Addendum #2 IFB 21-06-406 Page 1

Mobility Solutions & Customer Care Center Addendum #2 IFB 21-06-406 Page 1

ADDENUM #2

This Addendum is being issued prior to the due date for receipt of bids. This Addendum forms a part of the Contract Documents and modifies the original Information issued for bid on July 13, 2021. All other provisions of the Contract Documents shall remain unchanged.

Acknowledged receipt of this Addendum on the Acknowledgement of Addendum Form is required. Failure to do so may result in disqualification of the Bidder.

CHANGES TO THE ADDENDUM #1 NARRATIVE:

1. Sheet S101 was included in Addendum #1 and there were revisions to it.

CHANGES TO THE SPECIFICATIONS

1. Section 08 34 73.16 – Wood Sound Control Door Assemblies a. Replace part 2.1, paragraph A.1. with the following, “STC Rating: 47 as calculat- ed by ASTM E 413 when tested in an operable condition according to ASTM E 90.” 2. Section 08 71 00 – Door Hardware a. Add hardware set 19.0 and 20.0 for doors 32 and 33, respectively. These are the hardware for the security gates. This revised section will be included in this addendum. 3. Section 08 88 53 – Security Glazing a. Add the new specification section attached to this addendum. 4. Section 09 91 13 – Exterior Painting a. Add the new Specification Section attached to this addendum. 5. Section 26 09 23 – Lighting Control Devices a. Replace this specification section in its entirety with the attached as part of this addendum. 6. Section 27 05 00 – Communications a. Replace this specification section in its entirety with the attached as part of this addendum. b. All references to “Purdue College” have been removed. 7. Section 27 05 28 – Pathways for Communications Systems a. Replace this specification section in its entirety with the attached as part of this addendum b. All references to “Purdue College” have been removed. 8. Section 27 11 19 – Termination Blocks and Patch Panels a. Replace this specification section in its entirety with the attached as part of this addendum. b. All references to “Purdue College” have been removed. 9. Section 32 31 00 – Decorative Metal Fences and Gates a. Add the new Specification Section attached to this addendum.

CHANGES TO THE DRAWINGS

1. C401 – Utility Plan: Replace sheet with attached.

ETICA GROUP Project # 200061.04 Mobility Solutions & Customer Care Center Addendum #2 IFB 21-06-406 Page 2

2. E601 – Electrical Schedules: Replace sheet with attached. a. Exterior wall packs, S1 and S1A, are to have photosensors.

ATTACHMENTS: Section 08 71 00 – Door Hardware Section 08 88 53 – Security Glazing Section 09 91 13 – Exterior Painting Section 26 09 23 – Lighting Control Devices Section 27 05 00 – Communications Section 27 05 00 – Pathways for Communications Systems Section 27 11 19 – Termination Blocks and Patch Panels Section 32 31 00 – Decorative Metal Fences and Gates C401 – Utility Plan E601 – Electrical Schedules

END OF ADDENDUM #2

ETICA GROUP Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 1 of 32

SECTION 08 71 00 - DOOR HARDWARE

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes commercial door hardware for the following:

1. Swinging doors. 2. Other doors to the extent indicated.

B. Door hardware includes, but is not necessarily limited to, the following:

1. Mechanical door hardware. 2. Cylinders specified for doors in other sections.

C. Related Sections:

1. Division 08 Section “Hollow Metal Doors and Frames”. 2. Division 08 Section “Flush Wood Doors”.

D. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.

1. ANSI A117.1 - Accessible and Usable Buildings and Facilities. 2. ICC/IBC - International Building Code. 3. NFPA 70 - National Electrical Code. 4. NFPA 80 - Fire Doors and Windows. 5. NFPA 101 - Life Safety Code. 6. NFPA 105 - Installation of Smoke Door Assemblies. 7. UL/ULC and CSA C22.2 - Standards for Automatic Door Operators Used on Fire and Smoke Barrier Doors and Systems of Doors. 8. State Building Codes, Local Amendments.

E. Standards: All hardware specified herein shall comply with the following industry standards as applicable. Any undated reference to a standard shall be interpreted as referring to the latest edition of that standard:

1. ANSI/BHMA Certified Product Standards - A156 Series. 2. UL10C - Positive Pressure Fire Tests of Door Assemblies.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 2 of 32

3. ANSI/UL 294 - Access Control System Units. 4. UL 305 - Panic Hardware. 5. ANSI/UL 437- Key Locks.

1.3 SUBMITTALS

A. Product Data: Manufacturer's product data sheets including installation details, material descriptions, dimensions of individual components and profiles, operational descriptions and finishes.

B. Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of door hardware, as well as procedures and diagrams. Coordinate the final Door Hardware Schedule with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware.

1. Format: Comply with scheduling sequence and vertical format in DHI's "Sequence and Format for the Hardware Schedule."

2. Organization: Organize the Door Hardware Schedule into door hardware sets indicating complete designations of every item required for each door or opening. Organize door hardware sets in same order as in the Door Hardware Sets at the end of Part 3. Submittals that do not follow the same format and order as the Door Hardware Sets will be rejected and subject to resubmission.

3. Content: Include the following information:

a. Type, style, function, size, label, hand, and finish of each door hardware item. b. Manufacturer of each item. c. Fastenings and other pertinent information. d. Location of door hardware set, cross-referenced to Drawings, both on floor plans and in door and frame schedule. e. Explanation of abbreviations, symbols, and codes contained in schedule. f. Mounting locations for door hardware. g. Door and frame sizes and materials. h. Warranty information for each product.

4. Submittal Sequence: Submit the final Door Hardware Schedule at earliest possible date, particularly where approval of the Door Hardware Schedule must precede fabrication of other work that is critical in the Project construction schedule. Include Product Data, Samples, Shop Drawings of other work affected by door hardware, and other information essential to the coordinated review of the Door Hardware Schedule.

C. Shop Drawings: Details of electrified access control hardware indicating the following:

1. Wiring Diagrams: Upon receipt of approved schedules, submit detailed system wiring diagrams for power, signaling, monitoring, communication, and control of

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 3 of 32

the access control system electrified hardware. Differentiate between manufacturer-installed and field-installed wiring. Include the following:

a. Elevation diagram of each unique access controlled opening showing location and interconnection of major system components with respect to their placement in the respective door openings. b. Complete (risers, point-to-point) access control system block wiring diagrams. c. Wiring instructions for each electronic component scheduled herein.

2. Electrical Coordination: Coordinate with related sections the voltages and wiring details required at electrically controlled and operated hardware openings.

D. Keying Schedule: After a keying meeting with the owner has taken place prepare a separate keying schedule detailing final instructions. Submit the keying schedule in electronic format. Include keying system explanation, door numbers, key set symbols, hardware set numbers and special instructions. Owner must approve submitted keying schedule prior to the ordering of permanent cylinders/cores.

E. Informational Submittals:

1. Product Test Reports: Indicating compliance with cycle testing requirements, based on evaluation of comprehensive tests performed by manufacturer and witnessed by a qualified independent testing agency.

F. Operating and Maintenance Manuals: Provide manufacturers operating and maintenance manuals for each item comprising the complete door hardware installation in quantity as required in Division 01, Closeout Procedures.

1.4 QUALITY ASSURANCE

A. Manufacturers Qualifications: Engage qualified manufacturers with a minimum 5 years of documented experience in producing hardware and equipment similar to that indicated for this Project and that have a proven record of successful in-service performance.

B. Certified Products: Where specified, products must maintain a current listing in the Builders Hardware Manufacturers Association (BHMA) Certified Products Directory (CPD).

C. Installer Qualifications: A minimum 3 years documented experience installing both standard and electrified door hardware similar in material, design, and extent to that indicated for this Project and whose work has resulted in construction with a record of successful in-service performance.

D. Door Hardware Supplier Qualifications: Experienced commercial door hardware distributors with a minimum 5 years documented experience supplying both mechanical and electromechanical hardware installations comparable in material, design, and extent to that indicated for this Project. Supplier recognized as a factory

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 4 of 32

direct distributor by the manufacturers of the primary materials with a warehousing facility in Project's vicinity. Supplier to have on staff a certified Architectural Hardware Consultant (AHC) available during the course of the Work to consult with Contractor, Architect, and Owner concerning both standard and electromechanical door hardware and keying.

E. Automatic Operator Supplier Qualifications: Power operator products and accessories are required to be supplied and installed through current members of the manufacturer's "Power Operator Preferred Installer" program. Suppliers are to be factory trained, certified, and a direct purchaser of the specified power operators and be responsible for the installation and maintenance of the units and accessories indicated for the Project.

F. Source Limitations: Obtain each type and variety of door hardware specified in this section from a single source unless otherwise indicated.

1. Electrified modifications or enhancements made to a source manufacturer's product line by a secondary or third party source will not be accepted.

2. Provide electromechanical door hardware from the same manufacturer as mechanical door hardware, unless otherwise indicated.

G. Each unit to bear third party permanent label demonstrating compliance with the referenced standards.

H. Keying Conference: Conduct conference to comply with requirements in Division 01 Section "Project Meetings." Keying conference to incorporate the following criteria into the final keying schedule document:

1. Function of building, purpose of each area and degree of security required. 2. Plans for existing and future key system expansion. 3. Requirements for key control storage and software. 4. Installation of permanent keys, cylinder cores and software. 5. Address and requirements for delivery of keys.

I. Pre-Submittal Conference: Conduct coordination conference in compliance with requirements in Division 01 Section "Project Meetings" with attendance by representatives of Supplier(s), Installer(s), and Contractor(s) to review proper methods and the procedures for receiving, handling, and installing door hardware.

1. Prior to installation of door hardware, conduct a project specific training meeting to instruct the installing contractors' personnel on the proper installation and adjustment of their respective products. Product training to be attended by installers of door hardware (including electromechanical hardware) for aluminum, hollow metal and wood doors. Training will include the use of installation manuals, hardware schedules, templates and physical product samples as required. 2. Inspect and discuss electrical roughing-in, power supply connections, and other preparatory work performed by other trades.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 5 of 32

3. Review sequence of operation narratives for each unique access controlled opening. 4. Review and finalize construction schedule and verify availability of materials. 5. Review the required inspecting, testing, commissioning, and demonstration procedures

J. At completion of installation, provide written documentation that components were applied to manufacturer's instructions and recommendations and according to approved schedule.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Inventory door hardware on receipt and provide secure lock-up and shelving for door hardware delivered to Project site. Do not store electronic access control hardware, software or accessories at Project site without prior authorization.

B. Tag each item or package separately with identification related to the final Door Hardware Schedule, and include basic installation instructions with each item or package.

C. Deliver, as applicable, permanent keys, cylinders, cores, access control credentials, software and related accessories directly to Owner via registered mail or overnight package service. Instructions for delivery to the Owner shall be established at the "Keying Conference".

1.6 COORDINATION

A. Templates: Obtain and distribute to the parties involved templates for doors, frames, and other work specified to be factory prepared for installing standard and electrified hardware. Check Shop Drawings of other work to confirm that adequate provisions are made for locating and installing hardware to comply with indicated requirements.

B. Door Hardware and Electrical Connections: Coordinate the layout and installation of scheduled electrified door hardware and related access control equipment with required connections to source power junction boxes, low voltage power supplies, detection and monitoring hardware, and fire and detection alarm systems.

C. Door and Frame Preparation: Doors and corresponding frames are to be prepared, reinforced and pre-wired (if applicable) to receive the installation of the specified electrified, monitoring, signaling and access control system hardware without additional in-field modifications.

1.7 WARRANTY

A. General Warranty: Reference Division 01, General Requirements. Special warranties specified in this Article shall not deprive Owner of other rights Owner may have under other provisions of the Contract Documents and shall be in addition to, and run

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 6 of 32

concurrent with, other warranties made by Contractor under requirements of the Contract Documents.

B. Warranty Period: Written warranty, executed by manufacturer(s), agreeing to repair or replace components of standard and electrified door hardware that fails in materials or workmanship within specified warranty period after final acceptance by the Owner. Failures include, but are not limited to, the following:

1. Structural failures including excessive deflection, cracking, or breakage. 2. Faulty operation of the hardware. 3. Deterioration of metals, metal finishes, and other materials beyond normal weathering. 4. Electrical component defects and failures within the systems operation.

C. Standard Warranty Period: One year from date of Substantial Completion, unless otherwise indicated.

D. Special Warranty Periods:

1. Ten years for mortise locks and latches. 2. Five years for exit hardware. 3. Twenty five years for manual overhead door closer bodies. 4. Five years for motorized electric latch retraction exit devices. 5. Two years for electromechanical door hardware.

1.8 MAINTENANCE SERVICE

A. Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Owner's continued adjustment, maintenance, and removal and replacement of door hardware.

PART 2 - PRODUCTS

2.1 SCHEDULED DOOR HARDWARE

A. General: Provide door hardware for each door to comply with requirements in Door Hardware Sets and each referenced section that products are to be supplied under.

B. Designations: Requirements for quantity, item, size, finish or color, grade, function, and other distinctive qualities of each type of door hardware are indicated in the Door Hardware Sets at the end of Part 3. Products are identified by using door hardware designations, as follows:

1. Named Manufacturer's Products: Product designation and manufacturer are listed for each door hardware type required for the purpose of establishing requirements. Manufacturers' names are abbreviated in the Door Hardware Schedule.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 7 of 32

C. Substitutions: Requests for substitution and product approval for inclusive mechanical and electromechanical door hardware in compliance with the specifications must be submitted in writing and in accordance with the procedures and time frames outlined in Division 01, Substitution Procedures. Approval of requests is at the discretion of the architect, owner, and their designated consultants.

2.2 HANGING DEVICES

A. Hinges: ANSI/BHMA A156.1 certified butt hinges with number of hinge knuckles and other options as specified in the Door Hardware Sets.

1. Quantity: Provide the following hinge quantity:

a. Two Hinges: For doors with heights up to 60 inches. b. Three Hinges: For doors with heights 61 to 90 inches. c. Four Hinges: For doors with heights 91 to 120 inches. d. For doors with heights more than 120 inches, provide 4 hinges, plus 1 hinge for every 30 inches of door height greater than 120 inches.

2. Hinge Size: Provide the following, unless otherwise indicated, with hinge widths sized for door thickness and clearances required:

a. Widths up to 3’0”: 4-1/2” standard or heavy weight as specified. b. Sizes from 3’1” to 4’0”: 5” standard or heavy weight as specified.

3. Hinge Weight and Base Material: Unless otherwise indicated, provide the following:

a. Exterior Doors: Heavy weight, non-ferrous, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate standard weight. b. Interior Doors: Standard weight, steel, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate heavy weight.

4. Hinge Options: Comply with the following:

a. Non-removable Pins: Provide set screw in hinge barrel that, when tightened into a groove in hinge pin, prevents removal of pin while door is closed; for the all out-swinging lockable doors.

5. Manufacturers:

a. Bommer Industries (BO). b. Hager Companies (HA). c. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - MacPro Series.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 8 of 32

2.3 POWER TRANSFER DEVICES

A. Electrified Quick Connect Transfer Hinges: Provide electrified transfer hinges with Molex™ standardized plug connectors and sufficient number of concealed wires (up to 12) to accommodate the electrified functions specified in the Door Hardware Sets. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Wire nut connections are not acceptable.

1. Manufacturers:

a. Hager Companies (HA) - ETW-QC (# wires) Option. b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - QC (# wires) Option.

B. Electric Door Wire Harnesses: Provide electric/data transfer wiring harnesses with standardized plug connectors to accommodate up to twelve (12) wires. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Provide sufficient number and type of concealed wires to accommodate electric function of specified hardware. Provide a connector for through- door electronic locking devices and from hinge to junction box above the opening. Wire nut connections are not acceptable. Determine the length required for each electrified hardware component for the door type, size and construction, minimum of two per electrified opening.

1. Provide one each of the following tools as part of the base bid contract:

a. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - Electrical Connecting Kit: QC-R001. b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - Connector Hand Tool: QC-R003.

2. Manufacturers:

a. Hager Companies (HA) - Quick Connect. b. McKinney Products; ASSA ABLOY Architectural Door Accessories (MK) - QC-C Series.

2.4 DOOR OPERATING TRIM

A. Flush Bolts and Surface Bolts: ANSI/BHMA A156.3 and A156.16, Grade 1, certified.

1. Flush bolts to be furnished with top rod of sufficient length to allow bolt retraction device location approximately six feet from the floor. 2. Furnish dust proof strikes for bottom bolts. 3. Surface bolts to be minimum 8” in length and U.L. listed for labeled fire doors and U.L. listed for windstorm components where applicable. 4. Provide related accessories (mounting brackets, strikes, coordinators, etc.) as required for appropriate installation and operation.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 9 of 32

5. Manufacturers:

a. Burns Manufacturing (BU). b. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO). c. Trimco (TC).

B. Door Push Plates and Pulls: ANSI/BHMA A156.6 certified door pushes and pulls of type and design specified in the Hardware Sets. Coordinate and provide proper width and height as required where conflicting hardware dictates.

1. Push/Pull Plates: Minimum .050 inch thick, size as indicated in hardware sets, with beveled edges, secured with exposed screws unless otherwise indicated. 2. Door Pull and Push Bar Design: Size, shape, and material as indicated in the hardware sets. Minimum clearance of 2 1/2-inches from face of door unless otherwise indicated. 3. Offset Pull Design: Size, shape, and material as indicated in the hardware sets. Minimum clearance of 2 1/2-inches from face of door and offset of 90 degrees unless otherwise indicated. 4. Fasteners: Provide manufacturer's designated fastener type as indicated in Hardware Sets.

5. Manufacturers:

a. Burns Manufacturing (BU). b. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO). c. Trimco (TC).

2.5 CYLINDERS AND KEYING

A. General: Cylinder manufacturer to have minimum (10) years experience designing secured master key systems and have on record a published security keying system policy. 1. Manufacturers:

a. Match Existing, Field Verify. b. No Substitution.

B. Cylinder Types: Original manufacturer cylinders able to supply the following cylinder formats and types:

1. Threaded mortise cylinders with rings and cams to suit hardware application. 2. Rim cylinders with back plate, flat-type vertical or horizontal tailpiece, and raised trim ring. 3. Bored or cylindrical lock cylinders with tailpieces as required to suit locks. 4. Tubular deadlocks and other auxiliary locks. 5. Mortise and rim cylinder collars to be solid and recessed to allow the cylinder face to be flush and be free spinning with matching finishes. 6. Keyway: Match Facility Restricted Keyway.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 10 of 32

C. Permanent Cores: Match standard. Reference Division 01 "Cash Allowances" for material required under project. Installation to be included under Division 08 "Door Hardware" base bid package.

D. Keying System: Each type of lock and cylinders to be factory keyed.

1. Supplier shall conduct a "Keying Conference" to define and document keying system instructions and requirements. 2. Furnish factory cut, nickel-silver large bow permanently inscribed with a visual key control number as directed by Owner. 3. Existing System: Field verify and key cylinders to match Owner's existing system.

E. Key Quantity: Provide the following minimum number of keys:

1. Change Keys per Cylinder: Two (2) 2. Master Keys (per Master Key Level/Group): Five (5).

F. Construction Keying: Provide construction master keyed cylinders.

G. Key Registration List (Bitting List):

1. Provide keying transcript list to Owner's representative in the proper format for importing into key control software. 2. Provide transcript list in writing or electronic file as directed by the Owner.

2.6 MECHANICAL LOCKS AND LATCHING DEVICES

A. Mortise Locksets, Grade 1 (Heavy Duty): ANSI/BHMA A156.13, Series 1000, Operational Grade 1 Certified Products Directory (CPD) listed. Locksets are to be manufactured with a corrosion resistant steel case and be field-reversible for handing without disassembly of the lock body.

1. Where specified, provide status indicators with highly reflective color and wording for “locked/unlocked” or “vacant/occupied” with custom wording options if required. Indicator to be located above the cylinder with the inside thumb-turn not blocking the visibility of the indicator status. Indicator window size to be a minimum of 2.1” x 0.6” with a curved design allowing a 180 degree viewing angle with protective covering to prevent tampering.

2. Manufacturers:

a. Sargent Manufacturing (SA) - 8200 Series. b. Schlage (SC) - L9000 Series.

2.1 INTEGRATED WIRED OUTPUT LOCKING DEVICES – MULTI-CLASS READER

A. Integrated Wired Output Multi-Class Mortise Locks: Wiegand or Open Supervised Device Protocol (OSDP) output ANSI A156.13, Grade 1, mortise lockset with

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 11 of 32

integrated card reader with or without keypad option, request-to-exit signaling, door position status switch, and latchbolt monitoring in one complete unit. Hard wired, solenoid driven locking/unlocking control of the lever handle trim, 3/4" deadlocking antifriction latch, and 1" case-hardened steel deadbolt. Lock is U.L listed and labeled for use on up to 3 hour fire rated openings. Available with or without keyed high security cylinder override.

1. Open architecture, hard wired platform supports centralized control of locking units with new or existing Wiegand or OSDP compatible access control systems. Latchbolt monitoring and door position switch act in conjunction to report door-in- frame (DPS) and door latched (door closed and latched) conditions. 2. Integrated reader supports the following credentials:

a. 125kHz proximity credentials: HID, AWID, Indala, and EM4102. b. 13.56 MHz proximity credentials: HID Secure Identity Object™ (SIO) on iCLASS Seos, HID iCLASS, HID iCLASS SE/SR, MIFARE Classic, DESFire EV1 and EV2. c. 2.4 GHz credentials: Secure Identity Object™ (SIO) on Mobile IDs (Bluetooth Smart) d. ISO14443A/B (PIV-compatible Transparent FASC-N read) available with pivCLASS variant e. NFC-enabled mobile phones f. PIN code only or PIN + credential with keypad option.

3. 12VDC external power supply required for reader and lock, with optional 24VDC lock solenoid. Fail safe or fail secure options. 4. Energy Efficient Design: Provide lock bodies which have a holding current draw of 500mA maximum, and can operate on either 12 or 24 volts. Locks are to be field configurable for fail safe or fail secure operation. 5. Support end-of-line resistors contained within the lock case. 6. Installation requires only one cable run from the lock to the access control panel without requirements for additional proprietary lock panel interface boards or modules. 7. Installation to include manufacturer's access control panel interface board or module where required for Wiegand or OSDP output protocol.

8. Manufacturers:

a. Corbin Russwin (RU) – ML2000 SN Series. b. Sargent Manufacturing (SA) – SN200/SN210 8200 Series.

2.2 LOCK AND LATCH STRIKES

A. Strikes: Provide manufacturer's standard strike with strike box for each latch or lock bolt, with curved lip extended to protect frame, finished to match door hardware set, unless otherwise indicated, and as follows:

1. Flat-Lip Strikes: For locks with three-piece antifriction latchbolts, as recommended by manufacturer.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 12 of 32

2. Extra-Long-Lip Strikes: For locks used on frames with applied wood casing trim. 3. Aluminum-Frame Strike Box: Provide manufacturer's special strike box fabricated for aluminum framing. 4. Double-lipped strikes: For locks at double acting doors. Furnish with retractable stop for rescue hardware applications.

B. Standards: Comply with the following:

1. Strikes for Mortise Locks and Latches: BHMA A156.13. 2. Strikes for Bored Locks and Latches: BHMA A156.2. 3. Strikes for Auxiliary Deadlocks: BHMA A156.36. 4. Dustproof Strikes: BHMA A156.16.

2.3 CONVENTIONAL EXIT DEVICES

A. General Requirements: All exit devices specified herein shall meet or exceed the following criteria:

1. At doors not requiring a fire rating, provide devices complying with NFPA 101 and listed and labeled for "Panic Hardware" according to UL305. Provide proper fasteners as required by manufacturer including sex nuts and bolts at openings specified in the Hardware Sets.

2. Where exit devices are required on fire rated doors, provide devices complying with NFPA 80 and with UL labeling indicating "Fire Exit Hardware". Provide devices with the proper fasteners for installation as tested and listed by UL. Consult manufacturer’s catalog and template book for specific requirements.

3. Except on fire rated doors, provide exit devices with hex key dogging device to hold the pushbar and latch in a retracted position. Provide optional keyed cylinder dogging on devices where specified in Hardware Sets.

4. Devices must fit flat against the door face with no gap that permits unauthorized dogging of the push bar. The addition of filler strips is required in any case where the door light extends behind the device as in a full glass configuration.

5. Lever Operating Trim: Where exit devices require lever trim, furnish manufacturer's heavy duty escutcheon trim with threaded studs for thru-bolts.

a. Lock Trim Design: As indicated in Hardware Sets, provide finishes and designs to match that of the specified locksets. b. Where function of exit device requires a cylinder, provide a cylinder (Rim or Mortise) as specified in Hardware Sets.

6. Vertical Rod Exit Devices: Where surface or concealed vertical rod exit devices are used at interior openings, provide as less bottom rod (LBR) unless otherwise indicated. Provide dust proof strikes where thermal pins are required to project into the floor.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 13 of 32

7. Narrow Stile Applications: At doors constructed with narrow stiles, or as specified in Hardware Sets, provide devices designed for maximum 2” wide stiles.

8. Dummy Push Bar: Nonfunctioning push bar matching functional push bar.

9. Rail Sizing: Provide exit device rails factory sized for proper door width application.

10. Through Bolt Installation: For exit devices and trim as indicated in Door Hardware Sets.

B. Conventional Push Rail Exit Devices (Heavy Duty): ANSI/BHMA A156.3, Grade 1 Certified Products Directory (CPD) listed panic and fire exit hardware devices furnished in the functions specified in the Hardware Sets. Exit device latch to be stainless steel, pullman type, with deadlock feature.

1. Manufacturers:

a. Sargent Manufacturing (SA) - 80 Series. b. Von Duprin (VD) - 35A/98 XP Series.

2.4 INTEGRATED WIRED OUTPUT EXIT DEVICES - MULTI-CLASS READER

A. Integrated Wired Output Multi-Class Exit Hardware: Wiegand output ANSI 156.3 Grade 1 rim, mortise, and vertical rod exit device hardware with integrated card reader with or without keypad option, latchbolt and touchbar monitoring, and request-to-exit signaling, in one complete unit. Hard wired, solenoid driven locking/unlocking control of the lever handle exit trim with 3/4" throw latch bolt. U.L listed and labeled for either panic or "fire exit hardware" for use on up to 3 hour fire rated openings. Available with or without keyed high security cylinder override.

1. Open architecture, hard wired platform supports centralized control of locking units with new or existing Wiegand or OSDP compatible access control systems. Inside push bar (request-to-exit) signaling and door position (open/closed status) monitoring (via separately connected DPS). 2. Integrated reader supports the following credentials:

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 14 of 32

3. 12VDC external power supply required for reader. 24VDC required for solenoid operated exit trim. Fail safe or fail secure options. 4. Installation requires only one cable run from the exit hardware to the access control panel without requirements for additional proprietary lock panel interface boards or modules. 5. Competitor Alternates Allowed Option: Installation to include manufacturer's access control panel interface board or module where required for Wiegand or OSDP output protocol.

6. Manufacturers:

a. Corbin Russwin (RU) – ED5000 SN Series. b. Sargent Manufacturing (SA) – SN200/SN210 80 Series.

2.5 DOOR CLOSERS

A. All door closers specified herein shall meet or exceed the following criteria:

1. General: Door closers to be from one manufacturer, matching in design and style, with the same type door preparations and templates regardless of application or spring size. Closers to be non-handed with full sized covers.

2. Standards: Closers to comply with UL-10C for Positive Pressure Fire Test and be U.L. listed for use of fire rated doors.

3. Size of Units: Comply with manufacturer's written recommendations for sizing of door closers depending on size of door, exposure to weather, and anticipated frequency of use. Where closers are indicated for doors required to be accessible to the Americans with Disabilities Act, provide units complying with ANSI ICC/A117.1.

4. Closer Arms: Provide heavy duty, forged steel closer arms unless otherwise indicated in Hardware Sets.

5. Closers shall not be installed on exterior or corridor side of doors; where possible install closers on door for optimum aesthetics.

6. Closer Accessories: Provide door closer accessories including custom templates, special mounting brackets, spacers and drop plates as required for proper installation. Provide through-bolt and security type fasteners as specified in the hardware sets.

B. Door Closers, Surface Mounted (Heavy Duty): ANSI/BHMA A156.4, Grade 1 Certified Products Directory (CPD) listed surface mounted, heavy duty door closers with complete spring power adjustment, sizes 1 thru 6; and fully operational adjustable according to door size, frequency of use, and opening force. Closers to be rack and pinion type, one piece cast iron or aluminum alloy body construction, with adjustable backcheck and separate non-critical valves for closing sweep and latch speed control. Provide non-handed units standard.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 15 of 32

1. Manufacturers:

a. Corbin Russwin Hardware (RU) - DC6000 Series. b. Norton Door Controls (NO) - 7500 Series. c. Sargent Manufacturing (SA) - 351 Series.

C. Door Closers, Surface Mounted (Commercial Duty): ANSI/BHMA 156.4, Grade 1 Certified Products Directory (CPD) listed surface mounted, institutional grade door closers with complete spring power adjustment, sizes 1 thru 6; and fully operational adjustable according to door size, frequency of use, and opening force. Closers to be rack and pinion type, one piece cast iron or aluminum alloy body construction, with adjustable backcheck, closing sweep, and latch speed control valves. Provide non- handed units standard.

1. Manufacturers:

a. Corbin Russwin Hardware (RU) - DC6000 Series. b. Norton Door Controls (NO) - 8500 Series. c. Sargent Manufacturing (SA) - 1431 Series.

2.6 ELECTROHYDRAULIC DOOR OPERATORS

A. General: Provide low energy operators of size recommended by manufacturer for door size, weight, and movement; for condition of exposure; and for compliance with UL 325. Coordinate operator mechanisms with door operation, hinges, and activation devices.

1. Fire-Rated Doors: Provide door operators for fire-rated door assemblies that comply with NFPA 80 for fire-rated door components and are listed and labeled by a qualified testing agency.

B. Standard: Certified ANSI/BHMA A156.19.

C. Performance Requirements:

1. Opening Force if Power Fails: Not more than 15 lbf required to release a latch if provided, not more than 30 lbf required to manually set door in motion, and not more than 15 lbf required to fully open door. 2. Entrapment Protection: Not more than 15 lbf required to prevent stopped door from closing or opening.

D. Configuration: Surface mounted or in-ground as required. Door operators to control single swinging and pair of swinging doors.

E. Operation: Power opening and spring closing operation capable of meeting ANSI A117.1 accessibility guideline. Provide time delay for door to remain open before initiating closing cycle as required by ANSI/BHMA A156.19. When not in automatic mode, door operator to function as manual door closer with fully adjustable opening and closing forces, with or without electrical power.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 16 of 32

F. Features: Operator units to have full feature adjustments for door opening and closing force and speed, backcheck, motor assist acceleration from 0 to 30 seconds, time delay, vestibule interface delay, obstruction recycle, and hold open time from 0 up to 30 seconds.

G. Provide outputs and relays on board the operator to allow for coordination of exit device latch retraction, electric strikes, magnetic locks, card readers, safety and motion sensors and specified auxiliary contacts.

H. Brackets and Reinforcements: Manufacturer's standard, fabricated from aluminum with nonferrous shims for aligning system components.

I. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. LCN Closers (LC) - 4640 Series. 2. Norton Door Controls (NO) - 6000 Series.

2.7 ARCHITECTURAL TRIM

A. Door Protective Trim

1. General: Door protective trim units to be of type and design as specified below or in the Hardware Sets.

2. Size: Fabricate protection plates (kick, armor, or mop) not more than 2" less than door width (LDW) on stop side of single doors and 1” LDW on stop side of pairs of doors, and not more than 1" less than door width on pull side. Coordinate and provide proper width and height as required where conflicting hardware dictates. Height to be as specified in the Hardware Sets.

3. Where plates are applied to fire rated doors with the top of the plate more than 16” above the bottom of the door, provide plates complying with NFPA 80. Consult manufacturer’s catalog and template book for specific requirements for size and applications.

4. Protection Plates: ANSI/BHMA A156.6 certified protection plates (kick, armor, or mop), fabricated from the following:

a. Stainless Steel: 300 grade, 050-inch thick.

5. Options and fasteners: Provide manufacturer's designated fastener type as specified in the Hardware Sets. Provide countersunk screw holes.

6. Manufacturers:

a. Hiawatha, Inc. (HI). b. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO). c. Trimco (TC).

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 17 of 32

2.8 DOOR STOPS AND HOLDERS

A. General: Door stops and holders to be of type and design as specified below or in the Hardware Sets.

B. Door Stops and Bumpers: ANSI/BHMA A156.16, Grade 1 certified door stops and wall bumpers. Provide wall bumpers, either convex or concave types with anchorage as indicated, unless floor or other types of door stops are specified in Hardware Sets. Do not mount floor stops where they will impede traffic. Where floor or wall bumpers are not appropriate, provide overhead type stops and holders.

1. Manufacturers:

a. Hiawatha, Inc. (HI). b. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO). c. Trimco (TC).

C. Overhead Door Stops and Holders: ANSI/BHMA A156.8, Grade 1 Certified Products Directory (CPD) listed overhead stops and holders to be surface or concealed types as indicated in Hardware Sets. Track, slide, arm and jamb bracket to be constructed of extruded bronze and shock absorber spring of heavy tempered steel. Provide non- handed design with mounting brackets as required for proper operation and function.

1. Manufacturers:

a. Rixson Door Controls (RF). b. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO). c. Sargent Manufacturing (SA).

2.9 ARCHITECTURAL SEALS

A. General: Thresholds, weatherstripping, and gasket seals to be of type and design as specified below or in the Hardware Sets. Provide continuous weatherstrip gasketing on exterior doors and provide smoke, light, or sound gasketing on interior doors where indicated. At exterior applications provide non-corrosive fasteners and elsewhere where indicated.

B. Smoke Labeled Gasketing: Assemblies complying with NFPA 105 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for smoke control ratings indicated, based on testing according to UL 1784.

1. Provide smoke labeled perimeter gasketing at all smoke labeled openings.

C. Fire Labeled Gasketing: Assemblies complying with NFPA 80 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to UL-10C.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 18 of 32

1. Provide intumescent seals as indicated to meet UL10C Standard for Positive Pressure Fire Tests of Door Assemblies, and NPFA 252, Standard Methods of Fire Tests of Door Assemblies.

D. Sound-Rated Gasketing: Assemblies that are listed and labeled by a testing and inspecting agency, for sound ratings indicated.

E. Replaceable Seal Strips: Provide only those units where resilient or flexible seal strips are easily replaceable and readily available from stocks maintained by manufacturer.

F. Manufacturers:

1. Pemko Products; ASSA ABLOY Architectural Door Accessories (PE). 2. Reese Enterprises, Inc. (RE). 3. Zero (ZE).

2.10 ELECTRONIC ACCESSORIES

A. Door Position Switches: Door position magnetic reed contact switches specifically designed for use in commercial door applications. On recessed models the contact and magnetic housing snap-lock into a 1" diameter hole. Surface mounted models include wide gap distance design complete with armored flex cabling. Provide SPDT, N/O switches with optional Rare Earth Magnet installation on steel doors with flush top channels.

1. Manufacturers:

a. Sargent Manufacturing (SA) - 3280 Series. b. Securitron (SU) - DPS Series.

B. Wiegand Test Unit: Test unit verifies proper Wiegand output integrated card reader lock installation in the field by testing for proper wiring, card reader data integrity, and lock functionality including lock/unlock, door position, and request-to-exit status. 12 or 24VDC voltage adjustable operating as Fail Safe or Fail Secure.

1. Manufacturers:

a. Corbin Russwin Hardware (RU) - WT2 Wiegand Test Unit. b. Sargent Manufacturing (SA) - WT2 Wiegand Test Unit.

C. Switching Power Supplies: Provide power supplies with either single or dual voltage configurations at 12 or 24VDC. Power supplies shall have battery backup function with an integrated battery charging circuit and shall provide capability for power distribution, direct lock control and Fire Alarm Interface (FAI) through add on modules. Power supplies shall be expandable up to 16 individually protected outputs. Output modules shall provide individually protected, continuous outputs and/or individually protected, relay controlled outputs.

1. Manufacturers:

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 19 of 32

a. Securitron (SU) - AQD Series.

2.11 FABRICATION

A. Fasteners: Provide door hardware manufactured to comply with published templates generally prepared for machine, wood, and sheet metal screws. Provide screws according to manufacturers recognized installation standards for application intended.

2.12 FINISHES

A. Standard: Designations used in the Hardware Sets and elsewhere indicate hardware finishes complying with ANSI/BHMA A156.18, including coordination with traditional U.S. finishes indicated by certain manufacturers for their products.

B. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer's standards, but in no case less than specified by referenced standards for the applicable units of hardware

C. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine scheduled openings, with Installer present, for compliance with requirements for installation tolerances, labeled fire door assembly construction, wall and floor construction, and other conditions affecting performance.

B. Notify architect of any discrepancies or conflicts between the door schedule, door types, drawings and scheduled hardware. Proceed only after such discrepancies or conflicts have been resolved in writing.

3.2 PREPARATION

A. Hollow Metal Doors and Frames: Comply with ANSI/DHI A115 series.

B. Wood Doors: Comply with ANSI/DHI A115-W series.

3.3 INSTALLATION

A. Install each item of mechanical and electromechanical hardware and access control equipment to comply with manufacturer's written instructions and according to specifications.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 20 of 32

1. Installers are to be trained and certified by the manufacturer on the proper installation and adjustment of fire, life safety, and security products including: hanging devices; locking devices; closing devices; and seals.

B. Mounting Heights: Mount door hardware units at heights indicated in following applicable publications, unless specifically indicated or required to comply with governing regulations:

1. Standard Steel Doors and Frames: DHI's "Recommended Locations for Architectural Hardware for Standard Steel Doors and Frames." 2. Wood Doors: DHI WDHS.3, "Recommended Locations for Architectural Hardware for Wood Flush Doors." 3. Where indicated to comply with accessibility requirements, comply with ANSI A117.1 "Accessibility Guidelines for Buildings and Facilities." 4. Provide blocking in drywall partitions where wall stops or other wall mounted hardware is located.

C. Retrofitting: Install door hardware to comply with manufacturer's published templates and written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work specified in Division 9 Sections. Do not install surface-mounted items until finishes have been completed on substrates involved.

D. Thresholds: Set thresholds for exterior and acoustical doors in full bed of sealant complying with requirements specified in Division 7 Section "Joint Sealants."

E. Storage: Provide a secure lock up for hardware delivered to the project but not yet installed. Control the handling and installation of hardware items so that the completion of the work will not be delayed by hardware losses before and after installation.

3.4 FIELD QUALITY CONTROL

A. Field Inspection (Punch Report): Reference Division 01 Sections “Closeout Procedures”. Produce project punch report for each installed door opening indicating compliance with approved submittals and verification hardware is properly installed, operating and adjusted. Include list of items to be completed and corrected, indicating the reasons or deficiencies causing the Work to be incomplete or rejected.

1. Organization of List: Include separate Door Opening and Deficiencies and Corrective Action Lists organized by Mark, Opening Remarks and Comments, and related Opening Images and Video Recordings. 2. Submit documentation of incomplete items in the following formats:

a. PDF electronic file. b. Electronic formatted file integrated with the Openings Studio™ door opening management software platform.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 21 of 32

3.5 ADJUSTING

A. Initial Adjustment: Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements.

3.6 CLEANING AND PROTECTION

A. Protect all hardware stored on construction site in a covered and dry place. Protect exposed hardware installed on doors during the construction phase. Install any and all hardware at the latest possible time frame.

B. Clean adjacent surfaces soiled by door hardware installation.

C. Clean operating items as necessary to restore proper finish. Provide final protection and maintain conditions that ensure door hardware is without damage or deterioration at time of owner occupancy.

3.7 DEMONSTRATION

A. Instruct Owner's maintenance personnel to adjust, operate, and maintain mechanical and electromechanical door hardware.

3.8 DOOR HARDWARE SETS

A. The hardware sets represent the design intent and direction of the owner and architect. They are a guideline only and should not be considered a detailed hardware schedule. Discrepancies, conflicting hardware and missing items should be brought to the attention of the architect with corrections made prior to the bidding process. Omitted items not included in a hardware set should be scheduled with the appropriate additional hardware required for proper application and functionality.

1. Quantities listed are for each pair of doors, or for each single door.

2. The supplier is responsible for handing and sizing all products.

3. Where multiple options for a piece of hardware are given in a single line item, the supplier shall provide the appropriate application for the opening.

4. At existing openings with new hardware the supplier shall field inspect existing conditions prior to the submittal stage to verify the specified hardware will work as required. Provide alternate solutions and proposals as needed.

B. Manufacturer’s Abbreviations:

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 22 of 32

1. MK - McKinney 2. RO - Rockwood 3. SA - SARGENT 4. SC - Schlage 5. RU - Corbin Russwin 6. RF - Rixson 7. NO - Norton 8. PE - Pemko 9. MC - Medeco 10. SU - Securitron 11. LU - Lund Equipment Co 12. OT - Other

Hardware Sets

Set: 1.0 Doors: 155

2 Hinge (heavy weight) MPB99 (NRP and size as required) US32D MK MPB99-QCx (# of Wires and Size as 1 Electric Hinge, Hvy Wt US32D MK Required) Rim Exit Device (EL Trim F.SEC, 16 56-SN200 8876 (24v) (BIPS) ETP 1 US32D SA RX, ELR, CD) (Cyl. Dogging) Size and Cam or Tailpeice as 2 Rim or Mortised Cylinder Housing 626 SC required 2 LFIC Mortise Cylinder Housing Size and Cam as required US32D SA 1 Automatic Opener 6011/21 (As Required) 689 NO 1 Kick Plate K1050 10" high BEV CSK US32D RO 273x224AFGT x Length Required x 1 Threshold PE MSES25SS 1 Gasketing 303AS (Head & Jambs) PE 1 Rain Guard 346C x Width of Frame Head PE 1 Sweep 3452CNB x Length Required PE 1 Harness Adaptor 52-2946 SA 1 ElectroLynx Harness QC-C**** x Length Required MK 1 ElectroLynx Harness QC-C3000P MK 2 Auto Operator Actuator Switch 505 NO 1 Position Switch DPS2 - M / W-BK SU

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 23 of 32

1 Power Supply AQD (Size and Options as required) SU 1 Wiring Diagram Elevation and Point to Point OT

Notes: Operation: • Doors are normally closed and secure. • When there is an authorized card read on the secured side of the door, the exit device latch will retract and the auto operator actuator button will become active. Pressing the auto operator actuator button (after authorized card read) will signal the auto operator to open the door to allow entry. • On the unsecured side of the opening, pressing the auto operator actuator button will signal exit latch to retract and the auto operator to open the door to allow egress. • Manual egress is always available by pushing on the exit device push bar. • Exit device is fail secure and will remain latched in the event of a fire alarm or power outage.

Set: 2.0 Doors: 131E

3 Hinge (heavy weight) MPB99 (NRP and size as required) US32D MK 1 Rim Exit Device (EO) LD 8810 EO (Less Dogging) US32D SA 1 Surface Closer 351 CPS (PA SPG SPT Arm) EN SA 1 Kick Plate K1050 10" high BEV CSK US32D RO 273x224AFGT x Length Required x 1 Threshold PE MSES25SS 1 Gasketing 303AS (Head & Jambs) PE 1 Rain Guard 346C x Width of Frame Head PE 1 Sweep 3452CNB x Length Required PE 1 Position Switch DPS2 - M / W-BK SU

Notes: System Operational Narrative: • Door normally closed and secure. • Door position switch provides open/closed monitoring to both access control system and intrusion alarm service.

Set: 3.0 Doors: 131C, 137

5 Hinge (heavy weight) MPB99 (NRP and size as required) US32D MK MPB99-QCx (# of Wires and Size as 1 Electric Hinge, Hvy Wt US32D MK Required) 1 Self Latching Flush Bolt Set 2845 / 2945 (as required) US26D RO 1 Dust Proof Strike 570 US26D RO 1 Access Control Lock SN200 82271 (24v) (BIPS) LNP US26D SA

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 24 of 32

Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1 Primus Cylinder Core Keyed to Owners Existing System 626 SC 2 Conc Overhead Stop 1-X36 (Size as Required) 630 RF 351 UO (Reg or PA Arm as 2 Surface Closer (Tri-Pack) EN SA Required) 2 Kick Plate K1050 10" high BEV CSK US32D RO 172A x Length Required x 1 Threshold PE MSES25SS 1 Gasketing 303AS (Head & Jambs) PE 1 Rain Guard 346C x Width of Frame Head PE 2 Sweep 3452CNB x Length Required PE 2 Astragal 29324CNB x Door Height PE 1 ElectroLynx Harness QC-C**** x Length Required MK 1 ElectroLynx Harness QC-C3000P MK 2 Position Switch DPS2 - M / W-BK SU 1 Power Supply AQD (Size and Options as required) SU 1 Wiring Diagram Elevation and Point to Point OT

Notes: System Operational Narrative: • Doors normally closed and secure. • Access by valid credential presentation releasing the lockset lever for a pre-determined time limit and then relocking. • Egress always free for immediate exit. Request-to-Exit sensors allows exit without alarm condition. • Door position switches provide open/closed monitoring to both access control system and intrusion alarm service. • Lever remain locked (fail secure) in event of power loss. Key override cylinder for emergency access.

Set: 4.0 Doors: 157

3 Hinge (heavy weight) MPB99 (NRP and size as required) US32D MK 1 Storeroom/Closet Lock LC 8204 LSP US32D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1 Primus Cylinder Core Keyed to Owners Existing System 626 SC 351 UO (Reg or PA Arm as 1 Surface Closer (Tri-Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Wall Stop 403 (or) 441CU (As Required) US26D RO

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 25 of 32

273x224AFGT x Length Required x 1 Threshold PE MSES25SS 1 Gasketing 303AS (Head & Jambs) PE 1 Rain Guard 346C x Width of Frame Head PE 1 Sweep 3452CNB x Length Required PE 1 Position Switch DPS2 - M / W-BK SU

Notes: System Operational Narrative: • Door normally closed and secure. • Door position switch provides open/closed monitoring to both access control system and intrusion alarm service.

Set: 5.0 Doors: 115

2 Hinge, Full Mortise, Hvy Wt MPB68 (NRP and Size as required) US26D MK MPB68 QCx (# of Wires as 1 Hinge (heavy weight) US26D MK Required) Rim Exit Device (EL Trim F.SEC, 16 56-SN200 8876 (24v) (BIPS) ETP 1 US32D SA RX, ELR, CD) (Cyl. Dogging) Size and Cam or Tailpeice as 2 Rim or Mortised Cylinder Housing 626 SC required 2 LFIC Mortise Cylinder Housing Size and Cam as required US32D SA 1 Automatic Opener 6011/21 (As Required) 689 NO 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Wall Stop 403 (or) 441CU (As Required) US26D RO 1 Harness Adaptor 52-2946 SA 1 ElectroLynx Harness QC-C**** x Length Required MK 1 ElectroLynx Harness QC-C3000P MK 2 Auto Operator Actuator Switch 505 NO 1 Position Switch DPS2 - M / W-BK SU 1 Power Supply AQD (Size and Options as required) SU 1 Wiring Diagram Elevation and Point to Point OT

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 26 of 32

• Manual egress is always available by pushing on the exit device push bar. • Exit device is fail secure and will remain latched in the event of a fire alarm or power outage.

Set: 6.0 Doors: 134

5 Hinge, Full Mortise, Hvy Wt MPB68 (NRP and Size as required) US26D MK MPB68 QCx (# of Wires as 1 Hinge (heavy weight) US26D MK Required) 1 Self Latching Flush Bolt Set 2845 / 2945 (as required) US26D RO 1 Dust Proof Strike 570 US26D RO 1 Access Control Lock SN200 82271 (24v) (BIPS) LNP US26D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1 Primus Cylinder Core Keyed to Owners Existing System 626 SC 2 Surf Overhead Stop 10-X36 630 RF 1431 UO (Reg or PA Arm as 2 Surface Closer (Tri Pack) EN SA Required) 2 Kick Plate K1050 10" high BEV CSK US32D RO 2 Silencer 608 RO 1 ElectroLynx Harness QC-C**** x Length Required MK 1 ElectroLynx Harness QC-C3000P MK 2 Position Switch DPS2 - M / W-BK SU 1 Power Supply AQD (Size and Options as required) SU 1 Wiring Diagram Elevation and Point to Point OT

Set: 7.0

Not used

Set: 8.0

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 27 of 32

Doors: 143A, 158

2 Hinge, Full Mortise, Hvy Wt MPB68 (NRP and Size as required) US26D MK MPB68 QCx (# of Wires as 1 Hinge (heavy weight) US26D MK Required) 1 Access Control Lock SN200 82271 (24v) (BIPS) LNP US26D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1431 UO (Reg or PA Arm as 1 Surface Closer (Tri Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Wall Stop 403 (or) 441CU (As Required) US26D RO 1 Silencer 608 RO 1 ElectroLynx Harness QC-C**** x Length Required MK 1 ElectroLynx Harness QC-C3000P MK 1 Power Supply AQD (Size and Options as required) SU 1 Wiring Diagram Elevation and Point to Point OT

Notes: System Operational Narrative: • Door normally closed and secure. • Access by valid credential presentation unlocking lever trim for a pre-determined time limit and then relocking. • Egress always free for immediate exit. Request-to-Exit sensor allows exit without alarm condition. • Door position switch provides open/closed monitoring to both access control system and intrusion alarm service. • Outside lever trim remains locked (fail secure) in event of power loss. Key override cylinder for emergency access.

Set: 9.0 Doors: 123, 125, 150, 156

3 Hinge, Full Mortise MPB79 (NRP and size as required) US26D MK 1 Storeroom/Closet Lock LC 8204 LSP US32D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1431 UO (Reg or PA Arm as 1 Surface Closer (Tri Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Wall Stop 403 (or) 441CU (As Required) US26D RO 3 Silencer 608 RO

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 28 of 32

Set: 10.0 Doors: 126, 138

3 Hinge, Full Mortise MPB79 (NRP and size as required) US26D MK 1 Storeroom/Closet Lock LC 8204 LSP US32D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1 Conc Overhead Stop 1-X36 (Size as Required) 630 RF 1431 UO (Reg or PA Arm as 1 Surface Closer (Tri Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 3 Silencer 608 RO

Set: 11.0 Doors: 113, 122, 124, 127, 145, 146, 147, 148, 149, 152, 153, 154

Set: 12.0 Doors: 133

3 Hinge, Full Mortise MPB79 (NRP and size as required) US26D MK 1 Office/Entry Lock LC 8205 LSP US32D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1 Primus Cylinder Core Keyed to Owners Existing System 626 SC 1431 UO (Reg or PA Arm as 1 Surface Closer (Tri Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Wall Stop 403 (or) 441CU (As Required) US26D RO 1 Gasketing S88D (Head & Jambs) PE

Set: 13.0

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 29 of 32

Doors: 142

3 Hinge, Full Mortise MPB79 (NRP and size as required) US26D MK 1 Office/Entry Lock LC 8205 LSP US32D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1431 UO (Reg or PA Arm as 1 Surface Closer (Tri Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Smooth Threshold 151A MSES25SS PE 1 Gasketing S88D (Head & Jambs) PE 1 Perimeter Acoustic Gasket S773BL PE 1 Acoustic Corner Pads ACP112BL/2 PE 1 Acoustic Auto Door Bottom STC411APK 48" PE

Notes: Confirm with Door/Frame manufacturer and architect for required STC Rating and Sound Gaskets.

Set: 14.0 Doors: 128

3 Hinge, Full Mortise MPB79 (NRP and size as required) US26D MK 1 Classroom Lock LC 8237 LSP US32D SA Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1 Primus Cylinder Core Keyed to Owners Existing System 626 SC 1431 UO (Reg or PA Arm as 1 Surface Closer (Tri Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Wall Stop 403 (or) 441CU (As Required) US26D RO 1 Silencer 608 RO

Set: 14.1 Doors: 114

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 30 of 32

1 Kick Plate K1050 10" high BEV CSK US32D RO 3 Silencer 608 RO

Set: 15.0 Doors: 139, 140, 141

3 Hinge, Full Mortise MPB79 (NRP and size as required) US26D MK 1 Privacy Lock w/OCC IND V21 8265 LNP US32D SA 1431 UO (Reg or PA Arm as 1 Surface Closer (Tri Pack) EN SA Required) 1 Kick Plate K1050 10" high BEV CSK US32D RO 1 Wall Stop 403 (or) 441CU (As Required) US26D RO 3 Silencer 608 RO 1 Coat Hook RM801 US26D RO

Set: 16.0 Doors: 109, 110

3 Hinge, Full Mortise MPB79 (NRP and size as required) US26D MK 1 Passage Latch 8215 LSP US32D SA 1 Surf Overhead Stop 10-X36 630 RF 3 Silencer 608 RO

Set: 17.0 Doors: 129A, 131B, 131E

Size and Cam or Tailpeice as 1 Rim or Mortised Cylinder Housing 626 SC required 1 Primus Cylinder Core Keyed to Owners Existing System 626 SC 1 LFIC Cylinder type as required 626 RU All Hardware Provided By Door 1 Supplier

Set: 18.0 Doors: Misc

1 Software KW-SS1 SA 1 Repair Kit QC-R001 MK 1 Crimp Tool QC-R003 MK 1 Test Unit WT2 SA

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 31 of 32

1 Key Management System EA-100117 MC 1 Key Cabinet 1200 Series (capacity as required) LU

Set: 19.0 Doors: 32

Heavy Duty Exterior Rim Exit 1 10XW X03Z X 630/630 X 99 DE Device (NL, LD) Mounting Plate for Gate Rim Exit GATE PLATE by Gate 1 OT Device Manufacturer Mounting Plate for Gate Rim Exit 1 Strike Mounting Plate OT Strike Gate Hardware by Gate Gate mounting Hardware by Gate 1 OT Manufacturer Manufacturer

Set: 20.0 Doors: 33

Heavy Duty Exterior Rim Exit 10xW X 03Z X 630/630 X ER EX 1 DE Device-Fail Sec. (NL, RX, ELR) W X LD X 99 X EC1 X FC10W Rim or Mortised Cylinder Size and Cam or Tailpeice as 1 .626 SC Housing required 1 Primus Cylinder Core Keyed to Owners Existing System .626 SC 1 Card Reader By Security Supplier 1 Power Supply Detex Power Supply DE Mounting Plate for Gate Rim Exit GATE PLATE by Gate 1 OT Device Manufacturer Mounting Plate for Gate Rim Exit 1 Strike Mounting Plate OT Strike Gate Hardware by Gate Gate mounting Hardware by Gate 1 OT Manufacturer Manufacturer

Notes: Operation: • The Gate normally closed and secure. • When there is an authorized card read on the secured side of the gate, the exit device latch will retract to allow entry. • Manual egress is always available by pushing on the exit device push bar. Request to Exit Switch will allow authorized egress without alarm. • Exit device is fail secure and will remain latched in the event of a fire alarm or power outage.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Door Hardware IFB 21-06-406 Section 08 71 00 - Page 32 of 32

END OF SECTION 080671

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Security Glazing IFB 21-06-406 Section 08 88 53 - Page 1 of 5

SECTION 08 88 53 - SECURITY GLAZING

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Safety and security glazing for doors, windows, and aluminum framed storefront.

1.2 RELATED SECTIONS

A. Division 08 - Openings.

B. Section 08 80 00 - Glazing.

1.3 REFERENCES

A. ASTM International (ASTM): 1. ASTM C509 - Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material. 2. ASTM C864 - Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers. 3. ASTM D635 - Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position. 4. ASTM D638 - Standard Test Method for Tensile Properties of Plastics. 5. ASTM D790 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials. 6. ASTM D1003 - Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics. 7. ASTM D1929 - Standard Test Method for Determining Ignition Temperature of Plastics. 8. ASTM E283 - Standard Test Method for Rate and Air Leakage Through Exterior Windows, Curtain Walls, and Doors. 9. ASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Door by Uniform Static Air Pressure Difference. 10. ASTM F1233 - Standard Test Method for Security Glazing Materials and Systems.

B. American Architectural Manufacturers Association (AAMA): 1. AAMA/NWWDA 101/I.S.2 - Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors. 2. AAMA 611 - Voluntary Specification for Anodized Architectural Aluminum"

C. American National Standards Institute (ANSI): 1. ANSI Z97.1 - Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Test.

D. Consumer Products Safety Council (CPSC): 1. CPSC 16 CRF 1201 - Safety Standards for Glazing Materials.

E. H.P. White Laboratory, Inc. (HPW): 1. HPW-TP-0500.03 - Test Procedure for Transparent Materials for Use in Forced Entry or Containment Barriers.

F. ICC Evaluation Services (ICC-ES): 1. ICC-ES Evaluation Report ESR-2728.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Security Glazing IFB 21-06-406 Section 08 88 53 - Page 2 of 5

G. US Department of Defense (DoD): 1. DoD, Unified Facilities Criteria (UFC) 4-010-01 - DoD Minimum Antiterrorism Standards.

H. US Department of Justice, National Institute of Justice (NIJ): 1. NIJ 0108.01 - Ballistic Resistant Protective Materials.

I. US State Department: 1. SD-STD-01.01 - Certification Standard - Forced entry and Ballistic Resistance or Structural Systems.

J. Underwriters Laboratories (UL): 1. UL 752 - Bullet Resisting Equipment. 2. UL 94 - Flammability. 3. UL 972 - Burglary Resisting Glazing Material. 4. UL 746C - Suitability for Outdoor Use.

1.4 SUBMITTALS

A. Submit under provisions of Section 01 30 00.

B. Product Data: 1. Manufacturer's data sheets on each product to be used. 2. Preparation instructions and recommendations. 3. Storage and handling requirements and recommendations. 4. Typical installation methods.

C. Shop Drawings: Include details of materials, construction, and finish. Include relationship with adjacent construction.

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with a minimum five years documented experience.

B. Installer Qualifications: Company certified by Impact Security, LLC for installation of DefenseLite Products.

C. Source Limitations: Provide each type of product from a single manufacturing source to ensure uniformity.

1.6 PRE-INSTALLATION CONFERENCE

A. Convene a conference approximately two weeks before scheduled commencement of the Work. Attendees shall include Architect, Contractor and trades involved. Agenda shall include schedule, responsibilities, critical path items and approvals.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Store and handle in strict compliance with manufacturer's written instructions and recommendations.

B. Protect from damage due to weather, excessive temperature, and construction operations.

1.8 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Security Glazing IFB 21-06-406 Section 08 88 53 - Page 3 of 5

environmental conditions outside manufacturer's recommended limits.

1.9 WARRANTY

A. Manufacturer's Warranty: Manufacturer's two (2) year standard limited warranty for parts and labor when installed by manufacturer certified installer. 1. Polycarbonate Shield Warranty: Seven (7) years.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Basis of Design: Impact Security LLC, which is located at: 600 Kirk Rd. Suite 100; Marietta, GA 30060; ASD Toll Free Tel: 888-689-5502; Fax: 678-547-3138; Email: [email protected]; Web: https://www.defenselite.com

B. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00.

2.2 PERFORMANCE REQUIREMENTS

A. Ballistics-Resistance Performance: Provide units identical to those tested for compliance with the following requirements: 1. Listed and labeled as bullet resisting according to UL 752. 2. Tested for ballistics resistance according to UL 752, ASTM F1233, HPW-TP-0500.03, or NIJ STD-0108.01, by a testing agency acceptable to authorities that have jurisdiction. 3. Certified as complying with SD-STD-01.01, by US State Department, for ballistics resistance when tested by a qualified testing agency.

B. Air Infiltration for Fixed Windows: Not more than 0.010 cfm/ft. (0.015 L/s per m) of crack length at an inward test pressure of 1.56 lbs/sq ft (75 Pa) when tested according to ASTM E283.

C. Water Penetration: No water penetration as defined in test method at an inward test pressure of 1.56 lbf/sq ft (75 Pa) when tested according to ASTM E331.

2.3 SAFETY AND SECURITY GLAZING SYSTEMS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. Basis of Design Product: Subject to compliance with requirements, provide BulletShield as manufactured by Impact Security, LLC or comparable product by one of the following a. Creative Industries, Inc. 1) Custom Bullet Resistant Solutions b. Riot Glass™ c. Saftifirst™ Ballistic Fire Resistive Doors and Window

B. Performance Requirements: 1. Ballistic Level (UL 752): Level 3. 2. Description: Polished surface, UV stabilized, transparent security shield. 3. Patented, professionally installed system. 4. Glazing: UL listed multi-ply polycarbonate. 5. Glazing Thickness: To be determined based on shielding and security requirements. 6. Glazing Sheet Size: As indicated on the Drawings.

2.4 FABRlCATlON

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Security Glazing IFB 21-06-406 Section 08 88 53 - Page 4 of 5

A. Shields and Hardware: 1. Fabricate security and ballistic shields from pre-determined sheet sizes as manufactured. 2. Cut and fabricate security panels and mounting hardware to surveyed sizes.

B. Finish work neat and free from defects.

C. Tolerances: Plus, or minus 1/16 inch (1.6 mm) for frame opening width, height, diagonal dimensions, and overall width and height, outside to outside.

2.5 MATERIALS

A. Extruded Aluminum: ASTM B221, 6063 alloy.

B. Neoprene Glazing Gaskets: 1. Interior Glazing gaskets closed cell cellular neoprene conforming to ASTM C509 Type II Option 1 with a 40-50 Shore A Durometer. 2. Exterior Glazing gaskets solid neoprene conforming to ASTM C864 with a 65-75 Shore A Durometer.

C. Weatherstripping: Entrance manufacturer's standard types to suit application.

D. Fasteners: Stainless steel or corrosion resistant steel.

E. Glazing Sealants and Adhesives: 1. Dow 995 or Dow 795 for exterior applications. 2. Dow 995, Dow 795, or 3M IPA for interior applications.

2.6 ACCESSORY COMPONENTS

A. Edge Banding: Available in various colors to make system virtually invisible.

B. Aluminum Standoffs: Designed to keep protected glass from breaking.

C. Bottom Frame: Eliminates moisture to prevent fogging.

D. DefenseLite Super Bond: Secures the system.

2.7 FlNlSHES

A. Aluminum Finishes: 1. Powder Coat Finish: Manufacturer's standard polyester powder coat, sprayed and baked: a. PPG Duranar with resin containing 70 percent fluoropolymer; thermosetting; alternative finishes will not be acceptable, conforming to AAMA 2605. b. Pretreatment: Five-stage; zinc chromate conversion coating. c. Application: Electrostatic spray and oven bake by approved applicator. d. Coating quantity: Minimum one primer coat and one color coat. e. Dry film thickness: Minimum 1.2 mils (0.03 mm) on exposed surfaces, except inside corners and channels. f. Color: Match existing frame color.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly constructed and prepared.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Security Glazing IFB 21-06-406 Section 08 88 53 - Page 5 of 5

B. If substrate preparation is the responsibility of another installer, notify Architect in writing of unsatisfactory preparation before proceeding.

3.2 PREPARATION

A. Clean surfaces thoroughly prior to installation.

B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions, approved submittals, and in proper relationship with adjacent construction.

B. Install plumb, level, square, true to line, and without warp or rack.

C. Provide all fasteners required for installation.

D. Anchor frames securely in place to supports. Use attachment methods permitting adjustment for construction tolerances, irregularities, alignment, and expansion and contraction.

E. Joint Sealants: Install joint sealants as specified in Section 07 21 19.

F. Adjust door equipment for correct function and smooth operation. Verify water and weather tight installation as applicable.

3.4 FIELD QUALITY CONTROL

A. Field Inspection: Coordinate field inspection in accordance with appropriate sections in Division 01.

B. Manufacturer's Services: Coordinate manufacturer's services in accordance with appropriate sections in Division 01.

3.5 CLEANING AND PROTECTION

A. Clean products in accordance with the manufacturer's recommendations.

B. Remove excess joint sealant in accordance with sealant manufacturer's instructions.

C. Do not use harsh cleaning materials or methods that would damage glazing or finish.

D. Protect installed products until completion of project.

E. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

ETICA GROUP Etica Group Project # 200061.04 This page intentionally left blank. Mobility Solutions & Customer Care Center Exterior Painting IFB 21-06-406 Section 09 91 13 - Page 1 of 5

SECTION 09 91 13 - EXTERIOR PAINTING

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Concrete masonry units (CMUs).

B. Related Requirements:

1. Section 05 12 00 "Structural Steel Framing" for shop priming of metal substrates. 2. Section 05 50 00 "Metal Fabrications" for shop priming metal fabrications.

1.3 DEFINITIONS

A. MPI Gloss Level 1: Not more than five units at 60 degrees and 10 units at 85 degrees, according to ASTM D 523.

B. MPI Gloss Level 3: 10 to 25 units at 60 degrees and 10 to 35 units at 85 degrees, according to ASTM D 523.

C. MPI Gloss Level 4: 20 to 35 units at 60 degrees and not less than 35 units at 85 degrees, according to ASTM D 523.

D. MPI Gloss Level 5: 35 to 70 units at 60 degrees, according to ASTM D 523.

E. MPI Gloss Level 6: 70 to 85 units at 60 degrees, according to ASTM D 523.

F. MPI Gloss Level 7: More than 85 units at 60 degrees, according to ASTM D 523.

1.4 ACTION SUBMITTALS

A. Product Data: For each type of product. Include preparation requirements and application instructions.

1. Include printout of current "MPI Approved Products List" for each product category specified, with the proposed product highlighted. 2. Indicate VOC content.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Exterior Painting IFB 21-06-406 Section 09 91 13 - Page 2 of 5

B. Samples for Verification: For each type of paint system and each color and gloss of topcoat.

1. Submit Samples on rigid backing, 8 inches (200 mm) square. 2. Apply coats on Samples in steps to show each coat required for system. 3. Label each coat of each Sample. 4. Label each Sample for location and application area.

C. Product List: Cross-reference to paint system and locations of application areas. Use same designations indicated on Drawings and in schedules. Include color designations.

1.5 MAINTENANCE MATERIAL SUBMITTALS

A. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.

1.6 QUALITY ASSURANCE

A. Mockups: Apply mockups of each paint system indicated and each color and finish selected to verify preliminary selections made under Sample submittals and to demonstrate aesthetic effects and set quality standards for materials and execution.

1. Architect will select one surface to represent surfaces and conditions for application of each paint system.

a. Vertical and Horizontal Surfaces: Provide samples of at least 100 sq. ft. (9 sq. m). b. Other Items: Architect will designate items or areas required.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Store materials not in use in tightly covered containers in well-ventilated areas with ambient temperatures continuously maintained at not less than 45 deg F (7 deg C).

1. Maintain containers in clean condition, free of foreign materials and residue. 2. Remove rags and waste from storage areas daily.

1.8 FIELD CONDITIONS

A. Apply paints only when temperature of surfaces to be painted and ambient air temperatures are between 50 and 95 deg F (10 and 35 deg C).

B. Do not apply paints in snow, rain, fog, or mist; when relative humidity exceeds 85 percent; at temperatures less than 5 deg F (3 deg C) above the dew point; or to damp or wet surfaces.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Exterior Painting IFB 21-06-406 Section 09 91 13 - Page 3 of 5

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Approved Manufacturers: 1. Benjamin Moore & Co. 2. PPG Paints 3. Sherwin-Williams Company

2.2 PAINT, GENERAL

A. MPI Standards: Products shall comply with MPI standards indicated and shall be listed in its "MPI Approved Products Lists."

B. Material Compatibility:

1. Materials for use within each paint system shall be compatible with one another and substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience. 2. For each coat in a paint system, products shall be recommended in writing by topcoat manufacturers for use in paint system and on substrate indicated.

C. Colors: As selected by Architect from manufacturer's full range

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates and conditions, with Applicator present, for compliance with requirements for maximum moisture content and other conditions affecting performance of the Work.

B. Maximum Moisture Content of Substrates: When measured with an electronic moisture meter as follows: 1. Masonry (Clay and CMUs): 12 percent.

C. Verify suitability of substrates, including surface conditions and compatibility, with existing finishes and primers.

D. Proceed with coating application only after unsatisfactory conditions have been corrected.

1. Application of coating indicates acceptance of surfaces and conditions.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Exterior Painting IFB 21-06-406 Section 09 91 13 - Page 4 of 5

3.2 PREPARATION

A. Clean substrates of substances that could impair bond of paints, including dust, dirt, oil, grease, and incompatible paints and encapsulants.

1. Remove incompatible primers and reprime substrate with compatible primers or apply tie coat as required to produce paint systems indicated.

B. Concrete Substrates: Remove release agents, curing compounds, efflorescence, and chalk. Do not paint surfaces if moisture content or alkalinity of surfaces to be painted exceeds that permitted in manufacturer's written instructions.

C. Masonry Substrates: Remove efflorescence and chalk. Do not paint surfaces if moisture content or alkalinity of surfaces or mortar joints exceeds that permitted in manufacturer's written instructions.

D. Shop-Primed Steel Substrates: Clean field welds, bolted connections, and areas where shop paint is abraded. Paint exposed areas with the same material as used for shop priming to comply with SSPC-PA 1 for touching up shop-primed surfaces.

E. Galvanized-Metal Substrates: Remove grease and oil residue from galvanized sheet metal by mechanical methods to produce clean, lightly etched surfaces that promote adhesion of subsequently applied paints.

3.3 APPLICATION

A. Apply paints according to manufacturer's written instructions and recommendations in "MPI Architectural Painting Specification Manual."

1. Use applicators and techniques suited for paint and substrate indicated. 2. Paint surfaces behind movable items same as similar exposed surfaces. Before final installation, paint surfaces behind permanently fixed items with prime coat only. 3. Paint both sides and edges of exterior doors and entire exposed surface of exterior door frames. 4. Do not paint over labels of independent testing agencies or equipment name, identification, performance rating, or nomenclature plates. 5. Primers specified in painting schedules may be omitted on items that are factory primed or factory finished if acceptable to topcoat manufacturers.

B. If undercoats or other conditions show through topcoat, apply additional coats until cured film has a uniform paint finish, color, and appearance.

C. Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks, roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color breaks.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center Exterior Painting IFB 21-06-406 Section 09 91 13 - Page 5 of 5

3.4 FIELD QUALITY CONTROL

A. Dry Film Thickness Testing: Owner may engage the services of a qualified testing and inspecting agency to inspect and test paint for dry film thickness.

1. Contractor shall touch up and restore painted surfaces damaged by testing. 2. If test results show that dry film thickness of applied paint does not comply with paint manufacturer's written recommendations, Contractor shall pay for testing and apply additional coats as needed to provide dry film thickness that complies with paint manufacturer's written recommendations.

3.5 CLEANING AND PROTECTION

A. At end of each workday, remove rubbish, empty cans, rags, and other discarded materials from Project site.

B. After completing paint application, clean spattered surfaces. Remove spattered paints by washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces.

C. Protect work of other trades against damage from paint application. Correct damage to work of other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, and leave in an undamaged condition.

D. At completion of construction activities of other trades, touch up and restore damaged or defaced painted surfaces.

3.6 EXTERIOR PAINTING SCHEDULE

A. CMU Substrates:

1. Water-Based Light Industrial Coating System MPI EXT 4.2C:

a. Prime Coat: Block filler, latex, interior/exterior, MPI #4.

END OF SECTION 09 91 13

ETICA GROUP Etica Group Project # 200061.04 This page intentionally left blank.

Mobility Solutions & Customer Care Center LIGHTING CONTROL DEVICES IFB 21-06-406 Section 260923 - Page 1

SECTION 260923 - LIGHTING CONTROL DEVICES

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Indoor occupancy and vacancy sensors. 2. Switchbox-mounted occupancy sensors. 3. High-bay occupancy sensors. 4. Digital timer light switch. 5. Lighting contactors.

1.2 SUBMITTALS

A. Product Data: For each type of product.

B. Shop Drawings: Show installation details for occupancy and light-level sensors.

1. Interconnection diagrams showing field-installed wiring. 2. Include diagrams for power, signal, and control wiring. 3. Provide factory certified occupancy sensor and light-level senor coverage layout drawing.

C. Operation and Maintenance Data: For each type of lighting control device to include in emergency, operation, and maintenance manuals.

1.3 CLOSEOUT SUBMITTALS

A. Operation and Maintenance Data: For each type of lighting control device to include in operation and maintenance manuals.

PART 2 - PRODUCTS

2.1 OUTDOOR PHOTOELECTRIC SWITCHES

A. Description: Solid state, with SPST dry contacts rated for 1000 W incandescent or 1800 VA inductive, to operate connected relay, contactor coils, or microprocessor input; complying with UL 773A, and compatible with ballasts and LED lamps. 1. Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

APPLIED ENGINEERING Applied Engineering Project No. 21-026

Mobility Solutions & Customer Care Center LIGHTING CONTROL DEVICES IFB 21-06-406 Section 260923 - Page 2

2. Light-Level Monitoring Range: 1.5 to 10 fc (16.14 to 108 lux), with an adjustment for turn-on and turn-off levels within that range, and a directional lens in front of the photocell to prevent fixed light sources from causing turn-off. 3. Time Delay: Fifteen-second minimum, to prevent false operation. 4. Surge Protection: Metal-oxide varistor. 5. Mounting: Twist lock complies with NEMA C136.10, with base-and-stem mounting or stem-and-swivel mounting accessories as required to direct sensor to the north sky exposure. 6. Failure Mode: Luminaire stays ON.

2.2 INDOOR OCCUPANCY AND VACANCY SENSORS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Cooper Industries, Inc. 2. Hubbell Building Automation, Inc. 3. Lithonia Lighting; Acuity Brands Lighting, Inc. 4. Watt Stopper.

B. General Requirements for Sensors: Wall- or ceiling-mounted, solid-state indoor occupancy sensors with a separate power pack and/or line voltage type.

1. Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. 2. Operation: Manual on, Auto off - Unless otherwise indicated, occupant turns lights on when enter the room via switch and/or button, and turn them off when unoccupied or person operate a switch and/or button; with a time delay for turning lights off, adjustable over a minimum range of 1 to 30 minutes. 3. Sensor Output: Contacts rated to operate the connected relay or load, complying with UL 773A. Sensor is powered from the power pack or line voltage. 4. Power Pack: Dry contacts rated for 20-A ballast load at 120- and 277-V ac, for 13-A tungsten at 120-V ac, and for 1 hp at 120-V ac. Sensor has 24-V dc, 150- mA, Class 2 power source, as defined by NFPA 70. 5. Mounting:

a. Sensor: Suitable for mounting in any position on a standard outlet box. b. Power pack: Externally mounted through a 1/2-inch knockout in a standard electrical enclosure. c. Time-Delay and Sensitivity Adjustments: Recessed and concealed behind hinged door.

6. Indicator: Digital display, to show when motion is detected during testing and normal operation of sensor. 7. Bypass Switch: Override the "on" function in case of sensor failure. 8. Automatic Light-Level Sensor: Adjustable from 2 to 200 fc; turn lights off when selected lighting level is present. 9. Adaptive Technology: Self-adjusting circuitry detects and memorizes usage patterns of space/area and help eliminate false “off switching”.

APPLIED ENGINEERING Applied Engineering Project No. 21-026

Mobility Solutions & Customer Care Center LIGHTING CONTROL DEVICES IFB 21-06-406 Section 260923 - Page 3

C. Dual-Technology Type: Ceiling mounted; detect occupants in coverage area using PIR and ultrasonic or microphonics detection methods. The particular technology or combination of technologies that control on-off functions is selectable in the field by operating controls on unit.

1. Sensitivity Adjustment: Separate for each sensing technology. 2. Detector Sensitivity: Detect occurrences of 6-inch-minimum movement of any portion of a human body that presents a target of not less than 36 sq. in., and detect a person of average size and weight moving not less than 12 inches in either a horizontal or a vertical manner at an approximate speed of 12 inches/s. 3. Detection Coverage (Standard Room): Detect occupancy anywhere within a circular area of 1000 sq. ft. when mounted on a 96-inch-high ceiling. 4. Detection Coverage (Large Room): Detect occupancy anywhere within a circular area of 2000 sq. ft. (186 sq. m) when mounted on a 96-inch- (2440-mm-) high ceiling. 5. Detection Coverage (Corridor): Detect occupancy anywhere within 90 feet (27.4 m) when mounted on a 10-foot- (3-m-) high ceiling in a corridor not wider than 14 feet (4.3 m).

2.3 SWITCHBOX-MOUNTED OCCUPANCY SENSORS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Cooper Industries, Inc. 2. Hubbell Building Automation, Inc. 3. Lithonia Lighting; Acuity Brands Lighting, Inc. 4. Watt Stopper.

B. General Requirements for Sensors: Automatic-wall-switch occupancy sensor, suitable for mounting in a single gang switchbox.

1. Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. 2. Operating Ambient Conditions: Dry interior conditions, 32 to 120 deg F. 3. Switch Rating: Not less than 800-VA fluorescent/LED at 120 V, 1200-VA fluorescent/LED at 277 V. 4. Operation: Unless otherwise indicated, turn lights on when coverage area is occupied, and turn them off when unoccupied; with a time delay for turning lights off, adjustable over a minimum range of 1 to 30 minutes. 5. Operation: Unless otherwise indicated, turn lights on when person pushes a button, and turn them off when person pushes a button or when unoccupied, with a time delay for turning lights off, adjustable over a minimum range of 1 to 30 minutes.

C. Wall-Switch Sensor:

APPLIED ENGINEERING Applied Engineering Project No. 21-026

Mobility Solutions & Customer Care Center LIGHTING CONTROL DEVICES IFB 21-06-406 Section 260923 - Page 4

1. Standard Range: 180-degree field of view, field adjustable from 180 to 40 degrees; with a minimum coverage area of 900 sq. ft. . 2. Sensing Technology: Dual technology - PIR and ultrasonic/microphonics. 3. Switch Type: Field selectable automatic "on," or manual "on" automatic "off or manual off." 4. Voltage: Dual voltage, 120 and 277 V; dual-technology type. 5. Ambient-Light Override: Concealed, field-adjustable, light-level sensor from 10 to 150 fc. The switch prevents the lights from turning on when the light level is higher than the set point of the sensor. 6. Concealed, field-adjustable, "off" time-delay selector at up to 30 minutes. 7. Adaptive Technology: Self-adjusting circuitry detects and memorizes usage patterns of the space and helps eliminate false "off" switching.

2.4 HIGH-BAY OCCUPANCY SENSORS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Cooper Industries, Inc. 2. Hubbell Building Automation, Inc. 3. Lithonia Lighting; Acuity Brands Lighting, Inc. 4. Watt Stopper.

B. General Description: Solid-state unit. The unit is designed to operate with the lamp and ballasts indicated.

1. Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. 2. Operation: Turn lights on when coverage area is occupied, and lights off when unoccupied; with a time delay for turning lights to half-power that is adjustable over a minimum range of 1 to 16 minutes. 3. Power: Line voltage. 4. Operating Ambient Conditions: 32 to 149 deg F (0 to 65 deg C). 5. Mounting: Threaded pipe. 6. Time-Delay and Sensitivity Adjustments: Recessed and concealed behind hinged door. 7. Detector Technology: PIR.

C. Detector Coverage: User selectable by interchangeable PIR lenses, suitable for mounting heights from 12 to 50 feet (3.7 to 15.2 m).

D. Accessories: Obtain manufacturer's installation and maintenance kit with laser alignment tool for sensor positioning and power port connectors.

2.5 DIGITAL TIMER LIGHT SWITCH

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

APPLIED ENGINEERING Applied Engineering Project No. 21-026

Mobility Solutions & Customer Care Center LIGHTING CONTROL DEVICES IFB 21-06-406 Section 260923 - Page 5

1. Legrand Wattstopper #RT-200 (Basis of Design) 2. Cooper Industries, Inc. 3. Intermatic, Inc. 4. Leviton Manufacturing Co., Inc. 5. NSi Industries LLC.

B. Description: Combination digital timer, conventional switch lighting control unit, and astronomical switch for scheduled control. Switchbox-mounted, backlit LCD display.

1. Rated 800 W at 120-V ac and 1/6 horsepower at 120-V ac. 2. Integral relay for connection to BAS. 3. Color: Match wiring devices. 4. Faceplate: Color matched to switch.

2.6 LIGHTING CONTACTORS

A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to the following:

1. ASCO 2. ABB 3. Square D 4. Eaton

B. Description: Electrically operated and electrically held, combination-type lighting contactors with nonfused disconnect, complying with NEMA ICS 2 and UL 508.

1. Current Rating for Switching: Listing or rating consistent with type of load served, including tungsten filament, inductive, and high-inrush ballast (ballast with 15 percent or less THD of normal load current). 2. Fault Current Withstand Rating: Equal to or exceeding the available fault current at the point of installation. 3. Enclosure: Comply with NEMA 250. 4. Provide with control switch devices as indicated on Drawings, matching the NEMA type specified for the enclosure.

2.7 CONDUCTORS AND CABLES

A. Power Wiring to Supply Side of Remote-Control Power Sources: Not smaller than No. 12 AWG. Comply with requirements in Division 26 "Low-Voltage Electrical Power Conductors and Cables."

B. Classes 2 and 3 Control Cable: Multiconductor cable with stranded-copper conductors not smaller than No. 18 AWG. Comply with requirements in Division26 "Low-Voltage Electrical Power Conductors and Cables."

APPLIED ENGINEERING Applied Engineering Project No. 21-026

Mobility Solutions & Customer Care Center LIGHTING CONTROL DEVICES IFB 21-06-406 Section 260923 - Page 6

C. Class 1 Control Cable: Multiconductor cable with stranded-copper conductors not smaller than No. 14 AWG. Comply with requirements in Division 26 "Low-Voltage Electrical Power Conductors and Cables."

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine lighting control devices before installation. Reject lighting control devices that are wet, moisture damaged, or mold damaged.

B. Examine walls and ceilings for suitable conditions where lighting control devices will be installed.

C. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 SENSOR INSTALLATION

A. Comply with NECA 1.

B. Coordinate layout and installation of ceiling-mounted devices with other construction that penetrates ceilings or is supported by them, including light fixtures, HVAC equipment, smoke detectors, fire-suppression systems, and partition assemblies.

C. Install and aim sensors in locations to achieve not less than 90 percent coverage of areas indicated. Do not exceed coverage limits specified in manufacturer's written instructions.

3.3 CONTACTOR INSTALLATION

A. Comply with NECA 1.

B. Mount electrically held lighting contactors with elastomeric isolator pads to eliminate structure-borne vibration unless contactors are installed in an enclosure with factory- installed vibration isolators.

3.4 WIRING INSTALLATION

A. Comply with NECA 1.

B. Wiring Method: Comply with Division 26 "Low-Voltage Electrical Power Conductors and Cables." Minimum conduit size is 3/4 inch.

C. Wiring within Enclosures: Comply with NECA 1. Separate power-limited and nonpower- limited conductors according to conductor manufacturer's written instructions.

APPLIED ENGINEERING Applied Engineering Project No. 21-026

Mobility Solutions & Customer Care Center LIGHTING CONTROL DEVICES IFB 21-06-406 Section 260923 - Page 7

D. Size conductors according to lighting control device manufacturer's written instructions unless otherwise indicated.

E. Splices, Taps, and Terminations: Make connections only on numbered terminal strips in junction, pull, and outlet boxes; terminal cabinets; and equipment enclosures.

3.5 IDENTIFICATION

A. Identify components and power and control wiring according to Division 26 "Identification for Electrical Systems."

1. Identify controlled circuits in lighting contactors. 2. Identify circuits or luminaires controlled by photoelectric and occupancy sensors at each sensor.

B. Label time switches and contactors with a unique designation.

3.6 FIELD QUALITY CONTROL

A. Perform the following tests and inspections with the assistance of a factory-authorized service representative:

1. Operational Test: After installing time switches and sensors, and after electrical circuitry has been energized, start units to confirm proper unit operation. 2. Test and adjust controls and safeties. Replace damaged and malfunctioning controls and equipment.

B. Lighting control devices will be considered defective if they do not pass tests and inspections.

C. Prepare test and inspection reports.

3.7 DEMONSTRATION

A. Coordinate demonstration of products specified in this Section with demonstration requirements for low-voltage, programmable lighting control systems specified in Division 26.

B. Train Owner's maintenance personnel to adjust, operate, and maintain lighting control devices.

END OF SECTION 260923

APPLIED ENGINEERING Applied Engineering Project No. 21-026

Mobility Solutions & Customer Care Center DECORATIVE METAL FENCES AND GATES IFB 21-06-406 Section 32 31 00 - Page 1 of 5

SECTION 32 31 00 - DECORATIVE METAL FENCES AND GATES

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Ornamental rackable welded steel fence

B. Ornamental Swing Gates

1.2 RELATED SECTIONS

A. Section 03 30 00 - Cast-in-Place Concrete.

1.3 REFERENCES

A. American Society for Testing and Materials International (ASTM). 1. ASTM A653 - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process. 2. ASTM D523 - Standard Test Method for Specular Gloss. 3. ASTM D714 - Standard Test Method for Evaluating Degree of Blistering of Paints. 4. ASTM D822 - Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings. 5. ASTM D2244 - Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates. 6. ASTM D3359 - Standard Test Methods for Measuring Adhesion by Tape Test. 7. ASTM F2408 - Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets.

B. American Welding Society (AWS): AWS D1.1 - Structural Welding Code - Steel

1.4 SUBMITTALS

A. Submit under provisions of Section 01 33 00 – Submittal Procedures.

B. Manufacturer's printed product information indicating material compliance and specified options are to be submitted prior to installation. Submit manufacturer's product data sheets on each product to be used.

C. Shop drawings shall include plans, elevations, sections, details, and attachments to other work. Drawings must be submitted for approval and be approved prior to installation.

D. Design data which verifies compliance with design loads specified in Performance Requirements Article. Design data shall be signed and sealed by the qualified professional engineer responsible for their preparation.

E. Submit samples for initial color selection. Submit samples of each specified finish.

1.5 QUALITY ASSURANCE

A. Manufacturing company with engineering and fabrication of custom fencing and gate systems for a minimum of 15 years.

B. Installation company with experienced in manufacturer's products for a minimum of 5 years. The Contractor shall provide trained laborers with prior experience in the type of construction involved as well as experience installing the materials and techniques specified.

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center DECORATIVE METAL FENCES AND GATES IFB 21-06-406 Section 32 31 00 - Page 2 of 5

C. Obtain each fence system and gates through one source from a single manufacturer.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Upon delivery to the jobsite, inspect all materials for damage that might have occurred during shipment.

B. Handle and store materials in manufacturer's packaging until materials are ready to be installed. Store materials in such a way as to prevent damage and theft.

1.7 PROJECT CONDITIONS

A. Verify actual locations of walls and other construction contiguous with fencing and gates by field measurements before fabrication and indicate measurements on shop drawings. Provide allowance for trimming and fitting onsite.

1.8 COORDINATION AND SCHEDULING

A. Coordinate installation of anchorages for fencing and gates. Furnish setting drawings, templates, and directions for installing anchorages, including sleeves, concrete inserts, anchor bolts, and items with integral anchors that are to be embedded in concrete or masonry. Deliver such items to the Project Site in time for installation.

B. Schedule installation so wall attachments are made only to completed walls. Do not support systems temporarily by any means that do not satisfy structural performance requirements.

1.9 WARRANTY

A. Manufacturer's Warranty: Provide manufacturer's standard 20 year limited warranty, from the date of purchase, against defects in materials and workmanship including protection against cracking, peeling, blistering, and corrosion (rusting).

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Basis of Design Manufacturer: Fortress Fence Products, which is located at: 1720 N. First St.; Garland, TX 75040; Toll Free Tel: 844-909-1999; Fax: 972-372-0078; Email:request info ([email protected]); Web:http://www.fortressfence.com 1. Versai V2 Commercial Ornamental Fencing

B. Acceptable Manufacturers and Products: 1. Iron World Manufacturing, LLC; Maverick™ Commercial; Aberdeen 2. Ameristar Perimeter Security; Montage Commercial 3-Rail Majestic

C. Substitutions: Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements, as well as Section 01 25 00 – Substitution Procedures.

2.2 SITE FENCING AND GATES

A. Minimum Post Sizes: 1. Line of Fence Posts: 2.5” x 14 ga

B. Panel Heights: 7’-0” & 8’-0”

C. Commercial Post Spacing 1. Style Flat Top

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center DECORATIVE METAL FENCES AND GATES IFB 21-06-406 Section 32 31 00 - Page 3 of 5

2. Spacing per drawing

D. Commercial Gate Posts Sizes:

Gate Leaf Gate Height

Up to & Including 4' Over 4' Up to & Including 7' & 8' 6'

Up to 4' 2.5" x 14ga 3" x 12ga 3" x 12ga

4'1" to 6' 3" x 12ga 3" x 12ga 4" x 11ga

6'1" to 8' 3" x 12ga 4" x 11ga 4" x 11ga

E. Ornamental Rackable Welded Steel Fence Systems: 1. Basis of Design: Versai Commercial (V2) Fence Systems as manufactured by Fortress Fence Products, a division of The Fortress Company. a. Style: Flat Top, Extended Bottom (FT). b. Rails: 3. c. Color: Black d. Fence Panels: Fabricated in standard length of 90-1/2 inches (2299 mm). 1) Height: 94 inch (2386 mm). e. Airspace Between Pickets: 3-15/16 inch. f. Materials: 1) Rails shall be cold-rolled steel formed U-channel and pickets shall be cold-rolled steel formed and welded tubing, both having a Grade A minimum tensile strength of 45,000 psi (310 MPa) conforming to ASTM A653 and have a G60 zinc coating, 0.60 oz./ft2 (0.18 kg/m2) in accordance with ASTM A653. 2) Posts shall be cold-rolled steel formed and welded tubing with a Grade A minimum tensile strength of 45,000 psi (310 MPa) conforming to ASTM A653, have a G60 zinc coating, 0.60 oz./ft2 (0.18 kg/m2) in accordance with ASTM A653, and have a powder-coated factory finish. g. Components: 1) Rails: 1-9/16 inch (40 mm) by 1-3/16 inch (30 mm) (Leg x Web), 14 gauge. 2) Pickets: a) 3/4 inch (19 mm) square, 14 gauge. h. Posts: 2-1/2 inch (64 mm) square, 16 gauge. i. Gates: Provide manufacturer's standard gates and hardware. j. Fence panels shall be fabricated in standard length of 90-1/2 inches (2299 mm). Comply with requirements indicated for materials, thickness, design, and details of construction. k. Pickets are welded to the rails with a patented pin hinge system which allows the panel to rake without metal fatigue or damage to the finish. l. Welded connections shall comply with AWS standards for recommended practice in shop welding. m. Components shall be accurately cut and drilled to receive hardware, fasteners, and accessories. n. Panels shall be rackable to an 18 degree change in grade (30 inch vertical travel per panel). o. Fence panel shall be capable of meeting structural test load capabilities for a commercial fence system referenced in table 2 of ASTM 2409. p. Fence panel shall be capable of meeting coating performance requirements in

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center DECORATIVE METAL FENCES AND GATES IFB 21-06-406 Section 32 31 00 - Page 4 of 5

table 3 of ASTM 2409. 2. Finish: a. Materials are coated with a finish that includes galvanization, zinc phosphate, electrodeposition (E-coat), and architectural grade powder coat. b. Metal parts shall be assembled and finished individually prior to shipment. c. Galvanized steel fence components shall be cleaned with a non-petroleum solvent followed by the application of a sealing zinc phosphate coating. d. Immediately after sealing, provide a two-step finishing process consisting first of an electrostatic dipping process in a lead-free high corrosion resistant epoxy resin leaving a coating of approximately 20 microns followed by a thermosetting carboxyl polyester resin top coat with a minimum dry film thickness of 60 microns. The second coating shall be applied by the electrostatic spray process.

PART 3 EXECUTION

3.1 EXAMINATION

A. Examine areas and conditions under which the work is to be installed, and notify the Contractor in writing, with a copy to the Owner and the Architect, of any conditions detrimental to the proper and timely completion of the work. Do not proceed with the work until unsatisfactory conditions have been corrected.

3.2 PREPARATION

A. Stake layout showing locations of gates and posts per submitted shop drawings.

B. Contact applicable authorities and take necessary precautions prior to beginning any excavation work.

3.3 INSTALLATION

A. Install fences in accordance with manufacturer's written instructions and in accordance with authorities having jurisdiction. Installation shall conform to the specifications referenced elsewhere in this Section and as indicated on the Drawings.

B. Refer to Division 3 for concrete specification. Recommend minimum 28 day compressive strength of 3,000 psi (20 MPa). Crown concrete at top to shed water.

C. On-center post spacing per manufacturer's drawings.

D. Install brackets onto fence section and posts as indicated in manufacturer's printed instructions for specific fence style. Attach fence sections to brackets with approved fasteners and techniques.

E. Install gate in accordance with manufacturer's printed instructions and approved signoff drawings. Do not mount gate from wall of a structure. Provide gate post on both sides of a gate. For double drive gate installation, provide concrete center drop to foundation depth and drop rod retainers at center. Lubricate to ensure smooth operation and verify proper latch operation.

F. Attach all hardware to gate in such a way that it cannot be removed by unauthorized persons.

G. Attach latch and make sure that gate is received by latch in a secure manner.

3.4 ERECTION TOLERANCES

ETICA GROUP Etica Group Project # 200061.04 Mobility Solutions & Customer Care Center DECORATIVE METAL FENCES AND GATES IFB 21-06-406 Section 32 31 00 - Page 5 of 5

A. Maximum Variation from Plumb: ¼ inch.

B. Maximum Offset from Indicated Position: 1 inch.

C. Minimum distance from property line: 6 inches.

3.5 CLEANING

A. Remove cutting and drilling chips that are attached to the fencing, post, brackets, or additions to prevent corrosion.

B. Repair scratches and other installation-incurred damage using manufacturers recommended paint. Use paint of the appropriate color with a zinc additive to prevent rust from forming.

C. Clean up debris and unused material, and remove from site.

3.6 PROTECTION

A. Protect finishes from damage during construction period with temporary protective coverings approved by manufacturer. Remove protective coverings at time of Substantial Completion.

B. Restore finishes damaged during installation and construction period so no evidence remains of correction work. Return items that cannot be refinished in field to shop; make required alterations and refinish entire unit, or provide new units.

END OF SECTION

ETICA GROUP Etica Group Project # 200061.04 This page intentionally left blank. Mobility Solutions & Customer Care Center COMMUNICATIONS IFB 21-06-406 Section 270500 - Page 1

SECTION 270500 - COMMUNICATIONS

PART 1 - GENERAL

1.1 SCOPE OF WORK

A. The Contractor is held responsible to be familiar with the provisions contained herein and with other Sections of this Specification as applicable to the completion of the installation.

B. Work covered by this Section shall consist of furnishing labor, equipment, supplies, materials, and testing unless otherwise specified, and in performing the following operations recognized as necessary for the installation, termination, and labeling of all telecommunications infrastructure as described on the Drawings and/or required by these specifications.

1.2 INTENT OF THE DRAWINGS AND SPECIFICATIONS

A. These Specifications, together with the Drawings accompanying them, are intended to depict the installation requirements necessary to support this Project.

B. Contractor shall furnish materials shown and/or called for on the Drawings but not mentioned in the Specifications, or vice versa, that are necessary for the installation and support of the described work, whether or not specifically called for in both.

C. Contractor shall provide incidental equipment and materials required for the completion of systems included in this contract whether or not specified or shown on the Drawings.

1.3 COMMUNICATION

A. All questions, deviations, comments concerning guideline(s) interpretation, content, and/or use must be submitted in writing to the Project Manager for approval.

B. No deviations from these guidelines shall be incorporated into the project without written approval from the Project Manager.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center COMMUNICATIONS IFB 21-06-406 Section 270500 - Page 2

PART 2 - PRODUCTS

2.1 MATERIALS

A. All materials shall conform to the current applicable industry standards including, but not limited to:

1. NEMA (National Electrical Manufacturers' Association) 2. ANSI (American National Standards Institute) 3. ASTM (American Society for Testing and Materials) 4. ICEA (Insulated Cable Engineers Association) 5. IEEE (Institute of Electrical and Electronic Engineers) 6. NEC (National Electric Code) 7. NESC (National Electrical Safety Code)

B. In addition, all Material shall be Underwriters Laboratories Listed unless otherwise indicated.

C. All products must be new.

PART 3 - EXECUTION

3.1 TELECOMMUNICATIONS INSTALLATION

A. Each Contractor shall be aware of work to be performed by other trades and take necessary steps to integrate and coordinate their work with other trades.

B. The Contractor shall be responsible for furnishing all materials on the drawings or as specified herein for a complete telecommunications system.

C. All telecommunications infrastructure shall be installed in an aesthetically pleasing fashion.

D. All telecommunications infrastructure shall be installed for optimal performance.

E. All telecommunications infrastructure shall be installed and clearly labeled for easy moves, adds, and changes in the future.

F. All work performed in occupied spaces shall be in a manner that allows the Owner to operate the existing facilities on a continuous basis.

G. Construction within new TRs must be substantially complete before the installation of telecommunications cabling. This includes but is not limited to the installation of plywood, cable tray, electrical outlets, light fixtures, sprinklers, ductwork, and grounding. All walls shall also be painted before the installation of telecommunications cabling. Note: Telecommunications Terminal Board shall not be painted.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center COMMUNICATIONS IFB 21-06-406 Section 270500 - Page 3

H. New TRs must be free from dust, dirt, and other foreign materials before the installation of any termination hardware or the termination of copper or fiber optic cables. The door to the telecommunication rooms must be installed and closed during termination.

3.2 TELECOMMUNICATION DEMOLITION

A. Where the relocation of existing PICs is required and the new location will allow the existing cables to reach, the cables may be disconnected and removed back to the hallway raceway system for installation into the new PIC. Where existing cables will not reach, new cables shall be installed to the TR. The new PIC location shall be relabeled. This installation requires a retest of the voice and data cables.

B. Where the removal of existing PICs is required, the contractor shall remove the PIC raceway, conduits, and cables back to the exterior of the TR. Contractor shall notify IndyGo Representative at the time of removal. Owner will remove all items within the TRs. Removal of existing PICs requires as-built information from the contractor. Contractors are to supply a copy of the construction floor plan indicating where the PIC was removed and the labeling information on the PIC.

C. PICs scheduled to be relocated shall be tested by the contractor prior to moving. This is to ensure the permanent link meets the category performance set forth by ANSI/TIA. The contractor is responsible for bringing failed tests to the attention of IndyGo representative before proceeding. After reviewing and verifying the failed results, Indygo Representative will discuss options for repair. Unless the failed result is over distance, the contractor shall re-terminate the jack and re-test to confirm that the termination was not the cause of the problem.

D. Per the NEC, legacy voice and data systems not used within renovated areas shall be removed as part of the project. The Contractor is responsible to bring legacy systems within the proposed renovated areas not identified on the construction documents to the attention of the IndyGo Representative who will verify its usage. Note: Some legacy cabling still contains active circuits which must be verified and relocated in such a manner as to minimize customer disruption.

END OF SECTION 270500

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 1

SECTION 270528 - PATHWAYS FOR COMMUNICATIONS SYSTEMS

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Metal conduits and fittings. 2. Hooks. 3. Wire-mesh cable tray. 4. Boxes, enclosures, and cabinets.

1.2 ACTION SUBMITTALS

A. Product Data: For each type of cable tray.

1. Include data indicating dimensions and finishes for each type of cable tray indicated.

PART 2 - PRODUCTS

2.1 METAL CONDUITS AND FITTINGS

A. Refer to electrical specifications (Division 26) for electrical product requirements. (Conduit, boxes, etc.)

B. Nylon Cable Protectors for conduits 3”- 6”.

C. Nylon Cable Protectors for conduits 2” and 2-1/2”.

D. Nylon Cable Protectors for conduits 1-1/4” and 1-1/2”.

E. All raceway products containing telecommunications cabling shall be fiber ready to allow for minimum bend radius requirements.

F. Insulating bushing on all telecommunication conduits shall be plenum rated.

2.2 HOOKS

A. Description: Prefabricated sheet metal cable supports for telecommunications cable.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 2

B. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. MonoSystems, Inc. 2. Panduit Corp. 3. Wiremold / Legrand.

C. Listed and labeled as defined in NFPA 70, by an NRTL, and marked for intended location and application.

D. Comply with TIA-569-D.

E. Galvanized steel.

F. J shape.

2.3 CABLE TRAY

A. GENERAL REQUIREMENTS FOR CABLE TRAYS

1. Cable Trays and Accessories: Identified as defined in NFPA 70 and marked for intended location, application, and grounding.

a. Source Limitations: Obtain cable trays and components from single manufacturer.

2. Sizes and Configurations: See Drawings for specific requirements for types, materials, sizes, and configurations. 3. Structural Performance:

a. Uniform Load Distribution: Capable of supporting a uniformly distributed load on the indicated support span when supported as a simple span and tested according to NEMA VE 1. b. Concentrated Load: A load applied at midpoint of span and centerline of tray. c. Load and Safety Factors: Applicable to both side rails and rung capacities.

B. WIRE-MESH CABLE TRAY

1. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to the following:

a. Chalfant Manufacturing Company. b. Caddy, nVent, WBT c. Cooper Industries; Cooper B-Line; an Eaton business. d. GS Metals Corp. e. Cope Cable Tray; A Part of Atkore International.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 3

f. Enduro Composites Inc. g. Hubbell Incorporated; Wiring Device-Kellems. h. Cablofil; Legrand US. i. MonoSystems, Inc. j. MP Husky USA Cable Tray & Cable Bus.

2. Description:

a. Configuration: Galvanized- steel wire mesh, complying with NEMA VE 1. b. Width: As indicated on Drawings. c. Minimum Usable Load Depth: As indicated on Drawings. d. Straight Section Lengths: 10 feet (3.0 m), except where shorter lengths are required to facilitate tray assembly. e. Structural Performance: Capable of supporting a maximum cable load, with a safety factor of 1.5, plus a 200-lb (90-kg) concentrated load, when tested according to NEMA VE 1. f. Class Designation: Comply with NEMA VE 1, Class 10A. g. Splicing Assemblies: Bolted type using serrated flange locknuts. h. Splice-Plate Capacity: Splices located within support span shall not diminish rated loading capacity of cable tray.

3. Materials and Finishes: a. Steel:

1) Straight Sections and Fittings: Steel complies with the minimum mechanical properties of ASTM A 1011/A 1011M, SS, Grade 33 or ASTM A 1008/A 1008M, Grade 33, Type 2. 2) Steel Tray Splice Plates: ASTM A 1011/A 1011M, HSLAS, Grade 50, Class 1. 3) Fasteners: Steel complies with the minimum mechanical properties of ASTM A 510/A 510M, Grade 1008. 4) Finish: Hot-dipped galvanized after fabrication, complying with ASTM A123/A123 M, Class B2.

a) Hardware: Galvanized, ASTM B 633 or Chromium-zinc plated, ASTM F 1136.

5) Finish: Electrogalvanized after fabrication, complying with ASTM B 633.

a) Hardware: Galvanized, ASTM B 633.

C. CABLE TRAY ACCESSORIES

1. Fittings: Tees, crosses, risers, elbows, and other fittings as indicated, of same materials and finishes as cable tray. 2. Barrier Strips: Same materials and finishes as for cable tray as required to separate different systems (fire alarm, telecom, access control, etc.)

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 4

3. Cable tray supports and connectors, including bonding jumpers, as recommended by cable tray manufacturer.

2.4 BOXES, ENCLOSURES, AND CABINETS

A. Refer to electrical specifications (Division 26) for electrical product requirements. (Conduit, boxes, etc.)

B. Description: Enclosures for communications.

C. General Requirements for Boxes, Enclosures, and Cabinets:

1. Comply with TIA-569-D. 2. Boxes, enclosures, and cabinets installed in wet locations shall be listed and labeled as defined in NFPA 70, by an NRTL, and marked for use in wet locations. 3. Box extensions used to accommodate new building finishes shall be of same material as recessed box. 4. Device Box Dimensions: 4 11/16” H x 4 11/16” W x 3 1/4” D.

D. Sheet Metal Outlet and Device Boxes: Comply with NEMA OS 1 and UL 514A.

PART 3 - EXECUTION

3.1 GENERAL REQUIREMENTS

A. The intention of the telecommunications pathways is to provide a route between BDF and IDF rooms, routes from the IDFs throughout building floors to hallways, and routes from hallway distribution systems into rooms to individual data jacks for telecommunications cabling.

B. Installation of new pathways shall not interfere with existing pathways in such a way that installation of new cables within the existing pathway is made more difficult.

C. All conduit termination points shall be fitted with a plastic bushing. Conduits and fittings with threads shall have a threaded plastic bushing.

3.2 PATHWAY REQUIREMENTS FOR ENTRANCE CONDUITS

A. If the entrance conduits exceeds the 180 degree of total bends limitation, an appropriate sized junction box is required. Access to the junction box from below shall be maintained.

B. Install cable waterfalls on outside plant conduits entering the room from above where the incoming cable will transition to another raceway more than 6” vertically.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 5

3.3 HORIZONTAL DISTRIBUTION SYSTEM

A. Corridor Cable Tray System & J-Hooks

1. Complete wall mounted or suspended cable basket system or J-Hooks with necessary accessories. Install entire system in accordance with manufacturer’s minimum installation practices and all local governing codes. 2. Coordinate installation of system with other trades to allow a minimum of 12” above, 6” in front, and 3” below of clearance from piping, conduits, ductwork, etc. 3. System shall not be loaded beyond 60% of manufacturer’s recommended load capacity. 4. Install wall system on one side of the hallway to minimize conflicts with mechanical ductwork or as shown on drawings and where applicable. 5. Where distribution system encounters a wall, install sufficient 4” EMT sleeves or restorable fire stopping sleeves through the wall so cabling does not exceed 20% fill. 6. Where cable basket is exposed below ceiling, install the appropriate solid bottom and side inserts to conceal cables. 7. Install cable basket dropouts where more than 10 cables exit the distribution system. 8. Manufacturer of cable basket in corridors shall be WBT, Cablofil, B-Line Systems, or Owner approved equal. 9. Provide factory manufactured tee fittings and 90 degree fittings to maintain the tray performance characteristics. Utilize factory splice connectors to maintain the tray ground integrity.

B. Sleeves

1. Install a cable waterfall on all 4” conduit sleeves containing cables that transition more than 6” vertically from the sleeve down to another raceway (conduit or cable tray). 2. Install nylon cable protectors at the leading conduit edge. These protectors would not be used on conduits where the cable waterfall is required (more than 6” of vertical drop). 3. Where cables must penetrate fire-rated walls between sections of skeletal conduit or cable tray sections, install sufficient 4” EMT sleeves or restorable fire stopping sleeves through the wall so cabling does not exceed 20% fill.

3.4 CABLE TRAY INSTALLATION

A. Install cable tray and support systems according to NEMA VE 2.

B. Install cable tray as a complete system, including fasteners, hold-down clips, support systems, barrier strips, adjustable horizontal and vertical splice plates, elbows, reducers, tees, crosses, cable dropouts, adapters, covers, and bonding.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 6

C. Install cable tray, so that the tray is accessible for cable installation and all splices are accessible for inspection and adjustment.

D. Remove burrs and sharp edges from cable trays.

E. Fasten cable tray supports to building structure.

F. Design fasteners and supports to carry cable tray, cables, and a concentrated load of 200 lb (90 kg). Comply with requirements in Section 260529 "Hangers and Supports for Electrical Systems.

G. Place supports, so that spans do not exceed maximum spans on schedules, and provide clearances shown on Drawings. Install intermediate supports when cable weight exceeds the load-carrying capacity of tray rungs.

H. Construct supports from channel members, threaded rods, and other appurtenances furnished by cable tray manufacturer. Arrange supports in trapeze or wall-bracket form as required by application. Center-hung supports are not acceptable.

I. Support assembly to prevent twisting from eccentric loading.

J. Support wire-basket cable trays with trapeze hangers or wall brackets.

K. Do not install more than one cable tray splice between supports.

L. Make connections to equipment with flanged fittings fastened to cable trays and to equipment. Support cable trays independent of fittings. Do not carry weight of cable trays on equipment enclosure.

M. Make changes in direction and elevation using manufacturer's recommended fittings.

N. Make cable tray connections using manufacturer's recommended fittings.

O. Seal penetrations through fire and smoke barriers. Comply with requirements in Section 078413 "Penetration Firestopping."

P. Install capped metal sleeves for future cables through firestop-sealed cable tray penetrations of fire and smoke barriers.

Q. Install cable trays with enough workspace to permit access for installing cables.

R. Install barriers to separate cables of different systems, such as fire alarm, communications, and data processing, or of different insulation levels, such as 600, 5000, and 15 000 V.

S. Install permanent solid bottoms and sides where cable tray is exposed to view.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 7

3.5 CABLE TRAY GROUNDING

A. Ground cable trays according to NFPA 70 unless additional grounding is specified. Comply with requirements in Section 260526 "Grounding and Bonding for Electrical Systems."

3.6 STATION CONDUITS

A. Minimum Pathway Size: 1-inch for cooper or optical-fiber cables.

B. Provide station conduits from work area outlet (WA) to between 12”-18” of hallway distribution systems of 1” EMT minimum or appropriate size as shown on the Drawings or as specified herein for installation of telecommunications cables.

C. Provide an insulating press fit bushing on all telecommunications conduits including interconnecting nipples and stub to distribution system. To prevent conflicts with other cables, conduits to cable tray or J-Hook system shall be stubbed not less than 6" above or below cable tray / J-Hook center line. Where space permits, every effort shall be made to bend station conduits down such that the flow of installed cables promote the minimum length back to the IDF and the least amount of bends in the cables. Bushings must be rated to be used in an environmental air handling space (Plenum).

D. Provide nylon pull cord in each conduit to hallway distribution system.

E. Indelibly mark station conduit at hallway distribution end with Room # that conduit serves.

F. Indelibly mark station conduits that directly enter the telecommunications room.

G. The use of pulling LBs is prohibited.

H. Do not include more than two 90 degree bends between pulling points when installing station conduit runs. If the path of the station conduits requires more than 180 degrees of total bends, installation of an appropriate sized junction box or “C type” condulet is required.

I. Place an appropriate sized junction box or “C type” condulet in each individual station conduit run that exceeds 100ft in length.

J. The use of a third bend in a conduit is only acceptable if:

1. The total conduit run does not exceed 33ft. 2. The conduit size is increased to the next trade size. 3. One of the bends is located within 12” of the cable feed end.

K. Ceiling grid support wires shall not be used to support telecommunications raceways or cables.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 8

L. Conduits shall be anchored so that they are RIGID to movement.

3.7 JUNCTION BOX REQUIREMENTS FOR STATION CONDUITS

A. If the station conduit route exceeds the 180 degree of total bends limitation, an appropriate sized junction box or “C type” condulet is required within a straight section of the conduit run.

B. Each station conduit run requires a separate junction box or “C type” condulet. The sharing of a junction box by multiple conduits is prohibited.

C. A junction box shall not be used in place of a bend. All junction boxes or “C type” condulet in station conduit paths shall be installed within a straight section of the conduit run.

3.8 INSTALLATION

A. Comply with the following standards for installation requirements except where requirements on Drawings or in this Section are stricter:

1. NECA 1. 2. NECA/BICSI 568. 3. TIA-569-D. 4. NECA 101 5. NECA 105.

B. Comply with NFPA 70 limitations for types of pathways allowed in specific occupancies and number of floors.

C. Comply with requirements in Section 078413 "Penetration Firestopping" for firestopping materials and installation for penetrations through fire-rated walls, ceilings, and assemblies.

D. Comply with requirements in Section 270529 "Hangers and Supports for Communications Systems" for hangers and supports.

E. Comply with requirements in Section 270544 "Sleeves and Sleeve Seals for Communications Pathways and Cabling" for sleeves and sleeve seals for communications.

F. Keep pathways at least 6 inches away from parallel runs of flues and steam or hot- water pipes. Install horizontal pathway runs above water and steam piping.

G. Complete pathway installation before starting conductor installation.

H. Arrange stub-ups so curved portions of bends are not visible above finished slab.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 9

I. Conceal rigid conduit within finished walls, ceilings, and floors unless otherwise indicated. Install conduits parallel or perpendicular to building lines.

J. Support conduit within 12 inches of enclosures to which attached.

K. Hooks:

1. Size to allow a minimum of 25 percent future capacity without exceeding design capacity limits. 2. Shall be supported by dedicated support wires. Do not use ceiling grid support wire or support rods. 3. Hook spacing shall allow no more than 6 inches of slack. The lowest point of the cables shall be no less than 6 inches adjacent to ceilings, mechanical ductwork and fittings, luminaires, power conduits, power and telecommunications outlets, and other electrical and communications equipment. 4. Space hooks no more than 5 feet o.c. 5. Provide a hook at each change in direction.

L. Mount boxes at heights indicated on Drawings. If mounting heights of boxes are not individually indicated, give priority to ADA requirements. Install boxes with height measured to center of box unless otherwise indicated.

M. Recessed Boxes in Masonry Walls: Saw-cut opening for box in center of cell of masonry block and install box flush with surface of wall. Prepare block surface to provide a flat surface for a raintight connection between box and cover plate or supported equipment and box.

N. Horizontally separate boxes mounted on opposite sides of walls, so they are not in the same vertical channel.

O. Support boxes of three gangs or more from more than one side by spanning two framing members or mounting on brackets specifically designed for the purpose.

P. Fasten junction and pull boxes to or support from building structure. Do not support boxes by conduits.

3.9 SLEEVE AND SLEEVE-SEAL INSTALLATION FOR COMMUNICATIONS PENETRATIONS

A. Install sleeves and sleeve seals at penetrations of exterior floor and wall assemblies. Comply with requirements in Division 26 "Sleeves and Sleeve Seals."

3.10 PROTECTION

A. Protect coatings, finishes, and cabinets from damage or deterioration.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 10

1. Repair damage to galvanized finishes with zinc-rich paint recommended by manufacturer.

3.11 FIRE STOPS

A. In all buildings, floor/ceiling assemblies, stairs, and elevator penetrations must be sealed with a minimum 2-hour fire stop assembly, unless otherwise noted. Penetrations through non-fire rated walls do not require fire-stopping but will require sleeves.

B. Contact Architect to identify walls which are fire-rated construction if not shown on architectural drawings.

C. Communication pathways requiring fire stopping shall utilize removable/re-usable fire stopping putties for ease of Moves, Adds, and Changes.

D. All fire stopping penetrations shall conform to the recommended practices listed in UL1479 or ASTM E814 and must be labeled with the UL1479 or ASTM E814 reference number, dated, and signed by the technician who installed the fire stopping material.

3.12 TABLE OF JUNCTION BOX REQUIREMENTS Size of Box Increased width Conduit Type Conduit Width Length Depth for each Size additional conduit

Station 1” 6” 6” 4” --- Station 1½” 6” 6” 4” --- Station 2” 8” 8” 4” --- Station 2¼” 12” 12” 6” --- Station 2½” 12” 12” 6” --- Riser 3” 6” 24” 6” --- Riser 4” 8” 36” 8” --- Entrance 2” 8” 36” 4” 5” Entrance 2½” 10” 42” 5” 6” Entrance 3” 12” 48” 5” 6” Entrance 4” 15” 60” 8” 8”

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center PATHWAYS FOR COMMUNICATIONS IFB 21-06-406 SYSTEMS Section 270528 - Page 11

END OF SECTION 270528

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center TERMINATION BLOCKS AND PATCH PANELS IFB 21-06-406 Section 271119 - Page 1

SECTION 271119 - TERMINATION BLOCKS AND PATCH PANELS

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Patch Panels. 2. Termination Blocks. 3. Wire management.

1.2 ACTION SUBMITTALS

A. Product Data: For each type of product.

1.3 CLOSEOUT SUBMITTALS

A. Operation and Maintenance Data: Include in all manufacturers' packing-label warnings and instruction manuals.

1.4 QUALITY ASSURANCE

A. Installer Qualifications: Cabling installer must have personnel certified by BICSI on staff.

1. Layout Responsibility: Preparation of Shop Drawings shall be under direct supervision of RCDD. 2. Installation Supervision: Installation shall be under direct supervision of Installer 2, Copper or Fiber, who shall be present at all times when Work of this Section is performed at Project site. 3. Field Inspector: Currently registered by BICSI as RCDD to perform on-site inspection.

PART 2 - PRODUCTS

2.1 MANUFACTURER

A. Basis of Design: Panduit. Equivalent manufacturers to be approved by owner and Engineer.

2.2 110 BLOCKS

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center TERMINATION BLOCKS AND PATCH PANELS IFB 21-06-406 Section 271119 - Page 2

A. 110 Termination Blocks for Copper Riser Cables

1. Panduit #P110KB1005Y, field termination kit a. Field termination kit includes wiring block, (20) 5-pair connector blocks, and labels. 2. Panduit #P110BW100-X, 110 Block 3. Panduit #P110CB5-XY, 5-pair 110 Connecting Block 4. Panduit #P110LH, Designation Label Holder 5. Panduit #DSL110, 110 Designation Labels

B. 110 Termination Blocks for Copper Horizontal Cables

1. Panduit #P110KB1004Y, field termination kit a. Field termination kit includes wiring block, (20) 4-pair connector blocks, (4) 5-pair connector block, and labels. 2. Panduit #P110BW100-X, 110 Block 3. Panduit #P110CB4-XY, 4-pair 110 Connecting Block 4. Panduit #P110LH, Designation Label Holder 5. Panduit #DSL110, 110 Designation Labels

2.3 PATCH PANELS

A. Panduit #CPPA24FMWBLY, Category 6a, 24-port angled modular patch panel, with TG style mini-com jacks and rear-mounted faceplates.

2.4 WIRE MANAGEMENT FOR EQUIPMENT FRAMES

A. Horizontal Wire Management for copper is not required between Category 6a angled patch panels.

B. One Panduit #NMF4 Horizontal Wire Management shall be installed between 23RU (42” AFF) and 26RU on equipment frames.

C. Vertical Wire Management

1. Panduit #PR2VD12 wire management shall be installed on either side of equipment frames in buildings utilizing Category 6a cabling.

D. One Panduit #SRB19MDBL Strain Relief Bar shall be installed on the back (termination side) of the Equipment Frame starting at the uppermost patch panel and on every other patch panel underneath to relieve cable strain. Utilize hook and loop cable ties (Velcro© or owner-approved equivalent) to relieve cable strain.

2.5 TELECOMMUNICATIONS WIRE MANAGEMENT

A. Panduit #CMVDR1, Plastic D-rings for Owner furnished cross connects.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center TERMINATION BLOCKS AND PATCH PANELS IFB 21-06-406 Section 271119 - Page 3

B. Panduit #CMVDR2, Plastic D-rings for Vertical and Horizontal Cable Management on plywood.

PART 3 - EXECUTION

3.1 110-BLOCK INSTALLATION

A. The telecommunications rooms shall contain wiring blocks as required to terminate all incoming pairs and all outgoing pairs.

B. Locate telephone wiring blocks on fire-treated plywood backboards as specified on the Drawings or as specified herein.

C. BDF block labeling for riser cables shall designate the corresponding destination IDF wiring block.

D. BDF/IDF terminal boards shall be equipped with “D” rings for horizontal and vertical wire management.

E. Horizontally separate 110 blocks 12” apart for horizontal cable by floor. Start 110 blocks 5’-6” AFF. In the BDF, horizontally separate 110 blocks 12” away from entrance protectors. If entrance protectors are not installed, leave enough space as specified above (protector dimension= 14.75” width by 11” height).

F. Horizontal cables shall enter new 110 blocks from the left side. Cables shall not be routed behind 110 blocks.

G. Telecommunication rooms feeding multiple floors

1. Install 110 blocks for each floor in a separate vertical row with each row separated 12” apart horizontally.

H. When terminating cabling on new 110 blocks, PICs in the same room shall be punched down on adjacent 4-pair connecting blocks and the rooms shall be in numerical order.

I. When terminating new cabling on existing 110 blocks, work area outlets in the same room shall be punched down on adjacent 4-pair connecting blocks and the rooms shall be in as close to numerical order as practical.

3.2 PATCH PANEL INSTALLATION

A. Each telecom room shall contain patch panels as required to terminate all pairs on its respective floor area or floors served. Provide quantity of patch panels as required to terminate all cable pairs.

B. Locate data patch panels in 19” equipment frames as specified on the drawings or as specified herein.

APPLIED ENGINEERING Applied Engineering Project No. 21-026 Mobility Solutions & Customer Care Center TERMINATION BLOCKS AND PATCH PANELS IFB 21-06-406 Section 271119 - Page 4

C. Patch panels to be mounted in equipment frames no higher than 6’-0” A.F.F. and no lower than 3’-6” (42”) A.F.F. (39RU – 25RU).

D. Where additional equipment frames are required, separate the frames using one 12” vertical cable management device.

E. Include vertical cable management on both sides of every equipment frame. Multiple frames shall be separated by a 12” vertical cable management device.

F. Each category of cabling shall have its own patch panel and corresponding jacks.

END OF SECTION 271119

APPLIED ENGINEERING Applied Engineering Project No. 21-026 6/14/2021 9:28:19 AM BIM 360://IndyGo Mobility Phase II & III/IndyGo Mobility Phase II + III.rvt

706 OU OU 707

0 X CONCRETE GRAVEL A/C A/C A/C A/C A/C A/C A/C

707OU G

706

0 WATER SPIGOT FFE CENTER OF DOOR

707

FO F.F.E. = 707.32

OU EM GRASS X

OU SV SV X 1 IN. DIA. WATER IRRIGATION LINE MULCH (PER UTILITY MARKINGS) COMES FROM BUILDING B B GV GM G

GV FO

F.F.E. = 707.28

X FO

SEE DETAIL S-8, C801 OR APPROVED EQUAL. OU TYP. ALONG WALK AT DOWNSPOUTS. ACO DRAIN CROSS SIDEWALK

UT 707 FFE SAN

G X CO BOULDER DEPARTMENT CONNECTION INFORMATION. PLEASE NOTE: SEE MEP DRAWINGS FOR FIRE

MULCH

SAN X

G CO

OU GRAVEL FO

18'

1 G X

I V 12 LF OF 2" PVC DOMESTIC WATER COORDINATE WITH MEP PLANS WITH ISOLATION VALVE. POST INDICATOR VALVE MICHIGAN STREET

OU BACKFLOW PREVENTER 2 X FT. METAL BOX OVER G BOULDER MULCH

G W 184 LF OF 6" C900 FIRE SERVICE LINE COORDINATE WITH MEP PLANS CO

W BOULDER

G MULCH

UT PIPE FROM UPSTREAM SIDE OF SEPARATOR TO BUILDING BY OTHERS. W

706 INVERT AT DOWNSTREAM SIDE OF SEPARATOR = 702.97.

OU BOULDER MULCH W

G CONNECT TO OIL/WATER SEPARATOR. COORDINATE WITH MEP PLANS F.F.E. = 707.32 F.F.E. = 707.34

OU BOULDER

UT MULCH

706 COORDINATE CONTRACTOR SHALL TAP BY CEG

W FFE FFE B CO B

707

OU EXISTING WATER MAIN CONTRACTOR SHALL FIELD VERIFY THE SIZE OF

707 W

707 ASPHALT T

W GRAVEL CONCRETE 1. NOTES: 5. 3. 2. 6. 4.

G 18 INCHES VERTICAL SEPARATION BETWEEN THE SANITARY SEWER AND BENCHWALL FORMATION, SEALING CRACKS, CHIMNEY DEAL BE REHABILITATED TO CURRENT CEG DESIGN STANDARDS, I.E. MAINTAINED, A CONCRETE CRADLE SHALL BE INSTALLED. UTILITY LOCATIONS BEFORE CONSTRUCTION BEGINS. INSTALLATION, ETC. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO FIELD VERIFY ALL CONNECTIONS TO EXISTING MANHOLES REQUIRE THAT THE STRUCTURE GROUP (CEG) CURRENT SPECIFICATIONS. COMPLIANCE WITH OSHA STANDARDS. WATER LINE. IF A MINIMUM SEPARATION OF 18 INCHES CANNOT BE AND CONSTRUCTION SHALL FOLLOW CEG'S CURRENT STANDARDS. ALL SANITARY SEWER AND WATER MATERIALS, TESTING SPECIFICATIONS THERE IS TO BE A MINIMUM OF 10 FEET HORIZONTAL SEPARATION AND ALL SEWERS, MANHOLES, AND CASTINGS SHALL BE PER CITIZENS ENERGY ALL CONSTRUCTION ACTIVITY ON THIS SITE IS TO BE PERFORMED IN MKG TF CONCRETE

706 TVR ER TVR TVR OU OU OU OU OU OU OU UT TVR UT REPLACE CURB UT UT W OU PAVEMENT REPLACEMENT PER

INDIANAPOLIS DPW C801. STANDARDS. SEE DETAIL S-7,

TRENCH BACKFILL AND OU UT

706 OU 73 LF OF 6" PVC @ 1.0% MIN. SLOPE

OU OU WV

G G G G G

705 G

GV OU

OU 103 OU OU

OU REPLACE CURB

705 CONCRETE CONTRACTOR SHALL FIELD SIDE OF TREMONT ST. SANITARY MAIN ON EAST CONNECT TO EXISTING VERIFY LOCATION AND DEPTH N. TREMONT STREET 0 GRAPHIC SCALE (FEET)

OU 705

WV OU OU

N OU 10

OU TBM #11

OU 20 EM OU OU OU OU OU OU OU OU OU OU 1 # intended by The Etica Group, Inc. inc. is not responsible for any damage or injury resulting use of this document for any purpose other than that purpose other than that intended by The Etica Group, Inc. disclaims all warranties, express or implied , relating to the constitutes an impermissible misuse. The Etica group, Group, Inc. is prohibited. Use of this document for any of the document without permission from The Etica Group, Inc., its heirs, and assigns. Modification or reuse Group, Inc. It is intended solely for use by The Etica from misuse of this document. The Etica Group, Inc. This construction document is the property of The Etica DATE ISSUED: 6.15.21 BID DOCUMENTS ADDENDUM #2 C401 DESCRIPTION UTILITY REVISION SCHEDULE PROFESSIONAL SEAL: PROJECT NUMBER: DRAWING TITLE: SHEET NUMBER: PLAN 0200061.04 KDK/KMB DISCLAIMER: DRAWN BY: Mobility Solutions & Customer Care Center Facility 2425 W. Michigan St., Indianapolis, IN 46222 DRAWN BY KMB Indianapolis Public Transportation Corporation CHECKED BY: 07/08/21 DATE ISSUED JAD 1501 W. Washington Street Indianapolis, IN 46204 0 1/2" 1" 2" ORIGINAL SHEET SIZE IS 30"x42" (ARCH E1) 7/7/2021 4:11:10 PM AESI Proj. No: 21 -056 2. SCHEDULE 2. NOTES SCHEDULE 1. NOTES NOTES: MOTOR CONTROLLER SCHEDULE NTTGLOCATION UNITTAG CVF MAINTENANC MC-VEF1 CV2WORKAREA MC-VF2 MAINTENANC MC-VF1 EAREA 131 EAREA 131 130 EQUIPMENT SERVED E- 0 0A2 1 0 A 20 A 20 3 V 208 A 8 2 VEF-1 F231 0 5A2 1 1 0 0 A 25 A 25 A 25 A 25 3 3 V 208 V 208 A 11 A 11 3 3 VF-2 VF-1 PFAVLSPH VOLTS FLA HP OO AACONTROLLERDATA MOTORDATA CIRCUITBREAKER RM TRIP FRAME NEMA SIZE 2 ENCLOSURE NEMA NOTES: LIGHTINGFIXTURE SCHEDULE YETGDSRPINMOUNTING DESCRIPTION TYPETAG 1 EXTERIORPACK LIGHT BATTERY WALL WITH S1A 4 EEA TLT IH,01VDMIGSRAELD40 35 LED LED SURFACE PENDANT GENERALUTILITY LIGHT, 0-10VDIMMING F4B GENERALUTILITY LIGHT, 0-10VDIMMING F4A MEMERGENCYLIGHT BATTERY WITH BACKUP, EM XEMERGENCYEXIT SIGN WITHBATTERY FX 1EXTERIORPACK WALL LIGHT WITH S1 88 ON A IH,01VDMIGPNATLD1400l LED 350 PENDANT 8000lm ROUND 8" CAN LIGHT, 0-10VDIMMING LED 1400 8'LINEAR WITH APERATURE, 4" 0-10V F8 PENDANT LED F5 RECESSED HIGHBAY LIGHT, 0-10VDIMMING ROUND 8" CAN LIGHT, 0-10VDIMMING F3 LAY-INGRI F2 2X4TROFFER, CURVED LENS, 0-10VDIMMING F1 NOTES HIGH-IMPACTFLAME-RATED PLASTIC. BACKUP,WITH GREEN LETTERING BACKUPAND PHOTOSENSOR 5..EITN OD26 -00 .0- 0A1EXISTINGL **ACCU-935,... -- **ACCU-831,... -- 3 **ACCU-725,... A 20 1 AC-4A 20 19,... -- AC-3 -- 13,... 0.00 0.00 -- AC-27,9... AC11,3,5 0.00 0.00 0.00 0.00 ------A 60 2 A 60 2 A 60 2 EXISTINGLOAD 23,... EXISTINGLOAD 19,... EXISTINGLOAD 15,... Spare7,9... Total Load (KVA) Other Load (KVA) Motor Load (KVA) Heating Load (KVA) Receptacle Load (KVA) Lighting Load (KVA) Feed From: Voltage SPD: Branch Panel... Total Load (KVA) Other Load (KVA) Motor Load (KVA) Heating Load (KVA) Receptacle Load (KVA) Lighting Load (KVA) Feed From: Voltage SPD: Branch Panel... k odNm oeRating Pole Load Name Ckt Rating Pole Load Name Ckt 3EITN OD12 -00 .0- 0A1EITN OD1 EXISTINGLOAD ------1 -- A 20 -- 0.00 0.00 -- 0.00 0.00 -- -- 0.00 0.00 A 20 -- A 20 1 1 A 20 1 Space 31 Spare 29A. -29B. Spare 29 Spare 27A. -27B. Spare 27 EXISTINGLOAD 13 1NWACSILT IT13 -00 .5------1.75 0.00 -- A 30 1 ACCESSIBLITY NEW LIFT 41 XSIGLA 0A- .000 -3 XSIGLA 2 EXIST EXISTINGLOAD 1 1 A 20 A 30 -- -- 0.00 0.00 0.00 0.00 -- -- 0.00 A 20 A 20 1 1 -- A 20 5A.Spare -5B. Spare 1 5 5A.EXISTING LOAD 5B. EXISTING - LOAD 3 EXISTINGLOAD 1 ------PHOTOSENSOR DIMMING 120/208Wye No P1 MDP 120/208Wye No PANEL"D" once V eadFco Demand KVA Demand Factor Connected KVA Demand KVA Demand Factor Connected KVA 140 A11 4587.00VA 1.10 4164.00VA 15 E 07 MoldedCase Electronicwith 10.60 Trip Unit 10.75 0.80 NEC 98.42 13.26 11.50 0.00 ALSRAELD0l 50K5W10VDUALLITESE SERIES V 120 5 W K 3500 lm 0 LED WALL/SURFACE DUALLITEEV SER V 120 5 W K 3500 3500lm LED WALL/SURFACE EDN E 70l 50K3 2 FINELITEHP-4 SERIE V 120 37 W K 3500 3700lm LED PENDANT -- -00 .0------0.00 0.00 ------17 .4Ohr oo 5A1*FRAE934 **FURNACE-9 30 **FURNACE-7 28 BREAKRM ICE MAKER -- 2 -- A 20 1 1 12 -- HVAC A 20 -- 10 LTSTRAINING STORAGE A 15 LTS --HALL BREAKROOM 1 -- A 15 -- -- Other; --Motor -- -- 1.75 -- Other; Motor 1.44 1.69 1 1.80 -- 1 A 20 -- 1.24 A 20 1.77 0.00 0.00 1 -- 0.00 1 1.44 -- 0.00 A 20 1.80 -- 0.00 A 20 0.00 ------0.00 0.00 -- 0.00 0.00 -- 0.00 ------0.00 -- 0.00 -- 22.00 -- 0.00 ------0.00 ------0.00 -- 22.00 ------18 -- -- EXISTINGLOAD ------10 -- -- EXISTINGLOAD -- 12 -- 12A.Spare-12B. 3 Spare ------A 25 ------1 -- -- A 20 -- -- 1 1 A 20 -- A 20 -- 0.00 0.00 -- -- 0.00 0.00 0.00 0.00 0.00 0.00 -- 0.00 0.00 ------5AOhr17 .4Ohr oo 5A1*FRAE832 **FURNACE-8 26 BREAKRM COFFEE/WATER 2 A 20 1 1 A 20 A 15 3 Motor A 30 0.00 1.44 3 Other; Motor A 30 -- 1 -- A 20 -- 1.24 Other -- 1 1.77 A 20 Other 0.00 1.80 A 20 0.00 Other 0.00 Receptacle 3 A 25 -- 0.00 2 0.00 A 25 -- 0.00 3 0.00 A 30 -- 3 11.50 22.00 A 30 8 -- EXISTINGLOAD 3 A 30 3 A 30 3 1 A 20 -- 0.00 0.00 -- A 25 3 ALLD40 m30 0 2 HUBBELLNC4 SERIES HUBBELLNC4 SERIES V 120 V 120 100W 100W K 3500 4000lm K 3500 4000lm LED LED WALL WALL Enclosure: A m p : Main: New/Exist: Enclosure: A m p : Main: New/Exist: E 20l 50K2 2 COLUMBIALCAT24 SERIES V 120 28 W K 3500 3200lm LED D NEC Type Type Type1 A 200 MCB EX IST Type1 A 100 MLO EX IST od. KA KA KA Load... C (KVA) B (KVA) A (KVA) Load... Load... C (KVA) B (KVA) A (KVA) Load... YELMN EPRTR AT VOLTS WATTS TEMPERATURE LUMENS TYPE PANELBOARD SCHEDULE PANELBOARD SCHEDULE 97 V 00kA28.7 kVA 30.0 kVA 39.74 kVA .0kA00kA0.0 kVA 0.0 kVA 0.00 kVA 95.44 0.00 0l 50K3 2 COLUMBIAMPS SERIES COLUMBIAMPS SERIES V 120 V 120 34 W 34 W K 3500 00lm K 3500 00lm Feeder: Kaic Rating: Mounting: Location: Feeder: Kaic Rating: Mounting: Location: m30 8W10VLITEFRAMELC8SL SERIES V 120 18 W K 3500 lm 50K1 2 LITEFRAMELC8SL SERIES V 120 18 W K 3500 m oddCs ihFxdTi nt*USE EXISITING BRE MoldedCase Electronicwith Trip iUnit (LSI) Molded CaseFixedwith Trip Unit MoldedCase Electronicwith Trip iUnit (LSI) MoldedCase Electronicwith Trip Unit (LI) Molded CaseFixedwith Trip Unit Trip Unit Description Trip Unit Description .0- 0A1EITN OD4 EXISTINGLOAD 1 A 30 -- 0.00 Surface CORRIDOR157 Surface ELECTRICAL156 LAMPS 2W10VHIMILAYANHIGH BAY-HHB SERIES V 120 62 W K 0 L)**PROVIDE BREAKER NEW (LI) Type Type Date Project No. Project Name: Date Project No. Project Name: aigPl odNm Ckt Load Name Pole Rating Ckt Load Name Pole Rating Notes: Notes: LUMENWERXVIA SERIES 4 SURE-LITESAPEL SERIES AppliedEngineering Services (317) 810-4141 6.15.21 0200061.04 MobilitySolutions & Customer Care Center Facility AppliedEngineering Services (317) 810-4141 6.15.21 0200061.04 MobilitySolutions & Customer Care Center Facility METALUXSNLED SERIES METALUXSNLED SERIES LITHONIASERIES ELM2L METALUX24CZ2 SERIES LITHONIACPHB SERIES LITHONIAARC2 SERIES LITHONIAARC2 SERIES SURE-LITESCX SERIES LITHONIAZL1D SERIES LITHONIAZL1D SERIES LITHONIA2BLT SERIES LUMARKXTOR SERIES LUMARKXTOR SERIES ORAPPROVED EQUAL ORAPPROVED EQUAL ORAPPROVED EQUAL ORAPPROVED EQUAL ORAPPROVED EQUAL METALUXSERIES VHB ORAPPROVED EQUAL ORAPPROVED EQUAL ORAPPROVED EQUAL ORAPPROVED EQUAL ORAPPROVED EQUAL ORAPPROVED EQUAL MARKSLOT SERIES 4 LITHONIALE SERIES AUATRR NOTES MANUFACTURERS HALOHC8 SERIES HALOHC8 SERIES LITHONIALDN6 LITHONIALDN6 AKER IES S N OD6 LOAD ING *W- 40,... **EWH-2 *U- 36,... **PUH-1 pc 32 Space pr 26,... Spare 20,... Spare H48 AHU4 6 AHU3 4 AHU2 2 AHU1 C620,... AC-6 14,... AC-5 A 16 OAD ------4 7..Spare27,... Spare23,... Feed From: Voltage SPD: Branch Panel... Total Load (KVA) Other Load (KVA) Motor Load (KVA) Heating Load (KVA) Receptacle Load (KVA) Lighting Load (KVA) Feed From: Voltage SPD: Branch Panel... Total Load (KVA) Other Load (KVA) Motor Load (KVA) Heating Load (KVA) Receptacle Load (KVA) Lighting Load (KVA) k odNm oeRating Pole Load Name Ckt k odNm oeRating Pole Load Name Ckt , Spare 7,9 7EITN OD12 -00 .0- 0A1EITN OD1 EXISTINGLOAD 1 EXISTINGLOAD 1 1 A 20 1 -- A 20 A 30 ------0.00 0.00 -- 0.00 0.00 0.00 0.00 0.00 0.00 ------A 20 A 20 1 A 20 1 SpaceA 20 33 1 1 Spare 21 Spare 19 EXISTINGLOAD 17 EXISTINGLOAD 15 EXISTINGLOAD 13 EXISTINGLOAD 11 5EITN OD12 -00 .0- 0A2EITN OD3 EXISTINGLOAD 3 EXISTINGLOAD 3 EXISTINGLOAD 2 EXISTINGLOAD 2 EXISTINGLOAD -- 2 EXISTINGLOAD 2 -- EXISTINGLOAD -- 1 EXISTINGLOAD -- 2 1 -- EXISTINGLOAD 1 A 20 EXISTINGLOAD -- 2 1 EXISTINGLOAD 1 A 20 1 A 20 -- 1 -- A 20 -- A 20 -- -- 2 -- 1 A 20 -- 0.00 1 0.00 A 20 -- 1 A 20 -- 0.00 1 A 20 -- 0.00 0.00 1 0.00 A 20 -- A 20 -- 0.00 -- 0.00 0.00 4.20 -- 0.00 0.00 -- 0.00 -- 0.00 -- 0.00 0.00 -- -- 0.00 0.00 4.20 -- 0.00 -- 0.00 0.00 -- 0.00 0.00 0.00 -- A 20 0.00 -- A 20 1 -- A 20 0.00 1 0.00 -- A 20 1 -- A 20 1 -- A 20 0.00 1 0.00 -- A 20 1 -- A 20 1 -- A 20 1 -- A 20 1 SpaceA 20 41 1 EXISTINGLOAD A 20 39 1 EXISTINGLOAD A 20 37 1 EXISTINGLOAD A 20 35 1 EXISTINGLOAD A 20 33 1 EXISTINGLOAD 31 1 EXISTINGLOAD 29 EXISTINGLOAD 27 EXISTINGLOAD 25 EXISTINGLOAD 23 EXISTINGLOAD 21 EXISTINGLOAD 19 EXISTINGLOAD 17 EXISTINGLOAD 15 EXISTINGLOAD 13 EXISTINGLOAD 11 Space 41 Space 39 Space 37 Space 35 XSIGLA 0A- .000 -2 1 1 A 20 A 20 -- -- 0.00 0.00 0.00 0.00 -- -- A 20 A 20 1 1 Spare 5 EXISTINGLOAD 3 EXISTINGLOAD 1 XSIGLA 0A- .000 -2 XSIGLA 10 EXISTINGLOAD 8 EXISTINGLOAD 6 EXISTINGLOAD 4 EXISTINGLOAD 2 EXISTINGLOAD 1 1 A 20 1 A 20 1 A 20 1 A 20 A 20 ------0.00 -- 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -- -- 0.00 84.00 ------A 20 A 20 1 A 20 1 A 20 1 A 20 1 1 EXISTINGLOAD 9 EXISTINGLOAD 7 EXISTINGLOAD 5 EXISTINGLOAD 3 EXISTINGLOAD 1 ------Total Load (KVA) Other Load (KVA) Motor Load (KVA) Heating Load (KVA) Receptacle Load (KVA) Lighting Load (KVA) Sub-Total in KVA: Enclosu... Feed From: Voltage: SPD: Panel Name: k odNm oeFaeTi rp. ai fDsg Ligh Basis of Design Trip... Trip Frame Pole Load Name Ckt 16 15 14 13 12 11 10 AE D 0 0 LI LI LSI A 200 LI A 200 A 200 A 600 A 200 A 200 A 600 3 A 200 3 3 3 PANEL"D" MAINDISC P4 9 8 P3 7 6 5 4 3 2 1 120/208Wye No PANEL"SERVER" 120/208Wye No P2 120/208Wye YesNo MDP once V eadFco Demand KVA Demand Factor Connected KVA Demand KVA Demand Factor Connected KVA once V eadFco eadKaTi yeTrip U Trip Type Demand Kva Demand Factor Connected KVA 92.40 0.00 5142 SGMoldedCase Electronic with Trip (LUnit MoldedCase Electronicwith Trip Unit (LI) LSIG LI 70 26 15 93 104 76 75 25 19 0 S MoldedCase Electronicwith Trip Unit (LSI) Molded CaseFixedwith Trip Unit LSI 6 3 9 80 100 100 7 3 9 an Mounting: A m p : Main: New/Exi... -- -00 .0------0.00 0.00 ------00 .0------0.00 0.00 ------0.00 0.00 -- 0.00 0.00 0.00 0.00 0.00 0.00 ------00 .0------0.00 -- 0.00 -- 0.00 0.00 -- -- 0.00 0.00 -- -- 0.00 0.00 ------0A- .000 ------2 A 30 -- -- 0.00 0.00 0.00 0.00 -- -- A 30 A 30 1 1 0A- .000 -- -- 8,1... EXISTINGLOAD ------3 0.00 0.00 A 50 0.00 0.00 ------A 50 3 A 20 0.00 0.00 2 -- A 30 2 0A- .000 -2 XSIGLA 6 EXISTINGLOAD 1 A 20 -- 0.00 0.00 -- A 20 1 Enclosure: A m p : Main: New/Exist: Enclosure: A m p : Main: New/Exist: Type1 1000 A 1000 Exist New NEC NEC Type Type Type1 A 200 MCB EX IST Type1 A 200 MCB EX IST SWITCHBOARDSCHEDULE od. KA KA KA Load... C (KVA) B (KVA) A (KVA) Load... od. KA KA KA Load... C (KVA) B (KVA) A (KVA) Load... Feeder: Kaic... Location: PANELBOARD SCHEDULE PANELBOARD SCHEDULE 40 V . V 4.2 kVA 4.2 kVA 84.00 kVA .0kA00kA0.0 kVA 0.0 kVA 0.00 kVA 92.40 0.00 SeeOne Line Surface 65 KAIC 65 ELECTRICAL156 Feeder: Kaic Rating: Mounting: Location: Feeder: Kaic Rating: Mounting: Location: Trip Unit Description Trip Unit Description MoldedCase Electronicwith Trip iUnit (LSI) MoldedCase Electronicwith Trip Unit (LI) Molded CaseFixedwith Trip Unit MoldedCase Electronicwith Trip iUnit (LSI) MoldedCase Electronicwith Trip Unit (LI) Molded CaseFixedwith Trip Unit i ecito Note: nit Description Surface CORRIDOR157 Surface CORRIDOR157 Project Number: Date: Project Name: V 9kA30 A7kA25 kVA 7 kVA 3000 VA 19 kVA 9 kVA 9 kVA 1 kVA 3000 VA 14 kVA 14 VA 3000 kVA 1 kVA 9 sRcpalsHaigPwrMotor Power Heating Receptacles ts SIG) Type Type 18 kVA 7 kVA 11 kVA 11 kVA 7 kVA 18 AppliedEngineering Services (317) 810-4141 0200061.04 6.15.21 MobilitySolutions & Customer CareCenter... Date Project No. Project Name: Date Project No. Project Name: aigPl odNm Ckt Load Name Pole Rating aigPl odNm Ckt Load Name Pole Rating Notes: Notes: AppliedEngineering Services (317) 810-4141 6.15.21 0200061.04 MobilitySolutions & Customer Care Center Facility AppliedEngineering Services (317) 810-4141 6.15.21 0200061.04 MobilitySolutions & Customer Care Center Facility 0 kVA 0 pc 34 Space pc 42 Space 42 Space 40 Space 38 Space 36 Space 28 Space 24 Space pc 40 Space 32 Space 30 Space 26 Space pr 20,... Spare 14 Spare pr 4 Spare 2 Spare ------6,... 2,... 2,... 8 6 0 8 6 0 8 6 4 2 dedm12021-07- 2021-07- Addendum1 1 Addendum2 2 #DSRPINDANB DATE ISSUED DRAWN BY DESCRIPTION # intended Eticaby Group, The Inc. thisuse of tha than for other document any purpose disclaims all implied or warranties, ,express rela from misuse thisof document. Etica Group, The Inc inc. anyinjury isresponsible damage not re for or constitutes impermissible an Etica misuse. The gro other purposethatthan intended Eticaby Group The Group, Inc. is prohibited. Use thisof fodocument theof withoutdocument permissionEtica from The Group, Inc., its assigns.heirs, and Modification Group, Inc. It is solely intended for use by The constructionThis document isE propertythe The of 6.15.21 DATE ISSUED: BID DOCUMENTS BID E601 SCHEDULES ELECTRICAL REVISION SCHEDULE REVISION PROFESSIONAL SEAL: 6/15/21 PROJECT NUMBER: SHEET NUMBER:SHEET DRAWING TITLE: 0200061.04 DISCLAIMER: DRAWN BY:DRAWN Mobility Solutions & Customer Care Center Facility DAG 2425 W. Michigan St., Indianapolis, IN 46222 Indianapolis Public Transportation Corporation CHECKED BY: 06 08 Etica or reuse reuse or ting toting the LDH sulting r any r up, up, tica tica t . 1501 W. Washington Street , Inc. Indianapolis, IN 46204