70300 Ethyl Acetate

Total Page：16

File Type：pdf, Size：1020Kb

70300 Ethyl Acetate Colorless, clear, aromatic liquid with agreeable smell. Ethyl acetate is readily soluble in alcohol, ether, chloroform, fatty oils and essential oils. Ethyl acetate is soluble in 12 times the amount of water, in which it slowly decomposes under the influence of light and air to alcohol and acetic acid. Therefore the solution slowly turns acid. Ethyl acetate is a good solvent for cellulose nitrate, celluloid, oils, chlorinated rubber, colophonium, gum copal, vinyl resins, ect. Application Ethyl acetate is used as a component of artificial apple, pear, strawberry, raspberry and black current ether; to give aroma to sweets, fruit juices, liqueurs, lemonades, as solvent for collodium cotton, nitro cotton, celluloid, etc., and in the preparation of caffeine-free coffee. Formula: CH 3CO 2CH 2CH 3 Hazard symbol: F = flammable Synonym(s): Acetic acid ethyl ester Description: Colorless liquid with characteristic aromatic odor MAK-Value: 400 ppm Properties Highly volatile, flammable liquid with combustible fumes (heavier than air). Combustion can be caused by hot surfaces, sparks and naked flames. Health hazard At high concentrations the fumes can cause narcotic effects. Due to its high vapor pressure, a hazardous concentration level is quickly reached. The fumes irritate skin and mucous membranes. Skin contact with product can cause skin irritations due its strong degreasing effect. Comments Not miscible with water, floats on water surface. A large amount of ethyl acetate is hazardous to all water systems (M). Store in tightly closed containers since ethyl acid is hygroscopic. Contact with water and especially bases decomposes product in acetic acid and ethyl alcohol. Ethyl acetate complies to the RoHS Directive 2011/65/EU of the European Union. Page 1 of 1 Kremer Pigmente GmbH & Co. KG · Hauptstr. 41-47 · DE-88317 Aichstetten ·Tel. 0049 7565 914480 · [email protected]· www.kremer-pigmente.com We do not assume any warranty for the guidance shown above. In any case, we recommend production and evaluation of samples. .

Copy Link

Recommended publications

Solvent Fractionation and Acetone Precipitation for Crude Saponins from Eurycoma Longifolia Extract
molecules Article Solvent Fractionation and Acetone Precipitation for Crude Saponins from Eurycoma longifolia Extract Lee Suan Chua 1,2,* , Cher Haan Lau 1, Chee Yung Chew 2 and Dawood Ali Salim Dawood 1 1 Metabolites Proﬁling Laboratory, Institute of Bioproduct Development, Universiti Teknologi Malaysia, Skudai, Johor Bahru 81310 UTM, Johor, Malaysia; [email protected] (C.H.L.); [email protected] (D.A.S.D.) 2 Department of Bioprocess and Polymer Engineering, School of Chemical and Energy Engineering, Faculty of Engineering, Universiti Teknologi Malaysia, Skudai, Johor Bahru 81310 UTM, Johor, Malaysia; [email protected] * Correspondence: [email protected]; Tel.: +607-5531566 Academic Editors: Raffaele Capasso and Lorenzo Di Cesare Mannelli Received: 22 March 2019; Accepted: 2 April 2019; Published: 10 April 2019 Abstract: Eurycoma longifolia is a popular folk medicine in South East Asia. This study was focused on saccharide-containing compounds including saponins, mainly because of their medical potentials. Different organic solvents such as ethyl acetate, butanol, and chloroform were used to fractionate the phytochemical groups, which were consequently precipitated in cold acetone. Solvent fractionation was found to increase the total saponin content based on colorimetric assay using vanillin and sulfuric acid. Ethyl acetate fraction and its precipitate were showed to have the highest crude saponins after acetone precipitation. The samples were shown to have anti-proliferative activity comparable with tamoxifen (IC50 = 110.6 µg/mL) against human breast cancer cells. The anti-proliferative activities of the samples were signiﬁcantly improved from crude extract (IC50 = 616.3 µg/mL) to ethyl acetate fraction (IC50 = 185.4 µg/mL) and its precipitate (IC50 = 153.4 µg/mL).
[Show full text]
Fermentation and Ester Taints
Fermentation and Ester Taints Anita Oberholster Introduction: Aroma Compounds • Grape‐derived –provide varietal distinction • Yeast and fermentation‐derived – Esters – Higher alcohols – Carbonyls – Volatile acids – Volatile phenols – Sulfur compounds What is and Esters? • Volatile molecule • Characteristic fruity and floral aromas • Esters are formed when an alcohol and acid react with each other • Few esters formed in grapes • Esters in wine ‐ two origins: – Enzymatic esterification during fermentation – Chemical esterification during long‐term storage Ester Formation • Esters can by formed enzymatically by both the plant and microbes • Microbes – Yeast (Non‐Saccharomyces and Saccharomyces yeast) – Lactic acid bacteria – Acetic acid bacteria • But mainly produced by yeast (through lipid and acetyl‐CoA metabolism) Ester Formation Alcohol function Keto acid‐Coenzyme A Ester Ester Classes • Two main groups – Ethyl esters – Acetate esters • Ethyl esters = EtOH + acid • Acetate esters = acetate (derivative of acetic acid) + EtOH or complex alcohol from amino acid metabolism Ester Classes • Acetate esters – Ethyl acetate (solvent‐like aroma) – Isoamyl acetate (banana aroma) – Isobutyl acetate (fruit aroma) – Phenyl ethyl acetate (roses, honey) • Ethyl esters – Ethyl hexanoate (aniseed, apple‐like) – Ethyl octanoate (sour apple aroma) Acetate Ester Formation • 2 Main factors influence acetate ester formation – Concentration of two substrates acetyl‐CoA and fusel alcohol – Activity of enzyme responsible for formation and break down reactions • Enzyme activity influenced by fermentation variables – Yeast – Composition of fermentation medium – Fermentation conditions Acetate/Ethyl Ester Formation – Fermentation composition and conditions • Total sugar content and optimal N2 amount pos. influence • Amount of unsaturated fatty acids and O2 neg. influence • Ethyl ester formation – 1 Main factor • Conc. of precursors – Enzyme activity smaller role • Higher fermentation temp formation • C and N increase small effect Saerens et al.
[Show full text]
Isoamyl Acetate
SUMMARY OF DATA FOR CHEMICAL SELECTION Isoamyl Acetate CAS No. 123-92-2 Prepared for NTP by Technical Resources International, Inc Prepared on 11/94 Under NCI Contract No. N01-CP-56019 Table of Contents I. Chemical Identification II. Exposure Information Table 1. Levels of isoamyl acetate reported in foods III. Evidence for Possible Carcinogenic Activity Appendix A: Structural Analogs of Isoamyl Acetate IV. References SUMMARY OF DATA FOR CHEMICAL SELECTION CHEMICAL IDENTIFICATION CAS Registry No.: 123-92-2 Chem. Abstr. Name: 1-Butanol, 3-methyl-, acetate Synonyms: Acetic acid 3-methylbutyl ester; acetic acid, isopentyl ester; AI3-00576; banana oil; isoamyl ethanoate; isopentyl acetate; isopentyl alcohol, acetate; pear oil; 3-methyl-1-butanol acetate; 3-methyl-1-butyl acetate; 3-methylbutyl acetate; 3-methylbutyl ethanoate; i-amyl acetate Structure: Molecular Formula and Molecular Weight: C7H14O2 Mol. Wt.: 130.18 Chemical and Physical Properties: Description: Colorless, flammable liquid with a banana-like odor (ACGIH, 1993). Boiling Point: 142°C (Lide, 1993) Melting Point: -78.5°C (Mark, et al, 1984; Lide, 1993) Solubility: Soluble in water (2000 mg/L at 25°C) (Howard, 1990); soluble in ethanol, diethyl ether, and acetone (Lide, 1993). Vapor 4.5 mm Hg at 20°C (Howard, 1990) Pressure: Refractive 1.4003 (Lide, 1993) Index: Flash Point: closed cup, 33°C; open cup, 38°:C (Budavari, 1989) Density: 0.876 (Lewis, 1993) Reactivity: Thermal decomposition of isoamyl acetate may produce acrid fumes. Contact with strong oxidizing agents, strong acids, and alkaline materials should be avoided (Haarmann & Reimer Corp., 1994). Hazardous decomposition products of isoamyl acetate include CO and CO2 (AESAR/Alfa, 1994) Log 2.13 (Howard, 1990) P(octanol/water partition coefficient): Technical Isoamyl acetate is commercially available as both a natural and synthetic product with a purity Products and range of 95-99+%.
[Show full text]
Dehydrogenation of Ethanol to Acetaldehyde Over Different Metals Supported on Carbon Catalysts
catalysts Article Dehydrogenation of Ethanol to Acetaldehyde over Different Metals Supported on Carbon Catalysts Jeerati Ob-eye , Piyasan Praserthdam and Bunjerd Jongsomjit * Center of Excellence on Catalysis and Catalytic Reaction Engineering, Department of Chemical Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok 10330, Thailand; [email protected] (J.O.-e.); [email protected] (P.P.) * Correspondence: [email protected]; Tel.: +66-2-218-6874 Received: 29 November 2018; Accepted: 27 December 2018; Published: 9 January 2019 Abstract: Recently, the interest in ethanol production from renewable natural sources in Thailand has been receiving much attention as an alternative form of energy. The low-cost accessibility of ethanol has been seen as an interesting topic, leading to the extensive study of the formation of distinct chemicals, such as ethylene, diethyl ether, acetaldehyde, and ethyl acetate, starting from ethanol as a raw material. In this paper, ethanol dehydrogenation to acetaldehyde in a one-step reaction was investigated by using commercial activated carbon with four different metal-doped catalysts. The reaction was conducted in a packed-bed micro-tubular reactor under a temperature range of 250–400 ◦C. The best results were found by using the copper doped on an activated carbon catalyst. Under this speciﬁed condition, ethanol conversion of 65.3% with acetaldehyde selectivity of 96.3% at 350 ◦C was achieved. This was probably due to the optimal acidity of copper doped on the activated carbon catalyst, as proven by the temperature-programmed desorption of ammonia (NH3-TPD). In addition, the other three catalyst samples (activated carbon, ceria, and cobalt doped on activated carbon) also favored high selectivity to acetaldehyde (>90%).
[Show full text]
Hydrogenation of Ethyl Acetate to Ethanol Over Ni-Based Catalysts Obtained from Ni/Al Hydrotalcite-Like Compounds
Molecules 2010 , 15 , 5139-5152; doi:10.3390/molecules15085139 OPEN ACCESS molecules ISSN 1420-3049 www.mdpi.com/journal/molecules Article Hydrogenation of Ethyl Acetate to Ethanol over Ni-Based Catalysts Obtained from Ni/Al Hydrotalcite-Like Compounds Beixiao Zhang, Lu Lin *, Junping Zhuang, Ying Liu *, Lincai Peng and Longfei Jiang State Key Laboratory of Pulp and Paper Engineering, South China University of Technology, Guangzhou 510640, Guangdong, China * Author to whom correspondence should be addressed; E-Mails: [email protected] (L.L.); [email protected] (Y.L.). Received: 18 June 2010; in revised form: 17 July 2010 / Accepted: 23 July 2010 / Published: 29 July 2010 Abstract: A series of Ni-based catalysts were prepared using hydrogen reduction of Ni/Al hydrotalcite-like compounds (Ni/Al HTlcs) synthesized by coprecipitation. The physico- chemical properties of Ni/Al hydrotalcite-like compounds and the corresponding Ni-based catalysts were characterized using inductively coupled plasma (ICP), BET surface areas, X- ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) techniques. The results indicated that Ni/Al HTlcs with layered structures could be successfully prepared by the coprecipitation method, and the characteristic HTlcs reflections were also observed in the XRD analysis. The NiO and Ni 0 phases were identified in all Ni-based catalysts, which displayed randomly interconnected pores and no layer structures. In addition, the studies also found the Ni/Al HTlcs and Ni- based catalysts had high specific surface areas, low pore volumes and low pore diameters. The catalytic hydrogenation of ethyl acetate to ethanol with Ni-based catalysts was also investigated.
[Show full text]
NMR Chemical Shifts of Common Laboratory Solvents As Trace Impurities
7512 J. Org. Chem. 1997, 62, 7512-7515 NMR Chemical Shifts of Common Laboratory Solvents as Trace Impurities Hugo E. Gottlieb,* Vadim Kotlyar, and Abraham Nudelman* Department of Chemistry, Bar-Ilan University, Ramat-Gan 52900, Israel Received June 27, 1997 In the course of the routine use of NMR as an aid for organic chemistry, a day-to-day problem is the identifica- tion of signals deriving from common contaminants (water, solvents, stabilizers, oils) in less-than-analyti- cally-pure samples. This data may be available in the literature, but the time involved in searching for it may be considerable. Another issue is the concentration dependence of chemical shifts (especially 1H); results obtained two or three decades ago usually refer to much Figure 1. Chemical shift of HDO as a function of tempera- more concentrated samples, and run at lower magnetic ture. fields, than today’s practice. 1 13 We therefore decided to collect H and C chemical dependent (vide infra). Also, any potential hydrogen- shifts of what are, in our experience, the most popular bond acceptor will tend to shift the water signal down- “extra peaks” in a variety of commonly used NMR field; this is particularly true for nonpolar solvents. In solvents, in the hope that this will be of assistance to contrast, in e.g. DMSO the water is already strongly the practicing chemist. hydrogen-bonded to the solvent, and solutes have only a negligible effect on its chemical shift. This is also true Experimental Section for D2O; the chemical shift of the residual HDO is very NMR spectra were taken in a Bruker DPX-300 instrument temperature-dependent (vide infra) but, maybe counter- (300.1 and 75.5 MHz for 1H and 13C, respectively).
[Show full text]
Ester Synthesis Lab (Student Handout)
Name: ________________________ Lab Partner: ____________________ Date: __________________________ Class Period: ____________________ Ester Synthesis Lab (Student Handout) Lab Report Components: The following must be included in your lab book in order to receive full credit. 1. Purpose 2. Hypothesis 3. Procedure 4. Observation/Data Table 5. Results 6. Mechanism (In class) 7. Conclusion Introduction The compounds you will be making are also naturally occurring compounds; the chemical structure of these compounds is already known from other investigations. Esters are organic molecules of the general form: where R1 and R2 are any carbon chain. Esters are unique in that they often have strong, pleasant odors. As such, they are often used in fragrances, and many artificial flavorings are in fact esters. Esters are produced by the reaction between alcohols and carboxylic acids. For example, reacting ethanol with acetic acid to give ethyl acetate is shown below. + → + In the case of ethyl acetate, R1 is a CH3 group and R2 is a CH3CH2 group. Naming esters systematically requires naming the functional groups on both sides of the bridging oxygen. In the example above, the right side of the ester as shown is a CH3CH2 1 group, or ethyl group. The left side is CH3C=O, or acetate. The name of the ester is therefore ethyl acetate. Deriving the names of the side from the carboxylic acid merely requires replacing the suffix –ic with –ate. Materials • Alcohol • Carboxylic Acid o 1 o A o 2 o B o 3 o C o 4 Observation Parameters: • Record the combination of carboxylic acid and alcohol • Observe each reactant • Observe each product Procedure 1.
[Show full text]
Method, Catalyst and Apparatus for Producing Acetaldehyde from Acetic Acid
Patentamt Europaisches ||| || 1 1| || || || ||| || || || ||| ||| || (19) J European Patent Office Office europeen des brevets (11) EP 0 953 560 A1 (12) EUROPEAN PATENT APPLICATION Date of (43) publication: (51) |nt. CI.6: C07C 45/41 , C07C 47/06, 03.11.1999 Bulletin 1999/44 B01J 23/74, B01J 23/76 (21) Application number: 98115520.3 (22) Date of filing: 18.08.1998 (84) Designated Contracting States: • Depew, Leslie S. AT BE CH CY DE DK ES Fl FR GB GR IE IT LI LU Kingsport, TN 37662-5072 (US) MC NL PT SE • Collins, Nick A. Designated Extension States: Kingsport, TN 37662-5072 (US) AL LT LV MK RO SI (74) Representative: (30) Priority: 30.04.1998 US 69953 Winter, Brandl, Furniss, Hubner, Ross, Kaiser, Polte, Kindermann (71) Applicant: Partnerschaft EASTMAN CHEMICAL COMPANY Patent- und Rechtsanwaltskanzlei Kingsport, Tennessee 37662-5075 (US) Alois-Steinecker-Strasse 22 85354 Freising (DE) (72) Inventors: • Tustin, Gerald C. Kingsport, TN 37662-5072 (US) (54) Method, catalyst and apparatus for producing acetaldehyde from acetic acid (57) A method of producing acetaldehyde hydro- genates acetic acid in the presence of an iron oxide cat- alyst containing between 2.5 and 90 wt % Pd, more "p'J. " f3^ preferably 10 and 80 wt % Pd and most preferably 20 ^ i 'V""^ .. ' and 60 wt % Pd. The catalyst has a specific surface XX area of less than 150 m2/g. Hydrogen and acetic acid n * are fed to a reactor in a hydrogen to acetic acid ratio of M£p 2:1 to 25:1 , more preferably in a hydrogen to acetic acid > Mvx, [=3 ratio of 3:1 to 15:1 and most preferably in a hydrogen to eTF acetic acid ratio of 4:1 to 12:1.
[Show full text]
Supporting Information
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry This journal is © The Royal Society of Chemistry 2012 Supporting Information Part 1. Description on materials used in the present work Table S1 Details of the materials used in the experiments Abbreviation Chemicals Grade of materials Manufacturer in the text Trihydroxymethyl TMPTA Not specified Tianjiao chemicals, Tianjin, China propane triacrylate Styrene St Chemical pure Beijing chemicals, Beijing, China Qiuzhu Corp. of science & technology, Anhydrous ethanol EtOH Chemical pure Tianjin, China Azobisisobutyronitrile AIBN Chemical pure Damao chemicals, Tianjin, China Ethyl benzene EB Chemical pure Fuyu chemical Corp., Tianjin, China Cyclohexane, xylene All from Fuyu Chemical Corp., Tianjin, Chemical pure and toluene China Water H2O Double distilled Done in the laboratory Part 2. Description on precipitation polymerization and sample characterization Polymerizations were carried out in glass bottles of 120 mL capacity. In each was charged 2 mL of monomers TMPTA and St at varied mass ratios, along with 2.0 wt% azobisisobutyronitrile (AIBN) relative to the monomers. 98 mL of ternary solvent mixture consisting of distilled H2O, anhydrous EtOH and ethyl benzene (EB) at different volume ratios was then added into each bottle. After complete dissolution of the monomers and the initiator followed by nitrogen purge for 5 min, all bottles were sealed off and located into a thermostat, whose temperature was increased to 70 °C within 1 h. The initially homogeneous reaction mixtures turned milky white within 5 to 10 min after reaching 70 °C, depending on the formulation. Unless otherwise stated, all reactions were run for 4 h. In some parallel runs, EB was replaced by a same volume of an alternative solvent, including cyclohexane, xylene, toluene, ethyl benzene, acetone, acetonitrile, ethyl acetate, butanone, octanol and trichlormethane, 10 solvent in total.
[Show full text]
Ketones Acetone, MEK, MIBK, DIBK, and DAA
KETONES Acetone, MEK, MIBK, DIBK, and DAA Shell Chemicals 2 KETONES ARE STRONG POLAR SOLVENTS AND ARE USed IN A VARIETY OF APPLICATIONS INCLUDING: ■■ Paints and coatings (major end use) ■■ Adhesives ■■ Magnetic tape ■■ Inks ■■ Cleaning ■■ Aerospace ■■ Extraction Ketones IF YOU WANT TO KNOW WHERE WE CAN Take YOU, LOOK AT WHERE WE’VE beeN From the beginning, Shell chemical companies products. We are committed to being leading- have built a reputation for a broad product edge suppliers in today’s global marketplace. range, technical expertise and manufacturing excellence. We are one of the largest Although Shell Chemicals have continued to petrochemical concerns in the world with develop new solvent alternatives, we have manufacturing facilities in 13 countries and maintained our commitment to our core solvent marketing hubs in 3 global regions with products, including hydrocarbon solvents, customer service covering 55 countries. alcohols, glycol ethers and ketone solvents. Shell pioneered the use of ketone solvents, has We draw on more than 80 years of manufacturing sites in Europe, and is a major experience in the solvents business and global supplier. Shell maintains an excellent provide assistance to customers regarding global supply position to satisfy anticipated solvent selection, solvent regulations and demand for the ketone family of solvents. general HSSE support. It is this commitment Figure 1 gives the typical properties for the and customer focus that allow us to remain an ketones available from Shell Chemicals, industry leader. including acetone, methyl ethyl ketone (MEK), methyl isobutyl ketone (MIBK), di-isobutyl We have been producing solvents for ketone (DIBK) and diacetone alcohol (DAA).
[Show full text]
Liquid-Liquid Equilibrium for the Ternary Systems of Solvents+Water+Propionic Acid at 25 Oc and Atmospheric Pressure
Korean J. Chem. Eng., 22(2), 256-263 (2005) Liquid-Liquid Equilibrium for the Ternary Systems of Solvents+Water+Propionic Acid at 25 oC and Atmospheric Pressure Jae-Kyung Kim and Dong-Won Park† Department of Chemical Engineering, Dong-A University, Hadan2-dong, Saha-gu, Busan 604-714, South Korea (Received 27 September 2004 • accepted 10 January 2005) Abstract−Liquid-liquid equilibrium data for the ternary systems of toluene+water+propionic acid, o-xylene+water +propionic acid, methyl isobutyl ketone+water+propionic acid, ethyl acetate+water+propionic acid, and 1-butanol +water+propionic acid were measured at 25 oC and atmospheric pressure. The reliability of the experimental tie-line data was ascertained by means of the Othmer-Tobias, Bachman-Brown, and Hand correlations. For the extraction effec- tiveness of solvents, the distribution and selectivity curves were plotted. In addition, these experimental tie-line data were also correlated with NRTL and UNIQUAC models. Key words: Liquid-Liquid Equilibrium, Ternary, NRTL, UNIQUAC, Propionic Acid INTRODUCTION Toluene, o-xylene, methyl isobutyl ketone, ethyl acetate, 1-butanol and propionic acid used in this work were supplied by Aldrich with With an increase in demand for environmentally friendly mate- a started purity of over 99.0%, and ordinary bidistilled water was rial, the recovery of organic acids from dilute solutions resulting used. The purity of each of the components was checked by gas from fermentation processes has become of interest. Economics of chromatography. The GC analysis did not show any appreciable the process, however, depends on the development of an effective peaks of impurities for all the components and determined >99.0 recovery method for the organic acids from the broth [Roychoudhury mass fraction purities for toluene, o-xylene, methyl isobutyl ketone, et al., 1995].
[Show full text]
Ethyl Acetate
Common Name: ETHYL ACETATE CAS Number: 141-78-6 RTK Substance number: 0841 DOT Number: UN 1173 Date: June 1996 Revision: July 2002 ------------------------------------------------------------------------- ------------------------------------------------------------------------- HAZARD SUMMARY WORKPLACE EXPOSURE LIMITS * Ethyl Acetate can affect you when breathed in and by OSHA: The legal airborne permissible exposure limit passing through your skin. (PEL) is 400 ppm averaged over an 8-hour * Ethyl Acetate can irritate the skin, eyes, nose and throat. workshift. * Exposure to high levels can cause you to feel dizzy, lightheaded, and to pass out. NIOSH: The recommended airborne exposure limit is * Repeated contact can cause drying and cracking of the 400 ppm averaged over a 10-hour workshift. skin. * Long-term exposure can affect the liver and kidneys. ACGIH: The recommended airborne exposure limit is * Ethyl Acetate is a FLAMMABLE LIQUID and a FIRE 400 ppm averaged over an 8-hour workshift. HAZARD. * The above exposure limits are for air levels only. When IDENTIFICATION skin contact also occurs, you may be overexposed, even though air levels are less than the limits listed above. Ethyl Acetate is a colorless liquid with a fragrant, fruity odor. It is used as a solvent, a synthetic flavoring substance, and in making perfumes and dyes. WAYS OF REDUCING EXPOSURE * Where possible, enclose operations and use local exhaust REASON FOR CITATION ventilation at the site of chemical release. If local exhaust * Ethyl Acetate is on the Hazardous Substance List because ventilation or enclosure is not used, respirators should be it is regulated by OSHA and cited by ACGIH, DOT, worn. NIOSH, HHAG, NFPA and EPA. * Wear protective work clothing.
[Show full text]