Pontiac 1996-Up Grand Am

TUNERS / CASSETTE / DISC PLAYERS RADIO UPDATED EQ PONTIAC SINGLE THROUGH MINI STAN DIN ISO DIN DBL DIN STACK '97 CHASSIS H 13/ -2 2 2 2 37/ 3 '98 4 8 1996-UP GRAND AM CHASSIS W 71/ 71/ 71/ 7 71/ 71/ '99 8 8 8 8 8 '2000 CHASSIS D 43/ -51/ 57/ -611/ 57/ -611/ 57/ -611/ 57/ -611/ 57/ -611/ Coupe and Sedan 4 2 8 16 8 16 8 16 8 16 8 16

5 3 5 3 3 13 3 NOSE H 1 /8-1 /4 1 /8-1 /4 2 /8 1 /16 3 /4-4

1 3 1 3 1 11 11 1 NOSE W 4 /8-4 /16 4 /8-4 /16 7 /2 6 /16 6 /16-7 /4

1 3 1 SHAFT SP. 5 /8-5 /4 5 /8-6 IN DASH APPLICATION NOTES

KS KS KS KS N KS

APPLICATION KIT MODEL: GM1500 SERIES

HARNESS ADAPTOR: GM02 ANTENNA ADAPTOR: MDA-1

IN-DASH INSTALLATION AREA DIMENSIONS MAX DEPTH DEPTH WIDTH HEIGHT

13 1 3 7 CAVITY 5 /16" 7 /2" 8 /16" 3 /8"

DASH 11/ 5 OPENING TYPE: M2000 7 16" 3 /16"

3 DASH MATERIAL: PLASTIC THICKNESS: /32" FOR MAX DEPTH X REMOVE REAR SUPPORT MODIFY CAVITY

AMPLIFIER/EQ MOUNTING LOCATIONS (WxHxD) UNDER/IN UNDER GLOVE TRUNK/ DASH SEAT BOX CARGO

Various

Dimensions shown are inches. For inch/mm conversions refer to chart section. . R U C C E C O

E N Y T E A U R M L

E O T F A S E H B R

T A

. A

S H S E I C A

C R L N A A E E U T S N S E I A R S

N D S O E I T C H N T N

E E R M S O U U

F . C

D E O E L D

E B I Y T L S N L N A U O R F P A E S U R E G A

C T

E O N B

N O

T T D O U E N B S N A D A B E

T . S I P C L M N I A

E , U T E T N H A A

C S M I S

S O Y I C C H S T A 5 . R

: B = BACK UP PLATES REQUIRED. K = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE E U E 1 D

I C = CUT TRIM/PLASTIC (STRUCTURE). KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER. T C U O C C2 = CUT STEEL. KS = SCOSCHE KIT RECOMMENDED. N A G D = BELOW DECK ONLY. N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED. D1 = LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT). P = PERFECT WITHOUT MODIFICATION. D2 = CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK. P1 = MODIFY OR REMOVE POCKETS. D3 = NARROW SURFACE, BELOW DECK ONLY. P2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT). F1 = MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING. P3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT. F2 = MODIFY DASH CAVITY AND/OR PANEL. R = REAR LOAD ISOMOUNT. K = INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED. U = UNDERDASH. K1 = KIT MODIFICATIONS REQUIRED. W1 = WITH POWER WINDOWS ONLY. K2 = EXTENSION KIT RECOMMENDED. W2 = WITHOUT POWER WINDOWS ONLY. K3 = WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO. K4 = FABRICATE PANEL/BRACKETS.

DASH WITH GM1503 KIT INSTALLED. FRONT DOOR PANEL.

PRELIMINARY: DISCONNECT THE NEGATIVE BATTERY CABLE

ANTENNA: THE FACTORY ANTENNA IS LOCATED ON THE RIGHT REAR FENDER. RADIO REMOVAL AND IN-DASH INSTALLATION: NOTE: THE FACTORY RADIO PROVISION IS FOR A M2000 CHASSIS RADIO. AN INSTALLATION KIT IS REQUIRED FOR ALL AFTERMARKET INSTAL- LATIONS. WE RECOMMEND THE USE OF A SCOSCHE GM1500 SERIES KIT. NOTE: THE FACTORY BRACKETS DO NOT REMOVE AND THE USE OF SCOSCHE OE BRACKET SETS OR UNIVERSAL BRACKETS IS RE- QUIRED. 1. EXTRACT (2) SCREWS FROM DASH BEZEL ABOVE INSTRUMENT/ GAUGES. 2. EXTRACT (2) SCREWS FROM BACK OF DEEP STORAGE POCKET BELOW THE RADIO. 3. CAREFULLY PULL OUT ON THE INSTRUMENT/RADIO PANEL TO RELEASE SNAP CLIPS, UNPLUG SWITCHES AND REMOVE BEZEL. 4. EXTRACT (3) 7 MM SCREWS SECURING RADIO, UNPLUG CONNECTORS, ANTENNA LEAD, AND REMOVE RADIO. FRONT DOOR SPEAKER INSTALLATION: NOTE: THE FACTORY RADIO PROVISION IS FOR A 4 x 6” SPEAKER ON A FRONT DOOR 4 x 6” SPEAKER AND TWEETER PROVISION. FACTORY ADAPTER PLATE. THERE IS AN ADDITIONAL 2" TWEETER MOUNTING PROVISION FOR AN UPGRADE TO THE FACTORY SYSTEM. 1. EXTRACT (2) SCREWS FROM THE DOOR PANEL ARMREST CUP. 2. LIFT UP ON CUP/POWER SWITCH PANEL FROM THE BACK EDGE FIRST, UNPLUG AND REMOVE. 3. CAREFULLY POP OUT THE DOOR RELEASE HANDLE PLASTIC CUP. 4. USE A PANEL REMOVAL TOOL TO POP OUT INSIDE MIRROR PLASTIC TRIANGLE. 5. REMOVE DOOR REFLECTOR AND EXTRACT (1) SCREW FROM BEHIND. 6. USE A PANEL REMOVAL TOOL TO POP OUT THE PANEL FASTENERS FROM AROUND SIDES AND BOTTOM OF DOOR PANEL. 7. EXTRACT (4) SCREWS HOLDING SPEAKER IN UNPLUG AND REMOVE. 8. IF NEEDED, EXTRACT (4) SCREWS HOLDING ADAPTER PLATE AND REMOVE. REAR DECK SPEAKER INSTALLATION: NOTE: THE FACTORY PROVISIONS ARE FOR A 6 x 9” SPEAKERS. 1. EXTRACT (2) 13 MM BOLTS FROM FRONT EDGE OF BOTTOM REAR SEAT CUSHION, LIFT AWAY AND REMOVE. 2. EXTRACT (2) BOLTS FROM BELOW REAR SEAT UPRIGHT CUSHION LIFT CUSHION UP TO REMOVE. 3. EXTRACT (2) SCREWS FROM EACH SIDE DOOR SILL PANEL ALONG WHEEL WELL. 4. USE A PANEL REMOVAL TOOL TO POP OUT FASTENERS FROM REAR SIDE PILLAR PANELS AND REMOVE. REAR DECK 6 x 9” SPEAKER PROVISION. 5. LIFT REAR DECK UP AND AWAY TO REMOVE. 6. EXTRACT (4) SCREWS HOLDING SPEAKER IN, UNPLUG AND REMOVE SPEAKER.