Display Hidden Notes to Specifier. (Don't Know How? Click Here) s15

SECTION 08250 ENTRY DOORS

Display hidden notes to specifier. (Don't know how? Click Here)

PART 1 GENERAL

1.1 SECTION INCLUDES

1.A. Steel entry doors.

1.B. Fiberglass entry doors.

1.2 RELATED SECTIONS

2.A. Section 06100 - Rough carpentry: Rough opening and framing for windows.

1.3 REFERENCES

3.A. AAMA/WDMA/CSA 101/I.S.2/A440 - NAFS - North American Fenestration Standard/Specification for windows, doors, and skylights.

3.B. CSA A440S1 - Canadian Supplement to AAMA/WDMA/CSA 101/I.S.2/A440 - NAFS

3.C. U.S. Department of Energy - Energy Star Windows Program

3.D. National Resources Canada - Energy Star Windows Program

3.E. National Fenestration Rating Council (NFRC) 100 - Procedure for Determining Fenestration Product U-factors

3.F. National Fenestration Rating Council (NFRC) 200 - Procedure for Determining Fenestration Product Solar Heat Gain Coefficient and Visible Transmittance at Normal Incidence

3.G. National Fenestration Rating Council (NFRC) 700 - Product Certification Program

1.4 SUBMITTALS

4.A. 08250-1 Submit under provisions of Section 01300.

4.B. Product Data: Manufacturer's data sheets on each product to be used, including: 4.B.1. Preparation instructions and recommendations. 4.B.2. Storage and handling requirements and recommendations. 4.B.3. Installation methods.

4.C. Shop Drawings: Provide drawing elevations of each opening with details of rough openings, anchorage and installation.

4.D. Selection Samples: For each finish product specified, two complete sets of colour chips representing manufacturer's full range of available colours and patterns.

4.E. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, colour, and patterns.

1.5 QUALITY ASSURANCE

5.A. Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.

5.B. Installer Qualifications: Minimum 2 year experience installing similar products.

5.C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 5.C.1. Finish areas designated by Architect. 5.C.2. Do not proceed with remaining work until workmanship is approved by Architect. 5.C.3. Refinish mock-up area as required to produce acceptable work.

1.6 PRE-INSTALLATION MEETINGS

6.A. Convene minimum two weeks prior to starting work of this section.

1.7 DELIVERY, STORAGE, AND HANDLING

7.A. Deliver and store products in manufacturer's unopened packaging bearing the brand name and manufacturer's identification until ready for installation.

7.B. Handling: Handle materials to avoid damage.

1.8 PROJECT CONDITIONS

8.A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under 08250-2 environmental conditions outside manufacturer's recommended limits.

1.9 SEQUENCING

9.A. Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.10 WARRANTY

10.A. Manufacturer warrants the following for its door products: 10.A.1. Unless otherwise specifically noted, skilled labor to repair or replace any affected component shall be provided for two years from the date of delivery. 10.A.2. IGU failure (evidenced by moisture within the IGU caused by failure of the hermetic seal), manufacturer shall supply a replacement unit (or complete sash, including IGU, at manufacturer's discretion) for the failed unit free of charge for as long as the ownership of the home by the purchaser. 10.A.3. Factory Painted Aluminum Extrusions: Peeling, cracking, flaking or blistering under normal use, application and proper care are warranted for ten years from the date of delivery.

PART 2 PRODUCTS

2.1 MANUFACTURERS

1.A. Acceptable Manufacturer: Ply Gem Canada Windows & Doors , which is located at: 7140 40 St. S.E.; Calgary, AB, Canada T2C 2B6; Toll Free Tel: 800-297-6102; Email: request info (); Web: plygem.ca

1.B. Web: http://plygem.ca.

1.C. Substitutions: Not permitted.

1.D. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 PERFORMANCE REQUIREMENTS

2.A. Product Standard: Comply with AAMA/WDMA/CSA 101/I.S.2/A440 for minimum standards of performance, materials, components, accessories, and fabrication unless more stringent requirements are indicated.

2.B. Performance Class and Grade: Rated per AAMA/WDMA/CSA 101/I.S.2/A440. 2.B.1. In Canada, Performance Grades for windows, doors and skylights shall be selected according to the Canadian Supplement A440S1 so as to be appropriate for the conditions and geographic location in which the window, door or skylight will be installed.

08250-3 Thermal Transmittance: Tested and certified per NFRC 100 maximum total fenestration product U-factor.

2.D. Solar Heat-Gain Coefficient (SHGC): Tested and certified per NFRC 200 maximum total fenestration product SHGC.

2.3 ENTRY DOORS

3.A. Style: Arts and Crafts Series: 3.A.1. Design: Craftsman. 3.A.2. Design: Prairie. 3.A.3. Design: Bungalow. 3.A.4. Design: Ranch.

3.B. Style: Traditional Series: 3.B.1. Design: Colonial. 3.B.2. Design: Victorian. 3.B.3. Design: Shingle. 3.B.4. Design: Tudor.

3.C. Style: Modern Series: 3.C.1. Design: Modern. 3.C.2. Design: post Modern. 3.C.3. Design: Contemporary.

3.D. Material: Steel panel. 3.D.1. Steel Skin: 24-gauge galvanized steel. 3.D.2. Core: Rigid polyurethane.

3.E. Material; Fiberglass. 3.E.1. Provide Fiber Stain Fiberglass Doors as manufactured by Ply Gem Building Products 3.E.1.a. Design: Entry doors and sidelights where indicated as scheduled. 3.E.1.a.1) Ply-Gem #: ___. 3.E.1.b. Grain Pattern: Fir - The fine grain of Douglas fir. 3.E.1.c. Grain Pattern: Rustic - A deep grain and plank detail that resembles distressed wood. 3.E.1.d. Grain Pattern: Mahogany - A tight hardwood grain that produces a rich finish. 08250-4 3.E.1.e. Grain Pattern: Oak - A distinctive oak grain pattern. 3.E.2. Provide Fiber Tuff Fiberglass Doors as manufactured by Ply Gem Building Products. 3.E.2.a. Design: Entry doors and sidelights where indicated as scheduled. 3.E.2.a.1) Ply-Gem #: ___.

3.F. Door Lites: 3.F.1. Design as indicated or scheduled. 3.F.1.a. Ply-Gem #: ___.

3.G. Internal Blinds: 3.G.1. Door lites with internal blinds are sealed in a dust-free environment. Blinds are raised and lowered and tilted available in white (W) or tan (T), with double glazing. 3.G.2. Design as indicated or scheduled. 3.G.2.a. Ply-Gem #: ___.

3.H. Provide venting sash as indicated or scheduled: 3.H.1. Available with clear or Low-E argon glass. 3.H.1.a. Ply-Gem #: ___.

3.I. Provide decorative glass as indicated or scheduled: 3.I.1.a. Ply-Gem #: ___.

2.4 FRAME

4.A. Interior Frame: 4.A.1. Interior Finish: Paint Grade Wood. 4.A.2. Interior Finish: Stain Grade Hem-Fir. 4.A.3. Interior Finish: Vinyl Wrapped White (prefinished).

4.B. Exterior Frame: 4.B.1. Exterior: Aluminum Clad 4.B.1.a. Colour: White. 4.B.1.b. Colour: Cashmere. 4.B.1.c. Colour: Beige. 4.B.1.d. Colour: Sable. 4.B.1.e. 08250-5 Colour: Slate Grey. 4.B.1.f. Colour: Clear Anodized. 4.B.1.g. Colour: Taupe. 4.B.1.h. Colour: Hunter Green. 4.B.1.i. Colour: Redwood. 4.B.1.j. Colour: Brown. 4.B.1.k. Colour: Black. 4.B.2. Exterior: Primed Brickmould. 2 inches (51 mm) and 3-1/4 inches (83 mm) as indicated. 4.B.3. Exterior: Stain Grade Brickmould - 2 inches (51 mm) and 3-1/4 inches (83 mm) as indicated. 4.B.4. Exterior: Vinyl Wrapped White Brickmould - 2 inches (51 mm) and 3-1/4 inches (83 mm) as indicated. Pre-finished. 4.B.5. Exterior: Renovation Aluminum Clad Brickmould 2 inches (51 mm): 4.B.5.a. Colour: White. 4.B.5.b. Colour: Cashmere. 4.B.5.c. Colour: Beige. 4.B.5.d. Colour: Sable. 4.B.5.e. Colour: Slate Grey. 4.B.5.f. Colour: Clear Anodized. 4.B.5.g. Colour: Taupe. 4.B.5.h. Colour: Hunter Green. 4.B.5.i. Colour: Redwood. 4.B.5.j. Colour: Brown. 4.B.5.k. Colour: Black.

4.C. Hinge: 4.C.1. Grade: Standard. 4.C.2. Grade: Ball bearing. 4.C.3. Grade: Adjustable. 4.C.4. Finish: Painted. 4.C.4.a. Ply-Gem #: ___. 4.C.5. Finish: Plated. 4.C.5.a. Ply-Gem #: ___. 08250-6 4.C.6. Provide Spring Hinge. 4.C.7. Provide high performance door sill. 4.C.8. Provide Sentry Multi-Point lock with door hardware and handle sets as follows: 4.C.8.a. Handle Set: Transitional. 4.C.8.b. Handle Set: Traditional. 4.C.8.c. Handle Set: Contemporary. 4.C.8.d. Handle Set: Classic. 4.C.8.e. Handle Set: Modern. 4.C.8.f. Finish: Painted. 4.C.8.f.1) Colour: White. 4.C.8.f.2) Colour: Beige. 4.C.8.f.3) Colour: Faux Bronze. 4.C.8.f.4) Colour: Matte Black. 4.C.8.g. Finish: Plated. 4.C.8.g.1) Colour: Brass 4.C.8.g.2) Colour: Antique Brass. 4.C.8.g.3) Colour: Brushed Chrome. 4.C.8.g.4) Colour: Polished Chrome. 4.C.8.g.5) Colour: Satin Nickel. 4.C.8.g.6) Colour: Oil Rubbed Bronze.

2.5 GLAZING

5.A. Energy Performance: 5.A.1. ENERGY STAR Zone- Canada (2015): _____. 5.A.2. Section 9.36 Energy Efficiency_____. 5.A.3. U-Value Metric: _____. 5.A.4. Energy Rating: _____. 5.A.5. SHGC: _____.

5.B. IGU Unit Construction: 5.B.1. Eco Max Shield 366: 5.B.1.a. 08250-7 Location/Elevation: _____. 5.B.1.b. Glass Product: _____. 5.B.2. Eco Shield 270: 5.B.2.a. Location/Elevation: _____. 5.B.2.b. Glass Product: _____. 5.B.3. Eco Gain 180: 5.B.3.a. Location/Elevation: _____. 5.B.3.b. Glass Product: _____.

PART 3 EXECUTION

3.1 EXAMINATION

1.A. Do not begin installation until substrates have been properly prepared.

1.B. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

2.A. Clean surfaces thoroughly prior to installation.

2.B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

3.A. Install in accordance with manufacturer's instructions and in proper relationship with adjacent construction. Sealing options should be based on best practices and codes prevalent for each situation/installation.

3.4 PROTECTION

4.A. Protect installed products until completion of project.

4.B. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

08250-8