OPEL Meriva

Owner’s Manual

Meriva_Introduction.fm Seite -1 Donnerstag, 10. September 2009 3:34 15

OPEL Meriva

Operation, Safety, Maintenance Meriva_Introduction.fm Seite 0 Donnerstag, 10. September 2009 3:34 15

Data specific to your vehicle Please enter your vehicle’s data here so that it is readily accessible. Please refer to the sections "Servicing and maintenance" and "Technical data" and the identification plate. Fuel Designation

Engine oil Grade

Viscosity

Tyre pressure Tyre size Front Rear Summer tyres

Winter tyres

Weights Gross vehicle weight rating

– EC kerb weight

= Loading Meriva_Introduction.fm Seite 1 Donnerstag, 10. September 2009 3:34 15

Introduction z The table of contents at the beginning of 3 signifies equipment not fitted to all vehi- Your vehicle is an intelligent combination the owner’s manual and within the indi- cles (model variants, engine options, mod- of forward-looking technology, impressive vidual chapters will show you where eve- els specific to one country, optional equip- safety, environmental friendliness and rything is. ment, Genuine Opel Parts and Accesso- economy. z Its index will help you find what you ries). It now lies with you to drive your vehicle want. Page references are indicated with 3. 3 safely and to see it performs perfectly. This z Yellow arrows in the illustrations serve as means "see page". Owner’s Manual provides you with all the points of reference or indicate some ac- 9 Danger, 9 Warning, Caution necessary information to that end. tion to be performed. Make sure your passengers are aware of z Black arrows in the illustrations indicate 9 Danger the possible risk of accident and injury a reaction or a second action to be per- which may result from improper use of the formed. Text marked 9 Danger provides infor- vehicle. z This Owner’s Manual depicts left-hand mation on risk of endangering life. Fail- You must always comply with the specific drive vehicles. Right-hand drive vehicles ure to comply with the instructions could laws of the country that you are in. These are operated in the same way. endanger life. laws may differ from the information in this z The Owner’s Manual uses the internal Owner’s Manual. engine codes. The corresponding sales 9 Warning When this Manual refers to a workshop vis- designations are found in the chapter it, we recommend your Opel Service Part- "Technical data". Text marked 9 Warning provides infor- ner. mation on risk of accident or injury. Fail- z Directional data, e.g. left or right, or ure to comply with the instructions could All Opel Service Partners provide first-class front or back, in the descriptions always lead to injury. service at reasonable prices. Experienced relate to the direction of travel. mechanics trained by Opel work according Symbols to specific Opel instructions. Caution 6 Continue reading on next page. The Owner’s Manual, infotainment system Text marked Caution provides informa- instructions and the vehicle Service and tion on possible damage to the vehicle Warranty Booklet should always be kept Failure to comply with the instructions ready to hand in the vehicle glove com- could lead to vehicle damage. partment. Make use of the Owner’s Manual Safe driving! z The "In Brief" section will give you an ini- GmbH tial overview. Meriva_Introduction.fm Seite 2 Donnerstag, 10. September 2009 3:34 15 In Brief ...... 2 Contents Keys, doors, windows, slide and tilt sunroof ...... 26 Seats, Interior ...... 44 Instruments, Controls ...... 82 Lighting ...... 102 Infotainment system ...... 111 Climate control ...... 114 Driving and operation ...... 129 Self-help, vehicle care ...... 165 Service and maintenance ...... 199 Technical Data ...... 218 Index ...... 234 2In Brief In Brief

Picture no: 15335T.tif Picture no: 13977s.tif To unlock the vehicle: Press To adjust front seat leg room: Pull button q handle, slide seat, release handle Open the door by pulling on the door Seats 3 44, Seat position 3 45. handle. To open the tailgate, pull on the button in the handle recess and pull the tailgate upwards. Door locks 3 26, key 3 26, remote control 3 28, central locking system 3 30, anti- theft locking system 3 3 31, tailgate 3 32, anti-theft alarm system 3 3 34. In Brief 3

Picture no: 13978s.tif Picture no: 13979s.tif Picture no: 13980s.tif To adjust front seat backrests: To adjust front seat height 3: Pull Head restraint height of front and Turn handwheel lever rear outer seats: Tip head Do not lean on seat backrest whilst Lift lever and relieve some weight from seat restraint forward to release, hold adjusting it. to raise it or press down on seat with body and adjust height, engage Seats 3 44, Seat position 3 45. weight to lower it. Head restraints 3 46, Centre rear head Seats 3 44, Seat position 3 45. restraint 3 47, Head restraint position 3 47, Head restraint removal 3 48. 4In Brief

Picture no: 18531s.tif Picture no: 14300s.tif Picture no: 13985s.tif Extend the seat belt and clip it To adjust interior mirror by Use the knob to move the exterior into the buckle swivelling mirrors in the appropriate The seat belt must not be twisted and must Swivel lever 3 on underside of mirror direction lie snugly against the body. The backrest housing to reduce dazzle. Mirror 3 36, Aspherical exterior mirrors 3 must not be tilted back too far (maximum Interior mirror 3 38, Automatic anti-dazzle 3 37, Swinging in exterior mirror 3 37. approx. 25 ). interior mirror 3 3 39. To release belt, press red button on belt buckle. Three-point seat belt 3 59, Airbag system 3 3 67, seat position 3 45. In Brief 5

Picture no: 16099s.tif Picture no: 13981s.tif Adjust exterior mirrors Steering adjustment 3: electrically 3 Swivel lever down, adjust height, Select the mirror to be adjusted using the swivel lever up, engage rocker switch and adjust using the four- Adjust steering wheel only when vehicle is way switch. stationary and steering wheel lock is Mirror 3 36, Aspherical exterior mirrors 3 released. 3 37, Swinging in exterior mirror 3 37, Airbag system 3 67, Steering wheel lock Heated exterior mirrors 3 3 13, 3 41. 3 15. 6In Brief In Brief 7

1 Parking lamps, dipped beam ... 3 102 9 Hazard warning lamps ... 3 12, 3 104 18 Brake pedal ...... 3 135, 3 151 3 Courtesy lamp ...... 108 LED for 19 Ignition switch 3 3 3 Instrument illumination ...... 108 anti-theft alarm system ...... 34 with steering wheel lock ...... 3 15 Rear fog lamp ...... 3 104 Heated seats 3 ...... 3 46 3 3 20 Steering wheel adjustment 3 ...... 3 5 Fog lamp ...... 103 10 Central information display 3 3 Headlamp range adjustment 104 for time, date, 21 pedal 3 ...... 3 135 2 Side Air vents ...... 3 115 outside temperature, 22 Bonnet release lever ...... 3 165 infotainment system 3 ...... 3 90 3 Horn ...... 3 12 23 Fuse box ...... 3 182 3 3 4 Indicators, headlamp flasher 11 Infotainment system ...... 111 Dipped beam, main beam...... 3 11 12 Front passenger airbag 3 ...... 3 67 3 3 Ambient lighting ...... 107 13 Glove compartment ...... 3 80 Cruise control 3...... 3 148 14 Climate control ...... 3 114 5 Steering wheel remote control 3 ...... 3 111 15 Air conditioning system 3 ...... 3 114 Heated rear window ...... 3 13, 3 41 3 6 Instruments ...... 82 Recirculation system 3...... 3 119 7 Windscreen wipers and 16 Ashtray ...... 3 79 windscreen washer system, Accessory socket and 3 headlamp washer system cigarette lighter ...... 3 78 and rear window washer system 3 ...... 3 12, 3 100 17 Accelerator pedal ...... 3 135, 3 137 8 Centre air vents ...... 3 115 8In Brief In Brief 9

1 Side air vents ...... 3 115 8 Horn ...... 3 12 15 Steering wheel adjustment 3 ...... 3 5 2 Front passenger airbag 3 ...... 3 67 9 Instruments ...... 3 82 16 Accelerator pedal ...... 3 135, 3 137 3 Infotainment system 3 ...... 3 111 10 Windscreen wipers, 17 Brake pedal ...... 3 135, 3 151 4 Hazard warning lamps .... 3 12, 3 104 windscreen washer system, 18 Clutch pedal 3 ...... 3 135 headlamp washer system 3 LED for 19 Ashtray ...... 3 79 3 3 and rear window anti-theft alarm system ...... 34 Accessory socket and 3 3 washer system 3 ...... 3 12, 3 100 Heated seats ...... 46 cigarette lighter ...... 3 78 3 5 Information display 11 Parking lamps, dipped beam .... 102 3 20 Air conditioning system 3 ...... 3 114 for time, date, Courtesy lamp ...... 108 3 Heated rear window ...... 3 13, 3 41 outside temperature, Instrument illumination ...... 108 3 Recirculation system 3...... 3 119 infotainment system 3 ...... 3 90 Fog tail lamp ...... 104 Fog lamp 3 ...... 3 103 21 Climate control ...... 3 114 6 Centre air vents ...... 3 115 Headlamp range adjustment 3 .3 104 22 Glove compartment ...... 3 80 7 Indicators, headlamp flasher 12 Bonnet release lever ...... 3 165 dipped beam, main beam ...... 3 11 23 Fuse box ...... 3 182 ambient lighting 3...... 3 107 13 Steering wheel remote 3 3 cruise control 3 ...... 3 148 control ...... 111 14 Ignition switch with steering wheel lock ...... 3 15 10 In Brief

Control indicators I Engine oil pressure, R Brake system, clutch system 3, 3 3 X Seat belt 3, 84. 85. 3 82. O Turn signal lamps, u Anti-lock Braking System 3, B Adaptive Forward Lighting 3 11, 3 84. 3 152. (AFL) 3, fault, 3 82, 3 106. C Main beam, S Engine oil level 3, 3 11, 3 84. 3 85. > Fog lamps 3, 3 83, 3 103. ! Preheating system 3, Diesel EPS Electric power steering 3, particle filter 3, 3 86. A Engine electronics, immobiliser, 3 86. 3, Fault, Electronic Stability Program v Plus 3 83, 3 27, 3 143. j Easytronic 3, starting the (ESP® ) 3, engine 3, 3 146. Z Exhaust gases 3, 3 130. 3 83, 3 143. Y Fuel level, T Easytronic 3, Winter 3 86, 3 140. v Airbag systems 3, Belt programme, tensioners, 3 132. y Seat occupancy recognition 3, 3 61, 3 72. 3 72, 3 73. m Cruise control 3, 3 148. r Fog tail lamp, 3 85, 3 104.

p Alternator, 3 85. In Brief 11

Picture no: 14727s.tif Picture no: 18475s.tif Picture no: 14054h.tif Exterior lights Headlamp flash, main beam and Turn signals Rotate dipped beam Right = Lever upwards 7 =Off Headlamp flash = Pull stalk towards Left = Lever downwards steering wheel 8 =Parking lamps Turn signal lamps 3 103. 9 = Dipped or main beam Main beam = Push stalk forwards Dipped beam = Push stalk forwards Press again > =Fog lamps 3 Main beam, headlamp flash 3 103. r = Fog tail lamp Lighting 3 102, headlamp warning device 3 17. 12 In Brief

Picture no: 14303s.tif Picture no: 13991s.tif Picture no: 14055h.tif Hazard warning flashers Horn: Press j Windscreen wipers Operated with the ¨ button. Airbag system 3 3 67, Steering wheel & =Fast 3 3 Hazard warning lamps 3 104. remote control 111. % =Slow $ = Timed interval wipe § =Off Windscreen wipers 3 100 adjustable intermittent setting 3 3 100, further information 3 198, 3 215. In Brief 13

Picture no: 14056h.tif Picture no: 14057h.tif Picture no: 13992s.tif Operating windscreen and Rear window wiper and washer Heated rear window, heated headlamp washer systems 3: system exterior mirrors 3 Pull stalk towards steering wheel Wiper on = Push stalk forwards Operated with the Ü button. The wipers will swipe for a few strokes. Wiper off = Pull stalk towards Climate control 3 114, Heated rear window The headlamp washer system 3 can be steering wheel 3 41. operated when the lights are on. Washing = Push lever forward Windscreen washer system and headlamp and hold washer system 3 3 101, Further Rear window wash and wipe system 3 101, information 3 198, 3 215. Wiper blades 3 215, care 3 198. 14 In Brief

Picture no: 13993s.tif Picture no: 16496s.tif Picture no: 15270s.tif To clear fogged or icy windows To set automatic mode of climate Manual Turn rotary switch for temperature and air control system 3 Reverse gear: With vehicle stationary, wait volume, for air flow also press V,for air Press AUTO button, select temperature 3 seconds after depressing the clutch, then conditioning system 3: button n, climate with rotary knob, open air vents. lift the ring below the gear knob and control 3: button V. engage gear. Climate control system 3 3 122. Climate control 3 114, Air conditioning If the gear does not engage, set the lever in system 3 3 119, Climate control system 3 neutral, release the clutch pedal and 3 122. depress again; then repeat gear selection. 3 14. In Brief 15

Before starting off, check z Tyre pressure and tyre condition 3 155, 3 228. z Engine oil level and fluid levels 3 209 to 3 216. z All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and operational. z Seats, seat belts and mirrors are correctly adjusted. 3 44, 3 59, 3 36. z Check brake function at low speed, particularly if the brakes are wet. Picture no: 14175s.tif Picture no: 15678t.tif Automated manual Steering wheel lock and ignition transmission 3 Turn key to position 1. Move the steering N = Idle/start position wheel slightly to release the steering wheel o =Driving position lock. + =Higher gear 0 = Ignition off - =Lower gear 1 =Steering free, ignition off A/M = Switch between Automatic and 2 = Ignition on, with : pre- Manual mode heating R = Reverse gear 3 =Starting (with selector lever lock) To move the selector lever from N to R press the button on the lever. Only start in N with foot brake applied. Automated manual transmission 3 3 129. 16 In Brief

Parking the vehicle z Always apply the handbrake without pressing the release button. On an incline, apply as tight as possible. To reduce activation force, depress foot brake at the same time. z Switch off engine and ignition. Turn the ignition key to position 0 and pull it out. Turn the steering wheel until it is clear that the steering lock has engaged (anti- theft protection). On vehicles with manual transmission automated 3, control indicator R flashes for a few seconds after the Picture no: 15582a.tif Picture no: 14714s.tif ignition is switched off if the hand brake Starting the engine Releasing the hand brake: Raise has not been applied. Depress clutch and brake, manual lever slightly, Press release z If the vehicle is on the flat or on an transmission automated 3 in N, do not button, Lower lever fully incline, engage first gear before press the accelerator, in diesel engine Hand brake 3 153. switching off the ignition. On an uphill vehicles turn the key to positing 2 until the slope, also turn the front out from warning lamp ! goes out, turn key to the kerb. position 3; let go of the key when the engine is running. If the vehicle is facing downhill, engage reverse gear before switching off the Before restarting or switching off the ignition. Also turn the front wheels into engine, turn key back to 0. the kerb. To switch on the ignition, only turn the key z Lock the vehicle by pressing button p on to 2. the remote key fob. To activate the anti-theft locking system 3 and anti-theft alarm system 3, press button p twice. In Brief 17

Advice when parking Interesting functions z Do not park the vehicle on flammable ground as combustion could occur due to the high exhaust temperatures. z Close window, sliding roof 3 and tilting roof 3. z The engine cooling fans may run after the engine has been switched off, 3 209. z After running at high engine speeds or with high engine loads, operate the engine briefly at a low load or run in neutral for approx. 30 seconds before switching off in order to protect the turbocharger 3. Remote control 3 28, central locking system 3 30, anti-theft warning system 3 3 34, parking vehicle for longer periods 3 217. 18 In Brief

Flexible Seat System (FlexSpace) The back seat of your vehicle has three seats or, with the centre seat lowered, two seats with maximum seating space. The outer seats can be lowered to obtain a level loading surface.

Picture no: 14178s.tif Picture no: 14179s.tif Sliding outboard rear seats front-rear Adjust or fold backrest of rear outboard z Pull handle under seat. seats z z Slide seat. Pull handle on outboard side of seat. z z Release handle and allow seat to Guide backrest into the relevant position. engage in position. z Release handle and allow seat to audibly When pushing the seats back, to prevent engage in position. damage make sure the backrests are not in their furthest back position. In Brief 19

The backrest can engage in several positions. In addition, the backrest can be folded all the way down to the seat when extending the luggage compartment.

9 Warning To prevent injuries, always hold back seat backrest firmly and guide downward when folding.

Picture no: 14728s.tif Picture no: 14730s.tif Lower centre seat Variant 1 with three rear seats z House centre seat belt in the holder in z Adjust backrest to centre position. the roof. z Pull handle beneath seat. Slide seat all z Insert seat belts into recesses in seat the way forward, then outward toward cushion. the door and then further forward to the z Slide centre seat head rest all the way desired position. down. z Release handle and allow seat to z Pull release handle at rear of centre engage in position. backrest. Tilt backrest forward and z Raise centre seat. engage. 20 In Brief

Picture no: 14729s.tif Picture no: 14716s.tif Picture no: 14125s.tif Variant 2 with two rear seats, with Lower outboard seats Airbag system maximum seating space z Pull seat belt from belt guide at backrest. The airbag system consists of several z Lower centre seat. z Fold down outboard rear seat backrests. internal systems. z Adjust backrest to centre position. z To achieve a level loading surface, pull Front airbag system z Pull handle beneath seat. Slide seat all release handle on back of backrest and The front airbag system will be triggered in the way back, then toward the centre of push seat down until it latches into the event of a serious accident involving a the vehicle and then further rearward to position. frontal impact and forms safety cushions the desired position. for the driver and front passenger. The forward movement of the driver and front z Release handle and allow seat to passenger is checked and the risk of engage in position. injuries to the upper body and head thereby substantially reduced. In Brief 21

Picture no: 14742s.tif Picture no: 14127s.tif Picture no: 14287j.tif Side airbag system 3 Curtain airbag system 3 Active head restraints 3 on front The side airbag is triggered in the event of In the event of a side-on collision, the seats a side-on collision to form a safety cushion curtain airbag system triggers and In the event of a rear-end impact, the for the driver or front passenger in the provides a safety barrier in the head area active head restraints tilt forwards slightly. respective door area. This substantially of the vehicle. This considerably reduces The head is more effectively supported by reduces the risk of injury to the upper body the risk of injury to the head in the event of the head restraint and the risk of whiplash and pelvis. a side-on collision. injury is reduced. 3 3 Airbag System 67. Active head restraints can be recognised by the word ACTIVE. Head restraints 3 46. 22 In Brief

Picture no: 14304s.tif Picture no: 14315s.tif Picture no: 15593t.tif Travel Assistant 3 Dismantling the Travel Assistant Operating menus via the The Travel Assistant Contains z Press lower button on the information display 3 z Armrest. Travel Assistant. Menu options are selected using menus z Tray. z Pull Travel Assistant upwards out of and using the buttons/four-way button or recesses. the multifunction button of the z Drink holders. 3 3 z There is a carrying handle on the back to Infotainment system or the buttons on The Travel Assistant is mounted on the facilitate transport. the steering wheel. The respective menu lowered centre seat. options are shown on the display. Selection using four-way button: press four-way button at top, bottom, left or right. In Brief 23

Ü Board Computer 19,5° 19:36 BC 1 All values

BC 2 257.0 km Timer 1 Ø40km/h

31.0 Ltr. 8 Ø 7.0 Ltr./100km

Picture no: 15559t.tif Picture no: 14034s.tif Picture no: 16719t.tif Selection using multifunction button 3: To select with steering wheel buttons 3 Trip computer 3 rotate and press multifunction button. Select menu options via the menus and the Functions: To exit a menu, turn the multifunction buttons. z Range button left or right to Return or Main and Information display 3 90. z Instantaneous consumption select. z Distance travelled z Average speed z Effective consumption z Average consumption z Stop watch Trip computer 3 97. 24 In Brief

Picture no: 14034s.tif Picture no: 14035s.tif Picture no: 14779s.tif Steering wheel remote control 3 Rear seat audio system 3 Ultrasonic parking sensors 3 The functions of the infotainment system Twin Audio allows rear seat occupants the When reverse gear is selected, the park and the information display can be choice between the audio source played on pilot switches itself on automatically. operated with the remote control on the the Infotainment system or the alternative An acoustic warning sounds when the steering wheel. audio source. vehicle approaches an obstacle behind. 3 3 3 3 Steering wheel remote control 111, Rear seat audio system 112. Ultrasonic parking sensors 3 3 150. Infotainment system 3 111. In Brief 25

The lamp beam projects at a 90 angle to the left or right of the vehicle up to a distance of approx. 30 metres. Reversing function Turning the lights on, selecting reverse gear and activating the turn signal activates the cornering light for the relevant side. When the turn signal is switched off, the cornering light continues to illuminate for 15 seconds. Adaptive forward lighting 3 3 106. Diesel particle filter 3 The diesel particle filter system filters Picture no: 18604s.tif harmful soot particles out of the exhaust Picture no: 18600S.tif Adaptive Headlight (AFL) 3 gases. The system includes a self-cleaning Under certain driving conditions, e.g. short The system provides better illumination of function that run automatically during journeys, the system may not clean itself the road on corners and curves. driving. The filter is cleaned by burning off automatically. the soot particles at high temperature. Curve lighting If the filter requires cleaning and previous This process takes place automatically driving conditions did not enable The light beam pivots based on under set driving conditions and may take steering wheel position and speed automatic cleaning, control indicator ! up to 25 minutes. Fuel consumption may flashes. (from approx. 10 km/h). be higher during this period. The emission The headlamps shine at an angle of up of smells and smoke during this process is Further instructions 3 144. to 15 to the right or left of the direction of normal. travel. Cornering light An additional lamp comes on at certain steering wheel settings (after rotation of approx. 90 ), turn signal settings and speeds (up to approx. 40 km/h). 26 Keys, doors, windows, slide and tilt sunroof

Keys, doors, windows, Replacement keys The key number is specified in the slide and tilt sunroof Car Pass 3. The key is part of the electronic immobiliser. Locks 3 198.

Replacement keys ...... 26 Key with retractable key blade 3 ...... 26 Car Pass...... 26 Electronic immobiliser...... 27 Picture no: 15760t.tif 3 Radio remote control ...... 28 Key with retractable key blade Central locking system ...... 30 Press button to extend. To retract, press Malfunction in remote control ...... 32 button and audibly engage key blade. Malfunction in central Car Pass locking system ...... 32 The Car Pass contains safety-related Tailgate ...... 32 vehicle data and should therefore be kept Anti-theft alarm system 3 ...... 34 in a safe place. Child safety locks...... 36 When the car is taken to a workshop, the Exterior mirrors...... 36 Car Pass data is needed in order to Interior mirror ...... 38 perform certain operations. Manual window operation...... 39 Electric windows 3...... 39 Sun roof and tilting roof 3...... 42 Keys, doors, windows, slide and tilt sunroof 27

If control indicator A illuminates after the engine has started, there is a fault in the engine electronics or transmission electronics 3 3 83, 3 133, 3 143 or there is water in the diesel fuel filter 3 3 212. Note The immobiliser does not lock the doors. Therefore, always lock the vehicle before leaving it unattended and enable the anti-theft alarm system 3 3 34.

Picture no: 15761t.tif Picture no: 17880s.tif Electronic immobiliser Control indicator for immobilizer A The system checks whether the vehicle is Control indicator A illuminates briefly allowed to start with the key used. Once when the ignition is switched on. the transponder in the key is recognised, If the control indicator flashes when the the vehicle can be started. ignition is on, there is a fault in the system; The electronic immobiliser activates the engine cannot be started. Switch off automatically when the key is removed the ignition and then repeat the start from the ignition switch. attempt. If the control indicator A continues to flash, please try to start the engine using the second key and contact a workshop. 28 Keys, doors, windows, slide and tilt sunroof

Radio remote control Depending on equipment level, the vehicle comes equipped with one of the remote controls depicted on this page. The remote control is integrated in the key. Used to operate: z Central locking system, z Mechanical anti-theft locking system 3, z Anti-theft alarm system 3. In vehicles with electric windows in all doors 3, the radio remote control can be used to closed the windows.

Picture no: 15330t.tif Picture no: 15331t.tif The remote control has a range of Handle the remote control with care, approx. 5 metres. This range can be protect it from moisture and high affected by outside influences. Aim the temperatures and avoid unnecessary remote control at the vehicle to operate. operation. The hazard warning lamps flash to confirm remote control operation. Keys, doors, windows, slide and tilt sunroof 29

Fault Key with fixed key bit, see Fig. 15331 T on If the central locking system cannot be previous page. operated with the remote control, it may be Have the battery changed in a workshop. due to the following: Synchronise remote control z Range exceeded. After changing the battery, unlock the z Remote control battery voltage too low. door using the key in the lock. The radio Change battery. remote control is synchronised by inserting z Operating the remote control several the key in the ignition lock. times in quick succession outside the range of the vehicle can result in the remote control no longer being recognised so that it has to be re- synchronised. Picture no: 15332t.tif z If the central locking system is Remote control battery replacement overloaded as a result of repeated Replace the battery as soon as the range operation at short intervals. The power of the remote control begins to shrink. supply is cut off for a brief period. Batteries do not belong in household z Interference from higher-power radio waste. They must be disposed of at an waves from other sources. appropriate recycling collection point. Opening the vehicle 3 32. Key with retractable key blade, see Fig. 15330 T on previous page. Extend the key 3 26. Open the remote control. Replace the battery (battery type CR 20 32), noting installation position. Close the remote control and synchronise. 30 Keys, doors, windows, slide and tilt sunroof

When the mechanical anti-theft locking system 3 is enabled, the doors cannot be unlocked by pulling up the lock buttons. Country-specific version 3: pressing once unlocks the driver’s door, and pressing twice unlocks the entire vehicle.

Picture no: 15335t.tif Picture no: 15333t.tif Central locking system To lock Unlock and lock doors, tailgate and fuel Close doors, luggage compartment and filler flap. tank flap. To unlock Press button p of the radio remote control Press button q on remote control – or from the inside – – or from the inside – Press lock button on driver’s door when the Release lock button on driver’s door. doors are closed. To open the door, pull the handle. Open the luggage compartment by pulling the button in the handle recess. Keys, doors, windows, slide and tilt sunroof 31

Within 10 seconds of locking, press the Fault p button on the remote control again. If the central locking cannot be operated, The mechanical anti-theft locking system is this can be for one of the following reasons: switched off when the vehicle is unlocked. z If the central locking system is Note overloaded as a result of repeated z To prevent the driver from being operation at short intervals. The power inadvertently locked out, the button on supply is cut off for a brief period. the driver’s door cannot be depressed z Faulty fuse in fuse box 3 182. when the door is open. To eliminate the cause of the fault, contact z If the driver’s door is not closed properly, a workshop. the central locking system will unlock Opening driver’s door with key. again immediately after locking. z The doors lock again automatically a Picture no: 15334t.tif short time after unlocking the vehicle Mechanical anti-theft locking system 3 using the remote control if no door is opened in the meantime. 9 Warning z To lock the doors from inside (e.g. to Do not use the system if there are people prevent unwanted entry from outside), in the vehicle! The doors cannot be push down lock button on driver’s door. unlocked from the inside. z Locked doors unlock automatically if an accident of a certain severity occurs (to All doors must be closed. permit outside assistance) – Prerequisite: If the ignition was on, the driver’s door Ignition must not be switched off. must be opened and closed once so that the vehicle can be secured. All doors are secured against opening. 32 Keys, doors, windows, slide and tilt sunroof

Malfunction in central locking system To unlock Turn key anticlockwise in driver’s door lock, return to the vertical position and remove. The driver’s door is unlocked. The other doors can be unlocked by pulling the interior lock buttons (not possible if the anti-theft locking system is enabled 3). Switch on the ignition to deactivate the anti-theft alarm system 3. To lock With the driver’s door open, press the interior lock button of the other doors. Picture no: 17881s.tif Close the driver’s door. Turn the key Picture no: 15335t.tif Malfunction in remote control clockwise in the lock, return to the vertical Tailgate To unlock position and remove. The fuel filler flap To unlock Turn key anticlockwise in driver’s door lock, cannot be locked. Press button q on the remote control, the return to the vertical position and remove. tailgate and the doors will be unlocked. The entire vehicle is unlocked. Switch on the ignition to deactivate the anti-theft alarm system 3. To lock With the driver’s door closed, turn the key clockwise in the lock, return to the vertical position and remove. The entire vehicle is locked. Keys, doors, windows, slide and tilt sunroof 33

Picture no: 17873s.tif Picture no: 17882s.tif Picture no: 15333t.tif To open To close To lock The tailgate is opened by pulling on the Close the tailgate using the handle on the Press button p on radio remote control. button in the handle recess. inside of the tailgate. Do not press the release button in the trim 9 Warning recess while closing as this will unlock it Do not drive with the tailgate open or again. ajar, e.g. when transporting bulky objects, since toxic exhaust gas could penetrate the interior.

After fitting certain accessories, it might not be possible to keep the tailgate in the open position. 34 Keys, doors, windows, slide and tilt sunroof

Anti-theft alarm system 3 Monitors z the doors, luggage compartment, bonnet. z the passenger compartment. z vehicle tilt, e.g. if it is raised. z the ignition.

9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. Picture no: 15334t.tif Picture no: 11575s.tif To activate Activation without monitoring of All doors, windows, sun roof 3, tilting passenger compartment and vehicle tilt roof 3 and bonnet must be closed. Press Switch on e.g. if animals are to be left in the button p on the radio remote control vehicle. again within 10 seconds of locking. 1. Close tailgate and bonnet. If the ignition was switched on, the driver’s 2. Press button in front of the courtesy lamp door must be opened and closed once so (with ignition off); LED in the hazard that the anti-theft alarm system can be warning lamp button flashes a switched on. maximum of 10 seconds. 3. Close doors. 4. Activate the anti-theft alarm system. The LED lights up. After approx. 10 seconds, the system is activated. The LED flashes until the system is deactivated. Keys, doors, windows, slide and tilt sunroof 35

After the first 10 seconds of anti-theft alarm system activation: z LED flashes =System switched on, slowly z LED comes on for = Switch-off function. approx. 1 second Contact a workshop for assistance if problems are encountered.

Picture no: 14046s.tif Picture no: 15335t.tif Light emitting diode (LED) To deactivate During the first 10 seconds of anti-theft Press button q on remote control unit alarm system activation: – or – z LED comes on =Test, delayed switch on ignition. switch-on, In the case of a malfunction in the remote z LED flashes = Door, tailgate or control, use the key to unlock the vehicle rapidly bonnet open, or 3 32. system fault. If the alarm is triggered when the driver’s door is opened, deactivate the anti-theft alarm system by switching on the ignition. 36 Keys, doors, windows, slide and tilt sunroof

Note z Changes to the vehicle interior, such as the use of seat covers, could impair the function of passenger compartment monitoring. z Switch off the interior monitoring system when the interior of a parked vehicle is being heated. Alarm When triggered, the alarm gives off an acoustic signal (horn) and a visual signal (hazard warning flashers). The number and duration of the alarms are stipulated by legislation. The alarm can be silenced by pressing a Picture no: 16102s.tif Picture no: 13985s.tif button on the remote control or by Child safety locks Exterior mirrors switching on the ignition. The anti-theft Adjust manually with the handles in the 9 alarm system is deactivated at the same Warning front door or electrically 3 with the switch time. Use the child safety lock whenever in the driver’s door console. children are occupying the rear seats. Adjust exterior mirrors manually Use the knob to move the exterior mirrors in Turn rotary knob at rear door lock from the appropriate direction. vertical position using key: door cannot be opened from the inside. Keys, doors, windows, slide and tilt sunroof 37

Picture no: 16099s.tif Picture no: 15279s.tif Picture no: 14138s.tif Adjust exterior mirrors electrically 3 To retract exterior mirrors For the safety of pedestrians, the exterior Select the mirror to be adjusted using the Manual: The exterior mirrors can be folded mirrors will swing out of their normal rocker switch and adjust using the four- in by a slight pressure on the outer edge of mounting position if they are bumped with way switch. the housing. sufficient force. Reposition the mirror by Aspherical exterior mirror 3 Electric 3: Press button and both exterior applying slight pressure to the mirror The aspherical mirror glass makes the blind mirrors fold in. housing. angle smaller. The curvature makes objects Press button again and both exterior look smaller, making it more difficult to mirrors swivel back to the driving position. estimate how far away following vehicles are. If a mirror has been manually adjusted, swivel in both mirrors by hand and then press the button. After electrical operation, there is a 6 second delay before it can be swung again. 38 Keys, doors, windows, slide and tilt sunroof

Picture no: 13992s.tif Picture no: 16502s.tif Picture no: 14300s.tif Heated exterior mirrors 3 On vehicles with electronic climate control Interior mirror Heating is activated or deactivated by Ü appears on the climate control display. Swivel mirror housing to adjust. pressing the Ü button. Heating works with the engine running and Manual anti-dazzle interior mirror is switched off automatically after a few To reduce dazzle, swivel the lever on the minutes. underside of the mirror housing. Keys, doors, windows, slide and tilt sunroof 39

Electric windows 3 9 Warning Take care when operating the electric windows. Risk of injury, particularly to children. If there are children on the rear seat, switch on the child safety system 3 for the electric windows. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Operational readiness Picture no: 13984s.tif Picture no: 14137s.tif Operable when the ignition key is in Automatic:Anti-dazzle interior mirror 3 Manual window operation position 1. Dazzling at night is reduced automatically. The door windows can be operated using Button illumination indicates operational The interior mirror does not reduce dazzle window winders. readiness. when: Operational readiness ends when the z the ignition is switched off. driver’s door is opened. z reverse gear is engaged or selector lever set to R. z interior lighting has been switched on. 40 Keys, doors, windows, slide and tilt sunroof

Picture no: 14804s.tif Picture no: 14140s.tif Picture no: 17899s.tif Operation Child safety system for rear windows 3 Closing windows 3 from outside To operate window in stages, tap Switch between the rocker switches in the On vehicles with electric windows in all appropriate switch. For automatic opening handle on the driver’s door doors, the windows can be closed from or closing, keep switch pressed for slightly z to left (red control indicator visible): rear outside: p longer; to stop window movement, tap windows cannot be operated with the Hold button of the remote control switch again. rocker buttons in the rear doors, depressed until all of the windows have closed completely. Safety function z to right (green control indicator visible): If the window glass encounters resistance rear windows can be operated with the above the middle of the window during rocker buttons in the rear doors. automatic closing, it is immediately stopped and the window opened again. If the windows do not move easily (e.g. on account of frost), repeatedly tap the switch for the window in question until the window has been closed in stages. Keys, doors, windows, slide and tilt sunroof 41

Overload If the windows are repeatedly operated at short intervals, the power supply is briefly cut off. Fault If the windows cannot be opened and closed automatically, activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Close the window completely and hold the rocker switch down at least 5seconds longer. Picture no: 13992s.tif Picture no: 16502s.tif 4. Open the window completely and hold Heated rear window 3 On vehicles with electronic climate the rocker switch down at least 1 second Heating is activated or deactivated by control Ü appears on the climate control longer. pressing the Ü button. display. 5. Repeat for each window. Heating works with the engine running and is switched off automatically after a few minutes. The heated rear window automatically switches on when the diesel particle filter is being cleaned 3 depending on the engine. Climate control 3 114. 42 Keys, doors, windows, slide and tilt sunroof

Front roof (sliding sun roof) Left rocker switch l and \ between the sun visors. Operable when the ignition is on. To open: Press button I, sun roof opens. To stop the movement, press button again. To close Press button \ until the sun roof is closed. To raise With the sun roof closed, press button \ until sun roof is open. To lower Picture no: 14251s.tif Press button l until the sun roof is closed. Picture no: 14143s.tif Sun roof and tilting roof 3 Rear roof (tilting sun roof) Right rocker switch \ and w between the 9 Warning sun visors. Operable with the ignition is on. Take care when operating the sunroof 3 To raise and the slide/tilt roof 3. Risk of injury, Press button \ until tilting roof has been especially for children. raised. Keep a close watch on the sun roof when To lower it is being closed. Ensure that nothing Press button w until tilting roof has closed. becomes trapped. Keys, doors, windows, slide and tilt sunroof 43

Sun shade To reduce the sunlight in the interior with the sliding roof closed or raised. Open or close sun shade as required. When the sun roof is opened, the sun shade is also opened. Note z If the top of the roof is wet, raise roof, allow water to run off and then open roof. z When using a roof rack, check the clearance of the sun roof to avoid damage. Picture no: 14802s.tif Picture no: 14803s.tif Fault Use a screwdriver 3 to push the If the electric drive fails, the system is in and turn until the sunroof or slide/tilt roof protected by a fuse in the fuse box 3 181. is closed. Until the fault is remedied, operate the sun roof as follows: Push drive cover backwards. 44 Seats, Interior Seats, Interior

Front seats ...... 44 Head restraints ...... 46 Armrest 3 ...... 48 Travel Assistant 3 ...... 48 Rear seats...... 51 Flexible Seat System (FlexSpace)...... 52 Luggage compartment extension ..... 53 Luggage compartment cover 3...... 55 Safety net 3 ...... 56 Lashing eyes ...... 57 Bag hangers 3...... 57 Picture no: 13977s.tif Picture no: 13978s.tif Notes on loading the vehicle...... 58 Front seats Adjusting the backrests Three-stage safety system...... 59 Take the pressure off the backrest and turn 9 Warning the hand wheel on the side. Three-point seat belts ...... 59 Belt tensioners...... 60 Never adjust seats while driving. They Using the belts ...... 62 may make uncontrolled movements. Mounting clips 3 for ISOFIX child restraint systems ...... 64 Adjust longitudinal seat position Pull handle at front of seat, move seat and Child restraint system 3...... 65 then release handle. Airbag system...... 67 Cigarette lighter 3...... 78 Accessory sockets 3 ...... 78 Ashtrays ...... 79 Stowage compartments...... 80 Foldaway tables 3 ...... 81 Coin holder 3 ...... 81 Sun visors...... 81 Seats, Interior 45

Picture no: 13979s.tif Picture no: 16098s.tif Picture no: 18530s.tif Adjusting the seat height 3 Adjusting the lumbar support 3 Seat position Lift front side lever and relieve some weight Turn side hand wheel on backrest while from seat to raise it or press down on seat relieving the load on the backrest. 9 Warning with body weight to lower it. Only drive with the seat correctly adjusted. z Sit with your buttocks as far back against the backrest as possible. Adjust the distance between your feet and the pedals so that your legs are slightly angled when pressing the pedals. Slide the passenger seat as far back as possible. 46 Seats, Interior z Sit with your shoulders as far back against the backrest as possible. Set the backrest rake so that you can easily reach the steering wheel with your arms slightly bent. Maintain contact between your shoulders and the backrest when turning the steering wheel. Do not angle the backrest too far back. We recommend a maximum rake of approx. 25 . z Adjust the steering wheel 3 5. z Set seat height 3 high enough to have a clear field of vision on all sides and of all display instruments. There should be at least six inches of clearance between Picture no: 14153s.tif Picture no: 13980s.tif your head and the headlining. Your Heated front seats 3 Head restraints thighs should rest lightly on the seat Two buttons between the centre air vents Adjusting the front head restraints and without pressing into it. for the left and right seats. the rear outboard head restraints 3 z Adjust the head restraint. To heat with the ignition switched on, press Tip head restraint forward, hold and adjust button ß. height. z Adjust the height of the seat belt 3 62. To fold over the rear seats or lower the z 3 Adjust the lumbar support so that it front passenger seat head restraint all the supports the natural shape of the spine. way down and remove, see next page. With the seats occupied, adjust height according to body size. Seats, Interior 47

Picture no: 14102s.tif Picture no: 14101s.tif Picture no: 14287j.tif Adjusting the rear centre head restraint Head restraint position Active head restraints 3 on front seats Pull head restraint upwards, press springs In the event of a rear-end impact, the and push head restraint down. 9 Warning active head restraints automatically tilt To improve visibility push headrest down slightly forward. The head is more Only drive with the head restraint set to effectively supported by the head restraint as far as possible if middle seat is the proper position. unoccupied or to increase the size of the and the danger of injury in the area of the cervical vertebra is reduced. luggage compartment. The middle of the head restraint should be Fold down centre seat 3 54. at eye level. If this is not possible for Active head restraints can be recognised extremely tall persons, set to highest by the word ACTIVE. If centre seat is occupied, pull head position, and set to lowest position for restraint upwards. small persons. 48 Seats, Interior

Picture no: 11581s.tif Picture no: 14738s.tif Picture no: 14304s.tif Removing Armrest 3 Travel Assistant 3 Press and release the two catches. Pull and Armrest at driver’s seat The Travel Assistant Contains remove the head restraint. Push raised armrest backward against z Armrest, To fold down the rear seat backrests 3 resistance and fold down. z Tray, 3 53, push rear head restraints fully down. The armrest can be moved to different z Drink holders. Note positions in stages by lifting it. Only approved objects or components The Travel Assistant is mounted on the If the armrest is not required, it can be lowered centre seat 3 54. must be attached to the head restraint of folded up. the unoccupied front passenger seat. Armrest 3 between rear seats See "Travel Assistant, armrest" 3 49. Seats, Interior 49

Picture no: 14310s.tif Picture no: 14311s.tif Picture no: 14312s.tif Installing The Travel Assistant Fold Travel Assistant down and audibly Armrest Lower centre seat 3 54. engage in front recesses. The arm rest can be moved and therefore Insert Travel Assistant in rear recesses on adapted to the position of the outboard back of middle seat. 9 Warning seats. If it is not correctly engaged, the Travel Assistant can be propelled forward with considerable force if hard braking occurs, possibly causing injury. 50 Seats, Interior

Picture no: 14313s.tif Picture no: 14314s.tif Picture no: 14315s.tif Tray Drink holder Dismantling the Travel Assistant There is a tray beneath the armrest. Open Open drink holder on front by pressing Press lower button on the Travel Assistant. tray by pushing upper button. front face. Seats, Interior 51

Picture no: 14316s.tif Picture no: 14178s.tif Picture no: 14179s.tif Pull Travel Assistant upwards out of Rear seats Adjust backrest rake of rear outboard recesses. Sliding outboard rear seats front-rear seats There is a carrying handle on the back to The rear outboard seats can be Grasp backrest, pull handle at outboard facilitate transport. individually adjusted front-rear. side of seat and guide backrest, unloaded, into the required position. Release handle It is not necessary to remove the Travel Pull handle under seat, move seat, release and allow backrest to engage. Assistant if you wish to raise the centre handle and allow seat to engage. seat, however, the armrest must be pushed The backrest rake can be set in three When pushing the seats back, to prevent positions. forwards. Be careful of any items in the damage make sure the backrests are not in Travel Assistant. their furthest back position. 52 Seats, Interior

Flexible Seat System (FlexSpace) 9 Warning The rear seat row on the Meriva can be To prevent injuries, always hold back fitted with three seats in Variant 1, or two seat backrest firmly and guide seats with maximum seating space in downward when folding. Variant 2. In Variant 2, the centre seat is lowered. To achieve a flat loading surface in the extended luggage compartment, the The luggage compartment can only be 3 outboard seats can be lowered slightly. We extended in Variant 1 53. recommend however only using the seats To extend the luggage compartment, the as seats in the raised position. Extending outboard seats can be lowered slightly the luggage compartment 3 53. 3 54.

Picture no: 14730s.tif Variant 1: Three rear seats Set seat backrest to centre position using the handle on the outside of the seat 3 51. Pull the handle beneath the seat. Slide the seat all the way forward, then outward toward the door and then further forward to the desired position. Release handle and allow seat to engage in position. Raise centre seat 3 54. Seats, Interior 53

Luggage compartment extension To increase the size of the luggage compartment you can z fold down the outboard rear seat backrests, z lower the middle seat, z lower the folded outboard seats, z fold down the passenger seat backrest 3, see following instructions. The rear seats must also be in "Variant 1: Three rear seats" 3 52. Picture no: 14729s.tif Picture no: 14184s.tif Variant 2: Two rear seats Fold down the outboard rear seat Lower the centre seat by pulling the release backrests handle on the back of the centre seat Remove the luggage compartment backrest, fold backrest forward and cover 3 if necessary 3 55. 3 engage 54. Push head restraints down fully, 3 3, 3 46. Set seat backrest to centre position using Take seat belt out of the belt guide on the the handle on the outside of the seat 3 51. backrest. Pull the handle beneath the seat. Slide the Remove the push-in sleeves 3 for seat all the way back, then inward toward mounting the ISO-FIX child restraint the middle of the vehicle, and then further system – see separate instructions for the back to the desired position ISO-FIX child restraint system. Release handle and allow seat to engage in position. 54 Seats, Interior

Picture no: 14182s.tif Picture no: 14728s.tif Picture no: 14716s.tif Grasp the backrest, pull the handle at the Fold the centre seat forward and lower. Raise centre seat outboard side of the seat and fold the House centre seat belt in the holder in the Pull release handle on the back of the backrest onto the seat. Release the handle ceiling 3 63. backrest, erect the backrest and engage, and engage the backrest. Insert seat belts into recesses in seat the outer seats must be in the outer cushion. position, see Variant 1: Three rear seats 9 Warning 3 52. Slide centre seat head rest all the way To prevent injuries, always hold the seat down 3 47. Lower outboard seats backrest firmly and guide downward Push front seat forward and fully lower or Pull release handle on the back of the when folding. remove head restraints on the rear centre seat backrest, see figure. Fold outboard seats 3 47. To raise, pull the handle on the outboard backrest forward and engage. The entire seat is lowered. Fold outer rear seat backrests onto seat side of the seat and raise the backrest. bases. Release the handle and engage. 9 Warning To achieve a level loading surface, pull Insert the seat belt into the belt guide at release handle on back of backrest and backrest. The load must not hinder the operation push seat down until it latches into of the hand brake or gear lever 3 58. position. Seats, Interior 55

Raise outboard seats Pull release handle on back of backrest and pull seat upward until it engages. Pull handle on outboard side of rear seat and move rear seat backrest upright. Release handle and latch. Insert the seat belt into the belt guide at backrest. The backrest can be raised to an upright position even with the seat lowered. We recommend however only using the seat as a seat in the higher position.

Picture no: 14107S.tif Picture no: 14735S.tif Fold down passenger seat backrest 3 Luggage compartment cover 3 Push head restraint all the way down or Do not place any heavy or sharp-edged remove 3 3, 3 46. objects on the cover. Push front passenger seat back. To open Lift release lever and fold front passenger Lift cover at rear and tilt forward segment seat backrest down. by segment. Raise front passenger seat backrest 3 To close Press release lever forward, restore Tilt top part of cover backward and latch passenger seat backrest to upright into position. position and engage audibly. 56 Seats, Interior

Picture no: 15272s.tif Picture no: 14736s.tif Picture no: 17952S.tif Removing Safety net 3 Hook the net straps into slots on the outer Open cover, disengage toward the rear The safety net can be mounted behind the seat bracket of the front seats and tighten. and remove from above. front seats. The rear seat backrests are When the safety net is fitted for the first Fitting folded forward. time, the slots on the outer seat consoles of Insert the cover from the rear, clip into Passengers must not be carried behind the the front seats must be opened once: press place and fold back. safety net. marked area on upper edge with a blunt object and bend inward. Fitting The safety net is in the luggage Removing compartment below the floor covering, see Tilt strap length adjuster upwards and right-hand column. unhook straps at bottom. Unhook upper net rod and close mounting openings. Fold all rear seat backrests forward, see Extending the luggage compartment 3 53. The roof frame contains two mounting openings: Open covers. Hang the upper net rod first in one opening and then in the other side; clip in place forwards. Seats, Interior 57

Picture no: 16145s.tif Picture no: 14718s.tif Picture no: 14717s.tif Stowage of safety net Lashing eyes Bag hangers 3 Roll up the removed safety net and secure Lashing eyes are provided to secure There are two retainers on the back of the it with Velcro strip. objects against sliding B with straps 3 or rear seat backrests for hanging carrier Store safety net in luggage compartment netting 3. bags on. Maximum load: 10 kg per below the floor covering. To open, remove retainer. the luggage compartment cover 3 3 55, lift floor covering at handle recess and tip forward 3 171. Position safety net at the front in the recesses. 58 Seats, Interior

z Close luggage compartment cover 3 z To calculate the EC kerb weight, enter 3 55. the data for your vehicle on page 3 226. z If the backrests are not folded down z The EC kerb weight includes allowances when transporting objects in the for the driver (68 kg), luggage (7 kg) and luggage compartment, they must be all fluids (tank 90 % full). 3 engaged in an upright position 55. z Optional equipment and accessories z Do not allow the load to protrude above increase the kerb weight. the upper edge of the backrests. z Weights and loads 3 226. z 3 The warning triangle and first-aid kit z Driving with a roof load increases the 3 (cushion) must always be freely sensitivity of the vehicle to cross-winds accessible. and has a detrimental effect on vehicle z Do not place any objects on the luggage handling due to the vehicle’s higher compartment cover 3 or the instrument centre of gravity. Distribute the load Picture no: 14110s.tif panel. evenly and secure it properly with Notes on loading the vehicle z No objects must be placed in the airbag retaining straps. Adjust the tyre pressure z Heavy objects in the luggage inflation area, since they could cause to the load conditions. Do not drive compartment should be placed as far injury when the systems are triggered. faster than 120 km/h. Check and re- tighten the straps frequently. Observe forward as possible against the properly z Items loaded must not prevent operation engaged rear seat backrests or, if the country-specific regulations. of the pedals, hand brake and gears or z rear seat backrests are folded down, obstruct the freedom of movement of The permissible roof load is 100 kg. The against the front seat backrests. If the driver. Do not place loose objects in roof load consists of the weight of the objects are to be stacked, the heavier the interior. roof rack plus the load carried. objects should be placed at the bottom. z Do not drive with luggage compartment z Secure heavy objects with lashing open when transporting bulky objects, 3 3 straps attached to lashing eyes 57. for example, since toxic exhaust fumes z When transporting objects with rear seat could penetrate the interior. backrests tilted forward, fit the safety net z The payload is the difference between 3 56. the permitted gross vehicle weight (see identification plate 3 218) and the EC kerb weight. Seats, Interior 59

Three-stage safety system Comprising: 9 Warning z three-point seat belts, The airbag systems serve to supplement the three-point seat belts and belt z belt tensioners at the front seats, tensioners. The seat belts must therefore z airbag systems for the driver and front always be worn. Disregard of these passenger seats 3 as well as the instructions may lead to injuries or outboard rear seats 3. endanger life. Vehicle passengers The three stages are activated in sequence should be informed accordingly. depending on the severity of the accident: Read the instructions supplied with the z The automatic seat belt locking devices child restraint system prevent the belt strap from being pulled out and thus ensure that the vehicle occupants are retained in their seats. Picture no: 18531s.tif z The front seat belts are pulled down at Three-point seat belts the belt buckles. This means the belts fit The seat belts have an automatic retractor, snugly, the occupants are decelerated so that the belt is spring tensioned and early with the vehicle and the body always lies against the body. loading is reduced. Information on correct seat position 3 45. z The airbag systems are also triggered in the event of severe accidents and form a The safety belts lock when the vehicle safety cushion for the occupants. accelerates or decelerates rapidly. This prevents the belt from extending and keeps the occupant in his or her seat. 60 Seats, Interior

Checking the seat belts 9 Warning From time to time, check operation of all seat belt system components and check for Fasten your seat belt before each trip. damage. Have damaged components In the event of an accident, persons not replaced. Have seat belts and deployed wearing seat belts endanger their fellow belt tensioners replaced by an authorised occupants and themselves. workshop after an accident.

Seat belt control indicator X 3 82. Make sure that seat belts are not damaged or trapped by sharp-edged objects. Seat belts are only intended for one person. They are not suitable for anyone under 12 years of age or under 150 cm tall. For children under the age of 12, we recommend the Opel child restraint system 3 65. Picture no: 14719s.tif Belt force limiters Belt tensioners In the front seats, stress on the body is The front safety belt systems tighten at the reduced by dampened release of the buckles in the event of a front or rear safety belt during a collision. collision above a specific degree of severity. This tensions the seat belts. Actuation of belt tensioners is indicated by illumination of control indicator v, see next column. Triggered belt tensioners must be replaced by a workshop. Belt tensioners can only be triggered once. Seats, Interior 61

z The belt tensioner and airbag system 9 Warning control electronics can be found in the centre console area. In order to avoid Have the cause of the fault remedied malfunctions, do not store magnetic immediately by a workshop. objects in this area. The system’s integrated self-diagnostics z When the rear seats are being used it allows faults to be quickly remedied. must be ensured that the components of the front seat belts are not damaged by Important shoes or other objects. Do not allow dirt z Do not affix or place accessories or other to penetrate the seat belt inertia reels. objects within the deployment zone of z We recommend that you have the seats the belt tensioners. Do not make any removed by a workshop. modifications to belt tensioner components as this will invalidate the z The belt tensioners only deploy once, vehicle type approval. which can be detected by illumination of Picture no: 17885s.tif the control indicator v. Have deployed Control indicator v for belt tensioners belt tensioners replaced by a workshop. The function of the belt tensioners and 9 Warning z The applicable safety regulations must airbag systems is monitored electronically Incorrect handling (e.g. removal or v be adhered to when the vehicle is and indicated via control indicator . fitting of seat belts or belt buckles) can disposed of. The vehicle should therefore When the ignition is turned on, the control cause the belt tensioners to deploy, with be disposed of by a recycling company. indicator comes on for about 4 seconds. risk of injury. If it does not light, does not go out after 4 seconds or comes on during driving, there is a fault in the belt tensioner or airbag systems 3 72.The systems may fail to deploy in the event of an accident. Deployment of the belt tensioners is indicated by continuous illumination of v. 62 Seats, Interior

Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body.

9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing.

Picture no: 14120s.tif Picture no: 14121s.tif Using the belts 9 Warning Fitting seat belts The seat belt must not be twisted and must On pregnant women in particular, the lie snugly against the body. The backrest lap belt must be positioned as low as must not be tilted back too far (maximum possible across the pelvis so as not to approx. 25 ). put too much pressure on the abdomen. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Pull the belt out of the reel, guide it across the body (making certain it is not twisted) and engage the latch plate in the buckle. Tension the lap belt frequently whilst driving by tugging the shoulder belt. Seats, Interior 63

Picture no: 14122s.tif Picture no: 14123s.tif Picture no: 14124S.tif Height adjustment Removing the belt Three-point seat belt on centre rear seat Adjusting the height of the upper To release seat belt, press red button on Pull latch plates out of belt retainer in roof. deflection point of the front seat belts: belt buckle. Click bottom latch plate into right-hand 1. Unreel seat belt a little. buckle (1) at middle seat. Remove top latch 2. Push button on sliding adjuster. plate from retainer, guide over shoulder and lap area with belt (do not twist) and 3. Set desired height. click into left buckle (2) at middle seat. 4. Allow sliding adjuster to audibly latch. If using the centre seat, both outboard Do not adjust height while driving. seats must be pushed backward and the backrests must be flush with the centre seat backrest 3 52. 64 Seats, Interior

Mounting clips 3 for ISOFIX child restraint systems The ISOFIX points for fitting a child seat are located between the seat backrest and the seat surface. Fasten permitted ISOFIX child restraint systems to the mounting brackets. Closely follow the installation instructions accompanying the ISOFIX child restraint system.

Picture no: 14739S.tif Picture no: 14740S.tif To remove the seat belt, press the button Insert in the seat belt holder in the roof with on the left buckle (2). If the centre seat is the lower latch plate pointing forward. lowered, press the button on the right buckle (1). The seat belt retracts automatically. Push the upper latch plate into the holder for the lower latch plate. Fold over locked together latch plates against the seat belt. Seats, Interior 65

3 Child restraint system Permissible options for fitting a child safety seat1) Follow the usage instructions for the child restraint system. Weight and On front On outboard seats in On centre age class2) passenger seat the rear seats rear seat Always comply with local or national regulations. In some countries, the use of Group 0: child restraint systems is forbidden on up to 10 kg certain seats. or approx. 10 months 1 Selecting the right system B , + U, + U, ++ Your child should be transported facing the Group 0+: rear in the vehicle for as long as possible. up to 13 kg The very weak cervical vertebrae of a child or approx. will be under less stress in an accident if 2years your child is facing the rear and semi- Group I: horizontal, than when he is sitting upright. 9to18 kg B2, + U, + U, ++ or approx. 9 Warning 8months Child restraint systems must not be to 4 years carried on a passenger’s lap. Danger Group II: to life. 15 to 25 kg or approx. 3 to 7 years X U U, ++ Group III: 22 to 36 kg or approx. 6 to 12 years

1) For reasons of safety, we recommend that the child safety seat be installed on one of the outer rear seats. 2) We recommend the use of each system until the child reaches the upper weight limit. 66 Seats, Interior

B1 = Conditional, without front + = Vehicle seat available with ISOFIX Note passenger airbags or with seat fixings. When using ISOFIX, only z Children under 12 years or under 150 cm occupancy recognition and Opel ISOFIX child restraint systems tall should only travel in an appropriate child restraint systems with approved for the vehicle may be child restraint system. transponders. used. z When transporting children, use the child The front passenger seat must also ++ = Only if both outboard seats are restraint systems suitable for the child’s have a height adjusting facility: pushed back and flush with the weight. move to highest position, slide front centre seat. z Ensure correct installation of child passenger seat all the way back and X = No child restraint system permitted restraint system, see the instructions move front passenger seat belt in this weight class. enclosed with the system. anchorage point to lowest possible z The covers of the Opel child restraint position. system can be wiped clean. B2 = Conditional, without side airbag, of z Do not stick anything on the child front passenger seat has been slid restraint systems and do not cover them all the way back, or with seat with any other materials. occupancy recognition and Opel child restraint systems with z Only allow children to enter and exit at transponders. the side facing away from the traffic. The front passenger seat must also z A child restraint system which has been have a height adjusting facility: subjected to stress in an accident must move to highest position and slide be replaced. front passenger seat all the way z Secure or remove child restraint systems back so that the seat belt runs that are in the vehicle but not in use. towards the front from the anchorage point. U = Universal suitability in conjunction with three-point seat belt. Seats, Interior 67

Exception: Passenger seat with a seat occupancy recognition system 3. The occupancy recognition system deactivates the front and side airbags for the passenger when the seat is unoccupied or an Opel child restraint system with transponders 3 is fitted to the passenger seat. Seat occupancy recognition 3 72. Opel child restraint system with transponders 3 3 73. Examples of events triggering the front airbag system: z Impact against a non-yielding obstacle: the front airbags are triggered at low Picture no: 16424s.tif Picture no: 14317s.tif vehicle speed. Airbag system z seat occupancy recognition 3, z Impact against a yielding obstacle (such Front airbag z the control indicator for Opel child as another vehicle): the front airbags are The front airbag system consists of one restraint systems y with transponders 3 only triggered at a higher vehicle speed. airbag in the steering wheel and one in the in the courtesy lamp. instrument panel. These can be identified The front airbag system will be triggered: by the word AIRBAG. z depending on the severity of the The front airbag system comprises: accident, z an airbag with inflator in the steering z depending on the type of impact, wheel and a second one in the instrument panel 3, z within the range shown in the illustration, z the control electronics with impact z independently of the side airbag sensor, system 3 and curtain airbag system 3. z the control indicator for airbag The ignition must be switched on. systems v in the instrument, 68 Seats, Interior

Picture no: 14125s.tif Picture no: 18530s.tif Picture no: 18531s.tif When triggered, the front airbags inflate in The front airbag system will not be milliseconds to form a safety cushion for 9 Warning triggered in the event of the driver and front passenger. The Optimum protection is only provided z the ignition is switched off, forward movement of the front seat with the seat in the proper position 3 45. occupants is checked, thereby z minor frontal collisions, Keep the area in which the airbag substantially reducing the risk of injury to z accidents in which the vehicle overturns, the upper body and head. inflates clear of obstructions. Wear the three-point seat belt properly z collisions involving a side or rear impact, No impairment of view will occur, because fastened. The front airbag system is an the airbags inflate and deflate so quickly that is to say, if it would not be of benefit to additional safety device, not a the occupants. that it is often not even noticed in an replacement for your seat belt. accident. Seats, Interior 69

In addition, the front airbag system will not be triggered for the front passenger in versions with seat occupancy recognition 3 if z the front passenger seat is unoccupied, z or there is a properly mounted Opel child restraint system with transponders 3. Seat occupancy recognition 3 72. Opel child restraint system with transponders 3 3 73.

Picture no: 14741s.tif Picture no: 14318s.tif Side airbag 3 The side airbag system will be triggered: The side airbag system consists of an z depending on the severity of the airbag in each front seat backrest. This can accident, be identified by the word AIRBAG. z depending on the type of impact, The side airbag system comprises: z within the range shown in the illustration z an airbag with inflator in the back of the on the centre door pillar of the driver’s or driver’s and front passenger seat front passenger side, respectively z independently of the front airbag z the control electronics, system. z the side impact sensors, The ignition must be switched on. z the control indicator for airbag systems v in the instrument, z seat occupancy recognition 3, z the control indicator for Opel child restraint systems y with transponders 3 in the courtesy lamp. 70 Seats, Interior

Exception: Passenger seat with a seat occupancy 9 Warning recognition system 3. The occupancy recognition system deactivates the front Keep the area in which the airbag and side airbags for the passenger when inflates clear of obstructions. the seat is unoccupied or an Opel child restraint system with transponders 3 is The side airbags will not be triggered in the fitted to the passenger seat. Seat event of z occupancy recognition 3 72. Opel child the ignition is switched off, restraint system with transponders 3 3 73. z frontal collisions, z accidents in which the vehicle overturns, z collisions involving a rear impact, z collisions involving a side impact outside the passenger cell. Picture no: 14742s.tif When deployed, the side airbag inflates In addition, the side airbag system will not within milliseconds to form a safety cushion be triggered for the front passenger in for the driver or front passenger in the versions with seat occupancy recognition 3 respective front door area. This if substantially reduces the risk of injury to z the front passenger seat is unoccupied the upper body and pelvis in the event of a z or there is a properly mounted Opel child side-on collision. restraint system with transponders 3. Seat occupancy recognition 3 72. Opel child restraint system with transponders 3 3 73. Seats, Interior 71

Picture no: 14129s.tif Picture no: 14318s.tif Picture no: 14127s.tif Curtain airbag 3 The curtain airbag system will be triggered: When the curtain airbag is triggered it The curtain airbag system consists of an z depending on the severity of the inflates within milliseconds and provides a airbag in the roof frame on each side. This accident, safety barrier in the head area on the can be identified by the word AIRBAG on z depending on the type of impact, respective side of the vehicle. This reduces the roof pillar. the risk of injury to the head considerably in z within the range shown in the illustration case of a side impact. The curtain airbag system comprises: on the centre door pillar of the driver’s or z an airbag with inflator in the roof frame front passenger side, on the driver’s and front passenger side respectively, z together with the side airbag system, z the control electronics, z irrespective of seat occupancy recognition, z the side impact sensors, z independently of the front airbag z the control indicator for airbag system. systems v in the instrument. The ignition must be switched on. 72 Seats, Interior

9 Warning 9 Warning Keep the area in which the airbag Have the cause of the fault remedied inflates clear of obstructions. immediately by a workshop. The curtain airbags will not be triggered in The system’s integrated self-diagnostics the event of allows faults to be quickly remedied. z the ignition is switched off, Seat occupancy recognition 3 z frontal collisions, The seat occupancy recognition system z accidents in which the vehicle overturns, deactivates the front and side front passenger airbags if the front passenger z collisions involving a rear impact, seat is unoccupied or an Opel child z collisions involving a side impact outside restraint system with transponders 3 has the passenger cell. been fitted to the front passenger seat. The Picture no: 17885s.tif curtain airbag system 3 remains activated. Control indicator v for airbag systems The control indicator for seat occupancy The function of the airbag systems and recognition y is located in the courtesy seat occupancy recognition 3 is monitored lamp. If this control indicator y illuminates electronically and indicated via control for approx. 4 seconds after the ignition is indicator v. When the ignition is turned on, switched on, the vehicle is equipped with the control indicator comes on for seat occupancy recognition 3 73, about 4 seconds. If it does not light, does Fig. 12097 S. not go out after 4 seconds or comes on during driving, there is a fault in the airbag If an Opel child restraint system with transponders 3 is fitted, this control systems, the seat occupancy recognition y system 3 or the belt tensioners 3 61. The indicator lights permanently after the systems may fail to deploy in the event of ignition is switched on as soon as the an accident. system has detected the child restraint system. Only then may the child restraint Deployed airbags are indicated by system with transponders 3 be used on the continuous illumination of v. passenger seat. Seats, Interior 73

9 Warning Only Opel child restraint systems with transponders 3 should be fitted on the front passenger seats. Use of systems without transponders poses a risk of fatal injury. Opel child restraint systems with transponders 3 can be identified by a sticker or badge. Control indicator y for Opel child restraint systems with transponders 3 The presence of an Opel child restraint Picture no: 15844t.tif system with transponders 3 is indicated Picture no: 12097s.tif Vehicles with seat occupancy recognition after the ignition has been switched on by If the control indicator does not come on can be identified by the sticker on the front permanent illumination of the control while driving, the front and side airbags for passenger seat or on the side of the indicator y in the courtesy lamp, as soon the passenger are not de-activated and instrument panel. as the seat occupancy recognition system there is a risk of injury or death to the child. has detected the child restraint system. Opel child restraint systems with Fit child restraint systems on the rear seat. transponders 3 are detected Have the cause of the fault eliminated by a automatically when installed properly on workshop. the passenger seat. When these child If the child restraint system is not correctly restraint systems are used on the installed or the transponders are defective, passenger seat, the front and side airbag the indicator lamp will flash. Check for systems for the passenger seat are correct child restraint system installation. deactivated. The curtain airbag system For installation of child restraint system remains activated. Observe the control with transponders 3 – see instructions indicator y for seat occupancy provided with child restraint system. recognition 3 3 73. 74 Seats, Interior

If the control indicator flashes when the Important z Do not stick anything on the steering 3 child restraint system with transponders z Placing accessories and objects in the wheel, instrument panel, front seat is correctly fitted, there is a fault with risk of expansion region of the airbag systems backrests or roof frame in the vicinity of injury to the child. Fit child restraint systems is not permitted due to the risk of injury if the airbags, or on the front passenger’s on the rear seat. Have the cause of the the airbag is triggered. seat cushion, or cover any of those areas fault eliminated by a workshop. with other materials. z Do not place any objects between the z If no Opel child restraint system with airbag systems and the vehicle Use only a dry cloth or interior cleaner to 3 transponders is fitted, the control occupants; danger of injury. clean the steering wheel, instrument indicator must not light or flash as the panel, front seat backrests, roof frame passenger airbag systems would not 9 Warning and seat cushion of the front passenger deploy. Have the cause of the fault seat. Do not use any aggressive cleaning eliminated by a workshop. As with any other object, child restraint agents. systems must not be carried on a z Only protective covers which are 9 Warning passenger’s lap. Danger to life. approved for your vehicle with side airbag may be fitted on the front seats. If the Opel child restraint system with z Use the hooks in the roof frame only to When fitting the protective covers, make transponders 3 has been fitted hang up light articles of clothing or coat sure that the airbag units on the according to the instructions, the control hangers. Do not place any objects in the outboard sides of the front seat indicator for Opel restraint systems with pockets of the hanging items – risk of backrests are not covered. transponders must illuminate in the injury. courtesy lamp when the ignition is z The airbag systems are triggered z The airbag systems and belt tensioner switched on. independently of each other depending control electronics can be found in the on the severity of the accident and the If the control indicator does not come on centre console area. In order to avoid type of impact. The side airbag system 3 while driving, the passenger airbag malfunctions, do not store magnetic and the curtain airbag system 3 are systems are not de-activated and there objects in this area. is a risk of injury or death. In this case fit triggered together. child restraint systems on the rear seat. z Each airbag deploys once only. Have a Have the cause of the fault eliminated workshop replace deployed airbags by a workshop. immediately. Seats, Interior 75 z The speeds, directions of movement and z The applicable safety regulations must z When using an Opel child restraint deformation properties of the vehicles, be adhered to when the vehicle is system with transponders 3 on the front and the properties of the obstacle disposed of. The vehicle should therefore passenger seat, in order to prevent concerned, determine the severity of the be disposed of by a recycling company. malfunctions, no objects (e.g. plastic accident and triggering of the airbags. z Persons weighing less than 35 kg should sheet, stickers or heated mats) may be The degree of damage to your vehicle only travel on the rear seats. This does placed under the child restraint system. and the resulting repair costs alone are not apply to children who are travelling not indicative that the criteria for in child restraint systems with 9 Warning triggering of the airbags were met. transponders 3. Child restraint systems or other objects z Do not perform any alterations on the z In vehicles with seat occupancy must never be carried on the laps of components of the airbag system, as this recognition 3, do not place any heavy passengers; If carried in this way, child would render the vehicle unroadworthy. objects on the front passenger seat restraint systems with transponders 3 in otherwise the airbag systems for the vehicles with seat occupancy 9 Warning front passenger seat may be triggered in recognition 3 could lead to front If handled improperly the airbag the event of an accident. passenger airbag systems not being triggered in the event of an accident. systems can be triggered in an explosive z In vehicles with seat occupancy manner – risk of injury! recognition 3, to prevent malfunctions do not use protective covers or seat z We recommend having the steering cushions on the front passenger seat. wheel, the instrument panel, all panelling parts, the door seals, the handles and the seats removed by a workshop. 76 Seats, Interior

Use of child restraint systems 3 on the front passenger seat in vehicles with airbag systems 3, but without seat occupancy recognition 3

9 Warning Vehicles with front passenger airbag 3 without side airbag 3: Child seats facing the rear of the vehicle must not be installed on the front passenger seat, risk of fatal injury. Child seats facing the direction of travel (child seats for weight classes I, II and III, following pages) may be installed on the front passenger seat if the seat has been pushed back as far Picture no: 11704a.tif Picture no: 14791s.tif as it will go and the backrest has been Vehicles with front passenger airbag can adjusted such that the lap belt fits be recognised by the word AIRBAG above 9 Warning snugly. the glove compartment and by the sticker Vehicles with side airbag 3: No child on the instrument panel on the passenger restraint system 3 may be fitted on the side - see Fig. 11704 A. front passenger’s seat; risk of fatal injury. A vehicle with side airbags can be identified by the word AIRBAG on the outboard sides of the front seat backrests. Seat occupancy recognition 3 3 72. Seats, Interior 77

The seat occupancy recognition system detects Opel child restraint systems with transponders 3 and switches off the front and side airbag systems for the front passenger seat. The curtain airbag system remains activated. Seat occupancy recognition 3 72. Opel child restraint systems with transponders 3 can be identified by a sticker or badge.

Picture no: 15844t.tif Picture no: 12097s.tif Use of child restraint systems 3 on front Vehicles with seat occupancy recognition passenger seat in vehicles with airbag can also be recognised by control systems 3 and with seat occupancy indicator y. If control indicator y recognition 3 illuminates for approx. 4 seconds after the ignition is switched on, the vehicle is 9 Warning equipped with seat occupancy recognition 3 72. Only Opel child restraint systems with transponders 3 can be fitted on the front passenger seats. Use of systems without transponders poses a risk of fatal injury.

Vehicles with seat occupancy recognition are identified by a sticker on the lower panel of the front passenger seat – see Fig. above. 78 Seats, Interior

Caution Do not damage the socket by using unsuitable plugs. Do not exceed the maximum power consumption of 120 watts. Electrical accessories connected to the socket must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839, otherwise vehicle malfunctions may occur. Do not connect any current-delivering accessories, e.g. electrical charging Picture no: 14111s.tif Picture no: 16111s.tif devices or batteries. 3 3 Cigarette lighter Accessory sockets If the tyre repair set is 3 is in operation, no The cigarette lighter is behind the ashtray The accessory socket is behind the cover in consumers may be connected to the cover in the centre console. the centre console. Further accessory auxiliary socket. 3 The ashtray cover opens when pressed at sockets are located in the centre console the point indicated. in front of the rear seats and in the luggage compartment. Press cigarette lighter with ignition switched on. Switches off automatically Accessory sockets are operable when the when element is hot. Withdraw cigarette ignition is switched on. Use of the sockets lighter. while the engine is not running will drain the battery. Seats, Interior 79

Picture no: 14111s.tif Picture no: 16110s.tif Picture no: 14114s.tif Ashtrays To empty, grip both sides of the ashtray Rear ashtray 3 insert at the spots illustrated and pull The ashtray is in the rear centre console. Caution upwards. To open, pull ashtray towards the back of To be used only for ash and not for the vehicle. combustible rubbish. To empty: open the ashtray, press the spring (arrow) and pull out the ashtray. Ashtray, front The ashtray is behind a cover in the centre console. The cover opens when pressed at the point indicated. 80 Seats, Interior

Picture no: 17884s.tif Picture no: 11699s.tif Picture no: 14115s.tif Ashtray 3 Stowage compartments Glove compartment The ashtray can be put in the front or rear Stowage compartment 3 beneath To open, pull handle upwards. of the centre console or in the oddments passenger seat On the inside of the glove compartment 3 tray . Lift stowage compartment by grasping cover there is a pen holder. recessed edge and pull out. Maximum To use, open cover. The glove compartment should remain load: 1 kg. To close the stowage closed while driving. compartment, push it in and engage. Seats, Interior 81

Picture no: 11701s.tif Picture no: 18601s.tif Picture no: 14116s.tif Stowage compartment for glasses 3 Foldaway tables 3 Coin holder 3 On driver’s side: fold down to open. These are located in the front seat In the centre console. Do not store heavy objects in the stowage backrests. Sun visors compartment. Open by pulling upward until it engages. Use the sun visor to protect from glare by Fold away by pressing down past the pulling it down and swivelling it to the side. resistance point. The mirror covers in the sun visors should Do not place any heavy objects on the be closed while driving. table. 82 Instruments, Controls Instruments, Controls

Picture no: 17876s.tif Picture no: Control indicators ...... 82 Control indicators X 3 Instrument display...... 87 The control indicators described here are Seat belt Control indicator lights up red. Information display ...... 90 not present in all vehicles. The description Warning buzzers...... 100 applies to all instrument versions. This comes on after turning on the ignition Windscreen wipers...... 100 The colours of the control indicators mean: (with warning tone) until the seat belt is done up. z Red Danger, important reminder. Fasten seat belt 3 62. z Yellow Warning, information, fault. z Green Switch-on confirmation. B Adaptive headlamp 3 (AFL) z Blue Switch-on confirmation. Control indicator lights up and/or flashes yellow. Lamps Fault in system. Contact a workshop for assistance. Instruments, Controls 83

For vehicles with diesel engine, the diesel fuel filter may need to be drained of water 3 212. Flashes when the ignition is on Fault in the electronic immobiliser system; the engine cannot be started 3 27.

Z Exhaust emission Control indicator lights up and/or flashes yellow. It illuminates when the ignition is switched on and goes out shortly after the engine starts. Picture no: 18385s.tif Picture no: Flashes A Illuminates when the engine is running System converted to symmetrical dipped Engine electronics, transmission Fault in emission control system. The beam. electronics, immobiliser, diesel fuel filter 3 permissible emission limits may be Control indicator lights up and/or flashes exceeded. Contact a workshop for Control indicator B flashes for assistance immediately. approximately 4 seconds after the ignition yellow. is switched on as a reminder that the It illuminates for a few seconds when the If it flashes when the engine is running system has been converted 3 110. ignition is switched on. Fault that could lead to catalytic converter damage. Ease up on the throttle until the AFL 3 106. Illuminates when the engine is running flashing stops 3 143. Seek the immediate Fault in engine electronics or transmission assistance of a workshop. > electronics. Electronics switches to Fog lamps 3 emergency running program, fuel v Control indicator lights up green. consumption may increase and driveability Airbag systems 3, Belt tensioners This comes on when the front fog lamps of vehicle may be affected 3 143. If the Control indicator lights up red. fault is still there when the engine is started are switched on 3 103. Illuminates when the engine is running again, contact a workshop for assistance. Fault in zone of airbag system or belt tensioners 3 61, 3 72. 84 Instruments, Controls

O Turn signal lamps Control indicator flashes green. The control indicator flashes if a turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a direction indicator lamp or associated fuse. Change bulbs 3 185. Fuses 3 182.

C Main beam Control indicator lights up blue. Picture no: 17876s.tif Picture no: It is illuminated when main beam is on and I 3. Move out of the flow of traffic as quickly during headlamp flash 3 11, 3 102. Engine oil pressure as possible without impeding other Control indicator lights up red vehicles. j It illuminates when the ignition is switched 4. Switch off ignition. 3, start engine. on and goes out shortly after the engine Control indicator lights up yellow. starts. 9 Warning The engine can only be started if the foot Illuminates when the engine is running When the engine is off, considerably brake is depressed. If the foot brake is not more force is needed to brake and steer. depressed, the control indicator illuminates Caution 3 130. Do not remove key until vehicle has Engine lubrication may be interrupted. come to a standstill, otherwise the This may result in damage to the engine steering column lock could engage and/or locking of the drive wheels. unexpectedly.

1. Depress clutch. Contact a workshop for assistance. 2. Move gearshift lever to neutral, or with manual transmission automated 3 place selector lever in N. Instruments, Controls 85

Lights up when the hand brake is released when the fluid level for the brake or clutch systems is low 3 214.

9 Warning Stop. Do not continue your journey. Consult a workshop.

Flashes On vehicles with manual transmission automated 3, control indicator R flashes for a few seconds after the ignition is switched off when the hand brake has not been applied. Picture no: 18385s.tif Picture no: T p u Winter mode for manual transmission Alternator Anti-lock brake system automated 3 Control indicator lights up red. Control indicator lights up red. Control indicator lights up yellow. It illuminates when the ignition is switched Illuminates while driving Control indicator lights up when winter on and goes out shortly after the engine Fault in anti-lock braking system 3 152. program is enabled 3 132. starts. Illuminates when the engine is running S m Stop, switch off engine. Battery is not Engine oil level 3 Cruise control 3 charging. Contact a workshop Control indicator lights up yellow. Control indicator lights up green immediately. The engine oil level is checked This comes on when the system is switched automatically 3. on 3 148. R Brake system, clutch system Illuminates when the engine is running r Control indicator lights up or flashes red. Engine oil level too low. Check engine oil Fog tail lamp level and top up engine oil if necessary Illuminated Control indicator lights up yellow. 3 210. Illuminates when the ignition is switched on This comes on when the fog tail lamp is if the hand brake is applied 3 151. switched on 3 104. 86 Instruments, Controls

! Preheating system 3, Diesel particle filter 3 Control indicator lights up and/or flashes yellow. Illuminated Preheating activated. Only activates when outside temperatures are low. Flashes (in vehicles with diesel particle filter) Control indicator ! flashes if the filter requires cleaning and previous driving conditions did not permit automatic Picture no: 17876s.tif Picture no: cleaning. Continue driving and if possible 1) EPS Y do not allow engine speed to drop Electric power steering Fuel level below 2000 rpm. Control indicator lights up yellow. Control indicator lights up and/or flashes ! yellow. The control indicator goes off as soon Fault in electrical power steering. Vehicle as the self-cleaning operation is complete. can still be driven, but greater force is Lamps 3 required for steering. Contact a workshop Level in fuel tank too low. Diesel particle filter 144. immediately. Flashes Fuel level is used up, fuel immediately. v Electronic Stability Program (ESP®Plus) 3 Never let the tank run dry! Control indicator flashes or lights up Erratic fuel supply can cause catalytic yellow. converter to overheat 3 142. Flashing during driving Diesel engines: Bleed the fuel system after 3 System engages 146. running empty 3 165. Illuminates while driving Fault in system 3 146.

1) EPS = Electric Power Steering. Instruments, Controls 87

Picture no: 12097s.tif Picture no: 17879s.tif Picture no: y Instrument display Kilometre display Seat occupancy recognition 3 In some versions, the indicators of the If the ignition is off the mileage is displayed 3 67, 3 72. instruments briefly rotate to the end for approx. 15 seconds by briefly pressing position when the ignition is switched on. the reset knob. Tachometer Top line: Displays the engine rpm. Trip odometer Drive in a low engine speed range for each Displays the number of kilometres since the gear as much as possible. gauge was reset. To reset, hold the reset knob depressed for Caution a few seconds with the ignition on. If the pointer is in the warning zone, the Bottom line: maximum permitted engine speed is Odometer exceeded. Engine at risk. Records the number of kilometres. Speedometer Maintenance, Inspection system, 3 89, Speed display. 3 208. 88 Instruments, Controls

For physical reasons, the engine temperature gauge shows the coolant temperature only if the coolant level is adequate. During operation the system is pressurised. The temperature may therefore rise briefly to over 100 C.

Picture no: 17906s.tif Picture no: 17907s.tif Coolant temperature display Fuel gauge Coolant temperature display Fuel tank level display. Pointer in zone at = Engine operating If the fuel level is too low, a warning lamp left temperature not yet lights up Y. When the light flashes, refuel as reached. soon as possible. Pointer between = Normal operating Never run the tank dry! the zones temperature. Because of the fuel remaining in the tank, the amount of fuel required to fill the Pointer in zone at = Temperature too tank may be less than the specified tank right (warning high: Stop vehicle capacity. zone) and switch off engine. Danger to engine. Check coolant level immediately 3 213. Instruments, Controls 89

R Reverse gear. N Neutral. A Manual transmission automated automatic mode. 1-5 Manual mode, current gear in manual transmission automated. Automated manual transmission 3 3 129.

Picture no: 18602s.tif Picture no: 17878s.tif Service Display 3 Transmission display 3 When the InSP indicator in the odometer Display of current gear or mode with display comes on, make a service manual transmission automated 3. appointment with a workshop as soon as possible. Maintenance, Inspection system, 3 208. 90 Instruments, Controls

Some information appears in the display in an abbreviated form.

Ü Board Computer 19,5° 19:36 BC 1 All values 12:01 17,0°C BC 2 257.0 km Timer 1 FM 3 90,6MHz Ø40km/h REG AS RDS TP 31.0 Ltr. 8 Ø 7.0 Ltr./100km

Picture no: 17913s.tif Picture no: 16719t.tif Information display Graphical information display 3, Colour Triple information display 3 information display 3 Display of time, outside temperature and Display of time, outside temperature and date/infotainment system (when it is on). date/infotainment system (when it is on). When the ignition is off, the time, date and The colour information display presents the outside temperature can be shown by information in colour. briefly pressing one of the two buttons next The type of information and how it is to the display. displayed depend on the equipment of the vehicle and the settings made. Instruments, Controls 91

9 Warning Caution: The road surface may already be icy even though the display indicates a few degrees above 0 C. : ,5°C 8:56 -5 Slippery road 07.04.2004 -2,5°C

OK

Picture no: 17913s.tif Picture no: 16707t.tif Outside temperature In vehicles with graphical information A fall in temperature is indicated display 3 or colour information display 3, a immediately and a rise in temperature warning message Slippery road appears after a time delay. on the display as a warning for icy road surfaces. There is no message below -5 If outside temperature drops below 3 C, C. the symbol : appears in the triple information display as a warning for icy road conditions. When temperature increases to at least 5 C, the : symbol goes out. 92 Instruments, Controls

Automatic time synchronisation 3 The RDS signal of most VHF transmitters automatically sets the time. This can be identified by } in the display. Some transmitters do not send a correct FM AS [TP] REG CDin MP3 time signal. In such cases, we recommend 8:56 5,5°C that you switch off automatic time ᕃ synchronisation. 90.6 MHz 07.04.2004 Activate setting mode and set it to year setting. Hold the Ö button depressed } about 3 seconds until flashes in the 19,5° 19:36 display and “RDS TIME" appears. The function is activated (RDS TIME 1) or deactivated (RDS TIME 0) with the ; Picture no: 17914s.tif button. Exit setting mode using the Ö Picture no: 16711t.tif Triple information display button. Graphical information display 3 Set date and time or colour information display 3, The infotainment system 3 must be off. selecting functions Activate setting mode by holding the Ö Functions and their menus are depicted in button depressed for about 2 seconds. The the graphical information display and flashing value is adjusted using the ; colour information display. button. The Ö button is used to switch to the next unit and to exit setting mode. These functions are marked or executed in the menu display via the cross switch, the multifunction knob 3 on the Infotainment System or buttons 3 on the steering wheel. Instruments, Controls 93

Picture no: 15593t.tif Picture no: 15559t.tif Picture no: 14034s.tif To select with four-way button Selection with the multifunction knob 3 Selection using buttons 3 on steering Select menu items via menus and with the Turn the multifunction button to highlight wheel buttons/four-way button of the menu items or commands and to select Select menu options via menus and with Infotainment system. function areas. the buttons. Press the multifunction button to select the highlighted item or confirm a command. To exit a menu, turn the multifunction button left or right to Return or Main and select. 94 Instruments, Controls

7 Settings 19,5° 19:36 7 Time, Date 19,5° 19:36

FM AS [TP] REG CDin MP3 Time, Date 19:36 Time 19:36 Language ᕃ 90.6 MHz Units 10 . 07 . 2004 Date 10 . 07 . 2004 Contrast

Day / Night 6 Synchron. clock automatical. 19,5° 19:36 6 Ign. logic

Picture no: 16711t.tif Picture no: 16712t.tif Picture no: 16713t.tif Function areas System settings Setting date and time 3 For each functional area there is a main The settings are accessed via the Select menu item Time, Date, from the page (Main), which is selected at the top Settings menu. Settings menu. edge of the display (not with the Press the Main button 3 (not found on all The menu for Time, Date is displayed. Infotainment system CD 30 or the Mobile infotainment systems) on the infotainment Phone Portal): Select the required menu item and make system (call up main display). setting. z Audio. Press the Settings button of the z 3 Navigation . infotainment system. On Infotainment z 3 Telephone . System CD 30, make sure no menu has z 3 Trip computer . been selected. 3 3 For Audio, Navigation and Telephone The Settings menu is displayed. functions – see infotainment system instructions. Instruments, Controls 95

Automatic time synchronisation 3 The RDS signal of most VHF transmitters automatically sets the time. 7 13 Languages 19,5° 19:36 Some transmitters do not send a correct 7 Settings 19,5° 19:36 time signal. In such cases, we recommend Time, Date X Deutsch that you switch off automatic time Language Deutsch English synchronisation. Units English Español On infotainment systems with navigation 3, time and date are also Contrast Español Nederlands harmonised upon receipt of a GPS satellite Day / Night Nederlands Français signal. 6 Ign. logic Français Italiano The function is activated by ticking the field in front of Synchron. clock automatical. in the Time, Date menu. Picture no: 16714t.tif Picture no: 16715t.tif Language selection Select the desired language. You can select the display language for Selections are indicated by a 6 in front of some functions. the menu item. Select menu item Language from the In systems with language version 3, when Settings menu. the language setting of the display is The available languages are displayed. changed, the system will ask if the message language should also be changed - see infotainment system instructions. 96 Instruments, Controls

Setting display mode 3 Display brightness is independent of vehicle lighting. Settings are made as 7 Settings 19,5°19:36 7 Contrast19,5° 19:36 follows: Time, Date Select menu item Day / Night from the Settings menu. Language ~ Europe-SI The options are displayed. Units | Japan 12 Contrast | Great Britain Automatic: adapted based on vehicle lighting. Day / Night | USA Always day design: black or coloured text 6 Ign. logic on light background. Always night design: white or coloured text on dark background. Picture no: 16716t.tif Picture no: 16717t.tif Setting units of measure Adjusting contrast 3 Selections are indicated by a o in front of Select menu item Units from the (graphical information display) the menu item. Settings menu. Select menu item Contrast from the Ignition logic 3 The available units are displayed. Settings menu. Adjustment, see Infotainment system instructions. Select the desired unit. The menu for Contrast is displayed. Selections are indicated by a o in front of Confirm the required setting. the menu item. Instruments, Controls 97

Ü Board Computer 19,5° 19:36 BC 1 All values

BC 2 Range 257 km 257.0 km Range Timer 1 Aver. Consump. 7.0 Ltr./100km Ø40km/h 33km Inst. Consumpt. 7.6 Ltr./100km 31.0 Ltr. 8 Ø 7.0 Ltr./100km 19,5° 19:36 OK

Picture no: 16719t.tif Picture no: 16710t.tif Picture no: 16718t.tif Graphical information display 3 Range If the fuel in the tank will allow less than or Colour information display 3, Range is calculated from current fuel tank 50 km of travel, the message Range Trip computer 3 content and instantaneous consumption. appears in the display. The display shows average values. The trip computers provide information on If the fuel in the tank will allow less than driving data, which is continually recorded After refuelling, the vehicle updates the 30 km of travel, the message and evaluated electronically. range automatically after a brief delay. Please refuel! 3 appears in the display. The trip computer main page provides Acknowledge warning message 3 92. information on range, average Instantaneous consumption consumption and momentary Display of current consumption. At low consumption 3. speeds, consumption per hour is displayed. To display the other trip computer driving information, press BC button on Infotainment system 3 or select trip computer menu on display. For vehicles with Infotainment System CD 30 3 and steering wheel remove control 3, the left steering wheel buttons only operate the trip computer. 98 Instruments, Controls

Distance travelled Display of distance travelled. The measurement can be reset at any time. Ü Ü Average speed Board Computer 19,5° 19:36 Reset BC 1 19,5° 19:36 Display of average speed. The BC 1 All values All values measurement can be reset at any time. BC 2 Stoppages in the journey with the ignition 257.0 km 257.0 km Timer 1 off are not included in the calculations. Ø40km/h Ø40km/h Effective consumption 31.0 Ltr. 31.0 Ltr. Display of fuel consumed. The 8 measurement can be reset at any time. Ø 7.0 Ltr./100km Ø 7.0 Ltr./100km Average consumption Display of average consumption. The measurement can be reset at any time. Picture no: 16719t.tif Picture no: 16720t.tif Restart trip computer The information of the two trip computers The measurement or calculation of the can be reset separately, making it possible following trip computer information can be to evaluate data from different time restarted: periods. z Distance, Select the required trip computer z Average speed, information and confirm. z Effective consumption, The value for the selected function will be reset and recalculated. z Average consumption. Select BC 1 or BC 2 from the trip computer menu. Instruments, Controls 99

The desired stop watch display can be selected from the Options menu 3: Ü Ü Driving Time excl. Stops Reset BC 1 19,5° 19:36 Board Computer 19,5° 19:36 The time the vehicle is in motion is All values BC 1 recorded. Stationary time is not included. BC 2 00:00:00 Driving Time incl. Stops 257.0 km Timer The time the vehicle is in motion is Ø40km/h recorded. The time the vehicle is stationary Start with the key in the ignition switch is 31.0 Ltr. Reset included. Ø 7.0 Ltr./100km Options Travel Time Measurement of the time from manual activation via Start to manual deactivation via Reset. Picture no: 16721t.tif Picture no: 16722t.tif To reset all information of a trip computer, Stop watch select menu item All values. Select menu item Timer from the Board After resetting, - - - is displayed for the Computer menu. selected trip computer information. The The Timer menu is displayed. recalculated values are displayed after a To start, select menu item Start. To stop, brief delay. select menu item Stop. Interruption of power supply To reset, select menu item Reset. If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. 100 Instruments, Controls

Warning buzzers Adjustable wipe interval 3 When starting the engine or whilst Setting wiper interval to a value between driving: 2 and 15 seconds: Stalk to timed interval z If seat belt is not fastened 3. wipe $, stalk to §, wait for desired interval, stalk back to timed interval z If the speed programmed at the wipe $. factory 3 is exceeded. The selected interval will remain stored z If the car has automated manual until the next time it is changed or until the transmission 3 and the driver’s door is ignition is switched off. opened when the engine is running, a gear is engaged and the foot brake is After turning on the ignition and setting the not depressed. lever to $, the interval is set to 7 seconds. When the vehicle is parked and the driver’s door is opened: z when the key is in the ignition switch Picture no: 14055h.tif z with parking lamps or dipped beam on Windscreen wipers z if the turn signal stalk is engaged Windscreen wipers To activate, press stalk briefly up & =Fast % =Slow $ = Adjustable timed interval wipe § =Off Instruments, Controls 101

Picture no: 14056h.tif Picture no: 14057h.tif Windscreen washer and headlamp Rear window washer and wiper system washer system 3 Push stalk forwards. The rear window wiper Pull stalk towards steering wheel. Screen wipes in timed interval mode. Switch off by wash is squirted onto the screen and the pulling stalk towards the steering wheel. wipers move back and forth a few times. If the stalk is held forwards, washer fluid is When the lights are switched on, sprayed on the rear window. windscreen wash is also squirted onto the headlamps. 102 Lighting

Model with daytime running lights 3 Lighting With ignition on and lights turned on 7, the dipped headlamps are on without instrument illumination. The daytime running lights switch off when the ignition is switched off. Follow the regulations of the country in which you are driving when using daytime running lights and fog lamps 3. Exterior lights ...... 102 Driving abroad 3 110. Main beam, headlamp flash ...... 103 Turn signal lamps ...... 103 Fog lamps > 3...... 103 Fog tail lamp r ...... 104 Picture no: 14756s.tif Reversing lamps...... 104 Exterior lights Hazard warning lamps ...... 104 Turn light switch: Headlamp range adjustment ?...... 104 Adaptive Forward Lighting 3 (AFL) .. 106 7 =Off Lead-me lighting 3 ...... 107 8 =Parking lamps Instrument illumination k, 9 =Dipped or main beam Information display illumination...... 108 In positions 8 and 9, the tail lamps and Courtesy lamp...... 108 number plate lamps are also on. Battery discharge protection 3...... 110 Misted light covers...... 110 If the ignition is switched off when main Headlamps when driving abroad ...... 110 beam or dipped beam is on, the parking lamps come on. Lighting 103

Picture no: 18475s.tif Picture no: 14054h.tif Picture no: 14758s.tif Main beam, headlamp flash Turn signal lamps Fog lamps > 3 Push stalk forward to switch from dipped Lever upwards = Right turn signal The fog lamps can only be switched on beam to main beam. Lever downwards = Left turn signal when both the ignition and lights are on. > To switch to dipped beam, press stalk If the stalk is moved past the resistance Operated with the button. forwards again. point, the turn signal lamp remains on. To operate the headlamp flash, pull stalk When the steering wheel moves back towards steering wheel. The main beam is toward the straight-ahead position, the switched on for as long as the stalk is held turn signal lamp is automatically in this position. deactivated. Brief flash: press stalk to perceptible resistance and release. Manual disconnection of turn signal lamps by returning to centre position. 104 Lighting

Fog tail lamp r The fog tail lamp can only be switched on both the ignition and dipped beam/parking lamps are on. Operated with the r button. The fog tail lamps on the vehicle are deactivated when towing a caravan/ trailer. Reversing lamps The reversing lamps come on when the ignition is on and reverse gear is engaged.

Picture no: 14303s.tif Picture no: 14757s.tif Hazard warning lamps Headlamp range adjustment ? Operated with the ¨ button. Manual headlamp range adjustment 3 To aid location of the pushbutton, the red To adapt headlamp range to the vehicle surface is illuminated when the ignition load so that fellow motorists are not switched on. When the button is pressed, blinded: Press knob to disengage and turn its control indicator flashes in time with the to required position. hazard warning lamps. Lighting 105

Settings. Automatic headlamp range 3 0 = Front seats occupied adjustment On vehicles with Xenon headlamps, 1 = All seats occupied headlamp range is adjusted automatically 2 = All seats occupied and luggage based on vehicle load. compartment load 3 = Driver’s seat occupied and luggage compartment load 106 Lighting

Picture no: 15209j.tif Picture no: Picture no: 17887s.tif Adaptive Forward Lighting 3 Cornering light Control indicator B for adaptive driving (AFL) An additional lamp comes on with lights ensures better illumination of certain steering wheel positions (after Illuminated: Fault in system. The system is not ready for operation. z bends (curve lighting), approx. 90 ), turn signal settings and speeds (up to approx. 40 km/h). Contact a workshop for assistance. z crossings and narrow bends (cornering light). The light is thrown approx. 90 to the After a power supply interruption the left or right of the car, to a distance of steering angle sensor must be calibrated to Curve lighting approx. 30 metres. make the system operational. 3 147 The light beam pivots based on Reversing function Control indicator B flashes for steering wheel position and speed (from about 4 seconds after the ignition is If the lights are on, reverse gear is approx. 10 km/h). switched on as a reminder that the engaged, and the turn signal is activated, headlamps have been converted, see The headlamps shine at an angle of up the cornering light on the appropriate side "Headlamps for driving abroad" 3 110. to 15 to the right or left of the direction of is switched on. The cornering light stays on travel. for 15 seconds once the turn signal has been switched off. Lighting 107

If the driver’s door is left open, the lamps will go out after two minutes. The light is switched off immediately by inserting the key into the ignition or pulling the turn signal stalk towards the steering wheel again.

Picture no: 14302s.tif Picture no: 17920S.tif Lead-me lighting 3 Lead-me lighting when opening the Lead-me lighting when leaving the vehicle 3 vehicle 3 The Lead-me-to-the-car lighting function The dipped headlamps come on for allows the dipped headlamps to be lit for around 30 seconds after switching on and around 30 seconds using the remote closing the driver’s door. control. To activate: This function must be activated (once): 1. Switch off ignition. Unlock the vehicle, put the key in the ignition and press the light switch for 2. Remove ignition key. approx. 5 seconds - see next page, 3. Open driver’s door. Fig. 14136 S. 4. Pull turn signal stalk toward steering To deactivate the function permanently, wheel. contact a workshop. 5. Close driver’s door. 108 Lighting

To activate the lead-me-to-the-car light function, press button q on the remote control twice with the vehicle locked. Country-specific version 3: to enable the lead-me-to-the-car function, press button q on the remote control once with the vehicle locked. The lead-me-to-the-car light function is deactivated immediately by pressing button p of the remote control or switching on the ignition.

Picture no: 14759s.tif Picture no: 14136s.tif Instrument illumination k, Courtesy lamp Information display illumination Automatic interior light Lights come on when ignition is switched on. Comes on automatically when the vehicle is unlocked with the radio remote control or Brightness can be adjusted when the when a door is opened. exterior lights are on: Push to release knob k and then turn it clockwise or Goes off automatically after a delay when anticlockwise and hold until the desired the doors are closed or immediately when brightness is obtained. the ignition is switched on or the doors are locked. Display mode 3 3 96. Front courtesy lamp To operate manually from inside when the doors are closed: on = Press light switch 0 off = Press light switch 0 again Lighting 109

Entry lighting 3 After unlocking the vehicle, the instrument and switch illumination plus the courtesy lamps come on for a few seconds. Illuminated mirror in the sun visors 3 The lighting switches on when the cover is opened. Glove compartment lighting 3 The glove compartment light comes on when the ignition is on and the lid is opened. Luggage compartment lighting 3 The luggage compartment light comes on when the tailgate is open. Picture no: 11607s.tif Picture no: 12344t.tif Front reading lamps 3 Courtesy lamps and rear reading lamps 3 Automatically regulated centre console Operate using buttons with the ignition Centre switch position: The rear courtesy lighting 3 switched on. lamp comes on together with the front one Spotlight in housing of interior mirror. when a door is opened. Daylight-dependent, automatically The rear reading lamps on the left and regulated centre console lighting with right can be switched on separately. With ignition switched on. ignition on: On = Switch position I Off = Switch position 0 110 Lighting

Battery discharge protection 3 To return to asymmetrical dipped beam, Some consumers such as the interior pull and hold the main beam stalk again, lighting switch themselves off after switch on the ignition and wait for the approx. 30 minutes if the ignition is off in acoustic signal. AFL control indicator B order to protect the battery charge. will then discontinue flashing. Control indicator B 3 106. Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help, switch on the lights. Headlamps when driving abroad The asymmetrical dipped beam increases Picture no: 14053h.tif the field of vision on the passenger side of Vehicles with Adaptive headlight 3 (AFL) the lane. 1. Pull stalk towards steering wheel and In countries where traffic drives on the hold. opposite side of the road, prevent glare as 2. Switch on ignition. follows. 3. After approx. 3 seconds, an acoustic Vehicles with halogen headlamp system signal sounds and then AFL control or Xenon headlamp system 3 indicator B flashes approx. 4 seconds. Have headlights converted in a workshop. After the switch, AFL control indicator B flashes for 4 seconds each time the ignition is switched on. Infotainment system 111

Infotainment system Radio reception 3 Radio reception may be disrupted by static, noise, distortion or loss of reception due to z changes in distance from the transmitter, z multi-path reception due to reflection and, z shadowing.

Radio reception 3...... 111 Infotainment system 3 Infotainment system 3...... 111 The infotainment system is operated as Steering wheel remote control 3...... 111 described in the operating instructions. Rear seat audio system 3...... 112 Picture no: 14034s.tif 3 AUX input 3...... 112 Steering wheel remote control Electronic data acquisition in toll The functions of the infotainment system 3 systems ...... 112 and the information display can be Mobile telephones and radio operated with the buttons on the steering equipment 3...... 113 wheel. Further information 3 93 and the infotainment system instructions. 112 Infotainment system

Picture no: 14035s.tif Picture no: 18473s.tif Picture no: 14033s.tif Rear seat audio system 3 AUX input 3 Electronic data acquisition in toll Twin Audio allows rear seat occupants the The AUX input is next to the handbrake in systems choice between the audio source played on the centre console. In vehicles with heat-reflecting 1) the infotainment system or a different An external audio source, e.g. a portable windscreen 3 Attach chipcard 3 for audio source. Only an audio source that is CD player, can be connected to the AUX electronic data acquisition and fee not currently active on the infotainment input via a 3.5 mm jack plug. payment in black area of windscreen on system can be controlled. left or right-hand side behind the interior Keep AUX input clean and dry at all times. Two headphone connections are available, mirror, see markings in figure. Attaching with separate volume controls. Further information in the infotainment the chipcard outside this area may cause system instructions. data acquisition malfunctions. Further information in the infotainment system instructions.

1) Solar Reflect. Infotainment system 113

Mobile telephones and radio Use of a handsfree attachment without equipment 3 external antenna with mobile telephone Caution standards GSM 900/1800/1900 and UMTS The Opel installation instructions and the Mobile phones and radio equipment is only permitted if the maximum operating guidelines provided by the may cause malfunctions in the vehicle transmission power of the mobile telephone manufacturer must be followed electronics if they are operated in the telephone is 2 watts for GSM 900 or 1 watt when fitting and operating a mobile vehicle without the external antenna for the other types. telephone. Failure to do so could invalidate unless the above-mentioned regulations the vehicle’s operating permit For reasons of safety, we recommend that are complied with. (EU Directive 95/54/EG). you do not use the phone while driving. Recommended prerequisites for fault-free Even use of a handsfree set can be a operation: distraction while driving. Be sure to observe z Professionally installed exterior antenna any country-specific regulations. to obtain the maximum range possible 9 Warning z Maximum transmission power 10 Watt Mobile phones that do not comply with z Installation of the telephone in a suitable the above-mentioned mobile phone spot (see information 3 74) standard and radio equipment must Seek advice on predetermined installation only be operated using an antenna that points for the external antenna or is attached to the exterior of the vehicle. equipment holder and ways of using devices with a transmission power exceeding 10 watts. We recommend you contact your Opel Service Partner who will have brackets and various different accessory kits available and can fit them correctly. 114 Climate control Climate control

Heating and ventilation system, air conditioning system 3 ...... 114 Electronic climate control system 3 ... 114 Air vents ...... 115 Picture no: 14154s.tif Picture no: 16499s.tif Heating and ventilation system ...... 116 Heating and ventilation system, Electronic climate control Air conditioning system 3...... 119 air conditioning system 3 system 3 Electronic climate control system 3 ... 122 Ventilation, heating and cooling 3 are Offers the greatest comfort in the vehicle Auxiliary heater ...... 127 combined into one unit that is designed to interior regardless of the conditions Air intake...... 127 provide comfort regardless of the season, outside. weather or outside temperature. Air outlet...... 127 To ensure a uniform and comfortable Pollen filter ...... 127 When cooling 3 is activated, the air is climate in the vehicle, the temperature of Regular operation ...... 128 cooled and dried. inflowing air, air-flow rate and air The heating unit heats the air as required in distribution are automatically adapted all operating modes depending on the based on the climate conditions outside position of the temperature switch. The air the vehicle and the current temperature of supply can be adjusted to suit the vehicle interior. requirements by means of the fan. Electronic climate control system 3 3 122. The buttons for cooling n and air recirculation 4 are only found on versions with optional air conditioning system 3. Air conditioning system 3 3 119. Climate control 115

Windscreen defroster nozzles (2) Air distribution switch set to V or J: Air is directed onto the windscreen and door windows. Additional vents are beneath the windscreen and side windows and in the front footwell.

Picture no: 16112s.tif Picture no: 14576s.tif Air vents Centre and side (1) air vents At least one air vent must be open while To open vent: rotate wheel upwards. cooling 3 (air conditioning compressor) is Adjust the direction of air flow by rotating on in order to prevent the evaporator from the horizontal and vertical wheels. icing up due to lack of air movement. To close the vents rotate the wheel fully Pleasant ventilation to the head area downwards. controlled by the position of the temperature switch. To increase the air supply, set the fan to a higher speed and set the air distribution switch to M or L. 116 Climate control

Picture no: 14144s.tif Picture no: 14145s.tif Picture no: 14146s.tif Heating and ventilation system Air flow Air distribution Temperature Adjusted using centre rotary switch. Set using right rotary switch. Adjusted using left-hand rotary switch. x off V to windscreen and front side red area = warm 1-4 selected fan speed windows J blue area = cold The rate of air flow is determined by the towards windscreen, front door fan. The fan should therefore also be windows and footwell The amount of heat is dependent on the K to footwell coolant temperature and is thus not fully switched on during a journey. L towards head area and footwell attained until the engine is warm. M towards head area Open the air vents when the switch is set to L or M. Climate control 117

Heating The comfort and general well-being of the For rapid warming of the passenger vehicle occupants are to a large extent compartment: dependent on a suitable ventilation and z Turn the temperature switch clockwise as heating setting. far as it will go (warm). To achieve stratification of temperature z Set the fan to speed 3. with a pleasant "cool head and warm feet" effect, set the rotary air distribution switch z Set air distribution switch to desired to K, J or L, set temperature rotary position, preferably position J, 3 116. switch to any position (in centre range with temperature stratification effect).

Picture no: 14150s.tif Ventilation z Set the temperature to the desired setting. z Switch fan on, select fan setting according to requirements. z For maximum ventilation in head area: set air distribution switch to M and open all vents. z For ventilation to foot well: Set air distribution switch to K. z For simultaneous ventilation to the head area and the foot well: Set air distribution switch to L. 118 Climate control

z Set fan to 3 or 4. z Set air distribution switch to V. z Switch on heated rear window Ü 3. z Open side air vents as required and direct them towards door windows. z For simultaneous footwell heating, set air distribution switch to J.

Picture no: 14151s.tif Picture no: 16481s.tif Heating the foot well Demisting and defrosting windows z Set the temperature switch in the right- hand zone. 9 Warning z Switch on fan. Disregard of the instructions could lead z Set air distribution switch to K. to misting or icing of the windows and subsequent accidents due to impaired visibility.

Misted or icy windows, e. g. due to damp weather, damp clothing or low outside temperatures: z Turn the temperature switch clockwise as far as it will go (warm). Climate control 119

Air conditioning system 3 As a supplement to the heating and ventilation system, the air conditioning system cools and dehumidifies (dries) inflowing air. If cooling or dehumidification is not desired, switch off cooling in order to save fuel. Cooling switches off automatically at low outside temperatures.

Picture no: 14159s.tif Picture no: 14158s.tif Cooling n Air recirculation system 4 Only operate with the engine and fan The air recirculation mode of the running. Activate and deactivate with ventilation system is activated and the n button. deactivated by pressing the 4 button. When cooling is active (AC compressor) the If fumes or unpleasant odours penetrate air is cooled and dehumidified. If cooling or from outside: Temporarily switch on air dehumidification is not desired, switch off recirculation system 4. cooling in order to save fuel. To increase cooling at high outside Cooling switches off automatically at low temperatures, switch on the air outside temperatures. recirculation system briefly. When cooling operates, condensation forms and drips from the underside of the vehicle. 120 Climate control

Temperature switch in centre of 9 Warning adjustment range: warmer air will flow into the foot well and cooler air into the upper The air recirculation system minimises zone, with warmer air coming from the side the entry of outside air. The humidity air vents and cooler air from the centre increases, and the windows can mist up. vents. The quality of the passenger compartment air deteriorates which may cause the vehicle occupants to feel drowsy. Air distribution to V: the air recirculation system is automatically switched off to speed up window demisting and prevent fogging. Picture no: 14160s.tif Comfort setting z Set cooling n as desired. z Air recirculation system 4 off. z Set temperature switch as desired. z Switch on fan at desired speed. z Set air distribution switch to M or L. z Open or adjust vents as required. Climate control 121

z Cooling n on, the air conditioning compressor automatically switches itself off at low outside temperatures (icing). z Turn the temperature switch clockwise. z Set fan to 3 or 4. z Air distribution switch to V, air recirculation system 4 automatically switches off, – or – if there is still moisture in the system after previous air conditioning operation, the windows may mist up. To prevent this, set air distribution to K before starting Picture no: 14162s.tif Picture no: 16482s.tif engine and set to V approx. 5 seconds Maximum cooling Demisting and defrosting windows after starting. Briefly open windows, sun roof and tilting roof 3 so that warm air can escape quickly. 9 Warning z Activate heated rear window Ü. z Cooling n on z Open side air vents as required and Disregard of the instructions could lead direct them towards the side windows. z Air recirculation system 4 on to misting or icing of the windows and subsequent accidents due to impaired z Turn the temperature switch visibility. anticlockwise as far as it will go (cold) z Set fan to 4 Misted or icy windows, e. g. due to damp weather, damp clothing or low outside z M Set air distribution switch to temperatures: z Open all air vents 122 Climate control

Electronic climate control system 3 Provides a the greatest amount of comfort in the interior regardless of the weather, outside temperature or season. To ensure a constant and comfortable climate in the vehicle, the temperature of the inflowing air, the air-flow rate and the air distribution are changed automatically according to climatic conditions outside the vehicle. The climate is regulated automatically based on personal settings. Picture no: 16500s.tif Picture no: Temperature changes due to external When set to automatic mode, the climate influences, such as direct sunlight, are control system provides the optimal automatically compensated. settings for almost all conditions. If When cooling (air conditioning necessary, climate control system settings compressor) is active, air is cooled and can be modified manually. dehumidified. The climate control system is only The pollen filter removes dust, soot, pollen operational when the engine is running. and spores from the inflowing outside air. If you wish the climate control system 3 to operate correctly, do not cover the sensor on the instrument panel. Cooling (air conditioning compressor) switches off automatically at low outside temperatures. Climate control 123

Switching off the air conditioning Temperature preset compressor (ECO appears in display) can The left rotary knob can be used to set the have a detrimental effect on comfort and temperature to values of between 16 C safety 3 125. and 28 C. All air vents are actuated automatically in For the sake of comfort, only change the automatic mode. The air vents should pre-selected temperature in small steps. 3 therefore always be open 115. If the temperature setting is less than 16 C, LO appears in the air conditioning display: the climate control system runs constantly at maximum cooling power, and the temperature is not regulated. If the temperature setting is above 28 C, HI appears in the air Picture no: 16496s.tif conditioning display: the climate control Automatic mode system runs constantly at maximum Basic setting for maximum comfort: heating power, and the temperature is not z Press AUTO button. regulated. z Open all air vents. The temperature settings remain stored z Switch on AC compressor 3 125. when the ignition is turned off. z Preset temperature to 22 C with turn knob. The temperature can be set higher or lower as desired. 124 Climate control

Manual settings Temperature, air distribution and blower Under certain circumstances (e.g. iced or are set automatically. misted windows), the functions of the To return to automatic mode: press climate control system can be modified button V or AUTO. manually. Heated rear window 3 41. Manual settings are saved when the ignition is switched off. Make manual settings as follows when necessary:

Picture no: 16501s.tif Window demisting and defrosting

9 Warning Disregard of the instructions could lead to misting or icing of the windows and subsequent accidents due to impaired visibility.

Misted or icy windows, e. g. due to damp weather, damp clothing or low outside temperatures: Press button V, V appears in the air conditioning display. Climate control 125

Picture no: 16503s.tif Picture no: 16504s.tif Picture no: 16505s.tif Activating and deactivating air Air distribution Air flow conditioning compressor Press one or more of the following buttons. Set air flow using the right-hand rotary Press the ECO button. ECO appears in the The corresponding symbol appears in the knob. The selected fan speed is indicated air conditioning display. air conditioning display: by the number of bars. Switch on to save fuel. In this mode cooling s Air distribution towards windscreen To deactivate the fan and thereby the (AC compressor) is switched off. and front door windows. automatic climate control system: Turn the Inflowing air is neither cooled nor M Air distribution towards vehicle right-hand rotary knob anticlockwise until dehumidified. This restricts the level of occupants via adjustable vents. the display goes out. comfort provided by the automatic climate K Air distribution towards footwell. Switching on: turn rotary knob clockwise. control system. This may cause the To return to automatic mode: Press the To return to automatic mode: Press windows to mist up, for example. appropriate buttons again, or press AUTO. AUTO button. When cooling operates, condensation forms and drips from the underside of the vehicle. To return to cooling operation: press ECO button. ECO goes out. 126 Climate control

Press button 4, % appears in the air conditioning display.

9 Warning The exchange of fresh air is reduced in air circulation mode. The quality of the passenger compartment air deteriorates which may cause the vehicle occupants to feel drowsy. In operation without cooling the air humidity increases, so the windows may mist up. Consequently, the air circulation system should only be run for short periods of time. Picture no: 16506s.tif Picture no: 16507s.tif Manual air recirculation mode To switch off manual air circulation: press Air conditioning with the engine not The air recirculation system prevents the button 4 again. running entry of outside air and the air in the When the vehicle is stopped and the passenger compartment is circulated. ignition off, the residual heat or cooling in the system can be used for climate control in passenger compartment, e.g. when stopped at a level crossing. Press AUTO with the ignition off. The preselected temperature appears in the air conditioning display. The temperature can be adjusted with the left-hand rotary knob. Residual climate control can only operate for a limited period of time. To cancel, press the AUTO button. Climate control 127

Auxiliary heater Pollen filter Depending on outside temperature and The pollen filter cleans dust, soot, pollen engine temperature, the passenger and spores from the air entering from compartment of vehicles with Quickheat 3 outside. The active carbon layer 3 electric auxiliary heating is warmed up eliminates most odours and noxious more quickly. environmental gases from the air. Diesel-engined vehicles have a fuel- powered auxiliary heater 3.

Picture no: 14147s.tif Air intake The air intakes in front of the windscreen on the far right and left sides of the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow. Air outlet Do not cover the air outlets when storing items in the luggage compartment storage compartments. 128 Climate control

Regular operation Service For consistently good operation, the air For optimal cooling performance, we cooling system 3 must be switched on for recommend that the climate control several minutes once per month regardless system be checked annually, starting three of the weather and the time of year. years after initial vehicle registration. Operation not possible with the cooling z Functionality and pressure test, system switched on and when the outside temperature is low. z Heating functionality, z Leakage check, z Check of drive belts, z Cleaning of condenser and evaporator drainage, z Performance check. Driving and operation 129

Driving and operation Manual transmission automated 3 The manual transmission automated transmission 3 permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control.

Manual transmission automated 3 ... 129 Manual transmission ...... 134 Driving hints ...... 135 Saving fuel, protecting the Picture no: 17878s.tif environment ...... 137 Transmission display Shows the mode and current gear. Fuels, refuelling...... 139 Catalytic converter, exhaust gasses .. 142 If the Winter programme is activated, T is Drive Control Systems ...... 146 illuminated. Hydraulic brake system ...... 151 Anti-lock brake system (ABS u)...... 152 Hand brake...... 153 Brake assist ...... 153 Hill Start Assist 3 (HSA) ...... 153 Wheels, tyres...... 153 Roof rack 3 ...... 158 Towing equipment 3...... 158 Towing equipment with removable ball bar 3 ...... 159 Caravan/trailer towing...... 162 130 Driving and operation

Selector lever in o (centre position) Once the selector lever has been moved from N to position o (centre position) with the foot brake operated, the Easytronic is in automatic mode and first gear has been selected (second gear with winter programme enabled). "A" appears in the transmission display. When the foot brake is released the vehicle starts to "creep". If the foot brake is not operated, "A" flashes. Start off by pressing the accelerator immediately or more selector lever back to N and repeat procedure with foot brake operated. Picture no: 18386s.tif Picture no: 14175s.tif In Automatic mode, selection of other Starting the engine Operation of manual transmission gears is automatic irrespective of driving When starting the engine, activate the automated using selector lever conditions. footbrake at the same time. The engine Always move the selector lever all the way can only be started in position N and with to the stop. Note the gear or mode the footbrake activated. The transmission indicator in the transmission display. display shows "N". If the footbrake is not Move selector lever toward N j 3 activated, the control light in the Neutral. instrument panel illuminates and "N" flashes in the transmission display, the engine cannot be started. If no brake lights are operational, the engine will not start. Driving and operation 131

Selector lever in + or - Stopping the vehicle + Shift to a higher gear. In Automatic or Manual mode, when the - Shift to a lower gear. vehicle has stopped first gear (with Winter mode engaged, second gear) is engaged If a higher gear is selected when the automatically and the clutch released. In R running speed is too low, or a lower gear reverse remains engaged. when the speed is too high, the gear If a warning signal sounds when the selection will not take place. This prevents driver’s door is opened (foot brake not the engine from running at too low or too depressed), move the selector lever to N high revs. and apply the hand brake. Gears can be skipped by jogging the When stopping on gradients, engage the selector lever repeatedly at short intervals. hand brake or depress the brake pedal. To When the vehicle is in automatic mode, the prevent overheating of the clutch, do not manual transmission automated shifts to increase engine speed to ensure smooth Picture no: 14175s.tif manual mode by moving the selector lever idling when in gear. Selector lever in A/M to position or . The correct gear is + - Switch off engine if stopping for a lengthy Switch between Automatic and Manual indicated on the transmission display. period, e.g. in traffic jams or at level mode. Selector lever in R crossings. In manual mode, gears can be selected Reverse gear. Engage only when vehicle is Electronically controlled driving manually by moving the selector lever stationary. programmes in automatic mode to or . The currect gear is indicated in + - Press button on selector lever, select R. The z Following a cold start, the operating the transmission display. transmission display shows "R". temperature program automatically If the engine speed is too low the manual If R is selected when the vehicle is in motion, increases the engine revolutions to bring transmission automated will automatically "R" flashes in the transmission display and the catalytic converter to the required shift to a lower gear even in Manual mode. no gear is engaged. temperature. This prevents the engine from stalling. z The adaptive program automatically selects the gear according to the driving conditions, e.g. increased load and gradients. 132 Driving and operation

Engine braking Automatic mode: When driving downhill, the manual transmission automated does not shift into higher gears until a fairly high engine speed has been reached. When braking, the manual transmission automated shifts down in good time. Manual mode: To utilise the engine braking effect, select a lower gear in good time when driving downhill. "Rocking the car" The selector lever should only be moved Picture no: 17889s.tif Picture no: 13322a.tif between o (centre position) and R Winter programme T Kickdown repeatedly if it becomes necessary to rock In the event of difficulties starting off on If the accelerator pedal is pressed past the the vehicle to free it from sand, mud, snow slippery roads, press button T ("A" and T pressure point, the transmission shifts to a or a hole. Do not race the engine and avoid appear on the transmission display). The lower gear depending on engine speed. sudden acceleration. manual transmission automated switches During kickdown no manual gear shifting is to automatic mode and the vehicle sets off possible. in second gear. When the engine speed approaches its The Winter programme is switched off by: upper limit, the transmission shifts to a z pressing the T button again. higher gear during kickdown even in z turning off the ignition. Manual mode. z switching to Manual mode. Without kickdown this automatic shift is not effected in Manual mode. z when clutch temperature is too high. Driving and operation 133

Vehicle storage Apply the handbrake and remove the key from the ignition. The most recently engaged gear (indicator in transmission display) remains engaged. With N, no gear is engaged. When the ignition is switched off the manual transmission automated no longer responds to movement of the selector lever. If the ignition key is not removed, the battery may be discharged if the vehicle is then left to stand for a lengthy period of time. Picture no: 14083j.tif If the hand brake has not been applied, the Picture no: 17890s.tif Manoeuvring the vehicle Fault control indicator R flashes for a few For accurate manoeuvring when parking, To prevent damage to the automated seconds after the ignition is switched off. at garage entrances etc., the creeping manual transmission, the clutch is closed movement can be utilised by releasing the automatically at high clutch temperatures. foot brake with a gear selected. Warning light A lights up if there is a fault. Never actuate accelerator and brake It is possible to continue driving but manual pedals simultaneously. mode can no longer be used for changing To prevent damage, the manual gear. transmission automated deactivates the If "F" also appears in the transmission "creep function" when the temperature of display, it is not possible to continue the automatic clutch is extremely high. driving. Have cause of fault remedied by a workshop. The system’s integrated self diagnostics allow faults to be quickly remedied. 134 Driving and operation

3. Clean transmission around the cap (see Fig.) so that no dirt can get into the opening when the cap is removed. 4. Rotate cap to slacken and remove by lifting upwards – see figure. 5. Turn the adjusting screw clockwise using a flathead screwdriver (vehicle tools 3 3 171) until clear resistance can be felt. The clutch has now been disengaged.

Caution Do not turn beyond the resistance, since this can damage the Easytronic.

Picture no: 14721s.tif 6. Fit cleaned cap again. The cap must be Picture no: 15270s.tif Interruption of power supply in full contact with the housing. Manual transmission The clutch is not disengaged if there is an To engage reverse, with the vehicle interruption of the power supply when a Caution stationary wait 3 seconds after declutching gear is engaged. The vehicle cannot move. and then pull up the button on the selector If the battery is flat, start the car using Towing the vehicle and starting the lever and engage the gear. jump leads 3 166. engine is not permitted when the clutch has been released in this way, although If the gear does not engage, set the lever in If the cause is not a flat battery, contact a the vehicle can be moved a short neutral, release the clutch pedal and workshop for assistance. If the vehicle has distance. depress again; then repeat gear selection. to be moved out of flowing traffic, Do not grind the clutch unnecessarily. disengage clutch. Contact a workshop for assistance immediately. When operating, depress the clutch pedal 1. Apply hand brake and switch off completely. Do not use the pedal as a foot ignition. rest (increases clutch wear). 2. Open bonnet and engage support. Driving and operation 135

Driving hints Brake servo unit Driving with a roof load The first 1000 km When the engine is not running, the brake Do not exceed the permissible roof load Drive your vehicle at various speeds. Do servo unit is no longer effective once the 3 226. For reasons of safety, distribute the not use full throttle. Never allow the engine brake pedal has been depressed once or load evenly and secure it properly with to labour at low revs. twice. Braking effect is not reduced, but retaining straps. Adjust tyre pressure to significantly greater force is required for load conditions. Do not drive faster Drive moderately. In all gears, only depress 3 braking. than 120 km/h. Check and retighten the the accelerator pedal around /4 of the way straps frequently. Observe country-specific down. Electric power steering 3 If the power assisted steering fails when regulations. Do not drive faster than three quarters of being towed with the engine switched off, Switching off the engine maximum speed. the vehicle can still be steered, but When you switch off, fans in the engine Do not brake unnecessarily hard for the considerably more force is required. compartment may continue running for a first 200 km. Driving in mountainous terrain or with a time to cool the engine. During the first drive smoke may develop trailer/caravan If the engine temperature is very high, e.g. because of wax and oil evaporating on the The cooling fan is electrically operated. Its after driving in mountainous terrain: allow exhaust system. Park the vehicle in the cooling power is therefore independent of the engine to idle for approximately two open for a while after the first drive and the engine speed. minutes in order to prevent heat avoid inhaling the fumes. Since a considerable amount of heat is accumulation. Fuel and engine oil consumption is higher generated at high engine speeds and less Vehicles with turbocharged engine 3 than normal during the running-in period. at slower speeds, do not shift down when After running at high engine speeds or high climbing hills whilst the vehicle is still coping engine loads, operate the engine briefly Never coast with engine not running with the gradient in the higher gear. at a low load or run in neutral for Many units will not function in this situation approx. 30 seconds before switching off in 3 (e.g. brake servo unit, power steering ). order to protect the turbocharger. Driving in this manner is a danger to yourself and others. 136 Driving and operation

Save energy – more kilometres Warming up Cooling fan Please observe the running-in hints on the Allow the engine to warm up while driving. The cooling fan is controlled via a previous page and the tips for energy Do not warm it up by letting it run at idling thermoswitch and therefore only runs if saving on the following pages. speed. Do not apply full throttle until the necessary. Good, technically correct and economical engine has reached operating The cooling fan automatically switches on driving ensures maximum durability and temperature. when the diesel particle filter is being performance for your vehicle. After a cold start, the manual transmission cleaned 3 depending on the engine. 3 Overrun cut-off automated does not switch to higher Pedals The fuel supply is automatically cut off gears until the speed increases when it is in Do not place any objects in the foot well during overrun, e.g. when the vehicle is automatic mode. This allows the catalytic which could slip under the pedals and driven with a gear engaged but no throttle converter to reach the temperature quickly inhibit the pedal travel. application. Overrun cut-off is deactivated which is required for optimum emission reduction. To ensure the pedal travel is uninhibited, if catalytic converter temperature is high. there must be no mats in the area of the Vehicles with turbocharged engine 3 Correct gear selection pedals. Flow-generated noises may be audible if Do not race your engine whilst in neutral or with a low gear selected. Driving too fast in Battery care the accelerator is released quickly on When driving slowly or when the vehicle is account of air flow in the turbocharger. individual gears as well as stop-and-go traffic increases engine wear and fuel stationary, e.g. in slow urban traffic, stop- Engine speed consumption. and-go traffic or traffic jams, turn off all Drive in a low engine speed range for each unnecessary electrical loads where gear as much as possible. Change down possible (e.g. heated rear window, heated When decreasing speed, shift down into front seats, etc.). the next lowest gear. Do not slip the clutch with a high-revving engine. This is Declutch when starting in order to relieve especially important when hill climbing. the strain on the starter and the battery. Driving and operation 137

Saving fuel, protecting the End-of-life vehicle recovery Warming up environment Information on end-of-life vehicle recovery z Full throttle and warming up at idle Trend-setting technology centres and the recycling of end-of-life speed increase wear, fuel consumption, Environmentally friendly and mainly vehicles is available at www.opel.com. exhaust emission, the amount of recyclable materials were used when your Energy and environment-conscious pollutant in the exhaust and the amount vehicle was being developed and driving of noise. manufactured. The production methods z High noise levels and exhaust emissions z Drive off immediately after starting. used to make your vehicle are also are often a result of driving without due Warm up the engine by running it at environmentally-compatible. attention to saving energy and moderate engine speeds. Recycling of production wastes keeps the protecting the environment. Uniform speed circulation of material closed. Reduction of z You should therefore drive with energy in z Hectic driving significantly increases fuel energy and water requirements also helps mind: "more miles – less fuel". consumption, the exhaust emissions, the to conserve natural resources. Reduce the noise level and exhaust proportion of pollutant in the exhaust A highly advanced design means that your emissions by adopting an environment- gas and the noise level. vehicle can be easily disassembled at the conscious driving style. This is extremely z Do not accelerate and brake end of its working life, and the individual worthwhile and improves the quality of unnecessarily. Drive at uniform speed, materials separated for subsequent re-use. life. watching the road. Materials such as asbestos and cadmium Fuel consumption depends to a great Avoid frequent starting off and stopping are not used. The refrigerant in the air extent on your own personal driving e.g. at traffic lights, in short distance conditioning system 3 is CFC-free. style. The following hints are intended to traffic and in queues of traffic by means New painting techniques employ water as help you consume fuel at a rate that is as of clever planning. Select roads with a solvent. close as possible to the specified levels good traffic flow. 3 224. Idling Check your vehicle’s fuel consumption z The engine also consumes fuel when every time you refuel. This facilitates idling. early detection of any irregularities z If you have to wait for more than one causing increased fuel consumption. minute, it is worthwhile switching off the engine. Five minutes of idling corresponds to approximately one kilometre of driving. 138 Driving and operation

Overrun z Slightly releasing the accelerator pedal Repair and maintenance z The fuel supply is shut off automatically results in distinct fuel savings with no z Improper repairs or adjustment and on overrun, e.g. when descending steep major loss of speed. maintenance work can increase fuel 3 hills or when braking 136. Drive at no more than around three consumption. Do not carry out work on z To enable the overrun cut-off to come quarters of maximum speed and you will the engine yourself. into action and save fuel, do not use up to 50 % less fuel, without losing a You may out of ignorance infringe accelerate or declutch during overrun. great deal of time. environmental laws by not disposing of Correct gear selection Tyre pressure materials properly. z High revs increase engine wear and fuel z Inadequate tyre pressure, leading to Appropriate parts might not be recycled. consumption. higher road resistance, costs money in Contact with some of the materials z Do not race your engine. Avoid driving at two ways: for more fuel and increased involved may pose a health hazard. tyre wear. high engine speeds. z We recommend that repair and z Making use of the tachometer helps to Regular checks (every 14 days) pay off. maintenance be entrusted to your Opel save fuel. Drive in a low engine speed Electrical loads Partner. z range for each gear as much as possible The power consumption of electrical Extreme driving conditions with uniform engine speeds. Drive as equipment increases fuel consumption. z Going up steep slopes, cornering, driving often as possible in top gear, select the z Switch off all auxiliary electrical loads on poor roads and winter driving all next higher gear as soon as possible, (e.g. air conditioning 3, heated rear increase fuel consumption. and only change down when the engine window) when not needed. is no longer running perfectly smoothly. Fuel consumption increases dramatically Roof racks, ski-holders in urban traffic and at winter High speed z Due to air resistance, a roof load can temperatures, especially on short trips z The higher the speed, the higher the increase fuel consumption by when the engine operating temperature consumption and the noise level. At top approx. 1l/100 km. is not reached. speed, you consume a great deal of fuel and produce excessive noise and z Remove them if they are not being used. z Follow the hints given above to keep exhaust emissions. consumption to a minimum under such conditions. Driving and operation 139

Fuels, refuelling Fuel for petrol engines Fuel for diesel engines Fuel consumption Only use unleaded fuel that complies Only use diesel fuel that complies The fuel consumption is determined under with DIN EN 228. with DIN EN 590. The fuel must have low specified driving conditions 3 224. Fuels with ethanol content greater than 5 % sulphur content (maximum 50 ppm). Special equipment increases the weight of may only be used if the vehicle has been Do not use marine diesel oils, heating oils the vehicle. As a result, they can increase specifically developed and approved for or entirely or partially plant-based diesel fuel consumption and reduce the specified these fuels. fuels, such as rape seed oil or bio diesel, maximum speed. Use fuel with the recommended octane Aquazole and similar diesel-water rating (value in bold 3 220). Use of fuel emulsions. Diesel fuels must not be diluted For the first few thousand kilometres, with fuels for petrol engines. friction between the engine and with too low an octane rating can reduce transmission components is higher. This engine power and torque and will slightly The flow and filterability of diesel fuel are increases fuel consumption. increase fuel consumption. temperature-dependent. When temperatures are low, refuel with diesel fuel Caution with guaranteed winter properties. Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage. 140 Driving and operation

Fuel filler cap Only a Opel Genuine fuel filler cap provides 9 Warning full functionality. Diesel-engined vehicles have special fuel filler caps. Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this rectified immediately by a workshop.

Picture no: 15829t.tif Refuelling 9 Warning Before refuelling, switch off engine and any external heaters with combustion chambers 3 (identified by sticker on tank flap). Switch off any mobile phones. Follow the operating and safety instructions of the filling station when refueling. Driving and operation 141

Correct filling depends to a large extent on Close fuel tank cover. proper operation of the fuel dispensing pump: Caution 1. Fully insert the pump nozzle and switch it Wipe off any overflowing fuel on. immediately. 2. After automatically switching off, the specified tank capacity is achieved by means of metered refuelling (twice). Insert fuel dispensing pump as far as possible. To close, place fuel filler cap in position and turn, overcoming the resistance until the ratchet on the cap engages audibly. Picture no: 14191s.tif Fuel filler neck at right rear side of vehicle. The tank flap is locked together with the doors 3 30. Open tank flap. Unscrew the fuel filler cap, remove and suspend from the tank flap. The fuel tank has a limiting system which prevents overfilling of the tank. 142 Driving and operation

Fuel grades other than those listed on pages 139, 220 (e. g. LRP = Lead Replacement Petrol or leaded fuel) could damage the catalytic converter or electronic components.

Caution Damage to the catalytic converter or the vehicle may result if the following points are not observed.

z In the event of misfiring, uneven engine running, a clear reduction in engine performance or other unusual problems, Picture no: 6448u.tif have the cause of the fault rectified by a Picture no: 17875s.tif Catalytic converter, exhaust workshop as soon as possible. In an Controlling exhaust emission gasses emergency, driving can be continued for Design measures, primarily in the fuel a short period, keeping vehicle speed injection system and ignition system zones Catalytic converter and engine speed low. The catalytic converter reduces the in combination with the catalytic converter, amount of harmful substances in the This does not apply when the Electronic the amount of hazardous substances in the Plus 3 exhaust gas, such as carbon monoxide Stability Program (ESP® ) kicks in exhaust emissions, such as carbon 3 (CO), hydrocarbons, (CH) and nitrous 146. monoxide (CO), hydrocarbons (CH) and nitrogen oxides (NO ), are reduced to a oxide (NO ). z If unburnt fuel enters the catalytic x x minimum. converter of a , this may result in overheating and irreparable damage to the catalytic converter. You should therefore avoid unnecessarily long use of the starter when starting off, running the tank dry and starting the engine by pushing or towing. Driving and operation 143

If it illuminates briefly, but does not recur, it is of no significance. Lighting of A may indicate water in the diesel fuel filter 3. Have the fuel filter checked for water residue 3 212. If it flashes after the ignition is switched on, there is a fault in the immobiliser system. The engine cannot be started 3 27.

Picture no: 17891s.tif Picture no: 17880s.tif Control indicator Z for exhaust Control indicator A for engine electronics Illuminates when the ignition is switched on Illuminates for a few seconds after the and during the start attempt. Goes off ignition is switched on. shortly after the engine starts running. If it illuminates when the engine is running, Illumination whilst the engine is running there is a fault in engine or transmission indicates a fault in the emission control electronics. The electronic system switches system. The permissible emission limits to an emergency running programme. Fuel may be exceeded. Contact a workshop for consumption may be increased and the assistance immediately. driveability of the vehicle may be impaired. Illumination with the engine running In some cases the fault can be remedied by indicates a fault that can cause damage to switching the engine off and starting it the catalytic converter. It is possible to again. If the control indicator continues to continue driving without causing damage illuminate whilst the engine is running, by slowing down until the flashing stops contact a workshop for assistance in and the control indicator illuminates. remedying the cause of the fault. Contact a workshop for assistance immediately. 144 Driving and operation

Engine exhaust Under certain driving conditions, e.g. short journeys, the system may not clean itself 9 Warning automatically. Engine exhaust gases contain poisonous If the filter requires cleaning and previous carbon monoxide, which is colourless driving conditions did not enable and odourless and could be fatal if automatic cleaning, control indicator ! inhaled. flashes. Continue driving, keeping engine speed above 2000 rpm-1. Shift down if If exhaust gases penetrate the vehicle, necessary. Diesel particle filter cleaning is open windows and contact a workshop then initiated. for assistance. Avoid driving with the tailgate open, since exhaust gas can enter the interior of the vehicle. Picture no: 18600S.tif Diesel particle filter 3 The diesel particle filter system filters harmful soot particles out of the exhaust gases. The system includes a self-cleaning function that run automatically during driving. The filter is cleaned by burning off the soot particles at high temperature. This process takes place automatically under set driving conditions and may take up to 25 minutes. Fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. Driving and operation 145

Maintenance Have all maintenance work carried out at the specified intervals. We recommend that you entrust this work to your Opel Partner, who has proper equipment and trained personnel available. Electronic testing systems permit rapid diagnosis and remedy of faults. This way you can be certain that all components of the vehicle’s electrical, injection and ignition systems operate correctly, that your vehicle has a low level of pollutant emission and that the catalytic converter system will have a long service life. Picture no: 18535s.tif Picture no: 18603s.tif You are thereby making an important We recommend not stopping driving The control indicator ! goes off as soon as contribution towards keeping the air clean during cleaning, and not switching off the the self-cleaning operation is complete. and compliance with emissions legislation. ignition. Cleaning is fastest at high engine Checking and adjustment of the fuel- revs and high loads. injection and ignition systems is included in the inspection. For this reason, you should have all maintenance work carried out at the intervals specified in your Service and Warranty Booklet. 146 Driving and operation

Drive Control Systems As soon as the vehicle starts to swerve The vehicle is now in a critical situation; Plus Electronic Stability Program (ESP®Plus) 3 (understeer/oversteer), engine output is ESP® allows you to keep control of the ESP®Plus improves driving stability when reduced and the wheels are braked vehicle and reminds you to match your necessary in any driving situation individually. This considerably improves speed to the road conditions. regardless of the type of road surface or the driving stability of the vehicle on tyre grip. It also prevents the drive wheels slippery road surfaces. 9 Warning Plus from spinning. ESP® is ready for operation as soon as Do not let this special safety feature the ignition is switched on and control tempt you into taking risks when driving. indicator v goes out. ESP®Plus does not negate the laws of When ESP®Plus comes into action, v physics. flashes. Adapt speed to the road conditions. Driving and operation 147

Control indicator v Illuminates after interruption of power The warning light lights up for a few supply e.g. after disconnecting battery. seconds when ignition is switched on. Once After a power supply interruption the it goes out, the system is ready for steering angle sensor must be calibrated to operation. make the system operational: Flashing during driving: z Automatic calibration driving in straight This shows the system has come into line at constant slow (20 to 40 km/h) action. The engine output may be reduced speed on level, dry road. (the sound of the engine changes) and the z Manual calibration by turning steering vehicle may be braked automatically to a wheel from limit position to limit position. small degree. If the indicator lamp does not go off after successful calibration, observe notes in middle column. Picture no: 17892s.tif Illuminates while driving: Fault in the system. Driving can be continued. Poor road surface conditions may however still cause vehicle stability to be impaired. Have the cause of the fault eliminated. Self-diagnosis integrated into the system allows rapid fault identification. 148 Driving and operation

Cruise control 3 For manual transmission automated 3, Cruise control can store and maintain engage cruise control in automatic mode speeds of approx. 30 to 200 km/h. only. Deviation from the stored speed is possible on uphill or downhill inclines. 9 Warning For safety reasons the cruise control When the cruise control is active, cannot be activated until the foot brake reaction times may be increased due to has been operated once. the different position of the feet. The cruise control is operated with the buttons I, R and O on the turn signal lever. Do not use the cruise control if it is not advisable to maintain a constant speed (e.g. in situations presenting a danger to yourself and other road users, in heavy traffic or on winding, slippery or greasy Picture no: 17893s.tif Control indicator m 3 roads). The warning lamp lights up for a few seconds 3 when the ignition is switched on. The system is now ready for operation. When driving, the warning lamp m lights up as soon as the system is switched on. Driving and operation 149

Accelerate To deactivate With cruise control activated, hold down Briefly press the O button: cruise control is button I or briefly press it repeatedly: deactivated. speed is increased continuously or in steps Automatic deactivation: of 2 km/h. z vehicle speed below approx. 30 km/h The current speed is stored and saved after the I button has been released. z the brake pedal is depressed Decelerate z the clutch pedal is depressed 3 With cruise control active, hold down z move the selector lever on the manual button R or briefly press it repeatedly: transmission automated 3 to N speed is reduced continuously or in steps of 2 km/h. Stored speed The speed is saved until the ignition is The current speed is stored and saved after switched off. the R button has been released. Picture no: 7758u.tif To resume the saved speed, briefly press To activate the R button at a speed above 30 km/h. Tap button I: the current speed is stored and maintained. The accelerator pedal can be released. Vehicle speed can be increased by depressing the accelerator pedal. When the accelerator pedal is released, the previously stored speed is resumed. 150 Driving and operation

Ultrasonic parking sensors 3 Towing equipment, caravan/trailer towing Park pilot makes reverse parking easier by If a towing device is subsequently fitted to measuring the distance between the back the vehicle, the system must be set to the of the vehicle and obstacles to the rear. It is modified vehicle length by a workshop. the driver, however, who maintains full When operating without a trailer, the tow responsibility for parking. bar must be removed else the system can The system records the distance using four be damaged. sensors in the rear bumper. Fitting rear load racks 3 To activate Rear carriers, e. g. bike carriers, could The park pilot system activates cause system malfunction. automatically when the ignition is switched Fault on and reverse gear is engaged. On system faults, a permanent tone Operational readiness is indicated by a sounds at a distance of 1 metre from the brief tone. obstacle. Have the cause of the fault Picture no: 14779s.tif If the vehicle approaches an obstacle, a eliminated by a workshop. series of acoustic signals sound. The interval 9 Warning In order to avoid operational problems or between the signals becomes shorter as the erroneous information, the sensors must be vehicle gets closer to the obstacle. When the Under certain circumstances, various undamaged and free of soiling, snow and distance is less than 30 cm, the signal is reflective surfaces on objects or clothing ice. continuous. as well as external noise sources may cause the system to fail to detect obstacles.

To deactivate The system deactivates automatically when reverse gear is disengaged. Driving and operation 151

To ensure that full pedal travel can be utilised, especially in case of a fault in one of the brake circuits, there must be no mats in the vicinity of the pedals 3 136. When the engine is not running, the support of the brake servo unit disappears once the brake pedal has been depressed once or twice. Braking effect is not reduced, but braking requires significantly greater force. This is especially important to bear in mind when towing. The brake fluid level should be checked regularly. If the brake fluid level is too low and the hand brake is not applied, control Picture no: 14722s.tif indicator R on the instrument panel Picture no: 17894s.tif Hydraulic brake system illuminates 3 85. Brake system control indicator R The brake system comprises two The control indicator illuminates after the independent brake circuits. ignition is turned on, when the hand brake is applied or if the brake or clutch fluid level If a brake circuit fails, the vehicle can still be is too low. Brake fluid 3 214. braked using the other brake circuit. However, the brake pedal must be 9 Warning depressed a considerable way before any braking effect occurs, and much more If the control indicator illuminates when force is required. The braking distance is the hand brake is released, stop driving longer. Contact a workshop for assistance immediately. Contact a workshop for before continuing to drive. assistance. 152 Driving and operation

For vehicles with manual transmission Self testing automated 3, the control indicator flashes When the engine is started and the vehicle for a few seconds when the ignition is starts off, the system performs a self-check, turned off when the hand brake is not which may be audible. applied. Fault u Anti-lock brake system (ABS ) 9 Warning ABS prevents the wheels from locking. If there is a fault in the ABS, the wheels ABS starts to regulate brake pressure as may be liable to lock due to braking that soon as a wheel shows a tendency to lock. is heavier than normal. The advantages The vehicle remains steerable, even during of ABS are no longer available. During hard braking. hard braking, the vehicle can no longer ABS control is made apparent though a be steered and may swerve. pulse in the brake pedal and the noise of the regulation process. Picture no: 17895s.tif Have cause of fault remedied by a Control indicator u for ABS workshop. The system’s integrated self For optimum braking, keep the brake It illuminates for a few seconds when diagnostics allow faults to be quickly pedal fully depressed throughout the ignition is switched on. Once the control remedied. braking process, despite the fact that the indicator goes out, the system is ready for pedal is pulsating. Do not reduce the operation. pressure on the pedal. If the control indicator does not go out after a few seconds, or if it illuminates while driving, there is a fault in the ABS. The brake system remains operational without ABS regulation. Adaptive brake lamp 3 During full-on braking, all three brake lamps flash for the duration of ABS control. Driving and operation 153

Brake assist Wheels, tyres If the brake pedal is operated quickly with Suitable tyres and restrictions 3 228. a powerful push, the vehicle is Tyres fitted in the factory are adapted to automatically braked at full braking power the chassis and provide optimum driving in order to achieve the shortest possible comfort and safety. braking distance when full-on braking occurs (brake assist). Changing tyre/wheel type If tyres of a different size than those fitted Maintain steady pressure on the brake at the factory are used, it may be pedal for as long as full-on braking is to necessary to reprogram the electronic continue. When the brake pedal is speedometer and make other vehicle released, the maximum brake force modifications. amplification is taken away. After converting to a different tyre size, Hill Start Assist 3 (HSA) have the adhesive label with tyre pressures Picture no: 14723s.tif The system helps pull away on inclines. replaced. Hand brake After releasing the footbrake, if the hand brake is not applied the brakes are only 9 Warning Always apply hand brake firmly without released after 2 seconds. As soon as the pressing the release button, and apply as acceleration is sufficient to prevent rolling Use of unsuitable tyres or wheels may firmly as possible on steep slopes. back, the brake is released. lead to accidents and render the vehicle To release the hand brake pull lever up unroadworthy. slightly, press release button, and lower lever all the way down. To reduce the operating forces of the hand brake, depress the foot brake at the same time. 154 Driving and operation

Fitting new tyres Always inflate the spare wheel 3 to the Fit tyres in pairs or in sets, which is even pressure specified for full load. better. Ensure that tyres on one axle are Do not reduce tyre pressure when the tyres z the same size are warm. Otherwise the pressure may z the same design drop below the permissible minimum when z the same make the tyres cool down. z and have the same tread pattern After having checked the tyre pressure, tighten the valve caps using the valve cap Fit directional tyres such that they roll in the key. direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on Incorrect inflation pressures will impair the sidewall. safety, vehicle handling, comfort and fuel economy and will increase tyre wear. Tyres fitted opposing the rolling direction (such as when changing a tyre) should be refitted as soon as possible. This is the only Picture no: 14194s.tif way to benefit fully from the design Tyre pressure properties of the tyre. Check tyre pressure, including the spare wheel, at least every 14 days and prior to Pay attention to legal requirements when any long journey; the tyres should be disposing of tyres. checked when cold. Don’t forget to check the spare wheel 3. Remove the valve cap key from the tank flap and use it to unscrew the valve cap. Tyre pressure 3 228 and on the adhesive label 3 on the inside of the tank flap. The tyre pressure data is for cold tyres. It applies to both summer and winter tyres. Driving and operation 155

Picture no: 9358t.tif Picture no: 15941s.tif Picture no: 6457u.tif Tyre condition, wheel condition Tread depth 9 Warning Drive over edges slowly and at right angles Check tread depth regularly. if possible. Driving over sharp edges can If the pressure is too low, this can result For reasons of safety, tyres should be cause tyre and wheel damage. Do not trap replaced when their tread depth has worn in considerable tyre warm-up and tyres on the kerb when parking. internal damage, leading to tread down to 2 to 3 mm (winter tyres: 4 mm). separation and even to tyre blow-out at Regularly check wheels for damage. Seek The legally permissible minimum tread high speeds. the assistance of a workshop if there is any depth (1.6 mm) has been reached when damage or unusual wear. the tread has worn down as far as one of the wear indicators (TWI1)). A number of wear indicators are spaced at equal intervals around the tyre within the tread. Their position is indicated by markings on the tyre sidewall.

1) TWI = Tread Wear Indicator. 156 Driving and operation

General information Tyre designations z The risk of aquaplaning is greater if the Meanings: tyres are worn. e.g. 175/70 R 14 88 T z Tyres age, even if they are not used or 175 =Tyre width in mm used infrequently. We recommend tyre replacement every six years at the latest. 70 = Cross-section ratio (tyre height to tyre width in %) z Never fit used tyres the previous history R = Belt type Radial and use of which you do not know. 14 = diameter in inches 88 = Load index e.g. 88 corresponds to 567 kg T = Speed code letter: Speed code letters:

Picture no: 6456u.tif Q = Up to 160 km/h If wear in the front is greater than that in S = Up to 180 km/h the rear, move the rear wheels to the front T = Up to 190 km/h axle and vice versa. H = Up to 210 km/h Correct tyre pressure. V = Up to 240 km/h W = Up to 270 km/h Driving and operation 157

Winter tyres 3 Wheel trims must not impair brake cooling. 3 Notes on fitting new tyres 154. Remove the wheel trims if fitting tyre Restrictions 3 228. chains 3. Winter tyres improve driving safety at temperatures below 7 C. 9 Warning The design of summer tyres means they Use of unsuitable tyres or wheel trims have limited qualities for winter driving. could lead to sudden loss of air and thereby accidents. In accordance with country-specific regulations, affix the speed sticker 3 in the driver’s field of view. If you use the spare wheel when it is fitted with a summer tyre, the vehicle’s driveability may be affected, especially on slippery road surfaces. Obtain a Picture no: 6459u.tif replacement for the faulty tyre as soon as Tyre chains 3 possible, and have the wheel balanced Restrictions and further information 3 228. and fitted to the vehicle. Tyre chains are only permitted on the Wheel covers 3 driven wheels (front axle). They must be Use of wheel trims and tyres that approved fitted to the tyres symmetrically in order to by Opel for the vehicle in question and achieve a concentric fit. thereby fulfil all requirements for the wheel Always use fine mesh chains that add no and tyre combination. more than 10 mm to the tyre tread and the If the wheel trims and tyres used are not inboard sides (including chain lock). Opel-approved, the tyres must not have a beaded edge. 158 Driving and operation

Remove the wheel trims if using tyre chains Roof rack 3 Towing equipment 3 3 174. For safety reasons and to avoid roof Only use towing equipment that has been Tyre chains may only be used at speeds up damage we recommend using the Opel approved for your vehicle. Ask a workshop to 50 km/h. When travelling on roads that roof rack system that is approved for your to retrofit towing equipment. It may be are free of snow, they may only be used for vehicle. necessary to make changes that affect the brief periods. Follow the usage instructions for the roof cooling system, heat shields or other rack. equipment. 9 Warning Remove the roof rack when not in use. Mounting dimensions of towing equipment 3 232. Damage may lead to tyre blowout. Disengage covers concealing roof rack Tyre chains must not be used on the mounts by pushing sliders in direction of temporary spare wheel. If you need to use arrow (e.g. with coin) and remove. To close tyre chains after suffering a flat front tyre, roof rack mounts, insert covers at front and fit the temporary spare on the rear axle engage sliders at rear. and transfer one of the rear wheels to the Driving hints 3 135 front axle. Driving and operation 159

Picture no: 14195s.tif Picture no: 15271s.tif Picture no: 12416t.tif Towing equipment with Fitting the coupling ball bar Checking the tensioning of the coupling removable coupling ball bar 3 Fold down the socket. Remove the sealing ball bar plug from the hole for the coupling ball bar z Red marking on rotary knob must point Caution and stow it in the luggage compartment. towards white marking on coupling ball bar. The coupling ball bar is to be removed when not towing. z The gap between the rotary knob and the coupling ball bar must be Stowage of coupling ball bar approx. 4 mm. The coupling ball bar is located in a bag z Key in the lock must be at position 1. with the vehicle tools housed under the spare wheel - see Fig. above. Spare wheel 3 3 172. On vehicles with tyre repair kit 3, the coupling ball bar is located in the left stowage compartment beneath the floor cover in the luggage compartment 3 162, Fig. 17923 S. 160 Driving and operation

Picture no: 12417t.tif Picture no: 12418t.tif Picture no: 16484s.tif Otherwise, the coupling ball bar must be Inserting the coupling ball bar Lock the coupling ball bar in position by tensioned before it is inserted into the Insert the tensioned coupling ball bar in the turning key to position 2 3 159, coupling housing: housing and push firmly upwards until it Fig. 12416 T. Remove the key and press the z Unlock coupling ball bar by turning key audibly engages. protective flap into place. 3 to position 1 159, Fig. 12416 T. The rotary handle snaps back into its home When the coupling ball bar is locked the z Pull out rotary knob and turn clockwise position resting against the coupling ball turn knob can no longer be pulled out. as far as it will go, see Fig. bar (no gap).

9 Warning Do not touch rotary handle during insertion. Driving and operation 161

Check that the coupling ball bar is correctly installed z Green marking on rotary knob must point towards white marking on coupling ball bar z There must be no gap between the rotary handle and the coupling ball bar z The coupling ball bar must be firmly engaged in the opening z The coupling ball bar must be locked and the key removed

9 Warning Towing a caravan/trailer is only Picture no: 12421t.tif Picture no: 13670t.tif permitted with a properly fitted coupling Eye for break-away stopping cable Dismounting the coupling ball bar ball bar. If the coupling ball bar cannot In the case of trailers/caravans with brakes, Open the protective flap and turn the key be correctly fitted, please contact a attach breakaway stopping cable to eye. to position 1 to unlock the coupling ball bar workshop for assistance. 3 159, Fig. 12416 T. Pull out rotary handle and turn clockwise as far as it will go. Pull out coupling ball bar downwards. Insert the sealing plug in the opening for the coupling ball bar. Close the socket 3 159, Fig. 15271 S. 162 Driving and operation

Caravan/trailer towing The permitted caravan/trailer load applies Caravan and trailer loads1) up to the specified incline and up to an The permissible caravan/trailer loads are altitude of 1000 metres above sea level. vehicle and engine-dependent maximum Since engine power decreases as altitude values which must not be exceeded. The increases because of the air becoming actual caravan/trailer load is the difference thinner, therefore reducing climbing ability, between the actual gross weight of the the permitted towing weight also caravan/trailer and the actual coupling decreases by 10 % for every 1000 metres of socket load with the caravan/trailer additional altitude. The towing weight coupled. does not have to be reduced when driving on roads with slight inclines (less than 8 %, The permissible caravan/trailer loads are e.g. motorways). specified in the vehicle documents. In general, they are valid for gradients up to The permissible gross train weight must not maximum 12% be exceeded. This weight is specified on 3 Picture no: 17923s.tif the identification plate 218. Stowage of coupling ball bar Place coupling ball bar in bag and clip onto the tool kit below the spare wheel 3 159, Fig. 14195 S. On vehicles with tyre repair kit 3, the coupling ball bar is stored in the left stowage compartment beneath the floor cover in the luggage compartment - see Fig. above.

1) Observe national regulations. Driving and operation 163

Coupling socket load Rear axle load during towing Driving characteristics, towing tips The coupling socket load is the load With the trailer connected and the towing Before attaching the trailer/caravan, exerted by the trailer/caravan on the vehicle fully loaded including all lubricate the ball of the trailer/caravan coupling ball. It can be varied by changing occupants, the permitted rear axle load towing device. However, do not lubricate the weight distribution when loading the (specified on the identification plate and the ball if a stabiliser, which acts on the trailer/caravan. vehicle documents) must be exceeded by coupling ball, is being used to damp The maximum permissible coupling socket no more than 25 kg and the maximum hunting. load (55 kg) of the towing vehicle is permitted gross vehicle weight by no more Check caravan/trailer lighting before specified on the towing equipment than 30 kg. If the maximum permitted rear starting to drive. The fog tail lamps on the identification plate and in the vehicle axle load is exceeded, a maximum speed vehicle are deactivated when towing a documents. This must always be complied of 100 km/h applies, and 80 km/h for caravan or trailer. commercial vehicles. with, particularly in the case of heavy Trailers with LED turn signals must have a caravans/trailers. The coupling socket load provision enables lamp monitoring for should be no less than 25 kg. commercial bulbs. When measuring the coupling socket load, Handling is greatly influenced by the make sure that the drawbar of the loaded loading of the trailer/caravan. Loads trailer/caravan is at the same height as it should therefore be secured so that they will be when the trailer/caravan is coupled cannot slip and be placed in the centre of with the towing vehicle loaded. Particularly the trailer/caravan if possible, i.e. above important for trailers/caravans with the axle. tandem axle. In the case of trailers with low driving stability, do not exceed a speed of 80 km/h; the use of a friction-type stabiliser is strongly recommended. 164 Driving and operation

If the trailer/caravan starts to sway, drive Starting on inclines Before starting off under extreme more slowly, do not attempt to correct the For vehicles with manual transmission, operating conditions, switch off steering and brake sharply if necessary. the most favourable engine speed unnecessary consumers. If it is necessary to apply the brakes fully, when starting off on an incline is depress the brake pedal as hard as between 2500 and 3000 rpm for petrol possible. engines and between 2000 and 2500 rpm for diesel engines. Hold engine speed Remember that the braking distance for constant, engage clutch gradually (let slip) vehicles towing caravans/trailers with and – release hand brake – and open throttle. If without brake is always greater than that possible, the engine speed should not drop for vehicles not towing a caravan/trailer. during this procedure. When driving downhill, drive in the same For vehicles with manual transmission gear as if driving uphill and drive at a automated 3 in Automatic mode simply similar speed. apply full gas. Adjust tyre pressure to the value specified for full load 3 228. Self-help, vehicle care 165

Self-help, vehicle care Diesel fuel system, bleeding If the tank is allowed to run dry, the diesel Diesel fuel system, bleeding ...... 165 fuel system must be bled. Turn over the Bonnet ...... 165 ignition three times for 15 seconds at a time. Then start the engine for a maximum Starting the engine with jump of 40 seconds1). Repeat this process after leads 3...... 166 no less than 5 seconds. If the engine fails to Towing...... 168 start, seek the assistance of a workshop. Warning triangle ¨ 3, First-aid kit +3...... 171 Jack £ 3 and vehicle tools 3 ...... 171 Spare wheel 3...... 172 Changing wheels ...... 174 Tyre repair kit 3...... 178 Electrical system ...... 181 Picture no: 16109s.tif Fuses and the most important circuits Bonnet they protect ...... 182 Pull the release lever located on the driver’s Bulb replacement ...... 185 side below the instrument panel and push Vehicle care...... 196 it back to its original position.

1) For technical reasons, only 30 seconds are possible on engines Y 17 DT and Z 17 DTH 166 Self-help, vehicle care

Starting the engine with jump leads 3 Do not use a rapid charger or push or two the vehicle to get it started. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle.

9 Warning Starting the engine with jump leads must be carried out with the utmost caution. Any deviation from the following instruction may lead to injury or damage Picture no: 17883s.tif Picture no: 14733s.tif due to the explosion of the batteries and Pull the safety catch and open the bonnet. Secure the bonnet support. Before closing to damage of the electrics in both vehicles. Any dirt or snow on the bonnet can slide the bonnet, press the support into the down toward the windscreen when the holder. bonnet is opened and block the air intake Lower the bonnet and allow it to drop into 3 127. the catch. Check that the bonnet is engaged. Self-help, vehicle care 167

z Use a booster battery with the same voltage (12 volts). Its capacity (Ah) must not be much less than that of the discharged battery. z Use jump leads with insulated terminals and a cross section of at least 16 mm2 (25 mm2 for diesel engines). z Do not disconnect the discharged battery from the vehicle. z Switch off all unnecessary electrical consumers. z Do not lean over the battery during jump starting. Picture no: 15286a.tif z Do not allow the terminals of one lead to Picture no: 16485s.tif z Never expose the battery to naked touch those of the other lead. Lead connection order: flames or sparks. z The vehicles must not come into contact 1. Connect the red lead to the positive z A flat battery can freeze at temperatures with each other during the jump starting terminal 1 of the booster battery. around 0 C. Defrost the battery before process. 2. Connect the other red lead to the connecting up jump leads. z Apply the handbrake. Gear lever in positive terminal 2 of the discharged z Do not allow battery fluid to come into neutral. battery. contact with eyes, skin, fabrics or 3. Connect the black lead to the negative painted surfaces. The fluid contains terminal 3 of the booster battery. sulphuric acid which can cause injuries and damage in the event of direct 4. Connect the other end of the black contact. lead 4 to a vehicle grounding point, such as the engine block or a screw z Wear eye protection and protective connection in the engine suspension. clothing when handling a battery. Connect as far away from the discharged battery as possible. 168 Self-help, vehicle care

Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump start. 2. After 5 minutes, start the other engine. Start attempts should be made at intervals of 1 minute not last longer than 15 seconds. 3. Allow both engines to idle for approx. 3 minutes with the leads connected. 4. Switch on electrical consumers (e.g. light, heated rear window) of the vehicle Picture no: 17896s.tif Picture no: 14198s.tif receiving the jump start. Towing The towing eye is in the tool kit 3 in the Towing your own vehicle luggage compartment underneath the 5. Reverse above sequence exactly when spare wheel 3, see Fig. above, or for removing leads. Disengage cap at bottom and remove downwards. versions with tyre repair kit 3, in the storage compartment underneath the floor cover, see Fig. 17918 S. Self-help, vehicle care 169

Switch on ignition to release steering column lock and to permit operation of brake lamps, horn and windscreen wipers. Gear lever in neutral.

Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle.

Picture no: 17918s.tif Picture no: 17897s.tif Screw in the towing eye anticlockwise as far When the engine is not running, as it will go until it stops in a horizontal considerably more force is needed to brake position. and steer. Attach a tow rope 3 – or better still a tow To prevent the entry of exhaust fumes from rod 3 – to the eye. the towing vehicle, switch on the air 3 The towing eye may only be used for recirculation and close the windows. towing and not for recovery of the vehicle. Contact a workshop for assistance. 170 Self-help, vehicle care

If the automatic clutch has been manually disengaged in vehicles with manual automated transmission 3 towing is not permitted 3 134. In this case, contact a workshop for assistance immediately. After towing, unscrew towing eye by rotating clockwise and insert and close the cap.

Picture no: 14199s.tif Picture no: 17898s.tif Towing another vehicle On some versions, the towing eye is located Attach a tow rope 3 – or better still a tow behind a cover. 3 rod – to the rear towing eye on the right Slacken the screw a quarter turn with a side of the vehicle underbody, but never to screwdriver (see Fig.) and remove the the rear axle. cover. The towing eye may only be used for towing and not for recovery of the vehicle.

Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle.

After towing, fit cover 3 and secure with bolt. Self-help, vehicle care 171

Picture no: 16140s.tif Picture no: 14201s.tif Picture no: 14203s.tif Warning triangle ¨ 3, To open, remove the luggage Jack £ 3 and vehicle tools 3 First-aid kit +3 compartment cover 3 3 55, lift the floor Vehicles with spare wheel 3 The warning triangle and first aid cushion using the handle and raise toward the The jack and vehicle tools are stowed in a are strapped with a rubber band in the front. bag underneath the spare wheel in the compartment on the left of the luggage luggage compartment. compartment beneath the floor covering. The jack 3 and the vehicle tools 3 have been specially developed for your vehicle and must only be used on that vehicle. Only use jack for changing wheels. 172 Self-help, vehicle care

Placing wide wheels in the spare wheel well The spare wheel well is not designed for all sizes of permitted tyres. If a wider wheel is stowed in the spare wheel well after changing wheels, the floor cover can rest on the protruding wheel. This must be taken into account when loading the luggage compartment.

Picture no: 17918s.tif Picture no: 16141s.tif Vehicles with tyre repair kit 3 Spare wheel 3 The jack and tyre repair kit are located in Some vehicles are equipped with a tyre the storage compartment below the floor repair kit instead of a spare wheel 3 178. covering in the luggage compartment. Storing the spare wheel in the luggage compartment The spare wheel is in the luggage compartment below the floor cover. It is mounted via a wing nut in a well in the vehicle floor. To access the spare wheel, remove the luggage compartment cover 3 3 55, lift the floor cover using the handle and raise toward the front. Fold the spare wheel cover up toward the front. Self-help, vehicle care 173

General information Notes on temporary spare wheel 3 Notes on directional tyres 3 Depending on version, the spare wheel z The use of the temporary spare wheel Fit directional tyres such that they roll in the may be in the form of a temporary spare may affect the handling of the vehicle, direction of travel. The rolling direction is wheel 3. Refer to the notes on this page particularly if winter tyres are being indicated by a symbol (e.g. an arrow) on and 3 157, 3 228. used 3. The Electronic Stability Program the sidewall. Plus 3 On vehicles with alloy wheels 3 the spare ESP® may switch itself off. Replace The following applies to tyres fitted wheel may have a steel rim. defective tyre as soon as possible, opposing the rolling direction: balance wheel and fit to vehicle. Use of a spare wheel together with winter z Driving conditions may be altered. Have z tyres could alter driving conditions. Have Fit only one temporary spare wheel. the defective tyre replaced as soon as the defective tyre replaced as soon as z Do not drive faster than 80 km/h. possible. possible. z Take curves slowly. z Do not drive faster than 80 km/h. Use of a spare wheel that is smaller than z Do not use the temporary spare wheel z Be especially careful when driving in rain the other wheels could alter driving for a lengthy period. and snow. conditions. In many countries, it is only permitted as a temporary spare wheel. z Replace temporary spare wheel with full Further information on directional tyres Have the defective tyre replaced as soon specification wheel without delay. 3 154. as possible. z Tyre chains are not permitted on the temporary spare wheel. If tyre chains have to be used after a front wheel puncture, fit temporary spare wheel to the rear axle and fit a rear wheel to the front axle. Check tyre pressure and correct if necessary 3 228. z Observe notes on temporary spare wheel on 3 157, 3 228. 174 Self-help, vehicle care

Changing wheels z If the ground on which the vehicle is z No people or animals may be in the There may be a tyre repair kit instead of a standing is soft, a solid board (max. 1 cm vehicle when it is jacked up. 3 spare wheel 3 178. thick) should be placed under the jack . z Never crawl under a jacked-up vehicle. z Make the following preparations and Block the wheel diagonally opposite the z Do not start the vehicle when it is raised observe the following information: wheel to be changed by placing wedge on the jack. blocks or equivalent in front and behind z Park the vehicle on a level, firm and non- the wheel. z Before screwing in the wheel bolts, clean skid surface. The front wheels must be in them and lightly coat the taper of each the straight-ahead position. wheel bolt with commercially available z Switch on the hazard warning flashers, grease. apply the hand brake, engage first gear or reverse. z Erect warning triangle as specified. Warning triangle 3 171. z Remove the spare wheel 3 172. z Never change more than one wheel at once. z Use the jack 3 only to change wheels. Self-help, vehicle care 175

Picture no: 14204s.tif Picture no: 11721s.tif Picture no: 11642s.tif 1. Pull off the wheel trim with the hook 3. Alloy wheels 3: Prise off the hub cap by Alloy wheels with anti-theft protection 3: Vehicle tools 3 171. inserting a screwdriver 3 in the recess at unscrew using the wheel nut 3 For wheel trims with visible wheel bolts 3: the side of the hub cap. Protect the rim socket and remove. Vehicle tools 171. The trim can remain on the wheel. Do not by placing a soft cloth between the remove the retaining washers 3 on the screwdriver and the . wheel bolts. Remove wheel bolt caps 3 from wheel bolts. 176 Self-help, vehicle care

Picture no: 11643s.tif Picture no: 14724s.tif Picture no: 14762s.tif 2. Push the wheel bolt wrench 3 on as far 3. The jacking points are marked. 4. Set the jack 3 to the required height by as possible and slacken the wheel bolts On Meriva OPC and OPC Line and turning the lug by hand. Fit the jack arm half a turn. vehicles with sill trims, the jack 3 cannot at the front – or rear – so that the jack be used. It could damage the vehicle. claw (arrow in Fig.) grasps the vertical ridge and engages in the recess in the ridge. Ensure that the claw is properly positioned. Self-help, vehicle care 177

10. Before refitting the wheel trim, clean the wheel around the retaining clips. Valve symbol 3 on back of wheel trim must point towards valve on wheel. Align and refit wheel trim or wheel bolt caps 3. Alloy wheels 3: put hub cap on and engage, inserting pin on rear of hub cap into relevant hole in wheel. Alloy wheels with anti-theft lock 3: Put hub cap on. Insert and tighten anti- theft lock 3. 11. Stow removed wheel, tool kit and Picture no: 14763s.tif Picture no: 11647s.tif warning triangle in the luggage The edge of the jack base must be If the wheel bolts have retaining compartment 3 171. planted firmly and vertically in line with washers 3, they must not be removed. 12. Check the tyre pressure of the newly the contact point. 6. Change wheel. Notes on spare wheel mounted wheel. Raise vehicle by turning crank handle. 3 172. Notes on temporary spare wheel 13. Have the wheel bolt tightening 3 If this is not the case, carefully lower the 173. torque (110 Nm) checked. vehicle immediately and reposition the 7. Screw in the wheel bolts. Push the wheel 14. Replace the faulty tyre on the wheel jack. bolt wrench 3 on as far as possible and that was removed. 5. Unscrew the wheel bolts. tighten the wheel bolts slightly. 8. Lower vehicle. 9. Push the wheel bolt wrench 3 on as far as possible and tighten crosswise. Tightening torque is 110 Nm. 178 Self-help, vehicle care

Tyre repair kit 3 Minor damage to the tyre tread or sidewall can be repaired with the tyre repair kit. Do not remove the foreign body from the tyre. Tyre damage exceeding 4 mm or that is on the rim cannot be repaired with the tyre repair kit.

9 Warning Do not drive faster than 80 km/h. Do not use the temporary spare wheel for a lengthy period. Steering and handling may be affected. Picture no: 17919S.tif Picture no: 13639T.tif The tyre repair kit is in the stowage 3. Remove the electrical connection cable Important 3 181. compartment beneath the floor cover in and air hose from the stowage the luggage compartment. compartments on the underside of the In the event of a flat tyre: compressor. z Switch on the hazard warning flashers, 1. Remove bag containing tyre repair kit apply the hand brake, engage first gear from compartment. Carefully remove or reverse. parts from bag. z Erect warning triangle as specified. 2. Remove the compressor. Warning triangle 3 171. Self-help, vehicle care 179

Picture no: 15319t.tif Picture no: 15795t.tif Picture no: 15796t.tif 4. Screw the compressor air hose to the 7. Screw the filler hose to the tyre valve. 10. Switch on ignition. connection on the sealant bottle. 8. The switch on the compressor must be 11. Set the rocker switch on the compressor 5. Fit the sealant bottle in the retainer on set to §. to I. The tyre is filled with sealant. the compressor. 9. Plug the compressor connector into the 12. While the sealant bottle drains Set the compressor near the tyre in such accessory socket or the cigarette lighter (approx. 30 seconds) the pressure a way that the sealant bottle is upright. socket. For accessory sockets 3 78. indicator on the compressor briefly 6. Remove the valve cap from the defective points to 6 bar. Pressure then sinks tyre. again. 13. All of the sealant is pumped into the tyre. Afterwards, the tyre is filled with air. 14. The prescribed tyre pressure should be reached within 10 minutes. Tyre pressure 3 228. Switch off the compressor when the correct pressure is obtained. 180 Self-help, vehicle care

15. Detach the tyre repair kit. Screw the filler hose to the free connection on the sealant bottle. This prevents sealant leakage. Stow the tyre repair kit in the luggage compartment. 16. Wipe away any sealant spill with a cloth. 17. Fold away warning triangle, store in luggage compartment 3 171. 18. Stick the label indicating maximum permitted speed somewhere in the driver’s field of view. 19. Continue driving immediately to allow Picture no: 15797t.tif the sealant to distribute evenly Picture no: 15798t.tif If the prescribed tyre pressure is not throughout the tyre. Stop after If tyre pressure is more than 1.3 bar, obtained within 10 minutes, remove the approx. 10 km (no more than 10 adjust to the prescribed value. Repeat tyre repair kit. Move the vehicle one tyre minutes) and check tyre pressure. Screw the procedure until there is no more rotation. Reattach the tyre repair kit the compressor air hose directly onto pressure loss. the tyre valve (see Fig. 15798 T). and continue the filling procedure If the tyre pressure has dropped for 10 minutes. If the prescribed tyre below 1.3 bar, the vehicle must not be pressure is still not obtained, the tyre is used. Contact a workshop for too badly damaged. Seek the assistance. assistance of a workshop. 20. Stow tyre repair kit in luggage Drain excess tyre pressure with the compartment 3 178. button over the pressure indicator. Do not operate the compressor for more than 10 minutes, see "Important" 3 181. Self-help, vehicle care 181

Important The sealant can only be stored for approx. Electrical system The driving comfort of the repaired tyre is 4 years. After this time, the sealing Fuses severely affected, therefore have this tyre properties can no longer be guaranteed. Data on the replacement fuse must match replaced. Heed the expiration date on the sealant the data on the defective fuse. bottle. If the compressor makes abnormal noises In the vehicle there are two fuse boxes: in or heats up greatly, switch it off for at Replace the used sealant bottle. Dispose of the vehicle interior to the left of the least 30 minutes. the bottle as prescribed by applicable instrument panel, and in the engine bay to laws. the left in front of the windscreen. The integrated safety valve opens at a pressure of 7 bar. The compressor and sealant can be used from approx. -30 C. Protect the compressor from moisture and rain. The adapter on the bottom of the compressor can be used to pump up other items such as balls, air beds, inflatable dinghies and so on. Unscrew the air hose and pull the adapter out. 182 Self-help, vehicle care

Picture no: 14725s.tif Picture no: 12892j.tif Picture no: 14211s.tif Keep spare fuses in the fuse box lid (shown Slot fuse-gripping tool onto fuse and Fuses and the most important in yellow in the Fig.). Open lid 3 182. withdraw it. circuits they protect Before replacing a fuse, turn off the Some functions are protected by several Fuse box in passenger compartment respective switch and the ignition. fuses. Disengage fuse box cover at bottom and A blown fuse can be recognised by its There may be fuses inserted with no remove. melted wire. Do not replace the fuse until function. No. Circuit the cause of the fault has been remedied. Always use fuses with the correct current 1 Central control unit To help in replacing fuses, there is a special value. This is shown on each fuse, and is 2 Immobiliser, hazard warning fuse-gripping tool in the fuse box 3. also indicated by the fuse colour and the lamps, exterior lighting plug-in location in the fuse box. 3 Headlamp washer system Different versions of fuses are used. Self-help, vehicle care 183

No. Circuit No. Circuit No. Circuit 4 Infotainment system, diesel engine 17 – 33 Central control module, immobiliser, control indicators 5 – 18 Adaptive Forward Lighting 34 Windscreen wipers 6 – 19 Central locking system 35 Interior lighting, interior mirror, 7 Starter, diesel engine: engine 20 Interior lighting, reading lamp information display controller 21 Windscreen washer system 36 Brake light, ABS, ESP®Plus 8 Horn 22 Rear electric window 37 Cigarette lighter, auxiliary heater 9 Fuel injection system, fuel pump, 23 Tilt/slide sun roof, skylight roof 38 Seat heater (left) stationary heater 24 Anti-theft alarm system 39 Seat heater (right) 10 Turn signal lamps 25 Rear window wiper 40 Adaptive Forward Lighting, 11 Infotainment system, Information 26 Ignition system, engine electronics display, Infotainment system automatic headlamp range 27 Engine control, airbag, ESP®Plus adjustment 12 Heated rear window, exterior mirrors 28 Air conditioning system 41 Reversing lamps 13 Central locking, anti-theft alarm 29 Front left electric window system 30 – 14 Engine control 31 Engine control, Petrol engine: Z 17 DTH engine Diesel engine: 32 Front right electric window 15 Engine control unit, Z 17 DTH engine 16 Accessory socket, cigarette lighter 184 Self-help, vehicle care

Picture no: 14436s.tif Picture no: Picture no: 14213s.tif No. Circuit No. Circuit Fuse box in engine compartment 42 Engine cooling, lighting 51 Left dipped beam: The fuse box is at the front left of the engine compartment. 43 Left parking lamp Xenon headlamp Halogen headlamp 44 Right parking lamp 9 Warning 52 Right dipped beam: 45 Fog tail lamp Xenon headlamp Turn off engine before opening fuse 46 Fog lamps Halogen headlamp box, risk of injury. 47 Towing equipment, accessory 53 Sun roof, electric windows, radio socket Disengage cover of fuse box from lug and 54 Main beam (left) lift off. 48 Diesel filter heater 55 Main beam (right) Some circuits may be protected by several 49 – 56 – fuses. 50 Diesel filter heater Self-help, vehicle care 185

Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with your bare hands. Replace the bulb, checking that the data on the base matches that of the defective bulb. To replace a bulb, pull off the relay box on the left side. On the right side, pull off the air hose to the air filter.

Picture no: 14214s.tif Picture no: 16085s.tif The following fuses are Maxi fuses. Halogen headlamp system No. Circuit Headlamp system has separate bulbs for dipped beam 1 (bottom bulbs) and main 1 Interior fan beam 2 (top bulbs). 2 Power steering 3 ABS 4 Easytronic diesel preheating system 5 Heated rear window 6 Engine cooling 7 Starter 8 Engine cooling 186 Self-help, vehicle care

Picture no: 16086s.tif Picture no: 16087s.tif Picture no: 16088s.tif Dipped beam 3. Press the bulb down in the holder. 5. Detach plug connector from bulb base. 1. Open bonnet and engage support. 4. Remove bulb with connector from 6. Attach connector to new bulb. 2. Rotate the cap anticlockwise and reflector housing. 7. Insert the bulb with connector so that remove. the lug engages in the recess in the reflector. 8. Place headlamp protective cover in position and close. Self-help, vehicle care 187

Picture no: 16089s.tif Picture no: 16090s.tif Picture no: 16091s.tif Main beam 3. Detach plug connector from bulb. 5. Remove bulb from reflector housing. 1. Open bonnet and engage support. 4. Disengage spring wire clip from 6. When fitting the new bulb, insert lugs in 2. Rotate the cap anticlockwise and retaining lugs by moving it forwards the reflector recesses. remove. and swivel it aside. 7. Engage spring wire clip, plug connector onto bulb. 8. Place headlamp protective cover in position and close. 188 Self-help, vehicle care

Halogen headlamp system 3, Adaptive Forward Lighting (AFL) Halogen headlamp system for dipped and main beam in combination with curve lighting and cornering light.

9 Warning The xenon headlamps work with very high electrical voltage. Do not touch. Have bulbs changed by a workshop.

Picture no: 14222s.tif Picture no: 14219s.tif Xenon headlamp system Main beam Headlamp system has separate bulbs for 1. Open bonnet and engage support. dipped beam 1 (bottom bulbs) and main 2. Remove headlamp protective cover. beam 2 (top bulbs). Dipped beam

9 Warning The xenon headlamps work with very high electrical voltage. Do not touch. Have bulbs changed by a workshop. Self-help, vehicle care 189

Picture no: 14220s.tif Picture no: 14221s.tif Picture no: 16089s.tif 3. Detach plug connector from bulb. 5. Remove bulb from reflector housing. Parking lamps 4. Disengage spring wire clip from 6. When fitting the new bulb, insert lugs in 1. Open bonnet and engage support. retaining lug and swivel upward. the reflector recesses. 2. Rotate the main beam headlamp cap 7. Engage spring wire clip, plug connector anticlockwise and remove. onto bulb. On vehicles with Xenon headlamps 3, 8. Place headlamp protective cover in remove headlamp cover cap 3 188, position and close. Fig. 14219 S. 190 Self-help, vehicle care

Picture no: 16092s.tif Picture no: 16093s.tif Picture no: 16094s.tif 3. Push side lugs of parking lamp holder 4. Remove bulb from holder. Front indicator lamps together and remove holder from 5. Insert new bulb. 1. Open bonnet and engage support. reflector. 6. Insert bulb socket in reflector. 2. Rotate left turn signal lamp bulb carrier and disengage. 7. Place headlamp protective cover in position and close. Self-help, vehicle care 191

7. Rotate bulb carrier to right as far as it will go. Side turn signal lamps Have bulb replacement carried out by a workshop. Fog lamps 3 Have bulb replacement carried out by a workshop.

Picture no: 16095s.tif Picture no: 17953S.tif 3. Remove bulb mounting from reflector. Tail lamps 4. Detach bulb from bulb mounting. 1. Unscrew the four screws from the bulb housing using a screwdriver 3. 5. Insert new bulb in bulb holder. 2. Pull lamp housing, reflector and tail fog 6. Insert new bulb so that the two lugs on lamp out of retainers to rear. the bulb mounting engage in the recesses in the reflector. 192 Self-help, vehicle care

Picture no: 17954S.tif Picture no: 17955S.tif Picture no: 17956s.tif 3. Disengage the plug of the main bulb 5. Slacken both screws on the back of the Bulbs in main bulb carrier: mounting by pressing (arrow in Fig.) and main bulb mounting. Press the catches 1 = Turn signal lamp pull from bulb mounting. of the bulb mounting together and 2 = Brake lamp bulb 3 remove the bulb mounting. 4. Disengage lug of fog tail lamp plug 3 = Tail lamp (arrow in Fig.) and remove. 4 = Reversing light Remove bulb from holder. Self-help, vehicle care 193

Picture no: 17957s.tif Picture no: 17900s.tif Picture no: 14232s.tif Fog tail lamp bulb: Rotate bulb Number plate lamp 2. Rotate bulb holder to left and mounting anticlockwise and disengage. 1. Insert screwdriver 3 vertically on right- disengage. Remove bulb from holder. hand side of bulb housing, exert pressure towards the right and disengage spring. 6. Fit new bulbs. Click bulb mounting into Remove the bulb housing downwards. housing. 7. Connect both plugs. Insert bulb housing with retaining pins in body and fasten with screws. 194 Self-help, vehicle care

5. Engage bulb holder by rotating right in lamp housing. Insert lamp housing and engage.

Picture no: 14233s.tif Picture no: 11669s.tif 3. Remove bulb from holder. Courtesy lamps 4. Insert new bulb. Front courtesy lamp, reading lamps 3 1. Unclip the scatter disc on the housing at the point shown. Self-help, vehicle care 195

Rear courtesy lamp, rear reading lamps 3 Have bulb replacement carried out by a workshop.

Picture no: 11670s.tif Picture no: 12927j.tif 2. Remove bulb from holder. Glove compartment lamp 3, luggage 3. Insert new bulb. compartment lamp 1. Prise the lamp out with a screwdriver 3 4. Mount lens and engage in position. and remove. 196 Self-help, vehicle care

Vehicle care Bird droppings, dead insects, resin, pollen When caring for your vehicle, observe all and the like should be cleaned off national environmental regulations, immediately, as they contain aggressive particularly when washing it. constituents which can cause paint damage. Regular, thorough care helps to improve the appearance of your vehicle and If using a car wash, comply with the car maintain its value over the years. It is also wash operator’s instructions. The prerequisite for warranty claims for any windscreen wipers and rear window wiper paint or corrosion damage. The following must be switched off. Remove antenna 3 pages contain tips for vehicle care which, if and roof rack 3. Stand on the door sill to used properly, will help combat the reach them more easily. unavoidable damaging effects of the If you wash your vehicle by hand, make environment. sure that the insides of the wings are also Washing thoroughly rinsed out. Picture no: 12928j.tif The paintwork of your vehicle is exposed to Clean edges and folds on opened doors 2. Press bulb slightly towards spring clip environmental influences. Wash and wax and flaps as well as the areas they cover. and remove. your vehicle regularly. When using Thoroughly rinse off and leather-off the 3. Insert new bulb. automatic car washes, select a programme vehicle. Rinse leather frequently. Use that includes waxing. 4. Insert lamp in opening and engage in separate leathers for paint and window position. surfaces: remnants of wax on the windows Instrument illumination, Information will impair vision. display illumination 3 Do not use hard objects to remove spots of Have bulb replacement carried out by a tar. Use tar removal spray on painted workshop. surfaces. Self-help, vehicle care 197

Polishing and waxing Exterior lights The instrument panel should only be Wax the vehicle regularly (by the time the Headlamp and other lamp covers are cleaned using a soft damp cloth. water no longer beads at the latest). made of plastic. Do not use any caustic Clean fabric upholstery with a vacuum Otherwise, the paintwork will dry out. agents, do not use an ice scraper, and do cleaner and brush. Remove stains with an Polishing is necessary only if the paint has not clean them when dry. upholstery cleaner. become dull or if solid deposits have Plastic and rubber parts Clean seat belts with lukewarm water or become attached to it. Plastic and rubber parts can be cleaned interior cleaner. Paintwork polish with silicone forms a with the same cleaner as used to clean the protective film, making waxing body. Use interior cleaner if necessary. Do Caution unnecessary. not use any other agent. Avoid solvents and petrol in particular. Do not use high- Close Velcro fasteners as open Velcro Plastic body parts should not be treated pressure jet cleaners. fasteners on clothing could damage with wax and polish. Interior and upholstery seat upholstery. Wheels and tyres Only clean the vehicle interior, including Do not use high-pressure jet cleaners. the instrument panel fascia and panelling, Clean wheels with a pH-neutral wheel with a dry cloth or interior cleaner. cleaner. Wheels are painted and can be treated with the same agents as the body. Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop. 198 Self-help, vehicle care

Windows and blades Locks Underbody Use a soft lint-free cloth or chamois leather The locks are lubricated with a high-quality Some areas of the vehicle underbody have together with window cleaner and insect locking cylinder grease in the factory. Only a PVC undercoating while other critical remover. use de-icer in urgent cases, since it has a areas have a durable protective wax When cleaning the rear window, make sure de-greasing effect and affects the coating. the heating element inside the window is operation of the locks. Have the locks re- After the underbody is washed, check the not damaged. greased in a workshop after using de-icer. underbody and have more protective wax For mechanical removal of ice, use a sharp- Engine compartment applied if necessary. edged ice scraper. Press the scraper firmly Look after areas in the engine Bitumen/rubber materials could damage against the glass so that no dirt can get compartment that are painted in the same the PVC coating. Have underbody work under it and scratch the glass. colour as the vehicle like any other carried out by a workshop. paintwork. Clean smearing wiper blades with a soft Before and after winter, wash the cloth and window cleaner. It is advisable to wash the engine underbody and have the protective wax compartment before and after winter and coating checked. preserve it with wax. Cover alternator and brake fluid reservoir with plastic sheets Towing equipment before washing the engine. Do not clean the coupling ball bar with a steam-jet or high-pressure jet cleaner. When washing the engine with a steam-jet cleaner, do not direct the steam jet at components of the Anti-lock Braking System 3, the automatic air conditioning system 3 or the belt drive and its components. After an engine wash, have all engine room components preserved thoroughly by a workshop using protective wax. Do not use high-pressure jet cleaners. Service and maintenance 199

Service and Scheduled maintenance Service schedule These service intervals apply only under The service schedule applies in the maintenance normal driving conditions. If conditions are following countries: Andorra, Austria, more arduous 3 206 Belgium, Cyprus, Czech Republic, Service interval display 3 208. Denmark, Estonia, Finland, France, Germany, Great Britain, Greece, European service intervals Greenland, Hungary, Iceland, Ireland, Italy, Every 30 000 km or annually, whichever Latvia, Lithuania, Luxembourg, Malta, Scheduled maintenance ...... 199 occurs first. Netherlands, Norway, Poland, Portugal, Service schedule ...... 199 International service intervals Slovakia, Slovenia, Spain, Sweden, Additional service work...... 206 Every 15 000 km or annually, whichever Switzerland. Recommended fluids and lubricants .. 206 occurs first. The international service schedule applies Inspection system ...... 208 in all other countries. Genuine Opel Parts and Accessories .. 209 Validation Service is validated using the spaces Performing work ...... 209 provided in the Service and Warranty Engine oil...... 210 Booklet. The date of service and kilometre Diesel fuel filter ...... 212 reading are added, stamped and signed Coolant...... 212 by the service workshop. Brakes...... 213 Ensure that the Service and Warranty Brake fluid ...... 214 Booklet is filled in correctly - an Windscreen wiper replacement...... 215 uninterrupted service history is important Windscreen and headlamp washer when making guarantee or goodwill systems 3...... 215 claims, and is also an advantage when Battery...... 216 selling the vehicle on. Protecting electronic components ..... 216 Laying the vehicle up for a long period of time...... 217 Putting the vehicle back into service... 217 200 Service and maintenance

Service schedule Europe Service work after year1) 1 2 3 4 5 km (x1000)1) 30 60 90 120 150 Carry out a visual check of all warning lamps, lighting and signalling devices, xxxxx check steering and ignition locks Remote control: replace batteries (check spare key) every 2 years Check windscreen wipers, windscreen washer and headlamp washer systems, adjust if xxxxx necessary. Check coolant and antifreeze (bright orange) levels2), adjust if necessary, note xxxxx antifreeze temperature in Service and Warranty Booklet (validation fields). Check water-carrying hoses for leaks and make sure that they are secure. xxxxx Check break fluid level2), top up if necessary. x x x Check that the battery terminals and lugs are secure xxxxx Vehicle system check using TECH 2 xxxxx Replace pollen filter or active charcoal filter x x ⊕o If the air is particularly polluted, full of dust or sand or pollen, if the air conditioning Discussion between customer / Opel Partner system smells Replace air cleaner element every 4 years/60 000 km ⊕ Replace spark plugs every 4 years/60 000 km Make a visual check of the ribbed belt x x ⊕ Replace ribbed belt every 10 years/150 000 km Z 13 DT, Z 13 DTJ, Z 17 DTH, Z 17 DT, Z 17 DTR. ⊕ Check valve clearance, adjust if necessary every 10 years/150 000 km Z 16 LET, Z 16 XEP, Z 17 DTH, Z 17 DT, Z 17 DTR

1) Depending on what occurs first. 2) If the loss is too great or there are leaks, carry out remedial work in agreement with the customer. ⊕ additional work. o The intervals are shorter where driving conditions are more arduous or country-specific. Service and maintenance 201

Service work after year1) 1 2 3 4 5 km (x 1000)1) 30 60 90 120 150 ⊕ Replace timing belt and tension pulley Z 18 XE every 6 years/90 000 km Z 17 DTH every 10 years/90 000 km Z 16 LET, Z 16 XEP, Z 17 DTR, Z 17 DTR every 10 years/150 000 km Change engine oil and replace filter xxxxx ⊕o Drain water from fuel filter, diesel (if the air humidity is high or the fuel of lower quality)xxxxx Replace fuel filter and drain water, diesel (grade EN 590) xx Z 13 DTJ, Z 17 DTH Replace fuel filter, petrol (grade EN 228), outer Z 16 LET every 4 years/60 000 km Check handbrake, adjust if necessary (unladen wheels); carry out a visual check of xx wheel suspension and suspension front and rear, brake lines, brake pressure hose, fuel lines and exhaust system Check external bodywork / underseal, note any damage in the Service and Warranty x xxxx Booklet. ⊕o Carry out a visual check on the front and rear wheel brakes2) xx Annual service check if the annual distance travelled is greater than 20 000 km. Carry out a visual check of the engine, transmission (AT, MT), check air conditioning xxxxx compressor for leaks2)

1) Depending on what occurs first. 2) If the loss is too great or there are leaks, carry out remedial work in agreement with the customer. ⊕ additional work. o The intervals are shorter where driving conditions are more arduous or country-specific. 202 Service and maintenance

Service work after year1) 1 2 3 4 5 km (x1000)1) 30 60 90 120 150 ⊕o Remove brake drum, clean, carry out visual check every 4 years/60 000 km Visually inspect steering system boots, track rods, final drive xxxxx Check track rod end and supporting ball joint xxxxx ⊕ Change brake and clutch fluids (manual transmission automated) every 2 years Loosen wheel mountings and tighten to 110 Nm Grease or apply oil to bolt taper when fitting. Check tyre condition and pressure (including spare wheel), correct if necessary. xx If there is a tyre inflation system, check that the set is complete and the use-by date is still valid. Replace sealant bottle every four years. ⊕ Annual service check if the annual distance travelled is greater than 20 000 km. Visually check the first aid kit (that it is where it should be, that it is undamaged and that every 2 years the use by date is still valid), lashing eyes and warning triangle Check headlamp settings (including auxiliary headlamps), adjust if necessary x x Lubricate door hinges, check arms, cylinder lock, door latch, bonnet catch, rear panel xx hinge Test run, final check (check steering and ignition lock, instrument and warning lamps, xxxxx entire brake system, steering, air conditioning system, engine, bodywork and chassis, reset service/interval display with TECH 2. ⊕ Germany only: carry out emissions check, main inspection First time after three years, then every 2 years If used commercially to transport passengers, taxis, ambulances, hire etc annually

1) Depending on what occurs first. ⊕ additional work. o The intervals are shorter where driving conditions are more arduous or country-specific. Service and maintenance 203

International service schedule Service work after year1) 1 2 3 4 5 km (x 1000)1) 15 30 45 60 75 Carry out a visual check of all warning lamps, lighting and signalling devices, xxxxx check steering and ignition locks Remote control: replace batteries (check spare key) every 2 years Check windscreen wipers, windscreen washer and headlamp washer systems, adjust if xxxxx necessary. Check coolant and antifreeze (bright orange) levels2), adjust if necessary, note xxxxx antifreeze temperature in Service and Warranty Booklet (validation fields). Check water-carrying hoses for leaks and make sure that they are secure. xxxxx Check break fluid level2), top up if necessary. x x x Check that the battery terminals and lugs are secure xxxxx Vehicle system check using TECH 2 xxxxx Replace pollen filter or active charcoal filter x x ⊕o If the air is particularly polluted, full of dust or sand or pollen, if the air conditioning Discussion between customer / Opel Partner system smells Replace air cleaner element every 4 years/60 000 km ⊕ Replace spark plugs every 4 years/60 000 km Make a visual check of the ribbed belt x x ⊕ Replace ribbed belt every 10 years/150 000 km Z 13 DT, Z 13 DTJ, Z 17 DTH, Z 17 DT, Z 17 DTR. ⊕ Check valve clearance, adjust if necessary every 10 years/150 000 km Z16 LET, Z 16 XEP, Z 17 DTH, Z 17 DT, Z 17 DTR

1) Depending on what occurs first. 2) If the loss is too great or there are leaks, carry out remedial work in agreement with the customer. ⊕ additional work. o The intervals are shorter where driving conditions are more arduous or country-specific. 204 Service and maintenance

Service work after year1) 1 2 3 4 5 km (x 1000)1) 15 30 45 60 75 ⊕ Replace timing belt and tension pulley Z 18 XE every 6 years/90 000 km Z 17 DTH every 10 years/90 000 km Z 16 LET, Z 16 XEP, Z 17 DTR, Z 17 DTR every 10 years/150 000 km Change engine oil and replace filter xxxxx ⊕o Drain water from fuel filter, diesel (if the air humidity is high or the fuel of lower quality)xxxxx Replace fuel filter and drain water, diesel (grade EN 590) xx Z 13 DTJ, Z 17 DTH Replace fuel filter, petrol (grade EN228), outer Z 16 LET every 4 years/60 000 km Check handbrake, adjust if necessary (unladen wheels); carry out a visual check of xx wheel suspension and suspension front and rear, brake lines, brake pressure hose, fuel lines and exhaust system Check external bodywork / underseal, note any damage in the Service and Warranty x xxxx Booklet. ⊕o Carry out a visual check on the front and rear wheel brakes2) xx Annual service check if the annual distance travelled is greater than 20 000 km. Carry out a visual check of the engine, transmission (AT, MT), check air conditioning xxxxx compressor for leaks2)

1) Depending on what occurs first. 2) If the loss is too great or there are leaks, carry out remedial work in agreement with the customer. ⊕ additional work. o The intervals are shorter where driving conditions are more arduous or country-specific. Service and maintenance 205

Service work after year1) 1 2 3 4 5 km (x 1000)1) 15 30 45 60 75 ⊕o Remove brake drum, clean, carry out visual check every 4 years/60 000 km Visually inspect steering system boots, track rods, final drive xxxxx Check track rod end and supporting ball joint xxxxx ⊕ Change brake and clutch fluids (manual transmission automated) every 2 years Loosen wheel mountings and tighten to 110 Nm Grease or apply oil to bolt taper when fitting. Check tyre condition and pressure (including spare wheel), correct if necessary. xx If there is a tyre inflation system, check that the set is complete and the use-by date is still valid. Replace sealant bottle every four years. ⊕ Annual service check if the annual distance travelled is greater than 20 000 km. Visually check the first aid kit (that it is where it should be, that it is undamaged and that every 2 years the use by date is still valid), lashing eyes and warning triangle Check headlamp settings (including auxiliary headlamps), adjust if necessary x x Lubricate door hinges, check arms, cylinder lock, door latch, bonnet catch, rear panel xx hinge Test run, final check (check steering and ignition lock, instrument and warning lamps, xxxxx entire brake system, steering, air conditioning system, engine, bodywork and chassis, reset service/interval display with TECH 2.

1) Depending on what occurs first. ⊕ additional work. o The intervals are shorter where driving conditions are more arduous or country-specific. 206 Service and maintenance

Additional service work With hard driving conditions it might be Recommended fluids and Additional work ⊕ necessary to carry out certain service work lubricants Additional work is not always necessary at more frequently than the scheduled Only use products which have been tested each service, but can be carried out at the intervals. and approved. Damage caused by using same time as a regular service. We recommend seeking technical advice operating materials which have not been The cost of this type of work is not included with regard to servicing requirements for approved is not covered by the guarantee. in the charge for a regular service and will your particular driving circumstances. be invoiced separately. It is, however, more 9 Warning cost-effective to have this work done at the Operating materials are dangerous and same time as a scheduled service rather must be handled carefully. If swallowed, than have it done separately. seek medical help immediately. Do not Hard driving conditions o breath in fumes and avoid contact with Conditions are considered hard when one the skin. Keep away from children. or more of the following situations occurs These materials are forbidden to more frequently: contaminate waste water, surface z cold start, water, groundwater or soil. Dispose of empty containers correctly. Always z stop and go, remember that operating materials are z caravan/trailer towing, dangerous. z inclines or steep climbs, z poor road conditions, z sand and dust, z extreme temperature fluctuations. Police vehicles, taxis and driving school vehicles are classified as being subjected to hard driving conditions. Service and maintenance 207

Engine oil Engine oil: top up Engine oil additives Engine oil is graded by quality and Oils from different manufacturers and The use of motor oil additives can lead to viscosity. When choosing an engine oil, the different brands of oil can be mixed as long damage and will invalidate the guarantee. quality grade is more important than the as the grades (quality and viscosity) are Engine oil viscosity viscosity. the same. Only use engine oils with viscosity The new GM-Dexos 2 engine oil grade is Not all the engine oils available on the grades 0W-30, 0W-40, 5W-30 or 5W-40. currently the highest grade. If it is not market are of a suitable quality. Always The SAE viscosity grading system indicates available, the other engine oil grades that check that the required specification and the oil’s flowability. Oil is more viscous are listed must be used. classification are given on the cans. when cold than when warm. Engine oil grade for the European If an engine oil of the required grade is not Multigrade oil has two numbers. The first, service plan available, a maximum of 1 litre of ACEA followed by a W, indicates the viscosity at GM-Dexos 2 = Petrol and A3/B4 or A3/B3 oil may be used (just once low temperatures and the second indicates diesel engines between oil changes). The viscosity must the viscosity at high temperatures. comply with the requirements. GM-LL-A-025 = Petrol engines GM-LL-B-025 = Diesel engines It is forbidden to use engine oil of grades ACEA A1/B1 and A5/B5. Under Engine oil grade for the International certain circumstances, these oils can cause service plan long-term damage to the engine. GM-Dexos 2 = Petrol and diesel engines GM-LL-A-025 = Petrol engines GM-LL-B-025 = Diesel engines ACEA-A3 = Petrol engines ACEA-B4 = Diesel engines without diesel particle filter (DPF) ACEA-C3 = Diesel engines with DPF 208 Service and maintenance

The service interval display takes account Further information on maintenance and of off-the-road periods during which the the inspection system can be found in the battery is disconnected. Service and Warranty Booklet, which is in Flexible service interval 3 the glove compartment. The length of the service intervals is based Have maintenance work – and repair work on several parameters stemming from on the body and the equipment – carried usage. For this reason, various out professionally by a workshop. We engine-specific data is continually recommend using your Opel partner, who gathered and is used to calculate the has excellent knowledge of Opel vehicles remaining distance until the next service. and has the necessary special tools and If the remaining distance is less up-to-date service instructions from Opel. than 1500 km, InSP is displayed with a It is particularly advisable to use an Opel remaining distance of 1000 km when the Partner during the warranty period in order ignition is switched on and off. If less to prevent loss of warranty. Further Picture no: 18602s.tif than 1000 km remains, InSP is displayed for information can be found in the Service Inspection system several seconds. Have the next service and Warranty Booklet. In order to guarantee economical and safe performed by a workshop within one week Separate anti-corrosion service vehicle operation and to maintain the or 500 km (whichever occurs first). Have this work done at the intervals given value of your vehicle, it is of vital Display of remaining distance: in the Service and Warranty Booklet. importance that all maintenance work is carried out at the proper intervals. 1. Switch off ignition. Fixed service interval 2. Briefly press the trip odometer reset When service is due, InSP appears in the button. The odometer reading is shown. odometer display for 3. Press and hold the reset button for about approximately 10 seconds when the 2 seconds. InSP and the remaining ignition is switched on. Have the next distance are displayed. service performed by a workshop within one week or 500 km (whichever occurs first). Service and maintenance 209

Genuine Opel Parts and Accessories We recommend that you use "Genuine Opel Parts and Accessories" and conversion parts released expressly for your vehicle type. These parts have undergone special tests to establish their reliability, safety and specific suitability for Opel vehicles. Despite continuous market monitoring, we cannot assess or guarantee these attributes for other products, even if they have been granted approval by the relevant authorities or in some other form. "Genuine Opel Parts and Accessories" and conversion parts approved by Opel can be Picture no: 17922S.tif Picture no: 14234s.tif obtained from your Opel Partner, who can Performing work 9 Warning provide expert advice on permitted To avoid injury from moving parts and technical changes and ensure correct cables conducting ignition voltage, only The ignition system 3 and Xenon installation. carry out engine compartment checks headlamps 3 use extremely high (e. g. checking brake fluid or engine oil voltage. Do not touch. level) when the ignition is switched off. To aid identification, the caps to be 9 Warning removed for topping up engine oil, coolant and washer fluid and the dipstick handle Only perform engine compartment may be coloured yellow. checks when the ignition is off. The cooling fan may start operating even if the ignition is off. 210 Service and maintenance

Picture no: 16486s.tif Picture no: 16487s.tif Picture no: 17903s.tif Engine oil Check with the vehicle on a level surface. Pull out the dipstick, wipe it clean, insert it In vehicles fitted with engine oil level The engine must be at operating to the stop on the handle, pull out and read monitoring 3, the engine oil level is temperature and switched off for at least the engine oil level. checked automatically 3 85. We 5 minutes. Push the dipstick in as far as it will go and recommend checking the engine oil level twist it by half a turn. before embarking on long journeys. Different dipsticks are used depending on engine variant. When the engine oil level has dropped to the MIN mark, top up engine oil. Service and maintenance 211

Picture no: 15972s.tif Picture no: 14238s.tif Picture no: 17902s.tif We recommend that you use the same The engine oil level must not exceed The amount filled must be between the engine oil as was used the last time it was the MAX mark on the dipstick. MIN and MAX marks 3 230. topped up. Fit the cap on straight and tighten it. Caution If there is too much engine oil, the excess must be drained or suctioned out. 212 Service and maintenance

Diesel fuel filter Coolant On the event of engine oil change, have The coolant provides anti-freeze fuel filter checked for possible water protection down to approx. -28 C. residue by a workshop. Caution Illumination of A indicates water in the fuel filter 3. Only use approved anti-freeze. Have fuel filter checked at shorter intervals Coolant additives used to give if the vehicle is subjected to extreme additional protection against corrosion operating conditions such as high humidity and prevention against small leaks can (primarily in coastal areas), extremely high lead to functional problems. No liability or low outside temperatures and is accepted for damage caused by using substantially varying daytime and coolant additives. night-time temperatures. .

9 Picture no: 17905s.tif Warning Antifreeze and corrosion protection Antifreeze is a danger to health; it must Have the concentration of the radiator therefore be kept in the original contents tested by a workshop before container and out of the reach of winter starts. The amount of antifreeze children. must provide protection down to approx. -28 C. A lower antifreeze concentration will reduce the amount of protection from frost and corrosion. Add antifreeze if necessary. If coolant loss is topped up with water, have concentration checked and add antifreeze if necessary. Service and maintenance 213

Top up with anti-freeze. If no anti-freeze is Brakes available, fill with clean tap water or A screeching noise indicates that the brake distilled water. Have the anti-freeze lining is at its minimum thickness. concentration checked. Continued driving is possible. Have the Have the cause of coolant loss rectified by brake lining replace as soon as possible. a workshop. Once new brake lining is fitted, do not brake unnecessarily hard for the Caution first 200 km. Too low a coolant level can cause engine damage.

Fit the cap on straight and tighten it.

Picture no: 17904s.tif Coolant level In a closed cooling system, there is hardly any loss. If the cooling system is cold, the coolant should lie above the KALT/COLD mark. Top up if the level is low.

9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the overpressure slowly. 214 Service and maintenance

When topping up, ensure maximum Brake fluid change cleanliness as contamination of the brake Brake fluid is hygroscopic, i.e. it absorbs fluid can lead to function problems in the water. If the brakes become hot, such as braking system. when driving on long downhill stretches, Only use approved high performance vapour bubbles can occur in the water, brake fluids. Only use brake fluid DOT4. which can have an extremely adverse effect on braking power (depending on the After correcting the brake fluid level, have proportion of water). the cause of the loss of brake fluid remedied by a workshop. Keep to the specified intervals. 9 Warning Have the brake fluid change performed by a workshop. Please comply with the legal environmental and health Picture no: 14765s.tif regulations – concerning the disposal Brake fluid of brake fluid. 9 Warning Brake fluid is poisonous and corrosive. Do not allow it to come into contact with eyes, skin, fabrics or painted surfaces. The brake fluid level must be between the MIN and the MAX marks. Service and maintenance 215

Picture no: 13328j.tif Picture no: 9392t.tif Picture no: 14245s.tif Windscreen wiper replacement Wiper blade on the rear window 3 Windscreen and headlamp Wiper blades on the windscreen Lift wiper arm. Disengage wiper blade as washer systems 3 Lift wiper arm. Move release lever and shown in illustration and remove. Reservoir for windscreen washing system detach wiper blade. and rear window washing system in engine compartment beneath the right-hand windscreen wiper. 216 Service and maintenance

Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the negative terminal of the vehicle battery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery. Protecting electronic components In order to prevent faults in electronic components in the electrical system, never connect or disconnect battery with engine running or ignition switched on. Never start engine with battery disconnected, e.g. when starting using jump leads. Picture no: 14246s.tif Picture no: 13488a.tif In vehicles with headlamp washing Battery To avoid damaging the vehicle, do not make any modifications to the electrical system 3 Opening for refilling is in engine The vehicle battery is maintenance-free. compartment behind the right-hand system, e. g. connecting additional headlamp. Batteries do not belong in household consumers or tampering with electronic waste. They must be disposed of at an control units (chip tuning). Fill with clean water mixed with cleaner appropriate recycling collection point. and anti-freeze. The retrofitting of electrical or electronic 9 Warning Make sure there is sufficient anti-freeze accessories may subject the battery to protection. Electronic ignition systems generate very additional loading and cause it to become high voltages. Do not touch the ignition When closing the reservoir, press the lid discharged. Please seek advice concerning system; high voltage can be fatal. firmly over the beaded edge all the way the technical options, such as installing a round. more powerful battery. Service and maintenance 217

Laying the vehicle up for a long z Park vehicle in dry and well ventilated Putting the vehicle back into period of time place. Select first gear or reverse gear, service If the vehicle is to be laid up for several and with manual transmission Perform the following work before 3 months, the following work should be automated move selector lever to recommissioning the vehicle: undertaken to prevent damage. middle position before switching ignition off. Use wedges or something similar to z Connect the clamp to the negative z Wash and wax the vehicle 3 196. prevent vehicle from rolling. terminal of the vehicle battery. z Have the wax in the engine z Do not apply hand brake. z Check tyre pressure 3 228. compartment and underbody checked. z Disconnect the clamp from the negative z Top up windscreen washer system 3 215. z Clean and preserve rubber seals. terminal of the vehicle battery. z Check engine oil level 3 210. z Change engine oil. z Check coolant level 3 213. z Check antifreeze and corrosion z Fit the number plate if necessary. protection 3 212. z Check coolant level, add antifreeze if necessary 3 213. z Empty windscreen washer system and headlamp washer system. z Increase tyre pressure to value given for full load 3 228. 218 Technical Data

Technical Data Vehicle data The technical data is determined in accordance with European Community standards. We reserve the right to make modifications. Specifications in the vehicle documents always have priority over those given in this manual.

Vehicle data...... 218 Engine data...... 220 Picture no: 14247s.tif Performance...... 222 The identification plate is affixed to the front right door frame. Fuel consumption, CO2 -emissions..... 224 Weights, payload and roof load...... 226 Tyres ...... 228 Capacities ...... 230 Dimensions...... 231 Mounting dimensions of towing equipment 3...... 232 Technical Data 219

Engine identifier and engine number: marked on left-hand side of engine in engine block.

Picture no: 13329j.tif Picture no: 14249s.tif Information on identification plate: The vehicle identification number is stamped on the identification plate and on 1 Manufacturer the right side of the floor of the vehicle 2 Type approval number under a cover between the front door and 3 Vehicle identification number the seat. 4 Gross vehicle weight rating The vehicle identification number may be 5 Permissible gross train weight attached to the instrument panel. 6 Maximum permissible front axle load 7 Maximum permissible rear axle load 8 Vehicle-specific or country-specific data 220 Technical Data

Engine data Sales designation 1.4 TWINPORT 1.6 TWINPORT 1.8 OPC Engine identifier code Z 14 XEP Z 16 XEP Z 18 XE Z 16 LET Number of cylinders 4 4 4 4 Piston displacement [cm3] 1364 1598 1796 1598 Brake horse power [kW/bhp] 66 77 92 132 at rpm 5600 6000 6000 5500 Torque [Nm] 125 150 165 230 at rpm 4000 3900 4600 2200-5500 Fuel type1) Petrol Petrol Petrol Petrol Octane rating RON2) recommended 95 (P)3) 95 (P)3) 95 (P)3) 95 (S)3)5) possible 98 (PP)3) 98 (PP)3) 98 (PP)3) 98 (SP)3) possible 91 (R)3)4) 91 (R)3)4) 91 (R)3)4) –6) Max. permissible engine speed, continuous operation (rpm) approx. 6200 6500 6500 6500 Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6

1) Standard quality fuels, e.g. unleaded DIN EN 228. 2) Standard quality fuels: N = Normal, S = Super, SP = Super Plus; bold type: recommended fuel. 3) Knock control system automatically adjusts ignition timing according to type of fuel used (octane number). 4) Use of 91 RON fuel - lower power and torque and increased fuel consumption. 5) Use of 95 RON fuel - lower power and torque and increased fuel consumption. 6) 91 RON fuel must not be used. Technical Data 221

Engine data Sales designation 1.3 CDTI 1.7 CDTI 1.7 CDTI 1.7 CDTI Engine code Z 13 DTJ Z 17 DT Z 17 DTH Z 17 DTR Number of cylinders 4 4 4 4 Piston displacement [cm3] 1248 1686 1686 1686 Brake horse power [kW/bhp] 55 74 74 92 at rpm 4000 4000 4400 4000 Torque [Nm] 170 260 240 280 at rpm 1750 to 2500 2000 2300 2300 Fuel type1) Diesel Diesel Diesel Diesel Cetane requirement [CN]2) 49 (D)3) 49 (D)3) 49 (D)3) 49 (D)3) Max. permissible engine speed, continuous operation (rpm) approx. 5100 to 5300 4730 4730 4730 Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6

1) Standard quality fuels, e.g. diesel DIN EN 590. 2) Standard quality fuels: D = diesel, bold type: recommended fuel 3) A lower value is possible with winter diesel fuels. 222 Technical Data

Performance Z 14 XEP Z 16 XEP Z 18 XE Z 16 LET Top speed1) [km/h] 5-speed transmission 168 181 190 – 5-gear sport transmission – – – – 6-speed transmission – – – 222 manual transmission automated – 181 190 –

1) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle. Technical Data 223

Performance Z 13 DTJ Z 17 DT Z 17 DTH Z 17 DTR Top speed1) [km/h] 5-speed manual transmission 157 – 178 – 6-speed manual transmission – 180 – 195 manual transmission automated – – – –

1) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle. 224 Technical Data

Fuel consumption, CO2 -emissions The directive is oriented to actual driving The figures given must not be taken as a Directive 80/1268/EEC (last changed practices: Urban driving is rated at approx. guarantee for the actual fuel consumption 1 2 of a particular vehicle. by 2004/3/EC) has applied for the /3 and off-road driving with approx. /3 measurement of fuel consumption (urban and extra-urban consumption). All values are based on the EU base model since 1996. Cold starts and acceleration phases are with standard equipment. also taken into consideration. The calculation of fuel consumption as The specification of CO2 emission is also a specified by directive 2004/3/EC takes constituent of the directive. account of the vehicle’s kerb weight, ascertained in accordance with the said regulation. Optional extras may result in slightly higher fuel consumption and CO2 emission levels than those quoted. Fuel economy, Protecting the environment 3 137. Technical Data 225

Fuel consumption, CO2 emissions Z 14 XEP Z 16 XEP Z 18 XE Z 16 LET 5-speed / sport / 6-gear / manual transmission automated fuel consumption urban [l/100 km] 8.1/–/–/– 8.9/–/–/ 8.9 10.3/–/–/10.1 –/–/ 10.4/– extra-urban [l/100 km] 5.1/–/–/– 5.4/–/–/ 5.4 5.6/–/–/ 5.7 –/–/ 6.3/– combined [l/100 km] 6.2/–/–/– 6.7/–/–/ 6.7 7.3/–/–/ 7.3 –/–/ 7.8/– CO2 [g/km] 148/–/–/– 159/–/–/159 174/–/–/ 174 –/–/ 187/–

Z 13 DTJ Z 17 DT Z 17 DTH Z 17 DTR 5-speed / 6-speed / sport / manual transmission automated fuel consumption urban [l/100 km] 6.2/–/–/– –/ 6.8/–/– 6.6/–/–/– –/ 6.8/–/– extra-urban [l/100 km] 4.3/–/–/– –/ 4.6/–/– 4.4/–/–/– –/ 4.6/–/– combined [l/100 km] 5.0/–/–/– –/ 5.4/–/– 5.2/–/–/– –/ 5.4/–/– CO2 [g/km] 135/–/–/– –/ 146/–/– 139/–/–/– –/ 146/–/– 226 Technical Data

Weights, payload and roof load The combined total of front and rear axle Roof load The payload is the difference between the loads must not exceed the permissible The permissible roof load is 100 kg. The permitted gross vehicle weight (see gross vehicle weight. For example, if the roof load consists of the weight of the roof identification plate 3 218) and the EC kerb front axle is bearing its maximum rack plus the load carried. weight. permissible load, the rear axle can only Driving hints 3 135. Roof rack 3 158. bear a load that is equal to the gross To calculate the kerb weight, enter the vehicle weight minus the front axle load. data for your vehicle below: When the trailer is coupled and the towing z Unladen weight from vehicle fully loaded (including all table 1 3 227 +...... kg occupants), the permissible rear axle load z Weight of heavy (see identification plate or vehicle accessories from documents) may be exceeded by 25 kg table 2 3 227. +...... kg and the permissible gross vehicle weight by Total =...... kg 25 kg. If the permissible rear axle load is exceeded, a maximum speed of 100 km/h is the EC kerb weight. applies. If national regulations specify a Optional equipment and accessories lower maximum speed for vehicles towing increase the kerb weight, which means that a trailer, this must be observed. the payload will also change slightly. See the identification plate or vehicle Note weight ranges in the vehicle documents for permissible axle loads. documents and on the rating plate. Technical Data 227

Table 1, kerb weight1) Meriva Engine Manual Manual transmission transmission automated without/with air Z 14 XEP 1330/1355 –/– conditioning [kg] Z 16 XEP 1375/1400 1375/1400 Z 18 XE 1380/1405 1380/1405 Z 16 LET 1450/1475 –/– Z 13 DTJ 1415/1440 –/– Z 17 DT, Z 17 DTR 1460/1485 –/– Z 17 DTH 1455/1480 –/–

Table 2, weight of heavy accessories Accessories Towing equipment Weight [kg] 25

1) According to EC Directive 70/156/EC, including assumed weights for driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). 228 Technical Data

Tyres If winter tyres are in use, the spare wheel Spare wheel 3 Restrictions may still be fitted with a summer tyre. Use Depending on model, the spare wheel is Not all tyres available on the market of the spare wheel may alter vehicle designed as a temporary spare wheel 3. currently meet the structural requirements. handling. Obtain a replacement for the When using the spare wheel, the driving We recommend that you consult an Opel faulty tyre as soon as possible, and have behaviour may be modified. Replace the Partner concerning suitable tyre makes. the wheel balanced and fitted to the faulty tyre as soon as possible, balance the vehicle. These tyres have undergone special tests wheel and refit to vehicle. Follow the notes 3 3 to establish their reliability, safety and Further information 3 157. on this page and 157, 173. specific suitability for Opel vehicles. On vehicles with alloy wheels 3 the spare Despite continuous market monitoring, we Tyre chains 3 wheel may have a steel rim. Tyre chains may be used on the front are unable to assess these attributes for The spare wheel can be fitted with a wheels only. other tyres, even if they have been granted smaller tyre1) and a smaller rim than the approval by the relevant authorities or in We recommend the use of tyre chains with wheels fitted on the vehicle. some other form. a fine mesh that add no more than 10 mm Further information 3 153. to the running surface and the insides of Tyre pressure (overpressure) the tyres (including chain lock). The specified tyre pressures are valid for Winter tyres 3 Tyre chains are not permitted on tyre cold tyres. The increased tyre pressure Tyres of size 205/50 R 16 are not suitable sizes 205/50 R 16 and 205/45 R 17. resulting from extensive driving must not for use as winter tyres except on vehicles be reduced. The tyre pressures specified on Further information 3 157. with the Z 16 LET engine. the following pages apply to both summer Tyres of size 205/45 R 17 are not suitable Wheels and winter tyres. for use as winter tyres. Wheel bolt tightening torque: 110 Nm. The spare wheel must always be inflated to the tyre pressure for a full load – see table on following pages. Further information 3 153 to 3 157.

1) Country-specific version: The spare wheel is only to be used as a temporary spare wheel. Technical Data 229

Tyre pressure (overpressure)

Suspension behavior when loaded with up With full load to 3 people Tyres – front [kPa/bar] rear [kPa/bar] front [kPa/bar] rear [kPa/bar] Z 14 XEP 175/70 R 14, 240/2.4 220/2.2 260/2.6 300/3.0 185/60 R 15, 205/50 R 16, 205/45 R 17 Z 16 XEP, 185/60 R 15, 240/2.4 220/2.2 260/2.6 300/3.0 Z 18 XE 205/50 R 16, 205/45 R 17 Z 16 LET 185/55 R 161), 280/2.8 260/2.6 300/3.0 340/3.4 195/50 R 161), 205/50 R 16, 205/45 R 17 Z 13 DTJ 185/60 R 15, 240/2.4 220/2.2 260/2.6 300/3.0 205/50 R 16, 205/45 R 17 Z 17 DT, Z 17 DTR 185/60 R 15, 280/2.8 260/2.6 300/3.0 340/3.4 205/50 R 16, 205/45 R 17 Z 17 DTH 185/60 R 15, 260/2.6 240/2.4 280/2.8 320/3.2 205/50 R 16, 205/45 R 17

1) Only permitted as winter tyres. 230 Technical Data

Capacities Engine oil Engine Z 14 XEP Z 16 XEP, Z 18 XE Z 13 DTJ Z 17 DT, Z 17 DTH Z 16 LET Z 17 DTR

Including filter [I] 3.5 4.5 4.25 3.2 5.4 5.0 Between MIN and MAX [I] 1.0 1.0 1.0 1.0 1.0 1.0

Fuel tank Petrol/diesel, nominal 53 53 53 53 53 53 capacity [l] Technical Data 231

Dimensions Meriva Meriva OPC Length [mm] 4052 4068 Width without exterior mirrors [mm] 1694 1694 Width with two exterior mirrors [mm] 1948 1948 Height [mm] 1624 1624 Length of luggage compartment 861 861 floor [mm] Luggage compartment width [mm] 1034 1034 Height of luggage compartment 832 832 opening [mm] [mm] 2630 2630 Turning circle diameter [m] 10.42 10.42 232 Technical Data

Mounting dimensions of towing Dimensions Dimensions 3 equipment [mm] [mm] All measurements refer to Opel-approved towing equipment. A 468 O 425

9 Warning B 727 P 378 Only use towing equipment approved C 508.1 Q 14 for your vehicle. We recommend entrusting retrofitting of towing D 471.5 R 16 equipment to your workshop. E 441.4 S 69

F 497.6 T 76

G 496.6 U 430

H 35.1

I 50.1

J 36.4

K 90

L 142.6

M 585

N 568 Technical Data 233 234 Index

A Automatic anti-dazzle interior mirror..... 39 Index AUX input ...... 112 ABS (Anti-lock Brake System)...... 152 Auxiliary heater...... 127 Accessories...... 171 Accessory socket ...... 78 B Adaptive brake lamp...... 152 Battery ...... 136, 216 Adaptive Forward Lighting ...... 106 Interruption of power supply...... 41, 134 Bulb replacement ...... 188 Battery discharge protection ...... 110 Driving abroad...... 110 Before starting off ...... 15 Adaptive Forward Lighting (AFL)...... 106 Belt tensioners ...... 60 Bulb replacement ...... 188 Bleeding, diesel fuel system ...... 165 Driving abroad...... 110 Bonnet...... 165 Air conditioning system ...... 114 Boot, see Luggage compartment..... 32, 53 Air intake...... 127 Brake assist...... 153 Air recirculation system...... 119, 126 Brake fluid...... 208 Air vents ...... 115 Brake lamp ...... 152 Airbags...... 67 Brake system ...... 151 Alarm...... 36 Brakes Alarm system ...... 34 ABS ...... 152 Alternator...... 85 Brake assist ...... 153 Antenna ...... 111, 196 Brake fluid...... 214 Anti-corrosion service...... 208 Brake lamps...... 191 Antifreeze...... 208, 212 Brake servo unit...... 135 Antifreeze protection ...... 212, 216 Hand brake...... 153 Anti-knock quality of fuel Bulb replacement...... 185 Octane number...... 220 Bulbs...... 184 Anti-theft alarm system...... 34 Anti-theft lock C Alloy wheels ...... 175 Capacities ...... 230 Anti-theft locking system...... 31 Car Pass ...... 26 Towing equipment ...... 160 Caravan/trailer towing...... 135 Aquaplaning...... 156 Care...... 196 Armrest...... 48 Catalytic converter...... 145, 166 Ashtray...... 79 Central locking system...... 28, 30 Index 235

Centre console lighting ...... 108, 109 Coupling socket load ...... 163 E Changing the remote control battery.....29 Courtesy lamp ...... 108 Easytronic ...... 15, 129 Changing wheels ...... 174 Bulb replacement ...... 194 Driving programmes ...... 131 Chassis number, see Vehicle Cruise control...... 148 Fault ...... 133 identification number...... 219 Curtain airbags...... 71 Interruption of power supply...... 134 Child restraint system...... 65 Curve lighting ...... 106 Kickdown...... 132 Child safety locks...... 36, 40 Selector lever...... 15, 130 Cigarette lighter...... 78 D Winter programme...... 132 Climate control system...... 122 Dashboard, see Instrument panel ...... 15 Economical driving...... 137 Clutch operation...... 134, 136 Data...... 26, 218 Electric power steering...... 86 CO2 emissions...... 224 Date...... 92 Electric windows ...... 40 Coin holder...... 81 Daytime running lights...... 102 Electrical system...... 181, 216 Cold start...... 136 Decommissioning ...... 217 Electronic components...... 216 Colour information display ...... 92 Demisting and defrosting Electronic immobiliser ...... 27 Contrast...... 96 Windows...... 118 Electronic Stability Program ...... 146 Control indicator with climate control system ...... 124 Engine code ...... 220, 221 ABS (Anti-lock Brake System) ...... 152 With the air conditioning system...... 121 Engine control indicator ...... 143 Airbag...... 72 Diesel fuel filter ...... 212 Engine oil ...... 207, 210 Engine electronics...... 143 Diesel fuel system...... 165, 212 Additives ...... 207 Exhaust ...... 143 Diesel particle filter...... 41, 86, 136, 144 Top up...... 207 Immobiliser ...... 27 Dimensions...... 231 Viscosity ...... 207 Control indicators ...... 10, 82 Dipped beam...... 11 Engine oil consumption... 135, 210, 220, 221 Adaptive Forward Lighting Bulb replacement ...... 186, 188 Engine oil level...... 210 (AFL) ...... 82, 106 Display...... 90 Engine oil pressure ...... 84 Belt tensioners...... 61 Display mode...... 96 Engine speed ...... 136 Cruise control ...... 148 Door locks ...... 26, 198 Engine wash...... 198 EPS (Electric Power Steering) ...... 86 Driving abroad ...... 199 Environmental protection...... 196 ESP (Electronic Stability Program).....146 Headlamps...... 110 EPS...... 86 Coolant...... 208, 212 Toll systems...... 112 ESP (Electronic Stability Program) ...... 146 Coolant level ...... 213 Driving hints...... 135 Exhaust control indicator ...... 143 Coolant temperature display ...... 88 Exhaust gases...... 144 Coolant thermometer...... 88 Exhaust system...... 135 Cornering light ...... 106 Correcting time ...... 95 236 Index

Exterior lighting switch-off delay...... 107 Glove compartment lighting ...... 109 Height adjustment Exterior mirrors...... 4, 36, 38, 41 Bulb replacement ...... 195 Seat belts ...... 63 Graphical information display ...... 90 Steering wheel ...... 5 F Gross vehicle weight...... 226 High-pressure cleaners ...... 198 Fan...... 114 Gross vehicle weight rating ...... 226 Hill Start Assist...... 153 Fault...... 41 Horn...... 12 Filling station H Engine oil level ...... 210 Halogen headlamp system ...... 185 I Fuel ...... 220, 221 Bulb replacement ...... 185 Identification plate...... 218, 219 Opening the bonnet ...... 165 Driving abroad...... 110 Idling ...... 134 Tyre pressure...... 138, 228 Hand brake...... 16, 153 Ignition switch...... 16, 27 Vehicle data ...... 218, 219 Hazard warning lamps ...... 12, 104 Ignition system ...... 209, 216 Windscreen washer system...... 215 Head restraints...... 21, 46, 47 Immobiliser ...... 27 First-aid kit ...... 171 Headlamp flash...... 11 Information display...... 90 Flat tyre ...... 178 Headlamp range adjustment...... 104 Infotainment system ...... 111 FlexSpace ...... 52 Headlamp switch ...... 11, 102 Instrument display ...... 87 Fog lamps ...... 103 Headlamp washer system13, 100, 101, 215 Instrument illumination...... 108 Bulb replacement...... 191 Headlamps ...... 11 Bulb replacement ...... 196 Fog tail lamp...... 104 Daytime running lights...... 102 Instrument panel ...... 15 Bulb replacement...... 191 Driving abroad...... 110 Instruments ...... 15, 82, 87 Foot brake...... 151, 153 Fog lamps ...... 103 Interior mirror...... 4, 38, 39 Front passenger airbag ...... 67 Reversing lamps...... 104 Interruption of power supply...... 99 Fuel ...... 139, 220, 221 Warning device...... 100 Easytronic...... 134 Fuel consumption ...... 137, 224 Headlights Electric sun roof ...... 43 Fuel filter...... 212 Changing bulbs ...... 185 Electric windows ...... 41 Fuel gauge ...... 88 Heated exterior mirrors...... 13, 38, 41 Electronic Stability Program ...... 147 Fuel system, diesel...... 165 Heated rear window ...... 13, 38, 41 ISOFIX ...... 79 Fuses...... 181 Heated seats...... 46 Heating ...... 114, 117 J G Seats ...... 46 Jack ...... 171, 176 Gears ...... 14, 134 With climate control system ...... 123 Jump leads...... 166 Generator, see Alternator ...... 85 With the air conditioning system...... 114 Glasses compartment ...... 81 Glove compartment ...... 80 Index 237

K M Oil consumption ...... 210, 220, 221 Oil level...... 210 Key Main beam...... 11 Oil pressure...... 84 extending ...... 26 Bulb replacement ...... 187, 188 Opel Service...... 199 ignition lock...... 16, 27 Control indicator...... 84 Operating temperature ...... 136 Locking doors...... 28, 30, 36 Maintenance Outside temperature gauge ...... 91 Starting ...... 27 Air conditioning system...... 128 Overrun ...... 136, 138 Starting the engine ...... 16 Antifreeze protection ...... 212 Keys ...... 26 Brake fluid ...... 214 P L Brakes...... 213 Paintwork damage...... 197 Catalytic converter ...... 145 Park pilot...... 150 Language selection...... 95 Engine oil...... 210 Parking lamps...... 11 Lashing eyes ...... 57 Fuel consumption ...... 138 Bulb replacement ...... 189 Leather trim ...... 197 Tyre pressure...... 154, 228 Pedals...... 136 Light switch ...... 11 Tyres ...... 155 Performance ...... 222 Lighting ...... 11, 102 Manual transmission...... 14, 134 Pollen filter ...... 127 Driving abroad...... 110 Mirrors ...... 4, 38 Power assisted steering, Loading ...... 58, 162, 226 Misted windows ...... 118, 121, 124 see electronic power steering...... 86 Loading the vehicle ...... 58 Mobile telephone...... 113 Power steering, see electronic Locking doors ...... 2, 28, 30, 36 Muffler, see Exhaust system ...... 144 power steering...... 86 Locking from the inside...... 30 Preheating ...... 86 Lubricants ...... 210 N Pushing, towing...... 142, 166 Luggage compartment Number plate lamps Bulb replacement...... 195 Bulb replacement ...... 193 Q Cover...... 55 Number plate lighting...... 193 Quickheat ...... 127 Extension ...... 32, 53 Number plates...... 217 Lighting ...... 109 R O Loading ...... 58, 162, 226 Radio ...... 24, 111 Luggage compartment cover ...... 55 Octane numbers...... 220, 221 Radio equipment (CB) ...... 113 Lumbar support...... 45 Odometer...... 87 Radio reception...... 111 Oil ...... 207 Radio remote control ...... 28 Additives ...... 207 Reading lamps ...... 109 Top up ...... 207 Rear lamp cluster ...... 102 Viscosity...... 207 Bulb replacement ...... 191 238 Index

Rear seats...... 51 Self-help Tail lamps ...... 102 Rear window washer system ...13, 101, 215 Central locking...... 31 Bulb replacement ...... 191 Refuelling...... 140 Electric windows...... 40 Tank Fuel filler cap...... 141 Information display ...... 92 Fuel gauge...... 88 Remote control Radio remote control ...... 29 Technical data ...... 218 Central locking system ...... 28 Self-help, care for your car ...... 165 Telephone, see Mobile telephone...... 113 Steering wheel...... 24, 111 Service interval display ...... 208 Temperature regulation ...... 123 Replacement keys ...... 26 Service intervals...... 199 Tempomat, see cruise control...... 148 Reversing lamps...... 107 additional work...... 206 Temporary spare wheel...... 158, 173 Bulb replacement...... 191 hard driving conditions ...... 206 The first 1000 km...... 135 Roof load...... 58, 135, 138, 226 main inspection ...... 199 Tightening torque ...... 177, 228 Roof rack ...... 58, 138, 158 Service work ...... 208 Time...... 92 Roof racks ...... 58, 138 Side airbags...... 69 Toll systems ...... 112 Running-in...... 135 Signal system...... 11, 12 Tools...... 171 Brakes ...... 213 Spare wheel ...... 172, 174 Towing equipment ...... 158 Speed...... 137, 138 Towing eye ...... 168, 170 S Fuel consumption ...... 137, 138 Transmission...... 14 Safeguard against Speedometer ...... 87 Manual transmission...... 134 unauthorised use ...... 15, 17, 27, 36 Starting the engine...... 15, 27, 130, 166 Transmission, Easytronic ...... 129 Safety accessories ...... 171 Self-help...... 166 Driving programmes ...... 131 Safety net ...... 56 Steam-jet cleaners...... 198 fault ...... 133 Safety systems ...... 111 Steering column lock...... 15 Interruption of power supply...... 134 Saving energy ...... 136 Steering wheel adjustment ...... 5 Kickdown...... 132 Seat adjustment ...... 2, 44, 51 Steering wheel remote control ...... 24, 111 Selector lever...... 15, 130 Seat belts...... 62, 198 Stowage compartments ...... 80 Winter programme...... 132 Seat height adjustment...... 3, 45 Sun roof...... 42 Travel Assistant...... 22, 48, 49 Seat occupancy recognition...... 72 Fault...... 43 Tread depth...... 155 Seat position ...... 2, 44, 45 Sun shade ...... 43 Trip computer...... 23, 97 Seats ...... 2, 44 Sun visors ...... 81 Trip odometer...... 87 Extending the luggage System settings...... 94 Triple information display ...... 90 compartment ...... 32, 53 Turn signal lamps...... 11, 103 heated ...... 46 T Turn signals Selector lever...... 130 Tables...... 81 Bulb replacement ...... 190, 191 Self-diagnosis...... 61, 72, 153 Tachometer...... 87 Twin Audio...... 24, 112 Index 239

Tyre chains...... 157, 228 Winter mode Tyre condition...... 155 Starting-off aid ...... 132 Tyre pressure...... 154, 228 Winter operation Tyre repair kit...... 178 Battery...... 136 Coolant, antifreeze...... 212 U Fuel consumption ...... 138 Units of measure...... 96 Fuel for diesel engines...... 139 Unleaded fuel ...... 142, 220, 221 Heating...... 114 Locks...... 198 V Tyre chains...... 157, 228 Valve cap key ...... 154 Window demisting and Vehicle care...... 196 defrosting ...... 118, 121, 124 Vehicle decommissioning...... 217 Windscreen washer system, Vehicle identification number...... 219 antifreeze protection...... 216 Vehicle keys, see Keys...... 26 Winter programme...... 132 Vehicle recommissioning...... 217 Winter tyres...... 228 Ventilation...... 114, 117, 125 X W Xenon headlamp system Warning buzzers...... 100 Bulb replacement ...... 188 Warning triangle...... 171 Driving abroad...... 110 Washer fluid reservoir, windscreen washer system ...... 215 Weights...... 226 Wheels ...... 153 Wheels, tyres...... 153 Windows...... 39 Demisting and defrosting . 118, 121, 124 Windscreen washer system...... 13, 100, 101, 215 Antifreeze protection...... 216 Washer fluid reservoir...... 215 Windscreen wipers...... 12, 100, 215 240 Index

Copyright by ADAM OPEL GmbH, Rüsselsheim, Germany. The information contained in this publication is valid as of the date indicated below. Adam Opel GmbH reserves the right to make changes to the technical specifications, features and design of the vehicles relative to the information contained in this publication, as well as changes to the publication itself. Edition: August 2009, ADAM OPEL GmbH, Rüsselsheim. Printed on chlorine-free bleached paper. KTA-2540/10-en 13 127 076 Art.-Nr. 09 927 4210 08/2009