DOCSLIB.ORG

Steel & Iron Production Facilities

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Steel & Iron Production Facilities STEEL & IRON PRODUCTION FACILITIES REPORT DATE: January 09, 2020 NUMBER OF FACILITIES: 43 TOTAL FULL-TIME EMPLOYMENT: 6,378 300 W. Broadway ● Frankfort, KY 40601 | (800) 626-2930 ● ThinkKentucky.com Steel Iron Production Industries Report Introduction and Methodology The Kentucky industry reports provide a list of facilities (with 10 or more employees) normally associated with Cabinet programs. Most information is taken directly from surveys completed by each facility or from phone or personal contact with the facility. Survey information is collected on an annual basis. Facility name, address, location, product or service, employment and other information may change and often does change between annual surveys. While all attempts are made to capture ongoing changes from data provided by facilities, local economic development contacts, media announcements, and Cabinet programs, no guarantee can be made that changes will be discovered. Also included on these reports, but not counted in the total number of facilities or full-time employment, are new location projects recently announced in Kentucky. The projects are identified by (announced) next to their projected full-time employment. Disclaimer The information provided herein by the Kentucky Cabinet for Economic Development is believed to be accurate but is not warranted and is for informational purposes only. While all attempts are made to insure the correctness and accuracy of information in this report and to make corrections and change errors brought to our attention, no representation or guarantee, express or implied, is made as to the accuracy of the information presented. Any information provided in this report is provided without assurances or warranties and should not be relied upon as fact. The Kentucky Cabinet for Economic Development assumes no liability for the accuracy of the information contained in this report. Alabama Wire Products Inc Cardinal Manufacturing Co 1100 West Park Road 225 Eiler Ave Elizabethtown, KY 42701 Louisville, KY 40214-2924 Phone: 270-737-6581 Phone: 502-363-2661 www.sswholding.net www.cardinalmfg.com Drawn wire for refrigerator shelving, oven racks, and modular Steel, bronze, brass & aluminum roll formed metal products & parts storage racks; supplier of coil-based wire and welded wire Full-time Employment: 56 reinforcing mesh. (2018) Established: 1958 Full-time Employment: 56 (2018) NAICS Codes: 331221, 331420, 332322 Established: 2005 NAICS Codes: 331222 Contact: Mr. Eric Weisbach, Prdtn/Ops Exec Contact: Mr. Todd Seger, Genl Mgr CC Metals & Alloys LLC American Building Components 1542 North Main St Calvert City, KY 42029-9251 6975 Danville Rd Phone: 270-395-7631 Nicholasville, KY 40356-9594 www.ccmetals.com Phone: 859-887-4406 Ferro alloys (metal) production & warehouse distribution www.abcmetalroofing.com/abcroofing Full-time Employment: 135 Metal building products (2018) Established: 1949 Full-time Employment: 26 (2018) NAICS Codes: 331110, 541614 Established: 1991 NAICS Codes: 331221, 423510 Contact: Mr. Motti Korf, CEO Contact: Mr. Jack Bell, Plant Mgr Clementsville Fabricating American Highway Fence 12441 KY 70 Liberty, KY 42539 220 Midland Trail Industrial Park Phone: 606-782-7455 Mt. Sterling, KY 40353 www.tarterusa.com Phone: 859-498-3658 Fabricating - hardware fabrication, for gate components (hinges, www.highwayfenceusa.com hinge pins, braces) Fencing materials Full-time Employment: 20 (2018) Full-time Employment: 4 (2018) Established: 0 Established: 1997 NAICS Codes: 331222 NAICS Codes: 331222 Contact: Mr. Travis Cox, VP/Genl Mgr Contact: Mr. Robert Reynolds, Pres CONTECH Engineered Solutions LLC Bekaert Corporation 700 Tech Dr 2000 Isaac Shelby Dr Winchester, KY 40391-9662 Shelbyville, KY 40065-9129 Phone: 859-744-3339 Phone: 502-633-6722 www.conteches.com www.bekaert.com Steel retaining sheets & multiplate bridge planks. Galvanized Preformed steel staple wire, stitching wire, flat wire, polymer structural steel & aluminum drainage & bridge products & retaining extruded wire, tin plated wire and galvanized wire walls Full-time Employment: 134 (2018) Full-time Employment: 80 (2018) Established: 1990 Established: 1985 NAICS Codes: 331222 NAICS Codes: 331221 Contact: Mr. Michael Brown, Product Mgr Contact: Ms. Margurite Thomas, HR Mgr Bilstein Cold Rolled Steel LP Dafco Aerospace 3250 Spring Hollow Avenue 4830 Crittenden Dr Bowling Green, KY 42104 Louisville, KY 40209 Phone: 270-908-4906 Phone: 502-361-8826 www.bilstein-north-america.com www.dameron.net Cold rolled steel production mill Investment casting foundry Full-time Employment: 72 (2018) Full-time Employment: 45 (2017) Established: 2017 Established: 2011 NAICS Codes: 331110 NAICS Codes: 331512, 331513 Contact: Mr. Mark J Loik, Pres/CEO Contact: Mr. John Dameron, CEO 1/9/2020 Page 1 of 5 Dafco Inc Fritz Winter Div Dameron Alloy Foundries Fritz Winter Drive Franklin, KY 42134 6851 Cane Run Rd Louisville, KY 40258-2845 Phone: Phone: 502-933-9311 Automotive supplier, Foundry www.dameron.net Full-time Employment: N/A Investment castings foundary Established: 2017 Full-time Employment: 40 (2017) NAICS Codes: 331511 Established: 1994 Contact: NAICS Codes: 331512, 331513 J R Hoe & Sons Inc Contact: Mr. John Dameron, CEO N 19th St Dahl & Groezinger Inc Middlesboro, KY 40965 940 W 9th St Phone: 606-248-5560 Owensboro, KY 42301-2001 www.jrhoe.com Phone: 270-684-1404 Iron castings, gray and ductile; pattern tooling services; CNC www.dahlandgroezinger.com machined castings; prototypes; metal fabrications-steel, stainless & aluminum; AISC structural & miscellaneous; autoCAD design & Scrap iron, ferrous & nonferrous metal processing, export scrap. engineering. Also downspout boots and cast iron bollards. Full-time Employment: 20 (2018) Full-time Employment: 61 (2018) Established: 1885 Established: 1909 NAICS Codes: 331420, 331511, 423930 NAICS Codes: 331511, 332312, 332710, 332721 Contact: Mr. Drew Kirkland, Pres Contact: Mr. Harry H. Hoe, Pres Drill Steel Service Inc JMS Russel Metals Corp 4898 Highway 15 1455 Bloom Ave Whitesburg, KY 41858-8582 Paducah, KY 42001-7058 Phone: 606-633-4492 Phone: 270-575-0308 Steel rods, overcast, mandoors and other metal products. www.jmsmetal.com Distributes cutting bits & roof bolt products Metal sales, processing, distributing & light manufacturing, mainly Full-time Employment: 11 (2018) sawing & burning Established: 1983 Full-time Employment: 42 (2017) NAICS Codes: 331110 Established: 1999 Contact: Mr. Jamey Hylton, Pres NAICS Codes: 331221 Felker Brothers Corp Contact: Mr. Dan Bailey, Regl Mgr 125 Beaver Trail Road Ken-Tron Mfg Inc Glasgow, KY 42141-1273 610 Industrial Dr Phone: 270-678-4143 Owensboro, KY 42301-0187 www.felkerbrothers.com Phone: 270-684-0431 Stainless steel pipe, stainless steel pipe and tube 2" thru 24" in www.ken-tron.com diameter. Wire drawing & precision stampings for aerospace, electronics, Full-time Employment: 87 (2018) battery, medical, automotive and television products. Established: 1993 Full-time Employment: 60 (2018) NAICS Codes: 331221 Established: 1960 Contact: Mr. Gary Hartell, Plant Mgr NAICS Codes: 331222, 332119 Ferrous85" Company Contact: Mr. Robert Hudson, Chairman Gonzalez Enterprises, LLC MST Steel Corporation of Kentucky 100 Steel Plant Road 860 Withrow Ct Wilder, KY 41071 Bardstown, KY 40004-4100 Phone: 859-261-6161 Phone: 502-350-4100 www.ferrous85.com www.mststeel.com Steel toll processor of rolled steel Slitting & cold-reduction of steel coil Full-time Employment: 11 (2018) Full-time Employment: 15 (2018) Established: 2011 Established: 2001 NAICS Codes: 331110 NAICS Codes: 331110, 493110 Contact: Mr. Eduardo Gonzalez, Pres Contact: Mr. Richard Thompson, Pres 1/9/2020 Page 2 of 5 Mubea Inc Nucor Steel Gallatin 6800 Industrial Rd 4831 US Highway 42 West Florence Campus Operations Ghent, KY 41045 Florence, KY 41042 Phone: 859-567-3100 Phone: 859-746-5300 www.nucorsteel.com www.mubea.com Flat rolled steel coils Automotive component parts (springs, hose clamps, stabilizer bars) Full-time Employment: 464 (2018) Full-time Employment: 1,017 (2018) Established: 1993 Established: 1982 NAICS Codes: 331110, 331221 NAICS Codes: 331221, 332613, 336390 Contact: Mr. John Farris Contact: Mr. Doug Cain, CEO Nucor Tubular Products Mubea Precision Springs Inc 7301 Logistics Drive 8252 Dixie Hwy Louisville, KY 40258 Florence, KY 41042 Phone: 800-840-8823 Phone: 859-746-5300 http://www.nucortubular.com/ www.mubea.com Domestic producer of EMT, IMC, and rigid electrical steel conduit; Manufacturer of transmission springs and hose clamps ISO 9001:2008, ISO 14000, ISO 18000 and UL certified company. Full-time Employment: 317 (2018) Full-time Employment: 217 (2018) Established: 2009 Established: 2006 NAICS Codes: 331210, 336350 NAICS Codes: 331210 Contact: Mr. Christian Hesener, Genl Mgr Contact: Mr. Douglas Jellison, Pres Nisshin Automotive Tubing LLC Plymouth Engineered Shapes 107 Fieldview Drive Div Plymouth Tube Co Versailles, KY 40383-1532 201 Commerce Ct Phone: 859-879-6067 Hopkinsville, KY 42240-9200 Stainless steel automotive tubing Phone: 270-886-6631 Full-time Employment: 27 (2018) www.plymouth.com/extrusions Established: 2005 Stainless, carbon & alloy steel extrusions; special & structural titanium & nickel base shapes NAICS Codes: 331210 Full-time Employment: 122 (2018) Contact: Mr. Satoshi Steve Migita, Pres Established: 1980 North American Stainless NAICS Codes: 331221, 331491, 332510 6870 Highway 42 E Contact: Mr. David Crouch, Genl Mgr Ghent, KY 41045-9615 Phone: 502-347-6000 Precision Strip Inc www.northamericanstainless.com
Load more

Recommended publications
  • NUCOR Steel-Hertford's Petition to Intervene
    Velson Mullins NelsonMullin sRile y& Scarborough LLP Attorneys and Counselors at Law Joseph W. Bason 4140 Parklake Avenue / GlenLake One / Second Floor / Raleigh. North Carolina 27612 Tel: 919.877.3807 Tel: 919.877.3800 Fax: 919.877.3799 Fax: 919.877.3140 www.nelsonmullins.co m [email protected] April 28,201 0 VIA HAND DELIVERY Ms. Renne Vance APR282Dtt North Carolina Utilities Commission ' ClericsOftc * 430 N. Salisbury Street 5th Floor- Clerks Office Raleigh,N C 27699-4325 Re: Inth e Matter of Application of Virginia Electric and Power Company, d/b/a Dominion North Carolina Power, for Authority to Transfer Functional Control of Transmission Assets to PJM Interconnection, LLC (NCUC, Docket No. E-22, Sub 418) Our FileNo . 19128/01513 Dear Ms. Vance: r^ Enclosed for filing on behalf of Nucor Steel-Hertford ("Nucor") are an original and thirty (30) vUt/lCJ copies ofNucor' s Petition to Intervene relating to the above-referenced matter. 96 n/Tllflffi ^•^so enc^ose^ IS an additional copy of thedocumen t to bestampe d as "filed" and returned to me ' . ," viam y courier. ( V11lO J Thank you for your assistance in this,matter . With best regards, Ia m \)j0^-^ ' Very truly yours, h W. Eason 36rtC5> JWE:nwilmot <c>O^JPp^nc*0Sures 7^ \rv\ cc: A^ parties of record (w/enc.) /ADA -PlAUptlanta • ^s*011 *Charlesto n • Charlotte • Columbia • Greenville • Myrtle Beach • Raleigh • Washington, DC • Winston-Salem •aaiito STATE OF NORTH CAROLINA UTILITIES COMMISSION RALEIGH APR282M DOCKET NO. E-22,Su b 418 CteriteOffic e BEFORE THE NORTH CAROLINA UTILITIES COMMISSION ^UfiBiesCommission In the Matter of ) Application of Virginia Electric and ) NUCOR STEEL-HERTFORD'S Power Company, d/b/a Dominion North ) PETITION TO INTERVENE Carolina Power, for Authority to Transfer ) Functional Control ofTransmissio n ) Assets to PJM Interconnection, LLC ) Pursuant to Rules Rl-17 of the Rules of Practice and Procedure of the North Carolina Utilities Commission, Nucor Steel-Hertford, a division of Nucor Corporation ("Nucor"), hereby moves to intervene in the above-captioned proceeding.
    [Show full text]
  • 60 August 3, 2021 Page 1 of 6
    QUALIFIED PRODUCT LIST 60 August 3, 2021 Page 1 of 6 SOUTH CAROLINA DEPARTMENT OF TRANSPORTATION Qualified Suppliers of Reinforcing Steel These Producers are qualified in accordance with SCDOT Qualified Product Policy 60. Trade names are registered trademarks of the appropriate company. SCDOT Producer Contact /Telephone PRODUCER CODE SteelRebarCo005 CMC Steel South Carolina Richard Ray (CMCCSC) 310 New State Road (803) 936-3901 Cayce, SC 29033 [email protected] SteelRebarCo029 CMC Steel Oklahoma Robbie Booth (CMCDOK) 584 Old Highway 70 (480) 396-7127 Durant, OK 74702 [email protected] SteelRebarCo002 CMC Steel Florida Alex Renosto (CMCJFL) 16770 Rebar Road (904) 266-1468 Jacksonville, FL 32234 [email protected] SteelRebarCo003 CMC Steel Tennessee Jim Hall (CMCKTN) 1919 Tennessee Avenue (865) 202-5972 Knoxville, TN 37921 [email protected] SteelRebarCo033 CMC Steel Mesa Jacob Selzer (CMCMAZ) 11444 East Germann Road (480) 396-7101 Mesa, AZ 85242 [email protected] SteelRebarCo017 CMC Steel New Jersey Joe Homic (CMCSNJ) 1 North Crossman Road (800) 721-8047 Sayreville, NJ 08872 [email protected] SteelRebarCo022 CMC Steel Texas Jason Dinscore (CMCSTX) 1 Steel Mill Drive (830) 372-8746 Seguin, Texas 78155 [email protected] SteelRebarCo023 CMC Steel California Michael Mayer (CMCRCCA) 12459-B Arrow Road (909) 646-7886 Rancho Cucamonga, CA 91739 [email protected] SteelRebarCo021 Evraz Rocky Mountain Steel Billy Byrd (EVRAZCO) 2100 South Freeway (719) 561-6426 Pueblo, CO 81004 [email protected] SteelRebarCo001 Gerdau Ameristeel (Charlotte Mill) Rachel Warren (GACNC) 6601 Lakeview Road (704) 596-0361 Ext. 3039 Charlotte, NC 28269 [email protected] SteelRebarCo019 Liberty Steel Tyler Higgins (LSPIL) 7000 S.W.
    [Show full text]
  • Brief on Exceptions of Nucor Steel Auburn, Inc
    STATE OF NEW YORK PUBLIC SERVICE COMMISSION CASE 03-E-0188 - Proceeding on Motion of the Commission Regarding a Retail Renewable Portfolio Standard. BRIEF ON EXCEPTIONS OF NUCOR STEEL AUBURN, INC. Overview The Recommended Decision (“RD”) issued on June 3, 2004, culminates a fifteen month effort to assess the practical ramifications of a Commission policy to spur development of renewable resources to serve New York’s growing electric load. As described in the Introduction and Background section to the RD, mounting state concerns regarding the environmental costs of fossil-fired generation (particularly air emissions) and growing dependence on natural-gas fired generators are the prime motivators for more aggressive pursuit of “clean” energy resources. This interest in renewable, low-emitting or non-emitting resources is inextricably linked to New York’s policies to promote economic development. As Chairman Flynn remarked in his address to the Center for Business Intelligence forum on New York Power Supply in New York City on June 11, 2004: From Clean-Fueled vehicle programs designed to encourage development of cleaner transportation technologies and alternative fuels, to Executive Order lll’s call for more efficient and cleaner use among state-owned facilities, to tax credits that encourage construction of “green” buildings, Governor Pataki has developed a comprehensive energy agenda that balances the need for more energy resources with the need to protect our environment and encourage economic development. The Governor has consistently emphasized the importance of energy’s role in linking environmental protection with economic development.1 Nucor Steel Auburn, Inc. (“Nucor”) has been an active participant in this docket.
    [Show full text]
  • Nucor VR16 II™ Nucor VR16 II™ Vertical Rib Standing Seam Roof System
    VERTICAL RIB STANDING SEAM ROOF SYSTEM Nucor VR16 II™ Nucor VR16 II™ Vertical Rib Standing Seam Roof System The Nucor Building Systems VR16 II-90 and VR16 II-360 Roof Systems are structural standing seam vertical rib roof panels that are perfect for architectural requirements in today’s marketplace. The seaming methods used in the VR16 II-90 and VR16 II-360 roof panels offer an attractive architectural system available both in Galvalume® and PVDF finishes as standard. Panels are installed with concealed fastener clips allowing for thermal movement, and mechanically seamed. VR16 II-90 Roof System Nucor VR16 II-90 Roof System panel uses a weathertight 90-degree seam for a battened architectural aesthetic ideal for buildings with various roof conditions including hips and valleys, and easily accommodates complex roof geometries. VR16 II-360 Roof System The VR16 II-360 Roof System features a full 360-degree rolled seam. With uninterrupted linear roof lines, VR16 II-360 offers an even greater level of architectural design to provide a sleek, modern appearance. Designed to withstand the most extreme weather conditions, it offers exceptional performance and weathertightness. Nucor VR16 II Warranties • 25 Year Galvalume Finish • 35 Year PVDF Paint Finish • 20 Year Weathertightness For specific details, please refer to the Warranty Guide online at www.nucorbuildingsystems.com Galvalume® is a registered trademark of BIEC International, Inc. Product Specifications & Details Product Specifications • Rib height: 2″ • Cover width: 16″ • Factory sealant applied along female rib • Minor striations to help reduce “oil canning” • Galvalume or painted PVDF finishes • Standard 24 ga. material (22 ga.
    [Show full text]
  • News Release
    News Release Nucor Breaks Ground on Kentucky Plate Mill BRANDENBURG, KENTUCKY, October 23, 2020 – Nucor Corporation, Kentucky state officials, and local government leaders held a groundbreaking today for the company’s new steel plate mill in Brandenburg, Kentucky. The new $1.70 billion plate mill will create more than 400 full-time jobs and be fully operational in 2022. “We are very excited to begin construction on our new plate mill in Kentucky. This state-of-the-art mill will make us a market leader in steel plate products,” said Leon Topalian, President & CEO of Nucor Corporation. “We have been doing business in Kentucky for over a decade and have benefited from the strong business climate and great local workforce.” When the mill is completed, Nucor will have the ability to produce 97 percent of the steel plate products consumed in the U.S. market. The location on the Ohio River will give Nucor transportation advantages in serving the Midwest plate market, which is the largest plate-consuming market in the U.S. “The new plate mill helps us advance our goal of expanding our product portfolio, particularly growing our production of value-added plate products. When it is completed and operational, we’ll be one of only two companies that can produce essentially all of the plate sizes consumed in the U.S. today,” said Al Behr, Executive Vice President of Plate & Structural Products. Nucor operates more than 15 facilites in the state and employs over 2,000 teammates. In addition to the new plate mill, Nucor has invested more than $800 million in its steel sheet mill in Ghent to add a new galvanizing line and expand the production capacity of the mill – a project that is expected to be completed by the middle of next year.
    [Show full text]
  • The FOCUS® of Nucor Building Systems
    The FOCUS® of Nucor Building Systems Nucor Building Systems entered the metal building industry in 1987, with our first full service plant in Indiana. Our goal was to deliver performance and value. Our FOCUS statement commits that we will concentrate on the things that matter most to our customers. Far more than a marketing acronym, the FOCUS statement is comprised the fundamental principles that drive our business behaviors every day. Every NBS employee understands the value of executing on these commitments. Fit Steel that fits. When you buy a car you expect it to start, and when you buy a building you expect it to fit…simple as that! Our greatest source of pride comes from jobs that ship with no back charges, back orders, or shortages. On Time Deliveries You get commitments that mean something with Nucor Building Systems. Whether it’s a small, single truck shipment or a large multi-phase job, we make sure that you have erectable steel based on your construction schedule. We will coordinate primary and secondary framing, sheeting, crane steel, bar joists, and trim to make sure you can actually build what we send. Competitive Pricing Nucor Building Systems has consistently led the industry in man-hours-per-ton in both production and design, making us one of the most efficient manufacturers and low cost suppliers in the industry. Our advanced computer pricing system is available to every Nucor Builder, offering the convenience of pricing many buildings in his/her own office with flexibility, speed, and significant design breadth. Unbeatable Service Since Nucor Building Systems utilizes support material produced by our own Nucor Steel divisions, we can assure a predictable supply of raw materials.
    [Show full text]
  • By Nucor Steel— 1
    BEFORE THE BEFORE THE CO PUBLIC SERVICE COMMISSION OFSOUTHOF SOUTH CAROLINA ,L-} DOCKET NO. 2006-1-E DOCKET NO. 2006-1-E ,,i ,'} .... ' , 4, r. L IN THE MATTER OF:OF ) ) t%,._,.,) ' Carolina Power &8 Light Company d/b/a ) PETITION TO INTERVENE _i ,..,,j Progress Energy Carolinas, Inc. ) BY NUCOR STEEL-STEEL— Annual Review of Base Rates for ) SOUTH CAROLINA Fuel Costs ) Nucor Steel-South Carolina ("Nucor"),("Nucor"), a Division of Nucor Corporation, pursuant to Rule 103-836 of the rulesrules and regulations of thethe South Carolina Public Service Commission ("Commission"),("Commission" ), hereby respectfully petitions to intervene in the above-captioned docket. Nucor states the following grounds in support of this petition: 1. Nucor owns and operates a steel production facilityfacility near Darlington, South Carolina. As a retail customer of Progress Energy Carolinas, Inc.Inc. ("Progress("Progress Energy")Energy" ) (formerly(formerly known as Carolina Power & Light Company ("CP&L")',),("CP8L")), Nucor purchases hundreds of millions of kWh of electricity annually at a cost of millions of dollars a year. Since thethe cost of electricity comprises one of the major costs of Nucor's manufacturing process, electric costs directly affect Nucor's ability to continue to produce steel at a competitive price. 2. This docket has been established to review Progress Energy's historical and projected fuel costs and to determine thethe appropriate fuel factor for the next twelvetwelve months. Nucor isis concerned about the impactimpact of Progress Energy's fuel costs on its rates and those of other customers. Nucor has a stake in, and will be directly and substantially affected by, thethe outcome of this proceeding.
    [Show full text]
  • The Partnership of Nucor and Danieli Teams Will Bring the Gallatin Casting and Rolling Plant to the Next Level of High-Quality Production and Competitiveness
    The partnership of Nucor and Danieli teams will bring the Gallatin casting and rolling plant to the next level of high-quality production and competitiveness. This is the first time that a classical compact thin slab casting and rolling plant is fully reconfigured into an ultra-modern QSP® (Quality Strip Production) plant. Both Nucor and Danieli teams are committed to set a new benchmark in Casting and Rolling Technology. Formerly known as the Gallatin Steel Company, the thin slab rolling plant located in Ghent, KY has a name plate capacity of 1.6 million shTPY of hot rolled coils having a thickness range from 1.4 to 12.7 mm, widths up to 1,625 mm and maximum coil weight of 35 shTon. The existing plant operates a 185 t twin shell DC EAF, a single LMF, a vertical caster, 206 m tunnel furnace, a six-stand close-coupled rolling mill, traditional laminar cooling and one down coiler. The current capabilities of the steel plant are mostly structural steel, micro-alloyed grades and thin line pipe grades. Like similar compact plants, Gallatin was originally designed for doubling the annual capacity by means of a second meltshop, second vertical caster and tunnel furnace connected by a swivel ferry system to the in-line HSM. The new equipment was originally meant to be a copy of the existing one. In October 2014, Nucor became the owner of the Gallatin Steel Company and has recently approved an investment to advance the technological capabilities and competitiveness of the Nucor Steel Gallatin Sheet Mill. Danieli is the selected technology supplier for the complete equipment and automation system, from raw materials to hot rolled coil.
    [Show full text]
  • Nucor DRI Facility St
    CASE STUDY Nucor DRI Facility St. James Parish, Louisiana PROJECT PARTNERS Owner Nucor Corporation – Charlotte, NC General Contractor Massmann Construction Co. – Kansas City, KS PRODUCTS Pipe Pile: 18” to 96” OD x 80’ to 115’ PROJECT TIME FRAME May 2011 to April 2012 HISTORY to be transported to the steel mills easily and needed for many stages of this construction Nucor Corporation, the largest steel company efficiently. Once a suitable site was identified, a project. in the United States, was looking for a way dock needed to be built that could handle the to increase its competitive advantage in the building materials for the plant, as well as the Nucor Skyline was able to use the steel coil industry. One way was to invest in a direct iron outflow of materials once production began. produced in Nucor’s Decatur, AL facility and ore reduction facility. This process involves transport it by barge to the Skyline facility in converting natural gas and iron ore pellets SOLUTION Iuka, MS. At this plant, the coil was rolled into into high-quality DRI (direct-reduced iron), The construction of a barge loading/unloading the proper-sized pipe, ranging from 18” to which is the raw material used by Nucor’s steel dock facility on the Mississippi River was 96” for the project. The pipe was needed in mills. Not only does this process employ the needed. The facility offloads ocean going ships lengths varying from 160 to 230 feet, and was latest technologies to reduce emissions, but loaded with iron ore. The iron ore is transferred produced in half-lengths, and barged from the it also provides a low-cost environment and to a processing plant on land by a conveyor Iuka plant to a vendor in New Orleans where operational flexibility.
    [Show full text]
  • Petition to Object to the Nucor Steel Facility, St. James Parish, Louisiana
    BEFORE THE ADMINISTRATOR U.S. ENVIRONMENTAL PROTECTION AGENCY In the Matter of Louisiana Department of Environmental Quality's Proposed Operating Permit and Prevention of Significant Deterioration Permit for Consolidated Environmental Management, Inc./Nucor Steel, Louisiana, St. James Parish, Louisiana LDEQ Agency Interest No. 157847 Activity Nos. PER2008000 1 and PER20080002 Permit Nos. 2560-00281-VO; PSD-LA-740 Proposed to Nucor Steel, Louisiana By the Louisiana Department of Environmental Quality on October 15 ,2008 PETITION REQUESTING THAT THE ADMINISTRATOR OBJECT TO THE TITLE V OPERATING AND PREVENTION OF SIGNIFICANT DETERIORATION PERMITS PROPOSED FOR NUCOR STEEL, LOUISIANA Pursuant to Section 505(b) of the Clean Air Act, 42 U.S.C. § 7661 deb )(2) and 40 C.F.R. §70.8( d) , Zen-Noh Grain Corporation ("Zen-Noh") petitions the Administrator of the U.S. Environmental Protection Agency ("Administrator") to object to Title V Air Operating Permit (No. 2560-00281 -VO) ("Operating Permit"). Zen-Noh also petitions the Administrator to reopen or revise Prevention of Significant Deterioration Permit (No. PSD-LA-740) ("PSD Pennit"). And, Zen-Noh petitions the Administrator to direct Louisiana Department of Environmental Quality ("LDEQ") to provide Zen-Noh and the public with all information necessary to the issuance or denial of the Operating Pennit and PSD Permit, provide a meaningful period for public review, and reopen the public comment period. Both the Operating Permit and PSD Permit were proposed on or about October 15, 2008 by LDEQ for issuance to Consolidated Environmental Management, Inc.INucor Steel Louisiana ("Nucor") for a Pig Iron Manufacturing Plant in St. James Parish, Louisiana.
    [Show full text]
  • 2019 Recycled Steel Content of Nucor Products (% by Total Weight) Total
    NUCOR CORPORATION 1915 Rexford Road Charlotte, NC 28211 704.366.7000 July 2020 To: All Nucor Customers Re: 2019 Recycled Content of Nucor Steel Mill Products Nucor Corporation is North America’s largest recycler, using approximately 20.0 million net tons of scrap steel in 2019 to create new products. Nucor uses Electric Arc Furnace (EAF) technology at all of its steel recycling facilities. EAFs use post-consumer scrap steel material as the major feedstock, unlike blast furnace operations that use mined iron ore as the major feedstock. Nucor has prepared the following information to help calculate the recycled content for products being used in “Green Building” applications or for projects in the LEED® certification program. These percentages are based on the total weight of the products. The calculations are based on 2019 scrap steel delivered and hot metal tons produced and are defined in accordance with ISO 14021:2015. More specific product information may be available from facility representatives. You can find the division contact information here – Nucor LEED Contacts (PDF). Recycled Content – LEED 2009 MR 4; LEED v4 MR Credit: Sourcing of Raw Materials 2019 Recycled Steel Content of Nucor Products (% by Total Weight) Product Group Average Recycled Content Nucor Bar Products 97.0% Nucor Engineered Bar Products 85.5% Nucor Beam Products 79.7% Nucor Plate Products 60.5% Nucor Sheet Products 55.8% Nucor Castrip® 83.5% Total Nucor Steel Combined 70.9% Vulcraft Structural Products 97.0% www.nucor.com NUCOR CORPORATION 1915 Rexford Road Charlotte, NC 28211 704.366.7000 Vulcraft / Verco Decking 55.8% Nucor Grating / Fisher-Ludlow Grating 97.0% Nucor Building Group 70.9% Harris Rebar 97.0% Nucor Fastener Products 97.0% Nucor Wire Products 97.0% Nucor Cold Finish 85.5% Bar Mill Group – The Nucor Bar Mill Group produces rebar, angles, flats, rounds and other miscellaneous structural and non-structural shapes.
    [Show full text]
  • Steel in Transition New Capacity, Trade, Transportation & Forecasts
    AUGUST 26-28, 2019 SMU STEEL SUMMIT 2019 Georgia International Convention Center Atlanta, GA SteelMarketUpdate.com/Events/Steel-Summit STEEL IN TRANSITION NEW CAPACITY, TRADE, TRANSPORTATION & FORECASTS CONFERENCE AGENDA Monday, August 26, 2019 10:00 - 5:30 PM Conference Registration Georgia International Convention Center – South Lobby All-Day Beverage - Sponsored by: BMO Harris Bank 10:30 - 12:00 PM Price Risk Management Workshop Hosted by CME Group 10:30 - 10:45 General Introduction to futures markets 10:45 - 11:15 Hedging examples from consumer and producer perspectives 11:15 - 11:55 Panel discussion - development and status of the steel futures market 11:55 –-Q&A Andre Marshall, CEO and Founder, Crunch Risk Guarav Chhibbar, Partner, Metal Edge Partners Jeremy Flack, CEO, Flack Global Metals Sean Kessler, Manager - Metals Products, CME Group Only this event will be held at the Airport Marriott Gateway Hotel. All other events will be held at the GICC. 1:00 - 1:45 PM SMU/CRU Proprietary Indices & Forecasts John Packard, President & CEO Steel Market Update Chris Houlden, Research Manager – Steel and Head of Prices Development CRU Josh Spoores, Principal Analyst - Steel CRU 1:45 - 2:30 PM Transportation Issues & Solutions James Burg, President James Burg Trucking Company JR Schaaf (Jim), Group VP - Metals & Construction Norfolk Southern 2:30 - 2:50 PM Break - Sponsored by: Acero Prime 2:50 - 4:00 PM Steel Distribution & Processing: Demand Perspectives Edward J. Lehner, President & CEO Ryerson John G. Reid, Director, President & CEO Russel
    [Show full text]