DOCSLIB.ORG

Alloy - Electrical Properties Electrical Resistivity Temperature Coefficient Mohmcm K-1

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Alloy - Electrical Properties Electrical Resistivity Temperature Coefficient Mohmcm K-1 Goodfellow Cambridge Limited Ermine Business Park, Huntingdon PE29 6WR England Telephone 0800 731 4653 : Fax 0800 328 7689 Alloy - Electrical Properties Electrical resistivity Temperature coefficient mOhmcm K-1 Alloy 825 131 - Ni39.5/Fe32/Cr22/Mo 3/Cu 2/ Ti Aluchrom O1 - Resistance 135-145 0.00007 Alloy Fe70/Cr25/Al 5 Aluminium alloy 2011 4.5 - Al93/Cu 5.3/Fe 0.7/Si 0.4/Pb 0.3/B Aluminium alloy 6061 3.9-4.1 - Al97.5/Mg 1/Si 0.6/Fe 0.5/Cu 0.4 Aluminium alloy 6082 3.8 - Al97.4/Si 1/Mg 0.9/Mn 0.7 Aluminium alloy 7075 5.15 - Al90/Zn 5.5/Mg 2.5/Cu 1.5/Si 0.5 Aluminium alloy EN AC 4 - 42100 Al 91.7/Si 7/Mg 0.3 Aluminium/Magnesium/ 5.1 - Manganese/Chromium Al96.45/Mg 2.6/Mn 0.8/Cr 0.15 Aluminium/Magnesium/ 3.4-3.8 0.0030 Silicon Al98/Mg 1/Si 0.6 Aluminium/Magnesium/ 3.4-3.8 0.0031-0.0035 Silicon Al98/Mg 1/Si 1 Aluminium/Magnesium/ 3.2 - Silicon Al99/Mg 0.5/Si 0.5 Aluminium/Magnesium 5.6-6.1 0.0020 Al95/Mg 5 Aluminium/Magnesium 4.5-5.7 0.0019-0.0026 Al97/Mg 3 Aluminium/Magnesium 4.95 - Al97.5/Mg 2.5 Aluminium/Silicon/ 3.8 - Magnesium/Manganese Al97.5/Si 1.0/Mg 0.8/Mn 0.7 Aluminium/Silicon 5.56 - Al88/Si12 All information and technical data are given as a guide only. Although every effort has been made to ensure that the information 1 is correct, no warranty is given as to its completeness or accuracy. 17-September-2021 Goodfellow Cambridge Limited Ermine Business Park, Huntingdon PE29 6WR England Telephone 0800 731 4653 : Fax 0800 328 7689 Alloy - Electrical Properties Electrical resistivity Temperature coefficient mOhmcm K-1 Aluminium/Silicon 2.6-3.5 0.0042 Al99/Si 1 Antimonial Lead 24.0 - Pb96/Sb 4 Bismuth/Lead 43.0 - Bi55.5/Pb44.5 Brass 6.2-6.6 0.0016-0.0017 Cu63/Zn37 Brass 6.2-7.8 0.0012-0.0016 Cu70/Zn30 Bronze 14-17 0.0006 Cu89/Sn11 Chromaloy O1 - Resistance 137 0.00007 Alloy Fe75/Cr20/Al 5 Cobalt/Chromium/Iron/ 95 - Nickel/Molybdenum/ Manganese Co40/Cr20/Fe15/Ni15/Mo 7/ Mn 2/C/Be Cobalt/Chromium/Tungsten/ 88.6 - Nickel/Iron/Manganese Co50/Cr20/W 15/Ni10/Fe 3/ Mn 2 Constantan - Resistance 52.0 +/-0.00002 Alloy Cu55/Ni45 Copper/Beryllium 5.4-11.5 0.0010-0.0018 Cu98/Be 2 Copper/Chromium/ 1-2 - Zirconium Cu98.9/Cr 1.0/Zr 0.1 Copper/Nickel 37.4 - Cu70/Ni30 Copper/Tellurium 1.92 - Cu99.5/Te 0.5 Dural1 - Aluminium/Copper/ 5.0 0.0022-0.0026 Magnesium Al95/Cu 4/Mg 1 Evanohm1 - Precision 134 0.00001 Resistance Alloy Ni75/Cr20/Al 2.5/Cu 2.5 All information and technical data are given as a guide only. Although every effort has been made to ensure that the information 2 is correct, no warranty is given as to its completeness or accuracy. 17-September-2021 Goodfellow Cambridge Limited Ermine Business Park, Huntingdon PE29 6WR England Telephone 0800 731 4653 : Fax 0800 328 7689 Alloy - Electrical Properties Electrical resistivity Temperature coefficient mOhmcm K-1 Fecralloy1 - Iron/Chromium 134 0.0001 Fe72.8/Cr22/Al 5/Y 0.1/Zr 0.1 Gilding Metal 4.6-5.4 0.0014-0.0016 Cu85/Zn15 Glass Sealing Alloy 48.9 0.0037 Fe54/Ni29/Co17 Gold/Nickel 15.5 - Au82/Ni18 Hastelloy1 B - Corrosion 137 - Resistant Alloy Ni62/Mo28/Fe 5/Cr/Mn/Si Hastelloy1 C276 - Heat 125-130 - Resisting Alloy Ni57/Mo17/Cr16/Fe/W/Mn Hastelloy1 X 118 - Ni49.5/Cr22/Fe18/Mo 9/Co 1/ W Havar1 - High-Strength Non- 92 - Magnetic Alloy Co42.5/Cr20/Ni13/Fe/W/Mo/ Mn Haynes1 230 alloy 125 - Ni62/Cr22/W 14/Mo 2 High Permeability Magnetic 55 - Alloy Ni80/Fe15/Mo 5 Incoloy1 alloy 800 - Heat 20 - Resisting Alloy Ni32.5/Cr21/Fe Inconel 6251 - Corrosion 129 - Resistant Alloy Ni61/Cr22/Mo 9/Fe 5 Inconel1 617 1.22-1.34 - Ni57/Cr22/Co12/Mo 9 Inconel1 alloy 600 - Heat 103 - Resisting Alloy Ni72/Cr16/Fe 8 Inconel1 alloy 718 - Heat 125 - Resisting Alloy Ni53/Fe19/Cr19/Nb/Mo/Ti Inconel1 X750 - Heat 122-124 - Resisting Alloy Ni74/Cr15/Fe 7/Ti/Al/Nb All information and technical data are given as a guide only. Although every effort has been made to ensure that the information 3 is correct, no warranty is given as to its completeness or accuracy. 17-September-2021 Goodfellow Cambridge Limited Ermine Business Park, Huntingdon PE29 6WR England Telephone 0800 731 4653 : Fax 0800 328 7689 Alloy - Electrical Properties Electrical resistivity Temperature coefficient mOhmcm K-1 Indium/Silver 7.5 - In97/Ag 3 Indium/Tin 15 - In50/Sn50 Invar1 - Controlled Expansion 75-85 - Alloy Fe64/Ni36 Iron/Chromium/Molybdenum 49.9 - Fe90/Cr 9/Mo 1 Iron/Nickel 44 - Fe50/Ni50 Iron/Nickel 49 - Fe52/Ni48 Iron/Nickel 45 - Fe55/Ni45 Iron/Nickel 68 - Fe58/Ni42 Leaded Brass 6.2 - Cu58/Zn39/Pb 3 Magnesium Alloy AZ61 12.5 - Mg93/Al 6/Zn 1 - - Magnetic Shape Memory 70 0.003 Alloy Ni50/Mn28/Ga22 (Atomic %) Magnetic Shielding Alloy 55-62 - Ni77/Fe14/Cu 5/Mo 4 Manganin1 - Resistance Alloy 43-48 0.00001 Cu86/Mn12/Ni 2 Molybdenum High 5.3-5.5 - Temperature Alloy TZM Mo99/Ti 0.5/Zr 0.1 Monel1 alloy 400 48-51 0.0019 Ni65/Cu33/Fe 2 Monel1 alloy K-500 61 - Ni63/Cu30/Al3/Fe2/Mn1.5/ Ti0.5 Neodymium/Iron/Boron 1.1-1.7 - Nd Fe B 2 14 Nickel Silver (18) 28.7 - Cu65/Ni18/Zn17 Nickel Silver 29 0.0003 Cu62/Ni18/Zn20 All information and technical data are given as a guide only. Although every effort has been made to ensure that the information 4 is correct, no warranty is given as to its completeness or accuracy. 17-September-2021 Goodfellow Cambridge Limited Ermine Business Park, Huntingdon PE29 6WR England Telephone 0800 731 4653 : Fax 0800 328 7689 Alloy - Electrical Properties Electrical resistivity Temperature coefficient mOhmcm K-1 Nickel Silver 130 - Cu64/Ni12/Zn24 Nickel/Beryllium/Titanium 43 - Ni97.5/Be 1.95/Ti 0.5 Nickel/Chromium 108 0.00005 Ni80/Cr20 Nickel/Copper 48 - Ni70/Cu30 Nickel/Iron 45 0.0034 Ni52/Fe48 Nickel/Iron 62 - Ni80/Fe20 OFHC Copper 1.70 0.0038-0.0039 OFHC Palladium/Silver 35 0.001 Pd75/Ag25 Permendur 491 40 - Co49/Fe49/V 2 Phosphor Bronze 11.0-16.0 0.0006-0.0007 Cu94/Sn 6 Platinum/Iridium 35 0.001 Pt70/Ir30 Platinum/Iridium 31-32 0.001 Pt75/Ir25 Platinum/Iridium 31-32 0.001 Pt80/Ir20 Platinum/Iridium 28.5-29.0 - Pt85/Ir15 Platinum/Iridium 25 0.0013 Pt90/Ir10 Platinum/Rhodium 17.5 0.0014 Pt60/Rh40 Platinum/Rhodium 18.8 0.0014 Pt70/Rh30 Platinum/Rhodium 19.0 0.0016 Pt87/Rh13 Platinum/Rhodium 18.4-19.2 0.0017 Pt90/Rh10 Platinum/Rhodium 19.2 0.0017 Pt94/Rh 6 All information and technical data are given as a guide only. Although every effort has been made to ensure that the information 5 is correct, no warranty is given as to its completeness or accuracy. 17-September-2021 Goodfellow Cambridge Limited Ermine Business Park, Huntingdon PE29 6WR England Telephone 0800 731 4653 : Fax 0800 328 7689 Alloy - Electrical Properties Electrical resistivity Temperature coefficient mOhmcm K-1 Platinum/Tungsten 62-68 0.00025 Pt92/W 8 Silver/Copper 2 - Ag72/Cu28 Silver/Palladium 14.84 - Ag70/Pd30 Stainless Steel - 15-7PH 80 - Fe/Cr15/Ni 7/Mo 2.25 Stainless Steel - 17-4PH 70-80 - Fe/Cr17/Ni 4 Stainless Steel - 17-7PH 80-85 - Fe/Cr17/Ni 7 Stainless Steel - AISI 301 70-72 - Fe/Cr17/Ni 7/C 0.1max Stainless Steel - AISI 302 70-72 - Fe/Cr18/Ni 8 Stainless Steel - AISI 303 72 - Fe/Cr18/Ni 9/Mn/Si Stainless Steel - AISI 304L 72 - Fe/Cr18/Ni10 Stainless Steel - AISI 304 70-72 - Fe/Cr18/Ni10 Stainless Steel - AISI 310 70-78 - Fe/Cr25/Ni20 Stainless Steel - AISI 316 70-78 - Fe/Cr18/Ni10/Mo 3 Stainless Steel - AISI 321 70-73 - Fe/Cr18/Ni 9/Ti Stainless Steel - AISI 347 70-73 - Fe/Cr18/Ni10/Nb Stainless Steel - AISI 410 56-72 - Fe/Cr12.5 Stainless Steel - AISI 420 55 - Fe86.7/Cr13.0/C 0.3 Stainless Steel - Duplex 80 - Fe/Cr22/Ni 5.5/Mo 3/N Sterling Silver 1.8 - Ag92.5/Cu 7.5 T1 - Thermocouple Alloy 70.6 0.00032 Ni90/Cr10 All information and technical data are given as a guide only. Although every effort has been made to ensure that the information 6 is correct, no warranty is given as to its completeness or accuracy. 17-September-2021 Goodfellow Cambridge Limited Ermine Business Park, Huntingdon PE29 6WR England Telephone 0800 731 4653 : Fax 0800 328 7689 Alloy - Electrical Properties Electrical resistivity Temperature coefficient mOhmcm K-1 T2 - Thermocouple Alloy 29-33 0.0019 Ni95/(Al+Mn+Si) 5 Tantalum/Tungsten 17.6 - Ta90/W 10 Tin/Lead/Antimony 14.8 - Sn60/Pb39/Sb 1 Tin/Silver 10.5 - Sn96/Ag 4 Tinned Copper 1 - 2 - CuSn Titanium/Aluminium/ 168 0.0004 Vanadium Ti90/Al 6/V 4 Titanium/Aluminium/ 126 - Vanadium Ti94.5/Al 3/V 2.5 Titanium/Molybdenum/ 135 - Niobium/Aluminium/Silicon Ti78.8/Mo15/Nb 3/Al 3/Si 0.2 Tungsten/Copper 3.7 - W 60/Cu40 Tungsten/Copper 4.1 - W 80/Cu20 Tungsten/Rhenium 29 - W 75/Re25 Tungsten/Rhenium 9.5 - W 95/Re 5 Tungsten/Rhenium 9.5 - W 97/Re 3 Waspaloy1 - Heat Resisting 120-130 - Alloy Ni58/Cr19/Co14/Mo/Ti/Al/Fe All information and technical data are given as a guide only.
Load more

Recommended publications
  • Structural, Thermal and Magnetic Analysis of Fe75co10nb6b9 and Fe65co20nb6b9 Nanostructured Alloys
    materials Article Structural, Thermal and Magnetic Analysis of Fe75Co10Nb6B9 and Fe65Co20Nb6B9 Nanostructured Alloys Albert Carrillo, Jason Daza, Joan Saurina, Lluisa Escoda and Joan-Josep Suñol * Department of Physics, Higher Polytechnic School, Campus Montilivi s/n, University of Girona, 17003 Girona, Spain; [email protected] (A.C.); [email protected] (J.D.); [email protected] (J.S.); [email protected] (L.E.) * Correspondence: [email protected] Abstract: Two nanocrystalline ferromagnetic alloys of the Fe-Co-Nb-B system have been produced by mechanical alloying (MA). Their microstructure, thermal behavior and magnetic response were checked by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and vibrating sample magnetometry (VSM). After 80 h of MA, the alloys were nanostructured (bcc-Fe(Co)-rich phase). As the Co content increases, the density of the dislocations decreases. Besides, a higher concentration of Co causes an increase in the activation energy of the crystallization process. The calculated energies, 267 and 332 kJ/mol, are associated to the crystalline growth of the bcc-Fe-rich phase. The Co content of the samples has no effect on the value of the saturation magnetization, whereas the coercivity is lower in the alloy containing less Co. Samples were compacted and heat-treated. Optimal annealing reduces the coercivity by a factor of two. Results were compared with the data of Fe-Nb-B and Fe-Ni-Nb-B alloys. Keywords: mechanical alloying; Fe-Co-Nb-B alloys; ferromagnetic alloys; thermal analysis; Citation: Carrillo, A.; Daza, J.; X-ray diffraction Saurina, J.; Escoda, L.; Suñol, J.-J.
    [Show full text]
  • INFLUENCE of PURITY and FABRICATION TECHNOLOGY on the PROPERTIES of SOFT MAGNETIC Fe- 50Ni ALLOY
    U.P.B. Sci. Bull., Series B, Vol. 69, No. 2, 2007 ISSN 1454-2331 INFLUENCE OF PURITY AND FABRICATION TECHNOLOGY ON THE PROPERTIES OF SOFT MAGNETIC Fe- 50Ni ALLOY Violeta TSAKIRIS1, Maria PETRESCU2 Aliajul Fe-50Ni apaţinând grupului de aliaje Permalloy cu aplicaţii în electronică, automatică, telefonie, instrumente electrice fine, a fost elaborat din fier extramoale şi nichel de înaltă puritate (99,95Ni). La elaborare s-a folosit topirea prin inducţie în aer sub protecţie cu insuflare de argon, în locul topirii în vid. Aliajul a fost forjat şi apoi recopt în atmosferă de H2 pentru a obţine o microstructură favorabilă şi o creştere a purităţii chimice şi fizice. Când aliajului forjat i s-a aplicat tratamentul termic de recoacere în H2, s-a obţinut o scădere a durităţii Brinell de la 182 la 130 daN/mm2 şi a câmpului coecitiv de la 0,5 la 0,4 Oe, împreună cu o creştere a permeabiltaţii magnetice de la 16000 la 23000 Gs/Oe şi a inducţiei la saturaţie de la 12300 la 14940 Gs. Luând în considerare creşterea grăunţilor produsă de tratamentul termic de recoacere se poate stabili un paralelism între scăderea de duritate prezisă de teoria dislocaţiilor şi modificarea proprietăţilor magnetice prezisă de teoria câmpului coercitiv. The soft magnetic alloy Fe-50Ni belonging to the Permalloy group that finds application in electronics, automatics, telephony and fine electrical devices has been obtained from extra-mild iron and high purity nickel (99.95). Induction melting was carried out in air under a protective argon blanket instead of vacuum melting. Forging and annealing in H2 atmosphere have been applied for obtaining a favourable microstructure and an increase in chemical and physical purity.
    [Show full text]
  • Process for Manufacturing Alnico System Permanent Magnet
    Europaisches Patentamt (19) European Patent Office Office europeenpeen des brevets EP 0 662 239 B1 (12) EUROPEAN PATENT SPECIFICATION (45) Date of publication and mention (51) intci.6: H01F 1/08, B22F 9/10, of the grant of the patent: C22C 38/16 03.12.1997 Bulletin 1997/49 (86) International application number: (21) Application number: 94922384.6 PCT/KR94/00100 Date of 27.07.1994 (22) filing: (87) International publication number: WO 95/04362 (09.02.1995 Gazette 1995/07) (54) PROCESS FOR MANUFACTURING ALNICO SYSTEM PERMANENT MAGNET VERFAHREN ZUR HERSTELLUNG EINES PERMANENTMAGNETEN AUF ALNICO-BASIS PROCEDE DE FABRICATION D'UN AIMANT PERMANENT EN ALNICO (84) Designated Contracting States: (56) References cited: DE GB • CHEMICAL ABSTRACTS, Vol. 102, No. 16, issued 1985, April 22 (Columbus, Ohio, USA), (30) Priority: 27.07.1993 KR 9314285 Hitachi Metals, "Alnico Permanent Magnet Alloy", page 275, column 1, Abstract No. (43) Date of publication of application: 1 36354a, Jpn. Kokai Tokkyo Koho; & JP, A,59 1 90 12.07.1995 Bulletin 1995/28 338. • CHEMICAL ABSTRACTS, Vol. 102, No. 16, (73) Proprietors: issued 1985, April 22 (Columbus, Ohio, USA), • POHANG IRON & STEEL CO., LTD. Hitachi Metals, "Alnico Permanent Magnet Pohang City, Kyong Sang Book-Do 790-300 (KR) Alloy", page 275, column 1, Abstract No. • RESEARCH INSTITUTE OF INDUSTRIAL 1 36355b, Jpn. Kokai Tokkyo Koho; & JP, A,59 1 90 SCIENCE & TECHNOLOGY 337. Pohang City, Kyong Sang Book-Do 790-330 (KR) • PATENT ABSTRACTS OF JAPAN, Unexamined Applications, Field C, Vol. 9, No. 247, issued (72) Inventors: 1985, October 03, The Patent Office Japanese YANG, Choong, Jin, Government, page 71; & JP,A,60 103 150 Res.
    [Show full text]
  • Leadership in Soft Magnetic Alloys Leadership in Soft Magnetic Alloys
    cartech.com Leadership in Soft Magnetic Alloys Leadership in Soft Magnetic Alloys CARPENTER TECHNOLOGY CORPORATION OFFERS A WIDE SELECTION OF SOFT MAGNETIC ALLOYS TO MEET YOUR MATERIALS SPECIFICATIONS. Choose from high permeability alloys, shielding alloys, silicon core irons or high- THE RESULT OF DECADES flux-density cobalt-iron alloys that have been used in applications ranging from simple magnetic cores to the most complex electronic circuitry. All are produced OF MATERIALS EXPERTISE to Carpenter’s exacting standards of consistency for uniform magnetic response IS CARPENTER’S ABILITY TO using premium-melting vacuum technologies. CONSISTENTLY HELP OUR Carpenter soft magnetic alloys have been used in the following applications: CUSTOMERS COMPETE IN A • Motor laminations • Relays • Magnetic amplifiers • Speedometers CHANGING WORLD. • Magnetic bearings • Transformers • Magnetic shielding • Vacuum equipment • Forged electromagnetic components • Watt-hour meters • GFCI World-Class Manufacturing and Quality Systems Carpenter is a fully integrated manufacturer, using advanced equipment and technologies including vacuum induction melting, vacuum arc remelting, double-vacuum melting (VIM-VAR), in-line hot rolling, and modern cold finishing equipment. This combination of capabilities, coupled with a highly skilled work force, supports your requirements for consistent, quality material lot after lot. Selecting Carpenter Soft Magnetic Alloys The matrix below compares various classes or “families” of soft magnetic alloys in terms of their relative
    [Show full text]
  • Hiperco 50 and Hiperco 50A Soft Magnetic Alloy Rod, Bar, Plate, Strip, Coil Hiperco 50 and Hiperco 50A Soft Magnetic Alloy Rod
    Hiperco 501 and Hiperco 50A1 Soft Magnetic Alloys 769 Susquehanna Avenue, Franklin Lakes, NJ 07417 • phone 201.891.4003 10537 Humbolt Street, Los Alamitos, CA 90720 • phone 562.431.2568 DESCRIPTION An alloy of 49% Cobalt, and 2% Vanadium, balance Iron, Hiperco 50 and Hiperco 50A have the highest magnetic saturation of all soft-magnetic alloys and excels in applications where this attribute is needed. Hiperco 50 maintains its strength after heat treating making it your best choice for applications that experience high forces (e.g. rotating parts). APPLICATIONS Special Motors for the Aerospace Industry (e.g. applications where high magnetic saturation and high strength is required with as little weight as possible); Electromagnets for medical appli- cations (e.g. to focus beams for radiation therapy in medical radiology applications); Electrical Generators; Specialty Transformers (e.g. electrical circuits and magnetic circuits where frequen- cies must be varied); Pole Pieces for Electromagnets; Magnetic Bearings (e.g. applications where rotating parts are levitated); High Magnetic Flux Devices and Instruments. TYPICAL DC MAGNETIC TYPICAL AC MAGNETIC PROPERTIES - 0.014" STRIP PROPERTIES - 0.014" STRIP Hiperco 50 Hiperco 50A Hiperco 50 Hiperco 50A Saturation Induction - Gausses 24,000 24,000 Core Loss W/lb @ 400Hz & 20k G 34 30 Maximum Permeability 12,000 15,000 B-40 Permeability @ 60Hz N/A N/A Coercive Force - Oersteds 0.9 0.4 N/A = not a typical application value Coercive Force - A/m 72 32 MECHANICAL PROPERTIES PHYSICAL PROPERTIES (Hiperco 50 & 50A) ANNEALED CONDITION Hiperco 50 Hiperco 50A Density lb/cu in 0.293 Tensile Strength ksi 118 104 Specific Gravity 8.12 MPa 814 717 Curie Temp ˚F 1720 Yield Strength ksi 63 53 ˚C 938 MPa 435 365 Melting Point ˚F 2600 Elongation % in 2 in.
    [Show full text]
  • Turbulent Heat Transfer and Pressure Drop
    DESIGN OPTIMIZATION OFMAGNETIC ALLOYS AND NICKEL-BASED SUPERALLOYS FOR HIGH TEMPERATURE APPLICATIONS Rajesh Jha George S. Dulikravich Department of Mechanical and Materials Engineering, MAIDROC Lab. Florida International University 10555 West Flagler Street, Miami, Florida 33174, U.S.A. [email protected], [email protected] Marcelo J. Colaço Department of Mechanical Engineering –POLI/COPPE Federal University of Rio de Janeiro - UFRJ Cidade Universitaria, Cx. Postal: 68503, Rio de Janeiro, RJ, 21941-972, Brazil [email protected] Abstract. Developing a new material or even improving properties of an existing material is a complex and time- consuming task. In recent years, materials scientists around the globe proposed a number of ways to speed up the alloy development process by using various computational tools. In this work, we made an attempt to demonstrate the efficacy of using computational tools in design optimization of materials, especially for high-temperature applications. We addressed two different material systems: Alnico alloys (magnetic) and Nickel-based superalloys. Alnico type alloys are hard magnetic alloys and well known for high-temperature applications. In this work, we defined the variable range of various elements and generated an initial set of alloys by a quasi-random sequence generation algorithm. These alloys were synthesized and tested for determining various material properties. We used a response surface methodology approach to develop surrogate models (meta-models) that approximately linked alloy chemistry with desired properties for these multi-component systems while being computationally affordable. These models were further used for multi-objective optimization of desired (conflicting) properties by using a number of algorithms based on evolutionary approaches, as well as our hybrid optimizer.
    [Show full text]
  • Additive Manufacturing and Topology Optimization of Magnetic Materials for Electrical Machines—A Review
    energies Review Additive Manufacturing and Topology Optimization of Magnetic Materials for Electrical Machines—A Review Thang Pham 1,*,† , Patrick Kwon 2,† and Shanelle Foster 1,*,† 1 Department of Electrical and Computer Engineering, Michigan State University, East Lansing, MI 48824, USA 2 Department of Mechanical Engineering, Michigan State University, East Lansing, MI 48824, USA; [email protected] * Correspondence: [email protected] (T.P.); [email protected] (S.F.); Tel.: +1-517-355-5234 (T.P.) † Current address: College of Engineering, Michigan State University, 428 S. Shaw Lane, East Lansing, MI 48824, USA. Abstract: Additive manufacturing has many advantages over traditional manufacturing methods and has been increasingly used in medical, aerospace, and automotive applications. The flexibility of additive manufacturing technologies to fabricate complex geometries from copper, polymer, and ferrous materials presents unique opportunities for new design concepts and improved machine power density without significantly increasing production and prototyping cost. Topology optimiza- tion investigates the optimal distribution of single or multiple materials within a defined design space, and can lead to unique geometries not realizable with conventional optimization techniques. As an enabling technology, additive manufacturing provides an opportunity for machine designers to overcome the current manufacturing limitation that inhibit adoption of topology optimization. Successful integration of additive manufacturing and topology optimization for fabricating magnetic components for electrical machines can enable new tools for electrical machine designers. This article presents a comprehensive review of the latest achievements in the application of additive manu- facturing, topology optimization, and their integration for electrical machines and their magnetic components. Citation: Pham, T.; Kwon, P.; Foster, S.
    [Show full text]
  • Solidification Process, Mechanical and Electrochemical Properties of Amorphous and Nanocrystalline Iron Alloy for a Power System Application
    Int. J. Electrochem. Sci., 16 (2021) Article ID: 210839, doi: 10.20964/2021.08.39 International Journal of ELECTROCHEMICAL SCIENCE www.electrochemsci.org Solidification Process, Mechanical and Electrochemical Properties of Amorphous and Nanocrystalline Iron Alloy for a Power System Application Xiaozhong Xu*, Jiangang Li, Jiajie Yu, Xiaoqin Jiang, Gan Shao Sategrid Ningbo Electric Power Supply Company, Ningbo 315000, China *E-mail: [email protected] Received: 26 March 2021/ Accepted: 15 May 2021 / Published: 30 June 2021 Nanocrystalline alloy is widely used in power systems because of its advantages of high magnetic conductivity, low loss, high strength and high resistivity. The amorphous method was used to prepare iron with the best amorphous thin strip processing parameters: the size of circular quartz tube was 0.8 mm; the distance between the nozzle and the surface of copper roller was 0.5 mm; the linear speed of copper roller surface was 41 m/s; the pressure difference between the inside and outside of quartz tube was 0.03 MPa; the spray angle was 0°. The solidification of the Fe based nanocrystalline alloy was studied by the solidification morphology, X-ray diffraction analysis, magnetic properties and mechanical properties. According to EIS studies, a 360K undercooling temperature leads to an increase in the penetration of electrolyte ions into electrode structures due to the formation of a high surface area and a high electron-transfer rate. The experimental results show that the undercooling of the alloy melt can be significantly improved by the amorphous method; the crystallization process of the prepared nanocrystalline alloy was controlled by the growth of the nanocrystalline; the prepared Fe based nanocrystalline alloy was more suitable for the common mode choke core, and can reflect different degrees of magnetic properties under the influence of different annealing temperatures; the prepared Fe based nanocrystalline alloy was better than the coarse-grained alloy.
    [Show full text]
  • Laser Additive Manufacturing of Fe-Based Magnetic Amorphous Alloys
    magnetochemistry Review Laser Additive Manufacturing of Fe-Based Magnetic Amorphous Alloys Merve G. Ozden * and Nicola A. Morley Department of Material Science and Engineering, University of Sheffield, Sheffield S1 3JD, UK; n.a.morley@sheffield.ac.uk * Correspondence: mgozden1@sheffield.ac.uk Abstract: Fe-based amorphous materials offer new opportunities for magnetic sensors, actuators, and magnetostrictive transducers due to their high saturation magnetostriction (ls = 20–40 ppm) and low coercive field compared with polycrystalline Fe-based alloys, which have high magne- tostriction but large coercive fields and Co-based amorphous alloys with small magnetostriction (ls = −3 to −5 ppm). Additive layer manufacturing (ALM) offers a new fabrication technique for more complex net-shaping designs. This paper reviews the two different ALM techniques that have been used to fabricate Fe-based amorphous magnetic materials, including the structural and magnetic properties. Selective laser melting (SLM)—a powder-bed fusion technique—and laser- engineered net shaping (LENS)—a directed energy deposition method—have both been utilised to fabricate amorphous alloys, owing to their high availability and low cost within the literature. Two different scanning strategies have been introduced by using the SLM technique. The first strategy is a double-scanning strategy, which gives rise to maximum relative density of 96% and corresponding magnetic saturation of 1.22 T. It also improved the glassy phase content by an order of magnitude of 47%, as well as improving magnetic properties (decreasing coercivity to 1591.5 A/m and increasing magnetic permeability to around 100 at 100 Hz). The second is a novel scanning strategy, which Citation: Ozden, M.G.; Morley, N.A.
    [Show full text]
  • Electrical and Magnetic Properties of Metals
    \ 396-4 V) PUBLICATION a NBS SPECIAL / / National Bureau of Standards U.S. DEPARTMENT OF COMMERCE NATIONAL BUREAU OF STANDARDS The National Bureau of Standards' was established by an act of Congress March 3, 1901. The Bureau's overall goal is to strengthen and advance the Nation's science and technology and facilitate their effective application for public benefit. To this end, the Bureau conducts research and provides: (I) a basis lor the Nation's physical measurement system, (2) scientific and technological services for industry and government, (3) a technical basis for equity in trade, and 14) technical services to promote public safety. The Bureau consists of the Institute for Basic Standards, the Institute for Materials Research, the Institute for Applied Technology, the Institute for Computer Sciences and Technology, and the Office for Information Programs. THE INSTITUTE FOR BASIC STANDARDS provides the central basis within the United States of a complete and consistent system of physical measurement: coordinates that system with measurement systems of other nations; and furnishes essential services leading to accurate and uniform physical measurements throughout the Nation's scientific community, industry, and commerce. The Institute consists of the Office of Measurement Services, the Office of Radiation Measurement and the following Center and divisions: Applied Mathematics — Electricity — Mechanics — Heat — Optical Physics — Center " for Radiation Research: Nuclear Sciences; Applied Radiation — Laboratory Astrophysics — Cryogenics - — Electromagnetics - — Time and Frequency '-'. THE INSTITUTE FOR MATERIALS RESEARCH conducts materials research leading to improved methods of measurement, standards, and data on the properties of well-characterized materials needed by industry, commerce, educational institutions, and Government; provides advisory and research services to other Government agencies; and develops, produces, and distributes standard reference materials.
    [Show full text]
  • Magnetic Properties Study of the Mn-Al System with Additions of B Or C and Mechanical Milling Techniques
    University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Mechanical & Materials Engineering, Engineering Mechanics Dissertations & Theses Department of 8-2012 Magnetic Properties Study of the Mn-Al System with Additions of B or C and Mechanical Milling Techniques Timothy E. Prost University of Nebraska-Lincoln, [email protected] Follow this and additional works at: https://digitalcommons.unl.edu/engmechdiss Part of the Mechanical Engineering Commons, Metallurgy Commons, and the Other Materials Science and Engineering Commons Prost, Timothy E., "Magnetic Properties Study of the Mn-Al System with Additions of B or C and Mechanical Milling Techniques" (2012). Engineering Mechanics Dissertations & Theses. 30. https://digitalcommons.unl.edu/engmechdiss/30 This Article is brought to you for free and open access by the Mechanical & Materials Engineering, Department of at DigitalCommons@University of Nebraska - Lincoln. It has been accepted for inclusion in Engineering Mechanics Dissertations & Theses by an authorized administrator of DigitalCommons@University of Nebraska - Lincoln. MAGNETIC PROPERTIES STUDY OF THE Mn-Al SYSTEM WITH ADDITIONS OF B OR C AND MECHANICAL MILLING TECHNIQUES By Timothy E. Prost A THESIS Presented to the Faculty of The Graduate College at the University of Nebraska In Partial Fulfillment of Requirements For the Degree of Master of Science Major: Engineering Mechanics Under the Supervision of Professor Jeffrey E. Shield Lincoln, Nebraska August, 2012 MAGNETIC PROPERTIES STUDY OF THE Mn-Al SYSTEM WITH ADDITIONS OF B OR C AND MECHANICAL MILLING TECHNIQUES Timothy E. Prost, M.S. University of Nebraska, 2012 Adviser: Jeffrey E. Shield Recently a shift in the focus of permanent magnetic research has moved from Rare Earth (RE)-based alloys to those made from more readily available elements.
    [Show full text]
  • Strong Magnetic Shielding by Common Available Material
    Advanc of em al e rn n u ts o i J n l T a e n c o h International Journal of Advancements i t n a o n l r o Akash, Int J Adv Technol 2016, 7:4 e g t y n I in Technology DOI: 10.4172/0976-4860.1000168 ISSN: 0976-4860 Short Communication Open Access Strong Magnetic Shielding by Common Available Material Akash Yadav* Department of Mechanical Engineering, The ICFAI University Dehradun, India *Corresponding author: Akash Yadav, Department of Mechanical Engineering, The ICFAI University Dehradun, India; Tel: +919997655162; E-mail: [email protected] Received date: June 12, 2016; Accepted date: June 16, 2016; Published date: July 12, 2016 Copyright: © 2016 Yadav A. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited. Abstract Purpose of this research paper is to find way to shield a very strong magnet that is of neodymium n50 grades or any other grade. There are several places where we require to shield the magnets completely or some sides/part of it. There are materials available in market for shielding but they are costly. The main aspect of this paper is to find a material by which we can shield very strong magnetic field and the cost can be reduced by significant amount. The method is to use many different common available material to shield it which are available commonly. The material that are being used are ferromagnetic, paramagnetic and diamagnetic.
    [Show full text]