C545 User-Manual.Pdf
Total Page:16
File Type:pdf, Size:1020Kb
MODEL PART DIAGRAM CONTROL PANNEL 08. Power Button 13. Light Sensor FRONT Back 01 02 03 4 05 06 Turns the unit on or off. During the first 30 seconds of Detects the amount of ambient light in the power, the Air Quality Indicator will cycle through Blue, environment. When in Auto Mode, the light sensor Amber and Red colors. detects when to put the unit into sleep mode. • Smart Sensor takes approximately 4 minutes to Control Panel Air Outlet gauge the air quality in the environment before WINIX SMART Wi-Fi Setup Vent normal operation begins. Before you begin, make sure you have a wireless router that is 2.4Ghz and have a Smart phone that is Handle 09-1. Fan Speed/Auto/Sleep Buttons Android 5.0 and later or iOS 10.0 and later. Reference Use the Fan Speed arrow buttons to set the desired fan the Winix Smart Wi-Fi Set Up Guide for more details. speed. Fan Speeds cycle over in this sequence : Auto, • Latest Phone Operating System requirements are Low, Medium, High, Turbo, Sleep, Auto. subject to change based on future phone technology Front Panel and app version updates. 09-2. PlasmaWave® Button Press and hold the two arrow buttons + for 1 Download the WINIX SMART C545 app on your device. Power plug 3 seconds. • available via Google Play store or iTunes App store. 07 08 09 10 11 12 13 Press the Plasmawave® button, when the unit is on, to 2 Run the app and follow the setup guide to connect ® enable or disable this feature. By default, PlasmaWave your device to the unit. is enabled whenever the unit is powered on. 01. Auto Mode 04. Sleep Mode When the unit is running, you may hear a chirping or ① Select "New Unit" and choose C545 to connect The LED "Auto" light will indicate when Auto mode is The LED "Sleep" light will indicate when Sleep mode is buzzing sound. to this model. activated. activated. The sound is from large particles passing through ② Read the notice and select "OK". • When in Auto Mode the Fan Speed is automatically • When Sleep mode is activated, the Air Quality PlasmaWave®, it is normal and does not signify product ③ Enter the password to your Wi-Fi network. WHERE TO USE adjusted according to the indoor air quality. Indicator LED light is disabled. failure. Press and hold the Wi-Fi button on the unit's As the indoor air quality improves, the fan speed will • When Sleep mode is "activated", the fan speed is ④ ® control panel until it beeps. automatically be decreased. If the indoor air quality automatically set to quiet. 10. PlasmaWave Indicator Allow 12 ~ 18 in. of space between TVs, radios, and other electronics worsens, the fan speed will automatically increase. Indicates whether PlasmaWave® is enabled or disabled. • The Wi-Fi strength indicator will begin to blink. 05. Check Filter electromagnetic interference from certain electronics may cause ⑤ Connect to the WINIX SMART network via your 02. Air Quality Indicator product malfunction. LED light indicates when it is time to change the filter. 11. Wi-Fi Button device's network menu. Color-coded LED indicates one of three levels of air quality. • Press for 3 seconds to activate pairing mode. Place indoors away from direct sun light 06. Filter Reset Button ⑥ Selecting "Next" will connect your unit to your • The three levels of air quality are : • When Wi-Fi is paired, press the button to turn Wi-Fi device. direct exposure may cause product malfunction or failure. BLUE (good), AMBER (fair), RED (poor). LED light indicates when it is time to change the filter. off or back on. ⑦ Define the unit settings (Name and Location). Only place on hard, flat surfaces • After replacing the True HEPA Filter, use a small object 03. Fan Speed 12. Wi-Fi Indicator When set up is complete, the WINIX SMART 4 flimsy or slanted surfaces may result in abnormal noise and vibrations. such as a paper clip, to press and hold the reset button ⑧ Indicates the current fan speed. for at least 5 seconds until the Check Filter light turns off. • Enables or disables the Wi-Fi feature. Indicator will light up. Allow at least 4 in. from walls • When in the pairing state, the Wi-Fi LED flashes. 07. Smart Sensor for maximum air flow. • When paired successfully, the Wi-Fi LED will be a When in Auto Mode, the Smart Sensor detects the amount solid white light. of impurities in the environment to adjust fan speeds. 1 2 3 4-STAGE AIR PURIFICATION INITIAL OPERATION REPLACING FILTERS 03 After replacing a filter, Latch 02 press the RESET button for at least 5 seconds. 01 1 Pre-filter 2 Activated Carbon Filter 3 True HEPA filter 4 PlasmaWave® CLEANING CARE 01. Pre-filter 02. Activated Carbon Filter 1 Remove the front panel by grasping its upper 4 Install the filters until they fit securely in place. Designed to catch larger airborne particles found indoors. Reduces VOCs and household Odors from cooking, edge and gently pulling forward. 03. True HEPA Filter (back) Cleaning the filters Cleaning the Exterior & Interior pets, and smoke. 02. Activated Carbon filter (middle) 03. True HEPA filter 01. Pre-Filter (front) ® Captures 99.97%* of airborne allergens including; pollen, 04. PlasmaWave Mold spores, dust, pet dander, microbes, and smoke. Attacks pollutants at a molecular level to neutralize *particles as small as 0.3 microns in size. bacteria, chemical vapors, odors and gases from the air. Latch MAINTENANCE Use a vacuum cleaner or soft brush to clean Wipe with a soft damp cloth using room temperature When to Replace Filters the Pre-filter. water. Filter Indicator Light When to service When to replace 2 Remove the Pre-Filter, then the bag of filters 5 After filters are installed close the front panel. • If it is excessively soiled, rinse in room temperature • Afterwards, wipe it down with a clean dry cloth. water. behind it. Open the front panel and clean the interior with a Pre-filter none Clean once every 14 days Permanent • Do not use detergent or soap. vacuum cleaner. • Allow the filter to dry for 24 hours or more before using. Activated • For optimal performance, clean every 1 - 2 months. none Replace every 3 months Carbon Filter • Intervals between filter cleaning may vary Can NOT be WASHED depending on the air quality. NOTICE Lasts Approx. True HEPA Filter • When cleaning the unit, always unplug the power cord 6 ~ 12 months NOTICE first and then wait until the unit has cooled down. • Do not use benzene, alcohol, or other volatile • When the Check Filter indicator LED is on, it is time to replace the True HEPA Filter. • Never disassemble, repair, or modify this unit yourself. fluids, which may cause damage or discoloration. • Do not use flammable sprays or liquid detergents. • Intervals between filter replacement may vary depending on environment. o • Do not use hot water over 104 F or volatile fluids • Do not allow children to clean or maintain the unit. such as paint thinner. 3 Remove filters from protective plastic wrap. 6 Insert the power cord into an electrical outlet. • Before cleaning or maintaining, ensure unit is unplugged. 4 5 6 User Manual SAFETY AND CAUTIONS SAFETY INSTRUCTIONS Thank you for purchasing a Winix air purifier. This product is for household use only. Before operating this equipment, carefully read and Do not pull on the power cord when unplugging the follow these safety cautions unit. IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER AIR PURIFIER Ensure filters are inserted before running unit Do not tie or knot the power cord when unit is in Running the unit without filters can shorten the units operation. WARNING : Follow the instructions in this manual to reduce the risk of electric shock, short circuit, and/or fire. life and cause electric shock or injury. If the unit becomes submerged in water, unplug it • Do not repair or modify the unit unless All other repairs • If the power plug is damaged, it must be replaced by Be sure foreign objects are NOT inserted into the and contact customer service. should be completed by a qualified technician. the manufacturer or a qualified technician. vents on the unit Do not unplug or move the unit while in operation. • The plug for this unit is polarized with one blade wider • Remove the power plug from the outlet when not in use. Objects can include pins, rods, and coins. than the other. Do not force the plug into an electrical • Do not handle the power plug with wet hands. Do not touch any part of the interior of the unit with Do not plug additional appliances into the same outlet. Do not alter the plug in any way. If the does not wet hands outlet or power supply. fit into the outlet, reverse the plug. If it still does not fit, • Do not operate the unit when using indoor smoke- contact a qualified technician to install a proper outlet. generating insecticides. The high voltage may cause electric shock. Do not touch the plug with wet hands. Ensure unit intake and outlet vents do not become blocked • Do not use if the power cord or plug is damaged or the • Do not clean unit with benzene or paint thinner. Unplug the unit when not in operation for extended connection to the wall outlet is loose. Do not spray insecticides on the unit. Blockage may lead to increased internal termperatures periods of time. causing product failure and derformation. • Use AC 120V only. • Do not use the unit where it is humid or where the unit Do not place around heating elements.