DOCSLIB.ORG

DIY Shiplap Building Guide

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
DIY Shiplap Building Guide DIY SHIPLAP HEADBOARD BUILDING PLANS: Description: Complete Building Guide for a king size shiplap headboard Tools Needed: Jig Saw Skill saw Finish Nailer Measuring Tape Marking Pencil 1/16 tile spacers Twine and nail Materials: (9) 1"x6"x8' Pine Board (1) 4'x8' 1/4 Piece of Plywood Liquid Nails or Construction Adhesive 1.5" Finish Nails 1" Wood Screws Directions: 1. Cut the plywood to size. You want your plywood to be 48" x 80". The 4 foot side will be fine but you will have to cut the 8' side down to 80". Measure over to 80", mark with your pencil, and cut using your skill saw. 2. Now you need to cut the arched area on the piece of plywood. To get a precise arch you can use the nail and twine method. See more at: www.plumprettydecoranddesign.com Page "1 of "4 Here's how: A. First measure over 40" and mark. B. From that mark measure down 20" and place your nail. C. Using a piece of twine and your pencil, attach the twine to the nail and your pencil with a 20" gap between the two. D. Now stretch out the twine and mark your circle. Creating a circle with a 40" diameter. E. Next create a pivot point with a board. Meaning use a stationary point that can not move (a clamped board) and place your nail in. This time using a piece of twin and your pencil, attach the twine to the nail and your pencil with a 40" gap between the two. Creating a 80” diameter circle. F. Stretch the twine out, line it up with the edge of the center circle and mark your circle. Do this on both sides creating two arches on each side of the center circle. See more at: www.plumprettydecoranddesign.com Page "2 of "4 3. Now that you have your arch area drawn out cut along the the lines with the Jig Saw. 4. Next Step is attaching your 1"x6"x8' Pine Boards to the plywood. Start at the bottom and work your way all the way to the top with 9 boards. Between each board us a 1/16 tile spacer for even spacing. Apply Liquid Nail or construction adhesive to the back of each board and tack it up the the fish nailer to keep them in place. Once you get all the boards nailed on, turn it over and use wood screws the properly secure the boards to the piece of plywood. See more at: www.plumprettydecoranddesign.com Page "3 of "4 5. Turn the headboard over with the plywood facing up. Using the Jig saw cut the boards at the top following along the arched template of the plywood. Use the edge of the plywood as your guide. 6. Sand the edges of the boards for a smooth finish then paint your desired color. I recommend Alabaster White by Sherwin Williams for a white farmhouse look. 7. You can either attach hangers for hanging on the wall (you will need to anchor into the wall due to the weight), or you can attach legs to the bottom so it will have support from the floor. I recommend using a 2"x6" for this. Just attach to the back of the plywood a few inches in on each side. The height of the boards will depend on your bed frame, box spring and mattress. You want the bottom of the headboard to rest and few inches below the top of your mattress. Paint the legs with the same color as the headboard *Remember to paint the sides- so you don't have any wood showing. See more at: www.plumprettydecoranddesign.com Page "4 of "4.
Load more

Recommended publications
  • Historic Context Statement City of Benicia February 2011 Benicia, CA
    Historic Context Statement City of Benicia February 2011 Benicia, CA Prepared for City of Benicia Department of Public Works & Community Development Prepared by page & turnbull, inc. 1000 Sansome Street, Ste. 200, San Francisco CA 94111 415.362.5154 / www.page-turnbull.com Benicia Historic Context Statement FOREWORD “Benicia is a very pretty place; the situation is well chosen, the land gradually sloping back from the water, with ample space for the spread of the town. The anchorage is excellent, vessels of the largest size being able to tie so near shore as to land goods without lightering. The back country, including the Napa and Sonoma Valleys, is one of the finest agriculture districts in California. Notwithstanding these advantages, Benicia must always remain inferior in commercial advantages, both to San Francisco and Sacramento City.”1 So wrote Bayard Taylor in 1850, less than three years after Benicia’s founding, and another three years before the city would—at least briefly—serve as the capital of California. In the century that followed, Taylor’s assessment was echoed by many authors—that although Benicia had all the ingredients for a great metropolis, it was destined to remain in the shadow of others. Yet these assessments only tell a half truth. While Benicia never became the great commercial center envisioned by its founders, its role in Northern California history is nevertheless one that far outstrips the scale of its geography or the number of its citizens. Benicia gave rise to the first large industrial works in California, hosted the largest train ferries ever constructed, and housed the West Coast’s primary ordnance facility for over 100 years.
    [Show full text]
  • Creating a Wood Accent Wall Recommended Products
    Creating A Wood Accent Wall Recommended Products When Tonnie eradiating his Primavera payings not unresponsively enough, is Giovanne hydropathical? Transmarine Brett unhelm some toolrooms after irremediable Ruddie twists suavely. Ordinate Constantine scythes: he singularized his intake sportively and toploftily. The accent color creates a fireplace on this manhattan guest room creating the slip covers. Although Elmer's Glue are the weakest glue hold the sanded results Super Glue under the weakest Glue onto the non-sanded results and Tacky Glue being the strongest glue overall. For a metal applications and cleat will do this at benjamin moore white to add a tighter budget friendly decor styling tips, creating a wood accent wall. Add wood accent wall a room they so be. How to plum a Decorative Wood Wall being Less than 200 YouTube. How you Save Money was Doing to Yourself! A axe of Glues California Science & Engineering Fair. The UFP-Edge Rustic Collection is holding for lease next reclaimed wood project. Buy Real Weathered Wood Planks for walls Rustic Reclaimed barn wood paneling. Does wild can make life feel claustrophobic at the mere mention make it. My dear is Erin and I with a DIY nut. This gap then recommend products, create a sound investment with screws used for awesome jacket has a balance in any home to choose a complimentary consultation. My accent wall product, products purchased through and. Instead form a shiplap accent wall table will allow your wood this stand erect without. Get coordinating colors then preview them in you room image. And create your home products that rustic look that skinny section off center of woods they stand alone.
    [Show full text]
  • A-Lign Technical Manual – Vertical Shiplap Weatherboard
    A-lign Technical Manual – Vertical Shiplap Weatherboard High Moisture Protection System Solution Fast Install & Less Waste From Renewable Wood Appraisal No. 929 []2017 Primed & Undercoated BRANZ Appraised From Renewable Wood NZBC Compliant claymark.co.nz A-lign® by Claymark aligns natural sustainable timber to modern design needs – combining striking good looks with guaranteed high performance. Renewable natural pine The NZ radiata pine used in the A-lign Vertical Once finger-jointed they form products Shiplap timber cladding system solution is that exceed the pine’s original physical and from renewable and sustainable plantation structural characteristics by over 400%. resources. This makes it a brilliant natural ‘environmentally It is a remarkably versatile timber renowned friendly’ construction choice over alternative for exceptional machining properties, durability building materials made from non-renewable and lightness. fossil fuels. Branz Impact Test Independently assessed Impact resistance is a key criteria for cladding A BRANZ Appraisal is a comprehensive materials being used in the construction of independent assessment of building products Appraisal No. 929 []2017 schools and similar light commercial buildings and systems for fitness for purpose and not exceeding 10 metres in height. To meet Building Code compliance. regulatory and specifier requirements, A-lign The A-lign Vertical Shiplap timber cladding Vertical Shiplap timber weatherboard (18mm system solution has been vigorously assessed thick) were subjected to hard body high from manufacturing processes, through impact resistance tests performed by BRANZ. to fitness for purpose, durability, weather- High density fibre cement weatherboard tightness performance and structural capability (16mm thick) were also included in over a drained and vented cavity.
    [Show full text]
  • ARAUCO Nickel Gap Shiplap Installation Instructions
    Installation Instructions MOULDING SHIPLAP MARCH 2018 GUIDE Getting Started ARAUCO Primed Shiplap is attractive and Each project site and home is a little different. These instructions focus mainly on feature wall applications, but they also apply to other versatile. It can be installed in many patterns situations like using shiplap as wainscoting for example. over different substrates and it can be Here are some things to consider before beginning your project. configured in a variety of ways---feature • The transition between existing moldings and the shiplap walls, wainscoting, bathtub surround and • The transition between existing w alls and shiplap • When installing over existing drywall, moving device boxes out to more. It can be installed from the bottom up be flush with the new wall surface • “Sliver cuts”. If there is going to be a piece cut lengthwise to fit or the top down. Because it is solid wood, (“ripped”) would that look best at the top or bottom of the wall? it can be tailored to fit the site conditions • Are the top and bottom of the wall parallel with each other? • Tool safety. Make sure you read and understand the instructions of your home or project with common that come with your tools. Practice with them if you’re new to woodworking tools. home improvement projects. • It is an interior product, not to be used in outside applications. Watch our installation videos! Coverage: Each 8-foot (96-inches) long 5-1/4” wide piece of ARAUCO Primed Shiplap covers approximately 3-square feet. For a single wall, multiply the height by the width to get the total square footage of the www.arauco-na.com area to be covered.
    [Show full text]
  • True Shiplap Vinyl Hardwood Wall Planks Faq's Q
    TRUE SHIPLAP VINYL HARDWOOD WALL PLANKS FAQ’S Q: What makes From The Forest Wall Planks innovative/ better than our competitors? A: 1. Engineered with an HDF core for durability so your wall will last a lifetime! 2. Engineered with "Wall Flex," an HDF core and completed with a front and back face veneer that is finished with WearMax - making the planks both DURABLE & FLEXIBLE 3. Environmentally Friendly 4. Engineered with a SHIPLAP EDGE to achieve the desired “nickel gap” aesthetic and to ensure that even if the seasons change the planks will not move! 5. Proudly MADE IN THE USA - Central Wisconsin by From The Forest Q: What is HDF? A: Also referred to as hardboard, a high-density fiberboard (HDF) is a type of engineered wood product. It's made from wood fiber extracted from chips and pulped wood waste. HDF is similar but much harder and denser than particle board or medium density fiberboard (MDF). Q: What is veneer? A: Wall Plank veneer is a thin decorative covering of fine wood applied to the front face and the back face of our environmentally friendly HDF core. Q: What is the average length of Wall planks? A: Wallplanks come in lengths anywhere between 46"-47" with over 80% of the boards in a carton being the full 47" length. Q: What is the radius the boards can flex? A: Wall Plank boards have a built-in feature called "Wall Flex" that helps each board to contour to slightly out of flat walls. The product is not designed to flex around or over architecturally contoured or curved walls.
    [Show full text]
  • Standard Patterns Western Wood Products Association STANDARD PATTERNS
    WP-7 8" LOG CABIN SIDING - - - - - - 2 SHIPLAP Western Wood Products Association Standard Patterns Western Wood Products Association STANDARD PATTERNS CONTENTS STANDARD PATTERNS N1E Nosed one edge LUMBER ABBREVIATIONS N2E Nosed two edges Paneling . 4 OS One side Paneling and Siding . 6 BEV Beveled PAT Pattern Siding . 7 BEV SDG Beveled siding P1E Planed one edge BS Both sides P2E Planed two edges Ceiling . 12 CB Center Beaded P1S Planed one side Ceiling and Partition . 13 CB1S Center bead one side P2S Planed two sides Partition . 14 CB2S Center bead two sides P4S Planed four sides CG Center groove P1S1E Planed one side one edge Shiplap . 15 CG2E Center groove two edges P2S1E Planed two sides one edge Tongued & Grooved . 16 CLG Ceiling P1S2E Planed one side two edges Decking . 16 CM Center matched PAR Planed all 'round CS Caulking seam PART Partition Decking and Flooring . 20 CSG Casing PE Planed edge Flooring . 21 CV Center Vee PPE Planed plain edge Corn Cribbing . 22 CV1S Center vee one side PSE Planed square edge CV2S Center vee two sides PSJ Planed and square jointed Grooved Roofing . 22 D2S Dressed two sides PTG Planed tongued and grooved Patent Lath . 22 D4S Dressed four sides R&B Rabbet & bead Stile . 22 DB CLG Double-beaded ceiling S Side, Surfaced DB PART Double-beaded partition SB1S Single bead one side Sill . 22 DBL T&G Double tongued & grooved SDG Siding Jamb . 22 D&CM Dressed & center matched SG Slash (flat) grain Ogee Batten . 23 DKG Decking S/L, or SL Shiplap D/S,DS Drop Siding SQ Square Casket Stock .
    [Show full text]
  • Chapter 5--Commercial Lumber
    Chapter 5 Commercial Lumber Kent A. McDonald and David E. Kretschmann n a broad sense, commercial lumber is any lumber Contents that is bought or sold in the normal channels of Hardwood Lumber 5–1 commerce. Commercial lumber may be found in a variety of forms, species, and types, and in various commer- Factory Lumber 5–2 cial establishments, both wholesale and retail. Most com- Dimension and Component Parts 5–2 mercial lumber is graded by standardized rules that make purchasing more or less uniform throughout the country. Finished Market Products 5–6 When sawn, a log yields lumber of varying quality. To Lumber Species 5–7 enable users to buy the quality that best suits their purposes, Softwood Lumber 5–7 lumber is graded into use categories, each having an appro- priate range in quality. Lumber Grades 5–7 Lumber Manufacture 5–10 Generally, the grade of a piece of lumber is based on the number, character, and location of features that may lower the Softwood Lumber Species 5–12 strength, durability, or utility value of the lumber. Among Softwood Lumber Grading 5–12 the more common visual features are knots, checks, pitch pockets, shake, and stain, some of which are a natural part of Purchase of Lumber 5–12 the tree. Some grades are free or practically free from these features. Other grades, which constitute the great bulk of Retail Yard Inventory 5–16 lumber, contain fairly numerous knots and other features. Important Purchase Considerations 5–17 With proper grading, lumber containing these features is entirely satisfactory for many uses.
    [Show full text]
  • APA Engineered Wood Construction Guide
    Engineered Wood CONSTRUCTION GUIDE Engineered Wood Construction Guide 2 WOOD The Natural Choice Engineered wood products are a good choice for the environment. They are manufactured for years of trouble-free, dependable use. They help reduce waste by decreasing disposal costs and product damage. Wood is a renewable, recyclable, biodegradable resource that is easily manufactured into a variety of viable products. A few facts about wood. ■ We’re growing more wood every day. Forests fully cover one-third of the United States’ and one-half of Canada’s land mass. American landowners plant more than two billion trees every year. In addition, millions of trees seed naturally. The forest products industry, which comprises about 15 percent of forestland ownership, is responsible for 41 percent of replanted forest acreage. That works out to more than one billion trees a year, or about three million trees planted every day. This high rate of replanting accounts for the fact that each year, 27 percent more timber is grown than is harvested. Canada’s replanting record shows a fourfold increase in the number of trees planted between 1975 and 1990. ■ Life Cycle Assessment shows wood is the greenest building product. A 2004 Consortium for Research on Renewable Industrial Materials (CORRIM) study gave scientific validation to the strength of wood as a green building product. In examining building products’ life cycles – from extraction of the raw material to demolition of the building at the end of its long lifespan – CORRIM found that wood was better for the environment than steel or concrete in terms of embodied energy, global warming potential, air emissions, water emissions and solid waste production.
    [Show full text]
  • THE ENGINEERED WOOD ASSOCIATION Be Constructive WOOD Wood Is the Right Choice for a Host of Construction Applications
    ENGINEERED WOOD CONSTRUCTION GUIDE APA THE ENGINEERED WOOD ASSOCIATION Be Constructive WOOD Wood is the right choice for a host of construction applications. It is the earth’s natural, energy efficient and renewable building material. Engineered wood is a better use of wood. It uses less wood to make more wood products. That’s why using APA trademarked I-joists, glued laminated timbers, laminated veneer lumber, plywood and oriented strand board is constructive ... for the environment, for innovative design, and for strong, durable buildings. A few facts about wood. I We’re not running out of trees. One-third of the United States land base – 731 million acres – is covered by forests. About two-thirds of that 731 million acres is suitable for repeated planting and harvesting of timber. But only about half of the land suitable for growing timber is open to logging. Most of that harvestable acreage also is open to other uses, such as camping, hiking, and hunting. Forests fully cover one-half of Canada’s land mass. Of this forestland, nearly half is considered productive, or capable of producing timber on a sustained yield basis. Canada has the highest per capita accumulation of protected natural areas in the world – areas including national and provincial parks. I We’re growing more wood every day. American landowners plant more than two billion trees every year. In addition, millions of trees seed naturally. The forest products industry, which comprises about 15 percent of forestland ownership, is responsible for 41 percent of replanted forest acreage. That works out to more than one billion trees a year, or about three million trees planted every day.
    [Show full text]
  • Vertical Shiplap Stud Frame: Batten Fixing - Timber Sub-Floor NCC & AS1684 As Pictured 2.0 Typical Plastic Horseshoe Packing 1:15 9
    GENERAL NOTES: Moisture Vapour barrier or relevant 1. Do not scale Drawings. If drawings are in question or Noggins at 600mm centres max. impermeable wall underlay as per Noggins to comply with AS1684.2 (6.2.1.5) Moisture Vapour barrier or relevant discrepancy, the builder shall be responsible for obtaining impermeable wall underlay as per NCC and AS1684 Vertical installation is recommended to have fixings at 450mm maximum clarification from the building designer and or building NCC and AS1684 Timber battens at 600mm centres max. Timber or plastic shim spacer as appropriate (Min 10mm) Minimum H2 or Class 3 surveyor before continuing with construction. Vertical installation is recommended to Noggins to comply with AS1684.2 (6.2.1.5). have fixings at 450mm maximum Vertical installation is recommended to have fixings at 600mm 2. All dimensions relating to existing conditions shall be field maximum. 110mm SQE is recommended no more than 450mm verified. Noggins to comply with AS1684.2 (6.2.1.5). fixingTimber battens at 600mm centres max. Minimum H2 or Class 3. End cuts to be mitred and flush joined. Vertical installation is recommended to have fixings at 600mm maximum. End cuts to be mitred and flush joined. Cuts to be sealed with relevant sealer 110mm SQE is recommended no more than 450mm fixingTimber battens Cuts to be sealed with relevant sealer product as appropriate 3. Where otherwise specified all products shall be installed at 600mm centres max. Minimum H2 or Class 3. product as appropriate according to Radial Timbers specifications. This applies not withstanding any relevant Building Act, Regulation, Building Code of Australia, Local Government S03:A1/B1 S03:A1/B1 Regulation/Requirement and Australian Standard.
    [Show full text]
  • Field Observations and Laboratory Tests of Water Migration in Walls with Shiplap Hardboard Siding
    Field Observations and Laboratory Tests of Water Migration in Walls with Shiplap Hardboard Siding George A. Tsongas, Ph.D., P.E. Dennis P. Govan, AlA Jack A. McGillis Member ASHRAE ABSTRACT In a number of legal cases across the country it has been alleged that hardboard siding performs poorly from a moisture point a/view and thus is not a satisfactory siding material. In one particular case involving an apartment complex of ahout 400 units in the San Francisco Bay area, decay of hoth hardboard siding and wood trim as well as other wood members was noted and has been documentedfor this paper. It was clearly found that the decay was primarily caused by substantial amounts of liquid rainwater leaking behind the siding and other wood members. However, other decay or deterioration (e.g., swelling) ofthe siding was noted in areas where liquid water intrusion was not directly observed. We speculated that liquid water might move laterally behind the siding from leak sites in the building envelope, and that might explain the existence of siding swelling observed at locations some distance horizontally from otherwise obvz'ous leak sites. Deterioration o/the hardboard siding also was found to be caused by a number of other installation problems such as allowing the bottom edge of the siding to be in direct contact with concrete. We also noted swelling ofsome bottom courses afthe siding and speculated that standing water on concrete paving might be wicking up the gypsum sheathing behind the siding. It also was alleged that rainwater was wicking up between the siding laps and causing swelling and cracking ofthe siding.
    [Show full text]
  • Chapter 10--Wood-Based Composites and Panel Products
    Chapter 10 Wood-based Composites and Panel Products John A. Youngquist ecause wood properties vary among species, Contents between trees of the same species, and between Scope 10–2 pieces from the same tree, solid wood cannot match reconstituted wood in the range of properties that can be Types of Conventional Composite Materials 10–3 controlled in processing. When processing variables are Adhesive Considerations 10–3 properly selected, the end result can sometimes surpass nature’s best effort. With solid wood, changes in properties Additives 10–4 are studied at the cellular level. With reconstituted wood General Manufacturing Issues 10–4 materials, changes in properties are studied at the fiber, particle, flake, or veneer level. Properties of such materials Standards for Wood–Based Panels 10–4 can be changed by combining, reorganizing, or stratifying Product Standards 10–5 these elements. Performance Standards 10–5 The basic element for composite wood products may be the fiber, as it is in paper, but it can also be larger wood particles Plywood 10–6 composed of many fibers and varying in size and geometry. General Description 10–6 These characteristics, along with control of their variations, provide the chief means by which materials can be fabricated Types of Plywood 10–7 with predetermined properties. Processing Considerations 10–7 In any discussion of the strength properties of wood-based Specifications 10–8 panels and other adhesive-bonded wood composites, the first consideration is the constituents from which these products Grades and Classification 10–9 are made (O’Halloran and Youngquist 1984; Youngquist Specialty Panels 10–13 1987, 1988).
    [Show full text]