DOCSLIB.ORG

Decoupled Pulley Fax +49 6201 25964-11 Fax +39 0121 369299

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Decoupled Pulley Fax +49 6201 25964-11 Fax +39 0121 369299 The typical crankshaft vibrations are compensated by employing high quality decoupled belt pulleys. This minimizes the transmission of vibrations to other vehicle components and the associated effects on the entire vehicle. So you can enjoy undisturbed ride comfort. CORTECO GmbH CORTECO S.r.l.u. SEALING VIBRATION CONTROL CABIN AIR FILTER Badener Straße 4 Corso Torino 420/D 69493 Hirschberg 10064 Pinerolo (TO) Germanny Italy Corteco original quality Tel. +49 6201 25964-0 Tel. +39 0121 369269 Decoupled PULLEY Fax +49 6201 25964-11 Fax +39 0121 369299 CORTECO S.A.S. CORTECO Ltd. Z.A. La Couture Unit 6, Wycliffe Industrial 87140 Nantiat Park Complex inner workings: France Lutterworth The decoupled belt pulley Tel. +33 5 55536800 Leicestershire is joined to the torsional Fax +33 5 55536888 LE17 4HG vibration damper by a United Kingdom highly elastic elastomer Tel. +44 1455 550000 part, thereby offering opti- www.corteco.com Fax +44 1455 550066 mum damping properties. 19036674 SIG-08/2012 THE belt DRIVE MOVES A EXPENSIVE economic Satisfied customers NUMBER OF THINGS MEASURES ARE GOOD customers No matter whether a drive belt is too loud or ancillary units are damaged by vibration – belt drive decoupling deficiencies are always associated with dissatisfaction. Anyone not using original parts for a decoupled belt pul- ley is making a false saving. Cheap counterfeit products generally lead to complaints after a short running time and loss of customer confidence. On the other hand, ori- ginal parts from CORTECO still work reliably, often after 100,000 kilometers. Transmission of crankshaft vibrations to ancillary units can produce an increased noise level, severe wear of adjoi- Original: after 100,000 km in the vehicle The decoupled belt pulley should be checked after about ning components and undesirable vehicle vibration. The 90,000 km and replaced together with the tensioner decoupled belt pulley is specially designed to meet the belt. Rely on OEM quality, as only satisfied customers requirements of modern, high performance diesel engines, are good customers. which develop a considerably higher vibration response than petrol engines. Your benefits from OEM quality: CORTECO offers additional Kits: Reased service life of the belt and of 32 bolt kits the belt tensioner 23 pulley kits including bolts and washers Quieter running of the belt drive Complete seal sets for clutch replacement and Less stress on adjoining components timing belt exchange Copy: complaint after short running time Safety from OEM quality Satisfied and loyal customers Talk to our customer service. THE belt DRIVE MOVES A EXPENSIVE economic Satisfied customers NUMBER OF THINGS MEASURES ARE GOOD customers No matter whether a drive belt is too loud or ancillary units are damaged by vibration – belt drive decoupling deficiencies are always associated with dissatisfaction. Anyone not using original parts for a decoupled belt pul- ley is making a false saving. Cheap counterfeit products generally lead to complaints after a short running time and loss of customer confidence. On the other hand, ori- ginal parts from CORTECO still work reliably, often after 100,000 kilometers. Transmission of crankshaft vibrations to ancillary units can produce an increased noise level, severe wear of adjoi- Original: after 100,000 km in the vehicle The decoupled belt pulley should be checked after about ning components and undesirable vehicle vibration. The 90,000 km and replaced together with the tensioner decoupled belt pulley is specially designed to meet the belt. Rely on OEM quality, as only satisfied customers requirements of modern, high performance diesel engines, are good customers. which develop a considerably higher vibration response than petrol engines. Your benefits from OEM quality: CORTECO offers additional Kits: Reased service life of the belt and of 32 bolt kits the belt tensioner 23 pulley kits including bolts and washers Quieter running of the belt drive Complete seal sets for clutch replacement and Less stress on adjoining components timing belt exchange Copy: complaint after short running time Safety from OEM quality Satisfied and loyal customers Talk to our customer service. THE belt DRIVE MOVES A EXPENSIVE economic Satisfied customers NUMBER OF THINGS MEASURES ARE GOOD customers No matter whether a drive belt is too loud or ancillary units are damaged by vibration – belt drive decoupling deficiencies are always associated with dissatisfaction. Anyone not using original parts for a decoupled belt pul- ley is making a false saving. Cheap counterfeit products generally lead to complaints after a short running time and loss of customer confidence. On the other hand, ori- ginal parts from CORTECO still work reliably, often after 100,000 kilometers. Transmission of crankshaft vibrations to ancillary units can produce an increased noise level, severe wear of adjoi- Original: after 100,000 km in the vehicle The decoupled belt pulley should be checked after about ning components and undesirable vehicle vibration. The 90,000 km and replaced together with the tensioner decoupled belt pulley is specially designed to meet the belt. Rely on OEM quality, as only satisfied customers requirements of modern, high performance diesel engines, are good customers. which develop a considerably higher vibration response than petrol engines. Your benefits from OEM quality: CORTECO offers additional Kits: Reased service life of the belt and of 32 bolt kits the belt tensioner 23 pulley kits including bolts and washers Quieter running of the belt drive Complete seal sets for clutch replacement and Less stress on adjoining components timing belt exchange Copy: complaint after short running time Safety from OEM quality Satisfied and loyal customers Talk to our customer service. The typical crankshaft vibrations are compensated by employing high quality decoupled belt pulleys. This minimizes the transmission of vibrations to other vehicle components and the associated effects on the entire vehicle. So you can enjoy undisturbed ride comfort. CORTECO GmbH CORTECO S.r.l.u. SEALING VIBRATION CONTROL CABIN AIR FILTER Badener Straße 4 Corso Torino 420/D 69493 Hirschberg 10064 Pinerolo (TO) Germanny Italy Corteco original quality Tel. +49 6201 25964-0 Tel. +39 0121 369269 Decoupled PULLEY Fax +49 6201 25964-11 Fax +39 0121 369299 CORTECO S.A.S. CORTECO Ltd. Z.A. La Couture Unit 6, Wycliffe Industrial 87140 Nantiat Park Complex inner workings: France Lutterworth The decoupled belt pulley Tel. +33 5 55536800 Leicestershire is joined to the torsional Fax +33 5 55536888 LE17 4HG vibration damper by a United Kingdom highly elastic elastomer Tel. +44 1455 550000 part, thereby offering opti- www.corteco.com Fax +44 1455 550066 mum damping properties. 19036674 SIG-08/2012 The typical crankshaft vibrations are compensated by employing high quality decoupled belt pulleys. This minimizes the transmission of vibrations to other vehicle components and the associated effects on the entire vehicle. So you can enjoy undisturbed ride comfort. CORTECO GmbH CORTECO S.r.l.u. SEALING VIBRATION CONTROL CABIN AIR FILTER Badener Straße 4 Corso Torino 420/D 69493 Hirschberg 10064 Pinerolo (TO) Germanny Italy Corteco original quality Tel. +49 6201 25964-0 Tel. +39 0121 369269 Decoupled PULLEY Fax +49 6201 25964-11 Fax +39 0121 369299 CORTECO S.A.S. CORTECO Ltd. Z.A. La Couture Unit 6, Wycliffe Industrial 87140 Nantiat Park Complex inner workings: France Lutterworth The decoupled belt pulley Tel. +33 5 55536800 Leicestershire is joined to the torsional Fax +33 5 55536888 LE17 4HG vibration damper by a United Kingdom highly elastic elastomer Tel. +44 1455 550000 part, thereby offering opti- www.corteco.com Fax +44 1455 550066 mum damping properties. 19036674 SIG-08/2012.
Load more

Recommended publications
  • Engine Components and Filters: Damage Profiles, Probable Causes and Prevention
    ENGINE COMPONENTS AND FILTERS: DAMAGE PROFILES, PROBABLE CAUSES AND PREVENTION Technical Information AFTERMARKET Contents 1 Introduction 5 2 General topics 6 2.1 Engine wear caused by contamination 6 2.2 Fuel flooding 8 2.3 Hydraulic lock 10 2.4 Increased oil consumption 12 3 Top of the piston and piston ring belt 14 3.1 Hole burned through the top of the piston in gasoline and diesel engines 14 3.2 Melting at the top of the piston and the top land of a gasoline engine 16 3.3 Melting at the top of the piston and the top land of a diesel engine 18 3.4 Broken piston ring lands 20 3.5 Valve impacts at the top of the piston and piston hammering at the cylinder head 22 3.6 Cracks in the top of the piston 24 4 Piston skirt 26 4.1 Piston seizure on the thrust and opposite side (piston skirt area only) 26 4.2 Piston seizure on one side of the piston skirt 27 4.3 Diagonal piston seizure next to the pin bore 28 4.4 Asymmetrical wear pattern on the piston skirt 30 4.5 Piston seizure in the lower piston skirt area only 31 4.6 Heavy wear at the piston skirt with a rough, matte surface 32 4.7 Wear marks on one side of the piston skirt 33 5 Support – piston pin bushing 34 5.1 Seizure in the pin bore 34 5.2 Cratered piston wall in the pin boss area 35 6 Piston rings 36 6.1 Piston rings with burn marks and seizure marks on the 36 piston skirt 6.2 Damage to the ring belt due to fractured piston rings 37 6.3 Heavy wear of the piston ring grooves and piston rings 38 6.4 Heavy radial wear of the piston rings 39 7 Cylinder liners 40 7.1 Pitting on the outer
    [Show full text]
  • Timing Belt Interference Caution Note: Camshaft
    Carmax 6067 170 Turnpike Rd Westborough, MA 01581 YMMS: 1991 Chevrolet Lumina Z34 Sep 3, 2020 Engine: 3.4L Eng License: VIN: Odometer: TIMING BELT INTERFERENCE CAUTION NOTE: CAMSHAFT DRIVE BELTS OR TIMING BELTS - The condition of camshaft drive belts should always be checked on vehicles which have more than 50,000 miles. Although some manufacturers do not recommend replacement at a specified mileage, others require it at 60,000-100,000 miles. A camshaft drive belt failure may cause extensive damage to internal engine components on most engines, although some designs do not allow piston-to-valve contact. These designs are often called "Free Wheeling". Many manufacturers changed their maintenance and warranty schedules in the mid-1980's to reflect timing belt inspection and/or replacement at 50,000- 60,000 miles. Most service interval schedules shown in this section reflect these changes. Belts or components should be inspected and replaced if any of the following conditions exist: Crack Or Tears In Belt Surface Missing, Damaged, Cracked Or Rounded Teeth Oil Contamination Damaged Or Faulty Tensioners Incorrect Tension Adjustment REMOVAL & INSTALLATION Tip: Timing belt CAUTION: For 1996-97 models, this application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: The camshaft timing procedure has been updated by TSB bulletin No. 47-61-34, dated December, 1994. REMOVAL Tip: timing 3.4 x motor 1. Disconnect negative battery cable. Remove air cleaner and duct assembly. Drain engine coolant. 2. Remove accelerator and cruise control cables from throttle body.
    [Show full text]
  • Belt Drive Systems: Potential for CO2 Reductions and How to Achieve Them
    19 Belt drive 19 Belt drive Belt drive 19 Belt drive systems Potenti al for CO2 reducti ons and how to achieve them Hermann Sti ef Rainer Pfl ug Timo Schmidt Christi an Fechler 19 264 Schaeffl er SYMPOSIUM 2010 Schaeffl er SYMPOSIUM 2010 265 19 Belt drive Belt drive 19 If required, double-row Introducti on Tension pulleys and angular contact ball Single and double eccentric tensioners bearings (Figure 3) are Schaeffl er has volume produced components for idler pulleys used that also have an belt drive systems since 1977. For the past 15 years, opti mized grease sup- Schaeffl er has worked on the development of com- One use of INA idler pulleys is to reduce noise in ply volume. These plete belt drive systems in ti ming drives (Figure 1) criti cal belt spans, to prevent collision problems bearings are equipped as well as in accessory drives (Figure 2). with the surrounding structure, to guide the belt with high-temperature or to increase the angle of belt wrap on neighbor- rolling bearing greases ing pulleys. These pulleys have the same rati ng and appropriate seals. life and noise development requirements as belt Standard catalog bear- tensioning systems. For this applicati on, high-pre- ings are not as suitable Pulleys Variable camsha ming cision single-row ball bearings with an enlarged for this applicati on. grease supply volume have proven suffi cient. The tension pulleys in- stalled consist of single or double-row ball bearings specially de- veloped, opti mized and manufactured by INA for use in belt drive ap- Idler pulleys plicati ons.
    [Show full text]
  • C6 Corvette Supercharger Kit Instructions ECS SC 600 Instructions (C6)
    C6 Corvette Supercharger Kit Instructions ECS SC 600 Instructions (C6) These instructions are meant to serve as a guide to the installation of the ECS SC600 Supercharging kit. Please be sure to use all safety equipment including gloves, and eye protection. Please use proper techniques to capture and dispose of, or reuse factory fluids. Utilization of the proper tools will make the install smoother and faster. If you are having ECS provide you with a start up tune, your first step should be to remove your PCM, and ship immediately so that you can have it back ready for start up. Our shipping address is 562 Rt. 539, Cream Ridge, NJ, 08514. Installation should take between 1012 andto 15 20 hours hours for a qualified mechanic. Do not rush the install. If need technical support please call the shop at 609-752-0321. ECS SC600 Kit Installation: • Remove fuel Rail covers, and disconnect battery terminals with 10 MM wrench. • Remove cap from coolant reservoir and proceed to drain coolant by turning radiator drain cock one ¼ turn to the left. • Remove stock serpentine beltbet by placing 15mm wrench on tensioner bolt and press towards intake and pulling bet forward off tensioner • Remove stock tensioner by removing the 2 15mm bolts with socket. Save bolts for later use. • Remove hard plastic vacuum line from passenger side valve cover (Fig.1) 1 • Remove 15 mm bolt and bracket holding Evap solenoid to passenger side head and discard. Evap solenoid stays in place. (Fig.2) • DisconnectOn the drivers MAF side and of thenthe car, remove remove stock alternator air bridge wiring and filterharness assembly from top from of alternator car by loosening and positive clamps alternator and pulling wire forwardby removing and up 13mm off throttle retaining body.
    [Show full text]
  • Diesel Engine Starting Systems Are As Follows: a Diesel Engine Needs to Rotate Between 150 and 250 Rpm
    chapter 7 DIESEL ENGINE STARTING SYSTEMS LEARNING OBJECTIVES KEY TERMS After reading this chapter, the student should Armature 220 Hold in 240 be able to: Field coil 220 Starter interlock 234 1. Identify all main components of a diesel engine Brushes 220 Starter relay 225 starting system Commutator 223 Disconnect switch 237 2. Describe the similarities and differences Pull in 240 between air, hydraulic, and electric starting systems 3. Identify all main components of an electric starter motor assembly 4. Describe how electrical current flows through an electric starter motor 5. Explain the purpose of starting systems interlocks 6. Identify the main components of a pneumatic starting system 7. Identify the main components of a hydraulic starting system 8. Describe a step-by-step diagnostic procedure for a slow cranking problem 9. Describe a step-by-step diagnostic procedure for a no crank problem 10. Explain how to test for excessive voltage drop in a starter circuit 216 M07_HEAR3623_01_SE_C07.indd 216 07/01/15 8:26 PM INTRODUCTION able to get the job done. Many large diesel engines will use a 24V starting system for even greater cranking power. ● SEE FIGURE 7–2 for a typical arrangement of a heavy-duty electric SAFETY FIRST Some specific safety concerns related to starter on a diesel engine. diesel engine starting systems are as follows: A diesel engine needs to rotate between 150 and 250 rpm ■ Battery explosion risk to start. The purpose of the starting system is to provide the torque needed to achieve the necessary minimum cranking ■ Burns from high current flow through battery cables speed.
    [Show full text]
  • 3.4L (DOHC) Engine Mechanical Specifications
    60DegreeV6.com 3.4L (DOHC) Engine Mechanical Specifications Millimeters Inches Application General Data Engine Type -- 60° V-6 Displacement -- 240 Cu In Liter (VIN) -- 3.4 (X) RPO -- LQ1 Bore 92 3.622 Stroke 84 3.307 Deck Height 224 8.818 Compression Ratio -- 9.50:1 Firing Order -- 1-2-3-4-5-6 Oil Pressure @ Operating 103 kPa @ 1100 RPM 15 psi min @ 1100 RPM Temperature Cylinder Bore Diameter 92.020-92.038 3.6228-3.6235 Out Of Round Maximum 0.010 0.0004 Taper -- Thrust Side Maximum 0.013 0.00051 Center Distance 111.76 4.4 Piston Diameter-gauged at skirt 91.985-92.000 3.6215-3.6220 10.44 mm (0.413 in) below centerline of piston pin bore Clearance 0.020-0.052 0.0008-0.0020 Pin Bore 23.003-23.010 0.9056-0.9059 Piston Ring Compression Groove 0.033-0.079 0.0013-0.0031 Clearance 1st and 2nd Gap (at gauge diameter) 1st 0.20-0.45 0.008-0.018 1 60DegreeV6.com Gap (at gauge diameter) 2nd 0.56-0.81 0.022-0.032 Oil Groove Clearance 0.028-0.206 0.0011-0.0081 Gap (segment at gauge 0.25-0.76 0.0098-0.0299 diameter) Tension 1st 27.6 N 6.2 lbs Tension 2nd 19.8 N 4.5 lbs Tension Oil 31.2 N 7.0 lbs Piston Pin Diameter 22.9915-22.9964 0.9052-0.9054 Clearance 0.0066-0.0185 0.00026-0.00073 Fit In Rod 0.0165-0.0464 0.0006-0.0018 Crankshaft Main Journal Diameter-All 67.239-67.257 2.6472-2.6479 Taper-Maximum 0.005 0.0002 Out Of Round-Maximum 0.005 0.0002 Cylinder Block Main Bearing 72.155-72.168 2.8407-2.8412 Bore Diameter Crankshaft Main Bearing Inner 67.289-67.316 2.6492-2.6502 Diameter Main Bearing Clearance 0.019-0.064 0.0008-0.0025 Main Thrust Bearing Clearance
    [Show full text]
  • Electric Boosting and Energy Recovery Systems for Engine Downsizing
    energies Review Electric Boosting and Energy Recovery Systems for Engine Downsizing Mamdouh Alshammari 1,2, Fuhaid Alshammari 2 and Apostolos Pesyridis 1,* 1 Centre of Advanced Powertrain and Fuels (CAPF), Department of Mechanical, Aerospace and Civil Engineering, Brunel University London, Middlesex UB8 3PH, UK; [email protected] 2 Department of Mechanical Engineering, University of Hai’l, Hail 55476, Saudi Arabia; [email protected] * Correspondence: [email protected] Received: 31 October 2019; Accepted: 4 December 2019; Published: 6 December 2019 Abstract: Due to the increasing demand for better fuel economy and increasingly stringent emissions regulations, engine manufacturers have paid attention towards engine downsizing as the most suitable technology to meet these requirements. This study sheds light on the technology currently available or under development that enables engine downsizing in passenger cars. Pros and cons, and any recently published literature of these systems, will be considered. The study clearly shows that no certain boosting method is superior. Selection of the best boosting method depends largely on the application and complexity of the system. Keywords: engine downsizing; electrically assisted turbocharger; electric supercharger; e-turbo; waste heat recovery; turbocharging; supercharging; turbocompounding; organic Rankine cycle 1. Introduction Although internal combustion engines are getting more efficient nowadays, still the major part of fuel energy is transformed into wasted heat. In terms of harmful exhaust emissions, the transportation sector is responsible for the one-third of CO2 emissions worldwide and approximately 15% of the overall greenhouse gas emissions [1]. Moreover, owing to the limited amount of fossil fuels, prices fluctuate significantly, with consistent general rising trends, resulting in economic issues in non-oil-producing countries.
    [Show full text]
  • Comet Industrial Products
    COMET INDUSTRIAL PRODUCTS For over 60 years, Comet has been offering high performance solutions for OEM and aftermarket applications with a wide variety of centrifugal clutches, torque converters and belts for industrial products. cometclutches.com CATALOG CONTENTS Torque Converters ........................................................................4-8 Centri-Dyne Industrial Clutches ....................................................... 8 Fixed Ratio Industrial Clutches ..................................................10-11 350 Series Auto Centrifugal Clutches ........................................12-13 Clutch Lube ...................................................................................14 Belts .............................................................................................14 Brake Drum and Hub ....................................................................15 APPLICATIONS INCLUDE: Concrete Trowels Pumps Plate Compactors Material Handling Personnel Carriers ATVs, UTVs and Go-Karts Compactors Brush Cutters Compressors Bandsaws Chippers Double T-Stem Cleaners 2 cometclutches.com WHO WE ARE Founded by the Hoff Brothers in 1949, Comet has over sixty years of experience manufacturing high performance solutions for OEM and aftermarket applications with a wide variety of centrifugal and industrial clutches, torque converters, belts, disc brakes, and other components for industrial and commercial applications. Certified Parts Corporation based in Janesville, Wisconsin, acquired Hoffco/Comet December 17, 2009.
    [Show full text]
  • Diesel Engine Setting / Locking Tool Kit Chrysler 2.5Crd Engines Model No: Vs4945 Thank You for Purchasing a Sealey Product
    Instructions for: DIESEL ENGINE SETTING / LOCKING TOOL KIT CHRYSLER 2.5CRD ENGINES Model No: VS4945 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. 1. SAFETY INSTRUCTIONS 2. INTRODUCTION & APPLICATIONS WARNING! Ensure Health and Safety, local authority and general Setting and locking kit for 2.5 VM engine found in Chrysler and LDV workshop practice regulations are adhered to when using tools. vehicles. This engine has variants both with and without balancer shafts DO NOT use tools if damaged. and this kit covers both applications. The kit includes flywheel, camshaft Maintain tools in good and clean condition for best and safest and balancer locking pins plus a tensioner adjustment tool. performance. Ensure that a vehicle which has been jacked up is adequately CHRYSLER 2.5CRD Diesel engines in supported with axle stands. CHRYSLER Wear approved eye protection. A full range of personal safety Voyager Grand Voyager equipment is available from your Sealey dealer. LDV Wear suitable clothing to avoid snagging. Do not wear jewellery and Maxus tie back long hair. Engine codes: Account for all tools, locking bolts, pins and parts being used and do R2516C / R2516L engines not leave them in or near the engine.
    [Show full text]
  • Are the Days of the Starter Motor Over? By: Robert Gell, Gelcoservices Pty
    AAE&AC News Article – for Pub. July/Aug 2014 Are The Days of The Starter Motor Over? By: Robert Gell, GELCOservices Pty. Ltd. As the motor vehicle industry changes to adopt new drive systems technology it appears – at least for Hybrid drive systems – that the days of a Starter motor and flywheel ring gear may be numbered! Ultracapacitors are now beginning to be applied in low-end hybrid electric vehicles for support for primarily the Idle Stop Start (ISS) feature. In reality, an ISS system is not a true hybrid electric vehicle, rather a micro-hybrid, since it applies no electric torque to the vehicle drive wheels. The micro-hybrid features can be summed up as: Engine shuts off while the vehicle is in motion and below approximately 8 kph. In emergency braking, the engine remains running to provide vacuum / hydraulic assist to the brakes. If the battery State of Charge (SOC) is low, the engine remains on to charge the battery via the alternator. If the temperature is above 300C, the engine remains on to sustain cabin air conditioning. When the temperature is below -50C, the engine stays on for cabin heating. A possible two cell Ultracapacitor module is designed to aid the battery by boosting voltage during engine cranking so the vehicle electrical distribution system voltage is stabilised. Micro-hybrid implementations come in two basic design varieties; 1. Belt integrated starter generator (B-ISG) or belt alternator starter (BAS) system. 2. Crankshaft mounted integrated starter generator (ISG). Internationally the most recognised mild hybrid early design (2006) is the BAS that GM put into production in the Saturn Vue Greenline hybrid as a 42 volt system (36 volt battery) and more recently in the Malibu Hybrid and the 2014 Buick LaCrosse Hybrid.
    [Show full text]
  • Piston Pump Service Manual
    PISTON PUMP SERVICE MANUAL 3 FRAME: 280, 281, 290, 291 10 FRAME: 621, 623, 820, 821, 825,1010,1011,1015 4 FRAME: 331, 333, 335, 430, 431, 435 25 FRAME: 1520,1521,1525, 2520, 2521, 2525, 2520C 5 FRAME: 323, 390 60 FRAME: 6020, 6021, 6024, 6040, 6041, 6044 INSTALLATION AND START-UP INFORMATION Optimum performance of the pump is dependent upon the entire liquid system and will be obtained only with the proper selection, installation of plumbing, and operation of the pump and accessories. SPECIFICATIONS: Maximum specifications refer to individual attributes. It is not DISCHARGE CONDITIONS: OPEN ALL VALVES BEFORE STARTING SYSTEM to implied that all maximums can be performed simultaneously. If more than one avoid deadhead overpressure condition and severe damage to the pump or system. maximum is considered, check with your CAT PUMPS supplier to confirm the Install a Pulsation Dampening device onto the discharge head or in the discharge proper performance and pump selection. Refer to individual pump Data Sheet for line. Be certain the pulsation dampener (Prrrrr-o-lator) is properly precharged for the complete specifications, parts list and exploded view. system pressure (refer to individual Data Sheet). LUBRICATION: Fill crankcase with special CAT PUMP oil per pump specifications A reliable Pressure Gauge should be installed near the discharge outlet of the high [3FR-10 oz., 4FR-21 oz., 5FR-21 oz.,10FR-40 oz., 25FR-84 oz., 60FR-10 Qts.]. DO pressure manifold. This is extremely important for adjusting pressure regulating NOT RUN PUMP WITHOUT OIL IN CRANKCASE. Change initial fill after 50 hours devices and also for proper sizing of the nozzle or restricting orifice.
    [Show full text]
  • A Case of Innovation in Response to Fuel Economy Regulation
    5 HE IE. A34 NO 3 . ORT NOS. DOT-TSC-NHTSA-79-18 HS-804 629 TSC- jJ HHTS4- THE DEVELOPMENT AND 79-18 INTRODUCTION OF THE AUTOMOTIVE TURBOCHARGER A Case of Innovation in Response to Fuel Economy Regulation Larry Ronan William Abernathy LEXINGTON TECHNOLOGY ASSOCIATES 10 Wingate Road Lexington MA 02173 AUGUST 1979 f _ DEPARTMENT J of TR A NS FINAL REPORT I FOR TATION SEP is 1979 library DOCUMENT IS AVAILABLE TO Tl- THROUGH THE NATIONAL TECHNICAL INFORMATION SERVICE, SPRINGFIELD, VIRGINIA 22161 f ' ( Prepared for . S ^DEPARTMENT OF TRANSPORTATION , NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION Office of Research and Development Washington DC 20590 . NOTICE This document is disseminated under the sponsorship of the Department of Transportation in the interest of information exchange. The United States Govern- ment assumes no liability for its contents or use thereof NOTICE The United States Government does not endorse pro- ducts or manufacturers. Trade or manufacturers' names appear herein solely because they are con- sidered essential to the object of this report. \ par Technical Report Documentation Page 1 . Report No. 2. Government Accession No. 3. Recipient's Catalog No. -i? _ HS-804 629 sk’ 7H 4. Title and Subtitle 5. Report Date THE DEVELOPMENT AND INTRODUCTION OF THE AUTOMOTIVE AUGUST 1979 TURBOCHARGER: A Case of Innovation in Response to 6. Performing- Organization Code Fuel Economy Regulation 8. Performing Orgonizotion Report No. 7. Authors) Larry Ronan and William Abernathy DOT-TSC-NHTSA-79-18 9. Performing Organization Name and Address 10. Work Unit No. (TRAIS) HS929/R9401 * Lexington Technology Associates 1 1 . Contract or Grant No.
    [Show full text]