DOCSLIB.ORG

HP Indigo Ink Information

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
HP Indigo Ink Information hp indigo digital printing hp ElectroInk Frequently Asked Questions what is hp ElectroInk® ? do images printed with hp ElectroInk have any degradation of color values? hp ElectroInk is a unique liquid ink that combines the advantages of electronic printing with the qualities of liquid Images printed with hp ElectroInk were analyzed after a ink. hp ElectroInk contains charged pigmented particles in print run of 100,000 impressions, and measured for a a liquid carrier, and enables digital printing by electrically change in color. The analysis found no degradation in color controlling the location of these particles. values of the xth print compared to the 1st print (∆E*< 2)2. how does hp ElectroInk support the performance does hp ElectroInk that has been stored for a period required for high quality, digital color printing? of time have any degradation of color values? The small particle size in the liquid carrier enables high The hp ElectroInk was analyzed after one year of storage resolution, uniform gloss, sharp image edges, and very and measured for a change in color. The analysis found no thin image layers which closely follow the surface degradation in color values (∆E*< 3). topography of the paper resulting in a highly uniform finish. what is hp ElectroInk’s ability to withstand exposure to light? what is hp ElectroInk’s resistance to abrasion? hp ElectroInk’s ability to withstand exposure to light is hp ElectroInk’s resistance to abrasion is characterized by measured by utilizing a test for Light-Fastness. utilizing a test procedure for rub-resistance that measures The lightfastness test measures the print’s resistance to the ink’s adhesion to the substrate. ultraviolet light by measuring the change that occurred between the exposed area to the unexposed area. HP Indigo labs utilize two types of measurements that Two separate tests of lightfastness are shown below. characterize rub resistance: The first shows results based on a blue wool reference 1. Sutherland abrasion resistance - A standard scale, while the second shows results based on percentage measurement that provides guidelines of fading (optical density) and deltaE* (color coordinate 2. GaCat abrasion resistance - A standard measurement changes). that provides guidelines and a semi-quantitative scale. lightfastness test 1: Blue Wool sutherland measurement results: The light fastness test was done using a Xenon UV Lamp No significant difference in abrasion resistance of 100% according to the British Standard BS 1006B02 for indoor solids vs. close to 100% halftone gray images was found. conditions and ISO1134M1 method for outdoor conditions gacat measurement1 results: The result is on a 1-8 blue wool reference scale. hp ElectroInk performs better than grade 3 1Completely faded 0 No damage 8 No fading 10 Completely damaged 2 DeltaE* expresses the color change between the X print to the 1st. print at the same Optical density. The optimal result is when DeltaE* is close to zero. 1 The conditions of measurements were as follows: 100% solids test image,receptor C5, frequency 2 sec-1, 120 sec. please note that specific papers/substrates may give deviations from the presented test results. indoor test ISO1006B02 hp ElectroInk 3.1 Offset Ink Cyan Yellow Magenta Black Cyan Yellow Magenta Black Paper (untreated) 5-7 4-5 5 5 6-7 2-3 1 4 PVC (treated) 6-7 4-6 5-7 4-5 PET (treated) 6-7 1-2 5-7 3-4 outdoor test ISO11341M1 PVC (treated) 6-7 4-6 5-6 3-6 PET (treated) 6-7 1-2 3-4 3-4 indoor test ISO105B02 hp ElectroInk 3.2 Offset Ink Cyan Yellow Magenta Black Cyan Yellow Magenta Black Paper (untreated) 76 6 3-46-72-31 4 Blue Wool Scale [BWS] scale Days indoors comments 13.75Very poor 1 2 26 poor 319fair 465moderate 5130 good 3 4 6260 Very good 7520excellent 8 1100 outstanding 5 6 The blue wool scale is composed of 8 strips of wool fabric, of different standard dyeing. Their chromatic grade goes from the Standard 1, with very scarce light fastness, to the Standard 8 with very elevated light fastness. Every standard is twice more solid than the preceding one. 7 8 example of a blue wool scale lightfastness test 2: Optical density & Color Coordinates Paper type Simulated by testing on This lightfastness test was done by exposing test samples for 3-day cycles while monitoring changes in optical SBR coated Gloss Condat Gloss density (%fading) and color coordinates (deltaE*). SBR coated Matte Condat Matte Each 3-day cycle simulates 6 years exposure under the above conditions. Three cycles of six days each, simulates Acrylic coated BVS eighteen years. The tests were done using ElectroInks and Uncoated Carnival Offset inks on various types of paper, intended to simulate a variety of typical substrates. deltaE %fading 10.00 20.00 30.00 40.00 60.00 50.00 15.00 35.00 45.00 25.00 55.00 0.00 5.00 -10 10 15 20 30 40 60 50 35 45 25 65 55 -5 lightfastness test2: equivalent) (6years exposure change at3days incolorcoordinates 0 5 lightfastness test 2: change in Optical Density at 3 days exposure (6 years equivalent) (6years lightfastness test2: change exposure inOptical Density at3days SBR Gloss SBR Gloss YM C YM C SBR Matte SBR Matte Acrylic Acrylic coated coated Uncoated Uncoated SBR Gloss SBR Gloss SBR Matte SBR Matte Acrylic Acrylic coated coated paper types Uncoated paper types Uncoated SBR Gloss SBR Gloss SBR Matte SBR Matte Acrylic Acrylic coated coated Uncoated Uncoated SBR Gloss SBR Gloss SBR Matte SBR Matte K K Acrylic Acrylic E1 offset coated coated E1 offset Uncoated Uncoated how resistant to heat are substrates printed with hp ElectroInks? The test for heat resistance measures the changes in color coordinates and optical density of a printed material which is exposed to heat. Heat resistance was tested by exposing various printed substrates at a temperature of 120° for 30 minutes. heat resistance test: change in optical density 6.5 6 5.5 5 4.5 4 3.5 3 % fading 2.5 2 offset 1.5 EI3.1 1 EI3.2 -0.5 0 SBR coated SBR coated Acrylic coated Uncoated Gloss Matte paper type heat resistance test: change in color coordinates 3.6 3.3 3.0 2.7 2.4 2.1 1.8 Delta E* 1.5 1.2 offset 0.9 EI3.1 0.6 EI3.2 0.3 0 SBR coated SBR coated Acrylic coated Uncoated Gloss Matte paper type may hp ElectroInk be used for printing food may hp ElectroInk be used for printing food packaging applications in the United States? packaging applications in the European Union? Certain hp ElectroInk products, which are listed in the table Certain hp ElectroInk products, which are listed in the table below, are compliant with FDA requirements for printing on below, are compliant with requirements for printing on the the non-food contact side of food packaging of an non-food contact side of food packaging of an appropriate appropriate multiplayer food packaging material. multiplayer food packaging material under the German The material used for the food packaging in conjunction and European food legislation (German Bundesinstitut fur with the approved hp ElectroInk must be comprised of one gesundheitlichen Verbraucherschutz und Veterinarmedizin of the following materials: (1) low density polyethylene (BgVV) and European Union (EU). The material used for the (LDPE) that is at least 40 microns thick; (2) polypropylene food packaging in conjunction with the approved that is at least 20 microns thick; (3) polyester which is at hp ElectroInk must be Series 1 inks least 12 microns thick. The resulting packages may be comprised of one of the used to hold all types of food at temperatures up to 100 following materials: Mark 3.1 Cyan deg C (also known as US FDA's Condition of Use B, (1) low density polyethylene Mark 3.1 Magenta "Boiling Water Sterilized", under 21 CFR 176.170). (LDPE) that is at least 40 microns thick; Mark 3.1 Yellow Series 1 inks (2) polypropylene that Series 2 inks Mark 3.1 Black is at least 20 microns thick; Mark 3.1 Cyan Mark 3.2 Cyan (3) polyester which is at least Orange 003 Mark 3.1 Magenta 12 microns thick. Mark 3.2 Magenta Green 011 The resulting packages may Mark 3.1 Yellow Mark 3.2 Yellow be used to hold all types of Blue 013 Mark 3.1 Black food at temperatures up to Mark 3.2 Black Violet 065 100 deg C. Orange 003 Orange 070 We are investigating the Red 006 Green 011 status of series 2 inks and Green 072 Transparent 025 expect to have the data Blue 013 Violet 071 available by spring 2003. Violet 065 are any additional products recommended to Red 006 enhance the adhesion of hp ElectroInk to the plastic Transparent 025 substrates typically used in food packaging? White We recommend the use of a product called Topaz, which is distributed by HP Indigo, and is utilized in coating plastic substrates to enhance their compatibility with hp ElectroInk ink. can substrates treated with Topaz be used for printing on food-packaging applications? In the U.S., substrates treated with Topaz can be used for printing on the non-food-contact-side of food packaging when they are composed of any of the following materials: (1) low-density polyethylene (LDPE) that is at least 40 microns thick; (2) polypropylene that is at least 20 microns thick; or (3) polyester which is at least 12 microns thick. The alcohol solvent evaporates after application, leaving the Topaz as a dry layer.
Load more

Recommended publications
  • Solvent-Based Screen
    Technical Data Sheet Nazdar 9600 Series Polyester Screen Ink v 12 EN 9600 Series Screen Ink is designed primarily for printing on untreated polyester films. The ink dries to a film exhibiting good gloss and flexibility with the exception of 9652 Super Opaque Ref: v 11 EN Black, which exhibits a matte, but flexible ink film. 9600 Series may be catalyzed with NB72 Catalyst or NB80 Adhesion Promoter for adhesion to a diverse range of substrates including polyester, some rubber, polycarbonate, melamine plastics, leather and some coated and uncoated metals. When printing 9600 Series on polycarbonate for insert‐mold decorating applications, up to 5% by weight addition of NB72 provides optimum performance. Substrates Maintain ink temperature at 65°‐90°F (18°‐32°C) for optimum print and cure performance. Lower Untreated polyester temperatures increase the ink viscosity, impairing Polyester coated surfaces flow and increasing film thickness. Elevated Some treated or top coated polyester temperatures lower the ink viscosity, reducing films print definition and film thickness. Polycarbonate Substrate recommendations are based on commonly available Pretest to determine optimum printing materials intended for the ink’s specific market when the inks parameters for a particular set of ink, substrate, are processed according to this technical data. While technical screen, press, and curing variables/conditions. information and advice on the use of this product is provided in good faith, the User bears sole responsibility for selecting Nazdar does not recommend inter‐mixing of 9600 Ink the appropriate product for their end‐use requirements. Series with other inks besides the 9600 Series. Reference the ‘Quality Statement’ at the end of this document.
    [Show full text]
  • Conventional Screen Ink Color Chart
    Conventional Screen Ink Color Chart 2700 Series, 5100 Series, 6100 Series, 7200 Series, 7700 Series, 7900 Series, 8400 Series, 8800 Series, 8900 Series, 9600 Series, 9700 Series, 9800 Series, ADE Series, PP Series, S2 Series. The Conventional Screen Inks Color Chart is representative of the colors available in several Nazdar Conventional ink series; however, some colors are not available in all ink series. Check the specific product pages for specific ink series color availability. PANTONE® Base Colors 2700 Series, 5100 Series, 6100 Series, 7200 Series, 7700 Series, 7900 Series, 8400 Series, 8800 Series, 8900 Series, 9600 Series, 9700 Series, 9800 Series, ADE Series, PP Series, S2 Series. conventiaonl The Conventional Screen Inks Color Chart is representative of the colors available in several Nazdar Conventional ink series; however, some colors are not available in all ink series. Check the specific product pages for specific ink series color availability. 60/360 61/361 62/362 63/363 64/364 65/365 Orange Yellow Warm Red Rubine Red Rhodamine Red Purple * PANTONE 165C * PANTONE 102C * PANTONE Warm Red C * PANTONE Rubine Red C * PANTONE Rhodamine Red C * PANTONE 2593C 66/366 67/367 68/368 69/369 Violet Reflex Blue Process Blue Green * PANTONE 2747C * PANTONE Reflex Blue C * PANTONE 3015 C * PANTONE Green C conventiaonl Color charts represented on Nazdar.com are provided to give printers a general idea of the colors available in Nazdar ink lines. Due to the wide variations and inconsistencies 10 in Primrose computer monitors and11 digitalLemon color palettes,12 the Medium colors seen here are 19only Fire approximations of20 actual Brilliant ink colors.
    [Show full text]
  • Color Gamut of Halftone Reproduction*
    Color Gamut of Halftone Reproduction* Stefan Gustavson†‡ Department of Electrical Engineering, Linkøping University, S-581 83 Linkøping, Sweden Abstract tern then gets attenuated once more by the pattern of ink that resides on the surface, and the finally reflected light Color mixing by a halftoning process, as used for color is the result of these three effects combined: transmis- reproduction in graphic arts and most forms of digital sion through the ink film, diffused reflection from the hardcopy, is neither additive nor subtractive. Halftone substrate, and transmission through the ink film again. color reproduction with a given set of primary colors is The left-hand side of Fig. 2 shows an exploded view of heavily influenced not only by the colorimetric proper- the ink layer and the substrate, with the diffused reflected ties of the full-tone primaries, but also by effects such pattern shown on the substrate. The final viewed image as optical and physical dot gain and the halftone geom- is a view from the top of these two layers, as shown to etry. We demonstrate that such effects not only distort the right in Fig. 2. The dots do not really increase in the transfer characteristics of the process, but also have size, but they have a shadow around the edge that makes an impact on the size of the color gamut. In particular, a them appear larger, and the image is darker than what large dot gain, which is commonly regarded as an un- would have been the case without optical dot gain. wanted distortion, expands the color gamut quite con- siderably.
    [Show full text]
  • Working with Halftones
    Making Halftone negatives First convert your document to a bitmap file. When printing on an Epson choose 1440 dpi. When printing to a laser printer choose 1200 dpi. When you get the Option window choose Method -> Halftone Screen. Now choose your halftone screen frequency, which may be around 100 lpi for commercial printing, or for an art project. To reduce the likelihood of a moire pattern, it is best to specify different screen angles for each color. Traditionally these were set at 45º for Cyan, 75º for Magenta, 90º for Yellow and 105º for Black. Notice the darker colors are 30º from each other and yellow is set halfway between Magenta and Black. If you’re outputting a duo or tri tone set each 30º from each other. For dot shape, the ellipse halftone dot is often recommended for screen-printing. The following are from http://www.kevinhaas.com Creating a Halftone Bitmap 1. You will need a grayscale file that is at least 150ppi at the size you will print it. This information can be checked by going to Image > Image Size... in Photoshop. 2. Convert the image into a Bitmap: Go to Image > Mode > Bitmap. Set your Output Resolution to 720 and Method to ‘Halftone’. The Output Resolution should be your lpi x 16, and evenly divisible by your printer’s maximum output resolution. For example, a 35lpi halftone needs an Output Resolution of at least 560, but 720 is the next higher resolution that is the inkjet printer’s resolution of 1440 evenly divided by 2. 3.
    [Show full text]
  • Federal Wage System Glossary of Printing Terms for the 4400 Job Family
    Glossary of Printing Terms for the 4400 Job Family TS-45 October 1981 Federal Wage System Glossary of Printing Terms for the 4400 Job Family The terms and definitions contained in this glossary are intended to facilitate the application of published job grading standards to occupations in the Printing Family. The glossary does not represent a comprehensive listing of technical terms and processes common to printing occupations. Additional information may be found in dictionaries, and technical publications such as agency guides, trade magazines, and technical manuals. Aluminum Plate. A thin sheet of aluminum used in lithography for some press plates; image applied photographically; used for both surface-type and deep-etch offset plates. Aperture. A small opening in a plate or sheet. In cameras, the aperture is usually variable in the form of an iris diaphragm and regulates the amount of light which passes through the lens. The working aperture is the diameter of that part of the lens actually used. Asphaltum. A bituminous mixture used as an acid resist or protectant in photomechanics. In lithography, used to make printing image on press plate permanently ink-receptive. Autoscreen (Film). A photographic film embodying the halftone screen; exposed to a continuous-tone image, produces a dot pattern automatically just as if a halftone screen had been used in the camera. Backing-Up. Printing the other side, of a printed sheet. Back Pressure. The squeeze pressure between the blanket (offset) cylinder and the impression cylinder; sometimes called "impression pressure." Base Color. A first color used as a background on which other colors are printed.
    [Show full text]
  • Computer-To-Screen & Film Technologies for Screen Printing
    MANAGEM ENT Computer-to-Screen & Film Technolo- gies for Screen Printing Research and development in new technologies is growing as screen printing continues to compete with alternative imaging technologies. There are several technology choices Higher D-max measurements indicate Another important metric to consider for generating film positives or imaging greater opacity to light. So, a D-max of when choosing a device is its resolution, stencils for screen printing, but choosing 4.50 has a greater ability to block light than usually expressed as dots per inch (dpi). New Products! New Pricing! which to use can be an overwhelming task. a D-max of 4.00. The minimum D-max This standard of measurement indicates the Presented here are the major technologies value recommended for screen printing addressable resolution of an output device When image quality matters, sign on to 3M ©3M 2007. AllRights Reserved©3M 2007. currently used, how they operate and purposes is 3.5 D. However, lower values or printer. It properly refers to the spots of Promotional Products. additional specifications. may provide suitable results for non-critical light or energy used by imagesetters and Research and development in new work or short production runs. If the D- digital-direct exposure systems; or dots Whether your need is for general sign, floor or window technologies is growing as screen printing max value falls below 3.0 D, light will of ink or toner used by an inkjet or laser continues to compete with alternative pass through and prematurely expose the printer, to output your text and graphics.
    [Show full text]
  • 1 Human Color Vision
    CAMC01 9/30/04 3:13 PM Page 1 1 Human Color Vision Color appearance models aim to extend basic colorimetry to the level of speci- fying the perceived color of stimuli in a wide variety of viewing conditions. To fully appreciate the formulation, implementation, and application of color appearance models, several fundamental topics in color science must first be understood. These are the topics of the first few chapters of this book. Since color appearance represents several of the dimensions of our visual experience, any system designed to predict correlates to these experiences must be based, to some degree, on the form and function of the human visual system. All of the color appearance models described in this book are derived with human visual function in mind. It becomes much simpler to understand the formulations of the various models if the basic anatomy, physiology, and performance of the visual system is understood. Thus, this book begins with a treatment of the human visual system. As necessitated by the limited scope available in a single chapter, this treatment of the visual system is an overview of the topics most important for an appreciation of color appearance modeling. The field of vision science is immense and fascinating. Readers are encouraged to explore the liter- ature and the many useful texts on human vision in order to gain further insight and details. Of particular note are the review paper on the mechan- isms of color vision by Lennie and D’Zmura (1988), the text on human color vision by Kaiser and Boynton (1996), the more general text on the founda- tions of vision by Wandell (1995), the comprehensive treatment by Palmer (1999), and edited collections on color vision by Backhaus et al.
    [Show full text]
  • Scanning & Halftones
    SCANNING & HALFTONES Ethics It is strongly recommend that you observe the rights of the original artist or publisher of the images you scan. If you plan to use a previously published image, contact the artist or publisher for information on obtaining permission. Scanning an Image Scanning converts a continuous tone image into a bitmap. Original photographic prints and photographic transparencies (slides) are continuous tone. The scanning process captures picture data as pixels. Think of a pixel as one tile in a mosaic. Bitmapped images Three primary pieces of information are relevant to all bitmapped images. 1. Dimensions Example: 2" x 2" 2. Color Mode Example: 256 level grayscale scan 3. Resolution Example: 300 ppi Basic Steps of Scanning 1. Place image on scanner bed Scanning & Halftones 2. Preview the image – click Preview 3. Select area to be scanned – drag a selection rectangle 4. Determine scan resolution (dpi or ppi) 5. Determine mode or pixel depth (grayscale, color, line art) 6. Scale selected area to desired dimensions (% of original) 7. Scan Resolution Resolution is the amount of something. something amount amount over physical distance fabric the number of stitches in fabric the number of stitches per inch in a needlepoint film the amount of grain in film the number of grains in a micro meter in film digital image the number of pixels the number of pixels per inch in a digital image Resolution is a unit of measure: Input Resolution the number of pixels per inch (ppi) of a scanned image or an image captured with a digital camera On Screen Resolution the number of pixels per inch displayed on your computer monitor (ppi or dpi) Output Resolution the number of dots per inch (dpi) printed by the printer (laser printer, ink jet printer, imagesetter) dpi or ppi refer to square pixels per inch of a bitmap file.
    [Show full text]
  • Chapter 5 Autocorrelation-Driven Restoration of Scanned Color Halftones
    Chapter 5 Autocorrelation-driven restoration of scanned color halftones “An optimist is a person who sees a green light everywhere, while a pessimist sees only the red stoplight... The truly wise person is colorblind.” –Albert Schweitzer Color is experiencing a renaissance in the world of document image understanding. This renewed interest is due, in part, to the ubiquity of inexpensive color scanners on desktops, as well as the availability of cheap disk space and powerful CPUs. Com- pounding this, the proliferation of mass produced color documents, in concert with advances in commodity color scanning technology, creates the expectation that docu- ment understanding systems cope effectively with color. The increasing computation power and storage capacity of desktop workstations at least admits the possibility that color document understanding systems can be built. Color documents, particularly scanned halftone documents, present unique chal- lenges to document understanding systems. Switching to color analysis immediately causes a combinatorial increase in representation alone, and solved problems in the binary or greyscale domain become open issues again. Even the problems of fore- ground/background separation and layout segmentation are affected by uncertainty introduced by color. Indeed, most research on the topic has been limited to attempt- ing to cope with the complexity introduced by color, and researchers have not begun exploiting the potential richness in representation that color offers. Typical approaches to reducing this complexity include color clustering in RGB-space [100, 119], which clus- ters colors that are close in the RGB-cube under the assumption that they are close spatially; adaptive partitioning of RGB-space [43], which adaptively identifies clusters in RGB-space and assigns them a unique label; and chromatic/achromatic color clas- sification [118], which identifies chromatic elements in a document image in order to segment foreground from background.
    [Show full text]
  • DIGITAL HALFTONE Wayne Weiyi Chen
    DIGITAL HALFTONE Wayne Weiyi Chen 1.1. INTRODUCTION The final workflow of any digital photography is to print out the image. This procedure is actually very similar to what the digital display doing: both of them distribute small dots into the space with different size and density to create illusions that there is different color or luminance. Digital Halftone is the method that we use to create a ready-to-print image. The basic idea behind is using different threshold to windowing the image so that the density of dots can be distinguished according to the intensity of grayscale images. In this problem, we will investigate this procedure and implement two categories of different methods. We will briefly introduce these two categories of algorithm and then show their results, compare their performance and give a discussion on that. Figure 1. man.raw Page 1 of 16 1.2. METHODOLOGY 1.2.1. Dithering Matrix The idea of dithering matrix is that instead of introducing noise to the image for thresholding out different density of dots, we generate the threshold matrix with its element fluctuating in a certain range. By doing this, we are able to halftone grayscale images into binary images with different distributions of dots without adding noise. A 2nd order Bayer index matrix is defined as éù02 (8) I2 = êú ëû31 The higher order Bayer index matrix is recursively defined as éù442´´IInn+ I2n = êú (9) ëû4341´IInn+´+ After a Bayer index matrix is generated, we can use it to form a threshold matrix using the formula: Ixy( ,) + 0.5 Txy( ,) =2n ´ 255 N 2 (10) xy,Î-{ 0,1,2,...,2 n 1} where N is the size of the image.
    [Show full text]
  • Altering Grayscale Images to Compensate for Press Fingerprints by Jerry Waite
    Altering Grayscale Images to Compensate for Press Fingerprints by Jerry Waite Grayscale images are generally made from black- deformation, describe a method for fingerprinting and-white or color continuous-tone photographs. an individual press, then explain how Adobe Original photographs are digitized using one of a Photoshop can be used to match a grayscale image to number of scanning techniques—ranging from a particular fingerprint. desktop scanners to Kodak PhotoCD equipment— and saved as computer files. Saved digital files can Variables Affecting Tone Range then be opened directly by page layout programs, Compression and Halftone Dot such as Adobe PageMaker or QuarkXPress, placed in Deformation the desired position on a page, and then output to laser printers, imagesetters, platesetters, or digital on- Copy Density Range demand printing equipment. Original continuous tone photographs are com- Unfortunately, grayscale images placed directly into posed of thousands of varying tones ranging from page layout programs will probably look terrible white to black. Each tone can be described in terms when printed on a printing press because such of its density, or darkness.The density value of any images have not been altered to compensate for the tone can be measured numerically using a special effects caused by the printing process. In particular, instrument called a densitometer. White tones are each printing process—indeed each printing mach- not very dark, so they have low density numbers ine—causes two types of changes to the grayscale near zero. Conversely, black tones are very dark, so image: tone range compression and halftone dot they have high density values—2.00, for example.
    [Show full text]
  • US2165407.Pdf
    v Patented lJuly 1 l, 193.9 This invention relates to photo-mechanical to l. my? invention, Ainl'imakirig f a color; printer?r from processes for the reproduction of a multi-colored@ this negativa ...,1. 1. 1;;1. "ff/"'7 original. It relates to the makingl of color .Í.Fig. ¿1d illustrates a corrected color--sep'arationï printer for use in such a process andßmoref'p'ar# positive y`¢;>'1‘•‘printérresulting from my'process..y 'f „ p* ticularly to a color printer which is correctedior­ »Y . Fig. '2.i11ustra'tes 'a' novel picture ' which can'> be -5 the limitations of the best contemporarily avail-_ ' made. according to. one‘embodiment ïof my ‘inven-f: able inks. > . It is an object of vthe invention Ato aA tion.'My invention. is ` primarily-' >~concerned -. ‘ ­ vlvvithï'the method of making a color-correctedcolor printer.. makin‘glrof acorrectedicolor printer Vfromfa pri-L.y Various methods of color correction generally mary. color v'separation ` negative ‘which "has `¿been­ .10 rca1led"‘masking methods” are wellknownii"Itisv made in’anyfof the usual Ways. f Afpo‘s‘itive‘ madey an object of the present invention‘to providea from-i. a fcolorf separatiomnegative ­may­ comprise' method of color correction which" might : ybe the .printers itself> or Vvthe " printer v‘may b'e“ made termed "autographic” and whichdoesnot require“ therefrom7 by any‘f‘suitable duplicating " process.> 15 the use of special masks but employs the original OneVH Well-knov‘vn ‘method I of introducing».` color 15 itself, or more exactly a color separationimagefof correction infth’eï making ‘of fa' color ‘printer com# the original, to act as a mask.y ‘ > f »Y prises` masking ‘certain'of'ïthe color 1Vseparation.
    [Show full text]