DOCSLIB.ORG

New Results in Medium Voltage Cable Assessment Using Very Low Frequency with Partial Discharge and Dissipation Factor Measurement

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
New Results in Medium Voltage Cable Assessment Using Very Low Frequency with Partial Discharge and Dissipation Factor Measurement C I R E D 17th International Conference on Electricity Distribution Barcelona, 12-15 May 2003 NEW RESULTS IN MEDIUM VOLTAGE CABLE ASSESSMENT USING VERY LOW FREQUENCY WITH PARTIAL DISCHARGE AND DISSIPATION FACTOR MEASUREMENT Martin BAUR, Peter MOHAUPT, Timo SCHLICK BAUR Prüf- und Messtechnik GmbH - Austria [email protected] INTRODUCTION Figure 1 shows a typical electrical tree using power frequency 50 Hz. One can see a wide, bush like distributed tree at the source of the needle The paper presents actual field test results using a electrode. diagnostic system based on Very Low Frequency with 0.1 Hz sinusoidal waveform. The state of the art of a new diagnostic tool offers the user of underground cable systems and networks an efficient approach of maintenance support allowing highly efficient measurement procedures to judge the ageing characteristics, the rejuvenation requirements and a more precise investment planning forecast. On the other hand, the method offers just in time replacement and preliminary Figure 1: Electrical treeing on a XLPE cable detection of incipient faults, long before their sample with a needle defect at power breakdown. Using this diagnostic tool properly, the frequency 50 Hz cost of ownership, replacement, maintenance and “outage” costs can be reduced dramatically, at the Figure 2 shows the same test sample arrangement same time reaching far better system reliability and with an electrical tree at VLF test voltage at 0.1 Hz. power distribution redundancy. The tree structure is reduced to a single needle tree channel. The main reason lies in the much higher In the past, medium and high voltage cables were discharge capacity at power frequency compared to tested with DC. Advantages were given by low VLF. The number of discharges decreases per unit weight, portable, easy to use, economic, field of time proportionally to the frequency applied. proven test equipment. After introduction of Since the amount of discharges in one channel at synthetic HV insulation like PE, XLPE, EPR or power frequency is much higher, the material earlier PVC DC test voltages were also used. The destruction is higher; the gas pressure will increase test results with DC were restricted with limited the dielectric strength according to Paschens law. information or sometimes with destructive So, the tree growth is reduced. At VLF there is consequences [1]. Even more, the DC test may enough time for the gas to diffuse in the surrounding cause cable failures due to the low dissipation factor of the discharge channels, creating a lower pressure of PE or XLPE insulation and possible space within the tree, decreasing the breakdown level charges causing local field stress after reenergizing further. As a consequence, the tree growth at VLF is the AC power. This is the reason of introducing new much faster compared to power frequency. In fact, after laying test standards based on AC test voltage tree growth at power frequency might have 1.7 [2]. mm/h compared to VLF 12.3 mm/h. In the case of defects in the insulation, as proven in [3], the VLF voltage stress will lead much faster to a VLF-TESTING breakdown compared to power frequency. Therefore the VLF test voltage is a very good tool to compare between good or bad cables. It also shows During the commissioning of a cable or during a much better sensitivity compared to conventional maintenance it is beneficial to detect defects at an test methods: early stage before incipient failure of the insulation occurs. Furthermore the test should not reduce the cable lifetime. Investigations [3] have shown that by using a Very Low Frequency (VLF) test voltage better results, as opposed to other test voltage waveforms are possible. The following short scientific explanation will clarify the background of the VLF test method. BAU_Baur_A1 Session No 1 Paper No 74 - 1 - C I R E D 17th International Conference on Electricity Distribution Barcelona, 12-15 May 2003 Figure 2: Electrical treeing on a XLPE cable sample with a needle defect at VLF test voltage 0.1 Hz. Figure 4: Relative voltage on a model cable with different types of damages [3] Figure 3 shows the distribution of breakdowns over the testing time. These tests are results of practical field tests. The sensitivity in the case of XLPE is DISSIPATION FACTOR MEASUREMENT obvious. Almost 2/3 of cable failures are breaking (TAN DELTA TD) down after a VLF testing time of 10 min. Also The results on mass impregnated or oil filled cables are very good. Earlier PE or XLPE medium voltage cables now Different waveforms and test frequencies are not show extended water treeing (WT) phenomena’s. comparable in their breakdown mechanism. The lifetime of these cables is greatly reduced, [5,6,7]. A large amount of practical field experience has proven that there is a close relation between WT and VLF dissipation factor (TD). A very clear 60 assessment of degradation criteria can be measured [8]. The existing assessment criteria’s are 40 based on XLPE cable insulation compounds. Not 20 only the absolute value of TD measured with VLF at 0.1Hz at nominal rated cable voltage level 0.5Uo up 0 to 2Uo (phase to ground), but also the increase of 0-10 10- 20- 30- 40- 50- plastic TD over the rise of voltage are important factors. min 20 30 40 50 60 XLPE min min min min min Wrapped joint Fig. 6 represents the TD criteria for good, medium Paper DNAKBA aged or highly serviced aged, bad XLPE insulation Figure 3: Amount of breakdowns during the test time in min on different types of cables and accessories [4]. in the range of 0.5Uo up to 2.5Uo. TD diagnostic voltage levels are usually limited at 2Uo. The rate of In Figure 4 it seems that the sinusoidal VLF at 0.1Hz rise between Uo and and 2Uo is another important is the most sensitive in respect of dielectric strength. criteria [5,6,7]. Mechanical damages need only by 40% of the breakdown voltage compared to other methods One has to be aware of the damping characteristics TD at 2Uo when using oscillating wave (OSI), the dielectric 10-1 field stress over time is changing according to the > 2.2x10-3 insulation with length of the cable tested. Several standards such 10 -2 high degradation as VDE, CENELEC and IEEE have adopted the -3 > 1.2x10 service aged VLF site-test being adequate for medium cable after XLPE laying commissioning and maintenance test method 10-3 cable insulation [2,3]. < 1.2x10-3 new XLPE cable The future IEC 60060-3 standard on High Voltage insulation Test Techniques will recommend the alternative -4 10 methods voltage with sinusoidal very low frequency at 0.1 Hz as a voltage test and for diagnostic tests such as dissipation factor measurement and partial Figure 5: Absolute TD value assessment criteria on XLPE discharge measurement [3]. cables [8]. BAU_Baur_A1 Session No 1 Paper No 74 - 2 - C I R E D 17th International Conference on Electricity Distribution Barcelona, 12-15 May 2003 the location of PD sources. The question is e.g. the source type and the location at Uo or at 1.7Uo. -3 In most cases the PD does not result from the tan δ . 10 internal cable insulation, but from the accessories 7 like joints or terminations. Therefore the source location becomes more important. 6 An example is shown in the chart Figure 7. The different accessories, the cable insulation, 5 distinguishing the partial discharge inception voltage level (PDIV) and the distribution at practically tested 4 in mass impregnated cable insulation is shown [13]. 3 0,1 Hz dissipation factor 2 100% 20% 90% 1 80% 37% 70% 28% 0 60% 0 0,5 1 1,5 2 2,5 3 50% U / U 0 40% 24% 30% 52% reference cable (new) slightly service-aged (1) 20% 10% 12% moderately service-aged (2) moderately service-aged (3) 0% PDIV PD location strongly service-aged (4) cable joints cable terminations cable insulation Figure 6: Assessment criteria with Voltage TD Ratio on XLPE service aged cables [7,8]. PD activity > 1,3Uo PD activity up to 1,3Uo In fact the TD diagnosis on mass impregnated or oil PD activity up to Uo filled paper insulated cables is also a good Figure 7: Distribution and PDIV levels and location of assessment tool. Because of completely different PD in the case of paper insulated cables [13]. physical assembly of the cable insulation other more individual criteria’s have to be applied with VLF TD. Today, only limited experience is available. In the case of PE or XLPE cables only a few pC are The TD comparison has given useful results enough or only a short time (hours or days) is between phases or between similar types of the needed to break down the internal insulation. same lot of cable production. Whereas sometimes several years of several 100 In such a way different and critical cables can be pC or even nC are needed to initialize a complete identified. Many different authors worldwide have breakdown in case of paper mass impregnated approved the efficiency of the method. cables. Since practice shows that breakdowns are experienced in more than 50% of the accessories, the PD density and location measurement is of PARTIAL DISCHARGE MEASUREMENT AND greatest importance. A PD measuring level above LOCATION OF FAULTS (PD) 10 pC seems to be practical and more than enough for on site testing. Easy to use and portable test equipment are more important factors. Equipment For decades the PD measurement and the location with low level PD detection are available too; they based on time base propagation fault location has normally need a profound expert knowledge for field been the most important and efficient non- applications.
Load more

Recommended publications
  • Partial Discharges and Iec Standards 60840 and 62067: Simulation Support to Encourage Changes
    M. Batalović i dr. Parcijalna pražnjenja i IEC standardi 60840 i 62067: Simulacijska podrška za poticanje promjena ISSN 1330-3651 (Print), ISSN 1848-6339 (Online) DOI: 10.17559/TV-20141118124625 PARTIAL DISCHARGES AND IEC STANDARDS 60840 AND 62067: SIMULATION SUPPORT TO ENCOURAGE CHANGES Mirza Batalović, Kemo Sokolija, Mesud Hadžialić, Nejra Batalović Preliminary notes This paper addresses some shortcomings of existing IEC standards related to analyses of cable systems with polymer insulation (IEC 60840 and IEC 62067). The focus is on partial discharges measurement, completely neglected in present version of these standards, and justification of the needs for their inclusion in the standards through appropriate procedures. If included in the standards the procedures would provide an effective way to identify and detect the defects that might appear during the cable system installation and to forestall their appearance during exploitation. The simulation evidences, to suggest and justify the changes in the standards, through a modelling of partial discharge phenomena using contemporary software tool (COMSOL) are provided in this paper. Keywords: COMSOL model; IEC standards; partial discharges Parcijalna pražnjenja i IEC standardi 60840 i 62067: Simulacijska podrška za poticanje promjena Prethodno priopćenje Ovaj rad upućuje na izvjesne nedostatke postojećih IEC standarda koji se odnose na analizu kabelskih sistema s polimernom izolacijom (IEC 60840 i IEC 62067). Fokus je na mjerenju parcijalnih pražnjenja, potpuno zanemarenih u aktualnoj verziji ovih standarda,te opravdanosti potreba za njihovo uključenje u standarde kroz odgovarajuće procedure. Ukoliko bi se uključile u standarde, procedure bi osigurale učinkovit alat za identifikaciju i detekciju defekata koji se mogu pojaviti za vrijeme instalacije kabelskih sistema i spriječiti njihovu pojavu tijekom eksploatacije.
    [Show full text]
  • Understanding Electrical Treeing Phenomena in Xlpe Cable Insulation Adopting Uhf Technique
    Journal of ELECTRICAL ENGINEERING, VOL. 62, NO. 2, 2011, 73–79 UNDERSTANDING ELECTRICAL TREEING PHENOMENA IN XLPE CABLE INSULATION ADOPTING UHF TECHNIQUE ∗ ∗ ∗∗ Ramanujam Sarathi — Arya Nandini — Michael G. Danikas A major cause for failure of underground cables is due to formation of electrical trees in the cable insulation. A variety of tree structure can form from a defect site in cable insulation viz bush-type trees, tree-like trees, fibrillar type trees, intrinsic type, depending on the applied voltage. Weibull studies indicate that a higher applied voltage enhances the rate of tree propagation thereby reducing the life of cable insulation. Measurements of injected current during tree propagation indicates that the rise time and fall time of the signal is of few nano seconds. In the present study, an attempt has been made to identify the partial discharges caused due to inception and propagation of electrical trees adopting UHF technique. It is realized that UHF signal generated during tree growth have signal bandwidth in the range of 0.5–2.0 GHz. The formation of streamer type discharge and Townsend type discharges during tree inception and propagation alters the shape of the tree formed. The UHF signal generated due to partial discharges formed during tree growth were analyzed adopting Ternary plot, which can allow one to classify the shape of tree structure formed. K e y w o r d s: power cables, cable insulation, partial discharge, UHF signal, electrical breakdown, failure analysis, XLPE, ternary plot 1 INTRODUCTION The conventional method of identifying the discharges is through identification of luminous discharges from the In recent times, cross linked polyethylene (XLPE) ma- defect site due to tree propagation, acoustic signal radi- terial is used as insulation material in high voltage AC ated during tree propagation and by measuring the par- and DC cables.
    [Show full text]
  • Ageing in Epoxy Resin As a Precursor to Electrical Treeing
    Ageing in Epoxy Resin as a Precursor to Electrical Treeing A thesis submitted to the University of Manchester for the degree of Doctor of Philosophy in the Faculty of Science and Engineering 2020 Harry McDonald School of Engineering Department of Electrical and Electronic Engineering Table of Contents Abstract ................................................................................................................................................. 11 Acknowledgements ............................................................................................................................... 13 1. Introduction .................................................................................................................................. 14 1.1. Cables .................................................................................................................................... 14 1.1.1. Cable Background ......................................................................................................... 14 1.1.2. XLPE Cables ................................................................................................................... 16 1.1.3. Electrical Tree Formation .............................................................................................. 17 1.2. Electrical Treeing Background ............................................................................................... 18 1.2.1. Stages of Electrical Treeing ..........................................................................................
    [Show full text]
  • Electrical Treeing: a Phase-Field Model
    Title Electrical treeing: A phase-field model Author(s) Cai, Ziming; Wang, Xiaohui; Li, Longtu; Hong, Wei Extreme mechanics letters, 28, 87-95 Citation https://doi.org/10.1016/j.eml.2019.02.006 Issue Date 2019-04 Doc URL http://hdl.handle.net/2115/79673 © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license Rights https://creativecommons.org/licenses/by-nc-nd/4.0/ Rights(URL) https://creativecommons.org/licenses/by-nc-nd/4.0/ Type article (author version) File Information manuscript-electric-treeing-WH-19-2-18-no-mark.pdf Instructions for use Hokkaido University Collection of Scholarly and Academic Papers : HUSCAP Electrical treeing: a phase-field model Ziming Caia,d, Xiaohui Wanga, Longtu Lia, Wei Hongb,c,d* a State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, Beijing 100084, PR China b Department of Mechanics and Aerospace Engineering, Southern University of Science and Technology, Shenzhen, Guangdong 518055, PR China c Global Station for Soft Matter, Global Institution for Collaborative Research and Education, Hokkaido University, Sapporo, Japan d Department of Aerospace Engineering, Iowa State University, Ames, IA 50010, USA Corresponding Author *Wei Hong, E-mail: [email protected] Abstract Electrical treeing is a commonly observed phenomenon associated with dielectric breakdown in solid dielectrics. In this work, a phase-field model is developed to study the initiation and propagation of electrical trees in two different geometries: a parallel capacitor and a cylindrical capacitor. The model utilizes a continuous field of damage variable to distinguish the localized damaged regions from the undamaged bulk material.
    [Show full text]
  • Electrical Treeing in Power Cable Insulation Under Harmonics Superimposed on Unfiltered HVDC Voltages
    energies Article Electrical Treeing in Power Cable Insulation under Harmonics Superimposed on Unfiltered HVDC Voltages Mehrtash Azizian Fard 1,* , Mohamed Emad Farrag 2,3 , Alistair Reid 4 and Faris Al-Naemi 1 1 Department of Engineering and Mathematics, Sheffield Hallam University, Sheffield S1 1WB, UK 2 Department of Engineering, Glasgow Caledonian University, Glasgow G4 0BA, UK 3 Faculty of Industrial Education, Helwan University, 11795 Helwan, Egypt 4 School of Engineering, Cardiff University, Cardiff CF10 3AT, UK * Correspondence: [email protected]; Tel.: +44-114-225-2897 Received: 28 June 2019; Accepted: 13 August 2019; Published: 14 August 2019 Abstract: Insulation degradation is an irreversible phenomenon that can potentially lead to failure of power cable systems. This paper describes the results of an experimental investigation into the influence of direct current (DC) superimposed with harmonic voltages on both partial discharge (PD) activity and electrical tree (ET) phenomena within polymeric insulations. The test samples were prepared from a high voltage direct current (HVDC) cross linked polyethylene (XLPE) power cable. A double electrode arrangement was employed to produce divergent electric fields within the test samples that could possibly result in formation of electrical trees. The developed ETs were observed via an optical method and, at the same time, the emanating PD pulses were measured using conventional techniques. The results show a tenable relation between ETs, PD activities, and the level of harmonic voltages. An increase in harmonic levels has a marked effect on development of electrical trees as the firing angle increases, which also leads to higher activity of partial discharges.
    [Show full text]
  • Electrical Trees and Their Growth in Silicone Rubber at Various Voltage Frequencies
    energies Article Electrical Trees and Their Growth in Silicone Rubber at Various Voltage Frequencies Yunxiao Zhang 1, Yuanxiang Zhou 1,*, Ling Zhang 1,2, Zhongliu Zhou 1 and Qiong Nie 3 1 State Key Lab of Electrical Power System, Department of Electrical Engineering, Tsinghua University, Beijing 100084, China; [email protected] (Y.Z.); [email protected] (L.Z.); [email protected] (Z.Z.) 2 State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an 710049, Shaanxi, China 3 AC Project Construction Branch, State Grid Corporation of China, Beijing 100052, China; [email protected] * Correspondence: [email protected]; Tel.: +86-10-6279-2303 Received: 28 December 2017; Accepted: 26 January 2018; Published: 2 February 2018 Abstract: The insulation property at high voltage frequencies has become a tough challenge with the rapid development of high-voltage and high-frequency power electronics. In this paper, the electrical treeing behavior of silicone rubber (SIR) is examined and determined at various voltage frequencies, ranging from 50 Hz to 130 kHz. The results show that the initiation voltage of electrical trees decreased by 27.9% monotonically, and they became denser when the voltage frequency increased. A bubble-shaped deterioration phenomenon was observed when the voltage frequency exceeded 100 kHz. We analyze the typical treeing growth pattern at 50 Hz (including pine-like treeing growth and bush-like treeing growth) and the bubble-growing pattern at 130 kHz. Bubbles grew exponentially within several seconds. Moreover, bubble cavities were detected in electrical tree channels at 50 Hz. Combined with the bubble-growing characteristics at 130 kHz, a potential growing model for electrical trees and bubbles in SIR is proposed to explain the growing patterns at various voltage frequencies.
    [Show full text]
  • Detection of Electric Treeing of Solid Dielectrics with the Method of Acoustic Emission
    Electr Eng (2012) 94:37–48 DOI 10.1007/s00202-011-0219-1 ORIGINAL PAPER Detection of electric treeing of solid dielectrics with the method of acoustic emission Władysław Opydo · Arkadiusz Dobrzycki Received: 31 August 2009 / Accepted: 5 June 2011 / Published online: 19 June 2011 © The Author(s) 2011. This article is published with open access at Springerlink.com Abstract The paper presents results of research of electrical higher and higher voltage power networks for transmission treeing of solid dielectrics with the method of acoustic emis- of electric power. At the same time, decreasing quantity of sion (AE). The study was performed with an alternating volt- free building areas in these centers force the use of electric age of 50Hz in the range up to 21kV (RMS) on methyl power cables and miniaturization of high-voltage network polymethacrylate or crosslinked polyethylene samples. They equipment. These two factors cause that the electric power were of cuboidal shape of the dimensions 25 × 10 × 4 mm. devices must operate under higher intensity of the electric One of the cuboid sample walls of the dimensions 25×4mm field. Therefore, their high-voltage insulation must be more was covered with a conducting paint. On the opposite wall, perfect. a surgical needle of T-25 type was screwed. The distance In an electric-power device, particularly, the one designed between the electrodes (the needle and the wall covered with for high voltage operation, there occurs a problem of electric a conducting paint) was in the range 0.5–2.0mm. Registered strength of solid materials. Any electric or electric-power signals were denoised with wavelet transformation method device, even the one in which gas, vacuum, or mineral oil and then there were analyzed.
    [Show full text]
  • Cable Insulation with Reduced Electrical Treeing
    (19) TZZ _¥_T (11) EP 2 854 139 A1 (12) EUROPEAN PATENT APPLICATION (43) Date of publication: (51) Int Cl.: 01.04.2015 Bulletin 2015/14 H01B 3/18 (2006.01) (21) Application number: 14190526.5 (22) Date of filing: 14.03.2008 (84) Designated Contracting States: (72) Inventor: Eaton, Robert, F. AT BE BG CH CY CZ DE DK EE ES FI FR GB GR Bell Mead, New Jersey 08502 (US) HR HU IE IS IT LI LT LU LV MC MT NL NO PL PT RO SE SI SK TR (74) Representative: Boult Wade Tennant Verulam Gardens (30) Priority: 15.03.2007 US 894925 P 70 Gray’s Inn Road London WC1X 8BT (GB) (62) Document number(s) of the earlier application(s) in accordance with Art. 76 EPC: Remarks: 08732203.8 / 2 126 934 This application was filed on 27-10-2014 as a divisional application to the application mentioned (71) Applicant: Union Carbide Chemicals & Plastics under INID code 62. Technology LLC Midland, MI 48674 (US) (54) Cable insulation with reduced electrical treeing (57) The present invention relates to a power cable comprising an insulation layer in which he insulation layer comprises a polyolefin polymer and a voltage stab ilizer comprising a conducting polymer. EP 2 854 139 A1 Printed by Jouve, 75001 PARIS (FR) EP 2 854 139 A1 Description FIELD OF THE INVENTION 5 [0001] This invention relates to compositions comprising a polyolefin polymer and an oligomer or polymer with delo- calized electron structure. In one aspect, the invention relates to cables and wires.
    [Show full text]
  • Aperthe Critical Angle of Ultrasonic Electrical Inspection Of
    Transmission Lines and Enclosed Systems Transmission Electrical Inspection of The Critical Angle of Ultrasonic White Paper The Critical Angle of Ultrasonic Electrical Inspection of Transmission Lines and Enclosed Systems By Drew Walts, Level 2 Certified Ultrasound Technician, SME, Training Manager, IRISS Inc. Abstract: Electrical Ultrasound Inspection is one of the most unique applications as it is not dependent on decibel levels as much as the patterns the anomaly produces. However, limited approach restrictions can make it difficult to get the truest form of the Incident Sound Wave for pattern identification. iriss.com Transmission Lines and Enclosed Systems Transmission Electrical Inspection of The Critical Angle of Ultrasonic White Paper Why does Critical Angle Matter? Historically, electrical systems have been scheduled for an annual inspection as mandated by insurance companies. Sometimes, it is simply because the facility does not have the personnel to perform inspections and the inspection is outsourced. Sometimes, it is the mentality of the management and planners that these assets are not as critical or that it takes too many man hours to inspect these assets. When using ultrasound, the inspector scans the seams and openings in equipment to figure out if there is an anomalous condition that needs to be investigated further. With the invention of IR Windows and Ultrasound ports, the time it takes to perform electrical inspections has been dramatically reduced. The IR Windows and Ultrasound Ports allow for a safer process of inspecting these critical assets while in their energized state. The facility can inspect their assets monthly if they wish because there is no need to wear an arc flash suit or remove the panels to perform these inspections.
    [Show full text]
  • Electrical Treeing in Insulation Materials for High Voltage AC Subsea Connectors Under High Hydrostatic Pressures
    Electrical Treeing in Insulation Materials for High Voltage AC Subsea Connectors under High Hydrostatic Pressures Miguel Soto Martinez Wind Energy Submission date: July 2017 Supervisor: Frank Mauseth, IEL Co-supervisor: Dr. Armando Rodrigo Mor, TU Delft DC Systems, Energy Conversion & Storage Dr. Sverre Hvidsten, SINTEF Energy Research Norwegian University of Science and Technology Department of Electric Power Engineering Electrical Treeing in Insulation Materials for High Voltage AC Subsea Connectors under High Hydrostatic Pressures Electrical tree, partial discharge behaviour and light emission in SiR Master of Science Thesis For obtaining the degree of Master of Science in Electrical Engineering at Delft University of Technology and in Technology-Wind Energy at Norwegian University of Science and Technology. Miguel Soto Martinez 06.2017 European Wind Energy Master – EWEM Abstract To enable the next generation subsea boosting and processing facilities, high power electrical connectors are strongly needed and considered one of the most critical components of the system. Electrical tree growth is a precursor to electrical breakdown in high voltage insulation materials. Therefore, the study of the tree growth dependency with hydrostatic pressure is needed to understand the behaviour of the insulation material used in subsea connectors. Silicone rubber (SiR) is used as an insulation material for these applications thanks to its higher viscosity characteristic in comparison with other solid insulation materials used in subsea cables. This property is the main factor that allows the water to be swiped off the connector when a receptacle is mated into the plug of a subsea connector. In addition, the silicone rubber must provide similar electric field control as other insulation materials used in cable terminations and connectors.
    [Show full text]
  • Electrical Treeing Characteristics in XLPE Power Cable Insulation in Frequency Range Between 20 and 500 Hz
    IEEE Transactions on Dielectrics and Electrical Insulation Vol. 16, No. 1; February 2009 179 Electrical Treeing Characteristics in XLPE Power Cable Insulation in Frequency Range between 20 and 500 Hz G. Chen School of Electronics and Computer Science University of Southampton, Southampton SO17 1BJ, UK and C. H. Tham SP Powergrid Ltd, Singapore ABSTRACT Electrical treeing is one of the main reasons for long term degradation of polymeric materials used in high voltage ac applications. In this paper we report on an investigation of electrical tree growth characteristics in XLPE samples from a commercial XLPE power cable. Electrical trees have been grown over a frequency range from 20 Hz to 500 Hz and images of trees were taken using CCD camera without interrupting the application of voltage. The fractal dimension of electric tree is obtained using a simple box-counting technique. Contrary to our expectation it has been found that the fractal dimension prior to the breakdown shows no significant change when frequency of the applied voltage increases. Instead, the frequency accelerates tree growth rate and reduces the time to breakdown. A new approach for investigating the frequency effect on trees has been devised. In addition to looking into the fractal analysis of tree as a whole, regions of growth are being sectioned to reveal differences in terms of growth rate, accumulated damage and fractal dimension. Index Terms — Electrical tree, fractal dimension, box-counting, variable frequency, growth rate, accumulated damage, partial discharge 1 INTRODUCTION NOWADAYS, XLPE cables are widely chosen for power distribution and transmission lines up to 500 kV owing to its excellent electrical, mechanical and thermal characteristics.
    [Show full text]
  • Spacecraft High-Voltage Paschen and Corona Design Handbook
    METRIC/SI NASA TECHNICAL NASA-HDBK-4007 HANDBOOK W/CHANGE 3— REVALIDATED 2020-12-29 National Aeronautics and Space Administration Approved: 2016-10-27 Superseding MSFC-STD-531 SPACECRAFT HIGH-VOLTAGE PASCHEN AND CORONA DESIGN HANDBOOK NASA-HDBK-4007 W/CHANGE 3 DOCUMENT HISTORY LOG Status Document Change Approval Date Description Revision Number Baseline 2016-10-27 Initial Release 1 2020-10-16 Administrative Change: Inactive for New Design—This NASA Technical Handbook is no longer authorized for use in new designs, because it is antiquated, and no new updates have been discovered in the last several years 2 2020-10-22 Administrative Change: Reinstate Active Status—Per NASA Engineering Standards Panel meeting 2020-10- 21. 3 2020-12-29 Administrative Change: Revalidated—This NASA Technical Handbook was reviewed and revalidated with revision to follow. APPROVED FOR PUBLIC RELEASE—DISTRIBUTION IS UNLIMITED 2 of 147 NASA-HDBK-4007 W/CHANGE 3 FOREWORD This NASA Technical Handbook is published by the National Aeronautics and Space Administration (NASA) as a guidance document to provide engineering information; lessons learned; possible options to address technical issues; clarification of similar terms, materials, or processes; interpretive direction and techniques; and any other type of guidance information that may help the Government or its contractors in the design, construction, selection, management, support, or operation of systems, products, processes, or services. This NASA Technical Handbook is approved for use by NASA Headquarters and NASA Centers and Facilities. It may also apply to the Jet Propulsion Laboratory and other contractors only to the extent specified or referenced in applicable contracts.
    [Show full text]