SSC-773V2 Quickstart Guide

SSC-773S4 Quickstart Guide Read Completely Before Using or Assembling

Package Includes  Extra Durable Weatherproof Case with O-ring  1 ea. 22-12VRB-LA battery and Deep Cycle Trickle Charger  1 Single Battery power cables to connect directly to batteries  1 ea. Solar Panel  1 ea. Solar Charge Controller  773 DVR board with remote control (D1 H.264 @ 30fps Recording)  SSC-113WCDN600 600 line Weatherproof Day Night Bullet Camera With 3.6mm Lense  3 extra lenses 8, 12, and 16mm  2 ea. 8Gb SD cards  USB card reader  CA-150 power video cable in order to have camera up to 100 ft away from DVR  Y-conn (Y Power Splitter) To power camera and DVR from one source  RCABNC, MBNCOUP, FRCACOUP, MRCACOUP, BNCRCAM, 2 ea. FBNCRCA adapters  1 ea. 500ma power supply for use only when batteries are not being used.

Before Using  The max SD card size this unit can accommodate is 32Gb. This unit will not function on higher capacity cards.  The unit can be set to automatically record on motion detection. To set it up for this, refer to the CCM Important Notes and Programming document.  The included case is NOT WATERPROOF or SUBMERSIBLE. It is only weatherproof. It is able to be used outdoors with certain precautions. Water will ruin internal equipment and void the warranty. Case must be positioned, elevated and located in such a way that water will not enter in. Ideally the case should lay flat for optimal weatherproofing and safe operation of equipment and batteries.  You will still need to weatherproof the connections between the cable and the camera. Rubberized Weatherproof Electrical tape is commonly used for this.  There is a rounded out notch in the top of case below the cover in order to accommodate the power/video cables when the case is closed.

Changing Lens on Bullet Camera

 We have included 3 extra lenses for your bullet camera in order for you to change the field of view as your needs change. Carefully unscrew the lens cap and make sure the glass in the cap does not fall or break. There may also be a separator ring and an o-ring. Take special note to make sure you know how to reassemble the camera.  After the cap is off you must loosen the set screw in the exposed threads of the camera before attempting to unscrew the lens.  When installing a lens you should have the camera powered up in order to be able to focus the lens properly. Do not overtighten the set screw. Just make it snug. Some cameras will have a small allen screw and others may have a small common screw about 1/16th of and inch. Make sure to use the correct tool so as not to ruin the set screw and possibly ruin the entire camera.

Prior to Assembly  The 773 comes packed for shipping. Some assembly is required prior to use. The included picture’s documentation will help considerably.  The 22-12VRB batteries may be shipping separately due to weight limitations. There will be a small bag of fastening hardware with each battery in order to connect the Red and Black battery wires.  Warning: Make sure to pay special attention to polarity of battery and cables. The red wire is positive and connects to the red

Assembly (Refer to Pictures to Help During Assembly). There are many ways to connect these parts and many applications for this package. We are only giving you a general overview as to the operation of the 773. 1. Begin by bench testing the entire assembly to become familiar with it. 2. Connect the DVR board to your TV by means of the 500ma power supply, CA-150, and FBNCRCA connector. Using the included remote control get familiar with DVR and program it to your requirements. The DVR board will store all preferences you change. For programming instructions, refer to the CCM Important Notes and Programming document. 3. Connect the battery to the Y splitter. 4. The 2 identical female ends of Y power splitter will then plug into the DVR and CA-150 male ends. 5. The BNC video connector on DVR connects to CA-150 or directly to the camera by means of the MBNCOUP adapter. 6. The opposite end of CA-150 connects to power and video of bullet camera. 7. Connect the solar panel to the wires on back. Pay special attention to the positive and negative. Connect the other end to the solar panel connection on the charge controller, still paying special attention to positive and negative. 8. Connect the charging controller to the 22 amp battery terminals using the included cable. This means that you will have 2 power connections to each of the battery terminals. One goes to the charging controller and other goes into the y connecter. This is what enables continual use.

The BNC cable on the 3 wire ribbon looking cable is for the camera. The female RCA cable is for audio recording. The male power cable is for power in to power the DVR.

The separate cable with male pin on one end connects to the DVR board to view and listen of recorded footage. as well as being able to position the camera if you have a setup monitor like our TFT25HR monitor. Otherwise yellow is video and white is audio when connecting to your TV for playback. Solar Charging Controller and Panel Thank you for shopping with us. Sales and Service 866-720-0779 or 618-257-1810