99-7301 INSTALLATION Radio Housing "B" INSTRUCTIONS
Total Page：16
File Type：pdf, Size：1020Kb
KIT COMPONENTS Radio Housing "A" 99-7301 INSTALLATION Radio Housing "B" INSTRUCTIONS Radio Housing "C" APPLICATIONS CAR PAGE Radio Housing "D" HYUNDAI Accent 1995-99........................................................... 1 Elantra 1992-95.......................................................... 1 Excel 1986-89............................................................. 2 Excel 1990-94............................................................. 2 Spacer Set "A" Scoupe 1991-95...........................................................3 Spacer Set "B" Sonata 1995-98...........................................................3 Tiburon 1997-02..........................................................4 MITSUBISHI (4) Oval-Head Screws (4) Plugs Precis 1986-89............................................................ 5 Precis 1990-93............................................................ 4 (4) Pan-Head (4) Washers Screws TOOLS REQUIRED Phillips screwdriver 1-800-221-0932 www.metraonline.com Rev.201202 Cutting tool © COPYRIGHT 2001 METRA ELECTRONICS CORPORATION HYUNDAI Accent 1995-99 45 A 12 B C D A) Strip wire ends back ½" B) Twist ends together "A" C) Solder D) Tape Locate the factory wiring harness in the Disconnect the negative battery terminal to Locate Radio Housing "D". Locate the (4) dash. Metra recommends using the Locate the mounting positions in the sub-dash. prevent an accidental short circuit. Remove factory screws previously removed in step proper mating adaptor and making the ashtray and (2) Phillips screws exposed. #1 and retain for use in step #6. Skip to the connections as shown. (Isolate and Disconnect (2) vent cables from the vent Installation Instructions for ALL VEHICLES individually tape off the ends of any levers located behind the driver's side dash. on Page #6. unused wires to prevent electrical short Unclip the dash trim bezel and disconnect circuit). the wiring. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. 6 HYUNDAI Elantra 1992-95 12 Fig. A Fig. B Convert Radio Housing "A" by cutting along the v-cut on each mounting tab and Disconnect the negative battery terminal to removing the indicated segments. Attach ACCENT, ELANTRA, EXCEL, PRECIS, SCOUPE, TIBURON: Re-connect the battery prevent an accidental short circuit. Remove Spacer Set "A" to the back of the converted terminal and test the unit for proper operation. Mount the head unit/kit assembly to the sub- the ashtray and (2) screws exposed. Pop mounting tabs. Locate (4) Pan-Head dash using the hardware indicated in step #2 (see Fig. A). out the round plug from the radio trim bezel Screws and (4) Washers included in the kit and remove (1) screw exposed. Unclip and and retain for use in step #6. Skip to the SONATA: Re-connect the battery terminal and test the unit for proper operation. Mount the remove the trim bezel. Remove (4) screws Installation Instructions for ALL VEHICLES factory pocket to the sub-dash with (4) Phillips screws previously removed in step #1. Mount from the factory radio, slide the radio out and on Page #6. the head unit/kit assembly to the sub-dash with (4) Phillips screws previously removed in step disconnect the wiring. #1 (see Fig. B). 1 6 MITSUBISHI Precis 1986-89 HYUNDAI Excel 1990-94 1 2 12 Locate Radio Housing "A" included in the Locate Radio Housing "B" included in the kit and retain for use in step #3. Locate (4) kit and retain for use in step #3. Locate (4) Pan-Head Screws and (4) Washers Disconnect the negative battery terminal to Oval-Head Screws and (4) Plugs included Disconnect the negative battery terminal to included in the kit and retain for use in step prevent an accidental short circuit. Remove in the kit and retain for use in step #6. Skip to prevent an accidental short circuit. Remove #6. (It may be necessary to attach Spacer (4) Phillips screws from the factory radio the Installation Instructions for ALL (2) screws from the ashtray cavity. Pop out Set "B" to the front of the mounting tabs for mounting plate. Slide the radio assembly VEHICLES on Page #6. the hazard switch and remove (1) screw some later models). Skip to the Installation out and disconnect the wiring. exposed. Pop out the switch blank from the Instructions for ALL VEHICLES on Page #6. far-right position and remove (1) screw exposed. Remove the trim bezel/factory radio and disconnect the wiring. ALL VEHICLES HYUNDAI Excel 1986-89 3 1 2 Fig. A Fig. B Locate Radio Housing "B" included in the kit and retain for use in step #3. Locate (4) 2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft Disconnect the negative battery terminal to Oval-Head Screws and (4) Plugs included nuts. (see Fig. A) prevent an accidental short circuit. Remove in the kit and retain for use in step #6. Skip to (4) Phillips screws from the factory radio the Installation Instructions for ALL DIN HEAD UNITS: Cut and remove the shaft supports. Slide the DIN cage into the Radio mounting plate. Slide the radio assembly VEHICLES on Page #6. Housing and secure by bending the metal locking tabs down. Slide the aftermarket head unit out and disconnect the wiring. into the cage until secure. (see Fig. B) 5 2 HYUNDAI Scoupe 1991-95 HYUNDAI Tiburon 1997-02 12 12 Locate Radio Housing "C" included in the Disconnect the negative battery terminal to Locate Radio Housing "D". Locate the (4) kit and retain for use in step #3. Locate the prevent an accidental short circuit. Remove factory screws previously removed in step Disconnect the negative battery terminal to (4) factory screws previously removed in (4) Phillips screws securing the center #1 and retain for use in step #6. Skip to the prevent an accidental short circuit. Remove step #1 and retain for use in step #6. Skip to console. Pry out on the front edge of the Installation Instructions for ALL VEHICLES (2) screws from the bottom of the radio trim the Installation Instructions for ALL console and unclip the radio trim bezel. on Page #6. bezel. Remove the bezel and disconnect VEHICLES on Page #6. Remove (2) Phillips screws securing the the wiring. Remove (4) screws from the factory pocket and remove. Remove (4) factory radio, slide the radio out and Phillips screws securing the factory head disconnect the wiring. unit and disconnect the wiring. HYUNDAI Sonata 1995-98 MITSUBISHI Precis 1990-93 12"A" 12 Fig. A Locate Radio Housing "A" included in the Disconnect the negative battery terminal to Locate Radio Housing "D". Locate the (4) kit and retain for use in step #3. Locate (4) prevent an accidental short circuit. Unclip factory screws previously removed in step Pan-Head Screws and (4) Washers the gear shifter trim panel and remove (1) #1 and retain for use in step #6. Skip to the Disconnect the negative battery terminal to included in the kit and retain for use in step screw exposed. Unclip the dash trim bezel Installation Instructions for ALL VEHICLES prevent an accidental short circuit. Remove #6. (It may be necessary to attach Spacer and remove. Remove (4) Phillips screws on Page #6. (2) screws from the ashtray cavity. Pop out Set "B" to the front of the mounting tabs for securing the factory head unit and the hazard switch and remove (1) screw some later models). Skip to the Installation disconnect the wiring. Cut and remove tabs exposed. Pop out the switch blank from the Instructions for ALL VEHICLES on Page #6. "A" located in the top corners of the dash far-right position and remove (1) screw cavity. (see Fig. A). exposed. Remove the trim bezel/factory radio and disconnect the wiring. 3 4.