By James Sinclair, MA Perhaps one of the more unique finds from the Atocha over the past permit period is that of a turned wooden bed post. Turned Lignum Vitae Bed Post, tag #85413, found by the Dare on 10-18-2014 Length: 144.8 cm. Width: 9.5 cm. Min. Width: 15 mm Weight 8.4 kg. This fragment of opulent furniture was located not far from the Primary Cultural Deposit. The Wood was so hard that when first located crew believed that the object might be modern. The first order of investigation was to identify the type of wood that the bed post was made of. For wood identification we have used the services of; Alden Identification Service 3560 Brookeside Drive Chesapeake Beach, MD 20732 http://woodid.homestead.com/ais.html Property of Motivation, Inc. – PuBlished on Mel Fisher’s Treasures On-Line Research Archives Page 1 of 3 Mel Fisher’s Treasures – On-Line Research Archives Document ©2019 MOTIVATION, INC Dr. Alden identified our post as Lignum Vitae (from Latin “Tree of Life”) a portion of the report follows: 1 - Furniture Lignum-vitae Guaiacum sp. Lignum-vitae (Guaiacum spp. L. /Zygophyllaceae), also known as Guayacan or Gai"ac, is composed of aBout 5 species of slow growing shruBs and trees in the Caltrop Family (Zygophyllaceae), native to subtropical and tropical regions of Central and South America. The five recognized species are: 1. Guaiacum angustifolium Engelm. -Texas Lignum-vitae (Texas, Northeastern Mexico) 2.
    [Show full text]
  • Lignumvitae Key Botanical State Park
    Lignumvitae Key Botanical State Park APPROVED Unit Management Plan STATE OF FLORIDA Department of Environmental Protection Division of Recreation and Parks April 23, 2012 TABLE OF CONTENTS INTRODUCTION ..........................................................................................................1 PURPOSE AND SIGNIFICANCE OF THE PARK.....................................................1 PURPOSE AND SCOPE OF THE PLAN .....................................................................2 MANAGEMENT PROGRAM OVERVIEW................................................................8 Management Authority and Responsibility...................................................................8 Park Management Goals ..............................................................................................9 Management Coordination...........................................................................................9 Public Participation....................................................................................................10 Other Designations ....................................................................................................10 RESOURCE MANAGEMENT COMPONENT INTRODUCTION ........................................................................................................11 RESOURCE DESCRIPTION AND ASSESSMENT ..................................................12 Natural Resources......................................................................................................12 Topography...........................................................................................................12
    [Show full text]
  • September 15Th Make Those Tops and I'll See You at the with a Vacuum Hub Demo
    Finger Lakes Woodturners A Chapter of The American Association of Woodturners Presidential Mum- Again this year we will be making tops for blings—Sept 2016 the Golisano Children's Hospital and Hillside Center. I hope to see tops at every I hope everyone had a meeting since our goal again this year is great summer and got in 600 tops. I know we can do it. If anyone at least a little turning. I needs help or instructions, ask a mentor or myself didn't get in too fellow Club member; that's what we are much turning what with a here for. trip to Alaska and one to Dues will remain the same, $20 single or Gary Russell Maine. Wouldn't have missed it though. Now it is $30 family with students remaining time to get serious with my turning and free. Since this is our primary source of Club business. income, please sign up early. We have been very fortunate to be able to keep This year should be another good year for dues the same over the last several years the Club with a full lineup of demonstrators and still be able to provide talented Nation- and two national speakers/demonstrators- al turners at a reasonable cost. Mark Sillay and John Beaver. Dave Gil- bert will start us off on September 15th Make those tops and I'll see you at the with a Vacuum Hub Demo. See our web- meeting site for a full list of other events and FLWT meetings are held from 6:45 to 9:00 PM (pre-meeting Show and Share starts at 6:00 PM) on the 3rd Thursday of the dates.
    [Show full text]