DUR-900

A N O R D I C B R A N D

ENG User Guide LAV Lietotāja rokasgrāmata

SWE Användarhandledning EST Kasutusjuhend

FIN Käyttöohje GER Bedienungsanleitung

DAN Brugervejledning FRA Mode d’emploi

NOR Brukerveiledning POL Instrukcja użytkowania

LIT Naudotojo vadovas NLD Gebruiksaanwijzing ENG - User Manual

Safety instructions 1. Do not look into or observe the device’s light, neither directly or through an optical instrument. 2. Do not disassemble or remove the lens cover. If the lens cover is removed, your eyes will be directly exposed to the light.

4. Keep the product away from children. . Do not continue to use the product if it has been damaged or deformed. Do not leave it in hot environments.

Product information This scanner provides an accurate, fast and easy complete solution for data entry and storage for computer information systems. The product has two working modes: manual and auto-sensor. This product provides 4 interfaces to connect to any host computer system: Keyboard (Keyboard wedge), RS-232, USB HID and VCOM. the device has been powered off. This product has more settings than available in this manual. If needed you can create your own barcodes to set your own settings. One example is the “LED on time”, it has about 200 possible settings but only 4 examples of barcodes are in this for the corresponding setting you want to create or change.

Scan barcodes In order to obtain a good scan effect, you should aim the at the center of the barcode, but you can aim from any direction.

The closer the scanner is to the barcode, the smaller the aiming beam is; the farther away the scanner is from the barcode, the larger the aiming beam is. If the barcode is small, the scanner should be close to the barcode; if the barcode is large, the scanner should be farther away from the barcode, so the barcode can be read easily and correctly.

3 1. Scan window

1 2. Button

4 3. LED 2 4. Sound output

5. Cable removal hole 5 Cable removal 1. Locate the cable removal hole on the bottom of the scanner.

Readability VS performance Each type of barcode has its own unique properties. Enable the ability to read barcode types via the settings found in this manual. You can disable the scanner from reading barcode types that will not be used to improve the scanner’s performance.

Maintenance 1. Stains and dust on the scan window may affect the scanning. Use a lint-free cloth / lens tissue of good quality to gently wipe clean the window if needed. Poor quality paper will damage the surface smoothness of the scan window and affect the scanner’s effect. 2. The scanner’s housing can be wiped with a clean soft cloth. When needed, moisten the cloth with water or a mild soap solution and wipe it with a soft cloth.

1 Troubleshooting Q1. Problem: The data cable is correctly installed, but the indicator LED or beep sound is not working when the button is pressed. A1. Possible causes: No power or cable error. Solutions: Please make sure the cable is connected and the scanner is turned on. When using the USB port, please connect the USB cable to the USB port of the computer motherboard. Do not use an extended USB port or other USB extension cable. Check if the cable connection is loose. Q2. Problem: The light is on but barcode cannot be read. A2. Possible causes: The barcode type is not enabled, damaged barcode or inappropriate scan distance. Solutions: Enable the barcode type. Try scanning other barcodes with the same barcode type. Move the barcode scanner closer or farther away from the barcode. Q3. Problem: The scanned data is displayed incorrectly on the host after the A3. Possible causes: Input error or other settings for the scanner. Solutions: Change input to default English input or restore the scanner to factory default. Q4. Problem: Other situations. A4. Possible cause: Scanner operation error. Solutions: Turn off and reconnect the device and scanner correctly. Turn on the power of the device, restore the scanner to the factory default and rescan the barcode.

Support More product information can be found at www.deltaco.eu. Contact us by e-mail: [email protected].

2 SWE - Manual

Säkerhetsinstruktioner 1. Titta inte in i enhetens ljusstråle, varken direkt eller genom något optiskt instrument. 2. Ta inte bort eller demontera linsskyddet. Om linsskyddet tas bort kommer dina ögon att exponeras direkt för ljuset.

4. Håll produkten borta från barn. 5. Utsätt inte produkten för stötskador eller tryck och utsätt inte produkten för eld eller sänk ner den i vatten. Fortsätt inte att använda produkten om den har skadats eller deformeras. Lämna den inte i heta miljöer.

Produktinformation Denna streckkodsläsare ger en exakt, snabb och enkel komplett lösning för datainmatning och lagring för datorinformations- system. Produkten har två arbetslägen: manuell och autosensor. Denna produkt har 4 gränssnitt för att ansluta till värddatorsystem: Tangentbord (Keyboard wedge), RS-232, USB HID och VCOM. om enheten har blivit avstängd. egna streckkoder för att ställa in egna inställningar. Ett exempel är “LED on time”, den har cirka 200 möjliga inställningar för den motsvarande inställning du vill skapa eller ändra.

Skanna streckkoder För att få en bra skanningseffekt bör du rikta streckkodsläsaren på mitten av streckkoden. Sträva efter att skanna streckkoderna rakt framifrån.

Ju närmare skannern är streckkoden, desto mindre är strålen. Ju längre bort skannern är från streckkoden, desto större är strålen. Om streckkoden är liten ska skannern vara nära streckkoden; Om streckkoden är stor så ska skannern vara längre bort från streckkoden, så streckkoden kan läsas av enkelt och korrekt.

3 1. Skanningsfönster

1 2. Knapp 4 3. LED 2 4. Ljudutgång

5. Borttagningshål för kabeln 5 Lossa kabeln 1. Lokalisera borttagningshålet för kabeln längst ner på skannern. 2. Sätt i en nål eller ett gem i hålet och tryck hårt medan du försiktigt drar ut kabeln.

Rätt inställning ökar prestanda Varje typ av streckkod har sina egna unika egenskaper. Aktivera möjligheten att läsa streckkodstyper via de inställningar som inte kommer att användas för att förbättra skannerns prestanda.

Underhåll 1. Fläckar och damm i skanningsfönstret kan påverka skanningen. Använd en luddfri torkduk/linsservett av god kvalitet för att försiktigt torka ren fönstret vid behov. Papper av dålig kvalitet kommer att skada ytans jämnhet i skanningsfönstret och påverka skannerns effekt. 2. Skannerns hölje kan torkas med en ren mjuk trasa. Vid behov, fukta trasan med vatten eller en mild tvållösning och torka med en mjuk trasa.

3 Felsökning Q1. Problem: Datakabeln är korrekt installerad, men indikatorlampan eller pipljudet fungerar inte när knappen trycks in. A1. Möjliga orsaker: Ingen ström- eller kabelfel. Lösningar: Se till att kabeln är ansluten och att scannern är påslagen. Anslut USB-kabeln till USB-porten på datorns moderkort när du använder USB-porten. Använd inte en förlängd USB-port eller annan USB-förlängningskabel. Kontrollera om kabelanslutningen är lös. Q2. Problem: Lampan är på men streckkoden kan inte läsas av. A2. Möjliga orsaker: Streckkodstypen är inte aktiverad, skadad streckkod eller olämpligt skanningsavstånd. Lösningar: Aktivera streckkodstypen. Prova att skanna andra streckkoder med samma streckkodstyp. Flytta streckkods- läsaren närmare eller längre bort från streckkoden. Q3. Problem: Den skannade datan visas upp felaktigt på värddatorn när skannern blinkar rött. A3. Möjliga orsaker: Inmatningsfel eller andra inställningar för skannern. Lösningar: Ändra inmatning till standard engelska inmatning eller återställ skannern till fabriksinställningen. Q4. Problem: Övriga situationer. A4. Möjlig orsak: Fel på skannerfunktionen. Lösningar: Stäng av och återanslut enhet och skanner på rätt sätt. Slå på strömmen på enheten, återställ skannern till fabriksinställningen och skanna streckkoden igen.

Support www.deltaco.eu. Kontakta oss via e-post: [email protected].

4 FIN - Manual

Turvallisuusohjeet 1. Älä katso suoraan kohti lukuvaloa. Älä myöskään tarkkaille sitä optisella instrumentilla. 2. Älä irrota linssin suojusta. Jos suojus ei ole paikallaan, silmät altistuvat suoraan lukuvalolle. 3. Ainoastaan valtuutettu sähköasentaja saa avata laitteen, tehdä siihen muutoksia tai korjata sen. 4. Pidä laite poissa lasten ulottuvilta. 5. Suojaa laite kolhuilta ja siihen kohdistuvalta paineelta. Älä altista laitetta tulelle tai vedelle. Lopeta laitteen käyttö, jos se on vahingoittunut tai siinä on vaurioitumisen merkkejä. Älä säilytä laitetta kuumissa tiloissa.

Toimintaperiaate Viivakoodinlukija on nopea ja helppokäyttöinen tiedontallennusratkaisu. Laitteessa on kaksi eri toimintatilaa: manuaalinen ja automaattinen tunnistus. Siinä on neljä liitäntätyyppiä, joilla sen voi kytkeä tietokoneeseen: näppäimistöliitäntä (Keyboard wedge), RS-232, USB HID ja VCOM. Laite tekee tarvittavat asetukset, kun sillä alkaa lukea viivakoodeja. Asetukset tallentuvat EEPROM-muistiin, jossa ne pysyvät myös laitteen ollessa suljettuna. Käyttöohjeessa kuvataan vain osa laitteen asetuksista. Jos haluaa käyttää omia viivakoodityyppejä, niitä varten on mahdol- lista luoda omia asetuksia. Yhtenä esimerkkinä on ”LED on time”, josta on olemassa noin 200 eri asetusta. Tässä tekstissä

reader”, jossa kerrotaan viivakoodityyppien luomisesta ja muokkaamisesta.

Viivakoodien lukeminen Saavutat paremman lukunopeuden, kun kohdistat laitteen viivakoodin keskikohtaan. Laite toimii kuitenkin myös muihin kohtiin osoitettuna.

Lukusäde pienenee, kun laite asetetaan lähemmäs viivakoodia. Kun sen siirtää kauemmas, säde vastaavasti suurenee. Viivakoodinlukija tulee asettaa lähelle kohdetta, jos viivakoodi on pienikokoinen. Suurten viivakoodien kohdalla laite kannattaa asettaa hieman kauemmas kohteesta. Jos viivakoodi on valmistettu heijastavasta materiaalista, sen lukeminen saattaa vaatia laitteen kallistamista. 3 1. Lukuikkuna

1 2. Painike

4 3. LED-valo 2 4. Ääniulostulo

5. Kaapelin irrotuskytkin 5 Kaapelin irrottaminen 1. Etsi kaapelin irrotuskytkin, joka on laitteen alaosassa. 2. Paina paperiliitintä koloon. Kun se on painettuna sisään, vedä kaapeli varovaisesti ulos.

Suorituskyvyn parantaminen Kullakin viivakoodityypillä on omat tekniset erityispiirteensä. Näissä ohjeissa kuvataan, miten yksittäisiä tyyppejä saa aktivoitua. Laitteen suorituskyky paranee, kun kytkee käyttämättömät viivakoodityypit pois päältä.

Puhdistaminen 1. Laite toimii hitaammin, jos lukuikkunassa on pölyä tai tahroja. Pyyhi ikkuna huolellisesti pehmeällä liinalla ja puhalla sitä hiustenkuivaajalla. Jos pyyhkimiseen käyttää karkeaa paperia, ikkunan pinta tulee epätasaiseksi ja lukunopeus saattaa pienentyä. 2. Laitteen ulkokuoren voi pyyhkiä pehmeällä liinalla. Lisää tarvittaessa vettä ja pieni määrä puhdistusainetta ja pyyhi lopuksi toisella liinalla.

5 Vianmääritys Q1. Ongelma: Datakaapeli on kytketty oikein, mutta laite ei sytytä merkkivaloa tai toista merkkiääntä painikkeen painalluksen yhteydessä. A1. Mahdolliset syyt: Ei virtaa tai viallinen kaapeli. Ratkaisut: Varmista, että kaapeli on kytketty oikein ja että laite on kytketty päälle. Jos käytät USB-kaapelia, kytke se suoraan tietokoneeseen. Tarkista, että kaapeli on kunnolla kiinni. Q2. Ongelma: Merkkivalo syttyy, mutta viivakoodin lukeminen ei onnistu. A2. Mahdolliset syyt: Viivakoodityyppiä ei ole aktivoitu, viivakoodi on vahingoittunut tai lukuetäisyys on virheellinen. Ratkaisut: Aktivoi viivakoodityyppi. Kokeile lukea muita viivakoodeja, jotka ovat samantyyppisiä. Siirrä laitetta lähemmäs tai kauemmas kohteesta. Q3. Ongelma: Tietokoneelle ilmestyy virheellistä tietoa. A3. Mahdolliset syyt: Lukuvirhe tai virheelliset asetukset viivakoodinlukijassa. Ratkaisut: Valitse syöttökieleksi englanti tai palauta laitteen tehdasasetukset. Q4. Ongelma: Virhetilanne, jota ei ole kuvattu yllä olevissa kohdissa. A4. Mahdolliset syyt: Lukutoimintoon liittyvä virhe. Ratkaisut: Sammuta sekä tietokone että viivakoodinlukija. Irrota niiden välillä oleva kaapeli ja kytke se uudestaan paikalleen. Kytke tietokoneen virta päälle, palauta viivakoodinlukijan tehdasase- tukset ja kokeile lukea viivakoodi uudestaan.

Asetuksien tekeminen Tämä käyttöohjeiden kohta on saatavilla ainoastaan englanniksi.

Tuotetuki Tuotteesta on lisätietoja osoitteessa www.deltaco.eu. Tukipalvelun sähköpostiosoite on

6 DAN - Brugermanual

Sikkerhedsinstruktioner 1. Kig ikke direkte på og observer ikke enhedens lys ved hjælp af et optisk instrument 2. Du må ikke afmontere eller fjerne linsedækslet. Hvis linsedækslet er fjernet, vil dine øjne blive direkte udsat for lyset.

4. Hold produktet utilgængeligt fra børn. 5. Udsæt ikke produktet chokskader, tryk og sæt ikke produktet i brand og nedsænk det ikke i vand. Brug ikke produktet, hvis det er beskadiget eller deformt. Lad det ikke stå i varme omgivelser.

Produkt information Denne stregkodescanner giver en præcis, hurtig og nem komplet løsning til dataindtastning og lager for computerinformations- systemer. Produktet har to arbejdstilstande: Manuel og automatisk sensor. Tastatur (Tastatur kile), RS-232, USB HID og VCOM. selvom enheden er slukket. Dette produkt stregkoder for at indstille dine egne indstillinger. Fx ‘LED on time’. Denne har omkring 200 mulige indstillinger, men der indstilling som du vil oprette eller ændre.

Scan stregkoder For at opnå god scanningseffekt, bør du rette stregkodelæseren mod midten af stregkoden, men du kan sigte fra hvilken som helst retning.

Jo tættere scanneren er på stregkoden, desto mindre er sigtestrålen. Jo længere væk scanneren er fra stregkoden, desto større er sigtestrålen. Hvis stregkoden er lille, skal scanneren være tæt på stregkoden; Hvis stregkoden er stor, skal scanneren længere væk fra stregkoden, så stregkoden kan læses nemt og korrekt.

3 1. Scannings vindue

1 2. Knap

4 3. LED 2 4. Lydudgang

5. Kabelfjernelseshul. 5

Fjernelse af kabel 1. Find kabelfjernelseshullet i bunden af scanneren. 2. Sæt en papirklips i hullet, og tryk let på klipsen, men du trækker kablet forsigtigt ud. Læsbarhed vs. ydeevne Hver type stregkode har sine egne unikke egenskaber. Aktiver evnen til at læse stregkodetyper via indstillingerne fundet i denne manual. Du kan deaktivere scanneren fra at læse stregkodetyper, som ikke vil blive brugt, for at forbedre scanneres ydeevne. Vedligeholdelse 1. Pletter og støv på scanner vinduet kan påvirke scanneren. Brug en fnugfri klud / linseklud af god kvalitet til forsigtigt at påvirke scannerens effekt. 2. Scannerens hus kan tørres af med en ren, blød klud. Hvis det er nødvendigt, fugtes kluden med vand eller mild sæbe- opløsning og tørres derefter af med en blød klud.

7

Q1. Problem: Datakablet er korrekt installeret, men indikatorlampen eller biplyden virker ikke når der trykkes på knappen. A1. Mulige årsager: Ingen strøm eller kabelfejl. Løsninger: Sørg for at kablet er tilsluttet og scanneren er tændt. Når du bruger USB-porten, skal du tilslutte USB-kablet til USB-porten på computerens bundkort. Brug ikke en udvidet USB-port eller andet USB-forlængerkabel. Kontrollér om ledningsforbindelsen er løs. Q2. Problem: Lyset er tændt, men stregkoden kan ikke læses. A2. Mulige årsager: Stregkodetypen er ikke aktiveret, beskadiget stregkode eller upassende scanningsafstand. Løsninger: Aktiver stregkodetype. Prøv at scanne andre stregkoder med samme stregkodetype. Flyt stregkodescanneren tættere på eller længere væk fra stregkoden. Q3. Problem: De scannede data vises forkert på værten, efter at scanneren blinker rødt. A3. Mulige årsager: inputfejl eller andre indstillinger for scanneren. Løsninger: Skift input til default engelsk eller gendan scanneren til fabriksindstillinger. Q4. Problem: Andre situationer. A4. Mulige årsager: Scanner drift fejl. Løsninger: Sluk for og tilslut igen enheden og scanneren korrekt. Tænd for enhedens strøm, genindstil scanner til fabriksindstillinger og genscan stregkoden.

Support www.deltaco.eu. Kontakt os via e-mail: [email protected].

8 NOR - Brukermanual

Sikkerhetsinstruksjoner 1. Ikke se direkte inn i, eller observer lyset fra enheten ved å bruke optiske instrumenter. 2. Ikke demonter eller fjern linsedekselet. Om linsedekselet fjernes vil øynene dine bli direkte eksponert for lyset.

4. Hold produktet unna barn. skadet. Ikke forlat eller oppbevar produktet i varme områder.

Brukerstøtte www.deltaco.eu. E-Post: [email protected]

9 LIT - Naudotojo vadovas

Saugos instrukcijos 1. Tiesiogiai nežiūrėkite į arba nestebėkite prietaiso skleidžiamos šviesos optiniu instrumentu. 2. Neišardykite ar nenuimkite objektyvo dangtelio. Jeigu objektyvo dangtelis nuimtas, Jūsų akis tiesiogiai veiks prietaiso skleidžiama šviesa.

4. Gaminį laikykite vaikams neprieinamoje vietoje. 5. Netrankykite, nespauskite, nepadekite arba nepanardinkite gaminio į vandenį. Nenaudokite pažeisto arba deformuoto gaminio. Gaminio nepalikite karštoje aplinkoje.

Informacija apie gaminį Šis brūkšninių kodų skaitytuvas kompiuterių informacijos sistemoms suteikia tikslų, greitą ir lengvą duomenų įrašymo bei saugojimo sprendimo būdą. Gaminyje yra du darbo režimai: rankinis ir automatinio jutiklio režimas. Šiame gaminyje yra keturios sąsajos prisijungimui prie bet kokios kompiuterio sistemos: klaviatūra (klaviatūros jungtis), RS-232, USB HID ir VCOM. atmintyje; nustatymai lieka išsaugoti net tada, kai prietaisas yra išjungtas. Šis gaminys turi daugiau nustatymų nei šiame naudotojo vadove nurodyti brūkšniniai kodai. Esant poreikiui, galite susikurti savo brūkšninius kodus ir nustatyti savus nustatymus. Vienas pavyzdys yra „LED on time“ (liet. „LED laiku“); šioje programoje yra apytiksliai 200 galimų nustatymų, bet šiame naudotojo vadove pateikiami tik keturi brūkšninių kodų norimą sukurti arba pakeisti atitinkamą nustatymą.

Brūkšninių kodų nuskaitymas Norint geriausiai nuskaityti, brūkšninių kodų skaitytuvą reikia nukreipti į brūkšninio kodo centrą, tačiau jį galite nukreipti iš bet kurios pusės.

Kuo arčiau brūkšninio kodo yra skaitytuvas, tuo mažesnis yra nusitaikymo spindulys; kuo toliau brūkšninio kodo yra skaitytuvas, tuo didesnis yra nusitaikymo spindulys. Jeigu brūkšninis kodas yra mažo dydžio, skaitytuvas turi būti arti jo; jeigu brūkšninis kodas yra didelio dydžio, skaitytuvas turi būti toliau nuo jo tam, kad brūkšninį kodą būtų galima lengvai ir teisingai nuskaityti. Jeigu brūkšninis kodas labai atspindi šviesą (pvz., padengtas medžiaga), jo nuskaitymui gali reikėti pakreipti skaitytuvą. 3 1. Nuskaitymo langelis

1 2. Mygtukas

4 3. LED 2 4. Garso išvestis

5. Laido ištraukimo anga 5

Laido ištraukimas 1. Skaitytuvo apačioje suraskite laido ištraukimo angą. 2. Į ją įstatykite sąvaržėlę. Stipriai ją spauskite ir švelniai traukite laidą.

Nuskaitymas ir našumas Kiekvienas brūkšninis kodas turi savo unikalias savybes. Įgalinkite skirtingų brūkšninių kodų nuskaitymą naudodami šiame naudotojo vadove esančius nustatymus. Galite išjungti skaitytuvo galimybę nuskaityti nenaudojamus brūkšninius kodus jo našumui pagerinti

10 Priežiūra 1. Nuskaitymui gali daryti įtaką ant nuskaitymo langelio esančios dėmės arba dulkės. Langelį švelniai valykite geros kokybės nemedvilnine šluoste / lęšių valymo servetėle. Blogos kokybės popierius subraižys nuskaitymo langelio paviršių ir darys įtaką skaitytuvo rezultatams. 2. Skaitytuvo korpusą galima nuvalyti švaria minkšta šluoste. Esant reikalui, sudrėkinkite ją vandeniu arba nedidelio šarmingumo muilo tirpalu bei korpusą nuvalykite minkšta šluoste.

Trikčių šalinimas Q1. Gedimas: duomenų kabelis tinkamai įstatytas, bet nuspaudus mygtuką LED indikatorius neveikia arba nesigirdi pypsėjimo. A1. Galimos priežastys: nėra elektros arba kabelio gedimas. Sprendimo būdai: įsitikinkite, ar kabelis prijungtas ir įjungtas skaitytuvas. Naudodami USB prievadą, prijunkite USB laidą prie kompiuterio motininės plokštės USB prievado. Nenau- dokite USB prievado ilgintuvo arba kitokio USB laido ilgintuvo. Patikrinkite, ar kabelio jungtys neatsilaisvino. Q2. Gedimas: šviesa dega, bet negalima nuskaityti brūkšninio kodo. A2. Galimos priežastys: neįjungtas brūkšninio kodo nuskaitymo tipas, pažeistas brūkšninis kodas arba netinkamas atstumas. Sprendimo būdai: įjunkite brūkšninio kodo tipą. Pabandykite nuskaityti kitus tokio paties tipo brūkšninius kodus. Nuskaitydami brūkšninį kodą, priartinkite arba atitolinkite skaitytuvą. Q3. Gedimas: kai skaitytuve dega raudona spalva, nuskaityti duomenys rodomi klaidingai. A3. Galimos priežastys: įvesties klaida arba klaidingi skaitytuvo nustatymai. Sprendimo būdai: pakeiskite įvesties kalbą į anglų kalbą pagal nustatytuosius parametrus arba atstatykite gamyklinius nustatymus. Q4. Gedimas: kitos situacijos. Q4. Galimos priežastys: skaitytuvo veikimo klaida. Sprendimo būdai: išjunkite ir teisingai dar kartą prijunkite prietaisą ir skaitytuvą. Įjunkite prietaiso elektros tiekimą, atstatykite gamyklinius skaitytuvo nustatymus ir dar kartą nuskaitykite brūkšninį kodą.

Pagalba Išsamesnę informaciją apie gaminį rasite svetainėje: www.deltaco.eu. Susisiekite el. paštu: [email protected].

11 LAV - Lietotāja rokasgrāmata Drošības instrukcijas 1. Nelūkojieties tieši uz ierīces radīto gaismu un nenovērojiet to, izmantojot optisko instrumentu. 2. Neizjauciet un nenoņemiet objektīva vāciņu. Ja objektīva vāciņš ir noņemts, acis būs tieši pakļautas gaismas iedarbībai.

4. Neļaujiet bērniem piekļūt precei. 5. Nepakļaujiet preci triecieniem, spiedienam, kas var radīt tai bojājumus; nelieciet ierīci ugunī un neiegremdējiet to ūdenī. Neturpiniet izmantot preci, ja tā ir bojāta vai deformēta. Neatstājiet ierīci karstumā.

Informācija par preci Šis svītrkoda lasītājs nodrošina precīzu, ātru un vieglu pilnīgu risinājumu datu ievadei un uzglabāšanai datorsistēmās. Precei ir divi darbības režīmi: manuāls un automātiskais sensors. Produktam ir 4 saskarnes savienojumiem ar jebkuru saimniekdatora sistēmu: Tastatūra (Keyboard wedge), RS-232, USB HID un VCOM. zglabāti EEPROM tipa atmiņā, kas tiek saglabāta pat, ja ierīce ir izslēgta. Šajā precē iestatījumu ir vairāk nekā pieejamo svītrkodu. Ja nepieciešams, savos iestatījumos var izveidot savus svītrkodus. Piemēram, “LED on time” (LED darbošanās laiks) ir aptuveni 200 iespējami iestatījumi, bet šajā rokasgrāmatā sniegti tikai 4 svītrkodu piemēri. Attiecīgajam iestatījumam, kuru vēlaties izveidot vai mainīt, skatīt sadaļu angļu valodā

Svītrkodu skenēšana Lai panāktu labu skenēšanas rezultātu, svītrkodu lasītājs jāvērš uz svītrkoda vidu, bet to var pavērst jebkurā virzienā.

Jo tuvāk svītrkodam lasītājs ir, jo mazāks ir mērķēšanas stars; jo tālāk no svītrkoda lasītājs atrodas, jo lielāks ir mērķēšanas stars. Ja svītrkods ir mazs, lasītājs jātur tuvu svītrkodam; ja svītrkods ir liels, lasītājs jātur tālāk no svītrkoda, lai to varētu viegli un pareizi nolasīt. Ja svītrkods ir ļoti atstarojošs (piem., ar pārklājumu), lasītāju var nākties pašķiebt, lai nolasītu svītrkodu.

3 1. Skenēšanas lodziņš 1 2. Poga 4 3. LED indikators 2 4. Skaņas signāls 5. Vada izņemšanas caurums 5

Vada izņemšana 1. Lasītāja apakšā atrodiet vada izņemšanas caurumu. 2. Ievietojiet caurumā saspraudi un stingri piespiediet to, tikmēr maigi izvelkot vadu.

Nolasāmība pret sniegumu Katra veida svītrkodam ir savas īpašības. Ar šajā rokasgrāmatā esošo iestatījumu palīdzību aktivizējiet spēju lasīt svītrkodu veidus. Varat lasītājam atspējot tādu svītrkodu veidu lasīšanu, kas netiks izmantoti lasītāja snieguma uzlabošanai

Apkope 1. Skenēšanu var ietekmēt traipi un putekļi uz skenēšanas lodziņa. Ja nepieciešams, izmantojiet labas kvalitātes nepūkojošu drānu/salvetes objektīviem, lai maigi noslaucītu lodziņu. Sliktas kvalitātes papīrs bojās skenēšanas lodziņa virsmas gludumu un ietekmēs lasītāja darbību. 2. Lasītāja korpusu var noslaucīt ar tīru, mīkstu drānu. Pēc nepieciešamības samitriniet drānu ar ūdeni vai vāju ziepju šķīdumu un noslaukiet to ar mīkstu drānu.

12 Problēmu novēršana Q1. Problēma: Datu kabelis ir pareizi uzstādīts, bet LED indikators nedarbojas vai pīkstiens neatskan, kad tiek nospiesta poga. A1. Iespējamie iemesli: Nav strāvas vai kabeļa kļūme. Risinājumi: Pārliecinieties, ka kabelis ir pievienots un lasītājs ir ieslēgts. Izmantojot USB portu, lūdzu, savienojiet USB kabeli ar datora mātesplates USB portu. Neizmantojiet paplašinātu USB portu vai citu USB pagarinātāju. Pārbaudiet, vai kabeļa savienojums nav vaļīgs. Q2. Problēma: Gaisma deg, bet svītrkodu nevar nolasīt. A2. Iespējamie iemesli: Nav iespējots svītrkoda veids, svītrkods ir bojāts vai nav piemērots skenēšanas attālums. Risinājumi: Iespējojiet svītrkoda veidu. Mēģiniet skenēt citus, tāda paša veida svītrkodus. Pietuviniet svītrkodu lasītāju svītrkodam vai attāliniet to. Q3. Problēma: Pēc tam, kad lasītājs nomirgo sarkanā krāsā, skenētie dati resursdatorā tiek parādīti nepareizi. A3. Iespējamie iemesli: Ievades kļūme vai citi lasītāja iestatījumi. Risinājumi: Mainiet ievadi uz noklusējuma angļu valodas ievadi vai atiestatiet lasītāju uz rūpnīcas noklusējumu. Q4. Problēma: Citas situācijas. A4. Iespējamais iemesls: Skenera darbības kļūme. Risinājumi: Izslēdziet un no jauna pareizi savienojiet ierīci un lasītāju. Ieslēdziet ierīces strāvu, atiestatiet lasītāju uz rūpnīcas noklusējumu un no jauna noskenējiet svītrkodu.

Atbalsts Vairāk informācijas par precēm atrodama tīmekļa vietnē www.deltaco.eu. Sazinieties ar mums, izmantojot e-pastu: [email protected].

13 EST - Kasutusjuhend

Ohutusjuhised 1. Ärge vaadake otse seadme valgusesse ega jälgige seda optilise instrumendi abil. 2. Ärge demonteerige ega eemaldage läätse katet. Läätse katte eemaldamisel võivad teie silmad valgusega otse kokku puutuda.

4. Hoidke toode lastest eemal. 5. Ärge laske tootel puutuda kokku löökide, rõhuga ega asetage toodet tulle või sukeldage seda vette. Ärge jätkake toote kasutamist, kui see on kahjustatud või deformeerunud. Ärge jätke seda kuumadesse keskkondadesse.

Tooteteave See vöötkoodiskanner pakub täpset, kiiret ja lihtsat täielikku lahendust andmete sisestamiseks ja säilitamiseks arvuti teabesüsteemides. Tootel on kaks töörežiimi: käsitsi ja automaatandur. Sellel tootel on 4 liidest kõigi host-arvutisüsteemidega ühendamiseks: klaviatuur (klaviatuuri kiil), RS-232, USB HID ja VCOM. seadme väljalülitamise korral. Sellel tootel rohkem seadistusi kui käesolevas kasutusjuhendis saadaval olevad vöötkoodid. Vajadusel võite isiklike seadis- tuste määramiseks luua isiklikke vöötkoode. Üks näide on „Valgusdioodi põlemisaeg“, sellel on umbes 200 võimalikku sead- istust, kuid käesolevas kasutusjuhendis on ainult 4 vöötkoodi näidet. Vastava soovitud loodava või muudetava seadistuse

Vöötkoodide skannimine Skannimise hea efekti saavutamiseks sihtige vöörkoodiriideriga vöörkoodi keskele, kuid võite sihtida suvalisest suunast.

Mida lähemal on skanner vöötkoodile, seda väiksem on sihitav kiir. Mida kaugemal on skanner vöötkoodist, seda suurem on sihitav kiir. Kui vöötkood on väike, peab skanner olema vöötkoodi lähedal. Kui vöötkood on suur, peab skanner olema vöötkoodist kaugemal, et võimaldada vöötkoodi lihtsat ja õiget lugemist. Kui vöötkood on eriti peegelduv (nt kiletatud), võib teil olla tarvis skannerit vöötkoodi lugemiseks kallutada. 3 1. Skannimisaken

1 2. Nupp

4 3. Valgusdiood 2 4. Heliväljund

5. Kaabli eemaldamise ava 5

Kaabli eemaldamine 1. Leidke skanneri all asub kaabli eemaldamise ava. 2. Viige avasse kirjaklamber ja vajutage kirjaklambrile tugevalt , tõmmates samal ajal kaabli õrnalt välja.

Loetavus VS töövõime Igal vöötkoodi tüübil on oma ainulaadsed omadused. Lubage vöötkoodi tüüpide lugemise võime käesolevas kasutusjuhendis leiduvate seadistuste abil. Skanneri töövõime parandamiseks võite keelata skanneril lugeda vöötkoodi tüüpe, mida te ei kasuta.

Hooldus 1. Plekid ja tolm skannimisaknal võivad skannimist mõjutada. Vajadusel kasutage akna puhtaks pühkimiseks kiuvaba lappi / hea kvaliteediga läätsepuhastuspaberit. Halva kvaliteediga paber kahjustab skannimisakna pinna siledust ja mõjutab skanneri efekti. 2. Skanneri korpust võib pühkida puhta pehme lapiga. Vajadusel niisutage lappi vee või õrna seebilahusega ning pühkige seda pehme lapiga.

14 Tõrkeotsing Q1. Probleem: Andmekaabel on õigesti paigaldatud, kuid valgusdioodindikaator või piiksuv heli ei tööta nupule vajutamisel. A1. Võimalikud põhjused: Puuduv toide või kaabli viga. Lahendused: Palun veenduge, et kaabel on ühendatud ja skanner on sisse lülitatud. USB pordi kasutamisel ühendage USB-kaabel arvuti emaplaadil asuvasse USB porti. Ärge kasutage pikendusega USB porti ega muud USB-pikenduskaablit. Kontrollige, et kaabli ühendus ei oleks lõtv. Q2. Probleem: Tuli põleb, kuid vöötkoodi pole võimalik lugeda. A2. Võimalikud põhjused: Vöötkoodi tüüp pole lubatud, kahjustatud vöötkood või ebaõige skannimiskaugus. Lahendused: Lubage vöötkoodi tüüp. Proovige skannida teisi sama vöötkoodi tüübiga vöötkoode. Liigutage vöötkoodiskanner vöötkood- ile lähemale või sellest kaugemale. Q3. Probleem: Skannitud andmed kuvatakse pärast skanneri punast vilkumist hostil valesti. A3. Võimalikud põhjused: Sisendi viga või muud skanneri seadistused. Lahendused: Muutke sisend vaikimisi inglis- keelsele sisendile või taastage skanneri tehase vaikeseadistused. Q4. Probleem: Muud olukorrad. A4. Võimalik põhjus: Skanneri töö viga. Lahendused: Lülitage seade ja skanner välja ning ühendage need uuesti õigesti. Lülitage sisse seadme toide, taastage skanneri tehase vaikeseadistused ja skannige vöötkood uuesti

Tugi Täiendavat tooteteavet leiate aadressil www.deltaco.eu. Võtke meiega ühendust e-posti teel: [email protected].

15 GER - Bedienungsanleitung Sicherheitshinweise 1. Schauen Sie nicht direkt auf das Gerät und beobachten Sie es nicht mit einem optischen Instrument. 2. Zerlegen oder entfernen Sie nicht die Objektivabdeckung. Wenn die Objektivabdeckung entfernt wird, sind Ihre Augen direkt dem Licht ausgesetzt.

4. Halten Sie das Produkt von Kindern fern. 5. Setzen Sie das Produkt keinen Einklemmungen, Druck oder Feuer aus und tauchen Sie es nicht ins Wasser. Verwenden Sie das Produkt nicht weiter, wenn es beschädigt oder verformt ist. Lassen Sie es nicht in heißen Umgebungen.

Produktinformation Dieser Barcodescanner bietet eine genaue, schnelle und einfache Komplettlösung für die Dateneingabe und -speicherung für Computerinformationssysteme. Das Produkt hat zwei Arbeitsmodi: manueller und automatischer Sensor. Dieses Produkt bietet 4 Schnittstellen zum Anschluss an jedes Host-Computersystem: Tastatur (Tastaturkeil), RS-232, USB HID und VCOM. - chert, die auch dann gespeichert werden, wenn das Gerät ausgeschaltet ist.Dieses Produkt hat mehr Einstellungen als ver- fügbare Barcodes in diesem Handbuch. Bei Bedarf können Sie eigene Barcodes erstellen, um Ihre eigenen Einstellungen vorzunehmen. Ein Beispiel ist die „LED-Einschaltzeit“, es hat ungefähr 200 mögliche Einstellungen, aber nur 4 Beispiele von Barcodes gibt es in dieser Bedienungsanleitung. Lesen Sie den englischen - sers“ für die entsprechende Einstellung, die Sie erstellen oder ändern möchten.

Barcodes scannen Um einen guten Scan-Effekt zu erzielen, sollten Sie den Barcode-Leser in der Mitte des Barcodes ausrichten, aber Sie können von jeder Richtung aus zielen.

Je näher der Scanner an dem Barcode ist, desto kleiner ist der Zielstrahl; Je weiter der Scanner vom Barcode entfernt ist,

Wenn der Barcode groß ist, sollte der Scanner weiter vom Barcode entfernt sein, damit der Barcode einfach und korrekt gelesen werden kann.

Barcode zu lesen. 3 1. Scann-Fenster

1 2. Taste 4 3. LED 2 4. Tonausgabe

5. Kabelentfernungsloch 5

Kabel-Entfernung 1. Suchen Sie das Kabelentfernungsloch an der Unterseite des Scanners. 2. Führen Sie eine Büroklammer in das Loch ein und drücken Sie fest auf die Büroklammer, während Sie das Kabel vor- sichtig herausziehen.

Lesbarkeit VS Leistung Jede Art von Barcode hat seine eigenen einzigartigen Eigenschaften. Aktivieren Sie die Möglichkeit, Barcodetypen über die Einstellungen in diesem Handbuch zu lesen. Sie können den Scanner deaktivieren, um Barcode- typen zu lesen, die nicht zur Verbesserung der Scanner-Leistung verwendet werden.

16 Instandhaltung 1. Flecken und Staub auf dem Scanfenster können den Scanvorgang beeinträchtigen. Verwenden Sie ein fusselfreies Tuch / Linsentuch von guter Qualität, um das Fenster bei Bedarf vorsichtig abzuwischen. Schlechte Papierqualität beschä- fekt. 2. Das Gehäuse des Scanners kann mit einem sauberen, weichen Tuch abgewischt werden. Wenn nötig, befeuchten Sie das Tuch mit Wasser oder einer milden Seifenlösung und wischen Sie es mit einem weichen Tuch ab.

Fehlerbehebung Q1. Problem: Das Datenkabel ist korrekt installiert, aber die LED-Anzeige oder der Signalton funktioniert nicht, wenn die Taste gedrückt wird. A1. Mögliche Ursachen: Kein Strom- oder Kabelfehler. Lösungen: Bitte stellen Sie sicher, dass das Kabel angeschlossen und der Scanner eingeschaltet ist. Wenn Sie den USB-Anschluss verwenden, schließen Sie das USB-Kabel an den USB-Anschluss des Computer-Motherboards an. Verwenden Sie keinen erweiterten USB-Anschluss oder ein anderes USB-Verlängerungskabel. Überprüfen Sie, ob die Kabelverbindung lose ist. Q2. Problem: Das Licht ist an, aber der Barcode kann nicht gelesen werden. A2. Mögliche Ursachen: Der Barcode-Typ ist nicht aktiviert, ein beschädigter Barcode oder eine unangemessene Scanentfernung. Lösungen: Aktivieren Sie den Barcode-Typ. Versuchen Sie, andere Barcodes mit dem- selben Barcodetyp zu scannen. Bewegen Sie den Barcode-Scanner näher oder weiter vom Barcode entfernt. Q3. Problem: Die gescannten Daten werden auf dem Host falsch angezeigt, nachdem der Scanner rot blinkt. A3. Mögliche Ursachen: Eingabefehler oder andere Einstellungen für den Scanner. Lösungen: Ändern Sie die Eingabe in die englische Standardeingabe oder stellen Sie den Scanner auf die Werkseinstellungen zurück. Q4. Problem: Andere Situationen. A4. Mögliche Ursache: Scanner-Bedienungsfehler. Lösungen: Schalten Sie das Gerät und den Scanner ordnungsgemäß aus und wieder ein. Schalten Sie das Gerät ein, stellen Sie den Scanner auf die Werkseinstellungen zurück und scannen Sie den Barcode erneut.

Unterstützung www.deltaco.eu. Kontaktieren Sie uns per E-Mail: [email protected].

17 FRA - Notice utilisateur

Consignes de sécurité 1. Ne regardez pas directement ou n’observez pas la lumière de l’appareil à l’aide d’un instrument optique. 2. Ne démontez pas et ne retirez pas le couvre-objectif. Si le couvre-objectif est retiré, vos yeux seront directement exposés à la lumière.

4. Gardez le produit loin des enfants. 5. N’exposez pas le produit aux chocs, à la pression, au feu ou à l’eau. Ne continuez pas à utiliser le produit s’il a été endommagé ou déformé. Ne le laissez pas dans des environnements chauds.

Information sur le produit Ce scanner de codes-barres fournit une solution complète précise, rapide et facile pour la saisie et le stockage de données pour les systèmes d’information informatiques. Le produit dispose de deux modes de fonctionnement : manuel et auto-capteur. Ce produit fournit 4 interfaces pour se connecter à n’importe quel système d’ordinateur hôte : Clavier (Clavier Wedge), RS-232, USB HID et VCOM. qui sont sauvegardés même si l’appareil a été mis hors tension. Ce produit contient plus de paramètres que les codes-barres disponibles dans ce manuel. Si nécessaire, vous pouvez à l’heure », il a environ 200 réglages possibles, mais seulement 4 exemples de codes-barres sont dans ce manuel. Voir la section en anglais « .

Scanner les codes-barres viser le centre du code-barres avec le lecteur de codes-barres, mais vous pouvez viser dans n’importe quelle direction.

Plus le scanner est proche du code-barres, plus le faisceau de visée est petit ; plus le scanner est éloigné du code-barres, plus le faisceau de visée est grand. Si le code-barres est petit, le scanner doit être proche du code-barres ; Si le code- barres est grand, le scanner devra être plus éloigné du code-barres, de sorte que le code-barres puisse être lu facilement et correctement. le code-barres. 3 1. Fenêtre de balayage

1 2. Bouton

4 3. DEL 2 4. Sortie sonore

5 5. Trou de retrait de câble

Retrait du câble 1. Repérez le trou de retrait du câble sur le dessous du scanner. 2. Insérez un trombone dans le trou et appuyez fermement sur le trombone tout en tirant doucement le câble. Lisibilité et performance Chaque type de code à barres possède ses propres propriétés. Activez la possibilité de lire les types de codes à barres via les paramètres de ce manuel. Vous pouvez désactiver le scanner en lisant les types de codes à barres qui ne seront pas utilisés pour améliorer les performances du scanner.

18 Entretien 1. . Les taches et la poussière sur la fenêtre de numérisation peuvent affecter le balayage. Utilisez un chiffon non pelucheux / chiffon optique de bonne qualité pour essuyer délicatement la fenêtre si nécessaire. Un papier de mauvaise qualité endommagera la surface lisse de la fenêtre de numérisation et affectera l’effet du scanner. ou une solution savonneuse douce et essuyez-le avec un chiffon doux.

Dépannage Q1. Problème : Le câble de données est correctement installé, mais le voyant DEL ou le bip sonore ne fonctionne pas lorsque vous appuyez sur le bouton. A1. Causes possibles : Aucune erreur d’alimentation ou de câble. Solutions : Assurez-vous que le câble est connecté et que le scanner est sous tension. Lorsque vous utilisez le port USB, veuillez connecter le câble USB au port USB de la du câble est relâchée. Q2. Problème : La lumière est allumée mais le code-barres ne peut pas être lu. A2. Causes possibles : Le type de code-barres n’est pas activé, le code-barres est endommagé ou la distance de numérisation est incorrecte. Solutions : Activer le type de code-barres. Essayez de numériser d’autres codes-barres avec le même type de code-barres. Déplacez le lecteur de codes-barres plus près ou plus loin du code-barres. Q3. Problème : A3. Causes possibles : Erreur d’entrée ou autres paramètres pour le scanner. Solutions : Changez l’entrée en entrée par défaut entrée anglaise ou restaurez le scanner par défaut. Q4. Problème : D’autres situations. A4. Cause possible : Erreur de fonctionnement du scanner. Solutions : Éteignez et reconnectez correctement l’appareil et le scanner. Allumez l’appareil, restaurez le scanner par défaut et scannez à nouveau le code-barres.

Assistance Plus d’information sur le produit peut être trouvée sur le site www.deltaco.eu. Contactez-nous par e-mail : [email protected].

19 NLD - Gebruiksaanwijzing

Veiligheidsaanwijzingen 1. Kijk niet rechtstreeks in het licht van het apparaat met een optisch instrument. 2. Demonteer of verwijder de lensafdekking niet. Als de lensafdekking is verwijderd, worden uw ogen direct aan het licht blootgesteld.

4. Buiten het bereik van kinderen houden. 5. Beveilig het product tegen schokken of druk, niet in vuur plaatsen of onderdompelen in water. Gebruik het product niet als het beschadigd of vervormd is. Laat het niet in warme omgevingen staan.

Productinformatie Deze streepjescodescanner biedt een nauwkeurige, snelle en eenvoudige complete oplossing voor gegevensinvoer en opslag voor computerinformatiesystemen. Het product heeft twee modi: handmatig en auto-sensor. Dit product biedt 4 interfaces om verbinding te maken met elk host computersysteem: toetsenbord, RS-232, USB HID en VCOM. het wordt opgeslagen, zelfs als het apparaat is uitgeschakeld. Dit product heeft meer instellingen dan beschikbare streepjescodes in deze gebruiksaanwijzing. Indien nodig kunt u uw eigen streepjescodes maken om uw eigen instellingen in te stellen. Een voorbeeld is de “LED op tijd”, deze heeft ongeveer 200 mogelijke instellingen, maar er zijn slechts 4 voorbeelden van streepjescodes in deze gebruiksaanwijzing. Zie het instelling die u wilt maken of wijzigen.

Streepjescodes scannen Om een goed scaneffect te verkrijgen, moet u de streepjescodescanner in het midden van de streepjescode richten, maar u kunt vanuit elke richting richten.

Hoe dichter de scanner bij de streepjescode is, hoe kleiner de richtstraal is, hoe verder weg de scanner van de streep- jescode verwijderd is, hoe groter de richtstraal is. Als de streepjescode klein is, moet de scanner dicht bij de streepjescode staan, als de streepjescode groot is, moet de scanner verder van de streepjescode verwijderd zijn, zodat de streepjescode eenvoudig en correct kan worden gelezen. - jescode te lezen. 3 1. Scanvenster

1 2. Knop

4 3. LED 2 4. Geluidsuitvoer

Kabelverwijderingsopening 5 5.

Kabelverwijdering 1. Zoek de kabelverwijderingsopening aan de onderkant van de scanner. 2. Steek een paperclip in de opening en druk stevig op de paperclip terwijl u de kabel voorzichtig uittrekt.

Uitleesbaarheid versus prestaties Elk type streepjescode heeft zijn eigen unieke eigenschappen. Schakel de mogelijkheid in om streepjescode typen te lezen via de instellingen in deze gebruiksaanwijzing. U kunt de scanner uitschakelen voor het lezen van streepjescode typen die niet worden gebruikt om de prestaties van de scanner te verbeteren.

20 Onderhoud 1. Vlekken en stof in het scanvenster kunnen van invloed zijn op het scannen. Gebruik een pluisvrij doekje/lensdoekje van goede kwaliteit om het venster indien nodig voorzichtig schoon te vegen. Papier van slechte kwaliteit zal de oppervlak- tegladheid van het scanvenster beschadigen en het effect van de scanner beïnvloeden. 2. De behuizing van de scanner kan worden afgeveegd met een schoon, zacht doekje. Wanneer nodig, bevochtig het doekje met water of een milde zeepoplossing en veeg het met een zacht doekje.

Probleemoplossing Q1. Probleem: De datakabel is correct geïnstalleerd, maar de indicator-LED of het piepgeluid werkt niet wanneer op de knop wordt ingedrukt. A1. Mogelijke oorzaken: Geen stroom of er is een kabelfout. Oplossingen: Zorg ervoor dat de kabel is aangesloten en dat de streepjescodescanner is ingeschakeld. Bij gebruik van USB-poort, sluit de USB-kabel aan op de USB-poort van de computer. Gebruik geen verlengde USB-poort of andere USB-verlengkabel. Controleer of de kabelverbinding los zit. Q2. Probleem: Het lampje brandt maar de streepjescode kan niet worden gelezen. A2. Mogelijke oorzaken: Het streepjescodetype is niet ingeschakeld, beschadigde streepjescode of ongepaste scanaf- stand. Oplossingen: Schakel het streepjescode- type in. Probeer andere streepjescodes te scannen met hetzelfde streepjescodetype. Houd de streepjescodescanner dichterbij of verder weg van de streepjescode. Q3. Probleem: De gescande gegevens worden onjuist weergegeven op de host nadat de scanner rood knippert. A3. Mogelijke oorzaken: Invoerfout of andere instellingen voor de scanner. Oplossingen: Wijzig de invoer in de standaard Engelse invoer of herstel de streepjescodescanner naar de fabrieksinstellingen. Q4. Probleem: Andere situaties. A4. Mogelijke oorzaken: Scanner fout. Oplossingen: Schakel het apparaat en de streepjescodescanner correct uit en sluit het opnieuw aan. Schakel het apparaat in, herstel de streepjescodescanner naar de fabrieksinstellingen en scan de streepjescode opnieuw.

Engels.

Klantenservice Meer service en productinformatie vindt u op www.deltaco.eu. Neem contact met ons op via e-mail: [email protected]

21 POL - Instrukcja obsługi

Wskazówki dot. bezpieczeństwa 1. Nie patrz w światło urządzenia ani bezpośrednio, ani za pomocą przyrządu optycznego. 2. Nie demontuj ani nie usuwaj osłony soczewki. Jeśli osłona soczewki zostanie zdjęta, twoje oczy będą bezpośrednio narażone na światło.

4. Trzymać produkt z dala od dzieci. 5. Nie należy narażać produktu na uszkodzenia wstrząsowe, naciskowe lub umieszczać go w pobliżu ognia lub zanurzać w wodzie. Nie należy dalej używać produktu, jeśli został on uszkodzony lub zdeformowany. Nie zostawiaj go w gorącym miejscu.

Informacje o produkcie Ten skaner kodów kreskowych stanowi dokładne, szybkie i proste rozwiązanie do wprowadzania i przechowywania danych przeznaczonych dla komputerowych systemów informatycznych. Produkt ma dwa tryby pracy: ręczny i automatyczny. Ten produkt umożliwia połączenie z dowolnym systemem komputerowego hosta poprzez 4 interfejsy: Klawiaturę (złącze klawiatury), RS-232, USB HID i VCOM.

EEPROM, które są zapisywane, nawet jeśli urządzenie zostanie wyłączone. To urządzenie ma więcej ustawień niż kody kreskowe prezentowane w tym podręczniku. W razie potrzeby możesz utworzyć własne kody kreskowe, aby wprowadzić własne ustawienia. Jednym z przykładów jest „LED na czas”, które ma około 200 the barcode reader” dla odpowiedniego ustawienia czytnika, które chcesz utworzyć lub zmienić.

Skanowanie kodów kreskowych Aby uzyskać odpowiedni efekt skanowania, należy wycelować czytnik kodów kreskowych w środek kodu kreskowego, ale można też celować z dowolnego kierunku.

Im bliżej skanera znajduje się kod kreskowy, tym mniejsza jest wiązka celownicza; im dalej skaner znajduje się od kodu kreskowego, tym większa jest wiązka celownicza. Jeśli kod kreskowy jest mały, skaner powinien znajdować się blisko kodu kreskowego; jeśli kod kreskowy jest duży, skaner powinien znajdować się dalej od kodu kreskowego, aby kod kreskowy mógł być odczytany łatwo i poprawnie. Jeśli kod kreskowy jest mocno odblaskowy (np. powlekany), konieczne może być przechylenie skanera w celu odczytania kodu kreskowego. 3 1. Soczewka skanująca

2. Przycisk 1 4 3. Dioda LED 2 4. Wyjście dźwiękowe

5. Otwór do odłączenia kabla 5

Odłączenie kabla 1. Znajdź otwór do usunięcia kabla u dołu skanera. 2. Włóż spinacz do papieru do otworu i trzymaj go przyciśniętego i jednocześnie delikatnie wyciągnij kabel.

Czytelność VS wydajność Każdy rodzaj kodu kreskowego ma swoje unikalne właściwości. Włącz tryb odczytywania kodów kreskowych za pomocą ustawień podanych w tej instrukcji. Możesz uniemożliwić skanerowi czytanie kodów kreskowych, które nie będą używane, aby poprawić wydajność skanera.

22 Konserwacja 1. Plamy i kurz na szkiełku skanera mogą mieć wpływ na skanowanie. Użyj niestrzępiącej się ściereczki lub chusteczki do soczewek wysokiej jakości, aby w razie potrzeby delikatnie oczyścić szkiełko. Chusteczka gorszej jakości spowoduje uszkodzenie gładkości powierzchni szkiełka i będzie mieć wpływ na efekt skanowania. 2. Obudowa skanera może być wycierana czystą miękką ściereczką. W razie potrzeby, zwilż ściereczkę wodą lub delikat- nym środkiem czyszczącym i przetrzyj ją miękką ściereczką.

Rozwiązywanie problemów Q1. Problem: Kabel do transmisji danych jest poprawnie zainstalowany, ale dioda LED lub sygnał dźwiękowy nie działają po naciśnięciu przycisku. A1. Możliwe przyczyny: Brak zasilania lub błąd kabla. Rozwiązania: Upewnij się, że kabel jest podłączony, a skaner włączony. Jeśli korzystasz z portu USB, podłącz kabel USB do portu USB na płycie głównej komputera. Nie używaj przejściówki USB ani innego przedłużacza USB. Sprawdź, czy kabel nie jest luźno podłączony. Q2. Problem: Światło się zapala, ale kodu kreskowego nie można odczytać. A2. Możliwe przyczyny: Typ kodu kreskowego nie został włączony, kod kreskowy jest uszkodzony lub nieodpowiednia jest odległość skanowania. Rozwiązania: Włącz typ kodu kreskowego. Spróbuj skanować inne kody kreskowe z tym samym typem kodu kreskowego. Przesuń skaner bliżej lub dalej od kodu kreskowego. Q3. Problem: Zeskanowane dane są wyświetlane nieprawidłowo na hoście po tym, jak skaner zamruga na czerwono. A3. Możliwe przyczyny: Błąd wejścia lub inne ustawienia skanera. Rozwiązania: Zmień domyślne wejście na angielskie lub przywróć ustawienia fabryczne skanera. Q4. Problem: Inne sytuacje A4. Możliwa przyczyna: Błąd działania skanera. Rozwiązania: Wyłącz skaner oraz urządzenie w poprawny sposób, a na- stępnie włącz je ponownie. Włącz zasilanie urządzenia, przywróć skaner do domyślnych ustawień fabrycznych i przeskanuj ponownie kod kreskowy.

u jest dostępna tylko w języku angielskim.

Pomoc Więcej informacji o produkcie można znaleźć na: www.deltaco.eu. Skontaktuj się z nami poprzez e-mail: [email protected].

23 Debug mode and factory default The barcode setting “factory default” allows normal output. If you scan “debug mode”, the barcode settings will be output to the host when scanning barcode settings. When “debug mode” is enabled then barcode settings cannot be used to set the scanner. When the scanner is re-powered (after being in “debug mode”), it will return to factory default. After it has returned to factory default you can set the scanner with barcode settings. Note: Please use the “factory default” setting with caution. After scanning “factory default”, the scanner will lose its current settings, and change to factory default settings. For factory default settings and functions see the factory defaults table.

Debug mode Factory default

W401740 WFFD980

Communication Interface Serial communication interface The scanner provides TTL-232 serial communication interface and USB interface to communicate with the host. Via the interfaces, it can receive data, control the instructions from the scanner, and modify the scanner’s settings. The

Baud rate settings Parameters Default Serial Communication Type Standard TTL-232 Baud Rate 9600 Check None Data bits 8 Stop bit 1 Hardware Flow Control None

Baud rate: 9600 Baud rate: 1200

WFFD9D3 WFFD9D0 Baud rate: 2400 Baud rate: 19200

WFFD9D1 WFFD9D5 Baud rate: 38400 Baud rate: 4800

WFFD9D6 WFFD9D2 Baud rate: 57600 Baud rate: 14400

WFFD9D7 WFFD9D4 Baud rate: 115200

WFFD9D8 24 USB interface When the scanner is connected to the host by USB cable, the scanner will use USB DATAPIPE MODE automatically.

USB DATAPIPE USB DATAPIPE is a custom USB transport protocol. This feature requires the installation of the corresponding driver on the host.

Switch to USB DATAPIPE mode

W030D00

USB HID-KBW When using the USB interface, you can simulate the scanner to be a HID-KBW (keyboard wedge). In this mode, the scanner will become a virtual keyboard and output data to the host.

Switch to USB HID-KBW mode

W030D01 Standard keyboard input mode Standard keyboard input mode is the factory default setting. The scanner has two more input modes: Keyboard characters emulation mode and keyboard control characters emulation mode.

Switch to standard keyboard input mode

W066000 Keyboard characters emulation mode This mode allows ASCII characters (16 hexadecimal values from 0x00 to 0xFF) in any language. This mode has a large data output, resulting in a slow down in speed. In this mode when ASCII characters are input, the scanner will read the barcodes as a virtual keyboard like this: (1) Press and hold “ALT”. (2) According to the character code, input the number keys in the digital keyboard in turns. (3) Release “ALT”.

Switch to keyboard character emulation mode

W066004 Note: It is recommended that you turn Num Lock on the main numeric keypad before enabling this mode. Keyboard control characters emulation mode Hexadecimal ASCII values from 0x00 to 0x1F can be matched to control function keys, when emulating keyboard, control function keys: (1) Press and hold “Ctrl”. (2) Press the control keys (for matching keys see table: Emulation keyboard control characters pairing table. (3) Release “Ctrl” and control keys.

Switch to keyboard control characters emulation mode

W066002

25 Emulation keyboard control characters pairing table ASCII Value (HEX) Function Key ASCII Value (HEX) Function Key 00 2 10 P 01 A 11 Q 02 B 12 R 03 C 13 S 04 D 14 T 05 E 15 U 06 F 16 V 07 G 17 W 08 H 18 X 09 I 19 Y 0A J 1A Z 0B K 1B [ 0C L 1C \ 0D M 1D ] 0E N 1E 6 0F O 1F .

Keyboard language layout Change layout by using the barcode settings. The default is US English.

1. US English 2. Belgium

WFF6B00 WFF6B01 3. Brasil 4. Canada

WFF6B02 WFF6B03 5. Czechoslovakia 6. Denmark

WFF6B04 WFF6B05 7. Finland 8. France

WFF6B06 WFF6B07 9. Austria 10. Greece

WFF6B08 WFF6B09 1 1. Hungary 12. lsrael

WFF6B0A WFF6B0B

26 13. ltaly 14. Latin American Spanish layout

WFF6B0C WFF6B0D 15. Netherlands 16. Norway

WFF6B0E WFF6B0F 17. Poland 18. Portugal

WFF6B10 WFF6B11 19. Romania 20. Russia

WFF6B12 WFF6B13 21. Slovakia 22. Spain

WFF6B15 WFF6B16 23. Sweden 24. Switzerland

WFF6B17 WFF6B18 25. Turkey1 26. Turkey2

WFF6B19 WFF6B1A 27. Britain 28. Japan

WFF6B1B WFF6B1C Unknown character tone Unknown characters are a few characters (in some languages) on barcodes that will not show in the host’s system and cannot be sent to the host. Use the following barcode settings to set whether the scanner sends an error tone or not when it has scanned an unknown character. If you scan “no-warning tone”, there will be no warning tone when an unknown character is scanned. If you scan “warning tone”, there will be a warning tone when the barcode has unknown characters.

Warning tone No-warning tone

W080E08 W080E00

Press and release key interval delay Press and release key interval is the time between releasing a key and pressing a key. 0ms 5ms

WC06F00 WC06F40 27 10ms 15ms

WC06F80 WC06FC0 Caps Lock “Turn on Caps Lock” inverts the letter case in the barcode. Similar to using Caps Lock on a regular keyboard. Note: If “Keyboard emulation characters mode” or “Change to uppercase/lowercase” is active, this function is not valid. Example output: If you scan “AbC”, the host will receive “aBc”. Turn off Caps Lock Turn On Caps Lock

W086000 W086008 Change to uppercase/lowercase If you scan “convert all to uppercase”, all the letters in the barcode will change to uppercase. If you scan “convert all to lowercase”, all the letters in the barcode will change to lowercase.

No case conversion Convert all to lowercase Convert aII to uppercase

W306F00 W306F30 W306F20 Emulate Num Lock When Num Lock is turned on the scanner converts the numbers 0 to 9 to the Numeric Pad equivalent. When Num Lock is turned off the scanner does not convert the numbers.

Turn on Num Lock Turn off Num Lock *

W046F04 W046F00 Emulate COM port via USB Connect the scanner to the host via USB. Scan the “Emulate COM port via USB” barcode to allow the host to receive data like a serial port. You need to set barcode settings on the scanner to match the host’s requirements. A driver for the host is required for this. Emulate COM port via USB

W030D02 Enable HID-POS . Features: 1. HID based, no custom driver required.

Note: HID-POS does not require a custom driver. However, a HID interface on Windows 98 does. All HID interfaces employ standard driver provided by the operating system. Use defaults when installing the driver. Enable HID-POS

W030D03

28 Scan modes Manual mode Manual mode (default/normal): Trigger pulls activates scanning. The scanning continues until the barcode is fully scanned or the trigger is released.

Manual mode

W030000 Continuous mode Continuous mode: The scanner automatically activates next scan. The scan continues until the barcode is scanned or the scanning timeout expires. When a scan is completed, the scanner waits for the scanning timeout to expire and then starts next scan. The scanner continues to work in this pattern until no barcode is presented to the scanner, then the scanner will automatically stop scanning. Pressing the trigger will stop/resume scanning. Continuous mode

W030002 Scanning timeout Sets the maximum time for a scan during a scan attempt. It can be set in 0.1s increments from 0.1s to 25.5s. The default timeout is 5.0s. If it is set to 0s, the scanner will scans barcodes continuously. For more information, see Appendix D: Examples. Scanning timeout

M00031D Timeout between scans Sets the timeout between scans. When a scan ends, next scan will not start until the timeout between scans expires. It is pro- grammable in 0.1s increments from 0.1s to 25.5s. The default timeout is 1.0s. For more information, see Appendix D: Examples.

Timeout between scans

M00031C Automatic light sense mode In this mode, the scanner will wait for the light timeout to expire before activating a scan every time it detects a change in ambient light. The scanning continues until the barcode is scanned or the scanning timeout expires. After a scan ends, the scanner waits for the timeout between scans to expire before beginning to monitor ambient light. If no barcode is presented to the scanner, the scanner will automatically stop scanning and start to monitor ambient light. In this mode, a trigger pull can also activate a scan. The scanning continues until the barcode is scanned or the trigger is released. When the scan ends, the scanner will continue to monitor ambient light. Example usage: Useful when placing the scanner static and moving barcodes in front of the scanner. If the light in the room is not high enough, automatic light sense mode may not work properly. Automatic light sense mode

W030003

29 Light sense timeout The scanner waits for the light sense timeout to expire before activating ambient light monitoring. This can be set in 0.1s increments from 0.1s to 25.5s. The default timeout is 0.4s. For more information, see Appendix D: Examples.

Light sense timeout

M00031B Light sensitivity ’s response to changes in ambient light. The higher the default setting is medium light sensitivity. Light sensitivity levels range from 0 to 255. The smaller the number, the higher the light sensitivity. . For more information, see Appendix D: Examples.

High light sensitivity Medium light sensitivity

WFF0308 WFF0320 Low light sensitivity Custom light sensitivity

WFF0340 M00031A Host command trigger mode In this mode scanning is activated by host commands (i.e. set the bit0 of register 0x0002 to “1”). The scanning continues until the barcode is scanned or the scanning timeout expires.

Host command trigger mode

W030001 LED & aiming

LED Changing LED settings can improve the light conditions during scanning. Normal (default): LED is turned on during scanning. Always on: LED stays on when the scanner is powered on. Always off: LED stays off all the time.

Normal Always off Always on

W0C0004 W0C0000 W0C000C Aiming When scanning, the scanner projects an aiming beam, which makes scanning easier. Normal (default): The scanner projects an aiming beam only during barcode scanning. Always on: The aiming beam is constantly on when the scanner is powered on. Always off: The aiming beam is off all the time. Normal Always off Always on

W300010 W300000 W300030

30 Enable mute mode Disable mute mode

W400000 W400040

Good scan tone Good read tones: On Good scan tone: Off

W040E04 W040E00 Good scan tone frequency

Low Medium High

WFF09DA WFF094B WFF0925 Good scan tone duration 40ms 80ms 120ms

WFF0A1F WFF0A3E WFF0A5D

Good scan LED Good scan LED: On Good scan LED: Off

W800080 W800000 Data formatting The scanner supports the following format: [“F”/ “S”] + [Code ID] + [AIM ID] + [DATA] + [terminating character]

When enabled, if a barcode is not successfully scanned, “F” is transmitted; if a scan is successful (“Good scan”), “S” is appended to the barcode data as the most left character. Note: This function is invalid in USB DATAPIPE MODE.

W400240 W400200

AIM ID table. If AIM ID

WFFD9C0 WFFD9C1 31 Barcode ID can be used to identify barcode type. For more information, see barcode ID table. User can choose to transmit barcode ID or visible barcode ID by scanning respective barcode. See barcode ID table.

W800280 W800200 Transmit barcode ID Transmit visible barcode ID

W018A00 W018A01

A terminating character such as carriage return (CR) or carriage return/line feed pair (CRLF) or horizontal tab (TAB) can be used to mark the end of data. Append CR

W616000 W616001 Append CRLF Append TAB

W616021 W616041 Symbologies Global settings Enable/Disable all symbologies If all symbologies are disabled, the scanner can only identify barcodes that has barcode settings.

Enable All Symbologies Disable All Symbologies

WFFD981 WFFD982 Enable/Disable 1D symbologies The following barcode settings, only applies to 1D type barcodes.

Enable 1D symbologies Disable 1D Symbologies

WFFD983 WFFD984 Enable/Disable 2D symbologies The following barcode settings, only applies to 2D type barcodes.

Enable 2D symbologies Disable 2D symbologies

WFFD985 WFFD986

32 Inverse/regular barcodes Regular barcode: Dark image on a bright background. Inverse barcode: Bright image on a dark background. Barcode inverse on: Read both regular barcodes and inverse barcodes. Barcode reverse off (default): Read regular barcodes only. The scanner shows a slight decrease in scanning speed when barcode inverse is on.

Barcode inverse: On Barcode inverse: Off

W100210 W100200 1D symbologies Restore factory defaults of Code 128 Enable Code 128 Disable Code 128

WFFD990 W011601 W011600 UCC/EAN-128 (GSl-128) Restore factory defaults of UCC/EAN-128 Enable UCC/EAN-128 Disable UCC/EAN-128

WFFD991 W011701 W011700

AIM 128 Restore factory defaults of AIM 128 Enable AIM 128 Disable AIM 128

WFFD992 W101610 W101600 Add-on barcodes EAN-8 / EAN-13 / UPC-E / UPC-A

In the examples: The parts without dotted lines are the base/standard barcodes while the parts surrounded by dotted lines are the barcode add-ons. Examples:

When 2-digit add-on and 5-digit add-on are enabled, the scanner can scan barcodes both with add-ons (2 and 5) and without add-ons (2 and 5). When both are disabled, the scanner will ignore the add-on part of the barcodes. The scanner

The same applies for EAN-8 / EAN-13 / UPC-E / UPC-A. EAN-8 EAN-8 is 8 digits in length. The last digit is a check digit used to verify the integrity of the data. Restore factory defaults of EAN-8

WFFD994

33 Enable/Disable EAN-8 Enable EAN-8 Disable EAN-8

W011301 W011300 Transmit EAN-8 check digit Do not transmit EAN-8 check digit

W041304 W041300 Enable 2-digit add-on barcodes Disable 2-digit add-on barcodes

W101310 W101300 Enable 5-digit add-on barcodes Disable 5-digit add-on barcodes

W201320 W201300 EAN-8 add-on barcodes required EAN-8 add-on barcodes not required

W081308 W081300 Extend EAN-8 to EAN-13

Enable extend EAN-8 to EAN-13 Disable extend EAN-8 to EAN-13

W401340 W401300 EAN-13 EAN-13 is 13 digits in length. The last digit is a check digit used to verify the integrity of the data.

Restore factory defaults of EAN-13 Enable EAN-13

WFFD995 W011101 Disable EAN-13 Transmit EAN-13 check digit

W011100 W041104 Do not transmit EAN-13 check digit Enable 2-digit add-on barcodes

W041100 W101110 Disable 2-digit add-on barcodes Enable 5-digit add-on barcodes

W101100 W201120

34 Disable 5-digit add-on barcodes EAN-13 add-on barcode required

W201100 W081108 EAN-13 add-on barcode not required

W081100 ISSN Restore factory defaults of ISSN Enable ISSN Disable ISSN

WFFD996 W401140 W401100 ISBN Restore factory defaults of ISBN Enable ISBN

WFFD997 W011201 Disable ISBN Enable ISBN-13

W011200 W041200 Enable ISBN-10

W041204 UPC-E UPC-E is 8 digits in length. The last digit is a check digit used to verify the integrity of the data.

Restore factory defaults of UPC-E Enable UPC-E

WFFD998 W011501 Disable UPC-E Transmit UPC-E check digit

W011500 W041504 Do not transmit UPC-E check digit Enable 2-digit add-on barcodes

W041500 W201520 Disable 2-digit add-on barcodes Enable 5-digit add-on barcodes

W201500 W401540

35 Disable 5-digit add-on barcodes UPC-E add-on barcodes required

W401500 W101510 UPC-E add-on barcodes not required Transmit system character “0”

W101500 W081508 Do not transmit system character “0” Enable UPC-E add-on

W081500 W801580 Disable UPC-E add-on

W801500 UPC-A UPC-A is 13 digits in length. The last digit is a check digit used to verify the integrity of the data. Note: The preamble character “0” usually does not appear in printed UPC-A barcodes. Restore factory defaults of UPC-A

WFFD999 Enable UPC-A Disable UPC-A

W011401 W011400 Transmit UPC-A check digit Do not transmit UPC-A check digit

W041404 W041400 Enable 2-digit add-on barcodes Disable 2-digit add-on barcodes

W201420 W201400 Enable 5-digit add-on barcodes Disable 5-digit add-on barcodes

W401440 W401400 UPC-A add-on barcodes required UPC-A add-on barcodes not required

W101410 W101400 Do not transmit preamble character “0” Do not transmit preamble character “0”

W081408 W081400 36 If an Interleaved 2 of 5 barcode contains an odd number of characters, a leading zero must be appended. Scan the appro- priate barcode to choose whether to transmit the appended “0”. Interleaved 2 of 5 has an optional last check digit. The check digit is used to verify the integrity of the data. check digit. Barcodes passing the check will be transmitted except the last digit, barcodes failing will not be transmitted.

Barcodes passing the check will be transmitted, barcodes failing will not be transmitted. Restore factory defaults of Interleaved 2 of 5

WFFD99A Enable Interleaved 2 of 5 Disable Interleaved 2 of 5

W011801 W011800 Disable check digit

W0C1800

W0C1804 W0C180C Transmit appended “0” Do not transmit appended “0”

W101800 W101810 ITF-6 ITF-6 is a special kind of Interleaved 2 of 5 with a length of 6 characters and the last character as the check digit. Note: We recommend that you do not enable ITF-6 and Interleaved 2 of 5 at the same time. Restore factory defaults of ITF-6 Disable ITF-6

WFFD99B W011900 Enable ITF-6 but do not transmit check digit Enable ITF-6 and transmit check digit

W051901 W051905 ITF-14 ITF-14 is a special kind of Interleaved 2 of 5 with a length of 14 characters and the last character as the check digit. Note: We recommend that you do not enable ITF-14 and Interleaved 2 of 5 at the same time.

Restore factory defaults of ITF-14 Disable ITF-14

WFFD99C W201800

37 Enable ITF-14 but do not transmit check digit Enable ITF-14 and transmit check digit

WA01820 WA018A0 Matrix 2 of 5 Restore factory defaults of Matrix 2 of 5 Enable Matrix 2 of 5

WFFD99F W011A01 Disable Matrix 2 of 5 Disable check digit

W011A00 W041A00

W0C1A04 W0C1A0C Industrial 25 Restore factory defaults of Industrial 25 Enable Industrial 25

WFFD9A0 W081908 Disable Industrial 25 Disable check digit

W081900 W201900

W601920 W601960 Standard 25 Restore factory defaults of Standard 25 Enable Standard 25

WFFD9A1 W101A10 Disable Standard 25 Disable check digit

W101A00 W401A00

WC01A40 WC01AC0

38 Code 39 Code 39 barcodes have a character as start and stop character, they can be transmitted or not transmitted. The scanner can be set to identify all ASCII characters. See barcodes: Enable/Disable Code 39 full ASCII.

Restore factory defaults of Code 39

WFFD9A2 Enable Code 39 Disable Code 39

W011C01 W011C00 Transmit start/stop character Do not transmit start/stop character

W041C04 W041C00 Disable check digit

W081C00

W181C08 W181C18 Enable Code 39 full ASCII Disable Code 39 full ASCII

W201C20 W201C00 Codabar barcodes may have a character as start and stop character, they can be transmitted or not transmitted. Start and stop characters can be set to these formats: ABCD/ABCD, ABCD/TN*E, abcd/abcd, abcd/tn*e. Restore factory defaults of Codabar

WFFD9A3 Enable Codabar Disable Codabar

W011E01 W011E00 Disable check digit

W101E00

W301E10 W301E30

39 Transmit start/stop character Do not transmit start/stop character

W021E02 W021E00 ABCD/ABCD as start/stop character ABCD/TN*E as start/stop character

W0C1E00 W0C1E04 abcd/abcd as start/stop character abcd/tn*e as start/stop character

W0C1E08 W0C1E0C Restore factory defaults of Code 93 Enable Code 93

WFFD9A4 W081208 Disable Code 93 Disable check digit

W081200 W201200

W601220 W601260 Restore factory defaults of Code 11

WFFD9A5 Enable Code 11 Disable Code 11

W011D01 W011D00 Disable check digit One check digit, MOD 11

W1C1D00 W1C1D04 Two check digits, MOD11/MOD 11 Two check digits, MOD11/MOD9

W1C1D08 W1C1D0C One check digit, MOD 11 (Length<=11) One check digit, MOD 11 (Length<=11) Two check digits, MOD 11/MOD 11 (Length>11) Two check digits, MOD11/MOD9 (Length>11)

W1C1D10 W1C1D14 40 Transmit check digit Do not transmit check digit

W201D20 W201D00 Restore factory defaults of Plessey Enable Plessey

WFFD9A6 W011F01 Disable Plessey Disable check digit

W011F00 W021F00

W061F02 W061F06

MSI-Plessey Restore factory defaults of MSI-Plessey

WFFD9A7 Enable MSI-Plessey Disable MSI-Plessey

W081F08 W081F00 Disable check digit One check digit, MOD10

W301F00 W301F10 Two check digits, MOD10/MOD10 Two check digits, MOD10/MOD11

W301F20 W301F30 Transmit check digit Do not transmit check digit

W401F40 W401F00 GS1 DataBar (RSS-14) Restore factory defaults of GS1 DataBar

WFFD9A8

41 Enable GS1 DATABAR Disable GS1 DATABAR

W011B01 W011B00

W041B04 W041B00

GS1 DataBar Limited Restore factory defaults of GS1 DataBar Limited

WFFD9A9 Enable GS1 DataBar Limited Disable GS1 DataBar Limited

W081B08 W081B00

W201B20 W201B00 GS1 DataBar Expanded Restore factory defaults of GS1 DataBar Expanded

WFFD9AA Enable GS1 DataBar Expanded Disable GS1 DataBar Expanded

W401B40 W401B00 2D Symbologies PDF417 Restore factory defaults of PDF417

WFFD9B0 Enable PDF417 Disable PDF417

W010C01 W010C00

Data Matrix Restore factory defaults of Enable Data Matrix

WFFD9B1 W080C08 42 Disable Data Matrix Enable scanning of rectangular barcodes

W080C00 W034B03 Disable scanning of rectangular barcodes Enable unmirrored Data Matrix Only

W034B00 W0C4A00 Enable mirrored Data Matrix Only Enable both mirrored and unmirrored Data Matrix

W0C4A04 W0C4A0C QR Code Restore factory defaults of QR Code

WFFD9B2 Enable QR Code Disable QR Code

W800D80 W800D00 Enable Micro QR Disable Micro QR

W049904 W049900 Enable mirrored Micro QR Disable mirrored Micro QR

W089908 W089900

Factory defaults table Setting Factory Default (Remarks) Programming Barcode Barcode programming Barcode programming Programming barcode data Programming Barcode Data Communication Interfaces Baud Rate 9600. Parity Check None. TTL-232 Number of Data Bits 8. Number of stop bits 1. None. USB Interface USB data pipe (Options: USB HID-KBW, USB COM Port Interface Emulation, HID-POS.) 43 Input mode Standard Keyboard. Keyboard layout U.S. Tone on unknown character Enabled. USB HID-KBW Inter-keystroke delay No delay. Caps Lock Disabled. Convert Case No conversion. Emulate Numeric Keypad Disabled. Scan modes Default scan mode Manual mode Timeout between scans 1.0s. (0-25.5s). Continuous mode Scanning timeout Timeout between scans 1.0s. (0-25.5s). Scanning timeout Light sense mode Light sense timeout 0.4s. (0-25.5s). Light sensitivity Medium. Host command trigger mode Scanning timeout LED & aiming LED Normal. (Turn on when scanning barcode) Aiming Normal. (Turn on when scanning barcode.)

Mute mode Disabled. Tone on good scan Enabled. Good scan tone Tone frequency Medium. Tone duration 80ms (Other options: 40ms and 120ms.) Good scan LED Enabled. Disabled. (“S”: Good scan; “F”: No scan. Not applicable to USB Data pipe.) Data Formatting Disabled. Disabled. Code ID type Original Code ID. Disabled (Terminating character options: CR, CRLF, TAB.) Symbologies Barcode inverse Disabled. (Applicable to all symbologies.) Code 128 Code 128 Enabled. UCC/EAN-128 (GS1-128) UCC/EAN-128 Enabled.

44 AIM 128 AIM 128 Enabled. EAN-8 EAN-8 Enabled. Check digit Transmit. 2-digit add-on code Disabled. 5-digit add-on code Disabled. Add-on code Not required. Extend to EAN-13 Disabled. EAN-13 EAN-13 Enabled. Check digit Check digit. 2-digit Add-on code Disabled. 5-digit Add-on code Disabled. Add-on code Not required. ISSN ISSN Disabled. ISBN ISBN Enabled. ISBN format ISBN-13. UPC-E UPC-E Enabled. Check digit Transmit. 2-digit add-on code Disabled 5-digit add-on code Disabled. Add-on code Not required. Extend to UPC-A Disabled. System character “0” Do not transmit. UPC-A UPC-A Enabled. Check digit Transmit. 2-digit add-on code Disabled. 5-digit add-on code Disabled. Add-on code Not required. Preamble character “0” Do not transmit. Interleaved 2 of 5 Interleaved 2 of 5 Enabled.

45 Disabled. Check digit Do not transmit. Transmit (For Interleaved 2 of 5 barcodes that contain an Appended “0” odd number of characters.) ITF-6 ITF-6 Disabled. Check digit Do not transmit. ITF-14 ITF-14 Enabled. Check digit Transmit. Matrix 2 of 5 Matrix 2 of 5 Enabled. Disabled. Check digit Do not transmit. Industrial 25 Industrial 25 Enabled. Disabled. Check digit Do not transmit. Code 39 Code 39 Enabled. Disabled. Check digit Do not transmit. Start/stop character Do not transmit. Code 39 full ASCII Disabled. Codabar Codabar Enabled. Disabled. Check digit Do not transmit. Start/stop character Transmit. Start/stop character format ABCD/ABCD. Code 93 Code 93 Enabled. Enabled. Check digit Do not transmit. Code 11 Code 11 Enabled. One check digit, MOD11. Check digit Transmit.

46 Plessey Plessey Enabled. Enabled. Check digit Do not transmit. MSI-Plessey MSI-Plessey Enabled. One check digit, MOD10. Check digit Transmit. GS1 DATABAR GS1 DATABAR Enabled. Transmit. GS1 DataBar Limited GS1 DataBar Limited Enabled. Transmit. GS1 DataBar Expanded GS1 DataBar Expanded Enabled. PDF417 PDF417 Enabled. Data Matrix Data Matrix Enabled. Rectangular barcodes Decode. Mirror images Scan unmirrored Data Matrix only. QR Code QR Code Enabled. Micro QR Enabled. Mirrored Micro QR Do not decode

AIM ID table Symbology Remark Code 128 AIM ID: ]C0 Standard Code 128. UCC/EAN 128 (GS1-128) AIM ID: ]C1 FNC1 is the character right after the start character. AIM 128 AIM ID: ]C2 FNC1 is the 2nd character after the start character. EAN-8 AIM ID: ]E4 Standard EAN-8. AIM ID: ]E4....]E1… EAN-8 + 2-digit add-on code. 47 AIM ID: ]E4....]E2… EAN-8 + 5-digit add-on code. EAN-13 AIM ID: ]E0 Standard EAN-13. AIM ID: ]E3 EAN-13 + 2/5-digit add-On code. ISSN AIM ID: ]X5 Standard ISSN. ISBN AIM ID: ]X4 Standard ISBN. UPC-E AIM ID: ]E0 Standard UPC-E. AIM ID: ]E3 UPC-E + 2/5-digit add-on code. UPC-A AIM ID: ]E0 Standard UPC-A. AIM ID: ]E3 UPC-A + 2/5-Digit add-on code. Interleaved 2 of 5 AIM ID: ]I0 AIM ID: ]I1 AIM ID: ]I3 ITF-6 AIM ID: ]I1 Transmit check digit. AIM ID: ]I3 Do not transmit check digit. ITF-14 AIM ID: ]I1 Transmit check digit. AIM ID: ]I3 Do not transmit check digit. Matrix 2 of 5 AIM ID: ]X1 AIM ID: ]X2 AIM ID: ]X3 Industrial 25 AIM ID: ]S0 Standard 25 AIM ID: ]R0 AIM ID: ]R8 One check digit, MOD 7; do not transmit check digit. AIM ID: ]R9 One check digit, MOD 7; transmit check digit. Code 39 AIM ID: ]A0 AIM ID: ]A1 One check digit, MOD 43; transmit check digit. AIM ID: ]A3 One check digit, MOD 43; do not transmit check digit.

48 AIM ID: ]A4 AIM ID: ]A5 Full ASCII enabled; MOD43; transmit check digit. AIM ID: ]A7 Full ASCII enabled; MOD43; do not transmit check digit. Codabar AIM ID: ]F0 Standard Codabar. AIM ID: ]F2 AIM ID: ]F4 Code 93 AIM ID: ]G0 Code 11 AIM ID: ]H0 One check digit, MOD11; transmit check digit. AIM ID: ]H1 Two check digits, MOD11/MOD11 ; transmit check digit. AIM ID: ]H3 AIM ID: ]H8 Two check digits, MOD l l/MOD9; transmit check digit. AIM ID: ]H9 Plessey AIM ID: ]P0 MSI Plessey AIM ID: ]M0 One check digit, MOD1O; transmit check digit. AIM ID: ]M1 One check digit, MOD1O; do not transmit check digit. AIM ID: ]M7 Two check digits, MOD1O/MOD11 ; do not transmit check digit. AIM ID: ]M8 Two check digits, MOD1O/MOD11 ; transmit check digit. AIM ID: ]M9 GS1 DATABAR, GS1 DataBar Limited, GS1 DataBar Expanded AIM ID: ]e0 Standard PDF417 AIM ID: ]L0 Data Matrix AIM ID: ]d0 ECC 000 - 140. AIM ID: ]d1 ECC 200. AIM ID: ]d2 ECC 200; FNC1 is the 1st or 5th character after the start character. AIM ID: ]d3 ECC 200; FNC1 is the 2nd or 6th character after the start character. AIM ID: ]d4 ECC 200, ECI protocol supported. AIM ID: ]d5 ECC 200; FNC1is the 1st or 5th character after the start character; ECI supported. AIM ID: ]d6 ECC 200; FNC1 is the 2nd or 6th character after the start character; ECI supported. QR Code AIM ID: ]Q0 AIM ID: ]Q1 QR2 (2005 symbol), ECI protocol not supported.

49 AIM ID: ]Q2 QR2 (2005 symbol), ECI protocol supported. AIM ID: ]Q3 QR2 (2005 symbol), ECI protocol not supported; FNC1 is the character right after the start character. AIM ID: ]Q4 QR2 (2005 symbol), ECI protocol supported; FNC1 is the character right after the start character. AIM ID: ]Q5 QR2 (2005 symbol), ECI protocol not supported; FNC1 is the 2nd character right after the start character. AIM ID: ]Q6 QR2 (2005 symbol), ECI protocol supported; FNC1 is the 2nd character right after the start character.

Barcode ID table Symbology Barcode ID Visible ID Code 128 FNC3 1 A(0x41) Code 128 2 B(0x42) UCC/EAN 128 3 C(0x43) EAN-8 4 D(0x44) EAN-13 5 E(0x45) UPC-E 6 F(0x46) UPC-A 7 G(0x47) Interleaved 2 of 5 8 H(0x48) ITF-14 9 I(0x49) ITF-6 10 J(0x4A) Code 39 13 M(0x4D) Codabar 15 O(0x4F) Standard 25 16 P(0x50) Code 93 17 Q(0x51) AIM 128 21 U(0x55) MSI Plessey 22 V(0x56) ISBN 23 W(0x57) Industrial 25 24 X(0x58) Matrix 2 of 5 25 Y(0x59) GS1 DATABAR 26 Z(0x5A) GS1 DATABAR Limited 27 [(0x5B) GS1 DATABAR Expand 28 \(0x5C) Code 11 29 ](0x5D) Plessey 30 ^(Qx5E) ISSN 31 _(0x5F) PDF417 32 `(0x60) QR 33 a(0x61) Data Matrix 35 c(0x63)

50 Appendix D: Examples The following examples show you how to set some scanner settings by scanning barcode settings. Set the scanning timeout Set the Light sense timeout Example: Set the scanning timeout to 5.0s Example: Set the light sense timeout to 5.0s 1. Scan the scanning timeout barcode. 1. Scan the light sense Timeout barcode. 2. Scan the “digit barcodes” 5 and 0. 2. Scan the “digit barcodes” 5 and 0. 3. Scan save barcode. 3. Scan save barcode. Set the timeout between decodes Set the light sensitivity level Example: Set the timeout between scans to 5.0s Example: Set the light sensitivity level to 5 1. Scan the timeout between scans barcode. 1. Scan the custom sensitivity barcode. 2. Scan the “digit barcodes” 5 and 0. 2. Scan the “digit barcode” 5. 3. Scan save barcode. 3. Scan save barcode. Digit barcodes 0-9 / A-F

0 1

D000000 D000001 2 3

D000002 D000003 4 5

D000004 D000005 6 7

D000006 D000007 8 9

D000008 D000009 A B

D00000A D00000B C D

D00000C D00000D E F

D00000E D00000F

51 Save/Cancel Barcodes After reading numeric barcode(s), you need to scan the save barcode to save the data. If you scan the wrong digit(s), you can either scan the cancel the last digit barcode and then the correct digit, or scan the cancel all digits barcode and then the digits you want. For example if you scan the scanning timeout barcode and then the numeric barcodes “1 “, “2” and “3”, and then: Cancel the last digit: the last digit “3” will be removed. Cancel all digits: all digits “ 123” will be removed.

Save barcode Cancel the last digit Cancel all digits

D000012 D000010 D000011

52 A N O R D I C B R A N D

EN: [email protected]

SE: [email protected] 0200-877771

FI: 020 712 0390 DK: [email protected]

NO: [email protected]

SweDeltaco AB, Glasfibergatan 8, 5tr, 125 45 Älvsjö, Sweden