DOCSLIB.ORG

Solmat-D-17-00752R1

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Solmat-D-17-00752R1 Elsevier Editorial System(tm) for Solar Energy Materials and Solar Cells Manuscript Draft Manuscript Number: SOLMAT-D-17-00752R1 Title: Development of low-cost inorganic salt hydrate as a thermochemical energy storage material Article Type: Full Length Article Keywords: thermochemical storage material; bischofite; isothermal kinetics; dehydration reaction; salt hydrate Corresponding Author: Dr. Svetlana Ushak, Doctor in Chemistry Corresponding Author's Institution: University of Antofagasta First Author: Veronica Mamani Order of Authors: Veronica Mamani; Andrea Gutierrez; Svetlana Ushak, Doctor in Chemistry Abstract: Thermochemical storage is based on a reversible chemical reaction; energy can be stored when an endothermic chemical reaction occurs and then, energy is released when it is reversed in an exothermic reaction. According to literature and based on the energy storage density (esd), MgCl2·6H2O is a promising candidate material for thermochemical energy storage. Bischofite is an inorganic salt obtained as a by-product material from extraction processes of non-metallic minerals, from Salar de Atacama in Chile, containing approximately 95% of MgCl2·6H2O. Thus, the purpose of this study was to characterize the dehydration reaction of bischofite ore, studied as a low-cost thermochemical storage material. Thermogravimetric data for bischofite were obtained using a TGA instrument coupled to a DSC, at four different isotherms 70 °C, 80 °C, 90 °C and 100 °C. The results of conversion reaction (α-t) from the thermal dehydration experiments, demonstrated the first phase of dehydration with the loss of two water molecules. The study showed a typical sigmoid curve with a significant acceleration in the conversion at the beginning of the reaction until it reaches a maximum rate, where the curve keeps constant. The same behavior was observed for all the temperatures used. The kinetics of bischofite dehydration model was determined using the isothermal kinetics method. For this, the thermogravimetric data were fitted to the most used kinetic models (D, F, R, A) and then their respective correlation coefficients R were evaluated. The results indicated that the dehydration reaction of bischofite was described by the kinetics of chemical reaction of cylindrical particles R2. The rate of dehydration reaction and esd of bischofite are lower as compared to synthetic MgCl2·6H2O, at temperatures higher than 80 °C. However, the cost of materials to store 1 MJ of energy is three times lower for bischofite, which is an evident advantage to promote the reuse of this material left as waste by the non-metallic industry. *Highlights (for review) Bischofite main component is MgCl2·6H2O, a typical TCS material for seasonal storage Bischofite dehydration and kinetic study are presented in this work The rate of dehydration reaction of bischofite is lower compared with synthetic MgCl2·6H2O The esd for bischofite are lower compared with synthetic MgCl2·6H2O The cost to store 1 MJ of energy is three times lower for bischofite *Manuscript Click here to view linked References 1 2 3 4 5 Development of low-cost inorganic salt hydrate as a thermochemical 6 energy storage material 7 8 9 10 V. Mamani 1, A. Gutiérrez2, S. Ushak 1* 11 1 12 Department of Chemical Engineering and Mineral Processing and Center for Advanced Study of Lithium 13 and Industrial Minerals (CELiMIN). Universidad de Antofagasta, Campus Coloso, Av. Universidad de Antofagasta 02800, Antofagasta (Chile) 14 2 15 German Aerospace Center – DLR e. V., Institute of Technical Thermodynamics, Pfaffenwaldring 38, 70569 16 Stuttgart, Germany 17 18 Corresponding author: [email protected] 19 20 ABSTRACT 21 22 23 Thermochemical storage is based on a reversible chemical reaction; energy can be stored when an 24 endothermic chemical reaction occurs and then, energy is released when it is reversed in an 25 26 exothermic reaction. According to literature and based on the energy storage density (esd), 27 28 MgCl2·6H2O is a promising candidate material for thermochemical energy storage. Bischofite is an 29 inorganic salt obtained as a by-product material from extraction processes of non-metallic minerals, 30 31 from Salar de Atacama in Chile, containing approximately 95% of MgCl2·6H2O. Thus, the purpose 32 33 of this study was to characterize the dehydration reaction of bischofite ore, studied as a low-cost 34 thermochemical storage material. Thermogravimetric data for bischofite were obtained using a 35 36 TGA instrument coupled to a DSC, at four different isotherms 70 °C, 80 °C, 90 °C and 100 °C. The 37 38 results of conversion reaction (α-t) from the thermal dehydration experiments, demonstrated the 39 first phase of dehydration with the loss of two water molecules. The study showed a typical sigmoid 40 41 curve with a significant acceleration in the conversion at the beginning of the reaction until it 42 43 reaches a maximum rate, where the curve keeps constant. The same behavior was observed for all 44 the temperatures used. The kinetics of bischofite dehydration model was determined using the 45 46 isothermal kinetics method. For this, the thermogravimetric data were fitted to the most used kinetic 47 48 models (D, F, R, A) and then their respective correlation coefficients R were evaluated. The results 49 indicated that the dehydration reaction of bischofite was described by the kinetics of chemical 50 51 reaction of cylindrical particles R2. The rate of dehydration reaction and esd of bischofite are lower 52 53 as compared to synthetic MgCl2·6H2O, at temperatures higher than 80 °C. However, the cost of 54 materials to store 1 MJ of energy is three times lower for bischofite, which is an evident advantage 55 56 to promote the reuse of this material left as waste by the non-metallic industry. 57 58 Keywords: thermochemical storage material, bischofite, isothermal kinetics, dehydration reaction, 59 60 salt hydrate. 61 62 63 64 65 1 2 3 4 5 6 Nomenclature 7 esd Energy Storage Density J/cm3 8 9 ρ Density kg/ m3 10 TES Thermal Energy Storage - 11 12 α Fraction Reacted - 13 THS Thermochemical Heat Storage - 14 15 LHS Latent Heat Storage - 16 SHS Sensible Heat Storage - 17 18 PCM Phase Change Material - 19 20 TCM Thermochemical Material - 21 CHP Chemical heat pump - 22 23 DTA Differential Thermal Analysis - 24 DTG Derivative Thermogravimetric - 25 26 IR Infrared Spectroscopy - 27 SEM Scanning Electron Microscope - 28 29 STA Simultaneous Thermal Analysis - 30 EDX Energy dispersive X-ray - 31 32 TG Thermogravimetry - 33 MS Mass Spectrometer - 34 35 DSC Differential Scanning Calorimetry - 36 LM Mean Size μm 37 38 LD Mode Size μm 39 XRD X-Ray Diffraction - 40 41 t/t0.5 Time/time α =0.5 - 42 E Energy activation J/mol 43 a 44 A Frequency factor s-1 45 R Correlation coefficient - 46 47 T Temperature °C 48 t time min 49 50 b Slope - 51 52 a Intercept - 53 ΔHD Dehydration enthalpy kJ/kg 54 55 k Rate constant - 56 % wt Percentage of weight loss % 57 58 59 60 61 62 63 64 65 1 2 3 4 1. Introduction 5 6 Thermal energy storage (TES) is an available technology, where energy in the form of heat or cold 7 is stored in materials (charging process) for a specific time, to be released in the form of heat 8 9 (discharge process), which can be transformed into other forms of energy or simply used as heat, 10 11 depending on energy demand. The incorporation of TES systems increases efficiency in solar 12 energy use throughout 24 hours of the day, reduces loss of useful thermal energy and consequently 13 14 favors the reduction of greenhouse gas emissions considerably [1]. 15 16 The amount of thermal energy that can be stored and discharged depends on the characteristics of 17 the storage material and the associated temperature effects between the storage medium and the 18 19 energy source. Thermal energy can be stored by virtue of the internal energy change of a material 20 21 caused by sensible heat, latent heat, and chemical reactions [1]. Sensible heat TES systems store 22 23 energy through temperature change in the storage materials, where thermal energy is stored by 24 raising the temperature of a material [2]. Latent heat is heat absorbed or released by a material, 25 26 while changing its phase at constant temperature [3]. Latent heat is released when the phase change 27 28 material (PCM) is cooled again and solidifies. However, the main disadvantages of these two, 29 sensible and latent, heat storage forms are low energy density and considerable heat loss during 30 31 storage. These disadvantages are overcome by the heat storage type occurring by means of a 32 33 chemical reaction, also called thermochemical storage, since it keeps high energy density, which 34 becomes 5 and 10 times greater, compared to latent heat and sensible heat storage systems, 35 36 respectively. This thermochemical storage type is mainly based on obtaining heat by means of a 37 38 reversible chemical reaction (See Figure 1 [4]). In this reaction, a thermochemical energy storage 39 material (C) absorbs external heat (e.g. solar energy) through an endothermic reaction, 40 41 decomposing into A and B. Products (A and B) are separated by physical means and stored in 42 43 separate containers. When materials A and B are combined again, exothermic reverse reaction, 44 generation of C and release of stored thermal energy occur [5]. 45 46 Storage and transport times are theoretically unlimited because there is no heat loss during storage 47 48 of materials A, B and C; thus, products can be stored at room temperature. Therefore, these are 49 promising systems for long-term heat storage (as seasonal storage) [6,7]. Recent studies also show 50 51 advances in applications of thermochemical storage systems at high temperature in CSP plants [8].
Load more

Recommended publications
  • OCCURRENCE of BROMINE in CARNALLITE and SYLVITE from UTAH and NEW MEXICO* Manrr Loursp Lrnosonc
    OCCURRENCE OF BROMINE IN CARNALLITE AND SYLVITE FROM UTAH AND NEW MEXICO* Manrr Loursp LrNosonc ABSTRACT Both carnallite and sylvite from Eddy County, New Mexico, contain 0.1 per cent of bromine. The bromine content of these minerals from Grand county, utah, is three times as great. No bromine was detected in halite, polyhalite, l5ngbeinite, or anhydrite from New Mexico. Iodine was not detected in any of these minerals. on the basis of the bromine content of the sylvite from New Mexico, it is calculated that 7,000 tons of bromine were present in potash salts mined from the permian basin during the period 1931 to 1945. INrnooucrroN The Geological Survey has previously made tests for bromine and iodine in core samples of potash salts from New Mexico.r Bromine was found to be present in very small amounts. No systematic quantitative determinations were made, nor was the presenceof bromine specificalry correlated with quantitative mineral composition. Sections of potash core from four recently drilled wells and selected pure saline minerals from Eddy County, New Mexico, together with two cores from Grand County, Utah, were therefore analyzed for their bromine and iodine content. The percentage mineral composition was then correlated with the bromine content. rt was found that bromine was restricted to carnall- ite and sylvite. fodine was not detected in any of the samples analyzed. If present, its quantity must be less than .00570. Brine and sea water are the present commercial sourcesof bromine in the United States, though both Germany and U.S.S.R. have utilized potash salts as a source of bromine.
    [Show full text]
  • Seepage Chemistry Manual
    RECLAMManagAingTWateIr iOn theNWest Report DSO-05-03 Seepage Chemistry Manual Dam Safety Technology Development Program U.S. Department of the Interior Bureau of Reclamation Technical Service Center Denver, Colorado December 2005 Form Approved REPORT DOCUMENTATION PAGE OMB No. 0704-0188 The public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 2. REPORT TYPE 3. DATES COVERED (From - To) 12-2005 Technical 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER Seepage Chemistry Manual 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER Craft, Doug 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT Bureau of Reclamation, Technical Service Center, D-8290, PO Box 25007, NUMBER Denver CO 80225 DSO-05-03 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10.
    [Show full text]
  • Chlorine and Bromine Isotope Evolution Within a Fully Developed Upper Permian Natural Salt Sequence
    Published in “Geochimica et Cosmochimica Acta” volume 245, pages 316-326. DOI: https://doi.org/10.1016/j.gca.2018.11.010. Use the above information when citing this article. Chlorine and bromine isotope evolution within a fully developed Upper Permian natural salt sequence HGM Eggenkampa,*, P Louvatb, J Griffioenc,d, P Agriniera aÉquipe de Géochimie des Isotopes Stables, Institut de Physique du Globe de Paris, Sorbonne Paris Cité, UMR 7154, CNRS, 1 rue Jussieu, 75238 Paris Cedex 05, France bÉquipe de Géochimie des Enveloppes Externes, Institut de Physique du Globe de Paris, Sorbonne Paris Cité, UMR 7154, CNRS, 1 rue Jussieu, 75238 Paris Cedex 05, France cTNO Geological Survey of the Netherlands, P.O. Box 80015, Utrecht, The Netherlands dCopernicus Institute of Sustainable Development, Utrecht University, P.O. Box 80115, Utrecht, The Netherlands *Corresponding author, email [email protected] Abstract The behaviour of chlorine and bromine isotopes in evaporite deposits differs significantly. We studied the isotope variations of both elements in a fully developed natural salt sequence from Zechstein evaporite deposits (Wuchiapingian, Upper Permian) in the Northern Netherlands. We observed that the Cl isotope variations follow previously predicted characteristics, showing slightly positive δ37Cl (relative to seawater) in halite (NaCl) dominated layers (up to +0.05 ‰), decreasing to moderately negative values in carnallite (KMgCl3•6H2O) and bischofite (MgCl2•6H2O) dominated layers (down to -0.55 ‰). Bromine isotope variations, the first ever measured in marine evaporite samples, show a different characteristic. δ81Br values 1 of 27 decrease quickly in layers dominated by halite (from +0.2 to -0.5 ‰) and increase again in layers dominated by carnallite and bischofite (up to - 0.1±0.2‰).
    [Show full text]
  • Reflectance Spectral Characteristics of Minerals in the Mboukoumassi
    minerals Article Reflectance Spectral Characteristics of Minerals in the Mboukoumassi Sylvite Deposit, Kouilou Province, Congo Xian-Fu Zhao 1,2, Zong-Qi Wang 1,*, Jun-Ting Qiu 3,* and Yang Song 2 1 Ministry of Land and Resources Key Laboratory of Metallogeny and Mineral Assessment, Institute of Mineral Resources, Chinese Academy of Geological Sciences, Beijing 100037, China; [email protected] 2 School of Earth Sciences and Resources, China University of Geosciences, Beijing 100083, China; [email protected] 3 National Key Laboratory of Science and Technology on Remote Sensing Information and Image Analysis, Beijing Research Institute of Uranium Geology, Beijing 100029, China * Correspondence: [email protected] (Z.-Q.W.); [email protected] (J.-T.Q.); Tel.: +86-10-82251207 (Z.-Q.W.); +86-10-64962683 (J.-T.Q.) Academic Editor: Dimitrina Dimitrova Received: 20 March 2016; Accepted: 23 May 2016; Published: 14 June 2016 Abstract: This study presents reflectance spectra, determined with an ASD Inc. TerraSpec® spectrometer, of five types of ore and gangue minerals from the Mboukoumassi sylvite deposit, Democratic Republic of the Congo. The spectral absorption features, with peaks at 999, 1077, 1206, 1237, 1524, and 1765 nm, of the ore mineral carnallite were found to be different from those of gangue minerals. Spectral comparison among carnallite samples from different sylvite deposits suggests that, in contrast to spectral shapes, the absorption features of carnallite are highly reproducible. Heating of carnallite to 400 and 750˝C, and comparing the spectra of heated and non-heated samples, indicates that spectral absorption is related to lattice hydration or addition of hydroxyl.
    [Show full text]
  • Evaluation of Nacl and Mgcl2 Heat Exchange Fluids in a Deep Binary
    Moore and Holländer Geotherm Energy (2021) 9:8 https://doi.org/10.1186/s40517-021-00190-3 RESEARCH Open Access Evaluation of NaCl and MgCl2 heat exchange fuids in a deep binary geothermal system in a sedimentary halite formation Kayla R. Moore* and Hartmut M. Holländer *Correspondence: [email protected] Abstract Department of Civil Halite formations are attractive geothermal reservoirs due to their high heat conductiv- Engineering, University of Manitoba, Winnipeg, MB ity, resulting in higher temperatures than other formations at similar depths. However, R3T 5V6, USA halite formations are highly reactive with undersaturated water. An understanding of the geochemical reactions that occur within halite-saturated formation waters can inform decision making regarding well construction, prevention of well clogging, for- mation dissolution, and thermal short-circuiting. Batch reaction and numerical 3-D fow and equilibrium reactive transport modeling were used to characterize the produced NaCl-brine in a well targeting a halite-saturated formation. The potential for inhibition of precipitation and dissolution using an MgCl2-brine and NaCl ­MgCl2-brine were also investigated. Within the injection well, heating of an NaCl-brine+ from 70 to 120 °C caused the solubility of halite to decrease, resulting in the potential dissolution of 1 0.479 mol kg− halite at the formation. Conversely, cooling from 120 to 100 °C in the 1 production well resulted in potential precipitation of 0.196 mol kg− halite. Concur- rent precipitation of anhydrite is also expected. Introduction of MgCl2 into the heat exchange brine, which has a common Cl− ion, resulted in a decreased potential for 1 dissolution by 0.290 mol kg− halite within the formation, as well as decreased precipi- tation within the production well, compared to the NaCl-brine.
    [Show full text]
  • A Specific Gravity Index for Minerats
    A SPECIFICGRAVITY INDEX FOR MINERATS c. A. MURSKyI ern R. M. THOMPSON, Un'fuersityof Bri.ti,sh Col,umb,in,Voncouver, Canad,a This work was undertaken in order to provide a practical, and as far as possible,a complete list of specific gravities of minerals. An accurate speciflc cravity determination can usually be made quickly and this information when combined with other physical properties commonly leads to rapid mineral identification. Early complete but now outdated specific gravity lists are those of Miers given in his mineralogy textbook (1902),and Spencer(M,i,n. Mag.,2!, pp. 382-865,I}ZZ). A more recent list by Hurlbut (Dana's Manuatr of M,i,neral,ogy,LgE2) is incomplete and others are limited to rock forming minerals,Trdger (Tabel,l,enntr-optischen Best'i,mmungd,er geste,i,nsb.ildend,en M,ineral,e, 1952) and Morey (Encycto- ped,iaof Cherni,cal,Technol,ogy, Vol. 12, 19b4). In his mineral identification tables, smith (rd,entifi,cati,onand. qual,itatioe cherai,cal,anal,ys'i,s of mineral,s,second edition, New york, 19bB) groups minerals on the basis of specificgravity but in each of the twelve groups the minerals are listed in order of decreasinghardness. The present work should not be regarded as an index of all known minerals as the specificgravities of many minerals are unknown or known only approximately and are omitted from the current list. The list, in order of increasing specific gravity, includes all minerals without regard to other physical properties or to chemical composition. The designation I or II after the name indicates that the mineral falls in the classesof minerals describedin Dana Systemof M'ineralogyEdition 7, volume I (Native elements, sulphides, oxides, etc.) or II (Halides, carbonates, etc.) (L944 and 1951).
    [Show full text]
  • Thermophysical Characterization of a By-Product from the Non-Metallic Industry As Inorganic PCM
    Thermophysical characterization of a by-product from the non-metallic industry as inorganic PCM Svetlana Ushak1,2,*, Andrea Gutierrez1, Hector Galleguillos1,2, Angel G. Fernandez1,2, Luisa F. Cabeza3, Mario Grágeda1,2 1 Department of Chemical Engineering and Mineral Processing and Center for Advanced Study of Lithium and Industrial Minerals (CELiMIN), Universidad de Antofagasta, Campus Coloso, Av. Universidad de Antofagasta 02800, Antofagasta, Chile. *[email protected] 2 Solar Energy Research Center (SERC-Chile), Av Tupper 2007, Piso 4, Santiago, Chile 3 GREA Innovació Concurrent, Universitat de Lleida, Edifici CREA, Pere de Cabrera s/n, 25001, Lleida, Spain Abstract Physical characterization and thermal properties of bischofite, a by-product from the non- metallic industry, were determined and compared with those to MgCl2·6H2O with the idea of using it as phase change material in thermal energy storage applications. The melting point and heat of fusion were measured in the temperature range from 30°C to 150°C, where Tfus and ΔHfus were 100°C and 115 kJ/kg for bischofite, and 114.5°C and 135 kJ/kg for MgCl2·6H2O. The solid heat capacity was determined from 25°C to 60°C, being 2.1 kJ/(kg·K) at 60°C for both samples. The measurements of the liquid heat capacity of bischofite were done from 105°C to 113°C and the Cp showed linear increase from 5.61 kJ/(kg·K) to 9.01 kJ/(kg·K). The thermal stability test (30 heating/cooling cycles) of bischofite and MgCl2·6H2O shows subcooling of about 37K and 29K, respectively.
    [Show full text]
  • THE STABILITY of GYPSUM and ANHYDRITE in the GEOLOGIC ENVIRONMENT by Leonard S
    THE STABILITY OF GYPSUM AND ANHYDRITE IN THE GEOLOGIC ENVIRONMENT by LEONARD STEVEN ROLNICK A.B., THE JOHNS HOPKINS UNIVERSITY (1950) SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF DOCTOR OF PHILOSOPHY at the MASSACHUSETTS INSTITUTE OF TECHNOLOGY September, 1954 Signature of Author.......... .................... ...... *0 Department of Geology and G o s September 10, 1954 Certified by....e. .... .. e....sor Thesis Supervisor Accepted by......, .......... 0 e Chairman, Departmental Committee on raduate Students ~~~~1 THE STABILITY OF GYPSUM AND ANHYDRITE IN THE GEOLOGIC ENVIRONMENT by Leonard S. Rolnick Submitted to the Department of Geology and Geophysics on September 10, 1954, in partial fulfillment of the require- ments for the degree of Doctor of Philosophy In the CaSO-- H2 0 system, gypsum and anhydrite are the only two minerals that are sufficiently stable to exist as geologic deposits. From thermodynamic data and solubility measurements the transition temperature has previously been found to be about 4000, above which anhydrite is the stable phase and below which gypsum is the stable phase, when they are in contact with an aqueous solution at atmospheric pressure. By a process of solution and recrystallization, one can be converted to the other, after the surrounding liquid is saturated with calcium sulphate. Experimental work has been done in a study of the effects of pressure on this transition point, and the results corroborate and extend the theoretical calculations of MacDonald, which are based on thermodynamic data. This experimentally determined information was used in explaining some of the gypsum-anhydrite sequences found in geologic deposits. The experiments were conducted using high pressure bombs which contained samples of pure gypsum or anhydrite in a saturated calcium sulphate solution.
    [Show full text]
  • Properties of Salt Compounds
    Properties of salt compounds Exposé Mona-Maria Druske 1. Background Materials used for chemical heat storage applications [1, 2] need to possess certain key properties. The most important of those properties are a high heat storage density and an also high cycle stability, which will allow for a compact storage system that can run for several years without requiring an exchange of the storage material within. Further it is aimed to find inexpensive and non-hazardous/-corrosive materials. As salts are cheap and easily available, as well as relatively safe materials to work with and most of them can incorporate water (or other polar reaction partners, such as ammonia or alcohols) into their crystal structure in a reversible chemical reaction, they are of prime interest in the research for suitable materials. While most basic salts possess the latter properties, and some show promising heat storage densities, they usually need relatively high temperatures for dehydration of T>100°C. This is a serious limitation, since many thermal processes are based on water as heat transfer fluid and therefore the boiling point of water is limiting the temperature range. The other main problem is the low cycle stability of the materials. Hydrated salts easily lump together or melt during dehydration, as they have low melting points compared to their anhydrates. Once molten, they rather solidify as an amorphous mass upon cooling than recrystallizing which will hinder the rehydration process. 2. Materials Chlorides, Sulfates and Bromides of Na, K, Li, Sr, Ca, Mg, Zn, Fe2+, Fe3+ or Al are storage material candidates. However Fe2+ and Fe3+ can cause the development of unwanted byproducts and most Li containing salts are too expensive to be efficient.
    [Show full text]
  • The Mineral Industries of Countries of the Baltic (Estonia, Latvia, Lithuania
    2008 Minerals Yearbook COUNTRIES OF THE BALTIC REGION (ESTONIA, LATVIA, LITHUANIA), CAUCASUS REGION (ARMENIA, AZERBAIJAN, GEORGIA), CENTRAL ASIA REGION (KAZAKHSTAN, KYRGYZSTAN, TAJIKISTAN, TURMKENISTAN, UZBEKISTAN), AND EURASIA REGION (BELARUS, MOLDOVA, RUSSIA) U.S. Department of the Interior December 2010 U.S. Geological Survey THE MINERAL INDUS T RIES OF COUN T RIES OF T HE BAL T I C REGION (ES T ONIA , LA T VIA , LI T HUANIA ), CAU C ASUS REGION (AR M ENIA , AZER B AIJAN , GEORGIA ), CEN T RAL ASIA REGION (KAZA K HS T AN , KYRGYZS T AN , TAJI K IS T AN , TUR km ENIS T AN , UZ B E K IS T AN ), AND EURASIA REGION (BELARUS , MOLDOVA , RUSSIA ) By Richard M. Levine and Glenn J. Wallace The countries that are covered in this report are grouped also can include a number of the above cited minerals, as well into the following four geographic regions: the Baltic region as gallium, hafnium, tellurium, and selenium, are produced as (Estonia, Latvia, Lithuania), the Caucasus region (Armenia, byproducts from the production of bauxite, copper, lead and Azerbaijan, Georgia), the Central Asia region (Kazakhstan, zinc, and uranium ores. A number of these minerals have been Kyrgyzstan, Tajikistan, Turkmenistan, Uzbekistan), and the designated as critical and strategic by various Governments. Eurasia region (Belarus, Moldova, Russia). These countries Other elements could possibly be added to this list now, and all had been republics of the Soviet Union prior to 1992, still others will emerge as technological developments take although the United States Government never recognized place. This report, however, is only an initial effort to assess the incorporation of Estonia, Latvia, and Lithuania into the production of such commodities in this part of the world.
    [Show full text]
  • Martian Brines
    Icarus 212 (2011) 123–130 Contents lists available at ScienceDirect Icarus journal homepage: www.elsevier.com/locate/icarus Properties of cryobrines on Mars ⇑ D. Möhlmann a, , K. Thomsen b a DLR Institut für Planetenforschung, Berlin, Germany b CERE, Department of Chemical and Biochemical Engineering, Technical University of Denmark, Lyngby, Denmark article info abstract Article history: Brines, i.e. aqueous salty solutions, increasingly play a role in a better understanding of physics and Received 31 May 2010 chemistry (and eventually also putative biology) of the upper surface of Mars. Results of physico-chem- Revised 12 November 2010 ical modeling and experimentally determined data to characterize properties of cryobrines of potential Accepted 17 November 2010 interest with respect to Mars are described. Eutectic diagrams, the related numerical eutectic values of Available online 27 November 2010 composition and temperature, the water activity of Mars-relevant brines of sulfates, chlorides, perchlo- rides and carbonates, including related deliquescence relative humidity, are parameters and properties, Keywords: which are described here in some detail. The results characterize conditions for liquid low-temperature Mars brines (‘‘cryobrines’’) to evolve and to exist, at least temporarily, on present Mars. Mars, surface Ó 2010 Elsevier Inc. All rights reserved. 1. Introduction 2007; Catling, 2009). Liquid water has after the Noachian increas- ingly been disappeared from the surface of Mars. Surface imaging The discussion of a possible presence of brines on Mars dates and geomorphology have revealed indications for increasingly spo- back more than 30 years (Brass, 1980; Clark and Van Hart, 1981), radic but nevertheless massive (catastrophic) temporary surface and it has recently culminated with in situ discoveries in course water floods and flows (Carr and Head, 2009; Hauber et al., of NASA’s Phoenix mission (Hecht et al., 2009; Renno et al., 2009).
    [Show full text]
  • Critical Raw Materials Profiles
    Ref. Ares(2015)1819595 - 29/04/2015 REPORT ON CRITICAL RAW MATERIALS FOR THE EU CRITICAL RAW MATERIALS PROFILES Contents REPORT ON CRITICAL RAW MATERIALS FOR THE EU 1 1 Critical Raw Materials 1 1.1 Antimony (Stibium) 1 1.2 Beryllium 11 1.3 Borates 17 1.4 Chromium 26 1.5 Cobalt (Cobaltum) 34 1.6 Coking coal 42 1.7 Fluorspar (Fluorite) 50 1.8 Gallium 57 1.9 Germanium 67 1.10 Indium 77 1.11 Magnesite 86 1.12 Magnesium 92 1.13 Natural graphite 99 1.14 Niobium 109 1.15 Phosphate rock 116 1.16 Platinum group metals* 123 1.17 Rare earth elements (Light and Heavy)* 146 1.18 Silicon metal (Silicium) 184 1.19 Tungsten (Wolframium) 193 *Separate profiles for the metals in these groups are provided with the group profile. See separate documents for main report and non-critical raw material profiles. For DG Enterprise and Industry Glossary APT ammonium paratungstate BGR German Federal Institute for Geosciences and Natural Resources BGS British Geological Survey BRGM Bureau de Recherches Géologiques et Minières CAGR compound annual growth rate CCM Caustic calcined magnesite CIGS Copper indium gallium (di)selenide CIS Copper indium (di)selenide DBM Dead burned magnesite DRC Democratic Republic of the Congo EEA European Environment Agency ENRC Eurasian Natural Resources Corporation EOL-RR end-of-life recycling rate FAO Food and Agriculture Organization of the United Nations FCCs fluid cracking catalysts FM Fused Magnesite HREEs Heavy Rare Earth Elements IC integrated circuit IR infrared radiation ITO Indium Titanium Oxide LCD Liquid-Crystal Display LED
    [Show full text]